USER'S GUIDE REV AA Tabber User Parts

User Manual: Tabber User Parts

Open the PDF directly: View PDF .
Page Count: 175

Download
Open PDF In Browser	View PDF

User’s Guide

MCSPRO-1020
Tabbing System

MCS Incorporated
8101 Cessna Avenue
Gaithersburg, MD 20879

REV-AA

MCSPRO-1020 Tabbing System User’s Guide

Table of Contents
Chapter 1 - System Description....................................................................................................... 5
Chapter 2 - System Components ..................................................................................................... 7
2.1 Transport Base Component ................................................................................................... 7
2.2 Tabbing Head Component ..................................................................................................... 8
Chapter 3 - Electronic Controls....................................................................................................... 9
3.1 Transport Control Panel......................................................................................................... 9
3.1.1 Base Power Rocker Switch ............................................................................................. 9
3.1.2 Head Power Rocker Switch............................................................................................. 9
3.1.3 Jog Push Button Switch .................................................................................................. 9
3.1.4 Start Push Button Switch ................................................................................................ 9
3.1.5 Transport Speed Potentiometer ....................................................................................... 9
3.2 Operator Interface .................................................................................................................. 9
3.2.1 LCD Module ................................................................................................................. 10
3.2.2 Online Key .................................................................................................................... 10
3.2.3 Menu Scroll Keys.......................................................................................................... 10
3.2.3.1 Product Count......................................................................................................... 10
3.2.3.2 Transport Speed...................................................................................................... 11
3.2.3.3 Production Rate ...................................................................................................... 11
3.2.4 Numeric Keypad ........................................................................................................... 11
3.2.5 Menu Selection Keys .................................................................................................... 11
3.3 Stop Switch (Red Mushroom Cap) .................................................................................... 11
Chapter 4 – System Setup ............................................................................................................. 13
4.1 Base Set-up .......................................................................................................................... 13
4.1.1 Position Transport Base ............................................................................................... 13
4.1.2 Position Base................................................................................................................ 14
4.1.3 Ink Jet Base Setup ........................................................................................................ 15
4.1.4 Adjust Transport Table Position .................................................................................. 15
4.1.5 Product Guide and Strap Usage ................................................................................... 16
4.1.6 Set Gap ......................................................................................................................... 17
4.1.7 Power-Up System......................................................................................................... 18
4.1.8 Feed Product................................................................................................................. 18
4.1.9 Adjust Registration Wheels.......................................................................................... 18
4.1.10 Output Drive Wheels.................................................................................................. 21
4.1.11 Center Belt Adjustment.............................................................................................. 22
4.1.12 Position Upper Press Rolls......................................................................................... 23
4.1.13 Idler Wheel Adjustments............................................................................................ 24
4.2 Head Set-up ......................................................................................................................... 27
4.2.1 Install Inner Spool Guides............................................................................................ 27
4.2.2 Secure Source Spool .................................................................................................... 27
4.2.3 Threading ..................................................................................................................... 27
4.2.4 Secure Waste Take-up Spool ....................................................................................... 27
4.2.5 Adjust Tab Sensor ........................................................................................................ 28
4.2.6 Adjust Pitch Setting...................................................................................................... 28
4.2.7 Select Product Sensor................................................................................................... 29
4.2.8 Tab/ Label Position Entry ............................................................................................ 29
4.2.9 Number of Tabs............................................................................................................ 30
4.2.10 Begin Tabbing............................................................................................................ 31
Chapter 5 - Controller Programming/Diagnostics......................................................................... 33
5.1 Setup Programming ............................................................................................................ 33
5.1.1 Pitch Setting ................................................................................................................. 33
5.1.2 Save Setup to Memory ................................................................................................. 33
5.1.3 Auto Tab Calculator Product Size................................................................................ 34
5.1.4 Product/ Tab Sensor Offset .......................................................................................... 34
MCSPRO-1020 Tabbing System User’s Guide

5.3.5 Tab Sensor Sensitivity.................................................................................................. 35
5.3.6 Counter Reset ............................................................................................................... 35
5.3.7 Product Sensor Selection.............................................................................................. 36
5.2 Position Programming ........................................................................................................ 36
5.2.1 Tab/ Label Position Entry ............................................................................................ 36
5.2.2 Number of Tabs............................................................................................................ 37
5.4 Head Diagnostics/ Test ....................................................................................................... 38
5.4.1 Software Version.......................................................................................................... 38
5.4.2 Tab Drive Cycle Test ................................................................................................... 39
5.4.3 Stop Relay Test ............................................................................................................ 39
5.4.4 Motor/ Brake Test ........................................................................................................ 39
5.4.5 Base Cover Test ........................................................................................................... 40
5.4.6 Head Cover Test........................................................................................................... 40
5.4.7 Bin Sensor Test ............................................................................................................ 40
5.4.8 Take-up Sensor Test..................................................................................................... 41
5.4.9 Left Product Sensor Test .............................................................................................. 41
5.4.10 Right Product Sensor Test.......................................................................................... 41
5.4.11 Tab/ Label Sensor Test............................................................................................... 42
5.4.12 Encoder Test............................................................................................................... 42
5.4.13 Factory Reset.............................................................................................................. 42
Chapter 6 – Troubleshooting ......................................................................................................... 43
Chapter 7 – Appendix.................................................................................................................... 45
FIGURE A1 – BASE CONTROL SYSTEM DIAGRAM ........................................................ 45
FIGURE A2 – HEAD CONTROL SYSTEM DIAGRAM ....................................................... 46
FIGURE A3 – HEAD SYSTEM DIAGRAM ........................................................................... 47
ILLUSTRATED PART BREAKDOWN .................................................................................. 48
MISCELANIOUS SPARE PARTS NOT LISTED ABOVE .................................................... 55

MCSPRO-1020 Tabbing System User’s Guide

Chapter 1 - System Description
The MCSPRO-1020 Tabbing System is designed to apply pressure sensitive tabs/ labels on to flat
product. You can use the system as a wrap around tabbing device or use it as a labeler. The
system is made up of two major components, the transport base and the tabbing head. The tabbing
head is movable to enable tabbing on either edge of a mail piece. If the system is used as a flat
tabber or labeler, the head can be located to position the label anywhere on the piece. Tab/ Label
position over the length of the product is adjusted electrically through the operator interface.
The product is introduced into the system by a feeder, conveyor, or ink jet system. The product is
justified to a side guide by adjusting the transport table position and the registration wheel
assembly. A knob that raises and lowers the height of the tabbing head and the upper output
transport assembly adjusts for product thickness.
When the product is transported, it is detected by a through-beam sensor that tells the tabbing
head to apply a tab. If more than one tab is to be applied to a product, this can be set at the
operator interface. After the tab is applied, the product passes through a number of rollers and
guides to ensure that the tab/label is firmly applied and wrapped tight against the product edge.

MCSPRO-1020 Tabbing System User’s Guide

Chapter 2 - System Components
2.1 Transport Base Component
The transport base is designed to register and tightly control the product for accurate and
consistent tab/ label application. When it is used to apply tabs (wafer seals) to the edge of mail
pieces it is also responsible for wrapping the tab around the piece. All electrical controls are
found on the transport base. The major components of the transport base are shown in Figure 1.

FIGURE 1 – TRANSPORT BASE

MCSPRO-1020 Tabbing System User’s Guide

2.2 Tabbing Head Component
The tabbing head is designed for accurate and high-speed application of pressure sensitive
tabs/ labels. It was designed specifically to work in conjunction with the base and is controlled
by the interfaces on the base. The major components of the head are shown in Figure 2.

FIGURE 2 - TABBING HEAD

MCSPRO-1020 Tabbing System User’s Guide

Chapter 3 - Electronic Controls
3.1 Transport Control Panel
The Transport Control Panel is located on the left side of the base front. This panel controls
system power and transport base motor condition. Housed on this panel are the following six
controls:
•
•
•
•
•

Base Power Rocker Switch
Head Power Rocker Switch
Jog Push Button Switch
Start Push Button Switch
Transport Speed Potentiometer

3.1.1 Base Power Rocker Switch
This switch controls power to the tabber base. This switch must be on and lit in order for the
transport base to function.

3.1.2 Head Power Rocker Switch
This switch controls power to the tabbing head. This switch must be on and lit in order for the
tabbing head to function. Since this switch obtains its power from the base, the Base Power
Rocker Switch must also be on.

3.1.3 Jog Push Button Switch
This switch is provided to aid operator setup. When depressed the transport base motor will run
at the speed set by the speed control pot. The base will stop as soon as the switch is released.
3.1.4 Start Push Button Switch
This switch is used to start the transport base motor. The transport base motor will run at the
speed set by the speed control until the Stop Mushroom Cap Switch is depressed or the electronic
controls stop the unit.
3.1.5 Transport Speed Potentiometer
The transport speed potentiometer is used to control the speed of the base. Turning this knob
clockwise will increase base speed.

3.2 Operator Interface
MCSPRO-1020 Tabbing System User’s Guide

The Operator Interface is located on the right side of the base front. It is used to setup and control
the tabbing head and consists of an array of tact-switches and a LCD display. The Operator
Interface can be subdivided into the following 5 sections:
• LCD Module
• Online Key
• Menu Scroll Keys
• Numeric Keypad
• Menu Selection Keys

SETUP

MEMORY

ONLINE

ENTER

TEST

POSITION

FIGURE 3 - OPERATOR INTERFACE
3.2.1 LCD Module
The Operator Interface is equipped with a LCD module used to display controller information to
the operator. Setup parameters, error descriptions and controller status can all be viewed through
the LCD.
3.2.2 Online Key
This key toggles the head condition between online and offline. When offline the head will not
dispense any tabs/ labels. The head must be offline to access setup parameters within the
controller. The head must be online in order to dispense tabs/ labels. Online/ Offline condition is
displayed on the LCD. While online the second line of the LCD displays “NORMAL STATUS”,
if offline the first line of the LCD displays “OFFLINE”.
3.2.3 Menu Scroll Keys
The (up arrow) and (down arrow) keys are used to scroll up and down menus to facilitate
menu item selection when used during setup. These keys are also used to control the display of
production data when the unit is online. The operator can choose between the following three
different production displays:
• Product Count
• Transport Speed
• Production Rate
3.2.3.1 Product Count
The controller maintains a six-digit product count. The operator through use of the setup key can
reset this counter. An example of a typical count display follows.
FORMS DONE: 000123
NORMAL STATUS

MCSPRO-1020 Tabbing System User’s Guide

3.2.3.2 Transport Speed
The controller must be aware of the transport speed to accurately locate tabs/ labels on the
product. This speed, displayed in feet/ minute, represents the approximate belt speed of the base.
An example of a typical speed display follows.
SPEED: 160 FT/M
NORMAL STATUS
3.2.3.3 Production Rate
Another useful production item is the production rate. The controller can display the approximate
real-time production rate of the tabber. Units for the production rate is product #/ hour. An
example of a typical rate display follows.
PROD RATE: 24000 PPH
NORMAL STATUS
3.2.4 Numeric Keypad
A numeric keypad is provided to allow direct entry of settings from the Operator Interface. This
keypad is functional for tabber setup only when the unit is offline.
3.2.5 Menu Selection Keys
Beneath the LCD are four menu selector keys. These keys are used to access the different setup
and test menus. The four keys are listed below:
• Test
• Position
• Setup
• Mode

3.3 Stop Switch (Red Mushroom Cap)
When depressed, this switch stops the transport base motor. If the stop interlock cable has been
used to “tie-in” the tabber with the feeding equipment, then the stop switch will also stop the infeeding equipment. The operator must twist the switch in order to release the stop condition.

MCSPRO-1020 Tabbing System User’s Guide

Chapter 4 – System Setup
4.1 Base Set-up
4.1.1 Position Transport Base
The Tabbing Base is designed with two sections, lower fixed base and upper sliding transport
table. The sliding transport table allows tabbing or labeling on the operator or non-operator side.
Requirement:
Adjust transport table to begin system setup.
Procedure:
1.
2.

Loosen transport table locking lever. (See Figure 5)
Position transport table to dimension given. (See Figure 4)

Figure 4

MCSPRO-1020 Tabbing System User’s Guide

4.1.2 Position Base
The Tabbing Base has casters to move the system. Roll the input end of the base up to the output
end of the ink jet base.
Requirement:
Position base to ink jet base for product transition and centerline.
Procedure
1.
2.
3.
4.

5.
6.

Loosen the four height adjust lock screws (Figure 5)
Adjust two height adjust screws up-down until bridge angle (Figure 5) is just below the
belts of the ink jet base.
Secure the four height adjust locking screws.
Position tabber base so the bridge angle is as close to ink jet base belts without touching
and position tabber base so the centerline of ink jet base matches the centerline of the
transport table (Figure 6).
Set four leveling pads (Figure 5) firmly to secure tabber base in final position.
Secure leveling pad lock nuts against base bottom.

Figure 5

MCSPRO-1020 Tabbing System User’s Guide

FIGURE – 6

4.1.3 Ink Jet Base Setup
All requirements concerning feeding, printing and product position should be met before feeding
product through tabber.

4.1.4 Adjust Transport Table Position
Requirement:
Adjust transport table to edge of product path.
Procedure:
1.
2.
3.

Feed product from ink jet base to transport table until it just crosses bridge angle. Stop
feed.
Loosen table lever lock (See Figure 5). Position transport table guide rail 1/8” from
product edge (See Figure 7). Lock table lever.
Use fine adjust knob (See Figure 5) to complete the adjustment if necessary. The fine
adjustment may also be used as a running adjustment to move guide rail towards or away
from product edge during operation.

MCSPRO-1020 Tabbing System User’s Guide

Figure 7

4.1.5 Product Guide and Strap Usage
Procedure:
1.

Mount strap assemblies (2) provided to square shaft (See Figure 8).

