SC 250 Manual Insert
User Manual:
Open the PDF directly: View PDF 
.
Page Count: 20
| Download | |
| Open PDF In Browser | View PDF |
SPINCAT SC 250 ROTARY NOZZLE USER MANUAL PL 544 REV B (05/2018) TABLE OF CONTENTS .MANUFACTURER’S INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 DESCRIPTION OF EQUIPMENT AND INTENDED USE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 KEY FEATURES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SYSTEM ASSEMBLY - OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 PRE-RIH CHECKLIST .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 LUBRICANT REPLACEMENT INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 HIGH PRESSURE SEAL REPLACEMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 DISASSEMBLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 ASSEMBLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 TOOL STORAGE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 REPLACEMENT PART WEAR INFORMATION .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 MAINTENANCE, PARTS, AND OVERHAUL KITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 TERMS AND CONDITIONS AND WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 2 866-795-1586 • WWW.STONEAGETOOLS.COM MANUFACTURER’S INFORMATION StoneAge Inc. StoneAge Europe 466 S. Skylane Drive Unit 2, Britannia Business Centre Durango, CO 81303, USA Britannia Way Phone: 970-259-2869 Malvern WR14 1GZ Toll Free: 866-795-1586 United Kingdom www.stoneagetools.com Phone: +44 (0) 1684 892065 This manual must be used in accordance with all applicable national laws. The manual shall be regarded as a part of the machine and shall be kept for reference until the final dismantling of the machine, as defined by applicable national law(s). Updated manuals can be downloaded at: https://www.stoneagetools.com/manuals SPECIFICATIONS Tool Family: Tool Model: Pressure Range: Flow Range: Flow Rating: Rotation Speed: Inlet Connection: PSI Loss (@ 1 bpm): Tension (pull): Compression (set down): Outside Diameter: Overall Length: Weight: Maximum Temperature: SpinCat SC-250 1-5k psi (70-340 bar) 1 to 3 bpm (40 to 120 gpm) 7.5 Cv 80-150 rpm 1-1/2 AMMT 31 psi (2 bar) Safe load to 20000 lbs (9072 kg) Safe load to 25000 lbs (11340 kg) 2.5 in. 64 mm 16 in. 406 mm 15.9 lbs 7.2 kg 390° F 200° C JETTING The standard nozzle head has five ports with 1/8 NPT threads — one at 15 degrees forward, two at 45 degrees forward, and two at 90 degrees to the axis of rotation. Some of the ports may be plugged in a balanced pattern to concentrate the flow in a particular direction. Fitfor-purpose head and porting designs are available to accommodate specific flow rates and applications. DESCRIPTION OF EQUIPMENT AND INTENDED USE Spincat tools provide a durable, controlled rotation solution for well intervention. A viscous fluid governor controls rotation speed to maximize jet power delivered to the tubing walls. By using only a few rotating jets, each jet is bigger to convey hard-hitting power. Replaceable jets are efficient and clean recesses and irregular surfaces without damaging the well pipe. Over thirty years of waterjet engineering back the SpinCat design, setting the standard for rotary nozzle performance and durability. KEY FEATURES: • Straight flow-through design with a leakfree high pressure seal, so pump power is not wasted. • Performs at temperatures up to 200°C, with up to 30% HCL and Nitrogen injection. • Rotating Assembly for Complete Coverage • Easy Field Serviceability • Durable Fluoro Elastomer Seals • Computerized Flow Calculations • Controlled Rotation, Increases Cleaning Power • Carbide Nozzles, Deliver the Hardest Hitting, Longest Lasting Jet Possible 866-795-1586 • WWW.STONEAGETOOLS.COM 3 OVERVIEW DESCRIPTION: The SpinCat™ is a self-rotating nozzle designed for coil tubing well service. The powerful rotating jets cover a large area for efficient cleaning. Jet reaction force (thrust) powers rotation of the head. An internal centrifugal speed control maintains rotation speeds of 80 to 150 rpm. The SpinCat™ uses a high viscosity synthetic gear oil for lubrication, such as Chevron HiPerSYN® 220, Mobil SHC™ 630 or an equivalent. The oil is available from StoneAge® as part number SC250 048. The tool has a straight flow-through design with a leak-free high pressure seal so pump power is not wasted. It has a 1-1/2 AMMT box inlet thread. The tool can be used at temperatures up to 200°C (392°F), and can be used with up to 30% HCL and Nitrogen injection. (Note: if used with HCL, flush tool with clean water after use.) If the SpinCat™ will be used with high external borehole pressures, make certain that the body of the tool is completely full of