Cisco SD2008 8 Port 10/100/1000 Gigabit Switch Quick Start Guide Small Business Unmanaged SD2008Quick
User Manual: Cisco Small Business Unmanaged SD2008
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
Quick Start Guide 1 Product Overview Side Panel 2 The power port and security slot are located on the side panels of the Switch. Thank you for choosing the Cisco 8-Port 10/100/1000 Gigabit Switch. The Switch provides non-blocking, wire speed switching for your 10, 100, and 1000 Mbps network clients. Front Panel The Port Status and System Status LEDs are located on the front panel of the Switch. Typical Installation Scenario The application diagram shown here is an example of a typical network configuration. The power port is where you will connect the power adapter. When you connect your network devices, make sure you don’t exceed the maximum cabling distances, which are listed in the following table: System—(Green) This LED lights up and remains lit when the Switch is powered on. Cisco Small Business Model SD2008 8-Port 10/100/1000 Gigabit Switch Package Contents The security slot is where you can attach a lock to protect the Switch from theft. Placement Options From To Maximum Distance Ports 1-8—(Green) Each LED lights up when a connection is made through its corresponding port. It flashes when the corresponding port is active. Set the Switch on its four rubber feet, or mount the Switch on a wall. Switch Switch 100 meters (328 feet) Back Panel The Switch offers two wall-mount slots, which are the two crisscross slots on the bottom panel. The measurement between the two slots is 2.52 inches (64 mm). Switch Computer 100 meters (328 feet) The Ethernet network ports are located on the back panel of the Switch. All ports are auto-negotiating and have automatic MDI/MDI-X crossover detection. To use the wall-mount option, follow these instructions: STEP 1 Attach two screws to the wall, 2.52 inches (64 mm) apart, so that the Switch’s wall-mount slots can line up with the two screws. STEP 2 Maneuver the Switch to insert the screws into the two slots. • SD2008 Gigabit Switch • Power Adapter • Quick Start Guide 1-8—These ports connect the Switch to network devices, such as computers. NOTE Use Category 5e Ethernet network cables for your Gigabit connections. 3 Installation ! CAUTION Make sure you use the power adapter included with the Switch. Using a different power adapter may damage the Switch. Perform the steps in this section to install the hardware. STEP 1 Make sure all of the devices you will connect to the Switch are powered off. STEP 2 Connect a Category 5 Ethernet network cable to one of the numbered ports on the Switch. Connect the other end to a computer or other network device. STEP 5 Power on the devices connected to the Switch. Each active port’s corresponding LED will light up on the Switch. Congratulations! The installation of the 10/100/1000 Gigabit Switch is complete! 4 Specifications Item Specification Model SD20008 Standards IEEE 802.3, 802.3u, 802.3x, 802.3ab Ports 8 RJ-45 10/100/1000 Mbps ports Cabling Type Cat5e LEDs System, 1 through 8 Security Feature Security Slot Dimensions WxHxD 130 x 30 x 127 mm Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Cisco, Cisco Systems, the Cisco logo, and the Cisco Systems logo are registered trademarks or trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0705R) © 2008 Cisco Systems, Inc. All rights reserved. Printed in the USA on recycled paper containing 10% postconsumer waste. 78-18820-01 Use Category 5e Ethernet network cables for your Gigabit connections. STEP 3 Repeat step 2 to connect additional devices. STEP 4 Connect the supplied power adapter to the power port on the Switch’s back panel. Plug the other end of the adapter into an electrical outlet. Where to Go From Here The following table lists the specifications for the SD2008 10/100/1000 Gigabit Ethernet Switch. 5.12" x 1.18" x 5.00" NOTE 5 Unit Weight 0.94 lbs (0.425 kg Power DC12V/1A Certification FCC Class B, CE Operating Temperature 32 to 104ºF (0 to 40ºC) Storage Temperature -40 to 158ºF (-40 to 70ºC) Operating Humidity 20 to 95%, noncondensing Storage Humidity 5 to 90%, noncondensing Resource Location Customer Support www.cisco.com/go/smallbiz End User License Agreement www.cisco.com/go/smallbiz Regulatory Compliance and Safety www.cisco.com/go/smallbiz Information Warranty Information www.cisco.com/go/smallbiz Cisco Partner Central site for Small http://www.cisco.com/web/partners/ Business sell/smb/
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 2 Page Mode : UseOutlines Format : application/pdf Title : Cisco SD2008 8-Port 10/100/1000 Gigabit Switch Quick Start Guide Producer : iText 1.4.1 (by lowagie.com) Modify Date : 2008:09:19 13:14:59Z Concept : Cisco SD2008 8-port 10%2F100%2F1000 Gigabit Switch Keywords : Doc Type : TSD Products Quick Start Creator : FrameMaker 7.2 Author : chrhull Create Date : 2008:08:28 18:59:43Z Content Type : cisco.com#US#postSales Date : 2008-11-25T05:33:59.000-08:00 Access Level : Guest,Customer,Partner Country : US Description : Ia Path : cisco.com#Products#Cisco Products#Switches#LAN Switches - Small Business#Cisco Small Business Unmanaged Switches#Cisco SD2008 8-port 10%2F100%2F1000 Gigabit Switch Language : en Secondary Concept :EXIF Metadata provided by EXIF.tools