68 0164 T8600D. T8601D, And T8602D Chronotherm IV Deluxe Programmable Thermostats T8601D Manual

User Manual: CHRONOTHERM T8601D

Open the PDF directly: View PDF PDF.
Page Count: 28

PRODUCT DATA
® U.S. Registered Trademark
Copyright © 1997 Honeywell Inc. • • All Rights Reserved
T8600D, T8601D and T8602D
Chronotherm
®
IV Deluxe Programmable
Thermostats
APPLICATION
The T8600, T8601 and T8602 Chronotherm® IV Deluxe
Programmable Thermostats provide electronic control of
24 Vac single-stage heating and cooling systems.
T8600/T8601/T8602
FEATURES AND BENEFITS
•Full seven-day program capability; different schedules
and temperature setpoints may be selected for
everyday to match the homeowner’s flexible schedule.
•Copy key makes programming easier and faster for
the installer and homeowner.
•Daylight Savings Time (DST) key for quick change in
and out of Daylight Savings Time.
•Models available with programmable fan operation for
added homeowner comfort.
•Easy temporary temperature setpoint changes for
current period, vacation hold (1 to 255 days) or
indefinite hold adds to the homeowner comfort and
energy savings.
• Frequently used keys are located by the Liquid Crystal
Display (LCD) for quick and easy access to
information.
•Attractive styling complements any decor to the
homeowner’s delight.
•Back lighting the large display makes the LCD very
easy to read.
Contents
Application............................................................................. 1
T8600/T8601/T8602 Features and Benefits ......................... 1
Specifications ........................................................................ 2
Ordering Information ............................................................. 2
Installation ............................................................................. 4
Wiring .................................................................................... 4
Settings ................................................................................. 6
Installer Setup ....................................................................... 7
Installer Self-Test................................................................. 10
Thermostat Information ....................................................... 11
Programming....................................................................... 11
Operation ............................................................................ 16
Troubleshooting Guide ........................................................ 17
Cross Reference ................................................................. 19
Wiring Diagrams (Fig. 15-20) .............................................. 24
•Models available with outdoor temperature sensor
capability for homeowner convenience. The sensor is
also more accurate than a thermometer.
•Configurable features allows one model to be used to
replace many different models (less inventory, no
longer need to carry separate models to get these
features).
—°F or °C temperature display;
—Automatic or manual changeover;
—Electric or conventional heat fan operation
—Adjustable heating cycle rate.
•Minimum off time for cooling compressors and heat
pumps protects the equipment and extends the
equipment life.
•Easy installation, setup and system test saves
installer time and increases productivity.
•Self-test simplifies troubleshooting and saves time by
overriding the time delays.
•Adaptive Intelligent Recovery™ control brings the
room temperature to temperature setpoint at the
programmed time, maximizing comfort and energy
savings.
• Setpoints are permanently held in memory (no
batteries used) and retained during power outages for
increased installer and homeowner convenience.
•Power stealing, hardwired and battery powered
models available for virtually all equipment and
application needs.
•Universal Versaguard™ Thermostat guards available
for added security.
68-0164-1
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1 2
ORDERING INFORMATION
When purchasing replacement and modernization products from your TRADELINE® wholesaler or distributor, refer to the
TRADELINE® Catalog or price sheets for complete ordering number.
If you have additional questions, need further information, or would like to comment on our products or services, please write or
phone:
1. Your local Home and Building Control Sales Office (check white pages of your phone directory).
2. Home and Building Control Customer Logistics
Honeywell Inc., 1885 Douglas Drive North
Minneapolis, Minnesota 55422-4386
In Canada—Honeywell Limited/Honeywell Limitée, 35 Dynamic Drive, Scarborough, Ontario M1V 4Z9.
International Sales and Service Offices in all principal cities of the world. Manufacturing in Australia, Canada, Finland, France,
Germany, Japan, Mexico, Netherlands, Spain, Taiwan, United Kingdom, U.S.A.
SPECIFICATIONS
IMPORTANT
The specifications given in this publication do not
include normal manufacturing tolerances. Therefore,
this unit might not exactly match the listed
specifications. This product is tested and calibrated
under closely controlled conditions, and some minor
differences in performance can be expected if those
conditions are changed.
Thermostat Models
T8600, T8601 and T8602 Thermostats provide features listed
in Table 1.
Electrical Rating (Nominal Range):
24 Vac, 50/60 Hz.
20 to 30 Vac, 50/60 Hz.
Batteries:
Only T8602 models require batteries.
Loss of Power:
The thermostat will maintain programmed times and
temperatures for the life of the product. The clock and day
information is retained for a minimum of thirty minutes.
System Current Load Ratings:
6 VA maximum at 30 Vac, 50/60 Hz.
Output Relay Load Rating:
See Table 2.
Temperature:
Ratings:
Operating Ambient: 40°F to 110°F (4°C to 43°C).
Shipping: -30°F to +150°F (-34°C to +65°C).
Display Accuracy: ±1°F (±0.5°C).
Setpoint:
Range:
Heating: 40°F to 90°F (4.5°C to 32°C).
Cooling: 45° F to 99°F (7°C to 35°C)
Differential: 3°F (1.5°C).
Default Settings: see Table 3.
Minimum Stage Operation Time:
Minimum Off (Heat and Cool ): factory setting 5 minutes;
option 0 to 5 minutes.
Humidity Ratings:
5% to 90% RH, noncondensing.
Clock Accuracy:
+1 minute per month.
System Changeover System
Selection Fan
Selection Comments
T8600 (powered by either the heating or cooling system)
D Heat-Cool Automatic Heat-Off-Cool-Auto On-Auto System and fan selections are done by keyboard.
T8601 (powered by common wire to supply power)
D Heat-Cool Automatic Heat-Off-Cool-Auto On-Auto System and fan selections are done by keyboard.
T8602 (powered by batteries)
D Heat-Cool Automatic Heat-Off-Cool-Auto On-Auto System and fan selections are done by keyboard.
Table 1. Thermostat Features.
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1
3
Table 2. Maximum Amps at 30 Vac.
Table 3. Default Setpoints.
Period Time Heat
Setpoint Cool
Setpoint Fan
Setting
Wake 6:00 AM 70°F
(21°C) 78°F
(25.5°C) Auto
Leave 8:00 AM 62°F
(16.5°C) 85°F
(29.5°C) Auto
Return 6:00 PM 70°F
(21°C) 78°F
(25.5°C) Auto
Sleep 10:00 PM 62°F
(16.5°C) 82°F
(28°C) Auto
Finish:
Taupe color.
Dimensions:
See Fig. 1.
Mounting Means:
The thermostat mounts on a wallplate. The wallplate mounts
horizontally on a wall or outlet box with two no. 6 x 32 screws
(included).
Accessories:
C7089B Outdoor Temperature Sensors (69-1020).
Universal Versaguard™ Thermostat guards.
RECYCLING NOTICE
If this control is replacing a control that contains
mercury in a sealed tube, do not place your old
control in the trash.
Contact your local waste management authority for
instructions regarding recycling and the proper
disposal of the old thermostat.
Fig. 1. Dimensions of thermostat in in. (mm).
6-1/16 (154) 1/2
(13)
1-9/16
(40)
3-3/4
(95)
3-1/2
(89)
1-13/16
(46)
3/8 (10)
2-3/4 (70)
3-5/8 (92)
M10359
Relay Running (A) Inrush (A)
Fan 0.5 2.5
Heat 1.5 3.5
Cool 1.5 7.5
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1 4
INSTALLATION
When Installing this Product...
1. Read these instructions carefully. Failure to follow the
instructions can damage the product or cause a
hazardous condition.
2. Check the ratings given in the instructions and on the
product to make sure the product is suitable for your
application.
3. Installer must be a trained, experienced service
technician.
4. After completing installation, use these instructions to
check out the product operation.
Location
Install the thermostat about 5 ft (1.5m) above the floor in an
area with good air circulation at average temperature. See
Fig. 2.
Do not install the thermostat where it can be affected by:
—drafts, or dead spots behind doors and in corners.
—hot or cold air from ducts.
—radiant heat from sun or appliances.
—concealed pipes and chimneys.
—unheated (uncooled) areas such as an outside wall
behind the thermostat.
Wallplate Installation
The thermostat can be mounted horizontally on the wall or on
a 2 in. x 4 in. wiring box. Position wallplate horizontally on the
wall or on a 2 in. x 4 in. wiring box.
5 FEET
[1.5 METERS]
YES
NO
NO
NO
M10106
1. Position and level the wallplate (for appearance only).
The thermostat will function properly even when not
level.
2. Use a pencil to mark the mounting holes. See Fig. 3.
3. Remove the wallplate from the wall and drill two 3/16
inch holes in the wall (if drywall) as marked. For firmer
material such as plaster, drill two 7/32 inch holes.
