PC1131 Electric Compressor WEB READY MAN
User Manual: PC1131
Open the PDF directly: View PDF 
.
Page Count: 16
| Download | |
| Open PDF In Browser | View PDF |
Senco Products Inc. 8485 Broadwell Road Cincinnati, Ohio 45244 PC1131 Electric Air Compressor Operating Instructions © 2006 by Senco Products, Inc. Warnings for the safe use of this tool are included in this manual. Questions? Comments? call SENCO’S toll-free Action-line: 1-800-543-4596 or e-mail: toolprof@senco.com Visit our Website www.senco.com PC1131 Electric Compressor Issued Oct. 18, 2006 3 4 5 6 7 COMPRESSOR FEATURES 4 10 6 11 7 8 9 15 1 3 5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 16 12 2 15 16 14 13 8 Motor/Pressure Switch Motor Thermal Overload Air Intake Filter Air Compressor Pump Safety relief valve Air Tank Drain Valves Air Tank Pressure Gauge Outlet Pressure Gauge Pressure Regulator Dipstick Oil Drain Delivery tube 115 Volt electric power cord Ventilation openings/ protective shroud Quick disconnect Cold start valve COMPRESSOR FEATURES 1) MOTOR/PRESSURE SWITCH: This switch is used to start or stop the air compressor. Moving the switch to the "Auto" (On) position will provide automatic power to the pressure switch which will allow the motor to start when the air tank pressure is below the factory set "cut-in" pressure. When in the On Position, the pressure switch stops the motor when the air tank pressure reaches the factory set "cut-out" pressure. For safety purposes, this switch also has a pressure release valve located below the switch designed to automatically release compressed air from the air compressor pump head and its discharge line when the air compressor reaches "cut-out" pressure or is shut off. This allows the motor to restart freely. Moving the switch to the "Off" position will remove power from the motor and stop the air compressor. 2) MOTOR THERMAL OVERLOAD: The electric motor has a manual resettable overload protector. If the motor draws excessive current for any reason, the thermal overload will cut off power, thus preventing the motor from being damaged. Wait until the motor is cool before pressing the reset button to begin working again. If multiple reset result in consistent trips, check service and/or reference extension cord sizing recommendations. 3) AIR INTAKE FILTER: This filter is designed to clean air coming into the pump. To ensure the pump continually receives a clean, cool, dry air supply this filter must always be clean and ventilation opening free from obstructions. The filter can be removed for cleaning by using warm, soapy water. Rinse the filter and air dry. Replace filter when necessary. 4) AIR COMPRESSOR PUMP: To compress air, the piston moves up and down in the cylinder. On the downstroke, air is drawn in through the air intake valve while the exhaust valve remains closed. On the upstroke, air is compressed, the intake valve closes and compressed air is forced out through the exhaust valve, into the discharge line, through the check valve and into the air tank. 1 3 4 2 8 9 7 5 5) SAFETY RELIEF VALVE: This valve is designed to prevent system failures by relieving pressure from the system if compressed air reaches a predetermined level. The valve is preset by the manufacturer and must not be modified in any way. To verify the valve is working properly, pull on the ring. Air pressure should escape. When the ring is released, it will reseat. 6) AIR TANK DRAIN VALVE: The drain valve is used to remove moisture from the air tank(s) after the air compressor is shut off. NEVER attempt to open the drain valve when more than 10 PSI of air pressure is in the air tank! To open the drain valve, turn the knob counterclockwise. 6 10 7) AIR TANK PRESSURE GAUGE: The air tank pressure gauge indicates the reserve air pressure in the air tank (s). 11 8) OUTLET PRESSURE GAUGE: The outlet pressure gauge indicates the air pressure available at the outlet side of the regulator. This pressure is controlled by the regulator and is always less or equal to the air tank pressure. 9) PRESSURE REGULATOR: The air pressure coming from the air tank is controlled by the regulator knob. Turn the pressure regulation knob clockwise to increase discharge pressure, and counterclockwise to decrease discharge pressure. 13 10) OIL DIPSTICK: The dipstick will register the amount of oil in the pump. Oil level should be checked on a daily basis to ensure that it does not exceed the maximum notch or fall below the minimum notch on the dipstick. Air escaping from the vent is normal. 14 11) OIL DRAIN: The drain is provided to remove oil that has exceeded its service life. Drain oil into approved container and dispose of properly. Refill prior to starting. 15 12) RISK OF BURNS Head and discharge lines can be very hot. Do not touch until unit has cooled after use. 13) POWER CORD: Use only 115VAC 15A service. See extension cord recommendations on page 10. 14) VENTILATION OPENING: Keep opening free of obstructions to provide maximum cooling. 16 15) QUICK DISCONNECT: Spring loaded sealed coupling for easy hose removal. 1/4". 16) COLD START VALVE: The compressor is provided with a normally open valve. This valve will relieve compressed air for a few seconds at compressor start up allowing the motor to reach operating speed with low pump resistance. 12 9 3. 10 10 Remove plug from cylinder head port and replace w/ air filter. OPERATION PRE-START CHECKLIST: 1. Check oil level. Add if necessary. 