Quectel BC95 G BC68 AT Commands Manual V1.2
User Manual:
Open the PDF directly: View PDF
Page Count: 155 [warning: Documents this large are best viewed by clicking the View PDF Link!]
- About the Document
- Contents
- Table Index
- 1 Introduction
- 2 3GPP Commands (27.007)
- 2.1. ATI Display Product Identification Information
- 2.2. ATE Set Command Echo Mode
- 2.3. AT+CGMI Request Manufacturer Identification
- 2.4. AT+CGMM Request Manufacturer Model
- 2.5. AT+CGMR Request Manufacturer Revision
- 2.6. AT+CGSN Request Product Serial Number
- 2.7. AT+CEREG EPS Network Registration Status
- 2.8. AT+CSCON Signalling Connection Status
- 2.9. AT+CLAC List Available Commands
- 2.10. AT+CSQ Get Signal Strength Indicator
- 2.11. AT+CGPADDR Show PDP Addresses
- 2.12. AT+COPS PLMN Selection
- 2.13. AT+CGATT PS Attach or Detach
- 2.14. AT+CGACT Activate or Deactivate PDP Context
- 2.15. AT+CIMI Request International Mobile Subscriber Identity
- 2.16. AT+CGDCONT Define a PDP Context
- 2.17. AT+CFUN Set UE Functionality
- 2.18. AT+CMEE Report UE Error
- 2.19. AT+CCLK Return Current Date and Time
- 2.20. AT+CPSMS Power Saving Mode Setting
- 2.21. AT+CEDRXS eDRX Setting
- 2.22. AT+CEER Extended Error Report
- 2.23. AT+CEDRXRDP eDRX Read Dynamic Parameters
- 2.24. AT+CTZR Time Zone Reporting
- 2.25. AT+CIPCA Initial PDP Context Activation
- 2.26. AT+CGAPNRC APN Rate Control
- 2.27. AT+CSODCP* Sending Originating Data via the Control Plane
- 2.28. AT+CRTDCP* Reporting Terminating Data via the Control Plane
- 2.29. AT+CGCONTRDP Read PDP Context Dynamic Parameters
- 2.30. AT+CGAUTH Define PDP Context Authentication Parameters
- 2.31. AT+CNMPSD No More PS Data
- 3 3GPP Commands (27.005)
- 4 General Commands
- 4.1. AT+NRB Reboot the UE
- 4.2. AT+NUESTATS Query UE Statistics
- 4.3. AT+NEARFCN Specify Search Frequencies
- 4.4. AT+NSOCR Create a Socket
- 4.5. AT+NSOST SendTo Command (UDP Only)
- 4.6. AT+NSOSTF SendTo Command with Flags (UDP Only)
- 4.7. AT+NQSOS Query the List of Pending Socket Message
- 4.8. AT+NSORF Receive Command
- 4.9. AT+NSOCO Connect Command (TCP Only)
- 4.10. AT+NSOSD Send Command (TCP Only)
- 4.11. AT+NSOCL Close a Socket
- 4.12. +NSONMI Indicator of Arrived Socket Message (Response Only)
- 4.13. +NSOCLI Socket Close Indicator (Response Only)
- 4.14. AT+NPING Test IP Network Connectivity to a Remote Host
- 4.15. AT+NBAND Set Supported Bands
- 4.16. AT+NLOGLEVEL Set Debug Logging Level
- 4.17. AT+NCONFIG Configure UE Behaviour
- 4.18. AT+NATSPEED Configure UART Port Baud Rate
- 4.19. AT+NCCID USIM Card Identification
- 4.20. AT+NFWUPD Firmware Update via UART
- 4.21. AT+NPOWERCLASS Set the Mapping for Band and Power Class
- 4.22. AT+NPSMR Power Saving Mode Status Report
- 4.23. AT+NPTWEDRXS Paging Time Window Value and eDRX Setting
- 4.24. AT+NPIN* PIN Operator
- 4.25. AT+NCSEARFCN Clear Stored EARFCN
- 4.26. AT+NIPINFO IP Address Information Report
- 4.27. AT+NCPCDPR Configure PDP Context Dynamic Parameters to be Read
- 4.28. AT+NQPODCP Query Pending Originating Data List via the Control Plane
- 4.29. AT+QLEDMODE Set NETLIGHT LED Function Mode
- 4.30. AT+QDNS Trigger DNS Domain Name Resolution
- 5 Huawei’s IoT Platform Commands
- 5.1. AT+NCDP Configure and Query CDP Server Settings
- 5.2. AT+QSECSWT Set Data Encryption Mode
- 5.3. AT+QSETPSK Set PSK ID and PSK
- 5.4. AT+QLWSREGIND Register Control
- 5.5. AT+QLWULDATA Send Data
- 5.6. AT+QLWULDATAEX Send CON/NON Message
- 5.7. AT+QLWULDATASTATUS Query CON Messages Sent Status
- 5.8. AT+QLWFOTAIND Set DFOTA Update Mode
- 5.9. AT+QREGSWT Set Registration Mode
- 5.10. AT+NMGS Send a Message
- 5.11. AT+NMGR Get a Message
- 5.12. AT+NNMI New Message Indications
- 5.13. AT+NSMI Send Message Indications
- 5.14. AT+NQMGR Query the Status of Messages Received
- 5.15. AT+NQMGS Query the Status of Messages Sent
- 5.16. AT+NMSTATUS Message Registration Status
- 5.17. +QLWEVTIND LwM2M Event Report (Response Only)
- 5.18. AT+QRESETDTLS Reset DTLS Mode
- 5.19. AT+QDTLSSTAT Query the State of DTLS
- 5.20. AT+QBOOTSTRAPHOLDOFF* Bootstrap Hold off Time
- 5.21. AT+QLWSERVERIP Set/Delete Bootstrap/LwM2M Server IP
- 5.22. AT+QSETBSPSK* Configure PSK ID and PSK to Bootstrap
- 5.23. AT+QBSSECSWT* Configure Bootstrap Server Connection Switches
- 6 Error Values
- 7 Reboot Reasons
- 8 Examples
- 8.1. Network Attachment
- 8.2. Send/Receive/Read a UDP Message
- 8.3. Send/Receive/Read a TCP Message
- 8.4. Examples Relating to Huawei’s IoT Platform
- 9 Appendix A Reference