Note: Straps may be positioned on product to control flatness as desired or removed by loosening
screw and rotating retainer cap 180 degrees.
2.

Mount Product Guide (See Figure 9).

Note: The product guide is provided primarily for use in off line requirements when auxiliary
feeders are used. Its purpose is to control product skew that may be experienced using freestanding feeders, normally friction type. Skew is not normally experienced with in line ink jet
base use, however guide use may be desirable. The guide is designed with an oversized slot in
the mounting block. The assembly may be positioned on any angle to allow entry of skewed
product and correct it as it proceeds.
Note: The product guide may be mounted on either side of the mounting block to allow use on
both the operator’s side or non-operator’s side. Remove (2) screws (See Figure 9) and
reposition guide using the two additional holes provided, on the opposite side of the mounting
block.

MCSPRO-1020 Tabbing System User’s Guide

Strap Assemblies
Screws

Figure 9

Figure 8

4.1.6 Set Gap
The tabbing/labeling system can accept flat product as thick as 5/8 inch. The Product Thickness
Adjust Crank controls the gap. Rotate clockwise to increase gap, counterclockwise to decrease
gap.

Requirement:
The top wrap section must be gapped to product thickness to effectively wrap tabs or secure
labels.
Procedure:
1.

Rotate Product Thickness Crank (See Figure 10) clockwise. Insert product sample to be
tabbed between upper output belt and output roller below.

Rotate crank counterclockwise until firm pressure is felt by pulling product sample from
the belt-roller.

Figure 10

MCSPRO-1020 Tabbing System User’s Guide

4.1.7 Power-Up System
The tabber control system depends on a small computer processor for its operation. Since
electrical line disturbances can adversely affect computers it would be prudent to use a “fairly
clean” line to power the tabber. Plug the power cord into a 120VAC 60Hz source. Power-up the
base by turning on only the Base Power Rocker Switch. The switch will light up as a
confirmation of power application.

4.1.8 Feed Product
Start the base by pressing the Start Pushbutton and adjusting the Speed Control Knob until the
speed of tabbing/labeling base matches the speed of the system feeding it. Feed sample product
to make sure it enters the transport within 1/8” of the guide rail.

4.1.9 Adjust Registration Wheels
The tabbing/labeling base uses a set of registration wheels to ensure consistent placement and
wrap of tabs and labels. The wheels are used to “push” the product against the guide rail guide
and secure the product to the transport belt. The first three entry wheels are slaved together on a
swivel system that allows angle adjustment to drive the product against the guide rail for
registration. The following three drive wheels are fixed in a straight line to maintain registration
along the guide rail for accurate tab/label placement on the product.
This registration wheel assembly is designed to function on either side of the transport base. The
assembly may be positioned over any portion of the lower transport belts along the square
mounting shafts, by loosening lever locks and sliding to desired location. Drive pressure may be
increased or decreased by rotating the Wheel Lift Knob. This knob is also used to lift the
complete assembly off the lower transport belts for repositioning. The Registration Wheel
Assembly functions best when product is delivered 1/8” or less from the guide rail at the entry
point. (See Figure 7 of Section 4.1.4)
Warning: Product feeding and registration must be properly adjusted before tabbing! Turn
head power off and move the head aside. Visually check feeding and registration with sample
product. Any skew or catch points must be eliminated. A Product Guide and two Hold Down
Straps are provided to control the conditions above (See Section 4.1.5)) at the input end of
tabber. The primary feeder, free standing friction type, ink jet base friction or vacuum, must
also be properly adjusted to eliminate double feeds, product skew or side to side drift.
Requirement:
Registration wheels must be positioned and adjusted to consistently guide product edge along
guide rail, without distorting or causing product stall.
Note: A fine adjustment limit stop (Figure 13) is provided to control and maintain drive
pressure. Turning the knob clockwise limits the down-drive pressure. Turning the knob
counterclockwise allows more down-drive pressure to be set. The limit stop allows the assembly
to be raised completely from a preset drive position and returned to that position without
adjustments.

MCSPRO-1020 Tabbing System User’s Guide

Procedure:
1.

Loosen lever locks (See Figure 11). Position registration wheel assembly over belt
adjacent to guide rail.

Adjust angle drive wheel knob to angle three slaved wheels towards guide rail (See Figure
11). Do not adjust wheels to maximum angle. Use minimum angle, increase only as
necessary.

Note: Occasionally it may be necessary to angle the entire registration system. (See Figure 12)
to assure product remains against guide rail. The lever lock mounting assemblies permit a limited
amount of misalignment for this purpose.
Caution:
Over adjustment of angle wheels and excessive drive pressure can cause product to ride up guide
rail, or cause product to distort or stall. A deflector strip (Figure 13) is provided along each guide
rail to help hold down product.
3.

Turn base power on and operate base with speed control at slow speed. Rotate drive
wheel lift knob (Figure 11) counterclockwise until all drive wheels are turning. Turn fine
adjustment knob screw clockwise to meet stop on square shaft (Figure 12).

Feed product and visually check to assure product is against the guide rail and not
distorted or stalling before entering underneath upper press roll. Further adjust angle
wheels and drive wheel down pressure if necessary. Operate at production speed and
visually check again.

When the requirements above have been met, tabbing operation can proceed.

Warning: For pass thru operation (Not applying tabs), set up as described above. Product
conveyed by tabber transport belts only, and not controlled by top drive, can skew and migrate
into the gearbelts of the upper wrap section. Severe damage or breakage can occur! When the
tabber base is left in-line and used as a conveyor, the same set up procedures for tabbing,
labeling or stamp affixing must be used. However, since securing tabs, labels or stamps to the
product is not a requirement, the gap setting (See Section 4.1.5) may be opened slightly more
than normal for product flow.

MCSPRO-1020 Tabbing System User’s Guide

Figure 12

Figures 11 & 12

Fine Adjust Limit Stop Knob
Deflector Strip

Wheel Lift Knob

Figure 13

MCSPRO-1020 Tabbing System User’s Guide

4.1.10 Output Drive Wheels
Figure 14
Output Drive Wheel Assembly

An Output Drive Wheel Assembly is provided in the Wrap Section (See Figure 14). These
wheels assist in controlling the mailpiece when the Wrap Section is gapped.

Figure 15
Button Head Screw

Brass Tip Set Screw
The Output Drive Wheel Assembly may be located on the Operator’s Side or Non-Operator’s
Side. To relocate the Assembly remove Button Head Screw, loosen Brass Tip Set Screw (See
Figure 15) and slide assembly to opposite side. Using the other slot provided, replace the Button
Head Screw and secure the Brass Tip Set Screw.

MCSPRO-1020 Tabbing System User’s Guide

Note: The Output Drive Wheel Assembly position may be adjusted within the slots to avoid ink
tracking.
Warning: For pass thru operation (Not applying tabs), set up as described above. Product
conveyed by tabber transport belts only, and not controlled by top drive, can skew and migrate
into the gearbelts of the upper wrap section. Severe damage or breakage can occur! When the
tabber base is left in-line and used as a conveyor, the same set up procedures for tabbing,
labeling or stamp affixing must be used. However, since securing tabs, labels or stamps to the
product is not a requirement, the gap setting (See Section 5.1.5) may be opened slightly more
than normal for product flow.

4.1.11 Center Belt Adjustment
Figure 16

Center Transport Belt

Adjuster Knobs

Requirement: Adjust Center Belt position to support Product Edge.
Note: Transport Base must be powered up to move center belt..
Procedure:
1.
2.
3.
4.

Power up Base and operate with Speed Control.
Loosen Adjuster Knobs shown in Figure 16.
Gently push Adjuster along it’s slot to position Center Belt as required.
Secure Knobs to maintain belt position.

MCSPRO-1020 Tabbing System User’s Guide

4.1.12 Position Upper Press Rolls
The upper press rolls, located at the input of the wrap section, may be positioned across their
drive shaft to secure tabs for wrap tabbing, labeling or stamp application on the product.
Rolls are provided to meet the requirements, and are designed to move by hand. Two press rolls
are provided for systems using the standard 2” head, and four rolls are supplied on the 4” wide
head systems.
Requirement: Position upper press rolls for wrap tabbing.
Procedure:
1.
2.
3.

Loosen wrap section lock knobs and raise pivoting portion of wrap section (Figure 17).
Push press roll (1) for operator side or (4) non-operator side (Figure 18), to the outermost
position.
Release safty lock pin. Return wrap section to operating position and secure lock knobs.
Lock knobs must be secured during operation.

Note:
For labeling or stamp affixing requirements, press rolls (1) through (4) may be positioned in
various configurations in front of the peel point to meet size
requirements.

Figure 17

MCSPRO-1020 Tabbing System User’s Guide

Figure 18

4.1.13 Idler Wheel Adjustments
Requirement:
Idler wheel assemblies must be positioned and adjusted correctly to assure tab wrap performance
and avoid damage to wrap guide.
Note: Lexan cover has been removed for clarity. It is not necessary to remove for the following
procedure.
Procedure:
1.
2.
3.
4.

Raise upper wrap section to lock position.
Position block assembly (operator’s side shown) with screw head and spacer against inner
frame of upper wrap section. See Figure 19.
Rotate block wheel assembly on the fixed mounting shaft, causing outward pressure on
the belt. See Figure 20.
Lightly secure brass tip set screw. See Figure 19.

MCSPRO-1020 Tabbing System User’s Guide

Figure 19

Figure 20

Inner Frame

Brass Tip Set Screw
Pressure on Belt

Screw Head & Spacer
5.
6.

Lower wrap section to operating position and secure with swing bolts and knobs.
Turn product thickness adjust counterclockwise to zero stop position (See Figure 21).
Figure 22

Figure 21

Swing Bolt & Knob
Product Thickness Adjust

Block Resting on Screw Head

Note: Idler wheel mounting block should be resting firmly on the wrap guide mounting screw
head (Figure 22). The block and wheels must straddle the wrap guide right angle, as shown with
clearance on each side.
7.
8.

Raise upper wrap section to lock position. Secure brass tip set screw. See Figure 19.
Repeat all procedures above for non-operator’s side.

Note: The idler wheel assembly is now adjusted to its correct position and will give tight wrap on
all product when the upper wrap assembly is correctly gapped (See Section 4.1.6 Set Gap).

MCSPRO-1020 Tabbing System User’s Guide

4.2 Head Set-up
The head will be set up differently for different size labels. If the tabs/ labels have a backer width
of less than 2 inches, then the head should be set up with the Tab Sensor Assembly and the two
“thin” Inner Spool Guides. Labels with a backer width over 2 inches must be set up with the
Label Sensor Assembly and the two “wide label” Inner Spool Guides.
The tabbing head utilizes optical sensors to ensure accurate tab/label position. It is important for
the tab/ labels to be positioned so their centers run under the optical sensor. When using the label
sensor the label threading path is centered on the center of the label guide idlers. When using the
Tab Sensor the threading path is centered about 1-3/4” off the main side frame of the head.

4.2.1 Install Inner Spool Guides
Choose the appropriate spool guides for the tabs/ labels to be run. The exact location of the spool
guides depends on the width of the tabs/ labels being run. Keep in mind that it is important for
the tabs/labels to be centered on the optical path of the tab/ label sensor. Select the appropriate
locating slot on the spool support shaft and engage the locating latch of the guide. The center
location is marked on the tab / label sensor and it defines the center for the full threading path.
4.2.2 Secure Source Spool
Slip your roll of tabs over the supporting hub of the inner spool support. Push the outer spool
support against the side of the source spool, secure with the spool knob. The knob should be tight
enough to ensure that the tab/label roll cannot slip on the hub of the inner spool support.
4.2.3 Threading
Adjust the tab/label guides on the idlers for the width of the labels to be used. Gap the springloaded idlers in both the roll unwind and tab drive sections. Thread according to the figure
provided on the main side frame. Note that the unpeeled tabs slide through the tab sensor while
the path of the waste liner is under the bottom sensor plate. The Bin Sensor must be located to
sense the tab/label liner for proper uwinding.

4.2.4 Secure Waste Take-up Spool
Slip an empty tab/label core over the supporting hub of the inner spool support. Secure the
threaded end of the liner to the empty core with tape or a label. Push the outer spool support
against the side of the core and secure with the spool knob. The knob should be tight enough to
MCSPRO-1020 Tabbing System User’s Guide

ensure that the take-up roll cannot slip on the hub of the inner spool support. The Take-up Full
Sensor must be located to sense the waste tab/label liner for overflow detection.

4.2.5 Adjust Tab Sensor
The tabber uses a pair of optical sensors housed in the tab sensor to register each tab. These
sensors are about ½ inch from the “peel point” and “look through” the labels and liner enabling
the detection of the tab/label edges. This sensing technique will ensure accurate detection when
tuned for the tabs currently being run. Adjustments are made automatically once the operator
initiates the tuning process. The adjustment is different for plain paper tabs versus clear plastic or
translucent tabs. For paper tabs make sure that only liner is present inside the tab sensor, back
feed liner or peel tabs to make this possible. For clear or translucent tabs make sure that the tabs
are still attached to the liner, and the lead edge of a liner registration marker must be at the peel
point edge.
Procedure
1) Power-up the head by turning on the Head Power Rocker Switch
2) Press the “SETUP” key to access the setup menu. “SETUP” should be displayed on the first
line of the display.
3) Press either the “” or “” until “ADJUST TAB SENSOR ?” is displayed on the second
line of the LCD.
4) When using typical paper tabs it is important to have the machine fully threaded, but with no
tab present in the tab sensor. It is important to make this setting while only liner is present in
the tab sensor. When using translucent or clear tabs it is important to have the machine fully
threaded with a tab present in the tab sensor. It is important not to have a liner registration
mark directly under the sensor while making the adjustment. Since the optical path of the tab
sensor is approximately ½” from the peel point edge, adjusting the sensor after aligning a
registration mark with the peel point edge will assure that proper setting will be found.
5) The controller will automatically make the optimal sensor adjustment when the “ENTER”
key is pressed. The LCD will indicate completion by displaying “TAB SENSOR
ADJUSTED”.
“SETTING = xxx% “
The xxx represents the electrical setting used for the sensor. This value should normally
range from 70% to 97% when setting with liner in the sensor. A value of 01% indicates sensor
disconnection or sensor failure. A value between 01% and 70% probably indicates that the tab
sensor requires cleaning. A value of 100% should always be obtained when adjusted with no
liner present. A value of less than 100% with no liner would indicate a dirty sensor. The sensor
should be adjusted without liner only as a diagnostic tool. The sensor must be readjusted with
liner before normal operation.

