Panasonic_5.25 Jumpers Panasonic 5.25

Panasonic_5.25-jumpers Panasonic_5.25-jumpers

User Manual: Panasonic_5.25-jumpers

Open the PDF directly: View PDF PDF.
Page Count: 10

360 KB FDU PANASONIC JU-455-5 C09 SA450
JUMPER DESCRIPTION SETTING
DS1 Drive selected as DRIVE 1 OFF
DS2 Drive selected as DRIVE 2 ON
DS3 Drive selected as DRIVE 3 OFF
DS4 Drive selected as DRIVE 4 OFF
MX Drive selected by the Drive Select signal OFF
DS Drive selection enabled in a multidrive system ON
RD Ready signal enabled ON
DC Stores door closure OFF
WP Write Protect signal enabled ON
MM Drive motor enabled by the Motor On signal ON
MS Drive motor enabled by the Drive Select signal OFF
UA Front LED handled by the In Use signal OFF
DA Front LED handled by the Drive Select signal ON
RY PC XT-AT compatibility OFF
TM Terminator ON
3
Peripherals - Pocket Service Guide
5.25" FLOPPY DISK DRIVES 3-5
360 KB FDU PANASONIC JU-455-7 C09 SA450
JUMPER DESCRIPTION SETTING
DS1 Drive selected as DRIVE 1 OFF
DS2 Drive selected as DRIVE 2 ON
DS3 Drive selected as DRIVE 3 OFF
DS4 Drive selected as DRIVE 4 OFF
MX Drive selected permanently OFF
MM Drive motor enabled by the Motor On signal ON
MS Drive motor enabled by the Drive Select signal OFF
UA Front LED handled by the In Use signal OFF
DA Front LED handled by the Drive Select signal ON
RY PC XT-AT compatibility OFF
TM Terminator ON
DA UA
Peripherals - Pocket Service Guide
3-6 5.25" FLOPPY DISK DRIVES
1.2 MB FDU PANASONIC JU-475-2 C08 SA450
JUMPER DESCRIPTION SETTING
TM Terminator ON
DS1 Drive selected as DRIVE 1 OFF
DS2 Drive selected as DRIVE 2 ON
DS3 Drive selected as DRIVE 3 OFF
DS4 Drive selected as DRIVE 4 OFF
DS Selection of a drive in a multidrive system enabled ON
MX Drive selected permanently OFF
AT Drive for use in the system enabled ON
AX Stores the Drive Select signal OFF
RDY Standard Ready signal OFF
LR Stores the Ready signal OFF
DC Stores door closure ON
DS Door open OFF
BX Double speed OFF
CX Single speed ON
IRD Internal Ready signal OFF
SP Step Disk Change ON
DX Index Disk Change OFF
DO Disk Change drive selection OFF
UA Front LED controlled by the Ready signal OFF
DA Front LED controlled by the Drive Select signal ON
OA Front LED controlled by the Ready or Drive Select signal OFF
HA Front LED controlled by the Ready and Drive Select signals OFF
MM Motor drive enabled by the Motor On signal ON
MB Motor drive enabled by the Drive Select signal OFF
Peripherals - Pocket Service Guide
3-12 5.25" FLOPPY DISK DRIVES
1.2 MB FDU PANASONIC JU-475-3 C08
PANASONIC JU-475-3 C20 SA450
3
Peripherals - Pocket Service Guide
5.25" FLOPPY DISK DRIVES 3-13
JUMPER DESCRIPTION SETTING FOR
JU-475-3 C08 SETTING FOR
JU-475-3 C20
TM Terminator ON ON
DS1 Drive selected as DRIVE 1 OFF OFF
DS2 Drive selected as DRIVE 2 ON ON
DS3 Drive selected as DRIVE 3 OFF OFF
DS4 Drive selected as DRIVE 4 OFF OFF
MX Drive selected permanently OFF OFF
DA Front LED controlled by the Drive Select signal ON ON
UA Front LED controlled by the Ready signal OFF OFF
HA Front LED controlled by the Ready and Drive
Select signals OFF OFF
LA Front LED controlled by the Ready signal
selecting the drive OFF OFF
MS Motor drive enabled by the Drive Select signal OFF OFF
MM Motor drive enabled by the Motor On signal ON ON
HS Head loading controlled by the Drive Select signal
(not used) OFF OFF
HL Head loading controlled by the Drive Select and
Ready signals (not used) OFF OFF
HM Head loading controlled by the Motor On signal
(not used) OFF OFF
OP Dual Mode ON ON
1M Single Mode (only 1 MB) OFF OFF
BX Double speed OFF ON
NAX Used with OP, BX and 1M OFF OFF
EX Active index after head positioning on any track OFF OFF
TH Interface connector pin 34 selected by the Drive
Select signal OFF OFF
DD Not used OFF OFF
MDB Pin 34 is kept low by Drive Select when the
support is not inserted and by the first Drive
Select when the support has been changed
ON ON
MDA OFF OFF
Peripherals - Pocket Service Guide
3-14 5.25" FLOPPY DISK DRIVES
1.2 MB FDU PANASONIC JU-475-4 C08
PANASONIC JU-475-4 C20 SA450
3
Peripherals - Pocket Service Guide
5.25" FLOPPY DISK DRIVES 3-15
JUMPER DESCRIPTION SETTING FOR
JU-475-4 C08 SETTING FOR
JU-475-4 C20
TM Terminator ON ON
DS1 Drive selected as DRIVE 1 OFF OFF
DS2 Drive selected as DRIVE 2 ON ON