lubricating fluid; air pockets are compressible and this could lead to oil seal failure and loss of lubrication. The SpinCat™ can be used at operating pressures of 1000 to 5000 psi and flow rates of 1 to 3 bpm (42 to 126 gpm) with standard head porting. Custom porting can be ordered for use up to 5 bpm (200 gpm). FLOW RANGE PRESSURE R20 1000-5000 PSI 1-3 BPM The standard nozzle head has five ports with 1/8 npt threads; one at 15 degrees forward, two at 45 degrees forward and two at 90 degrees to the axis of rotation. Some of the ports may be plugged in a balanced pattern to concentrate the flow in a particular direction. Alternate head porting patterns may be added to the same head to accommodate different flow rates. Hi-flow Flushing, Perf Stim, and Forward Cutting configurations are available. Verify with SpinCat™ Jetting App that porting changes result in sufficient torque to ensure rotation. DANGER Operations with this equipment can be potentially hazardous. Caution must be exercised prior to and during machine and water jet tool use. Please read and follow all of these instructions, in addition to the guidelines in the WJTA Recommended Practices handbook, available online at www.wjta.org. Deviating from safety instructions and recommended practices can lead to severe injury and/or death. 4 866-795-1586 • WWW.STONEAGETOOLS.COM PRE-RIH CHECKLIST PRE-RIH CHECKLIST: • After receipt on location, visually inspect the SpinCat™ to ensure no small debris has entered the tool. NOTE: The SpinCat™ package includes a briefcase size Pelican® case. We recommend keeping the SpinCat™ and spare set screws and other parts inside the case. • Verify the threaded orifice nozzles are clear and installed correctly. DO NOT insert hard wire or nails or other objects into the orifices to verify that they are clear. Use a flashlight. Newly manufactured orifice nozzles now have flow straighteners inside the orifices. These improve the quality of the jet stream. Remember to filter or screen the fluids keeping particles to a size no larger than 1/3 the ID of the orifice nozzle. Example: CNP2 125 orifice nozzle: 0.125 ÷ 3 = 0.041 max particle size. • Verify there is no oil leaking from the set screw or body. If the set screw is missing and oil has leaked out then use a StoneAge® service kit syringe and refill the oil. IMPORTANT: Be sure to take time to work the air bubbles out of the oil. • Turn the SpinCat™ head by hand. It should rotate very smoothly but not spin freely. There should not be any stoppage or feeling of binding or catching internally. • Ensure the wiper seal on the inlet nut is in place. The function of this seal is to prevent debris from plugging the vent holes. The vent hole’s function is to vent internal pressure build-up should the high pressure (HP) tungsten impregnated seal fail or leak intermittently while reseating itself. If the wiper seal is lost or missing it can be replaced with a suitable size Viton® O-Ring as a temporary measure. • The SpinCat™ is made of hardened stainless steel for long service life with strong acids, chemicals and solvents. We recommend you do not use pipe wrenches on the SpinCat™. Customers who have SpinCats™ 2-4 years old and are still in excellent condition, NEVER use pipe wrenches on their SpinCats™. Over time teeth cuts accumulate on the inlet nut, the body and head and “chew up” the tool. Eventually these parts have to be replaced unnecessarily. Some customers do not feel this is of significant importance and if replacement parts becomes necessary we can supply them. • When function testing, watch for leakage around the orifice nozzles. Also watch for leakage along the body and behind the head. This indicates an improperly redressed tool. Also watch for leakage from around the wiper seal, the high pressure seal might leak during initial pressurization but should stop once enough pressure to achieve rotation has been reached. The only place water should be exiting the tool is through the nozzles. The head should rotate slowly and smoothly. • If the head does not rotate during a function test but it rotates easily by hand, it could be the pump rate and pressure must be increased or the tool is simply “tight” or “cold,” or there is very heavy oil in the tool and it will loosen up in the hole, or the SpinCat™ may be jetted improperly. Check the SpinCat™ Jetting App. A simple but frequent problem in function tests is the test fluid does not contain viscosity reducer but the job requires it due to extremely high friction pressures. 