STM3220G EVAL Evaluation Board User Manual

User Manual:

Open the PDF directly: View PDF PDF.
Page Count: 68

November 2016 DocID018499 Rev 6 1/68
1
UM1057
User manual
STM3220G-EVAL evaluation board
Introduction
The STM3220G-EVAL evaluation board is a complete demonstration and development
platform for the STM32F2 Series and includes an embedded STM32F207IGH6 high-
performance ARM®Cortex®-M3 32-bit microcontroller.
The full range of hardware features on the board is described to evaluate all peripherals
(such as USB OTG HS, USB OTG FS, Ethernet, motor control, CAN, microSD™ card,
smartcard, USART, Audio DAC, RS-232, IrDA up to version C07 of the board, SRAM, ST
MEMS, EEPROM) before developing applications. Extension headers are used to easily
connect a daughterboard or a wrapping board for any specific application.
The in-circuit ST-LINK tool provides easy JTAG and SWD interface debugging and
programming.
Figure 1. STM3220G-EVAL evaluation board
1. Picture is not contractual.
www.st.com
Contents UM1057
2/68 DocID018499 Rev 6
Contents
1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.2 Demonstration software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.3 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.4 Delivery recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2 Hardware layout and configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.1 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
2.2 Boot option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.3 Clock source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.4 Reset source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.5 Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.6 EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.7 CAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.8 RS-232 and IrDA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.9 Motor control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.10 Smartcard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.11 microSD card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.12 ST MEMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.13 Potentiometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.14 ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.15 USB OTG FS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.16 Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.17 USB OTG HS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.18 Camera module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.19 SRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2.20 Development and debug support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
2.21 Display and input devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.1 Daughterboard extension connectors CN1, 2, 3 and 4 . . . . . . . . . . . . . . 25
DocID018499 Rev 6 3/68
UM1057 Contents
3
3.2 Motor control connector CN5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.3 microSD connector CN6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3.4 Ethernet RJ45 connector CN7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3.5 USB OTG FS Micro-AB connector CN8 . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3.6 USB OTG HS Micro-AB connector CN9 . . . . . . . . . . . . . . . . . . . . . . . . . 34
3.7 CAN D-type 9-pin male connectors CN10 (CAN1 or CAN2) . . . . . . . . . . 34
3.8 Audio connector CN11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3.9 Trace debug connector CN13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.10 JTAG debug connector CN14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.11 Camera module connector CN15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
3.12 RS-232 connector CN16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
3.13 Power connector CN18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
3.14 TFT LCD connector CN19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
3.15 Smartcard connector CN20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
3.16 ST-LINK/V2 connector CN21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
3.17 Camera extension connector CN23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
3.18 STM3221G-EVAL pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Appendix A Schematics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
List of tables UM1057
4/68 DocID018499 Rev 6
List of tables
Table 1. Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Table 2. Power related jumpers and solder bridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Table 3. Boot related jumpers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Table 4. Audio related jumpers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Table 5. EEPROM related jumper and solder bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Table 6. CAN-related jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Table 7. RS-232 and IrDA related jumpers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Table 8. Motor control solder bridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Table 9. Connection between ST8024 and STM32F207IGH6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Table 10. Smartcard related jumper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Table 11. microSD card related jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Table 12. Ethernet related jumpers and solder bridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Table 13. microSD card related jumper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Table 14. Camera module related jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Table 15. SRAM related jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Table 16. Third-party toolchain support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Table 17. LCD modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Table 18. Daughterboard extension connector CN1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Table 19. Daughterboard extension connector CN2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Table 20. Daughterboard extension connector CN3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table 21. Daughterboard extension connector CN4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Table 22. Motor Control connector CN5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Table 23. microSD connector CN6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Table 24. RJ45 connector CN7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Table 25. USB OTG FS Micro-AB connector CN8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Table 26. USB OTG HS Micro-AB connector CN9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Table 27. CAN D-type 9-pin male connector CN10 (CAN1 or CAN2) . . . . . . . . . . . . . . . . . . . . . . . . 34
Table 28. Trace debugging connector CN13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Table 29. JTAG debug connector CN14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Table 30. Camera module connector CN15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Table 31. RS-232 connector CN16 with ISP support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Table 32. Smartcard connector CN20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Table 33. Camera extension connector CN23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Table 34. STM3220G-EVAL pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Table 35. Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
DocID018499 Rev 6 5/68
UM1057 List of figures
5
List of figures
Figure 1. STM3220G-EVAL evaluation board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Figure 2. Hardware layout and configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 3. STM3220G-EVAL evaluation board layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 4. Pin 1 camera plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 5. Motor Control connector CN5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 6. microSD connector CN6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 7. Ethernet RJ45 connector CN7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 8. USB OTG FS Micro-AB connector CN8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 9. USB OTG HS Micro-AB connector CN9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Figure 10. CAN D-type 9-pin male connector CN10 (CAN1 or CAN2) . . . . . . . . . . . . . . . . . . . . . . . . 34
Figure 11. Trace debug connector CN13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Figure 12. JTAG debug connector CN14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Figure 13. Camera module connector CN15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Figure 14. RS-232 connector CN16 with ISP support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Figure 15. Power supply connector CN18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Figure 16. Smartcard connector CN20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Figure 17. STM3220G-EVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Figure 18. MCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Figure 19. USB OTG HS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Figure 20. Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Figure 21. Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Figure 22. Audio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Figure 23. USB OTG FS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Figure 24. SRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Figure 25. LCD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Figure 26. RS-232 and IrDA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Figure 27. CAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Figure 28. I/O peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Figure 29. I/O expander . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Figure 30. microSD card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Figure 31. Motor control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Figure 32. Smartcard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Figure 33. JTAG and trace. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Figure 34. Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Figure 35. Extension connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Figure 36. STLINK/V2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Figure 37. 3.2” LCD module with SPI and 16-bit interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Overview UM1057
6/68 DocID018499 Rev 6
1 Overview
1.1 Features
•STM32F207IGH6 microcontroller
•16 Mbit SRAM
•1 Gbyte or more microSD card
•Boot from user Flash, system memory or SRAM
•Both ISO/IEC 14443 type A and B smartcard support
•I2C compatible serial interface 8 Kbyte EEPROM, ST MEMS and I/O expander
•IEEE 802.3-2002 compliant Ethernet connector
•Two CAN 2.0 A/B channels on the same DB connector
•RS-232 communication
•IrDA transceiver (only supported up to C07 version of the board, no more supported from
C08 version)
•USB OTG (HS and FS) with Micro-AB connector
•Inductor motor control connector
•I2S Audio DAC, stereo audio jack for headset
•3.2" 240x320 TFT color LCD with touchscreen
•4 color LEDs
•Camera module and extension connector for ST camera plug-in
•Joystick with 4-direction control and selector
•Reset, wakeup, tamper and user button
•RTC with backup battery
•Extension connector for daughterboard or wrapping board
•JTAG, SW and trace debug support
•Embedded ST-LINK/V2
•Five 5V power supply options: Power jack, USB FS connector, USB HS connector,
ST-LINK/V2 or daughterboard
•MCU consumption measurement circuit
1.2 Demonstration software
Demonstration software is preloaded in the board-mounted Flash memory for easy
demonstration of the device peripherals in standalone mode. For more information and to
download the latest version, please refer to STM3220G-EVAL demonstration software at the
www.st.com/mcu website.
1.3 Ordering information
To order the STM3220G-EVAL 0evaluation board, refer to Table 1:
DocID018499 Rev 6 7/68
UM1057 Overview
67
1.4 Delivery recommendations
Several verifications are needed before using the board for the first time to make sure that
nothing has been damaged during shipment and no components are unplugged and lost.
When the board is extracted from its plastic bag, please check that no component remains
in the bag. Main components to verify are:
1. The 25 MHz crystal (X1 and X4) may have been removed by a shock.
2. The camera connected on socket CN15 located on the right side of the board under the
JTAG connector may be unplugged. If this is the case, please refer to the note in
Section 2.18: Camera module to make sure to replug it in the correct position.
3. The microSD card may have been ejected from its connector CN6 (top left corner of the
board).
The plastic protection on the camera should be removed carefully as the connection is very
fragile.
Table 1. Ordering information
Order code Target STM32
STM3220G-EVAL STM32F207IGH6
Hardware layout and configuration UM1057
8/68 DocID018499 Rev 6
2 Hardware layout and configuration
The STM3220G-EVAL evaluation board is designed around the STM32F207IGH6
microcontroller in the UFBGA176 package. The hardware block diagram Figure 2 illustrates
the connection between STM32F207IGH6 and peripherals (Camera module, LCD, SRAM,
EEPROM, ST MEMS, USART, IrDA up to version C07 of the board, USB OTG HS, USB
OTG FS, Ethernet, Audio, CAN bus, smartcard, microSD card and motor control) and
Figure 3 locates these features on the evaluation board.
Note that for every figure (layouts and schematics) of this user manual, whenever IrDA is
indicated it is only significant for board version up to C07, since IrDA has not been
populated on latest versions of the board (so IrDA is not present from the C08 board
onwards).
DocID018499 Rev 6 9/68
UM1057 Hardware layout and configuration
67
Figure 2. Hardware layout and configuration
1. IrDA is not populated on the board from version C08 of the board.
069
670),*+
56
WUDQVFHLYHU
,U'$
WUDQVFHLYHU
6PDUWFDUG
LQWHUIDFH
9UHJXODWRU
7)7/&'
0LFUR6'
FDUG
$XGLR'$&
0&FRQWURO
FRQQHFWRU
/('V.H\
-7$*
0(06
3RWHQWLRPHWHU
6PDUWFDUG
FRQQHFWRU
,QWHJUDWHG5-
FRQQHFWRU
56
'%FRQQHFWRU
$'&
,6
*3,2
0,,50,,
86$57
,&
([WHQVLRQ
FRQQHFWRUIRU
*3,2V
3+<
86$57
&$1
&$1
WUDQVFHLYHU
&$1
'%FRQQHFWRU
0&
6',2
7UDFH
'HEXJ
27*)6 86%0LFUR$%
FRQQHFWRU
((3520
,2
H[SDQGHU
-R\VWLFN
7RXFKVFUHHQ
86%SRZHU
VZLWFK
&$1
9UHJXODWRU
9UHJXODWRU
9UHJXODWRU
'&0,
&DPHUD
PRGXOH
27*+6 86%0LFUR$%
FRQQHFWRU
86%SRZHU
VZLWFK
86%+6
3+<
'$&
)60&
65$0
67/,1.9
&DPHUDH[WHQVLRQ
FRQQHFWRU
0LFURSKRQH
$PSOLILHU
$XGLR-DFN
$'&
Hardware layout and configuration UM1057
10/68 DocID018499 Rev 6
Figure 3. STM3220G-EVAL evaluation board layout
1. IrDA is not populated on the board from version C08 of the board.
06 9
&1
0RWRUFRQWURO
&1
0LFUR6'FDUG
&1
7UDFH
&1
-7$*
8
,U'$
&1
86%27*)6
&1
86%27*+6
&1
67/,1.9
&1
&RORU/&'
&1
&DPHUDPRGXOH
&1
&DPHUDH[WHQVLRQ
FRQQHFWRU
8
-R\VWLFN
%
8VHUNH\
%
7DPSHU
&1
6PDUWFDUG
%
:DNHXS
%
5HVHW
59
3RWHQWLRPHWHU
&1
9SRZHUMDFN
&1
$XGLRMDFN
&1
86$57
&1
&$1
8
670),*+
&1
5-
FRQQHFWRU
&1&1
([WHQVLRQ
CONNECTOR $4"
DocID018499 Rev 6 11/68
UM1057 Hardware layout and configuration
67
2.1 Power supply
The STM3220G-EVAL evaluation board is designed to be powered by 5 V DC power supply
and to be protected by PolyZen from a wrong power plug-in event. It is possible to configure
the evaluation board to use any of following five sources for the power supply:
•5 V DC power adapter connected to JP18, the power jack on the board
•5 V DC power with 500 mA limitation from CN8, the USB OTG FS Micro-AB connector
•5 V DC power with 500 mA limitation from CN9, the USB OTG HS Micro-AB connector
•5 V DC power with 500 mA limitation from CN21, the ST-LINK/V2 USB connector
•5 V DC power from both CN1 and CN3, the extension connector for daughterboard
(DTB for daughterboard on silkscreen)
The power supply is configured by setting the related jumpers JP4, JP32, JP18 and JP19 as
described in Table 2.
Table 2. Power related jumpers and solder bridges
Jumper Description
JP4 Jumper reserved for future use (RFU).
Default setting: Fitted
JP32
MCU_VDD is connected to 3.3 V power when JP32 is closed and MCU current
consumption measurement can be done manually by multi-meter when JP32 is open.
Default setting: Fitted
JP18
JP18 selects one of the five possible power supply sources.
Selects the ST-LINK/V2 USB connector (CN21) power supply,
set JP18 as shown:
(Default setting)
To select power supply jack (CN18) power supply, set JP18 as
shown:
To select daughterboard connector (CN1 and CN3) power
supply, set JP18 as shown:
HS
FS
DTB
PSU
STlk
HS
FS
DTB
PSU
STlk
HS
FS
DTB
PSU
STlk
Hardware layout and configuration UM1057
12/68 DocID018499 Rev 6
Note: LED LD9 is lit when the STM3220G-EVAL evaluation board is powered by 5 V correctly.
2.2 Boot option
The STM3220G-EVAL evaluation board is able to boot from:
•Embedded User Flash
•System memory with boot loader for ISP
•Embedded SRAM for debugging
The boot option is configured by setting switch SW1 (BOOT1) and SW2 (BOOT0). The
BOOT0 can be configured also via RS-232 connector CN16.
JP18
(cont.)
To select USB OTG FS (CN8) power supply, set JP18 as shown:
To select USB OTG HS (CN9) power supply, set JP18 as shown:
To select power supply jack (CN18) power supply to both
STM3220G-EVAL and daughterboard connected on CN1 and
CN3, set JP18 as shown (daughterboard must not have its own
power supply connected)
JP19
To connect Vbat to the battery, set JP19 as shown:
To connect Vbat to 3.3 V power, set JP19 as shown: (Default setting)
Table 2. Power related jumpers and solder bridges (continued)
Jumper Description
HS
FS
DTB
PSU
STlk
HS
FS
DTB
PSU
STlk
HS
FS
DTB
PSU
STlk
321
321
Table 3. Boot related jumpers
BOOT 0 BOOT 1 Boot source
0 1 or 0 STM3220G-EVAL boots from User Flash (Default setting)
1 1 STM3220G-EVAL boots from Embedded SRAM
1 0 STM3220G-EVAL boots from System Memory
DocID018499 Rev 6 13/68
UM1057 Hardware layout and configuration
67
2.3 Clock source
Four clock sources are available on STM3220G-EVAL evaluation board for
STM32F207IGH6 and RTC embedded:
•X1, 25 MHz crystal for Ethernet PHY with socket. It can be removed when clock is
provided by MCO pin of the MCU
•X2, 26 MHz crystal for USB OTG HS PHY
•X3, 32 kHz crystal for embedded RTC
•X4, 25 MHz crystal with socket for STM32F207IGH6 microcontroller (it can be removed
from socket when internal RC clock is used)
2.4 Reset source
The reset signal of STM3220G-EVAL evaluation board is low active and the reset sources
include:
•Reset button B1
•Debugging tools from JTAG connector CN14 and trace connector CN13
•Daughterboard from CN3
•RS-232 connector CN16 for ISP
•ST-LINK/V2
2.5 Audio
The STM3220G-EVAL evaluation board enables stereo audio play and microphone
recording by an external headset connected on audio jack CN11. An audio DAC CS43L22 is
connected to the I2S2 port and the DAC channel and a microphone amplifier is connected
to ADC of the STM32F207IGH6. The CS43L22 can be configured via I2C1 and the external
PLL (U36) can provide an external clock which is connected to the I2S_CKIN pin (PC9).
