Quectel BG96 AT Commands Manual V2.1
User Manual:
Open the PDF directly: View PDF
Page Count: 210 [warning: Documents this large are best viewed by clicking the View PDF Link!]
- About the Document
- Contents
- Table Index
- 1 Introduction
- 2 General Commands
- 2.1. ATI Display Product Identification Information
- 2.2. AT+GMI Request Manufacturer Identification
- 2.3. AT+GMM Request TA Model Identification
- 2.4. AT+GMR Request TA Revision Identification of Software Release
- 2.5. AT+CGMI Request Manufacturer Identification
- 2.6. AT+CGMM Request Model Identification
- 2.7. AT+CGMR Request TA Revision Identification of Software Release
- 2.8. AT+GSN Request International Mobile Equipment Identity (IMEI)
- 2.9. AT+CGSN Request Product Serial Number Identification
- 2.10. AT&F Set All Current Parameters to Manufacturer Defaults
- 2.11. AT&V Display Current Configuration
- 2.12. AT&W Store Current Parameters to User Defined Profile
- 2.13. ATZ Set All Current Parameters to User Defined Profile
- 2.14. ATQ Set Result Code Presentation Mode
- 2.15. ATV TA Response Format
- 2.16. ATE Set Command Echo Mode
- 2.17. A/ Repeat Previous Command Line
- 2.18. ATS3 Set Command Line Termination Character
- 2.19. ATS4 Set Response Formatting Character
- 2.20. ATS5 Set Command Line Editing Character
- 2.21. ATX Set CONNECT Result Code Format and Monitor Call Progress
- 2.22. AT+CFUN Set Phone Functionality
- 2.23. AT+CMEE Error Message Format
- 2.24. AT+CSCS Select TE Character Set
- 2.25. AT+QURCCFG Configure URC Indication Option
- 3 Serial Interface Control Commands
- 4 Status Control Commands
- 4.1. AT+CPAS Mobile Equipment Activity Status
- 4.2. AT+QCFG Extended Configuration Settings
- 4.2.1. AT+QCFG="nwscanseq" Configure RAT Searching Sequence
- 4.2.2. AT+QCFG="nwscanmode" Configure RAT(s) to be Searched
- 4.2.3. AT+QCFG="iotopmode" Configure Network Category to be Searched under LTE RAT
- 4.2.4. AT+QCFG="roamservice" Roam Service Configuration
- 4.2.5. AT+QCFG="band" Band Configuration
- 4.2.6. AT+QCFG="celevel" Get LTE Cat NB1 Coverage Enhancement Level
- 4.2.7. AT+QCFG="servicedomain" Service Domain Configuration
- 4.2.8. AT+QCFG="nb1/bandprior" Configure Band Scan Priority under LTE Cat NB1
- 4.2.9. AT+QCFG="psm/urc" Enable/Disable PSM Entering Indication
- 4.2.10. AT+QCFG="sgsn" UE SGSN Release Version Configuration
- 4.2.11. AT+QCFG="msc" UE MSC Release Version Configuration
- 4.2.12. AT+QCFG="pdp/duplicatechk" Establish Multi PDNs with the Same APN
- 4.2.13. AT+QCFG="ledmode" Configure NETLIGHT Output Mode
- 4.2.14. AT+QCFG="ims" IMS Function Control
- 4.2.15. AT+QCFG="urc/ri/ring" RI Behavior When RING URC is Presented
- 4.2.16. AT+QCFG="urc/ri/smsincoming" RI Behavior When Incoming SMS URCs are Presented
- 4.2.17. AT+QCFG="urc/ri/other" RI Behavior When Other URCs are Presented
- 4.2.18. AT+QCFG="risignaltype" RI Signal Output Carrier
- 4.2.19. AT+QCFG="urc/delay" Delay URC Indication
- 4.2.20. AT+QCFG="cmux/urcport" Configure URC Output Port for CMUX
- 4.2.21. AT+QCFG="apready" Configure AP_READY Pin
- 4.2.22. AT+QCFG="psm/enter" Trigger Module into PSM Immediately
- 4.3. AT+QINDCFG URC Indication Configuration
- 5 (U)SIM Related Commands
- 5.1. AT+CIMI Request International Mobile Subscriber Identity (IMSI)
- 5.2. AT+CLCK Facility Lock
- 5.3. AT+CPIN Enter PIN
- 5.4. AT+CPWD Change Password
- 5.5. AT+CRSM Restricted (U)SIM Access
- 5.6. AT+QCCID Show ICCID
- 5.7. AT+QPINC Display PIN Remainder Counter
- 5.8. AT+QINISTAT Query Initialization Status of (U)SIM Card
- 5.9. AT+QSIMDET (U)SIM Card Detection
- 5.10. AT+QSIMSTAT (U)SIM Card Insertion Status Report
- 6 Network Service Commands