Gently tap anchors (provided) into the drilled holes until
flush with the wall.
4. Position the wallplate over the holes, pulling wires
through the wiring opening.
5. Loosely insert the mounting screws into the holes.
6. Tighten mounting screws.
WIRING
All wiring must comply with local electrical codes and
ordinances. Follow equipment manufacturer wiring
instructions when available. Refer to Fig. 15 through 20 for
typical hookups. A letter code is located near each terminal
for identification. Refer to Table 4 for terminal designations.
CAUTION
Disconnect power before wiring to prevent electrical
shock or equipment damage.
1. Loosen the terminal screws on the wallplate and
connect the system wires. See Fig. 4
Fig. 2. Typical location of thermostat.
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1
5
WIRES
THROUGH WALL
WALL
MOUNTING
HOLES
M15044
MOUNTING
SCREWS
WALL
ANCHORS
(2)
Fig. 3. Mounting the wallplate.
IMPORTANT
Use 18 gauge, color-coded thermostat cable for
proper wiring.
2. Securely tighten each terminal screw.
3. Push excess wire back into the hole.
4. Plug the hole with nonflammable insulation to prevent
drafts from affecting the thermostat.
Standard
Terminal
Designations
Alternate
Terminal
Designations Typical Connection Function Terminal Type
B— Heating damper or changeover valve Output 24V powered contact
CB
a
, C, X1, X2 Common Input
GF Fan relay Output 24V powered contact
OR Cooling damper or changeover valve Output 24V powered contact
OT, OT — Outdoor temperature sensor (C7089B) Input —
RV 24V system or heating transformer Input —
RC — 24V cooling transformer Input —
W H1, R3 Heating relay Output 24V powered contact
Y C1, M Compressor contactor Output 24V powered contact
a
Some OEM models label the terminal for transformer common B.
M4826
FOR WRAPAROUND
INSERTION STRIP
7/16 IN. (11 MM).
FOR STRAIGHT
INSERTION STRIP
5/16 IN. (8 MM).
Fig. 4. Proper wiring technique.
Mounting Thermostat Wallplate
The thermostat mounts on the wallplate after they are
installed.
1. Engage tabs at the top of thermostat and wallplate. See
Fig. 5.
2. Press lower edge of case to latch.
NOTE: To remove the thermostat from the wall, first pull out
at the bottom of the thermostat; then remove the top.
Table 4. Terminal Designations and Descriptions.
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1 6
Fig. 5. Mounting thermostat on wallplate.
SETTINGS
Using Thermostat Keys
The thermostat keys are used to:
•set current day and time,
•program times and setpoints for heating and cooling,
•temporarily override program temperatures,
•display present setting,
•configure Installer Setup,
•check System Test,
•display outdoor temperature (select models),
•set the system operation,
•set the fan operation.
See Fig. 6 for the location of the keys.
System and Fan Settings
The system default setting is Heat and the fan default setting
is Auto. Use the System and Fan keys to change the settings.
See Fig. 7. The fan settings can be set for each program
period individually. The system selection is for all the program
periods.
Fig. 6. Key locations and descriptions.
M15043
B.
PRESS LOWER EDGE OF CASE TO LATCH.
A.
ENGAGE TABS AT TOP OF THERMOSTAT AND WALLPLATE.
M10405A
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day Heat/Cool
Settings
Daylight
Time Copy
INCREASE TEMPERATURE
SETTING OR SCROLL
FORWARD THROUGH
INSTALLER SETUP OPTIONS
DECREASE TEMPERATURE
SETTING OR SCROLL
BACKWARD THROUGH
INSTALLER SETUP OPTIONS
DISPLAY INFORMATION
SUCH AS PRESENT
SETTINGS AND OUTDOOR
TEMPERATURE
RETURN TO
NORMAL
OPERATIONS
ENTER
INDEFINITE
OR TIMED
HOLD MODE
SET CURRENT
DAY AND TIME
SET CURRENT OR
PROGRAM DAY
CHANGE BETWEEN
DAYLIGHT SAVINGS
AND STANDARD TIME
INCREASE TIME SETTING
OR SCROLL FORWARD
THROUGH INSTALLER SETUP
AND SYSTEM TEST
DECREASE TIME SETTING
OR SCROLL BACKWARD
THROUGH INSTALLER
SETUP AND SYSTEM TEST
COPY ONE PROGRAMMED
DAY TO ANOTHER DAY
SET WAKE TIMES
AND SETPOINTS
CHANGE BETWEEN
HEATING AND COOLING
SETPOINTS
SET LEAVE TIMES
AND SETPOINTS
SET RETURN TIMES
AND SETPOINTS
SET SLEEP
TIMES AND
SETPOINTS
SELECT SYSTEM
OPERATION
SELECT FAN
OPERATION
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1
7
M15042
Hold Temp
Run
Program
Copy
Daylight
Time
Set Current
Day/Time
System Fan
Time Set Program
Day System
Fan
Wake Leave Return Sleep
Heat/Cool
Settings
System settings control the thermostat operation as follows:
Heat: The thermostat controls the heating.
Off: Both the heating and cooling are off.
Cool: The thermostat controls the cooling.
Auto: The thermostat automatically changes between
heating and cooling operation, depending on the indoor
temperature.
Fan settings control the system fan as follows:
On: Fan operates continuously.
Auto: Fan operates with equipment.
Fig. 7. Thermostat System and Fan key locations.
NOTE: Always press the keys with your fingertip or similar
blunt tool. Sharp instruments like a pen or pencil
point can damage the keyboard.
Temperature Settings
Refer to Table 5 for the default program. If the daytime energy
savings period is not used, press the period key (Leave or
Return) until the time is blank. The fan setting feature is
available on select thermostat models. See Programming
Section for complete instructions on changing the program.
Table 5. Default Program Settings.
Period Time Heat
Setpoint Cool
Setpoint Fan
Setting
Wake 6:00 AM 70°F
(21°C) 78°F
(25.5°C) Auto
Leave 8:00 AM 62°F
(16.5°C) 85°F
(29.5°C) Auto
Return 6:00 PM 70°F
(21°C) 78°F
(25.5°C) Auto
Sleep 10:00 PM 62°F
(16.5°C) 82°F
(28°C) Auto
The Installer Setup is used to customize the thermostat to
specific systems. Some of the options include temperature
display, changeover and outdoor temperature display. Installer
Setup numbers are listed in Table 6. The table includes all the
configuration options and the factory-settings for the
thermostat.
A combination of key presses are required to use the Installer
Setup feature.
—To enter the Installer Setup, press and hold the
Information i key with the increase ▲ and decrease ▼
keys until the first number is displayed. All display
segments appear for approximately three seconds before
the number is displayed. See Fig. 8 and 9.
—To advance to the next Installer Setup, press the Time ▲▲
key.
—To change a setting, use the increase ▲ or decrease ▼
key.
—To scroll the Installer Setup numbers backwards, press
the Time ▼▼ key.
—To exit the Installer Setup, press Run Program.
Aux Ht
Heat
Auto
System Fan
Off Auto
Wake
Mon
Wait
In
Room
Outdoor
%Humid
Auto
Sav
AM
PM
Hold for
Cool Repl Batt
On
Recovery
DST
Cool
TueWedThuFriSatSun
LeaveReturnSleep
M10345
Set Program
Set Day/Time
Start Time Temporary Setting Enrg
Em Heat
Em Ht
M10404
INSTALLER SETUP
NUMBER DISPLAY
(COLUMN 2
OF TABLE 6)
FACTORY SETTING
OR OTHER CHOICE
DISPLAY (COLUMN 3
OR 5 OF TABLE 6)
Fig. 8. Display of all the segments of the LCD.
Fig. 9. Display of Installer Setup number and setting.
CAUTION
Heat pump and electric heat systems must be
configured to 1 in Installer Setup number 2 to prevent
equipment damage caused by the system running
without the fan.
IMPORTANT
Only configurable numbers are shown on the device.
Example: If thermostat does not have a system key,
Installer Setup Number 12 will not be displayed.
Review Table 6 factory-settings and mark any
desired changes in the Actual Settings column.
When Installer Setup is complete, review the settings
to confirm that they match the system.
INSTALLER SETUP
NOTE: For most applications, the thermostat factory-
settings will not need to be changed. Review the
factory settings in Table 6 and if no changes are
necessary, go to the Installer System Test section.
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1 8
Table 6. Thermostat Installer Setup Options.
