SeL_207_XL_INST_1_plain Sunvic Sp2 Programmer Select 207

User Manual: Sunvic-sp2-Programmer Select 207

Open the PDF directly: View PDF .
Page Count: 8

Download
Open PDF In Browser	View PDF

http://waterheatertimer.org/Woods-timers-and-manuals.html#Noma-Garrison
Programmers allow you to set ‘On’ and ‘Off’ time periods. Some models switch the central heating and
domestic hot water on and off at the same time, while others allow the domestic hot water and heating to
come on and go off at different times.
Set the ‘On’ and ‘Off’ time periods to suit your own lifestyle. On some programmers you must also set
whether you want the heating and hot water to run continuously, run under the chosen ‘On’ and ‘Off’ heating
periods, or be permanently off.
The time on the programmer must be correct. Some types have to be adjusted in spring and autumn at the
changes between Greenwich Mean Time and British Summer Time.
You may be able to temporarily adjust the heating programme, for example, ‘Override’, ‘Advance’ or ‘Boost’.
These are explained in the manufacturer’s instructions.
The heating will not work if the room thermostat has switched the heating off. And, if you have a hot-water
cylinder, the water heating will not work if the cylinder thermostat detects that the hot water has reached the
correct temperature.

SELECT 207XL

USER INSTRUCTIONS

COP

MO TU WE TH FR SA SU

ON
AUTO
ALLDA

+1H
R

+1h

ON OFF

SET

+1H

TIMES
RESE

+1hr

ADV

SELECT
HW

SELECT CH
BUTTON

CENTRAL
HEATING

HOT
WATER

INTRODUCTION
This central heating programmer can automatically switch your central heating and hot
water ON and OFF, independently, up to 3 times a day, at whatever times you choose.

During installation, the installer selects 24 hour, or 5 day/2 day, or 7 day programming and
2 or 3 on/off periods per day, via a 4 position DIP switch on the back of the unit (see
installation instructions).
IMPORTANT: These settings should only be changed by a qualified person. Contact your
installer.
The 24 hour programmer option runs the same programme every day.
The 5 day/2 day programmer options allows different ON/OFF times at weekends.
The 7 day programmer option allows different ON/OFF times for each day of the week.
The unit is designed to eliminate the possibility of accidental changes to your programme.
Buttons normally visible, only affect your set programme temporarily. All buttons which can
permanently change your programme are located behind the flip-down fascia.
SELECTING OPERATING MODE
The Heating and Hot water mode select buttons are used to set the operating mode for CENTRAL HEATING
and HOT WATER respectively. Each has 4 modes as described:ADV

ON
AUTO
ALLDAY
OFF

Heating mode
Selection button
And indicator

+1hr

MO TU WE TH FR SA SU

ADV

12 : 00
RUN

ON
AUTO
ALLDAY
OFF
ON OFF

Hot Water mode
Selection button
And indicator

+1hr

Central heating and/or Hot water on continuously (I.E. All the time).

AUTO

Central heating and/or Hot water will be switched On or Off as programmed

ALLDAY

Central heating and/or Hot water will be switched On only once each day.
It will switch ON at the first ON time and OFF at the last OFF time.

OFF

Central heating and/or Hot water continuously OFF.

Press the SET button once.
The display will flash above the clock.
Press the +/- buttons to adjust the time.
Hold down button to change time quicker.
Press DAY button to move indicator to
Current day.
Press SET button repeatedly to move
Indicator to RUN position.
NOTE: The unit will automatically return
To run mode if a period of 5 minutes passes
Without any buttons being pressed.

ADV

ON
AUTO
ALLDAY
OFF

+1hr

MO TU WE TH FR SA SU

12 : 00
RUN

ADV

ON
AUTO
ALLDAY
OFF
ON OFF

+1hr

BST/GMT TIME CHANGES
To move the time forward or back 1 hour, press and hold for 3 secs, the TIME +/- button (as appropriate),
while the unit is in run mode.