4.2.6 Adjust Pitch Setting
The distance between the lead edges of two consecutive tabs still attached to release liner defines
the Tab Pitch. This is an important value since it defines how far the tab drive will move when it
applies tabs. The minimum pitch is 0.75” and the maximum pitch is 7.00”.
Note: Since it is difficult for the system to reverse itself, it is always better to enter a lower
number for pitch versus a larger number. The system can “self-correct” for any slightly
undersized pitch whereas a system with an oversized pitch may never be able to synchronize the
tab position. It short, an oversized pitch means bad tab/label placement.
Procedure

MCSPRO-1020 Tabbing System User’s Guide

1) Take the system offline.
2) Press the “SETUP” key to access the setup menu. “SETUP” should be displayed on the first
line of the display.
3) Press either the “” or “” until “PITCH: x.xx >_” is displayed on the second line of the
display. The x.xx represents the current setting for tab pitch.
4) To increase the Tab Pitch, press the “+” key until the desired location is displayed as the
current setting. To decrease the Tab Pitch, press the “-“ key until the desired location is
displayed as the current setting.
-Or5) The desired pitch can be directly entered from the numeric keypad.
6) As the new setting is entered it appears to the right of the current setting.
7) Once entry of the new value is completed press the “ENTER” key to save the new value. The
LCD will indicate completion by replacing the current setting with the new setting.

4.2.7 Select Product Sensor
Through beam type opto-electronic sensors are used to detect the presence of product to
be tabbed/ labeled. Since the tabbing takes place at either the front or rear of the unit, product
sensors are located at both the front and rear. The operator can select the appropriate product
sensor to be active.
Procedure
1) Take the system offline.
2) Press the “SETUP” key to access the setup menu. “SETUP” should be displayed on the first
line of the display.
3) Press either the “” or “” until “PRODUCT SENSOR: (RIGHT)FRONT or
(LEFT)REAR” is displayed on the second line of the LCD. The xxxxxx represent the current
count.
4) Press the “+” key to change from (RIGHT)FRONT to (LEFT)REAR. Press the “-“ key to
change from REAR to FRONT. The LCD will update sensor selection as it is made.

Tab/ Label Position Overview
The location and number of tabs/labels to be applied to a single product is controlled by
the choices accessed by the “POSITION” key. The “POSITION” key is active only when the
unit is offline. The position setting to be displayed and or adjusted is controlled by the “” key
and or “” key. After displaying the setting of interest it can then be adjusted by one of two
methods: direct keypad entry or incremental adjustment. The direct keypad entry is accomplished
by using the numeric keypad to directly enter the desired position. After the position has been
entered the “ENTER” key must be pressed to load the new value into memory. Incremental
adjustments are made by using the “+” and or “-“ keys. The current value will be increased by
0.05” every time the “+” key is pressed. The current value will be decreased by 0.05” every time
the “-” key is pressed. The maximum number of tabs that can be applied in a single pass is three.
The minimum position is 00.00” and the maximum position is 20.00”.

4.2.8 Tab/ Label Position Entry

MCSPRO-1020 Tabbing System User’s Guide

The distance between the product lead edge and the lead edge of the tab/ label defines the tab/
label positions. The system uses position units measured in inches with a precision on 1/100 of
an inch. The three tab positions are defined by their order of application. If only one tab is
being applied to a product, then Tab Position # 1 defines its location. If two tabs are applied, then
Tab Position # 1 defines the leading edge tab and Tab Position # 2 defines the trailing edge tab.
If three tabs are applied, then Tab Position # 1 defines the leading edge tab; Tab Position # 3, and
the middle tab is defined by Tab Position #2 define the trailing edge tab. When using more than
one tab the second or third tab position must have a value greater than the (previous tab position
value + Tab Pitch)
TRAILING EDGE

LEADING EDGE

Product Flow

Tab Position 1
Tab Position 2
Tab Position 3

Procedure
1) Take the system offline.
2) Press the “POSITION” key to access the test menu. “POSITION” should be displayed on the
first line of the display.
3) Press either the “” or “” until “TAB POS x: yy.yy>_” is displayed on the second line of
the display. The x represents the tab position of interest and the yy.yy represents the current
setting for that tab position.
4) To increase the Tab Position from the leading edge press the “+” until the desired location is
displayed as the current setting. To decrease the Tab Position from the leading edge press the
“-“ until the desired location is displayed as the current setting.
-Or5) The desired position can be directly entered from the numeric keypad.
6) As the new setting is entered it appears to the right of the current setting.
7) Once entry of the new value is completed press the “ENTER” key to save the new value. The
LCD will indicate completion by replacing the current setting with the new setting.
4.2.9 Number of Tabs
The unit can apply 1 to 3 tabs on a single product in one pass. The “POSITION” key
gives access to this setting.
Procedure
MCSPRO-1020 Tabbing System User’s Guide

1) Take the system offline.
2) Press the “POSITION” key to access the position menu. “POSITION” should be displayed
on the first line of the display.
3) Press either the “” or “” until “NUMBER OF TABS: x” is displayed on the second line
of the display. The x represents the current setting for the number of tabs to be applied to a
given product.
4) To increase the Number of Tabs to be applied, press the “+” key until the desired number is
displayed as the current setting. To decrease the Number of Tabs to be applied, press the “-“
key until the desired number is displayed as the current setting.
4.2.10 Begin Tabbing
The system should now be ready to apply tabs/labels. Turn the head online by pressing
the online key on the operator interface.

MCSPRO-1020 Tabbing System User’s Guide

Chapter 5 - Controller Programming/Diagnostics
5.1 Setup Programming
The operator can adjust many of the components and parameters necessary to setup the unit,
through the operator interface. The “SETUP” key is used to access these adjustments and is active
only when the unit is offline. The setup parameter to be displayed and or adjusted is controlled by
the “” key and or “” key. The components/ parameters that can be adjusted are listed below:
•
•
•
•
•
•
•

Tab Pitch
Job Memory
Auto Tab Calculator Product Size
Product/ Tab Sensor Offset
Tab Sensor Sensitivity
Counter Reset
Product Sensor Selection

5.1.1 Pitch Setting
The distance between the lead edges of two consecutive tabs still attached to release liner defines
the Tab Pitch. This is an important value since it defines how far the tab drive will move when it
applies tabs. The minimum pitch is 0.75” and the maximum pitch is 7.00”.

Procedure
1) Take the system offline.
2) Press the “SETUP” key to access the setup menu. “SETUP” should be displayed on the
first line of the display.
3) Press either the “” or “” until “PITCH: x.xx >_” is displayed on the second line of
the display. The x.xx represents the current setting for tab pitch.
4) To increase the Tab Pitch, press the “+” key until the desired location is displayed as the
current setting. To decrease the Tab Pitch, press the “-“ key until the desired location is
displayed as the current setting.
-Or5) The desired pitch can be directly entered from the numeric keypad.
6) As the new setting is entered it appears to the right of the current setting.
7) Once entry of the new value is completed press the “ENTER” key to save the new value.
The LCD will indicate completion by replacing the current setting with the new setting.

5.1.2 Save Setup to Memory
Two memory locations are reserved for saving the most frequent job settings. Memory location 1
can retain the Tab Pitch, Tab Position # 1, Tab Position # 2, Tab Position # 3, Number of Tabs,
and Product Sensor Selection settings. Memory location 2 can retain the Tab Pitch, Tab Position
# 1, Tab Position # 2, Number of Tabs, and Product Sensor Selection settings.
Procedure
MCSPRO-1020 Tabbing System User’s Guide

1) Take the system offline.
2) Press the “SETUP” key to access the setup menu. “SETUP” should be displayed on the first
line of the display.
3) Press either the “” or “” until “SAVE(M1 or M2) >_” is displayed on the second line of
the display.
4) To save the current settings enter either “1” or “2” from the numeric keypad, then press the
“ENTER” key.
5) The LCD will display the message “Mx SAVED”. The x represents the number of the
memory location selected by the operator.

5.1.3 Auto Tab Calculator Product Size
The controller can calculate the proper location(s) for tabs on any given mail piece. The
operator must enter the size of the mail piece (product), the number of tabs to be applied, and the
tab pitch. The system can then calculate and program the appropriate tab positions. The
minimum product size is 05.00” and the maximum is 20.00”.
Procedure
1) Take the system offline.
2) Press the “SETUP” key to access the setup menu. “SETUP” should be displayed on the first
line of the display.
3) Press either the “” or “” until “AUTO: xx.xx >_” is displayed on the second line of the
LCD. The xx.xx represents the current product size to be used by the calculator.
4) Increase the product size by pressing the “+” key until the desired size is displayed as the
current setting. Decrease the product size by pressing the “-“ key until the desired size is
displayed as the current setting.
-Or5) The desired size can be directly entered from the numeric keypad. As the new setting is
entered it appears to the right of the current setting.
6) Once entry of the new value is completed press the “ENTER” key to calculate the new
position values. The LCD will indicate completion by displaying the newly calculated
positions “TAB 1 TAB 2 TAB 3”
xx.xx yy.yy zz.zz

5.1.4 Product/ Tab Sensor Offset

The controller must know the distance between the product sensor and tab sensor (peel point) in
order to accurately place tabs at the desired location. When the operator makes small mechanical
adjustments of the tab sensor location, the distance between the product and tab sensors will also
be changed. This programmed offset must be kept up to date with sensor movements, in order to
obtain the highest positional accuracy. Although the minimum offset is 2.00” and the maximum
is 9.00”, only small changes to the default offset should be needed.

Procedure
1) Take the system offline.
MCSPRO-1020 Tabbing System User’s Guide

2) Press the “SETUP” key to access the setup menu. “SETUP” should be displayed on the first
line of the display.
3) Press either the “” or “” until “SENSOR: x.xx >_” is displayed on the second line of the
LCD. The x.xx represents the current setting for sensor offset.
4) To increase the Sensor Offset, press the “+” key until the desired value is displayed as the
current setting. To decrease the Sensor Offset, press the “-“ key until the desired value is
displayed as the current setting.
-Or5) The desired offset can be directly entered from the numeric keypad.
6) As the new setting is entered it appears to the right of the current setting.
7) Once entry of the new value is completed press the “ENTER” key to save the new value. The
LCD will indicate completion by replacing the current setting with the new setting.

5.3.5 Tab Sensor Sensitivity
The controller must know the location of each tab edge in order to place the tab
accurately on product. Through beam type opto-electronic sensors are used to “look through” the
liner and tabs. The electronics can detect a significant contrast between just liner (found between
tabs) and the combination of tabs on top of the release liner. Since this accurate detection is so
important, setting the correct setting has been made very simple. This adjustment should be made
periodically since dust and debris can block the optical path, thus affecting operation. It is also
important to make the adjustment whenever setting up for a different type/ manufacturer of tab.
Procedure
1) Take the system offline.
2) Press the “SETUP” key to access the setup menu. “SETUP” should be displayed on the
first line of the display.
3) Press either the “” or “” until “ADJUST TAB SENSOR ?” is displayed on the
second line of the LCD.
4) When using typical paper tabs it is important to have the machine fully threaded, but with
no tab present in the tab sensor. It is important to make this setting while only liner is
present in the tab sensor. When using translucent or clear tabs it is important to have the
machine fully threaded with a tab present in the tab sensor. It is important not to have a
liner registration mark directly under the sensor while making the adjustment. Since the
optical path of the tab sensor is approximately ½” from the peel point edge, adjusting the
sensor after aligning a registration mark with the peel point edge will assure that proper
setting will be found.
5) The controller will automatically make the optimal sensor adjustment when the
“ENTER” key is pressed. The LCD will indicate completion by displaying :
“TAB SENSOR ADJUSTED”.
“SETTING = xxx% “
The xxx represents the electrical setting used for the sensor. This value should normally
range from 70% to 97% when setting with liner in the sensor. A value of 01% indicates sensor
disconnection or sensor failure. A value between 01% and 70% probably indicates that the tab
sensor requires cleaning. A value of 100% should always be obtained when adjusted with no
liner present. A value of less than 100% with no liner would indicate a dirty sensor. The sensor
should be adjusted without liner only as a diagnostic tool. The sensor must be readjusted with
liner before normal operation.
5.3.6 Counter Reset
The controller displays and records a product count. The operator can reset this count to
zero at any time. The current count is retained in memory at power down and recalled at power
up.
MCSPRO-1020 Tabbing System User’s Guide

5.3.7 Product Sensor Selection
Through beam type opto-electronic sensors are used to detect the presence of product to
be tabbed/ labeled. Since the tabbing takes place at either the front or rear of the unit, product
sensors are located at both the front and rear. The operator can select the appropriate product
sensor to be active.
Procedure
1) Take the system offline.
2) Press the “SETUP” key to access the setup menu. “SETUP” should be displayed on the
first line of the display.
3) Press either the “” or “” until “PRODUCT SENSOR: (RIGHT)FRONT or
(LEFT)REAR” is displayed on the second line of the LCD. The xxxxxx represent the
current count.
4) Press the “+” key to change from (RIGHT)FRONT to (LEFT)REAR. Press the “-“ key
to change from REAR to FRONT. The LCD will update sensor selection as it is made.