Note: To avoid speaker damage it is mandatory to connect the headphone to the board on CN11
during debug of audio code. When the program is stopped on a breakpoint, a DC voltage
may be applied to the speaker which induces power consumption incompatible with the
speaker.
Warning: Signal I2S_SD (PI3) is close to signal TCK/SWCLK of the
JTAG/SWD interface, so to avoid possible communication
issues on JTAG/SWD when the I2S interface is used the
recommendations are to:
1) Prefer usage of embedded ST-LINK/V2 to external tool
connected on CN14.
2) Configure PI3 GPIO in low speed (2 MHz or 10 MHz).
Hardware layout and configuration UM1057
14/68 DocID018499 Rev 6
2.6 EEPROM
A 64 Kbit EEPROM is connected to the I2C1 bus of STM32F207IGH6.
2.7 CAN
The STM3220G-EVAL evaluation board enables two channels of CAN2.0A/B compliant
CAN bus communication based on a 3.3 V CAN transceiver on one DB9 connector (CN10).
The two CAN buses can be disconnected by jumpers from the relevant STM32F207IGH6
I/Os which are shared with FSMC and USB OTG HS.
JP3 and JP10 must be refitted to enable CAN1 or CAN2 as listed in Table 6.
High-speed, Standby and Slope Control modes can be selected by setting jumper JP7.
Table 4. Audio related jumpers
Jumper Description
JP16 Description of JP16 is in Table 11 on page 18.
JP33 The microphone amplifier can be disabled when JP33 is fitted. Default setting: Not fitted.
Table 5. EEPROM related jumper and solder bridge
Jumper Description
JP24 EEPROM is in Write Protection mode when JP24 is not fitted.
Default setting: Not fitted.
Table 6. CAN-related jumpers
Jumper Description
JP3
To connect CAN1_TX to CAN transceiver, set JP3 as shown:
To connect CAN2_TX to CAN transceiver, set JP3 as shown:
JP10
To connect CAN1_RX to CAN transceiver, set JP10 as shown:
To connect CAN2_RX to CAN transceiver, set JP10 as shown:
PD0 and PB5 are disconnected from the CAN transceiver and used for FSMC and
USB_OTG_HS when jumper JP10 is not fitted (default setting).
321
321
321
321
DocID018499 Rev 6 15/68
UM1057 Hardware layout and configuration
67
JP7
To enable the selected CAN transceiver to work in Standby mode, set JP7 as
shown:
To enable the selected CAN transceiver to work in High-speed mode, set JP7 as
shown (Default setting):
To enable the selected CAN transceiver to work in Slope Control mode, do not fit JP7.
JP9 To enable the terminal resistor for the selected CAN, fit a jumper on JP9.
(Default setting: Not fitted).
Table 6. CAN-related jumpers (continued)
Jumper Description
321
321
Hardware layout and configuration UM1057
16/68 DocID018499 Rev 6
2.8 RS-232 and IrDA
Both RS-232 and IrDA communication is enabled by D-type 9-pin RS-232 connector (CN16)
and IrDA transceiver U11 which are connected to USART3 of STM32F207IGH6 on the
STM3220G-EVAL evaluation board.
The IrDA transceiver (TFDU6300) is not populated on the STM3220G-EVAL evaluation
board from version C08. The version of the board is written on sticker placed on bottom side
of the board (ex: MB786-C08). For boards version C08 or newer it is possible to solder
manually the TDFU6300 on U11 footprint to support IRDA feature.
For ISP support, two signals are added on the RS-232 connector CN16:
•Bootloader_RESET (shared with CTS signal)
•Bootloader_BOOT0 (shared with DSR signal)
RS-232 or IrDA can be selected by setting JP22 (note that jumper JP22 position 2-3 is
unused from version C08), and ISP can be enabled by setting JP29 and JP34 as shown in
Table 7.
Table 7. RS-232 and IrDA related jumpers
Jumper Description
JP22
To connect USART3_RX to IrDA transceiver and enable IrDA communication,
set JP22 as shown (this configuration is useless on the board from version C08):
To connect USART3_RX to RS-232 transceiver and enable RS-232
communication, set JP22 as shown (Default setting):
To enable microSD card, which shares same I/Os with RS-232, JP22 is not fitted.
JP29
Bootloader_BOOT0 is managed by pin 6 of CN16 (RS-232 DSR signal) when JP29 is
closed. This configuration is used for boot loader application only.
Default setting: Not fitted.
JP34
Bootloader_RESET is managed by pin 8 of CN16 (RS-232 CTS signal) when JP34 is
fitted. This configuration is used for boot loader application only.
Default setting: Not fitted.
321
321
DocID018499 Rev 6 17/68
UM1057 Hardware layout and configuration
67
2.9 Motor control
The STM3220G-EVAL evaluation board enables a three-phase brushless motor control via
a 34-pin connector (CN5), which provides all required control and feedback signals to and
from the motor power-driving board. Available signals on this connector include emergency
stop, motor speed, 3-phase motor current, bus voltage, heatsink temperature (coming from
the motor driving board) and 6 channels of PWM control signal going to the motor driving
circuit.
The solder bridge (SB18) allows to choose two kinds of synchronization methods for PFCs
(Power Factor Correction) while the SB17 can be set for different signals on pin 31 of CN5.
The I/O pins used on motor control connector CN5 are multiplexed with some peripherals on
the board; either motor control connector or multiplexed peripherals can be enabled by the
setting of solder bridges SB10, SB11, SB12, SB14, SB15 and SB16.
Note: 1 Some 0 ohm resistors have to be removed or soldered to enable motor control application
except the solder bridges configurations mentioned above:
– R34, R58 & R51 to be removed
– R66, R204 & R205 to be soldered
2 microSD card must be removed from CN6 for motor control application.
Table 8. Motor control solder bridges
Solder
bridge Description Multiplexed
peripherals
SB18
When closed, SB18 redirects the PFC synchronized signal to timer 3
input capture pin 2 in addition to the timer 3 external trigger input.
Default setting: Open
-
SB17
For CN5 encoder signal input (pin 31), SB17 must be open.
For CN5 special motor analog signal input (pin 31), SB17 must be
closed.
Default setting: Open
-
SB16 To connect MC_EmergencySTOP to PI4, close SB16.
Default setting: Open
Camera module
connected to
CN15
SB10 To connect MC_EnIndex to PB8, close SB10.
Default setting: Open
EthernetSB11 To connect MC_CurrentA to PC1, close SB11.
Default setting: Open
SB12 To connect MC_CurrentB to PC2, close SB12.
Default setting: Open
SB14 To connect MC_EnB to PD13, close SB14.
Default setting: Open
FSMC
SB15 To connect MC_EnA to PD12 close SB15.
Default setting: Open
Hardware layout and configuration UM1057
18/68 DocID018499 Rev 6
2.10 Smartcard
STMicroelectronics smartcard interface chip ST8024 is used on STM3220G-EVAL board for
asynchronous 3 V and 5 V smartcards. It performs all supply protection and control
functions based on the connections with STM32F207IGH6 listed in Table 9:
Smartcard shares some I/Os with I2S bus for Audio. Some jumper settings need to be
reconfigured to enable smartcard as indicated below:
2.11 microSD card
The 1 GByte or more microSD card connected to SDIO of STM32F207IGH6 is available on
the board. microSD card detection is managed by the standard I/O port PH13. microSD card
shares I/Os with motor control, RS-232 and audio. The jumpers JP22 and JP16 must be
refit and motor control connector (CN5) must be disconnected for microSD card function.
Table 9. Connection between ST8024 and STM32F207IGH6
ST8024 signals Description Connect to
STM32F207IGH6
5V/3V Smartcard power supply selection pin PH15
I/OUC MCU data I/O line PC6
XTAL1 Crystal or external clock input PG7
OFF Detect presence of a card, MCU interrupt, share same
pin with motor controller PF6
RSTIN Card reset input from MCU PF7
CMDVCC Start activation sequence input (Active Low), share
same pin with I2S DAC and Motor control PG12
Table 10. Smartcard related jumper
Jumper Description
JP21
To connect Smartcard_IO to PC6, JP21must be fitted.
JP21 must not be fitted for Audio DAC connection to I2S.
Default setting: Not fitted.
Table 11. microSD card related jumpers
Jumper Description
JP22 Description of JP22 is in Section 2.8: RS-232 and IrDA
JP16
PC9 is connected to microSD card_D1 when JP16 is set as shown to the right:
(Default setting):
PC9 is connected to I2S_CKIN when JP16 is set as show to the right:
321
321
DocID018499 Rev 6 19/68
UM1057 Hardware layout and configuration
67
2.12 ST MEMS
The ST MEMS device LIS302DL is connected to I2C1 bus of STM32F207IGH6 on the
board.
2.13 Potentiometer
There is one 10 kΩ potentiometer RV1 connected to PF9 of STM32F207IGH6 on the board.
2.14 ADC
Two test points (TP3 AIN-) and (TP4 AIN+) are placed close to port PC1 of the MCU
allowing precise measurements on ADC1, ADC2 or ADC3 channel 11. As PC1 is also used
as current A input on the motor control connector it is recommended to remove R219 to
optimize noise immunity on this input.
A potentiometer RV1 is connected to PF9 of STM32F207IGH6. If needed, a low pass filter
(R74 and C59) can be placed on this input to reduce the bandwidth of the analog input PF9.
It is also possible to place the Ethernet PHY (U5) in low power mode in order to reduce the
noise induced by this high frequency peripheral. Power down pin (MII_INT in the schematic)
is connected to PB14 of the MCU, so this I/O can be to be configured as output low during
analog precision measurement.
2.15 USB OTG FS
The STM3220G-EVAL evaluation board enables USB OTG full speed communication via a
USB micro-AB connector (CN8) and USB power switch (U1) connected to VBUS. The
evaluation board can be powered by this USB connection at 5 V DC with a 500 mA current
limitation.
LED LD6 indicates that either:
•Power switch (U1) is ON and the STM3220G-EVAL functions as a USB host or
•VBUS is powered by another USB host while the STM3220G-EVAL functions as a USB
device.
LED LD5 indicates an over-current.
2.16 Ethernet
The STM3220G-EVAL evaluation board enables 10/100M Ethernet communication by a
PHY DP83848CVV (U5) and integrated RJ45 connector (CN7). Both MII and RMII interface
modes can be selected by setting jumpers JP5, JP6 and JP8 as listed below:
Hardware layout and configuration UM1057
20/68 DocID018499 Rev 6
Note: 1 A test point (TP2) is available on the board for the PTP_PPS feature test.
2 The Ethernet PHY, U5, can be powered down by regulating PB14.
3 In RMII mode it is not possible to use MCO to output the 50 MHz clock to PHY due to the
PLL limitation explained in chapter 2.6.5 of STM32F20x & STM32F21x Errata sheet
(ES0005). In such a case it is possible to provide the 50 MHz clock by soldering a 50 MHz
oscillator (ref SM7745HEV-50.0M or equivalent) on the U3 footprint located under CN3 and
also removing jumper on JP5. This oscillator is not provided with the board.
Table 12. Ethernet related jumpers and solder bridges
Jumper Description
JP8
JP8 selects MII or RMII interface mode.
To enable MII, JP8 is not fitted.
To enable RMII interface mode, JP8 is fitted.
Default setting: Not fitted.
JP6
To enable MII interface mode, set JP6 as shown (Default setting):
To enable RMII interface mode, set JP6 as shown:
JP5
To provide 25 MHz clock for MII or 50 MHz clock for RMII by MCO at PA8, set
JP5 as shown (Default setting):
To provide 25 MHz clock by external crystal X1 (for MII interface mode only) set
JP5 as shown:
When clock is provided by external oscillator U3, JP5 must not be fitted (Default setting).
SB1
SB1 selects clock source only for RMII mode.
To connect the clock from MCO to RMII_REF_CLK, close SB1.
The resistor R212 has to be removed in this case.
Default setting: Open.
321
321
321
321
DocID018499 Rev 6 21/68
UM1057 Hardware layout and configuration
67
2.17 USB OTG HS
The STM3220G-EVAL evaluation board enables USB OTG high speed communication via
a USB micro-AB connector (CN9), USB high speed PHY (U8) and USB power switch (U4)
connected to VBUS. The evaluation board can be powered by this USB connector (CN9) at
5 V DC with a 500 mA current limitation.
LED LD7 indicates that power switch (U4) is ON and the STM3220G-EVAL is working as a
USB host or that VBUS is powered by another USB host when the STM3220G-EVAL is
working as a USB device. LD8 indicates an over-current.
The USB ULPI bus is shared with CAN2 bus, JP10 and JP3 must be kept open for USB
OTG HS.
Note: On boards MB786 prior to version B03 it is possible that after a board RESET the MCU is no
longer able to control communication with the OTG PHY (U8). When this issue occurs the
only way to recover OTG PHY control is to power the board OFF and ON. This issue is fixed
on MB786 version B03 or newer.
2.18 Camera module
A camera module is connected to DCMI bus of STM32F207IGH6 and shares the same I/Os
with the motor control connector. SB16 must be kept open (default setting) for camera
module application.
There are two possible modules and omnivision cameras populated on the CN15 connector
of the board:
•1.3 Megapixel: Module CN01302H1045-C: Camera OV9655
•2 Megapixel: Module CN020VAH2554-C: Camera OV2640
Note: 1 When the camera demo loaded in Flash is executed, some green pixels may appear in high
contrast zones, depending on the image captured.
2 The camera is not firmly restricted on its connector (CN15). It is possible that during
shipment the camera could be unplugged. In such case plug it into the right position as
shown on the picture below (pin 1 dot on top left corner of the socket).
It is not recommended to remove it in order to avoid false contact later.
Table 13. microSD card related jumper
Jumper Description
JP31 To disable USB OTG PHY U8, JP31 is not fitted.
Default setting: Fitted.
Table 14. Camera module related jumpers
Jumper Description
JP26 To set power down mode for the camera module, JP26 is fitted.
Default setting: Not fitted.
SB16 Description of SB16 is in Section 2.9: Motor control.
Hardware layout and configuration UM1057
22/68 DocID018499 Rev 6
Figure 4. Pin 1 camera plug
1. Picture is not contractual
The camera extension connector CN23 is available on the boards to connect the ST camera
plug-in board.
2.19 SRAM
The 16 Mbit SRAM is connected to FSMC bus of the STM32F207IGH6 which shares the
same I/Os with CAN1 bus. JP3 and JP10 must not be fitted for SRAM and LCD application.
Table 15. SRAM related jumpers
Jumper Description
JP1
Connect PE4 to SRAM as A20 by setting JP1 as shown (Default setting):
Connect PE4 to trace connector CN13 as TRACE_D1 by setting JP1 as shown:
JP2
Connect PE3 to SRAM as A19 by settiing JP2 as shown (Default setting):
Connect PE3 to trace connector CN13 as TRACE_D0 by setting JP2 as shown:
321
321
321
321
DocID018499 Rev 6 23/68
UM1057 Hardware layout and configuration
67
2.20 Development and debug support
Version 2 of the ST-LINK, called ST-LINK/V2, is embedded on the board. This tool allows
onboard program loading and debugging of the STM32F using the JTAG or SWD interface.