(continued)
Installer Setup
Number (Press
Time ▲ key to Factory-Setting Other Choices
(Press ▲ or ▼ key to change) Actual
Select change) Display Description Display Description Setting
Not used 1 — — — — —
Fan operationa20Conventional
applications where
equipment controls fan
operation in heat mode
1 Heat pump or electric heat
applications where thermostat
controls fan operation in heat
mode
Not used 3 — — — — —
Heating cycle
rate 466—6 cph used for
conventional heat 1, 3 or 9 1—1 cph used for radiant floor
heat, gravity system
3—3 cph used for hot water
systems or high efficiency
furnaces
9—9 cph used for electric heat
systems
Not used 5 thru 11 — — — — —
System setting
adjustment 12 1 Manual changeover 0 or 2 0—Auto changeover
2—Fixed auto changeover
Adaptive
Intelligent
Recovery™
control
13 0 Adaptive Intelligent
Recovery™ control is
activated (system
starts early so setpoint
is reached by start of
program period)
1 Conventional recovery (system
starts recovery at programmed
time)
—
Degree
temperature
display
14 0 Temperature is
displayed in °F 1 Temperature is displayed in °C
Not used 15 — — — — —
Clock format 16 0 12-hour clock format 1 24-hour clock format
Not used 17 and 18 — — — — —
Extended fan
operation in
heatinga
19 0 No extended fan
operation after the call
for heat ends
1 Fan operation is extended 90
seconds after the call for heat
ends.
Extended fan
operation in
cooling
20 0 No extended fan
operation after the call
for cool ends
1 Fan operation is extended 90
seconds after the call for cool
ends.
Not used 21 thru 23 — — — — —
Outdoor
temperature
display (select
models)
24 0 No outdoor
temperature is
displayed
1 Outdoor temperature is
displayed. Needs a
C7089B1000 Outdoor Sensor
to operate
Not used 25 thru 29 — — — — —
Deadband 30 3 Heating and cooling
setpoints can be set
no closer than 3°F
(1.5°C)
4 thru 10 Heating and cooling setpoints
can be set no closer than the
chosen value:
4—4°F (2°C)
5—5°F (2.5°C)
6—6°F (3°C)
7—7°F (3.5°C)
8—8°F (4°C)
9—9°F (4.5°C)
10—10°F (5°C)
aNumber 2 must be set to 1 to extend fan operation.
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1
9
Table 6. Thermostat Installer Setup Options (continued).
M10312
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time
Set Current
Day/Time
Wake Leave Return Sleep
Day Heat/Cool
Settings
Daylight
Time Copy
Mon
PM
Set Day/Time
M10313
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day
Day
Heat/Cool
Settings
Daylight
Time Copy
PM
Tue
Set Day/Time
IMPORTANT
Review the settings to confirm that they match the
system. Press Run Program to exit the Installer
Setup. The thermostat has saved the Installer Setup
changes and initiated a reset in order to operate with
these new settings. Be sure to set the current day
and time immediately.
Setting Current Day and Time
1. Press Set Current Day/Time.
NOTE: On initial power up or after an extended power
loss, 1:00 pm flashes on the display until a key
is pressed.
2. Press Day until the current day is displayed.
NOTE: Sun=Sunday, Mon=Monday, Tue=Tuesday,
Wed=Wednesday, Thu=Thursday, Fri=Friday,
Sat=Saturday.
M10314
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day
Time
Heat/Cool
Settings
Daylight
Time Copy
AM
Tue
Set Day/Time
3. Press Time ▲▲ or Time ▼▼ until the current time is
displayed.
NOTE: Tapping the Set Current Day/Time will change
the time in one hour increments.
Installer Setup
Number (Press
Time ▲ key to Factory-Setting Other Choices
(Press ▲ or ▼ key to change) Actual
Select change) Display Description Display Description Setting
Not used 31 and 32 — — — — —
Minimum off time
for the
compressor
33 5 5 minute minimum off
time for the
compressor
0 thru 4 Minimum number of minutes (0
thru 5) the compressor will be
off between calls for the
compressor
Temperature
range stops in
heating
34 90 Highest setpoint
heating can be set to 40 to 89 Temperature range (1°F
increments) heating setpoint
can be set to
Temperature
range stops in
cooling
35 45 Lowest setpoint
cooling can be set to 46 to 99 Temperature range (1°F
increments) cooling setpoint
can be set to
Not used 36 — — — — —
Temperature
display
adjustment
37 0 No difference in
displayed temperature
and actual room
temperature
3 thru -3 1—Display adjusts to 1°F
higher than actual room
temperature
2—Display adjusts to 2°F
higher than actual room
temperature
3—Display adjusts to 3°F
higher than actual room
temperature
-1—Display adjusts to 1°F lower
than actual room temperature
-2—Display adjusts to 2°F lower
than actual room temperature
-3—Display adjusts to 3°F lower
than actual room temperature
aNumber 2 must be set to 1 to extend fan operation.
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1 10
M10315
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day Heat/Cool
Settings
Daylight
Time
Daylight
Time
Copy
AM
DST
Tue
Set Day/Time
NOTE: If the current time is Daylight Savings Time,
press Daylight Time until DST is displayed.
M10316
Time Set Program
System Fan
Run
Program
Run
Program Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day Heat/Cool
Settings
Daylight
Time Copy
Auto
System Fan
Wake
Room
AM
DST
Tue
Heat
Aux Ht
Heat
Auto
System Fan
Off Auto
Wake
Mon
Wait
In
Room
Outdoor
%Humid
Auto
Sav
AM
PM
Hold for
Cool Repl Batt
On
Recovery
DST
Cool
TueWedThuFriSatSun
LeaveReturnSleep
M10345
Set Program
Set Day/Time
Start Time Temporary Setting Enrg
Em Heat
Em Ht
INSTALLER SYSTEM TEST
Use the Installer System Test to check the thermostat operation.
Refer to Table 7 for a list of the available system tests.
To start the system test:
CAUTION
The minimum off time for compressors is bypassed
during the Installer System Test. Equipment damage
can occur if the compressor is cycled too quickly.
Press and hold the increase ▲ and ▼ decrease keys, at the
same time, until 10 appears. All segments of the display are
displayed for three seconds before 10 appears. See Fig. 10
and 11.
M10257A
TEST NUMBER
Fig. 10. Display of all the segments of the LCD.
Refer to Table 8 for the directions and results of the specific
tests.
NOTE: Press Time ▲▲ to advance to the next test and Time
▼▼ to go to the previous test. Press Run Program to
exit the system test.
Table 8. Installer System Test Options.
Fig. 11. Display of test number.
4. Press Run Program.
Table 7. Tests Available in Installer System Test.
Key to Press Test
Number Description
Heating Equipment System Test
Time ▲10 Enter heating equipment system test.
▲11 Heat comes on. When Installer Setup number 2 is 1, the system fan is also energized.
▼10 Heat and system fan turn off.
Cooling Equipment System Test
Time ▲30 Change from heating to cooling equipment system test.
▲31 Cool and system fan come on.
▼30 Cool and system fan turn off.
Fan Equipment System Test
Time ▲40 Change from cooling to fan equipment system test.
▲41 Fan comes on.
▼40 Fan turns off.
Key Operation System Test
Time ▲60 2 Change from fan to key operation system test.
Test
Number System Test Description
10-19 Heating equipment can be turned on and off
30-39 Cooling equipment can be turned on and off
40-49 Fan equipment can be turned on and off
60 0 to
60 19 Keyboard keys test
70-79 Thermostat information including date code and
software versions are displayed
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1
11
NOTE: Press any key and the numbers will change on the
display. Press Time ▼▼ to scroll backwards and Time
▲▲ to scroll forward. The Run Program, Key will not
exit from this test. To exit, go to a different test and
press Run Program.
THERMOSTAT INFORMATION
1. Press the Time ▲ ▲ key to access the thermostat
information.
M4934
2. Press the increase ▲ key to display the production date
code. The first two large digits are the month and the
third digit is the last digit of the year (Example:
027=February 1997).
M10351
3. Press the increase ▲ key again to display the software
identification code. (Example: 02 = software ID code 2)
M4932A
4. Press the increase ▲ key again to display the software
revision number (Example: 001=Revision number 1).
M10229
5. Press the increase ▲ key again to display the EEPROM
identification code. (Example: 314 = EEPROM ID 314)
6. Press the Run Program key to exit the system test. The
M4933A
system test times out after five minutes without any key
presses.
PROGRAMMING
The keyboard is located behind the thermostat cover with
three frequently used keys by the display. The thermostat
display shows day, time, program period, temperature, system
and fan operation selection.
The thermostat can be set for four times and up to eight
temperatures for each day of the week (28 independent time
and 56 temperature settings). The ▲▲ and ▼▼ keys provide
quick temporary temperature changes to increase comfort.
The Hold Temp key provides energy efficient operation for
extended periods of time.