2. Remove any moisture in the air compressor air tank. Remove excessive pressure with an air tool, then open the air tank drain valve in the bottom of the air tank. Close tightly when drained. WARNING: Risk of bodily injury. NEVER attempt to open the drain valve when more than 10 PSI of air pressure is in the air tank! 3. 4. 5. 6. Make sure the air compressor Motor Switch is in the “OFF” position. Make sure all safety valves are working correctly. Make sure all guards and covers are in place and securely mounted. Make sure that air filter is placed in proper opening. Remove plug before threading housing into compressor. START-UP: 1. Ensure the lever on the pressure switch box is in the “OFF” position. 2. Plug the power cord into a grounded outlet. 3. Move the lever on the pressure switch box to the “ON” position. 4. START/STOP: Turn to the ON position. This will allow the air compressor to “START” building up pressure in the air tanks and “STOP” when correct pressure is achieved. When pressure drops with usage, the air compressor willautomatically “START” building up pressure again. 5. Set pressure by adjusting the pressure regulator knob counterclockwise for less pressure and clockwise for more pressure. 6. If you notice any unusual noise or vibration, stop the air compressor and refer to “Troubleshooting”. SHUTDOWN: 1. To stop the air compressor, move the lever on the pressure switch box to the “OFF” position. NEVER stop the air compressor by unplugging it from the power source. This could result in risk of electrocution. 2. Drain air from the air tanks by releasing air with an attached air tool or by pulling on the safety relief valve rings. 3. Once pressure in the air tanks register under 10 psig, open the drain valve under each air tank to drain any moisture. 4. Allow the air compressor to cool down. 5. Wipe air compressor clean and store in a safe, non-freezing area. MAINTENANCE Read the instruction manual before performing maintenance. The following procedures must be performed when stopping the air compressor for maintenance or service. 1. Turn off air compressor. WARNING: Never assume the air compressor is safe to work on just because it is not operating. It could restart anytime! 2. Disconnect cord from main power supply. 3. Open all drains. 4. Wait for the air compressor to cool before starting service. MAINTENANCE CHART PROCEDURE Check pump oil level Oil leak inspection Drain condensation in air tank(s) Check for unusual noise/vibration Check for air leaks Inspect air filter Clean exterior of compressor Check safety relief valve Change pump oil* Replace air filter DAILY X X X X X WEEKLY X X MONTHLY X 200 HOURS X X *The pump oil must be changed after the first 50 hours of operation and every 200 hours or 3 months, whichever comes first. Recommended non-detergent straight weights. 11 11 ON position, motor runs continuously. 12 12 13 13 14 14 PC1131 2.0 running, 2.5 peak 3400 Oil Capacity 90 12 oz. 3.7 70 seconds 16 seconds 60 lbs 65 Running Duty Type Noise 20”x14.5”x16.5” S1 @ 100 psig 79 dBA 15 15
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Tagged PDF : Yes XMP Toolkit : 3.1-702 Instance ID : uuid:852be13c-0dc6-4a73-abb7-c94f929c2767 Document ID : adobe:docid:indd:4f43c3de-418f-11db-ba93-957aabad9c26 Rendition Class : proof:pdf Manifest Link Form : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream Manifest Placed X Resolution : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00 Manifest Placed Y Resolution : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00 Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches Manifest Reference Instance ID : uuid:2D3ADDC91D5EDB119336DAF09CAAA01F, uuid:7ACBF99F613FDB118487D5FC8B2A09F8, uuid:7CCBF99F613FDB118487D5FC8B2A09F8, uuid:7ACBF99F613FDB118487D5FC8B2A09F8, uuid:7ECBF99F613FDB118487D5FC8B2A09F8, uuid:80CBF99F613FDB118487D5FC8B2A09F8, uuid:0116FBA0623FDB118487D5FC8B2A09F8, uuid:0316FBA0623FDB118487D5FC8B2A09F8, uuid:8dea66fb-8d92-4ab0-95a6-1b97862e397c, uuid:B53ADAB6693FDB118487D5FC8B2A09F8, uuid:F0F89C06C541DB11A069C044F4BF7415, uuid:B73ADAB6693FDB118487D5FC8B2A09F8, uuid:4E105E77633FDB118487D5FC8B2A09F8, uuid:50105E77633FDB118487D5FC8B2A09F8, uuid:17231BDE205EDB11942DB31F7401717F, uuid:54105E77633FDB118487D5FC8B2A09F8 Manifest Reference Document ID : uuid:600D52C1DC5ADB11B203976DBB600EAB, uuid:79CBF99F613FDB118487D5FC8B2A09F8, uuid:7BCBF99F613FDB118487D5FC8B2A09F8, uuid:79CBF99F613FDB118487D5FC8B2A09F8, uuid:7DCBF99F613FDB118487D5FC8B2A09F8, uuid:7FCBF99F613FDB118487D5FC8B2A09F8, uuid:0016FBA0623FDB118487D5FC8B2A09F8, uuid:0216FBA0623FDB118487D5FC8B2A09F8, uuid:e7d240d8-90c2-4f77-850c-218fa5f07ee2, uuid:0816FBA0623FDB118487D5FC8B2A09F8, uuid:0A16FBA0623FDB118487D5FC8B2A09F8, uuid:4B105E77633FDB118487D5FC8B2A09F8, uuid:4D105E77633FDB118487D5FC8B2A09F8, uuid:4F105E77633FDB118487D5FC8B2A09F8, uuid:51105E77633FDB118487D5FC8B2A09F8, uuid:53105E77633FDB118487D5FC8B2A09F8 Create Date : 2006:10:17 17:13:44-04:00 Modify Date : 2006:10:18 13:35:55-04:00 Metadata Date : 2006:10:18 13:35:55-04:00 Creator Tool : Adobe InDesign CS2 (4.0.2) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 12709 bytes, use -b option to extract) Format : application/pdf Title : PC1131 Electric Compressor WEB-READY Creator : . Producer : Adobe PDF Library 7.0 Trapped : False Page Count : 16 Warning : [Minor] Ignored duplicate Info dictionaryEXIF Metadata provided by EXIF.tools