Third-party debug tools are also supported by the JTAG (CN14) or Trace (CN13)
connectors.
To communicate with the embedded ST-LINK/V2, a specific driver needs to be installed on
the PC. To download and install this driver, refer to the software and development tools page
for the STM32F family available on www.st.com (the install shield is called
ST-LINK_V2_USBdriver.exe).
Third-party toolchains, Atollic TrueSTUDIO, KEIL ARM-MDK, IAR EWARM and Tasking VX-
Toolset support ST-LINK/V2 according to the following table:
The embedded ST-LINK/V2 connects to the PC via a standard USB cable from connector
CN21. The bicolor LED LD10 (COM) indicates the status of the communication as follows:
•Slow blinking Red/Off: At power-on before USB initialization
•Fast blinking Red/Off: After the first correct communication between PC and
ST-LINK/V2 (enumeration)
•Red LED On: When initialization between PC and ST-LINK/V2 is successfully finished
•Green LED On: After successful target communication initialization
•Blinking Red/Green: During communication with target
•Green On: Communication finished and OK
•Orange On: Communication failure
Note: 1 It is possible to power the board via CN21 (embedded ST-LINK/V2 USB connector) even if
an external tool is connected to CN13 (trace) or CN14 (external JTAG and SWD).
2 If the I2S interface is used, refer to the warning in Chapter 2.5.
Table 16. Third-party toolchain support
Manufacturer Toolchain Version
Atollic TrueSTUDIO 2.1
IAR EWARM 6.20.4
Keil MDK-ARM 4.20
Tasking VX-Toolset ARM Cortex-M 4.0.1
Hardware layout and configuration UM1057
24/68 DocID018499 Rev 6
2.21 Display and input devices
The 3.2” TFT color LCD connected to FSMC bus and 4 general purpose color LEDs (LD 1,
2, 3, 4) are available as display devices. A touchscreen connected to an I/O expander
(U24), 4-direction joystick with selection key, general purpose button (B4), wakeup button
(B2) and tamper detection button (B3) are available as input devices.
Table 17. LCD modules
Pin on
CN19 Pin name Pin connection Pin on
CN19 Pin name Pin connection
1 CS FSMC_NE3 (PG10) 18 PD14 FSMC_D12
2 RS FSMC_A0 19 PD15 FSMC_D13
3 WR/SCL FSMC_NWE 20 PD16 FSMC_D14
4 RD FSMC_NOE 21 PD17 FSMC_D15
5 RESET RESET# 22 BL_GND GND
6 PD1 FSMC_D0 23 BL_Control +5V
7PD2 FSMC_D1 24VDD +3V3
8PD3 FSMC_D2 25VCI +3V3
9 PD4 FSMC_D3 26 GND GND
10 PD5 FSMC_D4 27 GND GND
11 PD6 FSMC_D5 28 BL_VDD +5V
12 PD7 FSMC_D6 29 SDO NC
13 PD8 FSMC_D7 30 SDI NC
14 PD10 FSMC_D8 31 XL I/O expander U24
15 PD11 FSMC_D9 32 XR I/O expander U24
16 PD12 FSMC_D10 33 YD I/O expander U24
17 PD13 FSMC_D11 34 YU I/O expander U24
DocID018499 Rev 6 25/68
UM1057 Connectors
67
3 Connectors
3.1 Daughterboard extension connectors CN1, 2, 3 and 4
Four male headers, CN1, 2, 3 and 4, can be used to connect with a daughterboard or
standard wrapping board to STM3220G-EVAL evaluation board. A total number of 140
GPIOs are available on the board.
Each pin on CN1, 2, 3 and 4 can be used by a daughterboard after disconnecting it from the
corresponding function block on the STM3220G-EVAL evaluation board. Please refer to
tables from Table 18 to Table 21 for details.
Table 18. Daughterboard extension connector CN1
Pin Description Alternative function How to disconnect with function block on
STM3220G-EVAL board
1GND - -
3 PE3 Trace_D0 and FSMC_A19 Keep JP2 on 2<->3
5 PE5 Trace_D2 -
7 PI8 LCD_HSYNC -
9 PC14 OSC32_IN Remove R84, SB4 closed
11 PC15 OSC32_OUT Remove R85, SB5 closed
13 PI10 MII_RX_ER Remove RS3
15 PF0 FSMC_A0 -
17 PF2 FSMC_A2 -
19 GND - -
21 PF5 FSMC_A5 -
23 PF7 Smartcard_RST -
25 PF9 Potentiometer Remove R151
27 PH0 OSC_IN SB6 closed
29 PC0 ULPI_STP -
31 PC1 MII_MDC SB11 open
33 PC3 MII_TX_CLK Remove R51
35 PA0 WakeUP Remove R139
37 PA2 MII_MDIO -
39 GND - -
41 PH4 ULPI_NXT Remove R61
43 NC - -
45 NC - -
47 EMU_3V3 - -
49 EMU_5V - -
Connectors UM1057
26/68 DocID018499 Rev 6
2 PE2 Trace_CLK -
4 PE4 Trace_D1 & FSMC_A20 Keep JP1 on 2<->3
6 PE6 Trace_D3 -
8 PC13 Anti-Tamper Remove R143
10 GND - -
12 PI9 LED3 Remove R141
14 PI11 ULPI_DIR Remove R62
16 PF1 FSMC_A1 -
18 PF3 FSMC_A3 -
20 PF4 FSMC_A4 -
22 PF6 Smartcard_OFF Remove R126
24 PF8 LCD_CS -
26 PF10 Audio_IN Remove R196
28 PH1 OSC_OUT Remove R86, SB7 closed
30 GND - -
32 PC2 MII_TXD2 & MC SB12 open
34 VREF+ - -
36 PA1 MII_RX_CLK JP6 open
38 PH2 MII_CRS Remove RS3
40 PH3 MII_COL Remove RS3
42 PH5 OTG_FS_PowerSwitchOn Remove R18
44 NC - -
46 NC - -
48 APP_3V3 - -
50 GND - -
Table 19. Daughterboard extension connector CN2
Pin Description Alternative Function How to disconnect with function block on
STM3220G-EVAL board
1GND - -
3 PA3 ULPI_D0 -
5 PA5 ULPI_CLK Remove R69
7 PA7 MII_RX_DV Remove RS2, JP8 open
9 PC5 MII_RXD1 Remove R58
Table 18. Daughterboard extension connector CN1 (continued)
Pin Description Alternative function How to disconnect with function block on
STM3220G-EVAL board
DocID018499 Rev 6 27/68
UM1057 Connectors
67
11 PB0 ULPI_D1 -
13 PB2 BOOT1 -
15 PF12 FSMC_A6 -
17 PF14 FSMC_A8 -
19 GND - -
21 PG1 FSMC_A11 -
23 PE8 FSMC_D5 -
25 PE10 FSMC_D7 -
27 PE12 FSMC_D9 -
29 PE14 FSMC_D11 -
31 PE15 FSMC_D12 -
33 PB11 ULPI_D4 -
35 PH7 MII_RXD3 Remove RS3
37 PH9 DCMI_D0 Remove camera module from CN15
39 GND - -
2 APP_VCC - -
4 PA4 Audio_DAC_OUT Remove R115
6 PA6 DCMI_PIXCK Remove camera module from CN15
8 PC4 MII_RXD0 Remove RS2
10 GND - -
12 PB1 ULPI_D2 -
14 PF11 OTG_FS_Overcurrent Remove R15
16 PF13 FSMC_A7 -
18 PF15 FSMC_A9 -
20 PG0 FSMC_A10 -
22 PE7 FSMC_D4 -
24 PE9 FSMC_D6 -
26 PE11 FSMC_D8 -
28 PE13 FSMC_D10 -
30 GND - -
32 PB10 ULPI_D3 -
34 PH6 MII_RXD2 Remove RS5
36 PH8 DCMI_HSYNC & MC Remove camera module from CN15.
Disconnect motor control board from CN5.
Table 19. Daughterboard extension connector CN2 (continued)
Pin Description Alternative Function How to disconnect with function block on
STM3220G-EVAL board
Connectors UM1057
28/68 DocID018499 Rev 6
38 PH10 DCMI_D1 &MC Remove camera module from CN15.
Disconnect motor control board from CN5.
40 PH11 DCMI_D2 &MC Remove camera module from CN15.
Disconnect motor control board from CN5.
Table 20. Daughterboard extension connector CN3
Pin Description Alternative Function How to disconnect with function block on
STM3220G-EVAL board
1GND - -
3PI1 I2S_CK -
5 PH15 Smartcard_3/5V & MC Disconnect motor control board from CN5
7 PH13 microSDCard_detect & MC Remove microSD card from CN6. Disconnect
motor control board from CN5.
9 PC13 Anti-tamper Remove R143
11 RESET# Reset button -
13 PA11 OTG_FS_DM Remove R17
15 PA9 VBUS_FS Remove USB cable from CN8.
Remove R18.
17 PC9 microSDCard_D1 &
I2S_CKIN Keep JP16 on open
19 EMU_5V - -
21 PC6 I2S_MCK & Smartcard_IO JP21 open
23 PG7 Smartcard_CLK -
25 PG5 FSMC_A15 -
27 PG3 FSMC_A13 -
29 PD15 FSMC_D1 -
31 PD14 FSMC_D0 -
33 PD12 FSMC_A17 SB15 open
35 PD10 FSMC_D15 -
37 PD8 FSMC_D13 -
39 GND - -
41 PB13 ULPI_D6 & CAN2_TX -
43 PH12 DCMI_D3 & MC Remove camera module from CN15.
Disconnect motor control board from CN5.
45 NC - -
47 EMU_3V3 - -
Table 19. Daughterboard extension connector CN2 (continued)
Pin Description Alternative Function How to disconnect with function block on
STM3220G-EVAL board
DocID018499 Rev 6 29/68
UM1057 Connectors
67
49 EMU_5V - -
2 PI2 IO_Expandor_INT Remove R136
4PI0 I2S_CMD -
6 PH14 DCMI_D4 & MC Remove camera module from CN15.
Disconnect motor control board from CN5.
8 PA13 TMS/SWDIO -
10 GND - -
12 PA12 OTG_FS_DP Remove R19
14 PA10 OTG_FS_ID Remove R21
16 PA8 MCO JP5 open
18 PC8 microSDCard_D0 & MC Remove microSD card from CN6.
Disconnect motor control board from CN5.
20 PC7 LED4 Remove R140
22 PG8 LED2 Remove R154
24 PG6 LED1 Remove R155
26 PG4 FSMC_A14 -
28 PG2 FSMC_A12 -
30 GND - -
32 PD13 FSMC/MC SB14 open.
Disconnect motor control board from CN5.
34 PD11 FSMC_A16 -
36 PD9 FSMC_D14 -
38 PB15 OneNAND_INT Remove R53
40 PB14 MII_INT Remove R41
42 PB12 ULPI_D5 -
44 NC - -
46 NC - -
48 APP_3V3 - -
50 GND - -
Table 20. Daughterboard extension connector CN3 (continued)
Pin Description Alternative Function How to disconnect with function block on
STM3220G-EVAL board
Connectors UM1057
30/68 DocID018499 Rev 6
Table 21. Daughterboard extension connector CN4
Pin Description Alternative Function How to disconnect with function block on
STM3220G-EVAL board
1GND - -
3 PI6 DCMI_D6 & MC Remove camera module from CN15.
Disconnect motor control board from CN5.
5 PI4 DCMI_D5 & MC Remove camera module from CN15.
SB16 open
7 PE0 FSMC_BL0 -
9 PB8 MII_TXD3 & MC
Remove RS5
SB10 open
Disconnect motor control board from CN5.
11 BOOT0 BOOT0 -
13 PB6 I2C1_SCL Remove R103
15 PB4 TRST -
17 PG15 User button Remove R150
19 GND - -
21 PG12 Smartcard_CMDVCC &
CLD_VSYNC Remove R128
23 PG10 FSMC_NE3 Remove LCD board MB785 from CN19
25 PD7 FSMC_NE1 Remove R52
27 PD5 FSMC_NWE -
29 PD3 FSMC_CLK -
31 PD2 microSDCard_CMD -
33 PD0 FSMC_D2 & CAN1_RX JP10 open
35 PC11 microSDCard_D3 &
RS232/IrDA_RX
JP22 open
Remove microSD card from CN6
37 PA15 TDI -
39 GND - -
2 PI7 DCMI_D7 & MC Remove camera module from CN15
Disconnect motor control board from CN5
4 PI5 DCMI_VSYNC & MC Remove camera module from CN15
Disconnect motor control board from CN5
6 PE1 FSMC_BL1 -
8 PB9 I2C1_SDA Remove R111
10 GND - -
12 PB7 FSMC_NL -
14 PB5 ULPI_D7 & CAN2_RX JP10 open
16 PB3 TDO/SWO -
DocID018499 Rev 6 31/68
UM1057 Connectors
67
3.2 Motor control connector CN5
Figure 5. Motor Control connector CN5
18 PG14 MII_TXD1 Remove RS6
20 PG13 MII_TXD0 Remove RS6
22 PG11 MII_TX_EN Remove RS6
24 PG9 FSMC_NE2 Remove R47
26 PD6 FSMC_NWAIT Remove R54
28 PD4 FSMC_NOE -
30 GND - -
32 PD1 FSMC_D3 & CAN1_TX JP3 open
34 PC12 microSDCard_CLK Remove microSD card from CN6
36 PC10 microSDCard_D2 &
RS232/IrDA_TX Remove microSD card from CN6
38 PA14 TCK/SWCLK -
40 PI3 I2S_DIN -
Table 21. Daughterboard extension connector CN4 (continued)
Pin Description Alternative Function How to disconnect with function block on
STM3220G-EVAL board
Table 22. Motor Control connector CN5
Description STM32F207IGH6
pin CN5 pin CN5 pin STM32F207IGH6
pin Description
Emergency stop PI4 1 2 - GND
PWM-UH PI5 3 4 - GND
PWM-UL PH13 5 6 - GND
PWM-VH PI6 7 8 - GND
PWM-VL PH14 9 10 - GND
PWM-WH PI7 11 12 - GND
PWM-WL PH15 13 14 PC4 BUS voltage


Connectors UM1057
32/68 DocID018499 Rev 6
3.3 microSD connector CN6
Figure 6. microSD connector CN6
Phase A current PC1 15 16 - GND
Phase B current PC2 17 18 - GND
Phase C current PC3 19 20 - GND
NTC bypass relay PH8 21 22 - GND
Dissipative brake
PWM PC8 23 24 - GND
+5V power +5V 25 26 PC5 Heatsink
temperature
PFC SYNC PH10 and PH11 27 28 - VDD_Micro
PFC PWM PH12 29 30 - GND
Encoder A PD12 31 32 - GND
Encoder B PD13 33 34 PB8 Encoder Index
Table 22. Motor Control connector CN5 (continued)
Description STM32F207IGH6
pin CN5 pin CN5 pin STM32F207IGH6
pin Description
Table 23. microSD connector CN6
Pin number Description Pin number Description
1 SDIO_D2 (PC10) 5 SDIO_CLK (PC12)
2 SDIO_D3 (PC11) 6 Vss/GND
3 SDIO_CMD (PD2) 7 SDIO_D0 (PC8)
4 +3V3 8 SDIO_D1 (PC9)
- - 10 microSDCard_detect (PH13)
DocID018499 Rev 6 33/68
UM1057 Connectors
67
3.4 Ethernet RJ45 connector CN7
Figure 7. Ethernet RJ45 connector CN7
3.5 USB OTG FS Micro-AB connector CN8
Figure 8. USB OTG FS Micro-AB connector CN8
Table 24. RJ45 connector CN7
Pin
number Description Pin
number Description
1 TxData+ 2 TxData-
3 RxData+ 4 Shield
5 Shield 6 RxData-
7 Shield 8 Shield
06Y9

)URQWYLHZ
Table 25. USB OTG FS Micro-AB connector CN8
Pin number Description Pin number Description
1 VBUS (PA9) 4 ID (PA10)
2 D- (PA11) 5 GND
3D+ (PA12)- -
06Y9
&ƌŽŶƚǀŝĞǁ
Connectors UM1057
34/68 DocID018499 Rev 6
3.6 USB OTG HS Micro-AB connector CN9
Figure 9. USB OTG HS Micro-AB connector CN9
3.7 CAN D-type 9-pin male connectors CN10 (CAN1 or CAN2)
Figure 10. CAN D-type 9-pin male connector CN10 (CAN1 or CAN2)
3.8 Audio connector CN11
A 3.5 mm stereo audio jack CN11 is available on the STM3220G-EVAL board to support a
headset (headphone & microphone integrated).