Before starting the programming procedure, use Table 9 to
organize the program schedule. The factory preprogrammed
time, temperature and fan settings are shown in brackets. If a
daytime energy savings period is not used, press the period
key (Leave or Return) until the time is blank. The fan setting
feature is available on select thermostat models.
Setting the Current Day and Time
IMPORTANT
Always press the keys with your fingertip or similar
blunt tool. Sharp instruments like pens and pencil
points can damage the keyboard.
1. Press Set Current Day/Time.
NOTE: On initial power up or after an extended power
loss, 1:00 pm flashes on the display until a key
is pressed.
M10312
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time
Set Current
Day/Time
Wake Leave Return Sleep
Day Heat/Cool
Settings
Daylight
Time Copy
Mon
PM
Set Day/Time
2. Press Day until the current day is displayed.
NOTE: Sun = Sunday, Mon = Monday, Tue = Tuesday,
Wed = Wednesday, Thu = Thursday, Fri =
Friday, Sat = Saturday.
M10313
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day
Day
Heat/Cool
Settings
Daylight
Time Copy
PM
Tue
Set Day/Time
3. Press Time ▲▲ or Time ▼▼ until the current time is
displayed.
NOTE: Tapping the Set Current Day/Time will change
the time in one hour increments.
M10314
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day
Time
Heat/Cool
Settings
Daylight
Time Copy
AM
Tue
Set Day/Time
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1 12
4. Press Run Program.
M10316
Time Set Program
System Fan
Run
Program
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day Heat/Cool
Settings
Daylight
Time Copy
Auto
System Fan
Wake
Room
AM
DST
Tue
Heat
Table 9. Default Time, Setpoints and Fan Settings.
Programming the First Day
Start by programming the Wake time and temperature (and
fan operation on select models) for any one day:
1. Press Wake.
M10317
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake
Wake
Leave Return Sleep
Day Heat/Cool
Settings
Daylight
Time Copy
Heat
Auto
System Fan
Wake
AM
Tue
Set Program
Start Time Setting
Heat
NOTE: If the current time is Daylight Savings Time,
press Daylight Time until DST is displayed.
M10315
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day Heat/Cool
Settings
Daylight
Time
Daylight
Time
Copy
AM
DST
Tue
Set Day/Time
(continued)
Period Start Time Heat Setpoint Cool Setpoint Fan Setting
Monday
Wake [6:00 AM] [70°F (21°C)] [78°F (25.5°C)] [Auto]
Leave [8:00 AM] [62°F (16.5°C)] [85°F (29.5°C)] [Auto]
Return [6:00 PM] [70°F (21°C)] [78°F (25.5°C)] [Auto]
Sleep [10:00 PM] [62°F (16.5°C)] [82°F (28°C)] [Auto]
Tuesday
Wake [6:00 AM] [70°F (21°C)] [78°F (25.5°C)] [Auto]
Leave [8:00 AM] [62°F (16.5°C)] [85°F (29.5°C)] [Auto]
Return [6:00 PM] [70°F (21°C)] [78°F (25.5°C)] [Auto]
Sleep [10:00 PM] [62°F (16.5°C)] [82°F (28°C)] [Auto]
Wednesday
Wake [6:00 AM] [70°F (21°C)] [78°F (25.5°C)] [Auto]
Leave [8:00 AM] [62°F (16.5°C)] [85°F (29.5°C)] [Auto]
Return [6:00 PM] [70°F (21°C)] [78°F (25.5°C)] [Auto]
Sleep [10:00 PM] [62°F (16.5°C)] [82°F (28°C)] [Auto]
Thursday
Wake [6:00 AM] [70°F (21°C)] [78°F (25.5°C)] [Auto]
Leave [8:00 AM] [62°F (16.5°C)] [85°F (29.5°C)] [Auto]
Return [6:00 PM] [70°F (21°C)] [78°F (25.5°C)] [Auto]
Sleep [10:00 PM] [62°F (16.5°C)] [82°F (28°C)] [Auto]
Friday
Wake [6:00 AM] [70°F (21°C)] [78°F (25.5°C)] [Auto]
Leave [8:00 AM] [62°F (16.5°C)] [85°F (29.5°C)] [Auto]
Return [6:00 PM] [70°F (21°C)] [78°F (25.5°C)] [Auto]
Sleep [10:00 PM] [62°F (16.5°C)] [82°F (28°C)] [Auto]
Saturday
Wake [6:00 AM] [70°F (21°C)] [78°F (25.5°C)] [Auto]
Leave [8:00 AM] [62°F (16.5°C)] [85°F (29.5°C)] [Auto]
Return [6:00 PM] [70°F (21°C)] [78°F (25.5°C)] [Auto]
Sleep [10:00 PM] [62°F (16.5°C)] [82°F (28°C)] [Auto]
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1
13
Period Start Time Heat Setpoint Cool Setpoint Fan Setting
Sunday
Wake [6:00 AM] [70°F (21°C)] [78°F (25.5°C)] [Auto]
Leave [8:00 AM] [62°F (16.5°C)] [85°F (29.5°C)] [Auto]
Return [6:00 PM] [70°F (21°C)] [78°F (25.5°C)] [Auto]
Sleep [10:00 PM] [62°F (16.5°C)] [82°F (28°C)] [Auto]
Table 9. Default Time, Setpoints and Fan Settings (continued).
2. Press Day until the desired day is displayed.
M10318
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day
Day
Heat/Cool
Settings
Daylight
Time Copy
Heat
Auto
System Fan
Wake
Mon
AM
Set Program
Start Time Setting
Heat
3. Press Time ▲ ▲ or Time ▼ ▼ until the desired Wake time is
displayed.
NOTE: The program times are in fifteen minute
intervals. (Example: 8:00, 8:15, 8:30).
M10319
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day Heat/Cool
Settings
Daylight
Time Copy
Heat
Auto
System Fan
Wake
Mon
AM
Set Program
Start Time Setting
Heat
Time
4. Press increase ▲ or decrease ▼ key until the desired
Wake temperature is displayed.
NOTE: The setpoint temperature range is 40 to 90°F
(7 to 31°C) for heating and 45 to 99°F (9 to
37°C) for cooling.
M10320
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day Heat/Cool
Settings
Daylight
Time Copy
Heat
Auto
System Fan
Wake
Mon
AM
Set Program
Start Time Setting
Heat
NOTE: Press Fan to modify fan operation. Auto means
the fan will run only when the heating or
cooling equipment is operating. On means the
fan will run continuously for the entire period.
5. Press Heat/Cool Settings to switch to other system
temperature setpoint.
NOTE: The program times are the same for both
heating and cooling.
M10321
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day Heat/Cool
Settings
Heat/Cool
Settings
Daylight
Time Copy Auto
System Fan
Wake
Mon
AM
Cool
Set Program
Start Time Setting
Heat
6. Press increase ▲ or decrease ▼ key until the desired
temperature setpoint is displayed.
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day Heat/Cool
Settings
Daylight
Time Copy
Auto
System Fan
Wake
Mon
AM
Cool
Set Program
Start Time Setting
Heat
M10322
7. Press Leave, Return or Sleep and repeat steps 3, 4, 5
and 5 for programming the rest of the day. The first day
is now programmed.
M10323
Time Set Program
System Fan
Run
Program
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day Heat/Cool
Settings
Daylight
Time Copy
Auto
System Fan
Wake
Room
AM
DST
Tue
Heat
Copying a Day
NOTE: The thermostat must be in the program mode to use
the copy feature. Go to step 2 if the thermostat is
already in the program mode.
1. Press Wake.
M10324
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake
Wake
Leave Return Sleep
Day Heat/Cool
Settings
Daylight
Time Copy
Heat
Auto
System Fan
Wake
AM
Tue
Set Program
Start Time Setting
Heat
IMPORTANT
Repeat steps
1
through
7
for each day of the week
that has a different program than the first day. Refer
to Copying a Day section to copy any program day to
another.
8. Press Run Program when all days are programmed.
2. Press Day to select the day to be copied if different
from the day displayed.
M10325
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day
Day
Heat/Cool
Settings
Daylight
Time Copy
Heat
Auto
System Fan
Wake
Mon
AM
Set Program
Start Time Setting
Heat
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1 14
3. Press Copy.
M10326
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day Heat/Cool
Settings
Daylight
Time Copy
Copy
Mon
4. Press Day until the day to be copied to is displayed.
M10327
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day
Day
Heat/Cool
Settings
Daylight
Time Copy
Mon Wed
5. Press Copy.
NOTE: donE will be displayed for two seconds and
then the normal program display will be
shown.
M10328
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day Heat/Cool
Settings
Daylight
Time Copy
Copy
6. Repeat steps 2 through 5 for all the days desired.
7. Press Run Program.
Clearing Program Period
NOTE: The thermostat must be in the program mode to use
the clear feature. Go to step 2 if the thermostat is
already in the program mode.