5.2 Position Programming
The location and number of tabs/labels to be applied to a single product is controlled by
the choices accessed by the “POSITION” key. The “POSITION” key is active only when the
unit is offline. The position setting to be displayed and or adjusted is controlled by the “” key
and or “” key. After displaying the setting of interest it can then be adjusted by one of two
methods: direct keypad entry or incremental adjustment. The direct keypad entry is accomplished
by using the numeric keypad to directly enter the desired position. After the position has been
entered the “ENTER” key must be pressed to load the new value into memory. Incremental
adjustments are made by using the “+” and or “-“ keys. The current value will be increased by
0.05” every time the “+” key is pressed. The current value will be decreased by 0.05” every time
the “-” key is pressed. The maximum number of tabs that can be applied in a single pass is three.
The minimum position is 00.00” and the maximum position is 20.00”.

5.2.1 Tab/ Label Position Entry
The distance between the product lead edge and the lead edge of the tab/ label defines the tab/
label positions. The system uses position units measured in inches with a precision on 1/100 of
an inch. The three tab positions are defined by their order of application. If only one tab is
being applied to a product, then Tab Position # 1 defines its location. If two tabs are applied, then
Tab Position # 1 defines the leading edge tab and Tab Position # 2 defines the trailing edge tab.
If three tabs are applied, then Tab Position # 1 defines the leading edge tab; Tab Position # 3
MCSPRO-1020 Tabbing System User’s Guide

defines the trailing edge tab, and the middle tab is defined by Tab Position #2. When using more
than one tab the second or third tab position must have a value greater than the (previous tab
position value + Tab Pitch).
TRAILING EDGE

LEADING EDGE

Product Flow

Tab Position 1
Tab Position 2
Tab Position 3

Procedure
1) Take the system offline.
2) Press the “POSITION” key to access the test menu. “POSITION” should be displayed
on the first line of the display.
3) Press either the “” or “” until “TAB POS x: yy.yy>_” is displayed on the second line
of the display. The x represents the tab position of interest and the yy.yy represents the
current setting for that tab position.
4) To increase the Tab Position from the leading edge press the “+” until the desired
location is displayed as the current setting. To decrease the Tab Position from the leading
edge press the “-“ until the desired location is displayed as the current setting.
-Or5) The desired position can be directly entered from the numeric keypad.
6) As the new setting is entered it appears to the right of the current setting.
7) Once entry of the new value is completed press the “ENTER” key to save the new value.
The LCD will indicate completion by replacing the current setting with the new setting.

5.2.2 Number of Tabs
The unit can apply 1 to 3 tabs on a single product in one pass. The “POSITION” key
gives access to this setting.

Procedure
1) Take the system offline.
MCSPRO-1020 Tabbing System User’s Guide

2) Press the “POSITION” key to access the position menu. “POSITION” should be
displayed on the first line of the display.
3) Press either the “” or “” until “NUMBER OF TABS: x” is displayed on the second
line of the display. The x represents the current setting for the number of tabs to be
applied to a given product.
4) To increase the Number of Tabs to be applied, press the “+” key until the desired number
is displayed as the current setting. To decrease the Number of Tabs to be applied, press
the “-“ key until the desired number is displayed as the current setting.

5.4 Head Diagnostics/ Test
The electrical control system of the unit is capable of testing 15 critical components. The
operator must select which test is to be performed from the operator interface. The unit must be
offline before any tests are run. The components/ parameters that can be tested are listed below:
•
•
•
•
•
•
•
•
•
•
•
•
•

Software Version
Tab Drive Cycle Test
Stop Relay Test
Motor / Brake Test (Take-up motor/ Unwind drive motor/ Source spool brake)
Base Cover Switch Test
Head Cover Switch Test
Bin Sensor Test
Take-up Sensor Test
Left Product Sensor Test
Right Product Sensor Test
Tab Sensor Test
Encoder Test
Factory Reset

5.4.1 Software Version
It is often important to know the version of the firmware that is running on a system. The
firmware version will often determine the capabilities of the unit. This test will simply display
the version number of firmware installed on the unit.
Procedure
1) Take the system offline.
2) Press the “TEST” key to access the test menu. “TEST” should be displayed on the first line
of the display.
MCSPRO-1020 Tabbing System User’s Guide

3) Press either the “” or “” until “VERSION X.X” is displayed on the second line of the
display. (X.X will be the version number of interest)

5.4.2 Tab Drive Cycle Test
The Tab Drive Cycle Test is used to test the function of the Tab Drive Motor. The Tab
Drive Motor is responsible for the accurate application of the tabs/labels.
Procedure
1) Take the system offline.
2) Remove any tabs/ labels from the head before conducting this test.
3) Press the “TEST” key to access the test menu. “TEST” should be displayed on the first line
of the display.
4) Press either the “” or “” until “TAB DRIVE CYCLE: OFF” is displayed on the second
line of the display.
5) Start the test by pressing the “ENTER” key.
6) While the test is being run the display should read “TAB DRIVE CYCLE: ON” and The Tab
Drive Wheel should alternate between 3 different states. The wheel should run forward at
high speed (2 second duration), then stop or rotate very slowly (2 second duration), then run
reverse at high speed (2 second duration), followed again by a stopped or very slow state.
The cycle will continue repeating until the “ENTER” key is used to stop the test.

5.4.3 Stop Relay Test
The Stop Relay allows the control system to shutdown the base whenever serious
problems have been detected. This test allows the operator to test the function of this relay.
Procedure
1) Take the system offline.
2) Press the “TEST” key to access the test menu. “TEST” should be displayed on the first line
of the display.
3) Press either the “” or “” until “STOP RELAY: OFF” is displayed on the second line of
the display.
4) Run the base by pressing the “START” button. The base should stop if the “ENTER” key is
pressed. After the “ENTER” key is pressed STOP RELAY: ON” will display on the second
line of the LCD.

5.4.4 Motor/ Brake Test
Three DC gearmotors are used to: 1) unwind the source spool, 2) brake the rotation of the
source spool, and 3) take-up the waste liner. The Motor/Brake Test allows the operator to test the
fitness of each of these gearmotors.
Procedure
1) Take the system offline.
2) Remove any tabs/ labels from the head before conducting this test.
3) Press the “TEST” key to access the test menu. “TEST” should be displayed on the first line
of the display.

MCSPRO-1020 Tabbing System User’s Guide

4) Press either the “” or “” until “MOTOR/ -BRAKE: OFF” is displayed on the second line
of the display.
5) Press the “ENTER” key to start the test. The second line of the LCD will display “MOTOR/
-BRAKE: ON”. While this test is being run the take-up motor should run continuously. The
unwind motor will run when the bin sensor is not blocked and stop when the bin sensor is
blocked. The source spool will brake when the bin sensor is blocked; the braking action is
released when the bin sensor is not blocked.

5.4.5 Base Cover Test
Note **** Due to a change intended to enhance the safety of the tabbing system, this test will
now give invalid results. Do not use this test to diagnose the condition of the magnetic switches
on the base cover.

5.4.6 Head Cover Test
A magnetic switch senses the condition of the head cover. This switch is used, as a
safety interlock that prevents the system from operating while the cover is open. The switch
condition is displayed while this test is being run.
Procedure
1) Take the system offline.
2) Press the “TEST” key to access the test menu. “TEST” should be displayed on the first line
of the display.
3) Press either the “” or “” until “HEAD COVER: OPEN” or “HEAD COVER: CLOSED”
is displayed on the second line of the display.
4) The LCD display will indicate the current state of the head cover while this test is being run.

5.4.7 Bin Sensor Test
A retro-reflective sensor is used to determine the state of the tab/label bin. The sensor is
used to ensure that some tabs/labels have been unwound from the source spool and are ready for
application. The bin condition is displayed while this test is being run.
Procedure
1) Take the system offline.
2) Press the “TEST” key to access the test menu. “TEST” should be displayed on the first line
of the display.
3) Press either the “” or “” until “BIN SENSOR: BLOCKED” or “BIN SENSOR:
UNBLOCKED” is displayed on the second line of the display.
MCSPRO-1020 Tabbing System User’s Guide

4) The LCD display will indicate the current state of the bin sensor while this test is being run.

5.4.8 Take-up Sensor Test
A reflective sensor is used to determine when the waste take-up spool is filled to
capacity. The sensor condition is displayed while this test is being run.
Procedure
1) Take the system offline.
2) Press the “TEST” key to access the test menu. “TEST” should be displayed on the first line
of the display.
3) Press either the “” or “” until “TAKE-UP : BLOCKED” or “TAKE-UP: UNBLOCKED”
is displayed on the second line of the display.
4) The LCD display will indicate the current state of the take-up sensor while this test is being
run.

5.4.9 Left Product Sensor Test
A “through beam” type opto-electronic sensor is used to sense the edge of the product
about to be tabbed/ labeled. The sensor condition is displayed while this test is being run.
Procedure
1) Take the system offline.
2) Press the “TEST” key to access the test menu. “TEST” should be displayed on the first line
of the display.
3) Press either the “” or “” until “LF PRODUCT: BLOCKED” or “LF PRODUCT:
UNBLOCKED” is displayed on the second line of the display.
4) The LCD display will indicate the current state of the left product sensor while this test is
being run.

5.4.10 Right Product Sensor Test
A “through beam” type opto-electronic sensor is used to sense the edge of the product
about to be tabbed/ labeled. The sensor condition is displayed while this test is being run.
Procedure
1) Take the system offline.
2) Press the “TEST” key to access the test menu. “TEST” should be displayed on the first line
of the display.
3) Press either the “” or “” until “RT PRODUCT: BLOCKED” or “RT PRODUCT:
UNBLOCKED” is displayed on the second line of the display.
4) The LCD display will indicate the current state of the right product sensor while this test is
being run.

MCSPRO-1020 Tabbing System User’s Guide

5.4.11 Tab/ Label Sensor Test
A “through beam” type opto-electronic sensor is used to sense the edge of the tab/ label
about to be dispensed. The sensor condition is displayed while this test is being run.
Procedure
1) Take the system offline.
2) Press the “TEST” key to access the test menu. “TEST” should be displayed on the first line
of the display.
3) Press either the “” or “” until “TAB SEN: BLOCKED” or “TAB SEN: UNBLOCKED”
is displayed on the second line of the display.
4) The LCD display will indicate the current state of the tab/label sensor while this test is being
run.

5.4.12 Encoder Test
An optical encoder is used to sense product speed and position information. The encoder
test displays a running pulsewheel count from the encoder.
Procedure
1) Take the system offline.
2) Press the “TEST” key to access the test menu. “TEST” should be displayed on the first line
of the display.
3) Press either the “” or “” until “ENCODER: 00000 is displayed on the second line of the
display.
4) The LCD will display a running count from the encoder. The count overflows to zero after
reaching a maximum count of 65,535. The encoder should register approximately 150 counts
for every inch of transport belt travel.

5.4.13 Factory Reset
The factory reset allows the operator to reset all operator programmable settings to their
original factory settings. This could be necessary if the system memory becomes corrupt.
Symptoms that may indicate the need for a factory reset include; tabs/ labels significantly and
repeatedly misplaced, or no tabs/ labels applied at all.
Procedure
1) Take the system offline.
2) Press the “TEST” key to access the test menu. “TEST” should be displayed on the first line
of the display.
3) Press either the “” or “” until “FACTORY RESET ?” is displayed on the second line of
the display.
4) Press the “ENTER” key to initiate the reset. Upon completion, the LCD will display
“FACTORY SETTINGS LOADED TO MEMORY”.

MCSPRO-1020 Tabbing System User’s Guide

Chapter 6 – Troubleshooting

MCSPRO-1020 Tabbing System User’s Guide

Chapter 7 – Appendix
FIGURE A1 – BASE CONTROL SYSTEM DIAGRAM

MCSPRO-1020 Tabbing System User’s Guide

FIGURE A2 – HEAD CONTROL SYSTEM DIAGRAM

MCSPRO-1020 Tabbing System User’s Guide

FIGURE A3 – HEAD SYSTEM DIAGRAM

MCSPRO-1020 Tabbing System User’s Guide

ILLUSTRATED PART BREAKDOWN
WASTE TAKE-UP SENSOR
P/N SE001400

TAB GUIDE, O-RING
P/N VG000100
TAB GUIDE, SPLIT RING
P/N PT002400

BIN SENSOR
P/N SE001200

TAB SENSOR ASSEMBLY
LABEL SENSOR ASSEMBLY

P/N SM002700 (2”)
P/N SM002701 (4”)

MCSPRO-1020 Tabbing System User’s Guide

KNOB, QUICK ACTING, ½ -13 P/N VK000600 (QTY 2)
UNWIND SPOOL ASS’Y, TABBER
UNWIND SPOOL ASS’Y, LABELER

P/N SM001800 (2“)
P/N SM001801 (4”)

UNWIND SPOOL SUPPORT ASS’Y

TAKE-UP SPOOL ASS’Y, TABBER
TAKE-UP SPOOL ASS’Y, LABELER

P/N SM001604

P/N SM001900 (2“)
P/N SM001901 (4”)
IDLER ASS’Y, UNWIND DRIVE, TABBER P/N SM002200 (2“)
IDLER ASS’Y, UNWIND DRIVE, LABELER P/N SM002201 (4”)

URETHANE ROLLER, FLOAT IDLER, TABBER (2“) P/N VR000200
URETHANE ROLLER, FLOAT IDLER, LABELER (4“) P/N SM008401

TAKE-UP SPOOL SUPPORT ASS’Y

P/N SM001102

URETHANE ROLLER, UNWIND DRIVE, TABBER P/N VR000300
URETHANE ROLLER, UNWIND DRIVE, LABELER P/N VR000301

FRONT HEAD GUARD (SHOWN OPEN) P/N SM000501

DRIVE ROLL, TABBER (GRIT WHEEL)
DRIVE ROLL, LABELER (GRIT WHEEL)
IDLER ASS’Y, TAB DRIVE
IDLER ASS’Y, LABEL DRIVE

P/N PM003500 (2“)
P/N PM003501 (4“)

