MAINTENANCE SCEDULE PRO 9D MANUAL

2019-02-21

: Pro-9D Manual PRO-9D MANUAL 2postlifts manuals s

Open the PDF directly: View PDF PDF.
Page Count: 29

9,000 POUND
TWO-COLUMN AUTOMOTIVE LIFT
Model:PRO-9D
MANUAL
ATLAS-Lift
PRO 9D Two-Column Automotive Lift
ii
Table of Contents
WARRANTY................................................................................................................................................ 2
PRO-9D Definition...................................................................................................................................... 3
PRO-9D Important Notes...........................................................................................................................3
PRO-9D BASIC SPECIFICATION........................................................................................................... 4
PRO-9D NINE TWO POST LIFT..............................................................................................................4
IMPORTANT FOUNDATION AND ANCHORING INFORMATION.................................................... 5
ANCHORING TIP SHEET......................................................................................................................... 6
PREPARATION...........................................................................................................................................6
GENERAL INFORMATION................................................................................................................... 7
RAISE LIFT............................................................................................................................................ 10
LOWER LIFT......................................................................................................................................... 10
SAFETY PROCEDURES........................................................................................................................ 11
MAINTENANCE SCHEDULE................................................................................................................. 12
DAILY PRE-OPERATION CHECK (8 HOURS)...................................................................................12
WEEKLY MAINTENANCE (40 HOURS).............................................................................................. 13
YEARLY MAINTENANCE....................................................................................................................... 13
TROUBLESHOOTING.............................................................................................................................14
OWNER / EMPLOYER RESPONSIBILTIES....................................................................................... 15
PRO 9D Installation/Parts Breakdown.................................................................................................. 17
PRO 9D Parts List.................................................................................................................................... 26
PRO 9D Two-Column Automotive Lift
1
9,000 POUND CAPACITY
MODEL: PRO-9D
TWO-COLUMN
AUTOMOTIVE LIFT
READ THIS ENTIRE MANUAL BEFORE OPERATION BEGINS
RECORD BELOW THE FOLLOWING INFORMATION WHICH IS LOCATED ON THE
SERIAL NUMBER DATA PLATE
Serial No.
Model No.
Date of Install
RECORD BELOW THE FOLLOWING CUSTOMER INFORMATION
Company Name
Contact Person *
Street Address
City
State
Phone
Fax
Email *
*Optional Fields
NOTE: To validate warranty, this information must be copied and either faxed or
mailed to:
PRO 9D Two-Column Automotive Lift
2
WARRANTY
The structural components on your new automotive lift are warranted for
five years on equipment. Operating components are warranted one year to
the original purchaser, to be free of defects in material and workmanship.
The manufacturer shall repair or replace at their option for this period those
parts returned to the factory freight prepaid which prove after inspection to
be defective.
This warranty only applies to the original purchaser of the equipment. This
warranty does not extend to defects caused by ordinary wear, abuse,
misuse, shipping damage, or damage as the result of improper
maintenance.
This warranty is exclusive and in lieu of all other warranties expressed or
implied.
In no event shall the manufacturer be liable for special, consequential or
incidental damages for the breach or delay in performance of the warranty.
The manufacturer reserves the right to make design changes or add
improvements to its product line without incurring any obligation to make
such changes on product sold previously.
This warranty shall be governed under the laws of the state of Texas, and
shall be subject to the exclusive jurisdiction of the Court in the state of
Texas in the county of Tarrant.
PRO 9D Two-Column Automotive Lift
3
PRO-9D Definition
This lift is a 9,000 lb. capacity, two-column lift. The safety system in this lift is
attached to the back of the carriage to provide a single point release that saves
time when operating.
PRO-9D Important Notes
Please read the Safety Procedures and operation instructions in this manual
before operating the lift. Proper installation is very important. To minimize the
chance of making an error in installation, please read this manual through
carefully before beginning installation. Check with building owner and/or
architect’s building plans when applicable. The lift should be located on a
relatively level floor with 4” thick, 3000 psi sufficiently cured concrete.
This is a vehicle lift installation / operation manual and no attempt is made or
implied herein to instruct the user in lifting methods particular to an individual
application. Rather, the contents of this manual are intended as a basis for
operation and maintenance of the unit as it stands alone or as it is intended and
anticipated to be used in conjunction with other equipment.
Proper application of the equipment described herein is limited to the parameters
detailed in the specifications and the uses set forth in the descriptive passages.