1. Press Wake, Leave, Return or Sleep.
M10329
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave
Leave
Return Sleep
Day Heat/Cool
Settings
Daylight
Time Copy
Heat
Auto
System Fan
Mon
AM
Leave
Set Program
Start Time Setting
Heat
M10330
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day
Day
Heat/Cool
Settings
Daylight
Time Copy
Heat
Auto
System Fan
AM
Sat
Leave
Set Program
Start Time Setting
Heat
M10331
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day Heat/Cool
Settings
Daylight
Time Copy
Heat
Sat
Leave
Set Program
Start Time Setting
Leave
M10332
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day Heat/Cool
Settings
Daylight
Time Copy
Heat
Wake
Temporary Setting
2. Press Day until the desired day is displayed.
3. Press Leave, Return or Sleep until the start time and
temperature setting are cleared (approximately 3
seconds).
NOTE: Wake cannot be cleared.
4. Repeat steps 2 and 3 for all the periods to be cleared.
5. Press Run Program.
Setting Temporary Temperatures
Changing Temperature Setting Until the Next
Program Period
Press increase ▲ or decrease ▼ key until the desired
temperature setpoint is displayed.
NOTE: If ▼ or ▲ appear under the temperature display, it
means that both the heating and cooling setpoints
are being adjusted. Tapping the key will change both
the heat and cool setpoints by one degree. Press i
after the desired setpoint is reached to check the
setpoints.
NOTE: The temporary temperature setting is displayed for
approximately 3 seconds. The setting is canceled
when the next period starts or when Run Program is
pressed.
Changing Temperature Setting Indefinitely
1. Press Hold Temp.
M10333
Time Set Program
System Fan
Run
Program
Hold Temp
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day Heat/Cool
Settings
Daylight
Time Copy
Heat
Setting
2. Press increase ▲ or decrease ▼ key to change the
setting, if desired.
M10334
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day Heat/Cool
Settings
Daylight
Time Copy
Heat
Setting
3. Press Heat/Cool Settings to change between heat and
cool settings.
M10335
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day Heat/Cool
Settings
Heat/Cool
Settings
Daylight
Time Copy
Cool
Setting
4. Press increase ▲ or decrease ▼ key to adjust
temperature settings.
M10336
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day Heat/Cool
Settings
Daylight
Time Copy
Cool
Setting
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1
15
NOTE: The display changes from the setpoint to the
room temperature after approximately 3
seconds.
5. Press Run Program to cancel the Hold and to return to
the program.
Changing Temperature Setting Until a
Designated Day and Period
1. Press Hold Temp twice.
M10337
Time Set Program
System Fan
Run
Program
Hold Temp
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day Heat/Cool
Settings
Daylight
Time Copy
Heat
Wake
Hold for
Setting
2. Press Time ▲ ▲ or Time ▼ ▼ until the desired number of
days is displayed (1 to 255 days). (Example: 18 = Hold
will override the daily programs for 18 days)
M10338
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day Heat/Cool
Settings
Daylight
Time Copy
Heat
Wake
Hold for
Setting
Time
3. Press Wake, Leave, Return or Sleep to select the
period the program will start. (Example: Return =
thermostat will stop the Hold at the Return period start
time)
M10339
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return
Return
Sleep
Day Heat/Cool
Settings
Daylight
Time Copy
Heat
Hold for
Return
Setting
M10340
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day Heat/Cool
Settings
Daylight
Time Copy
Heat
Hold for
Return
Setting
4. Press increase ▲ or decrease ▼ key to adjust the
temperature setting, if desired. (Example: Heat 54° =
heating equipment will operate when the room
temperature is below 54°F)
NOTE: When the System is set for Auto (select
models), both heat and cool settings are
needed. If the System is set for Heat, only the
Heat setpoint is needed or if Cool is selected,
only the Cool setpoint is needed.
5. Press Heat/Cool Settings to change between heat and
cool settings.
6. Press increase ▲ or decrease ▼ key to adjust the
temperature setting, if desired. (Example: Cool 84° =
cooling equipment will operate when the room
temperature is above 84°F)
NOTE: In this example, the thermostat uses the Hold setting
for eighteen days and returns to the daily programs
at the Return period start time. The temperature
settings are heating 54°F and cooling 84°F. Only the
heating temperature is used because the System is
set for Heat. The thermostat will use both the heating
and cooling temperature settings when the System
is set to Auto (select models).
IMPORTANT
If the Hold needs to be canceled before the
designated time, press Run Program to return to the
program.
Setting System and Fan
The system default setting is Heat and the fan default setting
is Auto. Use the System and Fan keys to change the settings.
See Fig. 12. The fan settings can be set for each program
period individually. The system selection is for all the program
periods.
System settings control the thermostat operation as follows:
Heat: The thermostat controls the heating.
Off: Both the heating and cooling are off.
Cool: The thermostat controls the cooling.
Auto: The thermostat automatically changes between
heating and cooling operation, depending on the indoor
temperature.
Fan settings control the system fan as follows:
On: Fan operates continuously.
Auto: Fan operates with equipment.
M15042
Hold Temp
Run
Program
Copy
Daylight
Time
Set Current
Day/Time
System Fan
Time Set Program
Day System
Fan
Wake Leave Return Sleep
Heat/Cool
Settings
Fig. 12. Thermostat System and Fan key locations.
Setting Temporary Fan Operation
If your thermostat has a Fan key and this feature, press Fan
until the desired fan operation is selected. This fan setting will
be in effect until the next regularly scheduled period starts.
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1 16
M10342
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day Heat/Cool
Settings
Daylight
Time Copy
Outdoor
HEATING COOLING
PERCENT LOAD
TEMPERATURE
THERMOSTAT
HEAT SETPOINT
P+I CONTROL
POINT
PROPORTIONAL COOL
CONTROL POINT
THERMOSTAT
COOL SETPOINT
P+I CONTROL POINT
PROPORTIONAL HEAT
CONTROL POINT
M4414
100 50 0 50 100
Fig 13. Proportional temperature control versus P+I
temperature control.
Operation Sequence
The thermostat energizes specific terminals depending what
the Fan and System are set to. The LCD will display the time,
room temperature, system and fan selection. Symbols will be
displayed when the heating, cooling or fan is energized. See
Table 10 for specific information.
NOTE: Not all the thermostat models have all the terminals
listed in the Energize column.
Table 10. Conventional System Sequence of Operation.
Using Daylight Savings Time Feature
This feature allows you to change in and out of Daylight
Savings Time with a key press. When the Daylight Time Key is
pressed in the fall, the time will go back one hour. In the
spring, the time will go ahead one hour and the display will
show DST. See Setting the Current Day and Time section for
initial setting instructions.
NOTE: Pressing the Daylight Time Key more than once
within a five minute period will scroll you through
various time options (Example: one hour earlier or
later with or without DST). Pressing the Daylight
Time Key six times in a five minute period will return
you to your original settings.
Displaying the Outdoor Temperature
If your thermostat is equipped with an outdoor sensor, you
can check the temperature at the sensor by pressing i
once.
OPERATION
P+I Control
The thermostat microprocessor based control requires that
the user understands temperature control and thermostat
performance. A conventional electromechanical or electronic
thermostat does not control temperature precisely at setpoint.
Typically, there is an offset (droop) in the control point as the
system load changes. This is a phenomenon that most people
in the industry know and accept. Many factors contribute to
offset including switch differential, thermal lag, overshoot,
cycle rates and system load.
The thermostat microprocessor simultaneously gathers,
compares and computes data. Using this data, it controls a
wide variety of functions. The special proprietary algorithm
(program) in the thermostat eliminates the factors causing
offset. This makes temperature control more accurate than
the conventional electromechanical or electronic thermostats.
The temperature control algorithm is called proportional plus
integral (P+I) control.
The thermostat sensor, located on the thermostat or remote,
senses the current space temperature. The proportional error
is calculated by comparing the sensed temperature to the
programmed setpoint. The deviation from the setpoint is the
proportional error.
The thermostat also determines integral error, which is a
deviation based on the length of error time. The sum of the
two errors is the (P+I) error. The cycle rate used to reach and
maintain the setpoint temperature is computed using the P+I.
The addition of the integral error is what differentiates the
thermostat from many other electronic and electromechanical
thermostats. See Fig. 13.
Equipment Protection
As part of the operational sequence, the thermostat
microprocessor also incorporates minimum off time for all
cooling stages. Using the minimum off time assures that rapid
cycling of equipment does not occur, which extends
equipment life. Minimum off times are set in the Installer
Setup.