P/N SM002100 (2“)
P/N SM002101 (4”)

MCSPRO-1020 Tabbing System User’s Guide

P/N VB000102

P/N VB000102
SHAFT, SPOOL ,TABBER
SHAFT, SPOOL, LABELER

SPUR GEAR, 40 TOOTH, ½” BORE

P/N PM010500

SPUR GEAR, 20 TOOTH, ¼” BORE

BEARING, ½” ROLLER

P/N PL011103 (2”)
P/N PL011101 (4”)

SPUR GEAR, 18 TOOTH, 3/8” BORE
P/N PM010400

P/N VB000102

P/N PM006300

SPUR GEAR, 36 TOOTH, ¼” BORE

SPUR GEAR, 30 TOOTH, 1/4” BORE

P/N PM006100

P/N PM006400

SPUR GEAR, 30 TOOTH, 1/2” BORE P/N PM006200
BEARING, 3/8” ROLLER P/N VB000101

P/N VM000301

P/N VM000202

P/N AM000102

P/N VM000301

WRAP GUIDE, NON-OP. SIDE

WRAP GUIDE, OP. SIDE

P/N PL017301

P/N PL017300

SPUR GEAR, 48 TOOTH, 32 PITCH

P/N VB001000
P/N SM009000
P/N VB001000

MCSPRO-1020 Tabbing System User’s Guide

P/N VT002500

BELT ROLL,OUTPUT P/N SM008701
BELT ROLL, INPUT P/N SM010900

P/N VT003400
P/N VT003402 (USED ON STANDARD BASE)
**** TRANSPORT BELTS, 2”W x 78”L P/N VT003403 ***
**** (USED ON EXTENDED BASE) *****************
P/N PM016300
SHAFT, LOWER PRESS ROLL P/N PL016600
P/N PM016200

SHAFT, INPUT ROLL

P/N PL016800

SHAFT, INPUT BELT GUIDE P/N PL017000

P/N VB001000

PULLEY, 18 TOOTH, 3/8”PITCH, ½” WIDE

P/N SM013200

P/N VB001000

PULLEY, 14 TOOTH, 3/8”PITCH, ½” WIDE P/N PM016001

P/N SM008701

SHAFT, OUTPUT BELT GUIDE P/N PL020100
SHAFT, LOWER FOLD WHEEL P/N PL016700
P/N PM016300

P/N VT003902
P/N VB001000

SHAFT, LOWER OUTPUT ROLL P/N PL017100

P/N VB001000

P/N SM013200

PULLEY, 20 TOOTH, 3/8”PITCH, ½” WIDE P/N SM013201
SHAFT, REVERSING P/N PL016901

MCSPRO-1020 Tabbing System User’s Guide

TABBER CONTROL BOARD
SE000110

BASE ENCODER ASSEMBLY
SM009000
MOTOR SPEED CONTROL
ME000400

24VDC POWER SUPPLY
VC014300

MCSPRO-1020 Tabbing System User’s Guide

PRODUCT SENSOR
VC001000

RED MUSHROOM
PUSHBUTTON SWITCH
VC014600

BLACK PUSHBUTTON SWITCH
VC014602

THERMAL CIRCUIT
BREAKER/SWITCH 10A
VC014701

GREEN PUSHBUTTON
SWITCH VC014601

THERMAL CIRCUIT
BREAKER/SWITCH 5A
VC014700

GEARBELT, URETHANE, ¾”w x 72 TOOTH
VT003600

TRANSPORT BELTS, 2”w x 46-1/2”L (SET OF 4)
VT003402

TRANSPORT BELTS, 2”w x 27”L (SET OF
4)

LOWER FOLDWHEEL, URETHANE COATED (2)
PM016200

LOWER PRESSWHEEL, URETHANE COATED
(4)

MCSPRO-1020 Tabbing System User’s Guide

PULLEY, 19 TOOTH, 3/8”PITCH,1/2” WIDE
BEARING, RADIAL BALL, 5/8” W/SNAP RING

P/N

PM016000

VB001000
P/N

SHAFT, UPPER OUTPUT

P/N

VB001000

PL017400

P/N

PM015600

PULLEY, 16 TOOTH, 3/8”PITCH, ¾” WIDE P/N PM015600
P/N
P/N

VT003600

VT003600
BEARING, ROLLER, 5/8” I.D. P/N
PULLEY, FOLD FLANGE

PULLEY, 20 TOOTH,1/5”PITCH

P/N

VB000104

SM012700

PM015501

P/N

SM012700
P/N

VB001000

P/N VB001004
P/N VB001000
P/N PL019100

SHAFT, UPPER FOLD WHEEL

P/N

PL017500

PL019100

P/N VT003300
P/N VB000102

PULLEY, 18 TOOTH,1/5”PITCH

P/N PM015502

PRESS ROLL, UPPER OP. SIDE

P/N SM012900

SHAFT, UPPER PRESS ROLL

BEARING, ROLLER, 1/2” I.D.
PRESS ROLL, UPPER NON-OP. SIDE

P/N

PL017700

MCSPRO-1020 Tabbing System User’s Guide

P/N VB000102
SM012901

MISCELANIOUS SPARE PARTS NOT LISTED ABOVE
TABBING HEAD

VC006200
VH001900
VH003300

HEAD POWER SUPPLY FUSE
EXTENSION SPRING, 0.25” OD x 1.75” L (UNWIND REAL)
EXTENSION SPRING, 0.25” OD x 1.5” L (TAKE UP)

TABBING BASE
SE000202

OPERATOR INTERFACE

SE007400
VC010900
SE000700
VC014001
VC013501
VC013500
VC014500
VC014501
VC006202
VC006203
VT003902
VG000500
VH008101
VH007701
VK000700
VK000800
VK001000
VK001200
VK001201
SM009300
SM009400
SM009401
VH003900
VC005100
VC005200

BASE MOTOR ASSEMBLY
POWER CORDSET
HEAD POWER CABLE
HEAD CONTROL CABLE
RELAY, 24V COIL
RELAY, 12V COIL
CONTACT BLOCK, NORMALLY OPEN
CONTACT BLOCK, NORMALLY CLOSED
FUSE, 1A TIME DELAY (24V SUPPLY)
FUSE, 8A FAST ACTING (BASE MOTOR)
GEARBELT, L, ½”w x 68 TOOTH, 3/8” PITCH
“O” RING, CLEAR URETHANE, 4-5/16” x 1/8”
EXTENSION SPRING, ½”OD x 1-1/2”L
COMPRESSION SPRING, .36”OD x 1-1/4”L
2-3/8” DIA. BLACK KNOB
THUMB KNOB w/ THRU HOLE, 1-1/4” DIA.
CRANK HANDLE, 2.5”L
ADJUSTABLE CLAMPING HANDLE, SHORT SHAFT
ADJUSTABLE CLAMPING HANDLE, LONG SHAFT
KNOB, HEAD POSITION FINE ADJUST
KNOB, TABLE POSITION FINE ADJUST
KNOB, RESGISTRATION WHEEL ANGLE ADJUST
COMPRESSION SPRING, .360”OD x .75”L
REED SWITCH
MAGNET

MCSPRO-1020 Tabbing System User’s Guide

AF000512 - TABBING HEAD, MCS 2"
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24

Part Number
SM002608
SM001605
SM001102
VK000600
SM001800
SM001900
SM000501
VK001100
VH004103
PP002000
VH000402
VH006800
PA000201
PP005000
PA000301
PA000401
PP004900
PA000600
PA000701
PA000801
VH003100
VC007500
VC003501
VH002801

Description
Head Sub Assembly, 2"
Support Assembly, Unwind Spool, MCS
Take-Up Spool Assembly, Outer V3
Knob, Quick Acting, 1/2-13
Unwind Spool Assembly, Inner
Take-Up Spool Assembly, Inner
Front Guard Assembly
Knob, Black w/ #10-32 Stud
Collar, Locking, SS, 1/2" ID
Connector Plate, Head
Screw, Button Head Socket, #10-32 x 3/8"
Washer, External Lock, #10
Cover, Rear Main Top
Cover, Rear Main Bottom
Rear Cover, End, Take-Up
Cover, Rear, End
Cover, Rear, Bottom/Front
Brake End Cover
Cover, Unwind Brake, Top
Cover, Unwind Brake, Bottom
Jack Screw, #4-40 x 3/16"
Connector, DB25 Male, Panel Mount, Crimp Type
Connector, CPC, 9 Pin, Receptacle
Screw, Button Head Socket, #4-40 x 5/16"

Quantity
1
1
1
2
1
1
1
1
2
1
25
25
1
1
1
1
1
1
1
1
2
1
1
4

AF000513 - LABELING HEAD, MCS 4"
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27

Part Number
SM002609
SM001605
SM001102
VK000600
SM001801
SM001901
SM000501
VK001100
VH004103
PP002000
VH000402
VH006800
PA000201
PP005000
PA000301
PA000401
PP004900
PA000600
PA000701
PA000801
VH003100
VC007500
VC003501
VH002801
SM001800
SM001900
SM007300

Description
Head Sub Assembly, 4"
Support Assembly, Unwind Spool, MCS
Take-Up Spool Assembly, Outer V3
Knob, Quick Acting, 1/2-13
Unwind Spool Assembly, Inner, Labeler
Take-Up Spool Assembly, Inner, Labeler
Front Guard Assembly
Knob, Black w/ #10-32 Stud
Collar, Locking, SS, 1/2" ID
Connector Plate, Head
Screw, Button Head Socket, #10-32 x 3/8"
Washer, External Lock, #10
Cover, Rear Main Top
Cover, Rear Main Bottom
Rear Cover, End, Take-Up
Cover, Rear, End
Cover, Rear, Bottom/Front
Brake End Cover
Cover, Unwind Brake, Top
Cover, Unwind Brake, Bottom
Jack Screw, #4-40 x 3/16"
Connector, DB25 Male, Panel Mount, Crimp Type
Connector, CPC, 9 Pin, Receptacle
Screw, Button Head Socket, #4-40 x 5/16"
Unwind Spool Assembly, Inner
Take-Up Spool Assembly, Inner
Sensor Arm Assembly, Tabber 2"

Quantity
1
1
1
2
1
1
1
1
2
1
25
25
1
1
1
1
1
1
1
1
2
1
1
4
1
1
1

SM000501 - FRONT GUARD ASSEMBLY, V3
Item
1
2
3
4

Part Number
VZ001803
VC005200
VH002802
VH002403

Description
Guard, Front
Magnet
Screw, Button Head Socket, #4-40 x 1/2"
Nut, Hex, #4-40

Quantity
1
1
2
2

SM001102 - TAKE-UP SPOOL ASSEMBLY, OUTER V3
Item
1
2
3

Part Number
Description
PM004003 Hub, Outer Spool Support
PF016700 Plate, Outer Take-Up Spool Support
VH000901 Screw, Flat Head Socket, #6-32 x 5/16"

Quantity
1
1
2

SM001300 - TAKE-UP SENSOR ASSEMBLY
Item
1
2
3
4
5
6

Part Number
SE001400
PL001500
VH002801
PL001400
VH002905
VH002202

Description
Harness, Take-up Sensor
Mount, Take-up Sensor
Screw, Button Head Socket, #4-40 x 5/16"
Bracket, Take-up Sensor
Washer, Internal Lock, #6
Screw, Button Head Socket, #6-32 x 3/8"

Quantity
1
2
2
1
2
2

SM001301 - TAKE-UP SENSOR ASSEMBLY, LABELER
Item
1
2
3
4
5
6
7
8

Part Number
SE001400
PL001500
VH002801
PL001401
VH002905
VH002202
PF001100
VH001801

Description
Harness, Take-up Sensor
Mount, Take-up Sensor
Screw, Button Head Socket, #4-40 x 5/16"
Bracket, Take-up Sensor, Labeler
Washer, Internal Lock, #6
Screw, Button Head Socket, #6-32 x 3/8"
Cover, Take-Up Sensor
Washer, Nylon, .150" ID x .317" OD x .031" Thick

Quantity
1
2
2
1
2
2
1
2

SM001400 - HEAD INTERLOCK ASSEMBLY
Item
1
2
3
4
5
6

Part Number
VC005100
VH002801
SE001300
VC004601
VH002101
PL001600

Description
Reed Switch, SPST
Screw, Button Head Socket, #4-40 x 5/16"
Harness, Head Interlock
Clamp, Cable, 1/8", Nylon
Screw, Button Head Socket, #8-32 x 1/4"
Plate, Interlock

Quantity
1
2
1
2
2
1

SM001401 - HEAD INTERLOCK ASSEMBLY, LABELER
Item
1
2
3
4
5
6

Part Number
VC005100
VH002801
SE001300
VC004601
VH002101
PL001601

Description
Reed Switch, SPST
Screw, Button Head Socket, #4-40 x 5/16"
Harness, Head Interlock
Clamp, Cable, 1/8", Nylon
Screw, Button Head Socket, #8-32 x 1/4"
Plate, Interlock, Labeler

Quantity
1
2
1
2
2
1

SM001605 - SUPPORT ASSEMBLY, UNWIND SPOOL, MCS
Item
1
2
3
4

Part Number
PM004003
PF016600
VH000901
VD002500

Description
Hub, Outer Spool Support
Plate, Outer Source Spool Support
Screw, Flat Head Socket, #6-32 x 5/16"
Decal, MCS Pro Tabber

Quantity
1
1
2
2

SM001800 - UNWIND SPOOL ASSEMBLY, INNER
Item
1
2
3
4
5
6
7
8
9

Part Number
PM006500
VZ002100
VH000901
VH000903
VH000905
PF002400
VH003700
VH001801
VH003803