Table 26. USB OTG HS Micro-AB connector CN9
Pin number Description Pin number Description
1 VBUS 4 ID
2D-5GND
3D+ - -
06Y9
&ƌŽŶƚǀŝĞǁ
Table 27. CAN D-type 9-pin male connector CN10 (CAN1 or CAN2)
Pin number Description Pin number Description
1,4,8,9 NC 7 CANH
3,5,6 GND 2 CANL
06Y9


)URQWYLHZ
DocID018499 Rev 6 35/68
UM1057 Connectors
67
3.9 Trace debug connector CN13
Figure 11. Trace debug connector CN13
3.10 JTAG debug connector CN14
Figure 12. JTAG debug connector CN14
06Y9
ϭϵϭϳϭϱϭϯϭϭϵϳϱϯϭ
ϮϬϭϴϭϲϭϰϭϮϭϬϴϲϰϮ
sŝĞǁĞĚĨƌŽŵĂďŽǀĞW
Table 28. Trace debugging connector CN13
Pin number Description Pin number Description
1 3.3 V power 2 TMS/PA13
3GND4TCK/PA14
5 GND 6 TDO/PB3
7 KEY 8 TDI/PA15
9 GND 10 RESET#
11 GND 12 TraceCLK/PE2
13 GND 14 TraceD0/PE3 or SWO/PB3
15 GND 16 TraceD1/PE4 or nTRST/PB4
17 GND 18 TraceD2/PE5
19 GND 20 TraceD3/PE6
Table 29. JTAG debug connector CN14
Pin number Description Pin number Description
1 3.3 V power 2 3.3 V power
3 PB4 4 GND
5PA156GND
7PA138GND
06Y9
ϭϵϭϳϭϱϭϯϭϭϵϳϱϯϭ
ϮϬϭϴϭϲϭϰϭϮϭϬϴϲϰϮ
sŝĞǁĞĚĨƌŽŵĂďŽǀĞW
Connectors UM1057
36/68 DocID018499 Rev 6
3.11 Camera module connector CN15
Figure 13. Camera module connector CN15
9PA1410GND
11 RTCK 12 GND
13 PB3 14 GND
15 RESET# 16 GND
17 DBGRQ 18 GND
19 DBGACK 20 GND
Table 29. JTAG debug connector CN14 (continued)
Pin number Description Pin number Description
Table 30. Camera module connector CN15
Pin number Description Pin number Description
1DGND13XCLK1
2 DGND 14 Y6(PI6)
3 SIO_D (PB9) 15 DGND
4 AVDD (2.8V) 16 Y5(PI4)
5 SIO_C (PB6) 17 PCLK (PA6)
6 RESET 18 Y4(PH14)
7 VSYNC (PI5) 19 Y0 (PH9)
8 PWDN 20 Y3(PH12)
9 HREF (PH8) 21 Y1(PH10)
10 DVDD (1.8V) 22 Y2(PH11)
11 DOVDD (2.8V) 23 AGND
12 Y7(PI7) 24 AGND
06Y9
)URQWYLHZ
DocID018499 Rev 6 37/68
UM1057 Connectors
67
3.12 RS-232 connector CN16
Figure 14. RS-232 connector CN16 with ISP support
3.13 Power connector CN18
The STM3220G-EVAL evaluation board can be powered from a 5 V DC power supply via
the external power supply jack (CN18) shown in Figure 15. The central pin of CN18 must be
positive.
Figure 15. Power supply connector CN18
3.14 TFT LCD connector CN19
One 34-pin male header CN19 is available on the board for connecting LCD module board
MB785. Please refer to Section 2.21: Display and input devices for details.
Table 31. RS-232 connector CN16 with ISP support
Pin number Description Pin number Description
1 NC 6 Bootloader_BOOT0
2 RS232_RX (PC11) 7 NC
3 RS232_TX (PC10) 8 Bootloader_RESET
4NC9NC
5GND--
06Y9


)URQWYLHZ
06Y9
'E
нϱs
Connectors UM1057
38/68 DocID018499 Rev 6
3.15 Smartcard connector CN20
Figure 16. Smartcard connector CN20
3.16 ST-LINK/V2 connector CN21
The USB type B connector CN21 is for ST-LINK/V2 connected between the
STM3220G-EVAL evaluation board and the PC for board debugging.
3.17 Camera extension connector CN23
Table 32. Smartcard connector CN20
Pin number Description Pin
number Description
1 VCC 5 GND
2RST 6 NC
3CLK7 I/O
4NC8NC
17 Card presence detection pin 18 Card presence detection pin
06Y9
)URQWYLHZ
Table 33. Camera extension connector CN23
Pin number Description Pin number Description
1+1V8 2 +1V8
3 GND 4 GND
5NC 6 NC
7 GND 8 GND
9NC10NC
11 GND 12 GND
13 SCL 14 SDA
15 Camera_Plug 16 GND
17 Camera_RST 18 NC
DocID018499 Rev 6 39/68
UM1057 Connectors
67
3.18 STM3221G-EVAL pinout
19 Camera_XSDN 20 Camera_CLK
21 GND 22 GND
23 DCMI_D0 24 DCMI_D1
25 DCMI_D2 26 DCMI_D3
27 DCMI_D4 28 DCMI_D5
29 DCMI_D6 30 DCMI_D7
31 HSYSC 32 VSYSC
33 PIXCLK 34 NC
35 NC 36 NC
37 GND 38 GND
39 +2V8 40 +2V8
Table 33. Camera extension connector CN23 (continued)
Pin number Description Pin number Description
Table 34. STM3220G-EVAL pinout
Pin no. Pin name Description
A2 PE2 TRACE_CLK / FSMC_A23
A1 PE3 TRACE_D0 / FSMC_A19
B1 PE4 TRACE_D1 / FSMC_A20
B2 PE5 TRACE_D2 / FSMC_A21
B3 PE6 TRACE_D3 / FSMC_A22
C1 VBAT VBAT
D2 PI8- ANTI TAMP2 LCD_HSYNC
D1 PC13-ANTI_TAMP ANTI-TAMPER_BUTTON
E1 PC14-OSC32_IN 32K_OSC
F1 PC15-OSC32_OUT 32K_OSC
D3 PI9 LED2
E3 PI10 ETHER_RX_ER
E4 PI11 USB_HS_DIR
F2 VSS_13 -
F3 VDD_13 -
E2 PF0 FSMC_A0
H3 PF1 FSMC_A1
H2 PF2 FSMC_A2
J2 PF3 FSMC_A3
Connectors UM1057
40/68 DocID018499 Rev 6
J3 PF4 FSMC_A4
K3 PF5 FSMC_A5
G2 VSS_5 -
G3 VDD_5 -
K2 PF6 SmartCard_OFF
K1 PF7 SmartCard_RESET
L3 PF8 LCD_CS
L2 PF9 POTENTIOMETER
L1 PF10 Audio_IN
G1 PH0 - OSC_IN OSC_IN
H1 PH1 - OSC_OUT OSC_OUT
J1 NRST RESET_BUTTON
M2 PC0 USB_HS_STP
M3 PC1 ETHER_MDC / MC_ADC123_11 pin 15 (Current A)
M4 PC2 ETHER_TXD2 / MC_ADC123_1 2 pin 17 (Current B)
M5 PC3 ETHER_TX_CLK / MC_ADC123_13 pin 19 (Current C)
M1 VSSA -
N1 VREF- -
P1 VREF+ -
R1 VDDA -
N3 PA0-WKUP WAKEUP_BUTTON
N2 PA1 ETHER_RX_CLK
P2 PA2 ETHER_MDIO
F4 PH2 ETHER_CRS
G4 PH3 ETHER_COL
H4 PH4 USB_HS_NXT
J4 PH5 USB_FS_POWER_ON
R2 PA3 USB_HS_D0
L4 BYPASS BYPASS
K4 VDD_4 -
N4 PA4 Audio_DAC_OUT
P4 PA5 USB_HS_CK
P3 PA6 CAM_PIXCK
R3 PA7 ETHER_DV
N5 PC4 ETHER_RXD0 / MC_ADC12_14 pin 14 (Bus voltage)
Table 34. STM3220G-EVAL pinout (continued)
Pin no. Pin name Description
DocID018499 Rev 6 41/68
UM1057 Connectors
67
P5 PC5 ETHER_RXD1 / MC_ADC12_15 pin 26 (Heatsink
temperature)
R5 PB0 USB_HS_D1
R4 PB1 USB_HS_D2
M6 PB2 BOOT1 /
R6 PF11 USB_FS_OVERCURRENT
P6 PF12 FSMC_A6
M8 VSS6 -
N8 VDD_6 -
N6 PF13 FSMC_A7
R7 PF14 FSMC_A8
P7 PF15 FSMC_A9
N7 PG0 FSMC_A10
M7 PG1 FSMC_A11
R8 PE7 FSMC_D4
P8 PE8 FSMC_D5
P9 PE9 FSMC_D6
M9 VSS_7 -
N9 VDD_7 -
R9 PE10 FSMC_D7
P10 PE11 FSMC_D8
R10 PE12 FSMC_D9
N11 PE13 FSMC_D10
P11 PE14 FSMC_D11
R11 PE15 FSMC_D12
R12 PB10 USB_HS_D3
R13 PB11 ULPI_D4
M10 VCAP1 VCAP / 1.2V
N10 VDD_1 -
M11 PH6 ETHER_RXD2
N12 PH7 ETHER_RXD3
M12 PH8 CAM_HSYNC / MC_NTC_bypass
M13 PH9 CAM_D0
L13 PH10 CAM_D1 / MC_TIM5_ETR pin 27 (PFC SYNC)
L12 PH11 CAM_D2 / MC_TIM3_CH2 pin 27 (PFCSYNC)
Table 34. STM3220G-EVAL pinout (continued)
Pin no. Pin name Description
Connectors UM1057
42/68 DocID018499 Rev 6
K12 PH12 CAM_D3 / TIM5_CH3 pin 29 (PFCPWM)
H12 VSS_14 -
J12 VDD_14 -
P12 PB12 ULPI_D5
P13 PB13 ULPI_D6 / CAN2_TX
R14 PB14 ETHER_INT
R15 PB15 OneNAND_INT
P15 PD8 FSMC_D13
P14 PD9 FSMC_D14
N15 PD10 FSMC_D15
N14 PD11 FSMC_A16
N13 PD12 FSMC_A17 / MC_TIM4_CH2 pin 33 (EnB)
M15 PD13 FSMC_A18 / MC_TIM4_CH2 pin 33 (EnB)
J13 VDD_8 -
M14 PD14 FSMC_D0
L14 PD15 FSMC_D1
L15 PG2 FSMC_A12
K15 PG3 FSMC_A13
K14 PG4 FSMC_A14
K13 PG5 FSMC_A15
J15 PG6 LED0
J14 PG7 SmartCard_CK
H14 PG8 LED1
G12 VSS_9 -
H13 VDD_9 -
H15 PC6 SmartCard_IO / Audio_I2S_ MCK
G15 PC7 LED3
G14 PC8 SDIO_D0/ MC_TIM3_CH3 pin23 (Dissipative Brake)
F14 PC9 SDIO_D1 I2S_CKIN
F15 PA8 MCO
E15 PA9 USB_FS_VBUS
D15 PA10 USB_FS_ID
C15 PA11 USB_FS_DM
B15 PA12 USB_FS_DP
A15 PA13 JTAG_TMS
Table 34. STM3220G-EVAL pinout (continued)
Pin no. Pin name Description
DocID018499 Rev 6 43/68
UM1057 Connectors
67
F13 VCAP2 VCAP / 1.2V
F12 VSS 2 -
G13 VDD_2 -
E12 PH13 MC_TIM8_CH1N pin 5 (UL) / microSDCard_detect
E13 PH14 CAM_D4 / MC_TIM8_CH2N pin 9 (VL)
D13 PH15 MC_TIM8_CH3N pin 13 (WL) / SmartCard_3/5V
E14 PI0 Audio_I2S_WS
D14 PI1 Audio_I2S_CK
C14 PI2 Expander_INT
C13 PI3 Audio_I2S_DOUT
D9 VSS_15 -
C9 VDD_15 -
A14 PA14 JTAG_TCK
A13 PA15 JTAG_TDI
B14 PC10 SDIO_D2 / RS232_TX
B13 PC11 SDIO_D3 / RS232_RX
A12 PC12 SDIO_CK
B12 PD0 FSMC_D2 / CAN1_RX
C12 PD1 FSMC_D3 / CAN1_TX
D12 PD2 SDIO_CMD
D11 PD3 FSMC_CLK
D10 PD4 FSMC_NOE
C11 PD5 FSMC_NWE
D8 VSS_10 -
C8 VDD_10 -
B11 PD6 FSMC_NWAIT
A11 PD7 FSMC_NE1
C10 PG9 FSMC_NE2
B10 PG10 FSMC_NE3
B9 PG11 ETHER_TXEN
B8 PG12 SmartCard_CMDVCC
A8 PG13 ETHER_TXD0
A7 PG14 ETHER_TXD1
D7 VSS_11 -
C7 VDD_11 -
Table 34. STM3220G-EVAL pinout (continued)
Pin no. Pin name Description
Connectors UM1057
44/68 DocID018499 Rev 6
B7 PG15 USER_BUTTON
A10 PB3 JTAG_TDO
A9 PB4 JTAG_TRST
A6 PB5 CAN2_RX / ETHER_PPS_OUT / ULPI_D7
B6 PB6 I2C1_SCL
B5 PB7 FSMC_NL
D6 BOOT0 BOOT0
A5 PB8 ETHER_TXD3 / MC_TIM4_CH3 pin 34 (Index)
B4 PB9 I2C1_SDA
A4 PE0 FSMC_NBL0
A3 PE1 FSMC_NBL1
D5 VSS_SA -
C6 VDD_3 POR Disable
C5 VDD_SA -
D4 PI4 CAM_D5 / MC_TIM8_BKIN pin 1 (Stop)
C4 PI5 CAM_VSYNC / MC_TIM8_CH1 pin 3 (UH)
C3 PI6 CAM_D6 / MC_TIM8_CH2 pin 7 (VH)
C2 PI7 CAM_D7 / MC_TIM8_CH3 pin 11 (WH)
Table 34. STM3220G-EVAL pinout (continued)
Pin no. Pin name Description
DocID018499 Rev 6 45/68
UM1057 Schematics
67
Appendix A Schematics
Appendix A contains the schematic diagrams listed below:
•Figure 17: STM3220G-EVAL on page 46
•Figure 18: MCU on page 47
•Figure 19: USB OTG HS on page 48
•Figure 20: Camera on page 49
•Figure 21: Ethernet on page 50
•Figure 22: Audio on page 51
•Figure 23: USB OTG FS on page 52
•Figure 24: SRAM on page 53
•Figure 25: LCD on page 54
•Figure 26: RS-232 and IrDA on page 55
•Figure 27: CAN on page 56
•Figure 28: I/O peripherals on page 57
•Figure 29: I/O expander on page 58
•Figure 30: microSD card on page 59
•Figure 31: Motor control on page 60
•Figure 32: Smartcard on page 61
•Figure 33: JTAG and trace on page 62
•Figure 34: Power on page 63
•Figure 35: Extension connector on page 64
•Figure 36: STLINK/V2 on page 65
•Figure 37: 3.2” LCD module with SPI and 16-bit interface on page 66
Schematics UM1057
46/68 DocID018499 Rev 6
Figure 17. STM3220G-EVAL
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
D D
C C
B B
A A
STMicroelectronics
Title:
Number: Rev: Sheet of
C.3(PCB.SCH)Date: 7/20/2016MB786 1 20
STM32 20-21-45-46 G-EVAL
I2S_WS
I2S_SD
I2S_SCK
Audio_SCL
Audio_SDA
Audio_RST
I2S_MCK
Audio_DAC_OUT
Audio_IN
I2S_CKIN
MCO