866-795-1586 • WWW.STONEAGETOOLS.COM 5 LUBRICANT FILL INSTRUCTIONS TOPPING OFF LUBRICANT: The SpinCat™ uses synthetic gear oil for a lubricant. To top off the tool with lubricant, follow steps below. If the tool is being rebuilt or the seal replaced, the lubricant may be poured directly into the body around the shaft before the inlet nut is installed. Once the inlet nut is installed, it is recommended to use the syringe with the port screw ports to completely remove all air bubbles. High borehole pressures make this a critically important step when assembling the tool. The procedure requires some patience, time and effort i.e. rotating the body back and forth to work out all air bubbles, wait, repeat. If a vice is available in the field we recommend removing the inlet nut and topping off through the open top, working the air bubbles out by rotating the body and allowing to sit. 1. 2. 3. 4. 5. 6. 7. Tilt the tool at a 45 degree angle and secure so that one port screw is at the topmost point Fill the syringe (BC 410) with lubricant. Remove both Port Plugs (SC250 026). Thread the syringe into bottom port screw. Hold the tool at an angle so the port with the syringe is lower. Squeeze fluid into the tool until all air bubbles stop coming out. Rotate the body back and forth from the head to work air bubbles out and inject oil. Repeat 8. Re-install the Port Plugs. 9. Store the Tool with inlet nut facing up. SC250 026 Port Plug with O-Ring (2) BC 410 Syringe 6 866-795-1586 • WWW.STONEAGETOOLS.COM HIGH PRESSURE SEAL REPLACEMENT TO REPLACE THE HIGH PRESSURE SEAL: 1. Unscrew the Inlet Nut (SC250 002-AMMT). 2. Remove the old Seat (SC250 011-C) and H.P. Seal (SC250 012-O). 3. Apply grease to and install new H.P. Seal into the shaft with the O-Ring groove end going in first. 4. Install new Seat (SC250 011-C) with the chamfered face toward Inlet Nut. 5. Thread Inlet Nut into Body; tighten to 50 ft-lb. 6. Top up the lubricant using the syringe as detailed in the maintenance section at left. 7. Re-install the Port Plugs. SC250 002-AMMT Inlet Nut CHAMFERED FACE SC250 011- C Seat, Carbide CHAMFERED FACE UP SC250 011- C Seat, Carbide FLAT FACE SC250 012-O H.P. Seal SC250 012-O H.P. Seal O-RING GROOVE END DETAIL VIEW OF H.P. SEAL & SEAT 866-795-1586 • WWW.STONEAGETOOLS.COM 7 DISASSEMBLY TO DISASSEMBLE THE SPINCAT SC-250: 1. 2. 3. 4. 5. Unscrew the Inlet Nut (SC250 002-AMMT) from the body. Remove the Seat (SC250 011-C) and H.P. Seal (SC250 012-O) from the bore of the Shaft. Remove the Shaft Seal (SC250 006) from the Inlet Nut if it is damaged and needs replacing. Unscrew the Body (SC250 003) from the Gland Nut (SC250 020). Pull off Bearings (WG 007) from Shaft; remove the Sleeve (SC250 230). SC250 003 Body SC250 002-AMMT Inlet Nut WG 007 Bearing (2) SC250 011- C Seat, Carbide SC250 012-O H.P. Seal SC250 230 Sleeve SC250 020 Gland Nut 8 866-795-1586 • WWW.STONEAGETOOLS.COM DISASSEMBLY 6. Remove Collar (SC250 115) from Shaft, lift off Weights (SC250 320), Hub (SC250 122) and Spring (SC250 326). 7. Remove Collar (SC250 117) from Shaft 8. Press off Bearings (SC250 009); remove Gland Nut (SC250 020). 9. Remove the two Shaft Seals (SC250 007) from the Gland Nut. SC250 018 Screw (2) SC250 019 Screw (2) SC250 117 Collar SC250 015 Collar SC250 320 Weights SC250 122 Hub, Spring Drive SC250 009 Bearing (2) SC250 020 Gland Nut SC250 326 Spring 866-795-1586 • WWW.STONEAGETOOLS.COM 9 ASSEMBLY TO ASSEMBLE THE SPINCAT SC-250: 1. 2. 3. 4. 5. 6. Install Shaft Seals (SC250 007) in Gland Nut (SC250 020) as shown. Lubricate the seals prior to installing. The use of a seal installation tool (SC250 106) is recommended. Install O-Ring (SC250 008) over threads of Gland Nut. Slide Gland Nut onto Shaft. Press Bearings (SC250 009) onto Shaft, down far enough to allow placing of Collar (SC250 117) in its groove. Install Collar (SC250 117) around Shaft, above bearings. If there is a gap between the bearings and the collar, the bearings need to be pushed back up against the Collar. Tighten screws to 15 in-lb. Place Spring (SC250 326) over Shaft; tang on Spring fits into slot between Collar Halves. SC250 018 Screw (2) DETAIL VIEW OF SHAFT SEALS SC250 117 Collar LIP WITH SPRING UP SC250 009 Bearing (2) LIP WITH SPRING DOWN SC250 020 Gland Nut SC250 007 Shaft Seal (2) SC250 008 O-Ring SC250 020 Gland Nut 10 866-795-1586 • WWW.STONEAGETOOLS.COM ASSEMBLY 7. Install Hub (SC250 122); tang on Spring should go into one slot on Hub. 8. Install Weights (SC250 320) and Collar (SC250 015). Tighten screws equally on both sides to 15 in-lb. 9. Install Sleeve (SC250 230). 10. Install Bearings (WG 007) over Shaft, down against Sleeve. 