Description
Hub, Inner Spool Support
Plate, Inner Source Spool Support
Screw, Flat Head Socket, #6-32 x 5/16"
Screw, Flat Head Socket, #6-32 x 1/2"
Screw, Flat Head Socket, #6-32 x 7/8"
Latch, Spool
Ball-Nose Plunger, 1/4-20 x 5/8", 1/8" Ball
Washer, Nylon, .156" ID x .317" OD x .031" Thick
Nut, Hex, Self-Locking, #6-32

Quantity
1
1
3
1
1
1
1
2
2

SM001801 - UNWIND SPOOL ASSEMBLY, INNER, LABELER
Item
1
2
3
4
5
6
7
8
9

Part Number
PM006501
VZ002100
VH000901
VH000903
VH000905
PF002400
VH003700
VH001801
VH003803

Description
Hub, Inner Spool Support, Labeler
Plate, Inner Source Spool Support
Screw, Flat Head Socket, #6-32 x 5/16"
Screw, Flat Head Socket, #6-32 x 1/2"
Screw, Flat Head Socket, #6-32 x 7/8"
Latch, Spool
Ball-Nose Plunger, 1/4-20 x 5/8", 1/8" Ball
Washer, Nylon, .156" ID x .317" OD x .031" Thick
Nut, Hex, Self-Locking, #6-32

Quantity
1
1
3
1
1
1
1
2
2

SM001900 - TAKE-UP SPOOL ASSEMBLY, INNER
Item
1
2
3
4
5
6
7
8
9

Part Number
PM006500
VZ002000
VH000901
VH000903
VH000905
PF002400
VH003700
VH001801
VH003803

Description
Hub, Inner Spool Support
Plate, Inner Take-Up Spool Support
Screw, Flat Head Socket, #6-32 x 5/16"
Screw, Flat Head Socket, #6-32 x 1/2"
Screw, Flat Head Socket, #6-32 x 7/8"
Latch, Spool
Ball-Nose Plunger, 1/4-20 x 5/8", 1/8" Ball
Washer, Nylon, .156" ID x .317" OD x .031" Thick
Nut, Hex, Self-Locking, #6-32

Quantity
1
1
3
1
1
1
1
2
2

SM001901 - TAKE-UP SPOOL ASSEMBLY, INNER, LABELER
Item
1
2
3
4
5
6
7
8
9

Part Number
PM006501
VZ002000
VH000901
VH000903
VH000905
PF002400
VH003700
VH001801
VH003803

Description
Hub, Inner Spool Support, Labeler
Plate, Inner Take-Up Spool Support
Screw, Flat Head Socket, #6-32 x 5/16"
Screw, Flat Head Socket, #6-32 x 1/2"
Screw, Flat Head Socket, #6-32 x 7/8"
Latch, Spool
Ball-Nose Plunger, 1/4-20 x 5/8", 1/8" Ball
Washer, Nylon, .156" ID x .317" OD x .031" Thick
Nut, Hex, Self-Locking, #6-32

Quantity
1
1
3
1
1
1
1
2
2

SM002100 - IDLER ASSEMBLY, TAB DRIVE, V2
Item
1
2
3
4
5
6
7
8
9
10
11

Part Number
VR000200
PL003300
SM008100
PL003600
PL003500
VH000902
VH006001
VH003900
VH000701
PF003300
PF002500

Description
Roller, Float Idler
U Channel, Yoke, Tabber
Plate Assembly, Yoke Side, Tabber
Pin, Yoke Lock, Tabber
Knob, Yoke Lock
Screw, Flat Head Socket, #6-32 x 3/8"
Retaining Ring, External, 1/4
Spring, Compression, .360" OD x .625" L x .026" Dia. MW
Screw, Pan Head Phillips, #6-32 x 1/4"
Lug, Spring Retaining
Plate, Deflector, Tabber

Quantity
1
1
2
1
1
7
1
1
3
1
1

SM002101 - IDLER ASSEMBLY, LABEL DRIVE
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15

Part Number
SM008401
PL003301
SM008101
SM008102
PL003601
PL003500
VH000902
VH006001
VH003900
VH000701
PF003300
PF002501
PT003004
VH000506
VH001808

Description
Roller, Float Idler, Labeler
U Channel, Yoke, Labeler
Plate Assembly, Left Yoke Side, Labeler
Plate Assembly, Right Yoke Side, Labeler
Pin, Yoke Lock, Labeler
Knob, Yoke Lock
Screw, Flat Head Socket, #6-32 x 3/8"
Retaining Ring, External, 1/4
Spring, Compression, .360" OD x .625" L x .026" Dia. MW
Screw, Pan Head Phillips, #6-32 x 1/4"
Lug, Spring Retaining
Plate, Deflector, Label Drive
Shaft, Idler Support
Screw, Flat Head Socket, #10-32 x 1/2"
Washer, Nylon, .390" ID x .750" OD x .062" Thick

Quantity
1
1
1
1
1
1
7
1
1
4
2
1
1
2
2

SM002200 - IDLER ASSEMBLY, UNWIND DRIVE
Item
1
2
3
4
5
6
7
8
9
10

Part Number
VR000200
PL003300
SM008100
PL003600
PL003500
VH000902
VH006001
VH003900
VH000701
PF003301

Quantity
1
1
2
1
1
7
1
1
3
1

SM002201 - IDLER ASSEMBLY, UNWIND DRIVE, LABELER
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14

Part Number
SM008401
PL003301
SM008101
SM008102
PL003601
PL003500
VH000902
VH006001
VH003900
VH000701
PF003301
PT003004
VH000506
VH001808

Description
Roller, Float Idler, Labeler
U Channel, Yoke, Labeler
Plate Assembly, Left Yoke Side, Labeler
Plate Assembly, Right Yoke Side, Labeler
Pin, Yoke Lock, Labeler
Knob, Yoke Lock
Screw, Flat Head Socket, #6-32 x 3/8"
Retaining Ring, External, 1/4
Spring, Compression, .360" OD x .625" L x .026" Dia. MW
Screw, Pan Head Phillips, #6-32 x 1/4"
Lug, Spring Retaining, #6 x .687 Long
Shaft, Idler Support
Screw, Flat Head Socket, #10-32 x 1/2"
Washer, Nylon, .390" ID x .750" OD x .062" Thick

Quantity
1
1
1
1
1
1
7
1
1
4
2
1
2
2

SM002608 - HEAD SUB ASSEMBLY, 2"
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55

Part Number
VC004601
VM000301
PM003500
PL000200
VH000601
AM000103
VH003501
VH000102
VH001404
ME000201
VH000402
VH006800
VG000100
PT002400
PT001400
VH000303
PL000300
VH000202
PL000400
SM002100
SM002200
VH001808
PL000800
VH001900
VH003300
VH000702
VH002402
PL000902
PL003800
PA000900
VG000200
SM002700
PL006600
VH000204
VR000300
VH004102
PF002300
PA001200
VD000100
SE001200
PL001300
SM001300
SM001400
VH000405
PL011103
VH004103
PM006600
PM006700
VB000102
VB000101
VM000202
PM006100
PM006200
PM006300
PM006400

Description
Clamp, Cable, 1/8", Nylon
Gearmotor, 30.3VDC, 5.9:1
Grit Wheel, Modified
Washer, Drive Roll
Screw, Flat Head Socket, 1/4-20 x 5/8"
Servo Gearmotor, BLDC, Compumotor Collar Coupling, Copley Wiring
Screw, Cap Head Socket, M6 x 25mm
Washer, Internal Lock, 1/4
Washer, Flat, 1/4
Amplifier, BLDC Servo, Modified, Copley
Screw, Button Head Socket, #10-32 x 3/8"
Washer, External Lock, #10
O-Ring, 1-3/16 x 1-7/16 x 1/8
Guide, Split Ring
Idler, Roll
E-Ring, External, 3/8
Shaft, Idler, Peel Point
Screw, Cap Head Socket, 1/4-20 x 1/2"
Shaft, Idler
Idler Assembly, Tab Drive
Idler Assembly, Unwind Drive, V2
Washer, Nylon, .390" ID x .750" OD x .062" Thick
Shaft, Yoke
Spring, Extension, .250" OD x 1.750" L x .041" Dia. MW
Spring, Extension, .250" OD x 1.500" L x .041" Dia. MW
Screw, Pan Head Phillips, #6-32 x 3/4"
Nut, Hex, #6-32
Shaft, Pivot, Guard
Standoff, Guard
Bracket, Strain Relief
Bushing, Strain Relief
Tab Sensor Assembly
Support, Peel Point
Screw, Cap Head Socket, 1/4-20 x 1"
Roller, Unwind Drive
Collar, Locking, SS, 3/8" ID
Plate, Stripper
Bin
Tape, Reflective
Harness, Bin Sensor
Bracket, Bin Sensor
Take-Up Sensor Assembly
Head Interlock Assembly
Screw, Button Head Socket, #10-32 x 3/4"
Shaft, Hub Mount
Collar, Locking, SS, 1/2" ID
Plate, Unwind Brake Motor
Plate, Unwind Brive Motor
Bearing, Roller, 1/2" ID
Bearing, Roller, 3/8" ID
Gearmotor, 30.3VDC, 19.7:1
Spur Gear, 36 Tooth, 1/4 Bore, 24 Pitch, 1/4 Face
Spur Gear, 30 Tooth, 1/2 Bore, 24 Pitch, 1/4 Face
Spur Gear, 18 Tooth, 3/8 Bore, 24 Pitch, 1/4 Face
Spur Gear, 30 Tooth, 1/4 Bore, 24 Pitch, 1/4 Face

Quantity
1
2
1
1
5
1
4
24
23
1
14
18
12
12
6
13
1
21
5
1
1
5
2
1
1
2
2
1
1
1
1
1
1
3
1
1
1
1
1"
1
1
1
1
6
2
2
2
1
4
2
1
1
1
1
1

56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73

PM010400
PM010500
VH001601
VH001703
PT000100
VH000603
PL003000
PL003100
PL006701
SE001500
SE001600
SE001700
VC004600
VH002108
VC004602
VH002202
VH002905
VH007202

Spur Gear, Mod, 20 Tooth, 1/4 Bore, 24 Pitch, 1/4 Face
Spur Gear, Mod, 40 Tooth, 1/2 Bore, 24 Pitch, 1/4 Face
Key, Woodruff #6, 5/32 x 5/8
Screw, Set, Socket, Cup Point, #10-32 x 3/16"
Standoff, Motor Support
Screw, Flat Head Socket, 1/4-20 x 1"
Plate, Unwind
Plate, Take-Up
Plate, Main Frame, Head
Harness, Unwind Drive Motor
Harness, Unwind Brake Motor
Harness, Take-Up Motor
Clamp, Cable, 1/4", Nylon
Screw, Button Head Socket, #8-32 x 5/16"
Clamp, Cable, 3/16", Nylon
Screw, Button Head Socket, #6-32 x 3/8"
Washer, Internal Lock, #6
Screw, Hex Head, 1/4-20 x 1-1/4", Grade 5

1
1
2
9
12
12
1
1
1
1
1
1
1
2
2
2
2
1

SM002609 - HEAD SUB ASSEMBLY, 4"
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55

Part Number
VC004601
VM000301
PM003501
PL000200
VH000601
AM000103
VH003501
VH000102
VH001404
ME000201
VH000402
VH006800
VG000100
PT002400
PT001401
VH000303
PL000301
VH000202
PL000401
SM002101
SM002201
VH001808
PL000801
VH001900
VH003300
VH000702
VH002402
PL000903
PL003801
PA000900
VG000200
SM002701
PL006600
VH000204
VR000301
VH004102
SM007700
PA001201
VD000100
SE001200
PL001301
SM001301
SM001401
VH000405
PL011101
VH004103
PM006600
PM006700
VB000102
VB000101
VM000202
PM006100
PM006200
PM006300
PM006400

Description
Clamp, Cable, 1/8", Nylon
Gearmotor, 30.3VDC, 5.9:1
Grit Wheel, Modified, Labeler
Washer, Drive Roll
Screw, Flat Head Socket, 1/4-20 x 5/8"
Servo Gearmotor, BLDC, Compumotor Collar Coupling, Copley Wiring
Screw, Cap Head Socket, M6 x 25mm
Washer, Internal Lock, 1/4
Washer, Flat, 1/4
Amplifier, BLDC Servo, Modified, Copley
Screw, Button Head Socket, #10-32 x 3/8"
Washer, External Lock, #10
O-Ring, 1-3/16 x 1-7/16 x 1/8
Guide, Split Ring
Idler, Roll, Labeler
E-Ring, External, 3/8
Shaft, Idler, Peel Point, Labeler
Screw, Cap Head Socket, 1/4-20 x 1/2"
Shaft, Idler, Labeler
Idler Assembly, Label Drive
Idler Assembly, Unwind Drive, Labeler
Washer, Nylon, .390" ID x .750" OD x .062" Thick
Shaft, Yoke, Labeler
Spring, Extension, .250" OD x 1.750" L x .041" Dia. MW
Spring, Extension, .250" OD x 1.500" L x .041" Dia. MW
Screw, Pan Head Phillips, #6-32 x 3/4"
Nut, Hex, #6-32
Shaft, Pivot, Guard, Labeler, V3
Standoff, Guard, Labeler
Bracket, Strain Relief
Bushing, Strain Relief
Label Sensor Assembly, Labeler
Support, Peel Point
Screw, Cap Head Socket, 1/4-20 x 1"
Roller, Unwind Drive, Labeler
Collar, Locking, SS, 3/8" ID
Stripper Assembly, Labeler
Bin, Labeler
Tape, Reflective
Harness, Bin Sensor
Bracket, Bin Sensor, Labeler
Take-Up Sensor Assembly, Labeler
Head Interlock Assembly, Labeler
Screw, Button Head Socket, #10-32 x 3/4"
Shaft, Hub Mount, Labeler
Collar, Locking, SS, 1/2" ID
Plate, Unwind Brake Motor
Plate, Unwind Brive Motor
Bearing, Roller, 1/2" ID
Bearing, Roller, 3/8" ID
Gearmotor, 30.3VDC, 19.7:1
Spur Gear, 36 Tooth, 1/4 Bore, 24 Pitch, 1/4 Face
Spur Gear, 30 Tooth, 1/2 Bore, 24 Pitch, 1/4 Face
Spur Gear, 18 Tooth, 3/8 Bore, 24 Pitch, 1/4 Face
Spur Gear, 30 Tooth, 1/4 Bore, 24 Pitch, 1/4 Face