Selection
Fan System Call Energize Display
Auto Off None None None
On Off None G
Auto Cool None O None
Auto Cool or Auto Cooling O, G and Y
and
Auto Heat None B None
Auto Heat or Auto Heating B and W
a
Auto Auto None O or B
b
None
a
When electric heat fan is selected, G is energized and fan
symbol is displayed.
b
Based on last piece of equipment called (cooling = O or
heating = B) and Installer Setup selection.
M10341
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time Wake Leave Return Sleep
Day Heat/Cool
Settings
Daylight
Time Copy
Daylight
Time
Auto
System Fan
Wake
Room
AM
Tue
Heat
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1
17
Thermostat Operation
Startup
When power to the thermostat is turned on, a startup and
initialization program begins. The startup occurs only on initial
powerup. After total loss of power for an extended period, the
current time and day may need to be set, but the user
program is held. See Table 11 for the default values.
NOTE: Immediately following initialization, the user can
enter new setpoints to be used in place of the default
values.
Table 11. Default Time, Setpoint and Fan Settings.
Period Time Heat
Setpoint Cool
Setpoint Fan
Setting
Wake 6:00 AM 70°F
(21°C) 78°F
(25.5°C) Auto
Leave 8:00 AM 62°F
(16.5°C) 85°F
(29.5°C) Auto
Return 6:00 PM 70°F
(21°C) 78°F
(25.5°C) Auto
Sleep 10:00 PM 62°F
(16.5°C) 82°F
(28°C) Auto
Adaptive Intelligent Recovery
®
Feature
Adaptive Intelligent Recovery® ensures that the comfort
setting is achieved at the programmed time regardless of
weather conditions. Conventional recovery, however, starts
recovery at the beginning of the programmed time period and
uses the equipment to achieve the comfort settings as soon
as possible.
Fig. 14. Temperature change in recovery.
70°F
60°FSLEEP
HEATING MODE
WAKE
SETPOINT
TEMPERATURE
ACTUAL
TEMPERATURE
M6185A
TROUBLESHOOTING GUIDE
Refer to Table 12 for troubleshooting information.
Adaptive Intelligent Recovery® calculates the recovery ramp
based on the number of degrees away from the desired
setpoint, previous equipment performance, and weather
history to initiate recovery at the optimal time to achieve the
comfort setting at the desired time.
Once the recovery ramp is intersected, the setpoint changes
from the setback setpoint to the comfort setpoint. This change
snaps on
the equipment and runs the equipment until the
setpoint is reached. If the setpoint is reached too early or too
late, the ramp is adjusted for the next days' recovery.
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1 18
(continued)
Table 12. Troubleshooting Information.
Symptom Possible Cause Action
Display will not
come on. Thermostat is not being
powered. • Check for 24 Vac between R and C or W terminals.
— If missing 24 Vac:
— check if the circuit breaker is tripped—reset the circuit
breaker.
— check if the system fuse is blown—replace the fuse.
— check if the power switch on the HVAC equipment is in the
Off position—set to the On position.
— check wiring between thermostat and HVAC equipment—
replace any broken wires and tighten any loose connections.
— If 24 Vac is present, proceed with troubleshooting.
Temperature
display is incorrect. Room temperature display has
been reconfigured. Enter Installer Setup number 37 and reconfigure the display.
Thermostat is configured for °F
or °C display. Enter Installer Setup number 14 and reconfigure the display.
Bad thermostat location. Relocate the thermostat.
Temperature
settings will not
change. (Example:
Cannot set the
The upper or lower temperature
limits were reached. Check the temperature setpoints:
• Heating limits are 40 to 90°F (4.5 to 32°C)
• Cooling limits are 45 to 99°F (7 to 35°C) except D model cooling
limits are 48 to 99°F.
heating higher or
the cooling lower.) The setpoint temperature range
stops were configured. Check Installer Setup numbers 34 and 35 and reconfigure the setpoint
stops.
Heating will not
come on. No power to the thermostat. • Setpoint is above room temperature.
• Check for 24 Vac between R and C or W terminals.
— If missing 24 Vac:
— check if the circuit breaker is tripped—reset the circuit
breaker.
— check if the system fuse is blown—replace the fuse.
— check if the power switch on the HVAC equipment is in the
Off position—set to the On position.
— check wiring between thermostat and HVAC equipment—
replace any broken wires and tighten any loose connections.
— If 24 Vac is present, proceed with troubleshooting.
Heating will not
come on. Thermostat minimum off time is
activated. Wait up to five minutes for the system to respond.
System selection is not set to
Heat. Set system selection to Heat.
Heating setpoint is below room
temperature. Check heating setpoint. Set heating setpoint to desired temperature.
Cooling will not
come on. No power to the thermostat. • Setpoint is below room temperature.
• Check for 24 Vac between R or RC and C or Y terminals (D models
requires power to R at all times).
— If missing 24 Vac:
— check if the circuit breaker is tripped—reset the circuit
breaker.
— check if the system fuse is blown—replace the fuse.
— check if the power switch on the HVAC equipment is in the
Off position—set to the On position.
— check wiring between thermostat and HVAC equipment—
replace any broken wires and tighten any loose connections.
— If 24 Vac is present, proceed with troubleshooting.
Thermostat minimum off time is
activated. • Wait up to five minutes for the system to respond.
• Enter Installer Setup number 33. Reconfigure minimum off time (if
required).
System selection is not set to
Cool. Set system selection to Cool.
Cool setpoint is above room
temperature. Check cooling setpoint. Set cooling setpoint to desired temperature.
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1
19
Table 12. Troubleshooting Information (continued).
Symptom Possible Cause Action
Heating or cooling
come on
momentarily and
shut off
Heat or cool circuit is opening
up or becoming high
impedance.
Add resistor in parallel with load or install interface relay.
System on indicator
(flame=heat,
snowflake=cool) is
displayed, but no
Fan operation set for 0
(conventional heat) when it
should be set for 1 (electric
heat).
Enter Installer Setup number 2 and reconfigure the fan operation.
warm or cool air is
coming from the
registers.
Conventional heating
equipment turns on the fan
when the furnace has
warmed up to a setpoint.
Wait a minute after seeing the on indicator and then check the registers.
Heating or cooling equipment is
not operating. Verify operation of heating or cooling equipment in self-test.
Outdoor
temperature not
displayed
a
Option not activated. Enter Installer Setup number 24 and set to 1. Thermostat must have OT
terminals and a C7089B1000 installed.
Outdoor
temperature
Outdoor sensor is connected
incorrectly. Refer to C7089B1000 installation instructions and check wiring between
the thermostat and sensor.
display is incorrect
a
Wrong sensor. Replace sensor with C7089B1000 sensor.
a
Available on select models.
Feature/Function Chronotherm® III Family Chronotherm® IV Family
Programming 5-1-1 day programming 7-day programming
Changeover Automatic or manual changeover models
available Automatic/manual changeover selectable
Installer configuration Field settings made via screws on the back of
the thermostat Field settings made through the keyboard
System switching Mechanical switch Keyboard entry
Fan switching Mechanical switch Keyboard entry
Device color Beige or Premier White® color Taupe or Premier White® color
CROSS REFERENCE
All SUPER TRADELINE® Chronotherm® IV thermostats are
different from the existing Chronotherm® III devices as
summarized in Table 13.
Refer to Table 14 for thermostat cross referencing information.
Table 13. Differences Between Chronotherm® III Thermostats and Chronotherm® IV Thermostats.
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1 20
(continued)
Model Number Description TRADELINE®
Replacement Remarks
T8600A One-stage heat conventional thermostat; system powered; system switch—none;
fan switch—none.
T8600A1000 Honeywell logo. T8600D2028 Heat/cool model can be used for heat
only; system selection Heat-Off-Cool-
Auto; duel fuel.
T8600A1018 Canadian TRADELINE® thermostat;
Honeywell logo; degree C.
T8600D2028 Heat/cool model can be used for heat
only; system selection Heat-Off-Cool-
Auto; configure for °C in Installer Setup
14; duel fuel.
T8600A1034 Canadian TRADELINE® thermostat;
Honeywell logo; Premier White® color;
degree C.
T8600D2028 Heat/cool model can be used for heat
only; system selection Heat-Off-Cool-
Auto; configure for °C in Installer Setup
14; duel fuel.
T8600B One-stage heat and one-stage cool conventional thermostat; system powered
T8600B1008 TRADELINE® thermostat; Honeywell logo;
system switch—HEAT-OFF; fan
switch—none.
T8600D2028 Heat/cool model can be used for heat
only; system selection Heat-Off-Cool-
Auto; fan selection On-Auto; duel fuel;
no positive off.
T8600B1016 TRADELINE® thermostat; Honeywell logo;
system switch—none; fan
switch—ON-AUTO.
T8600D2028 Heat/cool model can be used for heat
only; system selection Heat-Off-Cool-
Auto; duel fuel.
