220164.idw R220164 LC Collet Closer Parts
User Manual: R220164-LC-Collet-Closer-Parts Clausing == Clausing Lathe And Mill == Clausing Lathes
Open the PDF directly: View PDF 
.
Page Count: 7
1
1
2
2
A A
B B
13
5
4
2
6
7
8
9
10
11
13
14
16 17 18 19 20
21 22 23 24 25
26
ROYAL PRODUCTS
200 OSER AVE.
HAUPPAUGE, NY 11788
ANY QUESTIONS, CONTACT ROYAL PRODUCTS @ 1-800-645-4174 R220164 rev 0
ROYAL PRODUCTS 5C LEVER TYPE COLLET CLOSER
15
1
1
2
2
A A
B B
11R184723 HANDLE
2 2 R185504FIN PIVOT SCREW
3 2 R.312-24-HN 5/16-24 HEX NUT
4 1 R184716 BEARING & HOUSING
5 1 R185303 LOCK NUT
6 1 R185810 SPOOL
72R185511 LINKAGE PIN
1R181704 HANDLE ASSEMBLY (INCLUDES ITEMS 1 THRU 7)
81R185306 STOP NUT (SET SCREW INCLUDED P/N R1/4-20X.25HSSB)
9 3 R184502 PRESSURE FINGER
10 3 R.25X1.25DP 1/4 DIA X 1-1/4 LONG DOWEL PIN (FOR PRESSURE FINGER)
11 1 R184719 CAGE HOUSING
12 2 R10-32X.375FH 10-32 X 3/8 LONG FLAT HEAD SCREW- NOT SHOWN (FOR CAGE
HOUSING)
13 1R185703 LOCATING RING
14 3R10-32X.625CS 10-32 X 5/8 LONG CAP SCREW (FOR LOCATING RING)
15 1 R185975 REAR TUBE
16 1R5100-137 SNAP RING
17 1 R185976 CAGE & REAR TUBE ASSEMBLY (INCLUDES CAGE & ITEMS 15 & 16)
1R185985 COMPLETE REAR TUBE ASSEMBLY (INCLUDES ITEMS 9, 10, 11,
12, 17, 18, 19, 20 & 21)
18 1R184503 LOCATING FINGER
19 1R.125X.75DP 1/8 DIA X 3/4 LONG DOWEL PIN (FOR LOCATING FINGER)
20 1R185502 CAM PIN
21 1RLC-022B-1 SPRING (FOR CAM PIN)
22 1VARIES REAR END SPINDLE ADAPTER (CUSTOM MADE FOR EACH
MACHINE) NEED TO FILL OUT COLLET CLOSER ORDERING SHEET
23 1VARIES FRONT TUBE (LENGTH VARIES WITH EACH MACHINE)
24 1VARIES NOSE CAP (ONLY PROVIDED FOR MACHINES WITH THREADED OR
L-TYPE SPINDLE NOSES) SEE ATTACHED LIST FOR PART NUMBERS
25 1VARIES COLLET ADAPTER (VARIES WITH EACH MACHINE) SEE ATTACHED
LIST FOR COMMON ADAPTERS
26 1R182146 STANDARD LINKAGE ASSEMBLY (IF YOUR LINKAGE DOESN'T
LOOK AS SHOWN, YOU HAVE A CUSTOM LINKAGE- CALL WITH
MACHINE MAKE & MODEL FOR CUSTOM LINKAGE PART NUMBER)
PARTS LIST 5C LEVER TYPE COLLET CLOSER
ITEM QTY PART NUMBER DESCRIPTION
ROYAL PRODUCTS
200 OSER AVE.
HAUPPAUGE, NY 11788
ANY QUESTIONS, CONTACT ROYAL PRODUCTS @ 1-800-645-4174 R220164 rev 0
1
1
2
2
A A
B B
7.00 K
.88
ROYAL 5C LEVER TYPE COLLET CLOSER FRONT TUBE & REAR TUBE ASSEMBLY
REAR TUBE ASSEMBLY
FRONT TUBE
SEAM BETWEEN FRONT & REAR TUBE
L
J
6.13 5C THREADS
ROYAL PRODUCTS
200 OSER AVE.
HAUPPAUGE, NY 11788
ANY QUESTIONS, CONTACT ROYAL PRODUCTS @ 1-800-645-4174 R220164 rev 0
1
1
2
2
A A
B B
TO REPLACE YOUR EXISTING FRONT TUBE:
NEWER COLLET CLOSERS INCORPORATE A TWO PIECE TUBE DESIGN, OLDER COLLET CLOSERS
USED A ONE PIECE TUBE
IF YOU HAVE A TWO PIECE DESIGN: YOU WILL HAVE A SEAM 7.00" FROM THE END OF THE
REAR TUBE WHERE THE FRONT & REAR TUBES THREAD TOGETHER. CALCULATE YOUR FRONT
TUBE LENGTH (FTL) AND ORDER A NEW FRONT TUBE USING P/N R185980 & SPECIFY YOUR FTL
IF YOU HAVE A ONE PIECE DESIGN: YOU WILL NEED A NEW FRONT & REAR TUBE.