Quantity
1
2
1
1
5
1
4
24
23
1
14
18
12
12
6
13
1
21
5
1
1
5
2
1
1
2
2
1
1
1
1
1
1
3
1
1
1
1
6"
1
1
1
1
6
2
2
2
1
4
2
1
1
1
1
1

56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77

PM010400
PM010500
VH001601
VH001703
PT000100
VH000603
PL003000
PL003100
PL006701
SE001500
SE001600
SE001700
VC004600
VH002108
VC004602
VH002202
VH002905
VH007202
VH000701
VH002204
VH006200
VH006300

1
1
2
9
12
12
1
1
1
1
1
1
1
2
2
2
2
1
1
1
2
1

FO000900 - TABBING SYSTEM, MCS TABBER 2"
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24

Part Number
SM022604
AF000512
VC014001
SE000700
SE008000
VC010900
MD001000
VD002600
VH000402
VH006800
VS001600
VS001700
VS001900
VS000201
VS000300
VS000900
VS001000
VS001300
VS001400
VS001500
PW001800
VS000600
VD002300
VO000100

Description
Base Sub Assembly, MCS Tabber (2")
Tabbing Head, MCS 2"
Cable, Molded, DB25M-DB25F, 3 Feet
Cable, Head Power, External
Interlock Jumper Plug
Power Cord, 7'6", 18/3SVT, American, 125V, 10A, Black
Label, FCC Compliance
Decal, www.mcspro.com
Screw, Button Head Socket, #10-32 x 3/8"
Washer, External Lock, #10
Label Core, 1" Wide, 3" OD, 1/8" Wall
Label Core, 2" Wide, 3" OD, 1/8" Wall
Carton, Floor Tabber
Carton, Head, Triple Wall, 26 x 20-1/4 x 20-1/4
Foam, Shipping Box, 1 x 20 x 26, #2 PE Foam
Bubble Wrap, Anti-Static, 3/16 Thick
Bag, Clear Plastic, 3' x 5'
Carton, Head Unwind Insert
Carton, Head Take-Up Insert
Carton, Head Surround
Skid Strap, Tabber Weldment
Banding, 1/2 x .017
Tabs, 15/16" Dia. Paper, 5K Roll
Binder, White 1/2" Ring

USED BUT NOT SHOWN: ITEMS 11 - 24.

Quantity
1
1
1
1
1
1
1
1
2
2
2
2
1
1
2
8'
1
1
1
1
2
70'
1
1

FO000901 - LABELING SYSTEM, MCS TABBER 4"
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27

Part Number
SM022604
AF000513
VC014001
SE000700
SE008000
VC010900
MD001000
VD002600
VH000402
VH006800
PA006201
PL012400
VS001600
VS001700
VS001800
VS001900
VS000201
VS000300
VS000900
VS001000
VS001300
VS001400
VS001500
PW001800
VS000600
VD002300
VO000100

Description
Base Sub Assembly, MCS Tabber (2")
Labeling Head, MCS 4"
Cable, Molded, DB25M-DB25F, 3 Feet
Cable, Head Power, External
Interlock Jumper Plug
Power Cord, 7'6", 18/3SVT, American, 125V, 10A, Black
Label, FCC Compliance
Decal, www.mcspro.com
Screw, Button Head Socket, #10-32 x 3/8"
Washer, External Lock, #10
Label Tray
Tray Guide Tube
Label Core, 1" Wide, 3" OD, 1/8" Wall
Label Core, 2" Wide, 3" OD, 1/8" Wall
Label Core, 4" Wide, 3" OD, 1/8" Wall
Carton, Floor Tabber
Carton, Head, Triple Wall, 26 x 20-1/4 x 20-1/4
Foam, Shipping Box, 1 x 20 x 26, #2 PE Foam
Bubble Wrap, Anti-Static, 3/16 Thick
Bag, Clear Plastic, 3' x 5'
Carton, Head Unwind Insert
Carton, Head Take-Up Insert
Carton, Head Surround
Skid Strap, Tabber Weldment
Banding, 1/2 x .017
Tabs, 15/16" Dia. Paper, 5K Roll
Binder, White 1/2" Ring

USED BUT NOT SHOWN: ITEMS 13 - 27.

Quantity
1
1
1
1
1
1
1
1
4
2
1
1
2
2
2
1
1
2
8'
1
1
1
1
2
70'
1
1

SM010001 - UPPER FRAME ASSEMBLY
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55

Part Number
PA008200
SM010100
PF016000
PM012201
VB001101
VH007200
VH001404
VH002501
VT003000
VT002900
VT002800
SM012600
VH001702
PP001800
VH000207
PL017800
PL017600
PL018100
VH004403
VC004605
VH000106
VH002108
VC014000
VH007202
VH001812
VH000205
PL019600
SM009300
VH001810
VH003801
VH006102
PM010703
PT013401
VT004201
SM008901
SM008801
VH004103
PL015101
PL015300
PL015402
VH007303
VH002503
VH007302
PT010301
VT004202
PL015201
PF015800
VT002700
VB000611
VH006901
VH002405
VH001806
SM010700
SM010701
SM010800

Description
Base Frame, Top, Weldment
ACME Screw Support Assembly
Nut Plate, ACME Screw Support
Thrust Bearing Mount
Bearing, Thrust, 1/2" ID x 15/16" OD, 3 Piece
Screw, Hex Head, 1/4-20 x 3/4", Grade 5
Washer, Flat, 1/4
Washer, Split Lock, 1/4
Worm Gear, 12 Pitch, 20 Tooth, 14-1/2 Degree, Left Double Thread
Connecting Link, ANSI #35 Chain
Roller Chain, ANSI #35
Head Support, Weldment
Screw, Set, Socket, Cup Point, 1/4-20 x 1/4"
Head Mounting Plate, Motor Side
Screw, Cap Head Socket, 1/4-20 x 1-1/2"
Shaft, Ball Bushing, Head Mount Front and Lower Frame
Shaft, Head Mount, Rear, .625 #60 Case Rod
Tie Bar, Frame Mount
Collar, Split, Clamp, 3/4" ID
Clamp, Cable, 5/16", Nylon
Washer, Internal Lock, #8
Screw, Button Head Socket, #8-32 x 5/16"
Cable, Molded, DB25M-DB25M, 2 Meter
Screw, Hex Head, 1/4-20 x 1-1/4", Grade 5
Washer, Nylon, .500" ID x 1.000" OD x .062" Thick
Screw, Cap Head Socket, 1/4-20 x 3/4"
Head Adjustment Block
Knob, Head Position Fine Adjustment
Washer, Nylon, .195" ID x .437" OD x .031" Thick
Nut, Hex, Self Locking, #10-32
Spacer, Nylon, .187" ID x .375" OD x .375" Thick
Bar, Lift Assembly
Hex Support, ACME Nut
ACME Nut, 1/2-10, Single Start, Right Hand, Bronze, External Thread
ACME Screw, Worm Gear Assembly
ACME Screw, Head Lift Assembly
Collar, Locking, SS, 1/2" ID
Frame Support, Operator Side, Center
Head Support, Input
Frame Support, Output, Operator Side
Screw, Hex Head, 5/16-18 x 1-1/4", Grade 5
Washer, Split Lock, 5/16
Screw, Hex Head, 5/16-18 x 3", Grade 5
Spacer, Frame Mount
ACME Nut, 1/2-10, Standard Right Hand
Frame Support, Center, Non-Operator Side
Plate, Chain Tensioner
Sprocket, 10 Tooth, #35 Roller Chain
Bearing, Oil Impregnated Bronze, Plain, 3/8" ID x 1/2" OD x 3/4" L
Screw, Shoulder, Socket Head, 5/16-18 x 3/8" x 1"
Nut, Hex, 5/16-18
Washer, Nylon, .375" ID x .625" OD x .032" Thick
Worm Gear Support Assembly, Left Side
Worm Gear Support Assembly, Right Side
ACME Screw Support/Height Adjust Assembly

Quantity
1
3
4
4
4
24
2
26
1
1
104"
1
1
1
3
1
1
1
1
3
3
3
1
2
2
2
1
1
1
1
1
2
4
4
1
3
4
1
2
2
8
13
4
4
4
1
1
1
1
1
1
1
1
1
1

56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73

PL016500
VT003100
VH000403
VH006800
PL018900
VB000900
PL013000
VH000903
VK001200
PL021000
PL021100
VH000204
SM022800
SM022900
VH000205
SM022801
SM022901
PL015401

Shaft, Worm Gear
Worm, 12 Pitch, Left Double Thread
Screw, Button Head Socket, #10-32 x 1/2"
Washer, External Lock, #10
Tube, Head Mounting
Bearing, Linear, Ball Bushing, 3/4" ID
Head Mounting Plate, Operator Side
Screw, Flat Head Socket, #6-32 x 1/2"
Handle, Adjustable Clamping, 1/4-20 x .78"
Tie Bar, Frame Mount, Lower
Tie Bar, Lift
Screw, Cap Head Socket, 1/4-20 x 1"
Mount, Floating Wrap, Output, Operator Side
Mount, Floating Wrap, Center, Operator Side
Screw, Cap Head Socket, 1/4-20 x 3/4"
Mount, Floating Wrap, Output, Non-Operator Side
Mount, Floating Wrap, Center, Non-Operator Side
Frame Support, Output, Non-Operator Side

1
1
4
4
1
2
1
2
1
1
1
4
1
1
4
1
1
1

SM012002 - TRANSPORT ASSEMBLY
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55

Part Number
VB001000
SM008702
SM010900
PT018000
PL020700
PL020800
PL016800
PL016901
PL017000
PL020900
PM016200
VH001702
PM016300
PM016301
PM016700
PM016701
PM012902
PP004200
PF011503
VT003404
PF016103
VT004400
PW001700
VH000204
VH001404
VH000102
VH000602
VH000403
VH006800
VH000408
VH000502
PT013800
PL017300
PL017301
PL017203
PL017202
PP000300
PP000400
VG000304
SM013200
SM013201
VH008700
PL013900
VH002404
VT002500
SM009000
VT003903
PL019300
PL019400
PL012501
PL012502
VK000700
VH000902
VH001806
VC001000

Description
Bearing, Radial Ball, 5/8" ID, Snap Rings
Belt Roll Assembly, Output
Belt Roll, Input Assembly
Spacer, Output Tray
Shaft, Encoder Press Wheel
Shaft, Roll-Fold Wheel
Shaft, Input Roll
Shaft, Reversing
Shaft, Belt Guide
Shaft, Output Roll
Fold Wheel, Lower
Screw, Set, Socket, Cup Point, 1/4-20 x 1/4"
Press Wheel, Lower
Press Wheel, Lower, Output
Adjustment Block, Belt
Adjustment Screw Bar
Wrap Guide Mount
Sensor Bracket, Bottom
Sensor Bracket, Top
Belt, Panther H, 2" x 71.5" x .055"
Tray, Input
Keyless Bushing, 5/8" ID
Output Tray Weldment
Screw, Cap Head Socket, 1/4-20 x 1"
Washer, Flat, 1/4
Washer, Internal Lock, 1/4
Screw, Flat Head Socket, 1/4-20 x 3/4"
Screw, Button Head Socket, #10-32 x 1/2"
Washer, External Lock, #10
Screw, Button Head Socket, #10-32 x 1-1/4"
Screw, Flat Head Socket, #10-32 x 3/8"
Standoff, Card
Guide, Wrap, Operator Side
Guide, Wrap, Non-Operator Side
Guide Angle, Non-Operator Side
Guide Angle, Operator Side
Tray Extension, Operator Side
Tray Extension, Non-Operator Side
Bushing, Snap, Black, .625" Dia, .25" Thick Panel
Pulley Assembly, 18 Tooth, 3/8" Pitch, 1/2" Wide, Taper Lock
Pulley Assembly, 20 Tooth, 3/8" Pitch, 1/2" Wide, Taper Lock
Machine Key, 3/16" Square x .75", Square Ends, Undersize
Bracket, Frame Mounting
Nut, Hex, 1/4-20
Spur Gear, 48 Tooth, 32 Pitch, 3/16" Face, 14-1/2 Degree PA
Transport Encoder Assembly
Double Gearbelt, L, 3/8" Pitch, 1/2" Wide
Shaft, Registration Wheel Adjustment, Forward, Welded
Shaft, Drive Wheel Adjustment, Rear
Drive Wheel Support, Non-Operator Side
Drive Wheel Support, Operator Side
Knob, Black Phenolic, 2-3/8" Dia, Brass Insert
Screw, Flat Head Socket, #6-32 x 3/8"
Washer, Nylon, .375" ID x .625" OD x .032" Thick
Optical Sensor, Wide Gap

Quantity
10
1
1
4
1
1
1
1
1
1
2
1
3
1
2
2
2
2
2
3
1
1
1
17
8
18
4
26
38
12
6
4
1
1
1
1
1
1
2
3
1
2
4
1
1
1
1
1
1
2
2
1
10
8
2