Any other proposed application of this equipment should be documented and
submitted in writing to the factory for examination. The user assumes full
responsibility for any equipment damage or personal injury that occurs as the
result of alteration of the equipment described in this manual or any subsequent
damages.
PRO 9D Two-Column Automotive Lift
4
PRO-9D BASIC SPECIFICATION
Capacity
9,000 lbs
Lifting Time
45 Seconds
Overall Height
142-1/2"
Overall Width
140"
Between Columns
110-1/4"
Drive Through
92-1/4
Height Shut-Off
134-1/2"
PRO-9D NINE TWO POST LIFT
SET-UP DIMENSIONS
PRO 9D Two-Column Automotive Lift
5
IMPORTANT FOUNDATION AND ANCHORING INFORMATION
1. Concrete shall have compression strength of at least 3,000 PSI and a
minimum thickness of 4” in order to achieve a minimum anchor
embedment of 3 ¼”. When using the standard supplied ¾” x 5 ½” long
anchors; if the top of the anchor exceeds 2 ¼” above the floor grade, you
DO NOT have enough embedment.
2. Use the existing holes in column base plate as a guide for drilling the ¾”
diameter holes into the concrete. Maintain a 6” minimum distance from any
slab edge or seam. Hole to hole spacing should be a minimum 6 ½” in any
direction. Concrete thickness or hole depth should be a minimum of 4”.
3. CAUTION: DO NOT install on asphalt or other similar unstable surface.
Columns are supported only by anchoring in floor.
4. Using the horseshoe shims provided, shim each column base as required
until each column is plumb. If one column has to be elevated to match the
plane of the other column, full size base shim plates should be used
(Reference Shim Kit). Torque anchors to 150 ft-lbs. Shim thickness MUST
NOT exceed ½” when using the 5 ½” long anchors provided with the lift.
Adjust the column extensions plumb.
5. If anchors do not tighten to 150 ft-lbs. Installation torque, replace the
concrete under each column base with a 4’ x 4’ x 6” thick 3,000 PSI
minimum concrete pad keyed under and flush with the top of existing floor.
Allow concrete cure before installing lifts and anchors.
PRO 9D Two-Column Automotive Lift
6
ANCHORING TIP SHEET
1. Anchors must be at least 6" from the edge of the slab or any seam.
2. Use a concrete hammer drill with a carbide tip, solid drill bit the same
diameter as the anchor, 3/4". (.775 to .787 inches diameter). Do not use
excessively worn bits or bits which have been incorrectly sharpened.
3. Keep the drill in a perpendicular line while drilling.
4. Let the drill do the work. Do not apply excessive pressure. Lift the drill
up and down occasionally to remove residue to reduce binding.
5. Drill the hole to depth equal to the length of anchor.
6. For better holding power blow dust from the hole.
7. Place a flat washer and hex nut over threaded end of anchor, leaving
approximately 1/2 inch of thread exposed carefully tap anchor. Do not
damage threads. Tap anchor into the concrete until nut and flat washer are
against base plate. Do not use an impact wrench to tighten. Tighten the nut,
two or three turns on average concrete (28-day cure). If the concrete is very
hard only one or two turns may be required. Check each anchor bolt with
torque wrench set to 150 foot pounds.
PREPARATION
The installation of this lift is relatively simple and can be accomplished by 2 men
in a few hours. The following tools and equipment are needed:
Appropriate lifting equipment
AW 32, 46 or other good grade Non-Detergent Hydraulic Oil SAE-10 (12
quarts)
Chalkline and 12' Tape Measure
Rotary Hammer Drill with 3/4" Drill Bit. Core Drill ReBar Cutter
recommended
Transit and a 4' Level
Sockets and Open Wrench set, 1/2" thru 1-1/2" (1-1/8" for 3/4" Anchors)
Locking Pliers, 8mm Socket Head Wrench
PRO 9D Two-Column Automotive Lift
7
GENERAL INFORMATION
1. Any freight damage must be noted on the freight bill before signing and
reported to the freight carrier with a freight claim established. Identify the
components and check for shortages. If shortages are discovered, contact
Hanmecson International, Inc. immediately.
2. Consult building owner and / or architect’s plans when applicable to establish
the best lift location. The lift should be located on a relatively level floor with
4” minimum thickness, 3000 psi concrete slab that has been properly cured.
There can be no cracks in the slab within 36” of the base plate location, and
no seams in the foundation within 6” of its location! Remember: any structure
is only as strong as the foundation on which it is located!