T8600C One-stage heat and one-stage cool thermostat; system powered; system switch—HEAT-OFF-
COOL; fan switch—ON-AUTO
T8600C1014 TRADELINE® thermostat; Honeywell logo;
conventional. T8600D2028 Separate O & B terminals; duel fuel.
T8600C1030 Canadian TRADELINE® thermostat;
Honeywell logo; conventional; degree C;
O and B terminals.
T8600D2028 Configure for °C in Installer Setup 14;
duel fuel; jumper R to Rc.
T8600C1048 York logo; conventional; part no.
2ET07700124A. T8600D2028 Separate O & B terminals; duel fuel.
T8600C1055 Canadian TRADELINE® thermostat;
Honeywell logo; conventional; degree C.
T8600D2028 Configure for °C in Installer Setup 14;
duel fuel; jumper R to Rc.
T8600C1063 Trane logo; conventional; part no.
THT0594. T8600D2028 Separate O & B terminals; duel fuel.
T8600C1071 Trane logo; electric heat; O and B
terminals; part no. THT0595. T8600D2028 Configure for electric heat in Installer
Setup 2; jumper R to Rc.
T8600C1089 Texfan logo; conventional. T8600D2028 Separate O & B terminals; duel fuel.
T8600C1097 Glowcore logo; conventional; part no.
THC-3. T8600D2028 Separate O & B terminals; duel fuel.
T8600C1105 York logo; conventional; part no. 025-27653
and 2ET0770224A. T8600D2028 Separate O & B terminals.
T8600C1113 Canadian York thermostat; conventional;
degree C.
T8600D2028 Separate O & B terminals; configure for
°C in Installer Setup 14; duel fuel.
T8600C1121 Arcoaire logo; conventional: part no.
1506-745. T8600D2028 Separate O & B terminals; duel fuel.
T8600C1147 Trane logo; conventional; part no.
TAYSTAT300. T8600D2028 Separate O & B terminals; duel fuel;
jumper R to Rc.
T8600C1154 American Standard logo; conventional;
part no. ASYSTAT600. T8600D2028 Separate O & B terminals; duel fuel;
jumper R to Rc.
T8600C1162 SUPER TRADELINE® thermostat;
Honeywell logo; duel fuel fan control; O and
B terminals.
T8600D2028 Jumper R to Rc.
Table 14. Thermostat Cross Reference Information.
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1
21
Table 14. Thermostat Cross Reference Information. (continued)
(continued)
Model Number Description TRADELINE®
Replacement Remarks
T8600C1170 Carrier thermostat; conventional; part no.
HH07AX006. T8600D2028 Separate O & B terminals; duel fuel;
jumper R to Rc.
T8600C1188 Carrier thermostat; conventional; part no.
HH641-101. T8600D2028 Separate O & B terminals; duel fuel;
jumper R to Rc.
T8600C1196 Canadian TRADELINE® thermostat;
Honeywell logo; Premier White® color;
conventional; degree C.
T8600D2028 Separate O & B terminals; configure for
°C in Installer Setup 14; duel fuel;
jumper R to Rc.
T8600C1204 Canadian Lennox thermostat; conventional;
degree C.
T8600D2028 Separate O & B terminals; configure for
°C in Installer Setup 14; duel fuel;
jumper R to Rc.
T8600C1212 SUPER TRADELINE® thermostat;
Honeywell logo; duel fuel fan control; O and
B terminals.
T8600D2028 Jumper R to Rc; taupe color.
T8600C1220 Servel logo; Premier White® color;
conventional; Robur part no. 15471-82. T8600D2028 Separate O & B terminals; duel fuel;
taupe color.
T8600C1238 ICP logo; Premier White® color; duel fuel
fan control; O and B terminals; part no.
HQ1149371HW.
T8600D2028 Jumper R to Rc; taupe color.
T8600C1246 ICP logo; Premier White® color; duel fuel
fan control; O and B terminals; part no.
HQ1149372HW.
T8600D2028 Jumper R to Rc; taupe color.
T8600C1253 Consolidated Industries logo; Premier
White® color; conventional; part no.
412360.
T8600D2028 Separate O & B terminals; duel fuel;
taupe color.
T8600C1279 Canadian TRADELINE® (French)
thermostat; conventional. T8600D2028 English only keyboard; separate O & B
terminals; duel fuel.
T8600D One-stage heat and one-stage cool conventional thermostat; system powered; automatic
changeover; system switch— HEAT-OFF-COOL-AUTO; fan switch— ON-AUTO
T8600D1004 TRADELINE® thermostat; Honeywell logo. T8600D2028 Separate O & B terminals; duel fuel.
T8600D1012 Canadian TRADELINE® thermostat;
Honeywell logo; degree C.
T8600D2028 Separate O & B terminals; configure for
°C in Installer Setup 14; duel fuel.
T8600D1020 Energy Sensor. T8600D2028 Separate O & B terminals; duel fuel.
T8600D1038 Canadian Carrier thermostat; degree C;
part no. HH07AT101. T8600D2028 Separate O & B terminals; configure for
°C in Installer Setup 14; duel fuel;
T8600D1046 Trane. T8600D2028 Separate O & B terminals; duel fuel.
T8600D1053 Heil Quaker thermostat; Honeywell logo;
part no. HQ1000776HW. T8600D2028 Separate O & B terminals; duel fuel.
T8600D1061 Carrier. T8600D2028 Separate O & B terminals; duel fuel.
T8600D1079 Lennox logo; part no. 27H3101. T8600D2028 Separate O & B terminals; duel fuel.
T8600D1103 Carrier. T8600D2028 Separate O & B terminals; duel fuel.
T8600D1111 TRADELINE® thermostat; Honeywell logo;
Premier White® color. T8600D2028 Separate O & B terminals; duel fuel;
taupe color.
T8600D1129 Canadian TRADELINE® thermostat;
Honeywell logo; Premier White® color;
degree C.
T8600D2028 Separate O & B terminals; configure for
°C in Installer Setup 14; duel fuel.
T8600D1137 Solitaire logo; Premier White® color;
Nordyne part no. 9132400. T8600D2028 Separate O & B terminals; duel fuel;
taupe color.
T8600D1145 Canadian Carrier thermostat; Premier
White® color; degree C; part no.
HH07AT101-W.
T8600D2028 Separate O & B terminals; configure for
°C in Installer Setup 14; duel fuel.
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1 22
Table 14. Thermostat Cross Reference Information. (continued)
(continued)
Model Number Description TRADELINE®
Replacement Remarks
T8601A One-stage conventional heat thermostat; powered direct from 24 Vac transformer
T8601A1017 Canadian TRADELINE® thermostat;
Honeywell logo; system switch—none;
fan switch—none; degree C.
T8601D2019 Heat/cool model can be used for heat
only; system selection Heat-Off-Cool-
Auto; configure for °C in Installer Setup
14; Premier White® color.
T8601B One-stage conventional heat with fan thermostat; powered direct from 24 Vac transformer
T8601B1007 TRADELINE® thermostat; Honeywell logo;
system switch—none; fan
switch—ON-AUTO .
T8601D2019 Heat/cool model can be used for heat
only; system selection Heat-Off-Cool-
Auto; jumper R to Rc for fan control;
Premier White® color.
T8601C One-stage heat and one-stage cool conventional thermostat; powered direct from 24 Vac
transformer; system switch—HEAT-OFF-COOL; fan switch—ON-AUTO; O and B terminals
T8601C1003 TRADELINE® thermostat; Honeywell logo. T8601D2019 Jumper R to Rc; Premier White® color.
T8601C1013 Canadian TRADELINE® thermostat;
Honeywell logo; degree C.
T8601D2019 Configure for °C in Installer Setup 14;
jumper R to Rc; Premier White® color.
T8601C1021 New Construction thermostat. T8601D2019 Jumper R to Rc; Premier White® color.
T8601C1039 Carrier logo; part no. HH641-104. T8601D2019 Jumper R to Rc; Premier White® color.
T8601C1047 New Construction thermostat; Premier
White® color. T8601D2019 Jumper R to Rc.
T8601C1054 Trol-A-Temp® thermostat; Premier White®
color. T8601D2027
a
Configure manual changeover in
Installer Setup12; replacement has Oc
terminals.
T8601C1062 Trol-A-Temp® by Honeywell logo. T8601D2027
a
Configure manual changeover in
Installer Setup12; replacement has Oc
terminals; Premier White® color.
T8601D One-stage heat and one-stage cool conventional thermostat; powered direct from 24 Vac
transformer; automatic changeover; system switch—HEAT-OFF-COOL-AUTO; fan switch—ON-
AUTO
T8601D1011 Canadian TRADELINE® thermostat;
Honeywell logo; degree C.