11. Apply anti-seize to threads and thread Body (SC250 003) onto Gland Nut. SC250 019 Screw (2) SC250 003 Body SC250 015 Collar SC250 320 Weights WG 007 Bearing (2) SC250 122 Hub, Spring Drive SC250 326 Spring SC250 230 Sleeve SC250 020 Gland Nut 866-795-1586 • WWW.STONEAGETOOLS.COM 11 ASSEMBLY 12. Install Shaft Seal (SC250 006) in Inlet Nut (SC250 002-AMMT) as shown. Lubricate the seal prior to installing. The use of a seal installation tool (SC250 106) is recommended. 13. Install O-Ring (SC250 008) and Weep Seal (SC250 021-F). 14. Install H.P. Seal (SC250 012-O) and Seat (SC250 011-C) as shown in the "High Pressure Seal Replacement" page. 15. Pour lubricating fluid into Body until completely filled, allow time for air to bubble out. Refer to the "Lubricant Fill Instructions" page for the importance of eliminating the air during assembly. Apply anti-seize to threads and install Inlet Nut into Body. Tighten Inlet Nut to 50 ft-lb. LIP WITH SPRING DOWN SC250 006 Shaft Seal SC250 002-AMMT Inlet Nut SC250 008 O-Ring SC250 011- C Seat, Carbide SC250 012-O H.P. Seal SC250 002AMMT Inlet Nut SC250 021 Weep Seal 12 866-795-1586 • WWW.STONEAGETOOLS.COM TROUBLESHOOTING HIGH-PRESSURE SEAL LEAK: • The high pressure seal may leak initially at lower pressures, but should pop closed as pressure is increased. A continuous leak at operating pressure from the weep holes indicates the need to replace the HP Seal and Seat. HP Seals wearing out too quickly can be an indication that the HP Seat is installed upside-down, or the tool is rotating too fast. If the tool is leaking, but not over rotating, the SC250 602 Seal Kit is required. TOOL WILL NOT ROTATE: • Check the nozzles for plugging or wear (nozzles have to be removed to check for obstructions). • Check that the nozzle sizes are correct for the desired flow and that the desired flow matches the head flow range. • Check that the nozzle sizes are installed in a balanced configuration. • If the tool feels rough when manually rotating the head, this indicates internal damage and SC250 610 Overhaul Kit will be required. • Check head by hand to make sure it rotates freely. If it does not rotate freely by hand, the tool needs to be disassembled and repaired. Research from field reports show that exceeding set-down weight may bend the headshaft ever so slightly and prevent rotation. LOCK-UP TROUBLESHOOTING TIP: • Rotate in reverse 1 1/4 to 1 1/2 turns to unlock braking mechanism. If tool rotates smoothly then redress may not be required. • If the head rotates freely by hand, check the jet sizes and calculate pressure loss thru the coil tubing and check with your distributor or StoneAge® to make certain there is enough jet torque to provide rotation. • Verify using the SpinCat™ Jetting app, contact your factory authorized SpinCat™ dealer or contact StoneAge®, Inc. TOOL ROTATES TOO FAST: • If the head rotates too fast, clean out old lubricating fluid and replace with fresh lubricant. • If tool is showing heavy scuffing damage to body, we suggest that the customer install an available fluted body on the SpinCat™. This page is intentionally left blank. STORAGE TOOL STORAGE: The SpinCat™ should NOT be stored in a used condition with wellbore and pumped fluids possibly migrating into the lubricant chamber. Flush with fresh water and perform a seal redress after HCL, Xylene or Toluene chemical treatment jobs. Downhole tools, especially thru tubing tools tend to be stored upside down in tool racks with threaded stubs welded to rack base. Storing the SpinCat™ in this manner allows air to collect at the top of the lubricant chamber. We recommend the SpinCat™ be stored with inlet nut facing up to avoid this air pocket. The SpinCat™ may also be stored horizontally. 866-795-1586 • WWW.STONEAGETOOLS.COM 13 REPLACEMENT PART WEAR INFORMATION • BODY AND INLET NUT WEAR: Follow these wear dimension guidelines to determine when to replace parts. Common scuffing wear pattern on Body Common scuffing wear pattern on Inlet Nut .050 Minimum Wall Ø 2.43 Minimum Outside Diameter SC250 003 Body Scuffing Wear .10 Minimum Allowable .10 Minimum Ø 2.36 Minimum SC250 020 Gland Assembly SC250 002 Inlet Nut Scuffing Wear • SHAFT/HEAD WEAR: Follow these wear dimension guidelines to determine when to replace parts. Potential wear groove by shaft seal lip. Ø 1.176 Minimum Allowable SC250 043 Shaft/Head Wear SECTION A-A Ø.757 Maximum Potential wear groove by high pressure seal. 14 Potential wear groove by shaft seal lips. Ø 1.372 Minimum Allowable NOTE: Scuffing wear on head does not affect balance or rotation. Head should be replaced when properly installed nozzle inserts extend beyond the head or body diameter to prevent rapid wear and potential failure of the nozzle inserts. Inspect nozzle orifices for wear out of round. Replace if visibly worn. 866-795-1586 • WWW.STONEAGETOOLS.COM MAINTENANCE PARTS & OVERHAUL KITS PARTS OVERVIEW SC250 