Check for ceiling clearance first to see how high the lift can be set up in your bay.
STEP 1: After unloading the lift, place it near the intended installation location.
STEP 2: Remove the shipping bands and packing materials from the lift. The
power unit and cylinders will be unpacked from the top.
STEP 3: Open the wrapping from the upper column and carefully remove the
parts from inside. Unbolt the column from the shipping brackets.
Unbolt the up-rights (Item # 20 in the parts list) from the columns and
assemble it to the column (Item # 19 in the parts list). See Fig. # 4.
STEP 4: Unpack the cylinders and open the oil port on each cylinder by
unscrewing the black plastic cap. Move the carriage up about 20” to
25”. Next, carefully slide the cylinder inside from the bottom of the
carriage. The oil port will face the backside of the column and the
notch on the bottom of the cylinder will fit into the hole in the center
of the base plate.
STEP 5: Position the columns facing each other 103” inside base plates (see
fig. 7). Square the columns by measuring diagonally from corner
points on base plates (within1/4”).
STEP 6: Using a 3/4" diameter concrete drill, drill the anchor holes in the main
side column, installing anchors as you go. Use a block of wood or
rubber mallet to drive anchor bolts in. Drill to a minimum depth of 4"
to insure maximum holding power. Drilling thru concrete
(recommended) will allow the anchor to be driven thru the bottom if
the threads are damaged.
STEP 7: Using a level, check column for side-to-side plumb and front-to-back
plumb. If needed, use horseshoe shims provided by placing shims
PRO 9D Two-Column Automotive Lift
8
underneath the base plate and around the anchor bolt. This will
prevent bending the column bottom plates (Shim thickness should
not exceed ½”). Tighten ¾” anchor bolts to 150 ft-lbs. of torque.
STEP 8: Using a tape measure, measure from back corner of the base to the
opposite back corner to insure legs are square. After confirming
dimensions, drill and install the anchors on the other side leg.
STEP 9: Level the second column as described in step #7.
STEP 10: Install the overhead cross beam. This cross beam has two pieces, to
be connected by six (6) bolts in the center of the beam. Be sure to
bolt them together by installing the bolts from inside the cross beam
out. This is to avoid interference with the cable when operating the
lift. Assemble cable pulleys and other parts as shown on Fig. 2 Next,
install the cross beam between two columns as shown on Fig. 11.
STEP 11: Install the safety latch on both side columns as shown on Fig. 6 and
7. Connect the safety release cable (parts #33) between two latches.
Check that the tension of the cable is tight. Pull the single point
release handle several times and check the tension again by making
sure both latches release at the same time when the handle is pulled.
STEP 12: Mount the power unit on the main side leg to the power unit bracket
using the four 5/16” bolts and nuts. Connect the power unit to the
fitting installed on the back of the main leg by using a short hose
supplied. See Fig. 10
STEP 13: Connect the equalizing cables (Item #32 on parts list) as shown in
Fig. # 8. Do not tighten at this stage of assembly.
STEP 14:Adjust the carriage cable tension. This is accomplished by tightening
the carriage adjustment nut on top of each carriage. The rear
carriage adjustment nut adjusts the opposite post carriage height.
The left post carriage nut adjusts the right column carriage, and the
NOTE!!!
The cable stud that connects to the front right corner of the carriage should
be connected first by pulling the stud through the carriage hole and up where
it is easy to be held by locking pliers. Pull the stud back into place after
threading at least ½” of the stud past the locknut. Connect the other ends to
the rear right corners of the carriage with at least ½” of thread showing past
the lock nut (cables run on the inside of the carriage). It may be necessary to
manually raise both carriages above the cylinder to provide enough space to
use the locking pliers. Make sure the carriage is set in the LOCK position.
PRO 9D Two-Column Automotive Lift
9
right column carriage nut adjusts the left column carriage. Adjust
each cable to approximately 1/2" side-to-side play. Check the latch
releases to insure the carriage is still engaged in the appropriate
latch.
STEP 15: Install all four swing arms, readjust the arm lock preinstalled to make
sure that gear rack are engaging the moon gear on the arm properly.
STEP 16: Remove the vent plug from the power unit and fill the reservoir. Use
a Ten Weight (SAE-10) non-foaming, non-detergent hydraulic fluid
(Texaco HD46 or equal). The unit will hold approximately twelve
quarts of fluid.
