Quectel BC35 G&BC28 AT Commands Manual V1.0
User Manual:
Open the PDF directly: View PDF
Page Count: 109 [warning: Documents this large are best viewed by clicking the View PDF Link!]
- About the Document
- Contents
- Table Index
- 1 Introduction
- 2 Implementation Status
- 3 3GPP Commands (27.007)
- 3.1. ATI Display Product Identification Information
- 3.2. ATE Set Command Echo Mode
- 3.3. AT+CGMI Request Manufacturer Identification
- 3.4. AT+CGMM Request Manufacturer Model
- 3.5. AT+CGMR Request Manufacturer Revision
- 3.6. AT+CGSN Request Product Serial Number
- 3.7. AT+CEREG EPS Network Registration Status
- 3.8. AT+CSCON Signalling Connection Status
- 3.9. AT+CLAC List Available Commands
- 3.10. AT+CSQ Get Signal Strength Indicator
- 3.11. AT+CGPADDR Show PDP Addresses
- 3.12. AT+COPS PLMN Selection
- 3.13. AT+CGATT PS Attach or Detach
- 3.14. AT+CGACT Activate or Deactivate PDP Context
- 3.15. AT+CIMI Request International Mobile Subscriber Identity
- 3.16. AT+CGDCONT Define a PDP Context
- 3.17. AT+CFUN Set UE Functionality
- 3.18. AT+CMEE Report UE Error
- 3.19. AT+CCLK Return Current Date and Time
- 3.20. AT+CPSMS Power Saving Mode Setting
- 3.21. AT+CEDRXS eDRX Setting
- 3.22. AT+CEER Extended Error Report
- 3.23. AT+CEDRXRDP eDRX Read Dynamic Parameters
- 3.24. AT+CTZR Time Zone Reporting
- 3.25. AT+CIPCA Initial PDP Context Activation
- 3.26. AT+CGAPNRC APN Rate Control
- 3.27. AT+CSODCP* Sending Originating Data via the Control Plane
- 3.28. AT+CRTDCP* Reporting Terminating Data via the Control Plane
- 4 3GPP Commands (27.005)
- 5 General Commands
- 5.1. AT+NRB Reboot the UE
- 5.2. AT+NUESTATS Query UE Statistics
- 5.3. AT+NEARFCN Specify Search Frequencies
- 5.4. AT+NSOCR Create a Socket
- 5.5. AT+NSOST SendTo Command (UDP Only)
- 5.6. AT+NSOSTF SendTo Command with Flags (UDP Only)
- 5.7. AT+NSORF Receive Command (UDP Only)
- 5.8. AT+NSOCL Close a Socket
- 5.9. +NSONMI Indicator of Arrived Socket Message (Response Only)
- 5.10. AT+NPING Test IP Network Connectivity to a Remote Host
- 5.11. AT+NBAND Set Supported Bands
- 5.12. AT+NLOGLEVEL Set Debug Logging Level
- 5.13. AT+NCONFIG Configure UE Behaviour
- 5.14. AT+NATSPEED Configure UART Port Baud Rate
- 5.15. AT+NCCID USIM Card Identification
- 5.16. AT+NFWUPD Firmware Update via UART
- 5.17. AT+NPOWERCLASS Set the Mapping for Band and Power Class
- 5.18. AT+NPSMR Power Saving Mode Status Report
- 5.19. AT+NPTWEDRXS Paging Time Window Value and eDRX Setting
- 5.20. AT+NPIN* PIN Operator
- 5.21. AT+QLEDMODE Set NETLIGHT LED Function Mode
- 6 Huawei’s IoT Platform Commands
- 6.1. AT+NCDP Configure and Query CDP Server Settings
- 6.2. AT+QSECSWT* Set Data Encryption Mode
- 6.3. AT+QSETPSK* Set PSK ID and PSK
- 6.4. AT+QLWSREGIND Register Control
- 6.5. AT+QLWULDATA Send Data
- 6.6. AT+QLWULDATAEX Send CON/NON Message
- 6.7. AT+QLWULDATASTATUS Query CON Messages Sent Status
- 6.8. AT+QLWFOTAIND Set DFOTA Update Mode
- 6.9. AT+QREGSWT Set Registration Mode
- 6.10. +QLWULDATAEXIND Message Sent Status Report (Response Only)
- 6.11. +QLWEVTIND LWM2M Event Report (Response Only)
- 7 Error Values
- 8 Reset Reasons
- 9 Examples
- 10 Appendix A Reference