012-O H.P. Seal SC250 008 O-Ring SC250 011-C Seat, Carbide SC250 002-AMMT Inlet Nut SC250 230 Sleeve SC250 003 Body SC250 006 Shaft Seal SC250 021 Weep Seal WG 007 Bearing (2) SC250 026 Port Plug with O-Ring (2) SC250 020 Gland Nut SC250 122 Hub, Spring Drive SC250 117 SC250 019 SC250 326 Collar Screw (2) Spring SC250 320.1 Weights SC250 115 Collar SC250 225 Garter Spring (2) SC250 043-R20 Head Shaft Weldment CNP2 Nozzles (5) SC250 007 Shaft Seal (2) SC250 009 Bearing (2) SC250 018 Screw (2) SC250 008 O-Ring MAINTENANCE & OVERHAUL KIT PARTS SC250 600 – LUBRICATION KIT SC250 610 - OVERHAUL KIT 1 1 2 1 1 1 1 2 2 2 1 1 1 2 1 1 1 2 BC 410 Syringe, 20CC PL 544 SC-250 Manual Insert SC250 026 Port Plug with O-Ring SC250 048 High Temp Visc, Not for SC-H, 6oz SC250 602 -SEAL REDRESS KIT 1 1 1 2 2 1 1 1 2 1 BJ 062-S Anti-seize, 2g PL 544 SC-250 Manual Insert SC250 006 Shaft Seal, Small SC250 007 Shaft Seal, Large SC250 008 O-Ring, Viton SC250 011-C Carbide Seat SC250 012-O HP/ High Temp Seal + O-Ring SC250 021 Weep Seal SC250 026 Port Plug with O-Ring SC250 048 High Temp Visc, Not for SC-H, 6oz BJ 062-S Anti-seize, 2g PL 544 SC-250 Manual Insert SC250 006 Shaft Seal, Small SC250 007 Shaft Seal, Large SC250 008 O-Ring, Viton SC250 009 Bearing SC250 011-C Carbide Seat SC250 012-O HP/ High Temp Seal + O-Ring SC250 021 Weep Seal Viton SC250 026 Port Plug with O-Ring SC250 048 High Temp Visc, Not for SC-H, 6oz SC250 230 Bronze Sleeve SC250 326 Spring WG 007 Bearing, Ball SC250 612 - TOOL KIT 1 SC250 106 Tool, Double Ended Seal 1 PL 544 SC-250 Manual Insert 866-795-1586 • WWW.STONEAGETOOLS.COM 15 TERMS AND CONDITIONS AND WARRANTY INFORMATION 1. Acceptance of Terms and Conditions. Receipt 3. Warranty. SELLER MAKES NO WARRANTIES OR of these Terms and Conditions of Sale (“Terms and REPRESENTATIONS AS TO THE PERFORMANCE Conditions”) shall operate as the acceptance by OF ANY PRODUCT EXCEPT AS SET FORTH IN THE StoneAge, Inc. (“Seller”) of the order submitted by STONEAGE LIMITED WARRANTY PROVIDED WITH THE the purchaser (“Buyer”). Such acceptance is made PRODUCT. expressly conditional on assent by Buyer to these Terms and Conditions. Such assent shall be deemed to have 4. Delivery. Seller is not obligated to make delivery by been given unless written notice of objection to any of a specified date, but will always use its best efforts to these Terms and Conditions (including inconsistencies make delivery within the time requested. The proposed between Buyer’s purchase order and this acceptance) is shipment date is an estimate. Seller will notify Buyer given by Buyer to Seller promptly on receipt hereof. promptly of any material delay and will specify the revised delivery date as soon as practicable. UNDER Seller desires to provide Buyer with prompt and efficient NO CIRCUMSTANCES SHALL SELLER HAVE ANY service. However, to individually negotiate the terms LIABILITY WHATSOEVER FOR LOSS OF USE OR of each sales contract would substantially impair FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES Seller’s ability to provide such service. Accordingly, the RESULTING FROM DELAY REGARDLESS OF THE product(s) furnished by Seller are sold only according REASON(S). to the terms and conditions stated herein and with the terms and conditions stated in any effective StoneAge All product(s) will be shipped F.O.B. point of origin, Dealer Agreement or StoneAge Reseller Agreement, if unless specifically agreed otherwise, and Buyer shall applicable. Notwithstanding any terms and conditions pay all shipping costs and insurance costs from that on Buyer’s order, Seller’s performance of any contract point. Seller, in its sole discretion, will determine and is expressly made conditional on Buyer’s agreement arrange the means and manner of transportation of the to these Terms and Conditions unless otherwise product(s). Buyer shall bear all risk of loss commencing specifically agreed to in writing by Seller. In the absence with the shipment or distribution of the product(s) from of such agreement, commencement of performance, Seller’s warehouse. Order shortages or errors must be shipment and/or delivery shall be for Buyer’s reported within fifteen (15) business days from receipt of convenience only and shall not be deemed or construed shipment to secure adjustment. No product(s) may be to be an acceptance of Buyer’s terms and conditions. returned without securing written approval from Seller. 