CHANGING PROGRAMME TIMES

The two built in programmes, one for Central Heating and one for Hot water, can easily be changed to better
suit your needs.
ADV

To change the Central heating programme
Press SET button repeatedly until the display
Indicator is flashing above the radiator symbol.
An indicator will appear above ON and the
Number1 will show above it. This indicates
the time shown on the display is the first ON time.
Change this to the required time by pressing the
+/- buttons.
Press NEXT button to move indicator to above
OFF. Time now shown is the 1st OFF time.
Change as before.
Use the NEXT and +/- buttons in this way to
Program the second time period.
If the unit is set for three ON /OFF periods, the
Number 3 will appear. This is set in exactly the
same way as the previous second time period.

ON
AUTO
ALLDAY
OFF

+1hr
ADV

ON
AUTO
ALLDAY
OFF

+1hr

MO TU WE TH FR SA SU

12 : 00
RUN

RUN

ON
AUTO
ALLDAY
OFF

ON OFF

MO TU WE TH FR SA SU

12 : 00

ADV

+1hr
ADV

ON
AUTO
ALLDAY
OFF

ON OFF

+1hr

If unit is installed as a 7 day programmer, the initial programme displayed will be for Monday. You can go to
any day of the week by pressing DAY button repeatedly. The ON/OFF times can be changed for each day
as above. If you press COPY button, the current programme will be copied into the next day.
If unit is installed as a 5day/2day programmer, the initial programme displayed will be for Monday to Friday.
Pressing DAY button will take you to the programme for Saturday and Sunday. The ON/OFF times can be
changed for each day group as above. If you press COPY button, the current programme will be copied into
the next day group.
If the unit is installed as a 24hr. Programmer, the built in programme will be the same for each day (as for
Monday to Friday). The COPY function is not required if installed as a 24 hr. programmer.
To return to RUN mode, press SET button until the display indicator returns to above the RUN position.
To change HOT WATER programme
Press SET button repeatedly until flashing indicator on display is above the tap symbol and proceed exactly
as Central heating above.
Note
It is not possible to copy Sunday to Monday.
For convenience to allow for programmes to go past midnight, the programme day is from 03:00am to
02:50am the next day.
If your programme gets scrambled, or you want to start again, press the reset button using a non-metallic
tool to re-load the default programmes, then press any button to clear the DIP switch configuration code. The
unit should revert to time setting mode ready for programming.
USING ADVANCE
This function is only available when programme is in AUTO or ALLDAY operating modes.
To Advance Central Heating
ADV

Press the left hand ADV button. This will turn
Central heating ON if it was in an OFF period
And vice versa. It will stay in this state until
either ADV is pressed again, or until a
programmed ON/OFF commences.
An indicator will appear on display top left hand
Corner, pointing at ADV. This is normally covered
By the flip down front fascia panel.

ON
AUTO
ALLDAY
OFF

+1hr

MO TU WE TH FR SA SU

12 : 00
RUN

ADV

ON
AUTO
ALLDAY
OFF
ON OFF

+1hr

To Advance Hot Water
Press the right hand ADV button. This will turn
Hot Water ON if it was in an OFF period
And vice versa. It will stay in this state until
either ADV is pressed again, or until a
programmed ON/OFF commences.
An indicator will appear on display top left hand
Corner, pointing at ADV. This is normally covered
By the flip down front fascia panel.

ADV

ON
AUTO
ALLDAY
OFF

+1hr

MO TU WE TH FR SA SU

12 : 00
RUN

ADV

ON
AUTO
ALLDAY
OFF
ON OFF

+1hr

USING+1HR.
For +1hr Central Heating
Press the left hand +1hr button. If the central Heating operating mode is OFF then it will switch on for 1 hr.
If the central heating operating mode is AUTO or ALLDAY, then during an OFF period, it will switch on for
1hr. If during a ON period, then it will temporarily
MO TU WE TH FR SA SU
ADV
ADV
extend that programme by 1hr.
An indicator will appear on display lower left
corner pointing at +1hr. This is normally covered
by the flip down front fascia panel.
Pressing +1hr again cancels this function.
When in the ON mode the +1hr button has no effect.