MEASURE THE OVER ALL LENGTH OF THE TUBE AND SUBTRACT 6.13" TO GET THE FRONT TUBE
FTL. ORDER A NEW FRONT TUBE USING P/N R185980 & SPECIFY YOUR FTL. YOU WILL ALSO
NEED A NEW REAR TUBE. YOU CAN BUY JUST THE REAR TUBE (P/N R185975) WHICH WE
DON'T RECOMMEND BECAUSE YOU WILL HAVE TO PRESS OFF YOUR EXISTING CAGE ASSEMBLY
AND PRESS IT ONTO YOUR NEW REAR TUBE. WE RECOMMEND BUYING THE CAGE & REAR
TUBE ASSEMBLY (P/N R185976)
IF YOU DO NOT HAVE A FRONT TUBE TO MEASURE OR YOU ARE PUTTING THIS COLLET
CLOSER ON A DIFFERENT MACHINE YOU WILL HAVE TO FILL OUT THE COLLET CLOSER
ORDERING SHEET SO WE CAN CALCULATE THE CORRECT TUBE LENGTH
CALCULATING FRONT TUBE LENGTH (FTL):
THERE ARE A FEW DIFFERENT WAYS TO CALCULATE YOUR FRONT TUBE LENGTH (FTL)
1. THREAD FRONT TUBE OFF OF REAR TUBE (RIGHT HAND THREAD) AND MEASURE OVERALL
LENGTH OF FRONT TUBE (DIMENSION L)
OR
2. MEASURE OVER ALL LENGTH OF FRONT & REAR TUBE ASSEMBLY (DIMENSION J) AND
SUBTRACT 6.13"
OR
3. MEASURE FROM END OF FRONT TUBE TO SEAM BETWEEN FRONT & REAR TUBES
(DIMENSION K) AND ADD .88"
ROYAL PRODUCTS
200 OSER AVE.
HAUPPAUGE, NY 11788
ANY QUESTIONS, CONTACT ROYAL PRODUCTS @ 1-800-645-4174 R220164 rev 0
1
1
2
2
A A
B B
PARTS LIST- COMMON 5C COLLET ADAPTERS
A-TYPE 5C COLLET ADAPTERS
A2-5 MOUNT P/N R188767
A2-6 MOUNT P/N R188751
D-TYPE CAM-LOCK 5C COLLET ADAPTERS
D1-3 MOUNT P/N R188762
D1-4 MOUNT P/N R188763
D1-5 MOUNT P/N R188764
D1-6 MOUNT P/N R188765
D1-8 MOUNT P/N R188766
TAPER MOUNT 5C COLLET ADAPTERS
-SPECIFY GAGE LINE DIAMETER OF SPINDLE'S INTERNAL TAPER
TO THE NEAREST THOUSANDTH OF AN INCH. (THIS IS THE
LARGE INTERNAL DIAMETER AT THE FACE OF THE SPINDLE)
THIS DIMENSION MAY BE OBTAINED BY INSERTING A CENTER
OR SLEEVE INTO SPINDLE AND MEASURING ITS OD SQUARE
AGAINST THE SPINDLE NOSE. IF NO SLEEVE OR CENTER IS
AVAILABLE, MEASURE ID BEHIND ANY CHAMFER OR RADIUS
AND INDICATE HOW DEEP MEASUREMENT WAS TAKEN.
-SPECIFY SPINDLE'S INTERNAL TAPER
(#5MT, #12 JARNO, ASA-250, ETC.)
REPLACING COLLET ADAPTER PIN-
DRILL OUT OLD PIN, INSERT 1/8" DIA COLD ROLLED
STEEL PIN. CUT PIN TO PROTRUDE .050" INTO BORE & .050"
ABOVE TAPER, PEEN END TO EXPAND, FILE SMOOTH W/ TAPER
ROYAL PRODUCTS
200 OSER AVE.
HAUPPAUGE, NY 11788
ANY QUESTIONS, CONTACT ROYAL PRODUCTS
@ 1-800-645-4174 R220164 rev 0
1
1
2
2
A A
B B
SPINDLE TYPE NOSE CAP OAL NOSE CAP P/N SPANNER WRENCH P/N
L-00 (3.75-6 UN) N/A R184219 N/A
L-0 (4.50-6 UN) N/A R184218 N/A
L-1 (6.00-6 UN) N/A R184226 N/A
L-2 (7.75-5 UN) N/A R184246 N/A
2.25-8 UN 1.125 R184220 R34-225
2.25-8 UN 1.375 R184222 R34-225
2.25-8 UN 1.25 R184221 R34-225
2.375-6 UN 1.75 R184244 R34-228
NOSE CAP & SPANNER WRENCH PART LIST
(ONLY USED FOR MACHINES WITH THREADED OR L-TYPE SPINDLE NOSES)
ROYAL PRODUCTS
200 OSER AVE.
HAUPPAUGE, NY 11788
ANY QUESTIONS, CONTACT ROYAL PRODUCTS @ 1-800-645-4174 R220164 rev 0
Collet Closer Ordering Sheet
Tel: 1.800.645.4174 •Fax: 1.800.424.2082 •www.royalprod.com
32
.
A Overall length of lathe spindle to the nearest 1/32".
B1 O.D. of rear of spindle to the nearest thousandth of an inch.
B2 O.D. thread (if applicable). Specify major diameter, pitch, and right or left hand.
C1 Length of diameter B1.
C2 Distance from rear of spindle to end of thread.
DSpindle bore(1.375 min. to clear drawtube).
FDistance from the rear of the spindle to guard. Fill in measurement and check type below.
GSelect spindle type: D1-3 D1-4 D1-5 D1-6 D1-8 A2-4 A2-5 A2-6 A2-8
HGage line diameter of internal taper.
IInternal spindle taper (5MT, 6MT, 12 Jarno, etc.).
SECTION B-B
SCALE 1 / 2
Name of Machine: Model: Swing:
Customer Name: Phone #:
.
MACHINE SPINDLE
.
Because lathe spindle dimensions and guard configurations frequently vary, it may be necessary to complete this ordering
sheet and submit it with your collet closer order. If you have any questions on how to obtain any of the required dimensions,
please contact a Royal applications engineer at 1-800-645-4174.
SECTION A-A
SCALE 0.07 : 1
A
A
BCD
B1 D
C1
B2
C2
A
IH
G
FLUSH RECESSED PROTRUDING
FF