2. Payment/Prices. Unless other arrangements have 5. Modification. These Terms and Conditions are been made in writing between Seller and Buyer, payment intended by Seller and Buyer to constitute a final, for the product(s) shall be made upon receipt of invoice. complete and exclusive expression of agreement The prices shown on the face hereof are those currently relating to the subject matter hereof and cannot be in effect. Prices invoiced shall be per pricelist in effect supplemented or amended without Seller’s prior written at the time of shipment. Prices are subject to increase approval. for inclusion of any and all taxes which are applicable and which arise from the sale, delivery or use of the 6. Omission. Seller’s waiver of any breach or Seller’s product(s), and the collection of which Seller is or may failure to enforce any of these Terms and Conditions be responsible to provide to any governmental authority, at any time, shall not in any way affect, limit or waive unless acceptable exemption certificates are provided Seller’s right thereafter to enforce and compel strict by Buyer in accordance with applicable law. Buyer compliance with every term and condition hereof. shall pay all charges for transportation and delivery and all excise, order, occupation, use or similar taxes, 7. Severability. If any provision of these Terms and duties, levies, charges or surcharges applicable to the Conditions is held to be invalid or unenforceable, such product(s) being purchased, whether now in effect invalidity or unenforceability shall not affect the validity or hereafter imposed by any governmental authority, or enforceability of the other portions hereof. foreign or domestic. 16 866-795-1586 • WWW.STONEAGETOOLS.COM TERMS AND CONDITIONS AND WARRANTY INFORMATION 8. Disputes. Seller and Buyer shall attempt in good 10. Jurisdiction and Venue. Seller and Buyer agree faith to promptly resolve any dispute arising under that the state or federal courts located within the City these Terms and Conditions by negotiations between and County of Denver, Colorado shall have sole and representatives who have authority to settle the exclusive jurisdiction over any litigation concerning any controversy. If unsuccessful, Seller and Buyer shall dispute arising under these Terms and Conditions not further attempt in good faith to settle the dispute otherwise resolved pursuant to Section 9 as well as any by nonbinding third-party mediation, with fees and alleged defects of any Products or damages sustained expenses of such mediation apportioned equally to as a result of such alleged defects. Seller and Buyer each side. Any dispute not so resolved by negotiation further agree that should any litigation be commenced or mediation may then be submitted to a court of in connection with such a dispute, it shall only be competent jurisdiction in accordance with the terms commenced in such courts. Seller and Buyer agree to hereof. These procedures are the exclusive procedures the exclusive jurisdiction of such courts and neither will for the resolution of all such disputes between the Seller raise any objection to the jurisdiction and venue of such and Buyer. courts, including as a result of inconvenience. 9. Governing Law. All sales, agreements for sale, offers 11. Attorney’s Fees. If any litigation is commenced to sell, proposals, acknowledgments and contracts between Seller and Buyer, or their personal of sale, including, but not limited to, purchase orders representatives, concerning any provision hereof, accepted by Seller, shall be considered a contract under the party prevailing in the litigation shall be entitled, the laws of the State of Colorado and the rights and in addition to such other relief that is granted, to a duties of all persons, and the construction and effect of reasonable sum as and for their attorneys’ fees and all provisions hereof shall be governed by and construed costs in such litigation or mediation. according to the laws of such state. STONEAGE TRADEMARK LIST View the list of StoneAge’s trademarks and service marks and learn how the trademarks should be used. Use of StoneAge trademarks may be prohibited, unless expressly authorized. http://www.StoneAgetools.com/trademark-list/ STONEAGE PATENT DATA View the list of StoneAge’s current U.S. patent numbers and descriptions. http://www.sapatents.com STONEAGE TERMS AND WARRANTY View StoneAge’s Terms and Warranty Conditions online. http://www.stoneagetools.com/terms http://www.stoneagetools.com/warranty 866-795-1586 • WWW.STONEAGETOOLS.COM 17 TERMS AND CONDITIONS AND WARRANTY INFORMATION WARRANTY: Warranties set forth herein extend only to End-Users, modification of the Product or use of parts not approved meaning customers acquiring, or that have previously by StoneAge will void this Limited Warranty. StoneAge acquired, a product manufactured by StoneAge reserves the right to change or improve the material and (“Product”) for their own use and not for resale, either design of the Product at any time without notice to End- directly from StoneAge Inc. (“StoneAge”) or from a User, and StoneAge is not obligated to make the same StoneAge Authorized Dealer or Reseller (“Dealer”). No improvements during warranty service to any Product warranty of any kind or nature is made by StoneAge previously manufactured. beyond those expressly stated herein. 