ON
AUTO
ALLDAY
OFF

+1hr

12 : 00
RUN

ON
AUTO
ALLDAY
OFF
ON OFF

+1hr

USING+1HR.
For +1hr Hot Water
Press the right hand +1hr button. If the hot water operating mode is OFF then it will switch on for 1 hr.
If the hot water operating mode is AUTO or ALLDAY, then during an OFF period, it will switch on for 1hr. If
during a ON period, then it will temporarily
MO TU WE TH FR SA SU
ADV
ADV
extend that programme by 1hr.
An indicator will appear on display lower right
corner pointing at +1hr. This is normally covered
by the flip down front fascia panel.
Pressing +1hr again cancels this function.
When in the ON mode the +1hr button has no effect.

ON
AUTO
ALLDAY
OFF

+1hr

12 : 00
RUN

ON
AUTO
ALLDAY
OFF
ON OFF

+1hr

POWER INTERRUPTION
In the event of mains supply failure, the back up battery ensures programmer continues to keep time and
retain your stored programme. The screen will go BLANK, but will return when power is restored. If left
continuously without power for more than 30 days, it will stop keeping time. When power is restored, it will be
necessary to reset time and day.
BATTERY REPLACEMENT
Replace with a 3v Lithium button cell type Cr2032. Fit into the back of the unit, observing correct polarity as
marked.
RESET BUTTON
Press the reset button with a non-metallic pointed tool to restore the built in programme.
The display will then show the current state of the configuration switches.

LINKING CENTRAL HEATING AND HOT WATER
If required, it is possible to set both central heating and hot water to follow the same program.
This is done by holding the COPY button down, while pressing reset.
This simplifies programming as changes need only be made once, and will affect both central heating and
hot water.

Configuration

Display

2 on/2off/pumped

2 PU

3 on/3off/pumped

3 PU

2 on/2off/gravity

2 GA

3 on/3off/gravity

3 GA
Mon to Sun day indicators

7 day

Mon to Sun successively on

5/2 day

Mon to Fri on alternating with Sat, Sun on

24Hr

Mon to Sun all on together

E.G. 24hr. 2 on/2off pumped, would look like this:ADV

ON
AUTO
ALLDAY
OFF

+1hr

MO TU WE TH FR SA SU

2 PU
RUN

ADV

ON
AUTO
ALLDAY
OFF
ON OFF

+1hr

NOTE
The last letter of the display (i.e. the U or the A) will be L, if central heating and hot water have been linked.
E.G. 2 PL = 2on/2off pumped, linked CH/HW
Press any button to revert to time setting mode. The unit is then ready for programming. See SETTING TIME
OF DAY section.
Factory programme settings
Mon-Fri Sat&Sun
BUILT IN PROGRAMME
1st ON
6:00am
7:00am
st
1
OFF
8:30am
9:00am
For convenience, the programmer has a built in
programme which for many people is perfectly
12:00 noon 12:00 noon
2nd ON
satisfactory, but it can be changed quite easily
nd
2
OFF
12:00 noon 12:00 noon
(see section CHANGING PROGRAMMING
TIMES)
4:30pm
11:00pm
3rd ON
rd
OFF
10:30pm
11:00pm
3
If the unit is installed as a 24 hour programmer,
the built in programme will be the same for each
day (as Mon. to Fri. above).