U_Audio
Audio.SchDoc
DCMI_PIXCK
DCMI_VSYNC
DCMI_D[0..7]
DCMI_HSYNC
Camera_RST
I2C1_SCL
I2C1_SDA
Camera_XSDN
Camera_PLUG
U_Camera connector
Camera connector.SchDoc
CAN1_TX
CAN1_RX
CAN2_TX
CAN2_RX
U_CAN
CAN.SchDoc
MII_TXD0
MII_TX_EN
MII_TX_CLK
MII_RXD0
MII_RX_ER
MII_RX_DV/RMII_CRSDV
MII_RX_CLK/RMII_REF_CLK
MII_COL
MII_CRS
MII_MDC
MII_MDIO
MCO
RESET#
MII_TXD1
MII_TXD2
MII_TXD3
MII_RXD1
MII_RXD2
MII_RXD3
MII_INT
U_Ethernet
Ethernet.SchDoc
RESET#
PA[0..15]
PB[0..15]
PC[0..15]
PD[0..15]
PE[0..15]
PF[0..15]
PG[0..15]
PH[0..15]
PI[0..11]
BOOT0
U_ExtensionConnector
ExtensionConnector.SchDoc LED4
LED3
LED1
LED2
Potentiometer
JOY_SEL
JOY_DOWN
JOY_LEFT
JOY_RIGHT
JOY_UP
Anti_Tamper
WAKEUP
User_Button
EEPROM_SCL
EEPROM_SDA
MEMS_SCL
MEMS_SDA
MEMS_INT1
MEMS_INT2
U_IO Peripherals
IO Peripherals.SchDoc
IO_Expandor_SCK
IO_Expandor_SDA
IO_Expandor_INT
TouchScreen_X+
TouchScreen_X-
TouchScreen_Y+
TouchScreen_Y-
EXP_IO2
EXP_IO3
EXP_IO4
EXP_IO5
EXP_IO6
EXP_IO7
EXP_IO8
EXP_IO9
EXP_IO10
EXP_IO11
EXP_IO12
EXP_IO1
U_IO_Expandor
IO_Expandor.SchDoc
TDI
RESET#
TRACE_D3
TRACE_D2
TRACE_D1
TRACE_D0
TRACE_CK
TRST
TMS/SWDIO
TCK/SWCLK
TDO/SWO
U_JTAG&Trace
JTAG&Trace.SchDoc
TouchScreen_X+
TouchScreen_X-
TouchScreen_Y+
TouchScreen_Y-RESET#
D[0..15]
A[0..20]
FSMC_NWE
FSMC_NOE
FSMC_NE3
LCD_VSYNC
LCD_HSYNC
LCD_CS
PC[0..15]
U_LCD
LCD.SchDoc
PA[0..15]
PB[0..15]
PC[0..15]
PD[0..15]
PE[0..15]
RESET#
Bootloader_BOOT0
Bootloader_RESET
DCMI_PIXCK
DCMI_VSYNC
DCMI_D[0..7]
DCMI_HSYNC
MCO
ULPI_D[0..7]
ULPI_CLK
ULPI_DIR
ULPI_NXT
ULPI_STP
RS232/IrDA_TX
RS232/IrDA_RX
OTG_FS_PowerSwitchOn
OTG_FS_OverCurrent
OTG_FS_DM
OTG_FS_DP
OTG_FS_ID
I2S_WS
I2S_SD
I2S_SCK
I2S_MCK
Audio_DAC_OUT
CAN1_TX
CAN1_RX
CAN2_TX
CAN2_RX
MII_TXD0
MII_TX_EN
MII_TX_CLK
MII_RXD0
MII_RX_ER
MII_RX_DV/RMII_CRSDV
MII_RX_CLK/RMII_REF_CLK
MII_COL
MII_CRS
MII_MDC
MII_MDIO
MII_TXD1
MII_TXD2
MII_TXD3
MII_RXD1
MII_RXD2
MII_RXD3
MII_INT
LED4
LED3
LED1
LED2
Potentiometer
Anti_Tamper
WAKEUP
User_Button
I2C1_SCL
I2C1_SDA
IO_Expandor_INT
TDI
TRACE_D3
TRACE_D2
TRACE_D1
TRACE_D0
TRACE_CK
TRST
TMS/SWDIO
TCK/SWCLK
TDO/SWO
D[0..15]
A[0..20]
FSMC_NE3
MicroSDCard_CLK
MicroSDCard_CMD
MicroSDCard_D0
MicroSDCard_D1
MicroSDCard_D2
MicroSDCard_D3
MicroSDCard_Detect
MC_EmergencySTOP
MC_CurrentA
MC_CurrentB
MC_CurrentC
MC_PFCsync1
MC_PFCsync2
MC_WL
MC_VH
MC_VL
MC_UH
MC_UL
MC_WH
MC_NTC
MC_DissipativeBrake
MC_PFCpwm
MC_EnA
MC_EnB
MC_HeatsinkTemperature
MC_BusVoltage
MC_EnIndex
SmartCard_3/5V
SmartCard_IO
SmartCard_RST
SmartCard_CLK
SmartCard_OFF
SmartCard_CMDVCC
FSMC_NE1
FSMC_NE2
FSMC_NWE
FSMC_NOE
FSMC_BLN0
FSMC_BLN1
FSMC_NWAIT
FSMC_CLK
FSMC_NL
OneNAND_INT
PF[0..15]
PG[0..15]
PH[0..15]
PI[0..11]
BOOT0
Audio_IN
LCD_VSYNC
LCD_HSYNC
LCD_CS
I2S_CKIN U_MCU
MCU.SchDoc
MicroSDCard_CLK
MicroSDCard_CMD
MicroSDCard_D0
MicroSDCard_D1
MicroSDCard_D2
MicroSDCard_D3
MicroSDCard_Detect
U_MicroSDCard
MicroSDCard.SchDoc
MC_EmergencySTOP
MC_CurrentA
MC_CurrentB
MC_CurrentC
MC_PFCsync1
MC_PFCsync2
MC_WL
MC_VH
MC_VL
MC_UH
MC_UL
MC_WH
MC_NTC
MC_DissipativeBrake
MC_PFCpwm
MC_EnA
MC_EnB
MC_HeatsinkTemperature
MC_BusVoltage
MC_EnIndex
U_MotorControl
MotorControl.SchDoc
U_Power
Power.SchDoc
A[0..20]
D[0..15]
FSMC_NE1
FSMC_NE2
FSMC_NWE
FSMC_NOE
FSMC_BLN0
FSMC_BLN1
FSMC_NWAIT
FSMC_CLK
FSMC_NL
OneNAND_INT
U_SRAM&OneNAND
SRAM&OneNAND.SchDoc
SmartCard_3/5V
SmartCard_IO
SmartCard_RST
SmartCard_CLK
SmartCard_OFF
SmartCard_CMDVCC
U_SmartCard
SmartCard.SchDoc
RS232/IrDA_TX
RS232/IrDA_RX
Bootloader_BOOT0
Bootloader_RESET
U_USART&IrDA
USART&IrDA.SchDoc
OTG_FS_PowerSwitchOn
OTG_FS_OverCurrent
OTG_FS_DM
OTG_FS_DP
OTG_FS_ID
U_USB_OTG_FS
USB_OTG_FS.SchDoc
ULPI_D[0..7]
ULPI_CLK
ULPI_DIR
ULPI_NXT
ULPI_STP
RESET#
U_USB_OTG_HS
USB_OTG_HS.SchDoc
R111 0
R103 0
R133
1K5
R118
1K5
+2V8
TDI
TRST
TMS/SWDIO
TCK/SWCLK
TDO/SWO
RESET#
U_ST_LINK
ST_LINK.SCHDOC
Modifications on PCB rev.C.1:
1. Add capacitor CX1.
2. Add RESET# connection on pin C4 of U8.
3. Add SB1&R212 related configuration table.
4. Change F4 MCU partnumber.
5. Remove PC12 from LCD extention connector CN22
Modifications on PCB rev.C.2:
1. Add note to highlight capacitors C33 & C50 are ceramic capacitor with low ESR.
Modifications on PCB rev.C.3:
1. Add note to remove TFDU6300 (U11) on board by default.
UM1057 Schematics
DocID018499 Rev 6 47/68
Figure 18. MCU
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
D D
C C
B B
A A
STMicroelectronics
Title:
Number: Rev: Sheet of
C.3(PCB.SCH)Date: 7/20/2016MB786 2 20
STM32 20-21-45-46 G-EVAL MCU
PA[0..15] PA[0..15]
PB[0..15] PB[0..15]
PC[0..15] PC[0..15]
PD[0..15] PD[0..15]
PE[0..15] PE[0..15]
1
4 3
2
B1
RESET
R137
do not fit
+3V3
C123
100nF
C73
20pF
C72
20pF
X4
25MHz (with socket)
R86
390
R89
10K
+3V3
2
3
1
SW2
09.03290.01
RESET#
R88 10K
+3V3
2
3
1SW1
09.03290.01
41
32
X3
MC306-G-06Q-32.768 (manufacturer JFVNY)
C71
6.8pF
C70
6.8pF
R85
0
R84
0
TP2
PTP_PPS
Bootloader_BOOT0
Bootloader_RESET
DCMI_PIXCK
DCMI_VSYNC
DCMI_D[0..7]
DCMI_HSYNC
MCO
ULPI_D[0..7]
ULPI_CLK
ULPI_DIR
ULPI_NXT
ULPI_STP
RS232/IrDA_TX
RS232/IrDA_RX
OTG_FS_PowerSwitchOn
OTG_FS_OverCurrent
OTG_FS_DM
OTG_FS_DP
OTG_FS_ID
I2S_WS
I2S_SD
I2S_SCK
I2S_MCK
Audio_DAC_OUT
CAN1_TX
CAN1_RX
CAN2_TX
CAN2_RX
MII_TXD0
MII_TX_ENMII_TX_CLK
MII_RXD0
MII_RX_ER
MII_RX_DV/RMII_CRSDV
MII_RX_CLK/RMII_REF_CLK
MII_COL
MII_CRS
MII_MDC
MII_MDIO
MII_TXD1
MII_TXD2
MII_TXD3
MII_RXD1
MII_RXD2
MII_RXD3
MII_INT
LED4
LED3
LED1
LED2
Potentiometer
Anti_Tamper
WAKEUP
User_Button
I2C1_SCL
I2C1_SDA
IO_Expandor_INT
TDI
TRACE_D3
TRACE_D2
TRACE_D1
TRACE_D0
TRACE_CK
TRST
TMS/SWDIO
TCK/SWCLK
TDO/SWO
D[0..15]
A[0..20]
FSMC_NE3
MicroSDCard_CLK
MicroSDCard_CMD
MicroSDCard_D0
MicroSDCard_D1
MicroSDCard_D2
MicroSDCard_D3
MicroSDCard_Detect
MC_EmergencySTOP
MC_CurrentA
MC_CurrentB
MC_CurrentC
MC_PFCsync1
MC_PFCsync2
MC_WL
MC_VH
MC_VL
MC_UH
MC_UL
MC_WH
MC_NTC
MC_DissipativeBrake
MC_PFCpwm
MC_EnA
MC_EnB
MC_HeatsinkTemperature
MC_BusVoltage
MC_EnIndex
SmartCard_3/5V
SmartCard_IO
SmartCard_RST
SmartCard_CLK
SmartCard_OFF
SmartCard_CMDVCC
FSMC_NE1
FSMC_NE2
FSMC_NWE
FSMC_NOE
FSMC_BLN0
FSMC_BLN1
FSMC_NWAIT
FSMC_CLK
FSMC_NL
OneNAND_INT
PE0
PE1
PE2
PE3
PE4PE5
PE6
PE7
PE8
PE9
PE10
PE11
PE12
PE13
PE14
PE15
PI0
PI1
PI2
PI3
PI4
PI5
PI6
PI7
PI8
PI9
PI10
PI11
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
PC8
PC9
PC10
PC11
PC12
PC13
PC14
PC15
PF0
PF1
PF2
PF3
PF4
PF5
PF6
PF7
PF8
PF9
PF10
PF11
PF12
PF13
PF14
PF15
A0
A1
A2
A3
A4
A5
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
PA8
PA10
PA11
PA12
PA13
PA14
PA15
PH0
PH1
PH2
PH3
PH4
PH5
PH6
PH7
PH8
PH9
PH10
PH11
PH12
PH13
PH14
PH15
ULPI_D0
ULPI_D1
ULPI_D2
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
PB8
PB9
PB10
PB11
PB12
PB13
PB14
PB15
A6
A7
A8
A9
PG0
PG1
PG2
PG3
PG4
PG5
PG6
PG7
PG8
PG9
PG10
PG11
PG12
PG13
PG14
PG15
A10
A11
ULPI_D3
DCMI_D0
DCMI_D1
DCMI_D2
DCMI_D3
PD0
PD1
PD2
PD3
PD4
PD5
PD6
PD7
PD8
PD9
PD10
PD11
PD12
PD13
PD14
PD15
D13
D14
D15
D4
D5
D6
D7
D8
D9
D10
D11
D12
A16
A17
D0
D1
A12
A13
A14
A15
DCMI_D4
D2
D3
DCMI_D5
DCMI_D6
DCMI_D7
DCMI_D[0..7]
A[0..20]
D[0..15]
ULPI_D[0..7]
VBUS_FS
PF[0..15] PF[0..15]
PG[0..15] PG[0..15]
PH[0..15] PH[0..15]
PI[0..11] PI[0..11]
JP21
BT1
CR1220 holder
L3
BEAD
C74
1uF C69
100nF
R87
47
VDDA
VDD_MCU
VREF+
C68
100nF
TP5
VREF
1
2
3
JP19
+3V3
VDD_MCU
C60
100nF
VDD_MCU
C48
100nF
C37
100nF
C35
100nF
C54
100nF
C67
100nF
C34
100nF
C57
100nF
VDD_MCU
C56
100nF
C36
100nF
C61
100nF
C66
100nF
C53
100nF
C49
100nF
C65
100nF
IOs MultiplexedIOs Multiplexed
ULPI_D4
ULPI_D5
ULPI_D6
ULPI_D7
R71
10K
C75
1uF
BOOT0
BOOT0
D1
BAT60JFILM
JP29
D2
BAT60JFILM
TP14
MCO1
TP16
CPUCK
TP15
MCO2
A18
A19
A20
Audio_IN
JP34
SB10
SB11
SB12
SB14
SB15
SB16
R34 0
R204
[N/A]
R58 0
R205
[N/A]
1
2
3
JP1
1
2
3
JP2
PE2 A2
PE3 A1
PE4 B1
PE5 B2
PE6 B3
PI8 D2
PC13
D1
PC14
E1
PC15
F1
PI9 D3
PI10 E3
PI11 E4
PF0 E2
PF1 H3
PF2 H2
PF3 J2
PF4 J3
PF5 K3
PF6 K2
PF7 K1
PF8 L3
PF9 L2
PF10 L1
PH0
G1
PH1
H1
NRST
J1
PC0
M2
PC1
M3
PC2
M4
PC3
M5
PA0
N3
PA1
N2
PA2
P2
PH2 F4
PH3 G4
PH4 H4
PH5 J4
PA3
R2
PA4
N4
PA5
P4
PA6
P3
PA7
R3
PC4
N5
PC5
P5
PB0
R5
PB1
R4
PB2
M6
PF11 R6
PF12 P6
PF13 N6
PF14 R7
PF15 P7
PG0 N7
PG1 M7
PE7 R8
PE8 P8
PE9 P9
PE10 R9
PE11 P10
PE12 R10
PE13 N11
PE14 P11
PE15 R11
PB10
R12
PB11
R13
PH6 M11
PH7 N12
PH8 M12
PH9 M13
PH10 L13
PH11 L12
PH12 K12
PB12
P12
PB13
P13
PB14
R14
PB15
R15
PD8
P15
PD9
P14
PD10
N15
PD11
N14
PD12
N13
PD13
M15
PD14
M14
PD15
L14
PG2 L15
PG3 K15
PG4 K14
PG5 K13
PG6 J15
PG7 J14
PG8 H14
PC6
H15
PC7
G15
PC8
G14
PC9
F14
PA8
F15
PA9
E15
PA10
D15
PA11
C15
PA12
B15
PA13
A15
PH13 E12
PH14 E13
PH15 D13
PI0 E14
PI1 D14
PI2 C14
PI3 C13
PA14
A14
PA15
A13
PC10
B14
PC11
B13
PC12
A12
PD0
B12
PD1
C12
PD2
D12
PD3
D11
PD4
D10
PD5
C11
PD6
B11
PD7
A11
PG9 C10
PG10 B10
PG11 B9
PG12 B8
PG13 A8
PG14 A7
PG15 B7
PB3
A10
PB4
A9
PB5
A6
PB6
B6
PB7
B5
BOOT0
D6
PB8
A5
PB9
B4
PE0 A4
PE1 A3
PI4 D4
PI5 C4
PI6 C3
PI7 C2
U16A
STM32F207IGH6
VBAT
C1
VSS F2
VDD
F3
VSS G2
VDD
G3 VREF- N1
VSSA M1
VREF+
P1
VDDA
R1
BYPASS_REG L4
VDD
K4
VSS M8
VDD
N8
VSS M9
VDD
N9
VCAP M10
VDD
N10
VSS H12
VDD
J12
VSS_SA D5
VDD
J13 VSS G12
VDD
H13
VCAP F13
VSS F12
VDD
G13
VSS D9
VDD
C9
VSS D8
VDD
C8
VSS D7
VDD
C7
RFU C6
VDD_SA
C5
U16B
STM32F207IFT6
LCD_HSYNC
LCD_VSYNC
LCD_CS
R81
10K
JP4
+3V3
1
2
3
JP16
I2S_CKIN
R51 0
R66 [N/A]
C58
4.7uF
STM32F217IGH6
STM32F407IGH6
STM32F417IGH6
Optional
- RFU means Reserved for Future Use.