STEP 17: Make the Electrical hookup to the power unit; 220V Single Phase. It is
recommended that a 220 Volt, 30 Amp twist lock plug be installed in
the power line just ahead of the power unit. Use wire capable of
supporting a 30-amp circuit.
STEP 18: Do not place any vehicle on the lift at this time. Cycle the lift up and
down several times to insure latches engage properly and all air is
removed from the system. To lower the lift, first raised the lift to clear
the latches and then pull down the safety release handle to lower the
lift. If latches function out of sync, tighten the cable on the latch that
engages first.
WARNING!!!
The wiring must comply with local code. Have a certified electrician make the
electrical hook-up to the power unit. Protect each circuit with time delay fuse
or circuit breaker; 208v-230v single phase. 60 Hz 30 amp. Motor can not run
on 50 Hz with out a physical change to motor.
PRO 9D Two-Column Automotive Lift
10
RAISE LIFT
I. Press button on power unit
The safety latch mechanism will 'trip over' when the lift raises and drop into
each latch stop. To lock the lift you must press the Lower lever to relieve
the hydraulic pressure and let the latch set tight in a lock position.
Note: It is normal for an empty lift to lower slowly - it may be necessary to
add weight.
LOWER LIFT
1. Raise the lift until the latches clear the safety racks in both sides.
2. Pull down and hold the safety release handle.
3. Press the lowering lever at the power unit to lower the lift.
WARNING!!!
Always make sure latches on both sides clear the rack at same time when
pulling down the release handle by adjusting the cable.
ATTENTION!!!
ALWAYS LOCK THE LIFT BEFORE GOING UNDER THE VEHICLE.
NEVER ALLOW ANYONE TO GO UNDER THE LIFT WHEN RAISING
OR LOWERING.
PRO 9D Two-Column Automotive Lift
11
SAFETY PROCEDURES
Never allow unauthorized persons to operate lift. Thoroughly train new
employees in the use and care of lift.
Caution - the power unit operates at high pressure.
Remove passengers before raising vehicle.
Prohibit unauthorized persons from being in shop area while lift is in use.
Total lift capacity is 9,000-lbs. with 2,250-lbs. per swivel pad. Do not exceed
this capacity.
Prior to lifting vehicle, walk around the lift and check for any objects that
might interfere with the operation of lift and safety latches; tools, air hoses,
shop equipment.
When approaching the lift with a vehicle, center the vehicle between the
columns so that the tires will clear the swing arms easily. Slowly drive the
vehicle up between the posts. Have some one outside the vehicle guide the
driver.
Always lift vehicle using all four pads.
Never use lift to raise one end or one side of vehicle.
Raise vehicles about 3” and check stability by rocking.
Prior to lowering vehicle, walk around the lift and check for any objects that
might interfere with the operation of lift and safety latches; tools, air hoses,
shop equipment. Swing the arms out and slowly drive the vehicle out. Have
some one outside the vehicle guide the driver.
PRO 9D Two-Column Automotive Lift
12
MAINTENANCE SCHEDULE
The following periodic maintenance is the suggested minimum requirements and
minimum intervals; accumulated hours or monthly period, which ever comes
sooner. If you hear a noise not associated with normal lift operation, or, if there is
any indication of impending lift failure - CEASE OPERATION IMMEDIATELY! -
inspect, correct and/or replace parts as required.
DAILY PRE-OPERATION CHECK (8 HOURS)
The user should perform daily check.
Check safety lock audibly and visually while in operation
Check safety latches for free movement and full engagement with rack.
Check hydraulic connections, and hoses for leakage.
Check chain connections - bends, cracks-and loose links.
Check cables connections- bends, cracks-and looseness.
Check for frayed cables in both raised and lowered position.
Check snap rings at all rollers and sheaves.
Check bolts, nuts, and screws and tighten if needed.
Check wiring & switches for damage.
Keep base plate free of dirt, grease or any other corrosive substances.
Check floor for stress cracks near anchor bolts.
Check swing arm restraints.
ATTENTION! Daily check of safety latch system is very important - the
discovery of a potential device failure could prevent expensive property
damage, lost production time, serious personal injury, and even death.
WARNING!!!
OSHA AND ANSI REQUIRE USERS TO INSPECT LIFTING EQUIPMENT AT THE
START OF EVERY SHIFT. THESE AND OTHER PERIODIC INSPECTIONS ARE
THE RESPONSIBILITY OF THE USER.