4. WARRANTY EXCLUSIONS. This Limited Warranty 1. LIMITED WARRANTY PERIOD. Subject to does not cover, and StoneAge shall not be responsible the limitations and conditions hereinafter set forth, for the following, or damage caused by the following: StoneAge warrants its Product to be free from defects (1) any Product that has been altered or modified in any in workmanship and material for a period of one (1) year way not approved by StoneAge in advance in writing; from the date of purchase by the End-User, provided that (2) any Product that has been operated under more the end of the limited warranty period shall not be later severe conditions or beyond the rated capacity specified than eighteen (18) months from the date of shipment of for that Product; (3) depreciation or damage caused the Product to the Dealer or the End-User by StoneAge by normal wear and tear, failure to follow operation or (“Limited Warranty Period”). All replacement parts which installation instructions, misuse, negligence or lack are furnished under this Limited Warranty and properly of proper protection during storage; (4) exposure to installed shall be warranted to the same extent as the fire, moisture, water intrusion, electrical stress, insects, original Product under this Limited Warranty if, and only explosions, extraordinary weather and/or environmental if, the original parts were found to be defective within the conditions including, but not limited to lightning, natural original Limited Warranty Period covering the original disasters, storms, windstorms, hail, earthquakes, acts Product. Replacement parts are warranted for the of God or any other force majeure event; (5) damage to remainder of the original Limited Warranty Period. This any Product caused by any attempt to repair, replace, Limited Warranty does not cover any component part of or service the Product by persons other than StoneAge any Product not manufactured by StoneAge. Any such authorized service representatives; (6) costs of normal component part is subject exclusively to the component maintenance parts and services; (7) damage sustained manufacturer’s warranty terms and conditions. during unloading, shipment or transit of the Product; 2. LIMITED WARRANTY COVERAGE. StoneAge’s sole obligation under this Limited Warranty shall be, at StoneAge’s option and upon StoneAge’s inspection, to or (8) failure to perform the recommended periodic maintenance procedures listed in the Operator’s Manual accompanying the Product. repair, replace or issue a credit for any Product which is 5. REQUIRED WARRANTY PROCEDURES. To be determined by StoneAge to be defective in material or eligible for warranty service, the End-User must: (1) workmanship. StoneAge reserves the right to examine report the Product defect to the entity where the Product the alleged defective Product to determine whether this was purchased (i.e. StoneAge or the Dealer) within Limited Warranty is applicable, and final determination the Limited Warranty Period specified in this Limited of limited warranty coverage lies solely with StoneAge. Warranty; (2) submit the original invoice to establish No statement or recommendation made by a StoneAge ownership and date of purchase; and (3) make the representative, Dealer or agent to End-User shall Product available to a StoneAge authorized service constitute a warranty by StoneAge or a waiver or representative for inspection to determine eligibility modification to any of the provisions hereof or create any for coverage under this Limited Warranty. This Limited liability for StoneAge. Warranty shall not extend to any person or entity who 3. WARRANTY SERVICE PROVIDERS. Service and repair of the Product is to be performed only by StoneAge authorized service representatives, including Dealers who are authorized repair centers, with fails to provide proof of original purchase from StoneAge or a Dealer. No Product may be returned for credit or adjustment without prior written permission from StoneAge. StoneAge approved parts. Information about StoneAge authorized service representatives can be obtained through the StoneAge website at www.stoneagetools. com/service. Unauthorized service, repair or 18 866-795-1586 • WWW.STONEAGETOOLS.COM TERMS AND CONDITIONS AND WARRANTY INFORMATION 6. DISCLAIMER OF IMPLIED WARRANTIES AND OTHER REMEDIES. EXCEPT AS EXPRESSLY STATED HEREIN (AND TO THE FULLEST EXTENT ALLOWED UNDER APPLICABLE LAW), STONEAGE HEREBY DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND ANY AND ALL WARRANTIES, REPRESENTATIONS OR PROMISES AS TO THE QUALITY, PERFORMANCE OR FREEDOM FROM DEFECT OF THE PRODUCT COVERED BY THIS LIMITED WARRANTY. STONEAGE FURTHER DISCLAIMS ALL IMPLIED INDEMNITIES. 