- As an option, RFU could be tied to VDD or VSS for forward
compatibility with future STM32F products. However, user may leave
RFU pin connected to VDD, or VSS, or NC for STM32F2xx exclusive
use.
- JP4 should be fitted for future backward compatibility with sTM32F2xx.
C33
2.2uF
C50
2.2uF
Ceramic capacitor (Low ESR)
Schematics UM1057
48/68 DocID018499 Rev 6
Figure 19. USB OTG HS
1
1
2
2
3
3
4
4
D D
C C
B B
A A
STMicroelectronics
Title:
Number: Rev: Sheet of
C.3(PCB.SCH) Date: 7/20/2016MB786 3 20
STM32 20-21-45-46 G-EVAL USB OTG HS
ULPI_D[0..7]
ULPI_CLK
ULPI_D0
ULPI_D1
ULPI_D2
ULPI_D3
ULPI_DIR
ULPI_NXT
ULPI_STP
C44
4.7uF
+5V
R32
10K
+3V3
R28
330
12
LD7
Green
12
LD8
Red
R29
620
C25
4.7uF
GND
2
IN
5
EN
4OUT 1
FAULT 3
U4
STMPS2141STR@54
R50
12K[1%]
VBUS
1
DM
2
DP
3
ID
4
GND
5
Shield
0
USB_Micro-AB receptacle
CN9
475900001
VBUS_HS
C24
0.1uF
PI11
PC0
PH4
PA3
PA5
PB0
PB1
PB10
+3V3
C39
0.1uF
C29
0.1uF
C43
0.1uF
C42
0.1uF
C31
4.7uF
C26
0.1uF
C40
33pF
X2
26MHz
R55
1M
C41
33pF
ULPI_D[0..7]
PB11
PB12
PB13
PB5
ULPI_D4
ULPI_D5
ULPI_D6
ULPI_D7
R31
10K
R46 2K2
R61 0
R62 0
R69 0
GND D2
GND C5
PSW_N D4
VBUS F4
ID D3
VCC F3
DP D1
DM C1
RESET_N
C4
FAULT E2
NXT
D5
DIR
E5
STP
D6
CLOCK
A4
VCC(I/O) B2
D7
C6
D6
B6
D5
A6
D4
A5
D3
A3
D2
A2
D1
A1
D0
B1
VCC(I/O) B5
XTAL2
F6
XTAL1
F5
REG1V8 E6
REG_3V3 E3
RREF C2
CFG0 E1
NC F1
NC F2
GND E4
CFG1 B4
CFG2 B3
CHIP_SEL_N
C3
U8
ISP1705AET
+3V3
R72
[N/A]
+3V3
R70
100K
JP31
+3V3
+3V3
C46
0.1uF
C47
0.1uF
C64
0.1uF
C131
0.1uF
A1
A2
B1
B2
U10
USBULC6-2F3
A1
A2
B1
B2
U12
ESDA14V2-2BF3
3
2
1
T3
9013
R207
47K
R206
[N/A]
+3V3
RESET#
UM1057 Schematics
DocID018499 Rev 6 49/68
Figure 20. Camera
1
1
2
2
3
3
4
4
D D
C C
B B
A A
STMicroelectronics
Title:
Number: Rev: Sheet of
C.3(PCB.SCH) Date: 7/20/2016MB786 4 20
STM32 20-21-45-46 G-EVAL Camera
DCMI_PIXCK
DCMI_VSYNC
DCMI_D[0..7]
DCMI_HSYNC
Camera_RST
EN
1GND 2
OUT 3
VCC
4
U27
SM7745HEW-24.0M
+2V5
R130
10K
DCMI_D[0..7] DCMI_D0
DCMI_D1
DCMI_D2
DCMI_D3
DCMI_D4
DCMI_D5
DCMI_D6
DCMI_D7
R108
10K
+2V8
C90
0.1uF
I2C1_SCL
I2C1_SDA
Camera_CLK
C84
0.1uF
DGND 1
DGND 2
SIO_D
3
AVDD(2.8V) 4
SIO_C
5
RESET
6
VSYNC
7
PWDN
8
HREF
9
DVDD(1.8V) 10
DOVDD(2.8V) 11
Y7
12
XCLK1
13
Y6
14
DGND 15
Y5
16
PCLK
17
Y4
18
Y0
19
Y3
20
Y1
21
Y2
22
AGND 23
AGND 24
CN15
24-5805-024-000-829+
+2V8
JP26
C85
0.1uF
+1V8
+2V8
PH8
PI5
PA6
PB9
PB6
PH9
PH10
PH11
PH12
PI4
PH14
PI6
PI7
+2V8
R109
10K
1 2
3 4
5 6
7 8
9 10
11 12
13 14
15 16
17 18
19 20
21 22
23 24
25 26
27 28
29 30
31 32
33 34
35 36
37 38
39 40
CN23
CLM-120-02-L-D
+1V8 +1V8
SCL
SDA
SCL SDA
Camera_CLK
DCMI_D0 DCMI_D1
DCMI_D2 DCMI_D3
DCMI_D4 DCMI_D5
DCMI_D6 DCMI_D7
HSYSC
VSYSC
PIXCLK
HSYSC VSYSC
PIXCLK
+2V8 +2V8
C151
0.1uF
C152
0.1uF
C150
0.1uF
C149
0.1uF
Camera_RST
Camera_RST
Camera_XSDN
+2V8
R213
10K
Camera_PLUG
Schematics UM1057
50/68 DocID018499 Rev 6
Figure 21. Ethernet
1
1
2
2
3
3
4
4
D D
C C
B B
A A
STMicroelectronics
Title:
Number: Rev: Sheet of
C.3(PCB.SCH) Date: 7/20/2016MB786 5 20
STM32 20-21-45-46 G-EVAL Ethernet
MII_TXD0
MII_TX_EN
MII_TX_CLK
MII_RXD0
MII_RX_ER
MII_RX_DV/RMII_CRSDV
MII_RX_CLK/RMII_REF_CLK
MII_COL
MII_CRS
MII_MDC
MII_MDIO
X1
25MHz (with socket)
C14
22pF
C15
22pF
1
2
3
JP5
MCO
EN
1GND 2
OUT 3
VCC
4
U3
SM7745HEV-50.0M (do not fit)
+3V3
R26
10K
RESET#
R24
0
JP8
R40
2K2
+3V3
+3V3
R25
4.87K
R30 2K2
+3V3
R33 2K2
C21
0.1uF
C17
0.1uF
C19
0.1uF
C13
10uF
R42
2K2
MII_TXD1
MII_TXD2
MII_TXD3
MII_RXD1
MII_RXD2
MII_RXD3
TX_CLK
1
TX_EN
2
TXD_0
3
TXD_1
4
TXD_2
5
TXD_3/SNI_MODE
6
PWR_DOWN/INT
7
NC 8
NC 9
NC 10
NC 11
NC 12
RD- 13
RD+ 14
AGND 15
TD- 16
TD+ 17
PFBIN1
18
AGND 19
NC 20
NC 21
AVDD33 22
PFBOUT
23
RBIAS
24
25MHz_OUT
25
LED_ACT/COL/AN_EN 26
LED_SPEED/AN1 27
LED_LINK/AN0 28
RESET_N
29
MDIO
30 MDC
31
IOVDD33 32
X2
33
X1
34
IOGND 35
DGND 36
PFBIN2
37
RX_CLK
38 RX_DV/MII_MODE
39
CRS/CRS_DV/LED_CFG
40
RX_ER/MDIX_EN
41
COL/PHYAD0
42
RXD_0/PHYAD1
43
RXD_1/PHYAD2
44
RXD_2/PHYAD3
45
RXD_3/PHYAD4
46
IOGND 47
IOVDD33 48
U5
DP83848CVV
+3V3
C16
0.1uF
C27
0.1uF
C20
0.1uF
+3V3
R43
1.5K
1
2
3
JP6
TP1
25MHz
TD+
1
TCT
4
TD-
2
RD+
3
RCT
5
RD-
6
NC
7
CHS GND
8
LED(green)_A
9
LED(green)_K
10
LED(Yellow)_A
12
LED(Yellow)_K
11
Shield
13
Shield
14
CN7
J0011D21B
R22
240
R1
240
+3V3
C7
0.1uF
C6
0.1uF
+3V3
MII_INT R41 0
R44 0 Second source: SI-60116-F
RS5
51
RS3
51
RS6
51
+3V3
Unused in RMII mode
RS1
2K2
RS4
51
RS2
51
PI10
PC1
PC2
PC3
PA1
PA2
PH2
PH3
PA7
PC4
PC5
PG11
PH6
PH7
PG13
PG14
PB14
PB8
PA8
SB1
R208
51
R212
150
STM324xG-EVAL
STM322xG-EVAL
SB1 R212
Close
Open
Not fitted
150ohm
Board configuration
UM1057 Schematics
DocID018499 Rev 6 51/68
Figure 22. Audio
1
1
2
2
3
3
4
4
D D
C C
B B
A A
STMicroelectronics
Title:
Number: Rev: Sheet of
C.3(PCB.SCH) Date: 7/20/2016MB786 6 20
STM32 20-21-45-46 G-EVAL Audio
I2S_WS
I2S_SD
I2S_SCK
R134
10K
Audio_SCL
Audio_SDA
R110
51
1
2
U19
KSS-1508 or KSSG1708
Audio_RST
I2S_MCK
+5V
I2C address 0x94
C87
1uF (X7R)
C95
1uF
C103
0.1uF
SDA
1
SCL
2
A0
3
SPKR_OUTA+ 4
VP 5
SPKR_OUTA- 6
SPKR_OUTB+ 7
VP 8
SPKR_OUTB- 9
-VHPFILT
10
FLYN
11
FLYP
12
+VHP
13
HP/LINE_OUTB 14
HP/LINE_OUTA 15
VA
16
AGND 17
FILT+ 18
VQ 19
TSTO
20
AIN4A 21
AIN4B 22
AIN3A 23
AIN3B 24
AIN2A 25
AIN2B 26
AFILTA 27
AFILTB 28
AIN1A 29
AIN1B 30
SPKR/HP 31
RESET
32
VL
33
VD
34
DGND
35
TSTO
36
MCLK
37
SCLK
38
SDIN
39
LRCK
40
GND/Thermal Pad
0
U23
CS43L22
C88
1uF(X7R)
C98
0.1uF
C92
0.1uF
+2V5
C104
0.1uF
+3V3
C102
1uF(X5R)
C101
1uF(X5R)
C107
150pF(COG)
C108
150pF(COG)
C94
0.1uF
C86
0.022uF
R112
51
C97
0.022uF
C93
0.1uF
From IO expandor
Audio_DAC_OUT
R122
100 R113
100K
C105
1uF(X7R)
R115
0
PB9
PB6
PC6
PI0
PI1
PI3
PA4
Audio_IN
BYP
2
GND
4
IN-
5
IN+
8
GS 9
BIAS
10
C1 14
C2 15
OUT- 16
OUT+ 17
VCC 20
STBY 21
GND
22
U33
TS472IQT
1
2
U34
KECG2740TBL[N/A]
C143
100nF
R198
0
C141
1uF
R197
1K
C144
100nF
C142
1uF
+3V3C140
1uF C145
100pF
C146
100pF
C147
0ohm
R199
100K
R196
0
PF10
R200
47
+3V3
R195
10K
JP33
2
6
4
3CN11
PJ3028B-3
R216
0
R215
0
R217
[N/A]
R218
[N/A]
Fit for Iphone headset Fit for Nokia headset
VD
1
GND
2
CLK_OUT
3
AUX_OUT
4
TST_IN
5XTO 6
XTI/REF_CLK 7
AD0/CS 8
SCL/CCLK 9
SDA/CDIN 10
U36
CS2200-CP
MCO
+3V3
C158 0.1uF
PA8
I2S_CKIN
C159
1uF
PC9 R209 0
C155
[N/A]
C154
[N/A]
X6
[N/A]
R211 0
R221
10K
+3V3
0ohm resistor mounted for DC coupling
Schematics UM1057
52/68 DocID018499 Rev 6
Figure 23. USB OTG FS
1
1
2
2
3
3
4
4
D D
C C
B B
A A
STMicroelectronics
Title:
Number: Rev: Sheet of
C.3(PCB.SCH) Date: 7/20/2016MB786 7 20
STM32 20-21-45-46 G-EVAL USB_OTG_FS
+5V
R20
10K
OTG_FS_PowerSwitchOn
OTG_FS_OverCurrent
R16
47K
+3V3
12
LD5
Red
R23
620
OTG_FS_DM
OTG_FS_DP
OTG_FS_ID
C5
4.7uF
R18 0
R21 0
R15 0
GND
2
IN
5
EN
4OUT 1
FAULT 3
U1
STMPS2141STR@54
VBUS
1
DM
2
DP
3
ID
4
GND
5
Shield
0
USB_Micro-AB receptacle
CN8
475900001
VBUS_FS
PH5
PF11
PA9
PA10
PA11
PA12
R17 22
R19 22
Dz
A2
ID A3
Pd1 B1
Pup
B2
Vbus
B3
D+in C1
Pd2 C2
D+out
C3
D-in D1
GND D2
D-out
D3
U2
EMIF02-USB03F2
R27
330
12
LD6
Green
3
2
1
T1
9013
R180
47K
+3V3
R181
[N/A]
+3V3
UM1057 Schematics
DocID018499 Rev 6 53/68
Figure 24. SRAM
1
1
2
2
3
3
4
4
D D
C C
B B
A A
STMicroelectronics
Title:
Number: Rev: Sheet of
C.3(PCB.SCH) Date: 7/20/2016
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A[0..20]
D[0..15]
FSMC_NE1
FSMC_NWE
FSMC_NOE
FSMC_NWAIT
D[0..15]
A[0..20]
R36
10K
+3V3
A0
R48
10K
C28
100nF
+3V3
R49
10K
+3V3
FSMC_CLK
FSMC_NL
WE
A1
RP
A2
DQ14 A3
Vss A4
Vss A5
DQ13 A6
DQ12 B1
DQ8 B2
DQ1 B3
OE
B4
DQ9 B5
VccCore B6
DQ7 C1
DQ4 C2
DQ11 C3
DQ10 C4
DQ3 C5
VccIO C6
DQ15 D1
A12
D2
DQ0 D3
A15
D4
DQ5 D5
DQ6 D6
CLK
E1
CE
E2
DQ2 E3
NC E4
NC E5
A9
E6
A14
F1
A13
F2
AVD
F3
A7
F4
A11
F5
A8
F6
INT
G1
A0
G2 A1
G3
NC G4
A10
G5
A6
G6
RDY
H1
A4
H2 A5
H3
A2
H4 A3
H5
NC H6
U7
KFG1216U2A-DIB6
C18
100nF
C22
100nF
+3V3
R52 0
R45
10K
+3V3
R53 0OneNAND_INT
R54 0
MB786 8 20
STM32 20-21-45-46 G-EVAL SRAM & OneNAND
PD5
PD4
PD3
PB7
PD6
PD7
PB15
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