- 6.1. AT+CREG Network Registration Status
- 6.2. AT+COPS Operator Selection
- 6.3. AT+CSQ Signal Quality Report
- 6.4. AT+CIND Indicator Control
- 6.5. AT+CPOL Preferred Operator List
- 6.6. AT+COPN Read Operator Names
- 6.7. AT+CTZU Automatic Time Zone Update
- 6.8. AT+CPSMS Power Saving Mode Setting
- 6.9. AT+QPSMS Power Saving Mode Setting
- 6.10. AT+QPSMCFG PSM Feature and Minimum Threshold Value Setting
- 6.11. AT+QPSMEXTCFG Modem Optimization
- 6.12. AT+QCSCON Signaling Connection Status
- 6.13. AT+CEDRXS e-I-DRX Setting
- 6.14. AT+CEDRXRDP Read Dynamic Parameters
- 6.15. AT+CTZR Time Zone Reporting
- 6.16. AT+QLTS Obtain the Latest Time Synchronized Through Network
- 6.17. AT+QNWINFO Query Network Information
- 6.18. AT+QCSQ Query and Report Signal Strength
- 6.19. AT+QSPN Display the Name of Registered Network
- 7 Call Related Commands
- 7.1. ATA Answer an Incoming Call
- 7.2. ATD Mobile Originated Call to Dial a Number
- 7.3. ATH Disconnect Existing Connection
- 7.4. AT+CVHU* Voice Hang up Control
- 7.5. AT+CHUP* Hang up a Call
- 7.6. +++ Switch from Data Mode to Command Mode
- 7.7. ATO Switch from Command Mode to Data Mode
- 7.8. ATS0 Set Number of Rings before Automatically Answering Call
- 7.9. ATS6 Set Pause before Blind Dialing
- 7.10. ATS7 Set the Time to Wait for Connection Completion
- 7.11. ATS8 Set the Time to Wait for Comma Dial Modifier
- 7.12. ATS10 Set Disconnection Delay after Indicating the Absence of Data Carrier
- 7.13. AT+CSTA* Select Type of Address
- 7.14. AT+CLCC List Current Calls of ME
- 7.15. AT+CR* Service Reporting Control
- 7.16. AT+CRC Set Cellular Result Codes for Incoming Call Indication
- 7.17. AT+CRLP* Select Radio Link Protocol Parameter
- 7.18. AT+QECCNUM Configure Emergency Call Numbers
- 7.19. AT+QHUP* Hang up a Call with a Specific Release Cause
- 8 Short Message Service Commands
- 8.1. AT+CSMS Select Message Service
- 8.2. AT+CMGF Message Format
- 8.3. AT+CSCA Service Center Address
- 8.4. AT+CPMS Preferred Message Storage
- 8.5. AT+CMGD Delete Messages
- 8.6. AT+CMGL List Messages
- 8.7. AT+CMGR Read Messages
- 8.8. AT+CMGS Send Messages
- 8.9. AT+CMMS More Messages to Send
- 8.10. AT+CMGW Write Messages to Memory
- 8.11. AT+CMSS Send Messages from Storage
- 8.12. AT+CNMA New Message Acknowledgement to UE/TE
- 8.13. AT+CNMI SMS Event Reporting Configuration
- 8.14. AT+CSDH Show SMS Text Mode Parameters
- 8.15. AT+CSMP Set SMS Text Mode Parameters
- 8.16. AT+QCMGS Send Concatenated Messages
- 8.17. AT+QCMGR Read Concatenated Messages
- 9 Packet Domain Commands
- 9.1. AT+CGATT Attachment or Detachment of PS
- 9.2. AT+CGDCONT Define PDP Context
- 9.3. AT+CGQREQ* Quality of Service Profile (Requested)
- 9.4. AT+CGQMIN* Quality of Service Profile (Minimum Acceptable)
- 9.5. AT+CGACT Activate or Deactivate PDP Contexts
- 9.6. AT+CGDATA* Enter Data Mode
- 9.7. AT+CGPADDR Show PDP Address
- 9.8. AT+CGREG Network Registration Status
- 9.9. AT+CGEREP Packet Domain Event Report
- 9.10. AT+CGSMS Select Service for MO SMS Messages
- 9.11. AT+CEREG EPS Network Registration Status
- 9.12. AT+QGDCNT Packet Data Counter
- 9.13. AT+QAUGDCNT Auto Save Packet Data Counter
- 10 Supplementary Service Commands*
- 10.1. AT+CCFC Call Forwarding Number and Conditions Control
- 10.2. AT+CCWA Call Waiting Control
- 10.3. AT+CHLD Call Related Supplementary Services
- 10.4. AT+CLIP Calling Line Identification Presentation
- 10.5. AT+CLIR Calling Line Identification Restriction
- 10.6. AT+COLP Connected Line Identification Presentation
- 10.7. AT+CSSN Supplementary Service Notifications
- 10.8. AT+CUSD Unstructured Supplementary Service Data
- 11 Hardware Related Commands
- 12 Appendix