PRO 9D Two-Column Automotive Lift
13
WEEKLY MAINTENANCE (40 HOURS)
Check anchor bolts torque to 150 ft-lbs for the ¾” anchor bolts.
Do not use impact wrench.
Check floor for stress cracks near anchor bolts
Check hydraulic oil level.
Check and tighten bolts, nuts, and screws.
Check cylinder pulley assembly for free movement or excessive wear on
cylinder yoke or pulley pin.
Check cable pulley for free movement and excessive wear.
YEARLY MAINTENANCE
Lubricate chain
Grease rub blocks and column surface contacting rub blocks
Change the hydraulic fluid - good maintenance procedure makes it mandatory
to keep hydraulic fluid clean. No hard fast rules can be established; -
operating temperature, type of service, contamination levels, filtration, and
chemical composition of fluid should be considered. If operating in dusty
environment shorter interval may be required.
The following items should only be performed by a trained maintenance expert.
Replace hydraulic hoses.
Replace chains and rollers.
Replace cables and sheaves.
Replace or rebuild air and hydraulic cylinders as required.
Replace or rebuild pumps / motors as required.
Check hydraulic cylinder rod and rod end (threads) for deformation or damage.
Relocating or changing components may cause problems. Each component in
the system must be compatible; an undersized or restricted line will cause a drop
in pressure. All valve, pump, and hose connections should be sealed and/or
capped until just prior to use. Air hoses can be used to clean fittings and other
components. However, the air supply must be filtered and dry to prevent
contamination. Most important - cleanliness - contamination is the most frequent
cause of malfunction or failure of hydraulic equipment.
PRO 9D Two-Column Automotive Lift
14
TROUBLESHOOTING
1. Motor does not operate
A. Breaker or fuse blown.
B. Motor thermal overload tripped. Wait for overload to cool.
C. Faulty wiring connections; call electrician.
D. Defective up button call electrician for checking.
2. Motor functions but lift will not rise
A. A piece of trash is under check valve. Push handle down and
push the up button at the same time. Hold for 10-15 seconds.
This should flush the system.
B. Check the clearance between the plunger valve of the
lowering handle. There should be 1/16".
C. Remove the check valve cover and clean ball and seat.
D. Oil level to low. Oil level should be just under the vent cap
port when the lift is down!!!
3. Oil blows out breather of power unit
A. Oil reservoir overfilled.
B. Lift lowered too quickly while under a heavy load.
4. Motor hums and will not run
A. Impeller fan cover is dented. Remove cover and straighten.
B. Faulty wiring.….... call electrician
C. Bad capacitor..….. call electrician
D. Low voltage........... call electrician
E. Lift overloaded .…. remove excessive weight from lift
5. Lift jerks going up and down
Air in hydraulic system. Raise lift all the way to top and return to
floor. Repeat 4-6 times. Do not let this overheat power unit.
6. Oil leaks
A. Power unit: if the power unit leaks hydraulic oil around the
tank-mounting flange check the oil level in the tank. The level
should be two inches below the flange of the tank. A
screwdriver can be used as a “dipstick”.
B. Rod end of the cylinder: the rod seal of the cylinder is out.
Rebuild or replace the cylinder.
C. Breather end of the cylinder: the piston seal of the cylinder
is out. Rebuild or replace the cylinder.
7. Lift makes excessive noise
A. Leg of the lift is dry and requires grease.
B. Cylinder pulley assembly or cable pulley assembly is not
moving freely.
C. May have excessive wear on pins or cylinder yoke.
PRO 9D Two-Column Automotive Lift
15
OWNER / EMPLOYER RESPONSIBILTIES
The Owner / Employer:
Shall established procedures to periodically maintain, inspect and care for the lift
in accordance with the manufactures recommended procedures to ensure its’
continued safe operations.
Shall provide necessary lockout / tagouts of energy sources per ANSI Z244.1 –
1982 before beginning any lift repairs.
Shall not modify the lift in any manner without prior written consent of the
manufacturer.
Shall display the operating instructions, “Lifting It Right” and “Safety Tips”
supplied with the lift in a conspicuous location in the lift area convenient to the
operator.
Shall insure that lift operators are instructed in the proper and safe use and
operation of the lift using the manufacturer’s instructions and “Lift It Right” and
“Safety Tips” supplied with the lift.