DS3 Drive selected as DRIVE 3 OFF OFF
DS4 Drive selected as DRIVE 4 OFF OFF
MX Drive selected permanently (used on single drive
systems only) OFF OFF
UA Front LED controlled by the Ready signal OFF OFF
DA Front LED controlled by the Drive Select signal ON ON
LA Front LED controlled by the stored Ready function OFF OFF
HA Front LED controlled by the Ready and Drive
Select signals OFF OFF
MS Motor drive enabled by the Motor On signal OFF OFF
HL Head loading controlled by the Drive Select and
Ready signals (not used) OFF OFF
HS Head loading controlled by the Drive Select signal
(not used) OFF OFF
HM Head loading controlled by the Motor On signal ON ON
HL1 Head loading controlled the stored Ready function
(not used) OFF OFF
PH Dual mode (positive high density) ON ON
NH Dual mode (negative high density) (not used) OFF OFF
AX Mode Select with the storage of Drive Select OFF OFF
1M Single Mode (only 1 MB) OFF OFF
BX Double speed OFF ON
RDY Standard Ready signal OFF OFF
DC Disk Change 1 (reset via Step) ON ON
NDO Disk In OFF OFF
DO Disk Out OFF OFF
DD Disk Change 2 (reset via Drive Select) OFF OFF
TH Pin 34 of the interface connector selected by
Drive Select OFF OFF
GX Read Data is enabled by Write Gate, Write
Protect, Drive Select and when the head is
positioned on a track ON ON
EX Active index following the positioning of the head
on a track OFF OFF
1E Selects 96 TPI or 48 TPI (set at the factory) ON ON
RY Connects the Drive Status signal to interface
connector pin 34 (set at the factory) ON ON
ST Not used OFF OFF
OF Not used OFF OFF
Peripherals - Pocket Service Guide
3-16 5.25" FLOPPY DISK DRIVES
1.2 MB FDU PANASONIC JU-475-5 C08 (to lev. 02)
PANASONIC JU-475-5 C20 SA450
3
Peripherals - Pocket Service Guide
5.25" FLOPPY DISK DRIVES 3-17
JUMPER DESCRIPTION SETTING FOR
JU-475-5 C08 SETTING FOR
JU-475-5 C20
TM Terminator OFF OFF
DS1 Drive selected as DRIVE 1 OFF OFF
DS2 Drive selected as DRIVE 2 ON ON
DS3 Drive selected as DRIVE 3 OFF OFF
DS4 Drive selected as DRIVE 4 OFF OFF
DA Front LED controlled with the Drive Select signal ON ON
HA Front LED controlled with the Ready and Drive
Select signals OFF OFF
MS Motor drive enabled with the Motor On signal OFF OFF
HL Head loading controlled by Drive Select and
Ready (not used) OFF OFF
HS Head loading controlled by Drive Select (not used) OFF OFF
OP Dual Mode (high density positive) ON ON
AT Enables drive for use in system ON ON
AX Mode Select with storage of Drive Select OFF OFF
1M Single Mode (only 1 MB) OFF OFF
BX Double speed OFF ON
RDY Standard Ready signal OFF OFF
DC Disk change 1 (reset via step) ON ON
DD Disk change 2 (reset via Drive Select) OFF OFF
TH Pin 34 of interface connector selected by Drive
Select OFF OFF
GX Read Data enabled by Write Gate, Write Protect,
Drive Select and when the head has set on a track ON ON
EX Index active after the head has set on a track OFF OFF
1E Select 96 TPI or 48 TPI (set in the factory) ON ON
RY Connects Drive Status to pin 34 of the interface
connector ON ON
ST Not used OFF OFF
OF Not used OFF OFF
Peripherals - Pocket Service Guide
3-18 5.25" FLOPPY DISK DRIVES
1.2 MB FDU PANASONIC JU-475-5 C08 (from lev. 03)
PANASONIC JU-475-5 A72
PANASONIC JU-475-5 A08W SA450
Note:
Jumpers EX, GX, DD and TH have been removed from drive JU-475-5 C08 starting from this drive’s level
03 (March, ’94). To set the disk change mode 2 on this drive (as used on L1 with GO280D, FP1 fw2.4, FP4
fw3.7), solder a 15 Khom resistor at R18. The JU-475-5 C20 drive will no longer be available from March,
1994; instead, you can use drive JU-475-5 C08 by inserting jumper BX.
JUMPER DESCRIPTION SETTING
TM Termination OFF
DS1 Drive selected as DRIVE 1 OFF
DS2 Drive selected as DRIVE 2 ON
DS3 Drive selected as DRIVE 3 OFF
DS4 Drive selected as DRIVE 4 OFF
DA Front LED handled by the Drive Select signal ON
HA Front LED handled by the Ready and Drive Select signals OFF
MS Drive motor enabled by the Motor On signal OFF
OP Dual mode (positive high density) ON
AT Enables the drive for use in the system ON
AX Mode Select with Drive Select storage OFF
1M Single Mode (only 1 MB) OFF
BX Dual speed OFF
RDY Standard Ready signal OFF
DC Disk Change 1 (reset via Setup) ON
■
3
Peripherals - Pocket Service Guide
5.25" FLOPPY DISK DRIVES 3-19

Navigation menu