Installation Instructions
SELECT207XL
Programmer
Select 207xl Technical Data
Power supply
Ambient temperature
Total Input
Switch Rating
Battery type
Battery back up
Wiring
Maintenance
Disconnection class

230v AC 50Hz.
Operating 0°C to 35°C
6A
230vAC 6(2)A
3v Lithium button Cr2032
30 days(Time & programme)
For fixed wiring only
No user maintenance reqd.
1B

This unit must be installed by a competent person in accordance with the latest appropriate wiring
regulations.
All 3 port spring return motorised valves can
remain powered ON in the CH position after the
Pre Installation set-up
demand for heating has been satisfied, even if the
boiler and the pump are switched off. It can be left
Before installing, set the bank of 4 DIP switches
on all night, using twice as much energy as it
on the back, to configure the unit according to the
should. The valve will only return from this
chart below.
‘latched’ position to the HW position after a
demand for HW or HW & CH together. This can
gravity
Pumped
lead to motor burn out, and failure of any make of
3 port spring return motorised valve.
7 day
The Select 207 programmer is supplied with a
24Hr
patented system to prevent this ‘latching’.
5/2 day
Whenever the programme stops calling for CH, it
2 on/offs
3 on/offs
sends a signal to the valve to fully switch it off.
This will significantly prolong the life of all makes
of 3 port spring return motorised valves and save
DIP switches shown in factory default position
energy. The Select 207 is supplied with ‘DEPumped – Allows independent control of CH and
LATCH’ activated. (It has no effect on 2 port
valves).
HW.
Gravity – Does not allow CH without HW, but can
To de-activate the ‘DE-LATCH’, cut the link as
indicated on the back of the programmer before
Provide HW without CH.
24Hr. Runs same programme every day
installing.
5/2 Day - Allows different ON/OFF times at
INSTALLATION
weekend
7 Day - Allows different on/off times every day
This unit is compatible with many other
programmers and may be fitted to existing
standard wall plates. Please consult the ‘WIRING
Locate the back up battery, remove packing and
INTERCHANGE GUIDE’ for compatible
fit to the back of the unit, observing correct
programmer types. Some are directly
polarity as marked.
interchangeable, others will require minor
This will ensure times and programme settings
changes to wiring connections.
are maintained during temporary power
Be sure to switch off the mains supply before
interruptions.
starting. Please read all installation instructions
before proceeding.
When unit is first switched on, or when the reset
Ensure that the fixed wiring connections to the
button is pressed, the status of the DIP switches
mains supply, is via a fuse rated at not more
is displayed.
6 amps, and a class ‘A’ switch, having a contact
Energy saving feature
separation of a minimum of 3mm in all poles.
Sunvics patented ‘De-Latch’ saves energy and
increases the life of 3 port spring return motorised
valves.

DIRECT UPGRADE FOR EXISTING PROGRAMMERS

1.Switch off mains. Loosen 2 securing screws on
old programmer and unplug it.
2.Check existing wall-plate has been correctly
fitted. (See section,Fitting wall plate)
3.Plug SELECT programmer into wall-plate and
re-tighten screws. Switch on at mains.
4.Press RESET button located behind the flipdown fascia panel. The status of the DIP switch
settings will be displayed. Pressing any button will
cause the display to go to time setting mode.
5.Set timing and programme as detailed in user
guide
FITTING WALL PLATE
1.Position the wall-plate (terminals along the top
edge) with 60mm(Min) clearance to its right,
25mm(Min) above, 90mm(Min) below. Ensure that
the supporting surface will fully cover the back of
the programmer.
2.Ideal location would be 1.4m above floor level,
easily accessible, reasonably lit and free from
condensation or temperature extremes.
3.Fix the wall-plate to a flush mounting single
conduit box type UA1(BS4662) using M3.5 x 14
bolts.
4.Ensure that the wiring to the wall-plate terminals
leads directly away from the terminals and is
completely enclosed within the wall-plate
aperture. Wire ends must be stripped and
screwed to the terminals, so that minimal bare
wire is showing.
5.If the unit is fitted to a metal surface, IT IS
ESSENTIAL that the metal be earthed. Do not use
a surface mounting box.
6.Ensure the mains supply is switched off, then
make wiring connections. No EARTH connection
is required, but ensure continuity of EARTH
throughout the system.
7.After wiring, plug unit into wall plate and tighten
the securing screws. Switch on at mains.
8.Press RESET button located behind the flipdown fascia panel. The status of the DIP switch
settings will be displayed. Pressing any button will
cause the display to go to time setting mode.
9.Setting timing and programme as detailed in
user guide.
10.NEVER fit or remove the unit to a LIVE
wall-plate.