FSMC_NE2
FSMC_BLN0
FSMC_BLN1
A0
A17
PE0
PE1
R47 0
R35
10K
+3V3
PG9
A18
A19
C30
100nF
C23
100nF
+3V3
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
A20
CY7C1071DV33-12BAXI
A4
B4
A3
B3
A2
A5
A1
A4
A0
A3
CE
B5
I/O0 B6
I/O1 C5
I/O2 C6
I/O3 D5
VCC D6
VSS D1
I/O4 E5
I/O5 F5
I/O6 F6
I/O7 G6
WE
G5
A16
E4
A15
F4
A14
F3
A13
G4
A12
G3
A11
H5
A10
H4
A9
H3
A8
H2
I/O8 B1
I/O9 C1
I/O10 C2
I/O11 D2
VCC E1
I/O12 E2
I/O13 F2
I/O14 F1
I/O15 G1
BLE
A1
BHE
B2
OE
A2
A7
D4
A6
C4
A5
C3
A17
D3 A18
H1
VSS E6
A19
G2 A20
H6
CE2 A6
U6
IS61WV102416BLL-10MLI
Not fitted
Schematics UM1057
54/68 DocID018499 Rev 6
Figure 25. LCD
1
1
2
2
3
3
4
4
D D
C C
B B
A A
STMicroelectronics
Title:
Number: Rev: Sheet of
C.3(PCB.SCH) Date: 7/20/2016
TouchScreen_X+
TouchScreen_X-
TouchScreen_Y+
TouchScreen_Y-
CS
1
RS
2
WR/SCL
3
RD
4
RESET
5
VDD
24
VCI
25
GND
26
GND
27
BL_VDD
28
BL_Control
23 BL_GND
22
PD1 6
PD2 7
PD3 8
PD4 9
PD5 10
PD6 11
PD7 12
PD8 13
PD10 14
PD11 15
PD12 16
PD13 17
PD14 18
PD15 19
PD16 20
PD17 21
SDO
29
SDI
30 XL 31
XR 32
YD 33
YU 34
CN19
3.2" LCD_connector (MB785 with AM-240320D4TOQW-T00H(R))
+3V3
+5V
MB786 9 20
STM32 20-21-45-46 G-EVAL LCD
To IO expandor
RESET#
D[0..15]
A[0..20] A[0..20]
D[0..15]
FSMC_NWE
FSMC_NOE
FSMC_NE3 D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
A0
PD5
PD4
PG10
R170 150
R171 150
R172 150
R173 150
R174 150
R175 150
R176 150
R177 150
R82 150
R161 150
R163 150
R165 150
R166 150
R167 150
R168 150
R169 150
R78 150
R119 150
R162 150
R164 150
C148
10uF
L2
BEAD
C153
100nF
L1
BEAD
LCD_HSYNC
LCD_VSYNC
LCD_CS
1 2
3 4
5 6
CN22
Header 3X2H
PC[0..15]
PC10
PC11
PC[0..15]
Reserved for LCD connector
R67 0
+3V3 R68 [N/A]
UM1057 Schematics
DocID018499 Rev 6 55/68
Figure 26. RS-232 and IrDA
1
1
2
2
3
3
4
4
D D
C C
B B
A A
STMicroelectronics
Title:
Number: Rev: Sheet of
C.3(PCB.SCH) Date: 7/20/2016
RS232/IrDA_TX
RS232/IrDA_RX
SD
5
TxD
3
GND
8
Anode (VCC2)
1
Cathode
2
RxD
4
VCC1
6
NC
7
U11
TFDU6300
R64
5
R63
47
C51
0.1uF
C52
0.1uF
+3V3
C55
4.7uF
C45
4.7uF
IrDA
3
2
1
JP22
MB786 10 20
STM32 20-21-45-46 G-EVAL RS232&IrDA
C2+
1
C2-
2V- 3
R1IN 4
R2IN 5
R3IN 6
R4IN 7
R5IN 8
T1OUT 9
T2OUT 10
T3OUT 11
T3IN
12 T2IN
13 T1IN
14
R5OUT
15 R4OUT
16 R3OUT
17 R2OUT
18 R1OUT
19 R2OUTB
20 R1OUTB
21
nSHDN 22
nEN
23
C1-
24 GND 25
VCC 26
V+ 27
C1+
28
U17
ST3241EBPR
C78
100nF
C80
100nF
C76
100nF
C77
100nF
C79
100nF
+3V3
1
6
2
7
3
8
4
9
5
CN16
DB9-male UART3 or 4
+3V3
Bootloader_BOOT0
Bootloader_RESET
PC10
PC11
RXD
TXD
CTS
DSR
TFDU6300 (U11) is not populated
on boards manufactured starting from
middle 2016 (schematics revision C.3)
Note:
Schematics UM1057
56/68 DocID018499 Rev 6
Figure 27. CAN
1
1
2
2
3
3
4
4
D D
C C
B B
A A
STMicroelectronics
Title:
Number: Rev: Sheet of
C.3(PCB.SCH) Date: 7/20/2016
CAN1_TX
CAN1_RX
D
1
GND
2
VCC
3
R
4Vref 5
CANL 6
CANH 7
RS 8
U9
SN65HVD230
+3V3
+3V3
R38
120
JP9
3
2
1
JP7
R37
10K
+3V3
C32
100nF
R39
0
CAN2_TX
CAN2_RX R60
0
R56
do not fit
Default setting: 1<->2
Default setting: Open
MB786 11 20
STM32 20-21-45-46 G-EVAL CAN
1
6
2
7
3
8
4
9
5
CN10
DB9-male CAN connector
PD1
PD0
PB13
PB5
3
2
1
JP3
3
2
1
JP10
UM1057 Schematics
DocID018499 Rev 6 57/68
Figure 28. I/O peripherals
1
1
2
2
3
3
4
4
D D
C C
B B
A A
STMicroelectronics
Title:
Number: Rev: Sheet of
C.3(PCB.SCH) Date: 7/20/2016
1 2
LD3
Red
1 2
LD2
Orange
1 2
LD4
Blue
1 2
LD1
Green
R155
510
R154
680
R141
680
R140
680
LED4
LED3
LED1
LED2
3 1
2RV1
3386P-103H[10%]
R151
0
+3V3
Potentiometer
C122
10nF
R147
10K
R146
10K
R145
10K
R144
10K
R149
10K
+2V8
C119 100nF
C128 100nF
C120 100nF
C129 100nF
C121 100nF
R159
100 COMMON
5
Selection
2
DWON
3
LEFT
1
RIGHT
4
UP
6
U32
MT008-A
R153
220K
1
43
2
B2
WKUP
C124
do not fit
+3V3
R138
100
R148
4K7
1
4 3
2
B4
USER C130
100nF
+3V3
R160
100
R142
4K7
1
4 3
2
B3
Tamper C118
100nF
+3V3
R156
100
R139
330
R150
0
R143
0
JOY_SEL
JOY_DOWN
JOY_LEFT
JOY_RIGHT
JOY_UP
Anti_Tamper
WAKEUP
User_Button
EEPROM_SCL
EEPROM_SDA
MEMS_SCL
MEMS_SDA
MEMS_INT1
MEMS_INT2
E0
1
E1
2
E2
3
VSS
4SDA 5
SCL 6
WC 7
VCC 8
U18
M24C64-RMN6TP
+3V3
R102
10K
JP24 VDD_IO
1
GND 2
Reserved
3
GND 4
GND 5
VDD
6CS 7
INT1
8
INT2
9
GND 10
Reserved 11
SDO 12
SDA
13
SCL
14
U20
LIS302DL
+2V8
R107
10K
+2V8
MB786 12 20
STM32 20-21-45-46 G-EVAL IO Peripherals
Joystick LEDs
EEPROM MEMS
BUTTON
Potentiometer
C81
100nF
C89
100nF
To IO expandor
To IO expandor
R152
1K
PG6
PG8
PI9
PC7
PC13
PA0
PG15
PF9
PB9
PB6
PB9
PB6
Schematics UM1057
58/68 DocID018499 Rev 6
Figure 29. I/O expander
1
1
2
2
3
3
4
4
D D
C C
B B
A A
STMicroelectronics
Title:
Number: Rev: Sheet of
C.3(PCB.SCH) Date: 7/20/2016MB786 13 20
STM32 20-21-45-46 G-EVAL IO_Expandor
Y- 1
INT
2
A0/Data Out
3
SCLK
4
SDAT
5
VCC
6
Data in
7
IN0 8
IN1 9
GND
10
IN2 11
IN3 12
X+ 13
Vio
14
Y+ 15
X- 16
U24
STMPE811QTR
Y- 1
INT
2
A0/Data Out
3
SCLK
4
SDAT
5
VCC
6
Data in
7
IN0 8
IN1 9
GND
10
IN2 11
IN3 12
X+ 13
Vio
14
Y+ 15
X- 16
U29
STMPE811QTR
R135
10K
+2V8
I2C device address:0x82
I2C device address:0x88
+2V8
+2V8
R116
100K
R132
100K
IO_Expandor_SCK
IO_Expandor_SDA
IO_Expandor_INT
TouchScreen_X+
TouchScreen_X-
TouchScreen_Y+
TouchScreen_Y-
EXP_IO2
EXP_IO3
EXP_IO4
EXP_IO5
EXP_IO6
EXP_IO7
EXP_IO8
EXP_IO9
EXP_IO10
EXP_IO11
EXP_IO12
EXP_IO1
R121
10K
R136 0
+2V8
R117
10K
R131
10K
+2V8
C99
100nF
C115
100nF
PB9
PB6
PI2
UM1057 Schematics
DocID018499 Rev 6 59/68
Figure 30. microSD card
1
1
2
2
3
3
4
4
D D
C C
B B
A A
STMicroelectronics
Title:
Number: Rev: Sheet of
C.3(PCB.SCH) Date: 7/20/2016
MicroSD card
MB786 14 20
STM32 20-21-45-46 G-EVAL MicroSD card
+3V3
MicroSDCard_CLK
MicroSDCard_CMD
SMS064FF or SMS128FF
1
2
3
4
5
6
7
8
SW2
9
SW1
10
CN6
PJS008-2000
MicroSDCard_D0
MicroSDCard_D1
MicroSDCard_D2
MicroSDCard_D3
MicroSDCard_Detect
R9
47K
R8
47K
R2
0
R11
47K
R10
47K
R65
47K
+3V3
PC8
PC9
PC10
PC11
PC12
PD2
PH13
Schematics UM1057
60/68 DocID018499 Rev 6
Figure 31. Motor control
1
1
2
2
3
3
4
4
D D
C C
B B
A A
STMicroelectronics
Title:
Number: Rev: Sheet of
C.3(PCB.SCH) Date: 7/20/2016
R7
3.3K
C4
1nF
+3V3
+3V3
+5V
R14
0
C3
100nF
C12
100nF
R74 0
C59
do not fit
C62
do not fit
C63
do not fit
C11
do not fit
C38
do not fit
C2
10nF
C8
do not fit
C1
do not fit
R77 0
R80 0
R12
0
R4
0
C10
do not fit
EMERGENCY STOP
1
MC-UH
3
MC_UL
5
MC_VH
7
MC_VL
9
MC_WH
11
MC_WL
13
CURRENT A
15
CURRENT C
19 CURRENT B
17
NTC BYPASS RELAY
21
DISSIPATIVE BRAKE
23
+5V POWER
25
PFC SYNC
27
PFC PWM
29
Encoder A
31
Encoder B
33
GND 2
GND 4
GND 6
GND 8
GND 10
GND 12
BUS VOLTAGE 14
GND 16
GND 18
GND 20
GND 22
GND 24
Heatsink Temperature 26
Vdd_Micro 28
GND 30
GND 32
Encoder Index 34
CN5
MC_connector
MC_EmergencySTOP
MC_CurrentA
MC_CurrentB
MC_CurrentC
MC_PFCsync1
MC_PFCsync2
MC_WL
MC_VH
MC_VL
MC_UH
MC_UL
MC_WH
MC_NTC
MC_DissipativeBrake
MC_PFCpwm
MC_EnA
MC_EnB
MC_HeatsinkTemperature
MC_BusVoltage
MC_EnIndex
R6
100K
C9
do not fit
Motor control connector
Default setting: Open
Default setting: Open
MB786 15 20
STM32 20-21-45-46 G-EVAL Motor control
R73
0
R76
0
R79
0
R13
0
R5
0
PC4
PC5
PC1
PC2
PC3
PH8
PH10
PH11
PD13
PC8
PB8
PH13
PH14
PH15
PD12
PI4
PI5
PI6
PI7
R3
0
R59 0
R57 0
TP4
AIN+
TP3
AIN-
SB17
SB18
R219
0
UM1057 Schematics
DocID018499 Rev 6 61/68
Figure 32. Smartcard
1
1
2
2
3
3
4
4
D D
C C
B B
A A
STMicroelectronics
Title:
Number: Rev: Sheet of
C.3(PCB.SCH) Date: 7/20/2016
VCC 1
RST 2
CLK 3
NC 4
GND
5
NC
6
I/O
7
NC
8
18
17CN20
C816
CLKDIV1
1
CLKDIV2
2
5V/3V
3
PGND
4
C1+
5
Vddp
6
C1-
7
Vup
8
PRES
9
PRES
10
I/O
11
AUX2
12
AUX1
13
CGND
14 CLK 15
RST 16
Vcc 17
PORADJ 18
CMDVCC 19
RSTIN 20
Vdd 21
GND 22
OFF 23
XTAL1 24
XTAL2 25
I/OUC 26
AUX1UC 27
AUX2UC 28
U31
ST8024CDR
C125 100nF
C126
100nF
C117
47uF
+5V
C127 100nF
C109
100nF
R158
100K +3V3
R157
4K7
+3V3
R129
10K
R123
10K
+3V3
C111
100nF
C114
47uF
+3V3
R124
10K
+3V3
R127 0
R126 0
R125
10K
TP11
AUX2
TP12
AUX1
SmartCard_3/5V
SmartCard_IO
SmartCard_RST
SmartCard_CLK