7. LIMITATION OF LIABILITY. End-User specifically acknowledges that the Product may be operated at high speeds and/or pressures, and that as such it may be inherently dangerous if not used correctly. EndUser shall familiarize itself with all operation materials provided by StoneAge and shall at all times use and require its agents, employees and contractors to use ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IT IS UNDERSTOOD THAT STONEAGE’S LIABILITY, WHETHER IN CONTRACT, IN TORT, UNDER ANY WARRANTY, IN NEGLIGENCE, OR OTHERWISE SHALL NOT EXCEED THE AMOUNT OF THE PURCHASE PRICE PAID BY THE END-USER FOR THE PRODUCT. STONEAGE’S MAXIMUM LIABILITY SHALL NOT EXCEED, AND END-USER’S REMEDY IS LIMITED TO EITHER (1) REPAIR OR REPLACEMENT OF THE DEFECTIVE WORKMANSHIP OR MATERIAL OR, AT STONEAGE’S OPTION, (2) REFUND OF THE PURCHASE PRICE, OR (3) ISSUANCE OF A CREDIT FOR THE PURCHASE PRICE, AND SUCH REMEDIES SHALL BE END-USER’S ENTIRE AND EXCLUSIVE REMEDY. YOU, THE END-USER, UNDERSTAND AND EXPRESSLY AGREE THAT THE FOREGOING LIMITATIONS ON LIABILITY ARE PART OF THE CONSIDERATION IN THE PRICE OF THE STONEAGE PRODUCT YOU PURCHASED. all necessary and appropriate safety devices, guards Some jurisdictions do not allow the limitation or and proper safe operating procedures. In no event shall exclusion of liability for certain damages, so the above StoneAge be responsible for any injuries to persons or limitations and exclusions may not apply to you. This property caused directly or indirectly by the operation Limited Warranty gives you specific legal rights, and you of the Product if End-User or any agent, employee, or may also have other rights which vary from jurisdiction contractor of End-User: (1) fails to use all necessary to jurisdiction. If any provisions of this Limited Warranty and appropriate safety devices, guards and proper is held to be invalid or unenforceable, such invalidity safe operating procedures; (2) fails to maintain in good or unenforceability shall not affect the validity or working order such safety devices and guards; (3) alters enforceability of the other portions hereof. or modifies the Product in any way not approved by StoneAge in advance in writing; (4) allows the Product to be operated under more severe conditions or beyond the rated capacity specified for the Product; or (5) otherwise negligently operates the Product. End-User shall indemnify and hold StoneAge harmless from any and all liability or obligation incurred by or against StoneAge, including costs and attorneys’ fees, to or by any person so injured. TO THE FULL EXTENT ALLOWED BY APPLICABLE LAW, STONEAGE SHALL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR PUNITIVE DAMAGES (INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF GOODWILL, DIMINUTION OF VALUE, WORK STOPPAGE, INTERRUPTION OF BUSINESS, RENTAL OF SUBSTITUTE PRODUCT, OR OTHER COMMERCIAL LOSS EVEN TO THE EXTENT SUCH DAMAGES WOULD CONSTITUTE DIRECT DAMAGES), WITH RESPECT TO THE COVERED STONEAGE PRODUCT, OR OTHERWISE IN CONNECTION WITH THIS LIMITED WARRANTY, REGARDLESS OF WHETHER STONEAGE HAS BEEN 866-795-1586 • WWW.STONEAGETOOLS.COM 19 1-866-795-1586 • www.STONEAGETOOLS.com © 2015 StoneAge, Inc. All Rights Reserved
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Language : en-US Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.6-c143 79.161424, 2017/09/22-11:52:47 Create Date : 2018:05:10 09:25:10-06:00 Metadata Date : 2018:05:10 09:25:16-06:00 Modify Date : 2018:05:10 09:25:16-06:00 Creator Tool : Adobe InDesign CC 13.1 (Windows) Instance ID : uuid:94b07785-5a26-4468-9aa0-1d62ae45eb0b Original Document ID : xmp.did:9d322ba9-59f6-4fd3-b672-f1a11ffe25b4 Document ID : xmp.id:d1a3012c-7375-0e48-8c8c-72cd3337736f Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:8cbd99a3-8746-9644-b23b-0df4cd2ba09a Derived From Document ID : xmp.did:f2a7ca45-809f-6c49-b078-0e1b2e823b79 Derived From Original Document ID: xmp.did:9d322ba9-59f6-4fd3-b672-f1a11ffe25b4 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 13.1 (Windows) History Changed : / History When : 2018:05:10 09:25:10-06:00 Format : application/pdf Producer : Adobe PDF Library 15.0 Trapped : False Page Count : 20 Creator : Adobe InDesign CC 13.1 (Windows)EXIF Metadata provided by EXIF.tools