This product complies with the essential requirements of
the following EC Directives:
Electro-magnetic compatibility directive
EMC 89/336/EEC (as amended by 91/263/EEC
And 92/31/EEC
Low Voltage directive
LVD 73/23/EEC;93/68/EEC

Programmer Internal Wiring Diagram

Electronics

Mains Fused
6Amps

1
HW
OFF

CH
OFF

HW
ON

CH
ON

SUNVIC CONTROLS Ltd.
Bellshill Road
Uddingston
Glasgow
G71 6NP
Tel 01698 812944
Fax 01698 813637

Tech Helpline 01698 810945
Tech Help. Fax 01698 307437
WWW.sunvic.co.uk
In the interests of continuous product
improvement, Sunvic Controls reserve the right to
alter designs, specifications and materials, without
prior notice, and cannot accept liability for error.
Installation leaflet LE/497/0001 ISSUE 01 FEB 2003

DIRECT PLUG-IN REPLACEMENT FOR EXISTING PROGRAMMERS

Programmer will plug directly onto existing wall-plates of the following programmers without any rewiring, just follow the installation
instructions.
MANUFACTURER
ACL

DANFOSS RANDALL

MODEL
LP112, LS241, LS522
LS722, LP241, LP522
LP722
FP75, FP15, CP75, CP15

DRAYTON

TEMPUS 3 & 4 & 7

MANUFACTURER
LANDIS &GYR

MODEL
RWB2, RWB2.9, RWB 102
RWB200, RWB252,
RWB20, RWB40
MINIMINDER

POTTERTON
GLOW-WORM

MASTERMIND

SUNVIC

SELECT 207

Otherwise fit new wall-plate supplied, and refer to wiring interchange guide below.
WIRING INTERCHANGE GUIDE
When replacing any of the below with your Sunvic SELECT 207XL programmer, fit new wall-plate supplied and follow the connection
details shown. Whilst every effort is made to ensure accuracy of the instructions given, you will appreciate that discrepancies may occur,
due to various reasons outside of our control.

Make

Model

Sunvic

SELECT 207XL

Terminals
N

SP100 & SP50

SP2

Satchwell

Libra & DHP2201

Satchwell

ET1401 & ET1451

Honeywell

ST699B & C

ST499A

ST6300 & ST6400

ST7100

2000

hw off

ch off

922 & 972

6
2

ACL

Randall

hw on

ch on

4033

701

702

102

3060 & 3020P

1&7

3033

1&7

3&6

MK11 R6

1&2

TSR2P

4&5

3&6

Potterton

EP2000 & EP3000

Horstmann

Amethyst 7 & 10

Coral

Diadem

Diamond

Gem

Leucite

Smiths

Centroller

Switchmaster

400 & 600

805 & 900 & 9000

Thorn

Microtimer

Towerchron

T2002
T2000 & T2003

N
N

L
L

HW
HW ON

CH
CH On

SET2 & SET5
TSR3+3

Sangamo

410F1 & F9 & F414

HW OFF CH OFF

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2007:08:10 11:24:28-03:00
Create Date                     : 2007:08:10 11:24:28-03:00
Format                          : application/pdf
Title                           : Microsoft Word - SeL_207_XL_INST_1_plain.doc
Creator                         : Martin
Document ID                     : uuid:47de685c-c98a-4548-aee5-0611e22a11f3
Instance ID                     : uuid:efd681d2-2bfd-43f0-b146-163dd67180b9
Page Count                      : 8
Author                          : Martin

EXIF Metadata provided by EXIF.tools

SeL_207_XL_INST_1_plain Sunvic Sp2 Programmer Select 207

Navigation menu

Versions of this User Manual:

Views

Navigation