SmartCard_OFF
SmartCard_CMDVCC
MB786 16 20
STM32 20-21-45-46 G-EVAL Smart card
R128 0
PF7
PF6
PG7
PC6
PG12
PH15
Schematics UM1057
62/68 DocID018499 Rev 6
Figure 33. JTAG and trace
1
1
2
2
3
3
4
4
D D
C C
B B
A A
STMicroelectronics
Title:
Number: Rev: Sheet of
C.3(PCB.SCH) Date: 7/20/2016
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
CN13
FTSH-110-01-L-DV
+3V3
R97
[N/A]
R96
[N/A]
R101
[N/A]
R95
[N/A]
R98
do not fit
+3V3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
CN14
JTAG +3V3
+3V3
R105 10K
R106 10K
R99
10K
R92
[N/A]
R1040
R100do not fit
R94 0
R91 do not fit
TRACE_D3
TRACE_D2
TRACE_D1
TRACE_D0
TRACE_CK
Trace connector
JTAG connector
KEY
MB786 17 20
STM32 20-21-45-46 G-EVAL JTAG & Trace
PA13
PA14
PB3
PA15
PB4
PE6
PE5
PE4
PE3
PE2
TDI
RESET#
TRST
TMS/SWDIO
TCK/SWCLK
TDO/SWO
D8
Z5V1
RS7
22
D3
Z5V1
D4
Z5V1
D5
Z5V1
D6
Z5V1
D7
Z5V1
UM1057 Schematics
DocID018499 Rev 6 63/68
Figure 34. Power
1
1
2
2
3
3
4
4
D D
C C
B B
A A
STMicroelectronics
Title:
Number: Rev: Sheet of
C.3(PCB.SCH) Date: 7/20/2016
Vin
3
GND
1
Vout 2
U22
LD1086D2M33TR
C113
220uF
C83
10uF C82
100nF
+5V
TP7
3V3
SV
1
SG
2
CV 3
CG1 4
CG2 5
CG3 6
U25
BNX002-01
C106
10uF
E5V
TP8
5V
+5V
R93
1K
12
LD9
red
TP13
Ground
1
3
2
CN18
DC-10B Z1
SMAJ5.0A-TR C112
100nF
1
2
3
U28
ZEN056V130A24LS
+3V3
D5V
E5V
MB786 18 20
STM32 20-21-45-46 G-EVAL Power
Vin
3Vout 2
1
U21
LD1117S25TR
+5V
C91
10uF
+2V5
TP6
2V5
C96
220uF
VBUS_FS
VBUS_HS
Vin
3Vout 2
1
U30
LD1117S18TR
C116
10uF
+1V8 Vin
3Vout 2
1
U26
LD1117STR
+5V
C110
10uF
+2V8
TP9
2V8
R114
120
C100
10uF
R120
150
TP10
1V8
+3V3 VDD_MCU
JP32
1 2
3 4
5 6
7 8
9 10
JP18
Header 5X2
U5V_ST_LINK
Schematics UM1057
64/68 DocID018499 Rev 6
Figure 35. Extension connector
1
1
2
2
3
3
4
4
D D
C C
B B
A A
STMicroelectronics
Title:
Number: Rev: Sheet of
C.3(PCB.SCH) Date: 7/20/2016
RESET# RESET#
MB786 19 20
STM32 20-21-45-46 G-EVAL Extension connector
12
34
56
78
910
1112
1314
1516
1718
1920
2122
2324
2526
2728
2930
3132
3334
3536
3738
3940
CN4
21N22564-40S10B
1 2
3 4
5 6
7 8
910
11 12
13 14
15 16
17 18
19 20
21 22
23 24
25 26
27 28
29 30
31 32
33 34
35 36
37 38
39 40
41 42
43 44
45 46
47 48
49 50
CN1
21N22564-50S10B 12
34
56
78
910
1112
1314
1516
1718
1920
2122
2324
2526
2728
2930
3132
3334
3536
3738
3940
CN2
21N22564-40S10B
1 2
3 4
5 6
7 8
910
11 12
13 14
15 16
17 18
19 20
21 22
23 24
25 26
27 28
29 30
31 32
33 34
35 36
37 38
39 40
41 42
43 44
45 46
47 48
49 50
CN3
21N22564-50S10B
PA0 PA1
PA2
PA3PA4
PA5PA6
PA7
PA8
PA10PA11
PA12
PA13
PA14 PA15
PB0PB1
PB2
PB3 PB4
PB5 PB6
PB7
PB8
PB9
PB10
PB11
PB12PB13
PB14
PB15
PC0
PC1 PC2
PC3
PC4
PC5
PC6
PC7
PC8PC9
PC10 PC11
PC12
PC13
EXT_PC14
EXT_PC15
PD0
PD1 PD2
PD3
PD4 PD5
PD6 PD7
PD8
PD9PD10
PD11PD12
PD13PD14
PD15
PE0
PE1
PE2
PE3 PE4
PE5 PE6
PE7
PE8PE9
PE10PE11
PE12PE13
PE14
PE15
PF0 PF1
PF2 PF3
PF4
PF5 PF6
PF7 PF8
PF9 PF10
PF11
PF12PF13
PF14PF15
PG0
PG1
PG2PG3
PG4PG5
PG6PG7
PG8
PG9 PG10
PG11 PG12
PG13
PG14 PG15
EXT_PH0 EXT_PH1
PH2
PH3
PH4 PH5
PH6
PH7PH8
PH9PH10
PH11
PH12
PH13
PH14PH15
PI0PI1
PI2
PI3
PI4
PI5 PI6
PI7
PI8
PI9
PI10 PI11
VREF+
EMU_3V3
EMU_5V
APP_3V3
APP_VCC
PC13
RESET#
EMU_5V EMU_3V3
EMU_5V
APP_3V3
BOOT0
(Left) (Right)
(Buttom)
(Top)
PA[0..15] PA[0..15]
PB[0..15] PB[0..15]
PC[0..15] PC[0..15]
PD[0..15] PD[0..15]
PE[0..15] PE[0..15]
PF[0..15] PF[0..15]
PG[0..15] PG[0..15]
PH[0..15] PH[0..15]
PI[0..11] PI[0..11]
APP_3V3APP_VCC
EMU_5VD5V
+3V3
SB6
SB7
SB4
SB5
PH0
PH1
PC14
PC15
EXT_PH0
EXT_PH1
EXT_PC14
EXT_PC15
Close to crystal on PCB
BOOT0
BOOT0
VBUS_FS
CX1
33pF
UM1057 Schematics
DocID018499 Rev 6 65/68
Figure 36. STLINK/V2
1
1
2
2
3
3
4
4
D D
C C
B B
A A
STMicroelectronics
Title:
Number: Rev: Sheet of
C.3(PCB.SCH) Date: 7/20/2016 20 20
VBAT
1
PC13
2
PC14
3
PC15
4
OSC_IN
5
OSC_OUT
6
/RST
7
VSSA
8
VDDA
9
PA0
10
PA1
11
U2_TX
12
U2_RX
13
U2_CK
14
S1_CK
15
S1_MISO
16
S1_MOSI
17
PB0
18
PB1
19
PB2/BOOT1
20
PB10
21
VSS_1
23
VDD_1
24
PB12 25
PB11
22
S2_CK 26
S2_MISO 27
S2_MOSI 28
PA8 29
PA9 30
PA10 31
PA11 32
PA12 33
JTMS 34
VSS_2 35
VDD_2 36
JTCK 37
JTDI 38
JTDO 39
JNRST 40
PB5 41
PB6 42
PB7 43
BOOT0 44
PB8 45
PB9 46
VSS_3 47
VDD_3 48
U15
STM32F103C8T6
20pF
C139
20pF
C138
1 2
X5
8MHz +3V3
USB_DM
USB_DP
STM_RST
T_JTCK
T_JTCK
T_JTDO
T_JTDI
T_JTMS
STM_JTMS_SWDIO
STM_JTCK_SWCLK
LED_STLINK
OSC_IN
OSC_OUT
T_NRST
T_JRST
LED_STLINK
T_JTCK
T_JTDI
T_JTDO
T_NRST
T_JTMS
T_JRST
R185
4K7
R186
4K7
AIN_1
C137
100nF
R183
100K
R201
100
+3V3
+3V3
+3V3
+3V3
+3V3
+3V3
AIN_1
VCC 1
D- 2
D+ 3
GND 4
SHELL 0
SHELL 0
CN21
USB-typeB connector
USB_DM
USB_DP
+3V3
C135
100nF
C133
100nF
C136
100nF
C134
100nF
R192 10
R193 10
MCU
USB
JTAG
STM_JTMS_SWDIO
STM_JTCK_SWCLK
+3V3
U5V_ST_LINK
TDI
TRST
TMS/SWDIO
TCK/SWCLK
TDO/SWO
RESET#
SWIM_PU_CTRL
R182
100K
T_SWO
T_SWDIO_IN
T_SWDIO_IN
T_SWO
1 2
3 4
5
CN17
JTAG
R194
1.5K
R189
10K
R191
36K
2
31
T2
9013
+3V3
U5V_ST_LINK
R187
[N/A]
R188
10K
R184
100K
MCO
21
4 3
Red Yellow
LD10
HSMF-A201-A00J1
R202
100
R190
0
+3V3
MB786
STM32 20-21-45-46 G-EVAL ST-LINK/V2
Schematics UM1057
66/68 DocID018499 Rev 6
Figure 37. 3.2” LCD module with SPI and 16-bit interface
1
1
2
2
3
3
4
4
D D
C C
B B
A A
STMicroelectronics
Title:
Number: Rev: Sheet of
A.1(PCB.SCH) Date: 3/27/2009
Enable
DotClk
HSYNC
VSYNC
CS
RS
WR
RD
#RESET
SDO
SDI
VDD
PD0
PD1
PD2
PD3
PD4
PD5
PD6
PD7
PD8
PD9
PD10
PD11
PD12
PD13
PD14
PD15
PD16
PD17
YU
YD
XR
XL
VSS
1
XL 2
XR 3
YD 4
YU 5
VSS
6
IM0/ID 7
IM1 8
IM3 9
SDO
10
NC
11
SDI
12
D17 13
D16 14
D15 15
D14 16
D13 17
D12 18
D11 19
D10 20
D9 21
D8 22
D7 23
D6 24
D5 25
D4 26
D3 27
D2 28
D1 29
D0 30
CS
31
RESET
32
RS
33
WR/SCL
34
RD
35
VSYNC
36
HSYNC
37
DOTCLK
38
ENABLE
39
VCC
40
VCC
41
VSS
42
LED_K
43 LED_A
44
VSS
45
CN2
FF0245SS1
R4 0
R1 10K VDD
RP1
10K
RP2
10K
RP4
10K
PD0
PD2
PD4
PD6
PD8
PD9
PD10
PD11
PD12
PD13
PD14
PD15
PD16
PD17
Enable
DotClk
HSYNC
VSYNC
VDD
C3
1uF/50V
R3 4K7
R2 4K7
SDI
SDO
RD
RS
Soldered for Serial interface only
Soldered for i80-system 16-bit interface
The 34-pin connector to mother board for both
serial & 16bit interface. Compatible with
MB694 with Touch screen signals added on
Pin 31-34.
CS
RS
WR
RD
#RESET
VDD
BLGND
BLVDD
BL_Control
PD1
PD2
PD3
PD4
PD5
PD6
PD7
PD8
PD10
PD11
PD12
PD13
PD14
PD15
PD16
PD17
SDO
SDI
A
K
Z1
STPS1L40M C1
4.7uF/50V
L1
4.7uH(1A)
R7
10
BLGND
BLVDD
R6
100K
C2
2.2uF
R5
0
R8
do not fit
BLVDD
BL_Control
BLGND
BLGND
BLGND
AM-240320D4TOQW-T00H(R)
Vi
1
Rset 2
GND
3FB 4
NC 5
Vo 6
EN
7
SW
8
PGND
9
U1
STLD40DPMR
CS
1
RS
2
WR/SCL
3
RD
4
RESET
5
VDD
24
VCI
25
GND
26
GND
27
BL_VDD
28
BL_Control
23 BL_GND
22
PD1 6
PD2 7
PD3 8
PD4 9
PD5 10
PD6 11
PD7 12
PD8 13
PD10 14
PD11 15
PD12 16
PD13 17
PD14 18
PD15 19
PD16 20
PD17 21
SDO
29
SDI
30 XL 31
XR 32
YD 33
YU 34
CN1
3.2LCD_connector
YU
YD
XR
XL
LCD board connector to Mother board
MB785 1 1
3.2" LCD module with both SPI & 16bit interface
RP3
10K
RP6
10K
RP5
10K
PD1
PD3
PD5
PD7
DocID018499 Rev 6 67/68
UM1057 Revision history
67
Revision history
Table 35. Document revision history
Date Revision Changes
15-Apr-2011 1 Initial release.
23-May-2011 2 Updated preliminary watermarks.
26-July-2011 3
Added Section 1.4: Delivery recommendations.
Updated Section 2.16: Ethernet, Section 2.17: USB OTG HS and
Section Appendix A: Schematics.
07-Oct-2011 4
Updated Table 2 JP4 description, Table 5 JP24 description and
Section Appendix A: Schematics. Added warning in Chapter 2.5 and
note in Chapter 2.20.
09-Jan-2012 5 Added note in Chapter 2.5 and updated Section Appendix A:
Schematics.
02-Nov-2016 6
Added comment IrDA is only supported up to C07 version of the
board.
Figure 17 to Figure 37 updated.
UM1057
68/68 DocID018499 Rev 6
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on
ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or
the design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2016 STMicroelectronics – All rights reserved

Navigation menu