T8601D2019 Separate O & B terminals; configure for
°C in Installer Setup 14 and
changeover in 12; jumper R to Rc;
Premier White® color.
T8601D1029 New Construction thermostat. T8601D2019 Separate O & B terminals; configure
changeover in Installer Setup 12;
jumper R to Rc; Premier White® color.
T8601D1045 Trol-A-Temp® by Honeywell thermostat;
Premier White® color. T8601D2027
a
Separate O & B terminals; replacement
has Oc terminals.
T8601D1052 New Construction thermostat; Premier
White® color. T8601D2019 Separate O & B terminals; configure
changeover in Installer Setup 12;
jumper R to Rc.
T8601D1060 California Economizer logo; Premier
White® color. T8601D2019 Separate O & B terminals; configure
changeover in Installer Setup 12;
jumper R to Rc.
T8601D1078 Amana logo; Premier White® color;
part no. P1213701F. T8601D2019 Separate O & B terminals; configure
changeover in Installer Setup 12;
jumper R to Rc.
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1
23
Table 14. Thermostat Cross Reference Information. (continued)
(continued)
Model Number Description TRADELINE®
Replacement Remarks
T8602A One-stage heat conventional thermostat; battery powered; system switch—none; fan switch—
none
T8602A1008 TRADELINE® thermostat; Honeywell logo. T8602D2000 Heat/cool model can be used for heat
only; separate O & B terminals; system
selection Heat-Off-Cool-Auto; fan
selection Auto-On.
T8602B One-stage heat conventional with fan thermostat; battery powered; system switch—none; fan
switch—ON-AUTO
T8602B1006 TRADELINE® thermostat; Honeywell logo. T8602D2000 Heat/cool model can be used for heat
only; separate O & B terminals; system
selection Heat-Off-Cool-Auto; fan
selection Auto-On; jumper R to Rc for
fan operation.
T8602B1014 TRADELINE® thermostat; Honeywell logo;
Premier White® color. T8602D2000 Heat/cool model can be used for heat
only; separate O & B terminals; system
selection Heat-Off-Cool-Auto; fan
selection Auto-On; jumper R to Rc for
fan operation; taupe color.
T8602C One-stage heat and one-stage cool thermostat; battery powered; system switch—HEAT-OFF-
COOL; fan switch—ON-AUTO
T8602C1004 TRADELINE® thermostat; Honeywell logo. T8602D2000 Separate O & B terminals; jumper R to
Rc.
T8602C1012 Amana logo; conventional; part no.: none. T8602D2000 Separate O & B terminals; jumper R to
Rc.
T8602C1020 Rheem logo; conventional; part no.: none. T8602D2000 Separate O & B terminals; jumper R to
Rc.
T8602C1046 SUPER TRADELINE® thermostat;
Honeywell logo; duel fuel fan control; O and
B terminals.
T8602D2000
T8602C1061 Trol-A-Temp® by Honeywell thermostat;
Premier White® color; conventional; O and
B terminals.
T8602C2051
a
T8602C1079 Trol-A-Temp® by Honeywell thermostat;
conventional; O and B terminals. T8602C2051
a
Premier White® color.
T8602C1095 SUPER TRADELINE® thermostat;
Honeywell logo; Premier White® color; duel
fuel fan control; O and B terminals.
T8602D2000 Taupe color.
T8602C1103 Canadian TRADELINE® thermostat;
Honeywell logo; duel fuel fan control;
degree C; O and B terminals.
T8602D2000 Configure for °C in Installer Setup 14 .
T8602C1129 Universal Parts logo; Rheem part no.
41-21615-05; conventional. T8602D2000
T8602C1137 ICP logo; duel fuel fan control; O and B
terminals; part no. HQ1149373HW. T8602D2000
T8602C1145 ICP logo; Premier White® color; duel fuel
fan control; O and B terminals;
part no. HQ1149374HW.
T8602D2000 Taupe color.
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1 24
Table 14. Thermostat Cross Reference Information. (continued)
L1
(HOT)
L2
M10346
FAN
RELAY
G
THERMOSTAT
HEAT
RELAY
RW
TRANSFORMER
POWER SUPPLY. PROVIDE DISCONNECT MEANS AND
OVERLOAD PROTECTION AS REQUIRED.
NOT AVAILABLE ON T8600A MODELS.
1
2
1
2
L1
(HOT)
L2
M10347
FAN
RELAY
YG
THERMOSTAT
HEAT
RELAY
RW
COMPRESSOR
CONTACTOR
TRANSFORMER
B
HEAT
DAMPER
COOL
DAMPER
O
1POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD
PROTECTION AS REQUIRED.
CAN BE USED FOR CHANGEOVER VALVE ON SINGLE-STAGE HEAT
PUMP SYSTEMS.
AVAILABLE ON SELECT MODELS. OT WIRES MUST HAVE A
SEPARATE CABLE FROM THE THERMOSTAT CABLE.
2
2
2
1
3
OTOT
OUTDOOR
TEMPERATURE
SENSOR
3
3
Model Number Description TRADELINE®
Replacement Remarks
T8602D One-stage heat and one-stage cool conventional thermostat; battery powered; automatic
changeover
T8602D1010 Trol-A-Temp® by Honeywell thermostat;
Premier White® color; system
switch—none; fan switch—none; field
terminals: W/4, R/5, Y/6.
T8602D2026a
T8602D1028 Trol-A-Temp® by Honeywell thermostat;
system switch—none; fan switch—none;
field terminals: W/4, R/5, Y/6.
T8602D2026aPremier White® color.
CT8602C One-stage heat and one-stage cool retail thermostat battery powered
CT8602C1001 Retail Honeywell logo; off-white color; duel
fuel fan control; system switch HEAT-OFF-
COOL; fan switch ON-AUTO; separate O
and B terminals; clamshell packaging.
T8602D2000 TRADELINE® packaging.
aTrol-A-Temp® by Honeywell thermostat model.
WIRING DIAGRAMS (Fig. 15-20)
Fig. 15. Typical hookup of T8600 or T8602
in heat only application.
Fig. 16. Typical hookup of T8600 or T8602 in heat and cool
system with one transformer.
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1
25
L1
(HOT)
L2
M10348
FAN
RELAY
YG
THERMOSTAT
RC
HEAT
RELAY
RW
L1
(HOT)
L2
COMPRESSOR
CONTACTOR
HEATING
TRANSFORMER
COOLING
TRANSFORMER
B
HEAT
DAMPER
COOL
DAMPER
O
2
1POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD
PROTECTION AS REQUIRED.
JUMPER RC TERMINAL TO R TERMINAL WHEN INSTALLED ON A
ONE TRANSFORMER SYSTEM.
CAN BE USED FOR CHANGEOVER VALVE ON SINGLE-STAGE HEAT
PUMP SYSTEMS.
AVAILABLE ON SELECT MODELS. OT WIRES MUST HAVE A
SEPARATE CABLE FROM THE THERMOSTAT CABLE.
T8600D MODELS REQUIRE POWER TO R TERMINAL AT ALL TIMES.
2
3
3
1
1
3
4
OTOT
OUTDOOR
TEMPERATURE
SENSOR
4
4
5
5
L1
(HOT)
L2
M10357
FAN
RELAY
GC
THERMOSTAT
HEAT
RELAY
RW
TRANSFORMER
POWER SUPPLY. PROVIDE DISCONNECT MEANS AND
OVERLOAD PROTECTION AS REQUIRED.
NOT AVAILABLE ON "A" MODELS.
1
2
1
2
Fig. 17. Typical hookup of T8600 or T8602 in heat and
cool system with two transformers.
Fig. 18. Typical hookup of T8601 in heat only application.
Fig. 19. Typical hookup of T8601 in heat
and cool system with one transformer.
Fig. 20. Typical hookup of T8601 in heat
and cool system with two transformers.
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1 26
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1
27
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1 28
Honeywell Europe S.A.
3 Avenue du Bourget
B-1140 Brussels Belgium
Honeywell Asia Pacific Inc.
Room 3213-3225
Sun Hung Kai Centre
No. 30 Harbour Road
Wanchai
Hong Kong
Home and Building Control
Honeywell Limited-Honeywell Limitée
155 Gordon Baker Road
North York, Ontario
M2H 3N7
Honeywell Latin American Region
480 Sawgrass Corporate Parkway
Suite 200
Sunrise FL 33325
Helping You Control Your World®
68-0164—1 J.H. Rev. 7-97 Printed in U.S.A. www.honeywell.com/yourhome
Home and Building Control
Honeywell Inc.
Honeywell Plaza
P.O. Box 524
Minneapolis MN 55408-0524
Printed on recycled paper containing at
least 10% post-consumer paper fibers.

Navigation menu