PRO 9D Two-Column Automotive Lift
16
Figure 1
Figure 1 Parts List
#
P/N
Name
Qty
1
HPRO-
1000/1000A
Column A
1
2
HPRO-3000
Upright
2
14
GB5781-86-
M12X40
M12×40 Hex
Bolts
24
15
GB93-87-φ 12
φ12 Lock
Washers
24
16
GB95-85-φ 12
φ12 Flat
Washers
58
17
GB41-86-M12
M12 Hex Nuts
29
PRO 9D Two-Column Automotive Lift
17
Figure 2
Figure 2 Parts List
#
P/N
Name
Qty
1
HPRO-
1000/1000A
Column A
1
2
HPRO-3000
Upright
2
3A
HPRO-4000A
Overhead
Cross Beam,
Female
Section
1
3B
HPRO-4000B
Overhead
Cross Beam,
Male Section
1
14
GB5781-86-
M12X40
M12×40 Hex
Bolts
24
15
GB93-87-φ 12
φ12 Lock
Washers
24
16
GB95-85-φ 12
φ12 Flat
Washers
58
17
GB41-86-M12
M12 Hex Nuts
29
PRO 9D Two-Column Automotive Lift
18
Figure 3
Figure 3 Parts List
#
P/N
Name
Qty
1
HPRO-
1000/1000A
Column A
1
28
HPRO-
1000/1000B
Column B
1
2
HPRO-3000
Upright
2
3A
HPRO-4000A
Overhead
Cross Beam,
Female
Section
1
3B
HPRO-4000B
Overhead
Cross Beam,
Male Section
1
14
GB5781-86-
M12X40
M12×40 Hex
Bolts
24
15
GB93-87-φ 12
φ12 Lock
Washers
24
16
GB95-85-φ 12
φ12 Flat
Washers
58
17
GB41-86-M12
M12 Hex Nuts
29
25
WG-1-M3/4" X
140
3/4"×140
Anchor Bolts
10
PRO 9D Two-Column Automotive Lift
19
Figure 4
Figure 4 Parts List
#
P/N
Name
Qty
#
P/N
Name
Qty
2
HPRO-3000
Upright
2
21
GB93-87 - φ 8
Cable Sheave
Bracket
2
18
GB5781-86-M6 X 16
M6 X 16 Hex Bolts
10
22
GB95-85 - φ 8
Hose Support
Bracket
2
19
GB93-87-φ 6 X 16
φ 6 Lock Washers
10
29
GB95-85 - φ 6
φ 6 Flat Washers
10
PRO 9D Two-Column Automotive Lift
20
Figure 5
Figure 5 Parts List
#
P/N
Name
Qty
1.2
30500-5001(B)-07
Bushing
2
1.5
30500-5001(B)-09
Shaft
2
1.6
30500-5001(B)-10
Spring
2
1.7
30500-8000-01B
Cover B
1
1.8
30500-5001(B)-24
Bushing
2
1.9
30500-5001(B)-25G1
Spring
1
1.10
30500-5001(B)-22
Safety Cam Plate, Slave Side
1
1.11
30500-5001(B)-21
Safety Latch
2
1.12
30500-8000-3
Cable Pulley Bracket B
1
13
30500-5001(B)-23
Treaded Shaft
1
18
GB5781-86-M6 X 16
M6 X 16 Hex Bolts
10
19
GB93-87-φ 6 X 16
φ 6 Lock Washers
10
29
GB95-85 - φ 6
φ 6 Flat Washers
10
40
GB818-85-M6 X 8
M6×8 Phillips Screws
16
41
GB78-85-M10 X 16
M10×16 Hex Head Screw
2
55
GB41-86-M6
M6 Nut
1
PRO 9D Two-Column Automotive Lift
21
Figure 6
Figure 6 Parts List
#
P/N
Name
Qty
1.1
30500-5001(B)-26G1
Safety Cam Plat
1
1.2
30500-5001(B)-07
Bushing
2
1.3
30500-5001(B)-12
Safety Release Handle
1
1.4
30500-8000-01A
Cover A
1
1.5
30500-5001(B)-09
Shaft
2
1.6
30500-5001(B)-10
Spring
2
1.8
30500-5001(B)-24
Bushing
2
1.9
30500-5001(B)-25G1
Spring
1
1.11
30500-5001(B)-21
Safety Latch
2
28
HPRO-1000A
Column B
1
29
GB95-85 - φ 6
φ 6 Flat Washers
10
30
30400-7000XDC
Front Arm A
1
39
WG-M10×φ35
M10 × φ 35 Knob
5
40
GB818-85-M6 X 8
M6×8 Phillips Screws
16
41
GB78-85-M10 X 16
M10×16 Hex Head Screw
2
55
GB41-86-M6
M6 Nut
1
PRO 9D Two-Column Automotive Lift
22
Figure 7
Figure 7 Parts List
#
P/N
Name
Qty
1
HPRO-1000/1000A
Column A
1
5
HPRO-2000
Carriage
2
24
YG20-9100
Hydraulic
Cylinders
2
29
GB95-85 - φ 6
φ 6 Flat
Washers
10
39
WG-M10×φ35
M10 × φ 35
Knob
5
40
GB818-85-M6 X 8
M6×8 Phillips
Screws
16
45
GB77-85-M6 X 10
M6 X10 Hex
Head Bolt
2
46
HPRO-Y002
Hydraulic Hose
1
47
30400-9030YZ
Hydraulic Hose
1
48
GB93-87 φ 10
φ10 Lock
Washers
4
49
GB41-86-M10
M10 Nuts
4
50
GB95-85 φ 10
φ 10 Flat
Washers
4
51
52
GB879-86- φ 3 X
26
φ 3 X 26 Roll
Pin
4
54
HPRO-Y003
Hydraulic Hose
1
55
GB41-86-M6
M6 Nut
1
PRO 9D Two-Column Automotive Lift
23
Figure 8
Figure 8 Parts List
#
P/N
Name
Qty
3.4
52006
4” Cable Sheave
4
32
HPRO-9000
Equalizing
Cable
2
33
30500-8000-4
Safety Release
Cable
1
34
GB95-85 φ 20
φ 20 Flat
Washer
4
35
WG-3/4"-16
3/4"-16 Nylon
Lock Nuts
4
36
HPRO-1007
Cable Pulley
Shaft
2
37
GB984.2-86 φ 25
φ 25 Snap Ring
4
38
52005
4.75" Cable
Pulley
2
PRO 9D Two-Column Automotive Lift
24
Figure 9
Figure 9 Parts List
#
P/N
Name
Qty
9
WT-3
Power Unit
1
22
GB95-85 - φ 8
φ 8 Flat
Washers
8
24
YG20-9100
Hydraulic
Cylinders
2
42
HPRO-Y001
Pipe Fitting
2
43
30400-9053YZ
Pipe Fitting
1
44
HYPORO-Y002
“T” Fitting
1
46
HPRO-Y002
Hydraulic
Hose
1
47
30400-9030YZ
Hydraulic
Hose
1
54
1WB-13
Hydraulic
Hose
1
PRO 9D Two-Column Automotive Lift
25
Figure 10
Figure 10 Parts List
#
P/N
Name
Qty
1
HPRO-1000/
1000A
Column A
1
2
HPRO-3000
Upright
2
3
HPRO-4000
Overhead
Cross Beam
1
4
30400-6014A
Short Truck
Adapter
4
5
HPRO-2000
Carriage
2
6
30400-7000X
Front Arm A
1
7
30400-6000X
Long Arm
2
8
30400-5005
Pin
4
9
WT-3
Power Unit
1
10
30400-6015A
Long Truck
Adapter
4
11
30400-6005-1
Lifting Pad
4
12
30400-7013
Saddle Pad
2
14
GB5781-86-
M12X40
M12×40 Hex
Bolts
24
15
GB93-87-φ 12
φ12 Lock
Washers
24
16
GB95-85-φ 12
φ12 Flat
Washers
58
17
GB41-86-M12
M12 Hex
Nuts
29
20
GB5781-86-M8
X 25
M8×25 Hex
Bolts
4
21
GB93-87 - φ 8
φ 8 Lock
Washers
4
22
GB95-85 - φ 8
φ 8 Flat
Washers
8
23
GB41-86-M8
M8 Hex Nuts
6
25
WG-1-M3/4" X
140
3/4"×140
Anchor Bolts
10
28
HPRO-1000B
Column B
1
30
30400-7000XDC
Front Arm A
1
PRO 9D Two-Column Automotive Lift
26
PRO 9D Parts List
1
HPRO-1000/1000A
Column A, Slave Side
1
1.1
30500-5001(B)-26G1
Safety Cam Plate, Master Side
1
1.2
30500-5001(B)-07
Bushing
2
1.3
30500-5001(B)-12
Safety Release Handle
1
1.4
30500-8000-01A
Cover A
1
1.5
30500-5001(B)-09
Shaft
2
1.6
30500-5001(B)-10
Spring
2
1.7
30500-8000-01B
Cover B
1
1.8
30500-5001(B)-24
Bushing
2
1.9
30500-5001(B)-25G1
Spring
1
1.10
30500-5001(B)-22
Safety Cam Plate, Slave Side
1
1.11
30500-5001(B)-21
Safety Latch
2
1.12
30500-8000-3
Cable Pulley Bracket B
1
2
HPRO-3000
Upright
2
2.1
HPRO-3000HJ
Upright Weldment
2
2.2
HPRO-3003
Hydraulic Hose Bracket
2
2.2
30500-8000-2-1
Safety Release Bracket A
2
3F
HPRO-4000F
Overhead Cross Beam, Female
Section
1
3M
HPRO-4000M
Overhead Cross Beam, Male
Section
1
3.1
HPRO-4001
Cross Beam Welement A
1
3.2
HPRO-4002
Cross Beam Welement B
1
3.3
HPRO-4003
Top Cable Pulley Shaft
1
3.4
52006
4" Cable Sheave
4
3.5
HPRO-4004
Spacer A
4
3.6
HPRO-4005
Spacer B
2
4
30400-6014A
Short Truck Adapter
4
5
HPRO-2000
Carriage
2
5.1
30400-5024
UHWM Sliding Bearing Block
16
6
30400-7000X
Front Arm, Left
1
7
30400-6000X
Long Arm
2
8
30400-5005
Pin
4
9
WT-3
Power Unit
1
10
30400-6015A
Long Truck Adapter
4
11
30400-6005-1
Lifting Pad
4
12
30400-7013
Saddle Pad
4
13
30500-5001(B)-23
Threaded Shaft
1
14
GB5781-86-M12X40
M12×40 Hex Bolts
24
15
GB93-87-φ 12
φ12 Lock Washers
24
PRO 9D Two-Column Automotive Lift
27
PRO 9D Parts List
16
GB95-85-φ 12
φ12 Flat Washers
58
17
GB41-86-M12
M12 Hex Nuts
29
18
GB5781-86-M6 X 16
M6 X 16 Hex Bolts
10
19
GB93-87-φ 6 X 16
φ 6 Lock Washers
10
20
GB5781-86-M8 X 25
M8×25 Hex Bolts
4
21
30400-8000-2
Cable Sheave Bracket A
4
22
30400-
Hose Support Bracket
2
23
GB41-86-M8
M8 Hex Nuts
6
24
YG20-9100
Hydraulic Cylinders
2
25
WG-1-M3/4" X 140
3/4"×140 Anchor Bolts
10
26
GB984.2-86 - φ 19
φ 19 Snap Rings
4
27
GB5781-86-M-12 X 25
M12×25 Hex Bolts
5
28
HPRO-1000B
Column B, Master Side
1
29
GB95-85 - φ 6
φ 6 Flat Washers
10
30
30400-7000XDC
Front Arm, Right
1
32
HPRO-9000
Equalizing Cable
2
33
30500-8000-4
Safety Release Cable
1
34
GB95-85 φ 20
φ 20 Flat Washer
4
35
WG-3/4"-16
3/4"-16 Nylon Lock Nuts
4
36
HPRO-1007
Cable Pulley Shaft
2
37
GB984.2-86 φ 25
φ 25 Snap Ring
4
38
52005
4.75" Cable Sheave
2
39
WG-M10×φ35
M10 × φ 35 Knob
5
40
GB818-85-M6 X 8
M6×8 Phillips Screws
16
41
GB78-85-M10 X 16
M10×16 Hex Head Screw
2
42
HPRO-Y001
Pipe Fitting
2
43
30400-9053YZ
Pipe Fitting
1
44
HPRO-Y002
T Fitting
1
45
GB879-86
M3 x 26mm Roll Pin
2
46
HPRO-Y002
Hydraulic Hose
1
47
30400-9030YZ
Hydraulic Hose
1
48
GB93-87- M10
10mm Lock Washer
4
49
GB41-86-M10
M10 Hex Nut
4
50
GB95-85 φ 10
φ 10mm Flat Washers
4
51
30400-5014
Gear Rack
4
52
GB879-86- φ 3 X 26
φ 3 X 26 Roll Pin
4
53
30400-5012-1
Spring
4
54
30400-5015
Pull Pin Handle Shaft
1
55
30400-5017
Spacer
4
56
GB5781-86-M6 X 35
M6 X 35 Hex Bolt
1

Navigation menu