56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100

VH008701
VH000505
VH000202
VH000603
PM010801
PM010803
PM012801
VH004102
PM011701
PM019800
VH007101
VH002503
VH002405
PL014400
PL020000
VH000207
VH007200
VH002501
VH007104
PT020400
PM018600
PM018700
VH001714
VH001813
PM019300
VT003904
VH000405
PF017800
VH009200
SM002902
VH004401
SE000800
SE006300
SE007301
SE007901
PP001400
VC004604
VH002108
PM011801
SE007400
VH008600
VH007300
VH007501
VH002502
PM016001

Machine Key, 3/16" Square x 1.75", Square Ends, Undersize
Screw, Flat Head Socket, #10-32 x 1"
Screw, Cap Head Socket, 1/4-20 x 1/2"
Screw, Flat Head Socket, 1/4-20 x 1"
Frame, Transport, Non-Operator Side
Frame, Transport, Operator Side
Tray Bar, Output
Collar, Locking, SS, 3/8" ID
Bearing Mount, Compound
Tray Bar, Input
Screw, Cap Head Socket, 5/16-18 x 2"
Washer, Split Lock, 5/16
Nut, Hex, 5/16-18
Stub Shaft, Hold Down Mount
Product Hold Down
Screw, Cap Head Socket, 1/4-20 x 1-1/2"
Screw, Hex Head, 1/4-20 x 3/4", Grade 5
Washer, Split Lock, 1/4
Screw, Cap Head Socket, 5/16-18 x 1"
Spacer, Modified, 3/16" x 3/8" OD x 1/2" Long
Bearing Block, Encoder-Fold
Bearing Block, Output
Screw, Set, Brass Tip, #10-32 x 3/8"
Washer, Nylon, .625" ID x 1.312" OD x .050" Thick
Pulley, 15 Tooth, L, 3/8" Pitch, Modified, 1/2" Wide, 5/8" Bore
Gearbelt, L, 3/8" Pitch, 1/2" Wide, 26 Groove
Screw, Button Head Socket, #10-32 x 3/4"
Spacer Strip, Tray Bar
Spring, Compression, .300" OD x .500" L x .042" Dia. MW
Knob, Black, #10-32 x 1-1/4"
Collar, Split, Clamp, 5/8" ID
Cable, Transport Encoder
Harness, Product Detector
Cable, Interlock
Cable, Stop Relay
Cable Mount
Clamp, Cable, 7/16", Nylon
Screw, Button Head Socket, #8-32 x 5/16"
Motor Plate
Assembly, Transport Motor
Washer, Stamping, C100819, Bokers, .387" ID x .870" OD x .187" Thick
Screw, Hex Head, 3/8-16 x 1-1/2", Grade 5
Washer, Flat, 3/8
Washer, Split Lock, 3/8
Pulley, 14 Tooth, 3/8" Pitch, 5/8" Bore, 1/2" Wide, 3/16" Keyway

1
4
2
2
1
1
2
4
1
3
1
1
1
2
2
3
4
4
1
1
1
1
7
4
2
1
1
1
1
1
4
1
1
1
1
1
3
3
1
1
4
4
4
4
1

SM012403 - FLOATING WRAP SECTION ASSEMBLY, W/BOGIES, 2 WRAP BELTS
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55

Part Number
PL014701
PL014801
PL014901
PL015001
PL019700
PL019000
PL020400
PL020500
PL017700
PL018101
VB001000
VH004401
PM015600
SM012700
PM015502
PM015501
VT003300
VH007701
VH008101
VH003804
VH006101
SM012800
SM012801
SM012900
SM012901
PL019200
VH006900
PL020501
VH008000
VK000800
VH001808
VH004103
PM016000
VT003600
VK000200
PL017900
VH003900
VH006001
VB000614
VK001500
PF014700
PW001900
PF013505
PL019500
VC005100
VC005200
VH002801
VH001202
VH000204
VH000405
VH000902
VH001712
VH002202
VH002404
VH003803

Description
Outer frame, Top, Operator Side
Outer frame, Top, Non-Operator Side
Inner Frame, Top, Operator Side
Inner Frame, Top, Non-Operator Side
Lift Bar
Belt Tensioner, Weldment
Shaft, Timing Belt, Fold, Split
Shaft, Timing Belt, Top, Operator Side
Shaft, Press Roll, Upper
Tie Bar, Inner Frame
Bearing, Radial Ball, 5/8" ID, Snap Rings
Collar, Split, Clamp, 5/8" ID
Pulley, 16 Tooth, 3/8" Pitch, 3/4" Wide, Modified
Pulley, Wrap Flange Assembly
Pulley, 1/5 Pitch, DF, 18 Tooth, 1/4" ID, Aluminum Hubless
Pulley, 1/5 Pitch, DF, 20 Tooth, 1/4" ID
Gearbelt, XL, 1/5 Pitch, 3/8" Wide, 40 Tooth
Spring, Compression, .360" OD x 1.250" L x .042" Dia. MW
Spring, Extension, .500" OD x 2.000" L x .049" Dia. MW
Nut, Hex, Self Locking, 1/4-20
Spacer, Nylon, .250" ID x .500" OD x .125" L
Pivot Block Assembly, Operator Side
Pivot Block Assembly, Non-Operator Side
Press Roll, Top, Operator Side
Press Roll, Top, Non-Operator Side
Spacer, Lift Bar
Screw, Shoulder, Socket Head, 3/8" x 5/8"
Shaft, Timing Belt, Top, Non-Operator Side
Rod Eyebolt, 3/8-16 x 3"
Knob, Thumb, 1-1/4" Dia., Thru Hole, Brass Insert
Washer, Nylon, .390" ID x .750" OD x .062" Thick
Collar, Locking, SS, 1/2" ID
Pulley, 19 Tooth, Modified
Gearbelt, L, 3/8" Pitch, 3/4" Wide, 72 Tooth
Knob, DK30, 1/4" ID, Black Phenolic, Brass Insert
Lock Pin, Wrap Section
Spring, Compression, .360" OD x .625" L x .026" Dia. MW
Retaining Ring, External, 1/4
Bearing, Oil Impregnated Bronze, Plain, 1/4" ID x 1/2" OD x 3/4" L
Handle, Lift, Wrap Section
Lexan Cover, Top, Wrap
Output Guard, Hinged
Input Top Guard
Lexan Spacer, Lift Bar
Reed Switch, SPST
Magnet
Screw, Button Head Socket, #4-40 x 5/16"
Insert, Threaded, #4-40
Screw, Cap Head Socket, 1/4-20 x 1"
Screw, Button Head Socket, #10-32 x 3/4"
Screw, Flat Head Socket, #6-32 x 3/8"
Screw, Set, Socket, Cup Point, 1/4-20 x 3/4"
Screw, Button Head Socket, #6-32 x 3/8"
Nut, Hex, 1/4-20
Nut, Hex, Self Locking, #6-32

Quantity
1
1
1
1
1
1
1
1
1
1
6
3
2
2
1
1
1
2
1
2
6
1
1
1
1
2
2
1
2
2
6
1
1
2
1
1
1
1
1
1
1
1
1
1
2
1
4
4
2
3
2
2
12
2
8

56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88

VH001811
VH001807
VH002904
VH002802
VH006401
PL014500
VH000602
VH000202
SM013001
VH000303
VH004102
VB000603
VH006800
VH000403
SM013101
VG000500
VH005003
PM018500
VH005006
VH001714
PL020600
VT004500
VH008701
VH009000
VH002413
VH010500
PL022400
VH000502
VH000402
VH001401
SM023200
VH000507
VH008700

Washer, Nylon, .640" ID x .781" OD x .031" Thick
Washer, Nylon, .505" ID x .750" OD x .032" Thick
Washer, Internal Lock, #4
Screw, Button Head Socket, #4-40 x 1/2"
Spacer, Nylon, .142" ID x .250" OD x .110" L
Idler, Spring Shaft
Screw, Flat Head Socket, 1/4-20 x 3/4"
Screw, Cap Head Socket, 1/4-20 x 1/2"
Idler Assembly, Belt Tensioner
E-Ring, External, 3/8
Collar, Locking, SS, 3/8" ID
Bearing, Oil Impregnated Bronze, Plain, 3/8" ID x 1/2" OD x 1/2" L
Washer, External Lock, #10
Screw, Button Head Socket, #10-32 x 1/2"
Bogie Wheel Assembly
O-Ring, 4-1/4" x 1/8" Dia.
Screw, Shoulder, Socket Head, 1/4" x 1"
Mounting Block, Bogie Wheel
Screw, Button Head Socket, #10-32 x 3/8"
Screw, Set, Brass Tip, #10-32 x 3/8"
Shaft, Bogie Wheel Assembly Mounting
Shaft Coupling w/Keyway
Machine Key, 3/16" Square x 1.75", Square Ends, Undersize
Ball Joint Rod End, 3/8-24
Nut, Hex, 3/8-24, Grade 5
Spacer, #8 x 3/8" OD x 1/2" L, Zinc-Plated Steel
Stub Shaft, 3/8" Dia.
Screw, Flat Head Socket, #10-32 x 3/8"
Screw, Button Head Socket, #10-32 x 3/8"
Washer, Flat, #10
Assembly, Output Drive Wheels
Screw, Flat Head Socket, #10-32 x 5/8"
Machine Key, 3/16" Square x .75", Square Ends, Undersize

2
2
4
2
2
1
4
2
1
1
1
2
1
1
2
4
2
2
2
2
2
2
2
4
4
1
1
1
2
2
1
1
3

SM022604 - BASE SUB ASSEMBLY, MCS TABBER (2")
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55

Part Number
SM009703
SM010001
SM012002
SM009100
SM012403
SM008300
SM008000
SE006901
VC004601
SE000110
SE001100
PP000500
PP000600
PP000900
PP001000
PP001200
PP001601
PP001602
PP001700
PA007800
PA008400
PA008500
PA008600
PP001300
VK001000
VT003902
PM017000
SM024000
VK001100
PL013200
VZ002300
VH000303
PF016203
PF017100
PL020201
PL020200
PL020203
PF017200
PF017201
PL020202
PL020204
PF017103
VH000402
VH006800
VH003801
VH001401
VH007201
VH001404
VH000102
VH002404

VH002801
VH002904
VH002402

Description
Lower Frame Assembly, MCS 2" Caster
Upper Frame Assembly
Transport Assembly
Registration Wheel Assembly
Floating Wrap Section Assembly, 2 Wrap Belts
Front Panel Assembly
Assembly, Base Connector Plate
Harness, Base Cover Interlock
Clamp, Cable, 1/8", Nylon
PCB Assembly, Taber Control
Cable, DC Power Supply
Angle Support, Hinge, Non-Operator Side
Cover, Hinge, Non-Operator Side, Formed
Guard, Input, Top
End Cap, Non-Operator, Frame, Input
Cover, Fixed, Non-Operator Side
Cap, Non-Operator, Outer Frame, Bracket #1
Cap, Operator Side, Outer Frame, Bracket #2
Operator Outer Frame Cover
Cover, Output, Top
Cover, Base, Top, Output End
Cover, Base, Top, Input End
Output Cover, Non-Operator Side
Cover, Hinged, Fixed, Formed
Crank Handle, 2.5", 1/2" ID
Gearbelt, L, 3/8" Pitch, 1/2" Wide, 68 Tooth
Piano Hinge, 2 Feet
Mounting Plate, Tabber Control Board
Knob, Black w/#10-32 Stud
Angle, Output Guard
Brush, Static
E-Ring, External, 3/8
Bridge Angle, 3"
Guide
Cap, Guide Mount
Cap, Strap Mount
Shaft, Guide & Strap
Bracket, Square Shaft Mount, Operator Side
Bracket, Square Shaft Mount, Non-Operator Side
Mount Block, Strap
Mount Block, Guide
Strap, Deflector
Screw, Button Head Socket, #10-32 x 3/8"
Washer, External Lock, #10
Nut, Hex, Self Locking, #10-32
Washer, Flat, #10
Screw, Hex Head, 1/4-20 x 2", Grade 5
Washer, Flat, 1/4
Washer, Internal Lock, 1/4
Nut, Hex, 1/4-20

Screw, Button Head Socket, #4-40 x 5/16"
Washer, Internal Lock, #4
Nut, Hex, #6-32

Quantity
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
2
1
1
2
1
1
1
2
1
1
1
2
1
2
64
58
2
2
12
12
4
4

3
3
14

56
57
58
59
60
61

VH000403
VH006901
VH009100
PP002300
PL021600
PT017900

Screw, Button Head Socket, #10-32 x 1/2"
Screw, Shoulder, Socket Head, 5/16-18 x 3/8" x 1"
Spring, Compression, .480" OD x .875" L x .036" Dia MW
Bracket, Center Belt Shift
Shaft, Vertical Belt Guide
Tube, Vertical Belt Guide

2
4
3
1
2
2

User’s Guide

MCSPRO-1020
Tabbing System

MCS Incorporated
8101 Cessna Avenue
Gaithersburg, MD 20879

REV-AA

MCSPRO-1020 Tabbing System User’s Guide

FIGURE 1 – TRANSPORT BASE

MCSPRO-1020 Tabbing System User’s Guide

FIGURE 2 - TABBING HEAD

MCSPRO-1020 Tabbing System User’s Guide

Base Power Rocker Switch
Head Power Rocker Switch
Jog Push Button Switch
Start Push Button Switch
Transport Speed Potentiometer

3.1.1 Base Power Rocker Switch
This switch controls power to the tabber base. This switch must be on and lit in order for the
transport base to function.

3.2 Operator Interface
MCSPRO-1020 Tabbing System User’s Guide

SETUP

MEMORY

ONLINE

ENTER

TEST

POSITION

MCSPRO-1020 Tabbing System User’s Guide

Loosen transport table locking lever. (See Figure 5)
Position transport table to dimension given. (See Figure 4)

Figure 4

MCSPRO-1020 Tabbing System User’s Guide

5.
6.

Figure 5

MCSPRO-1020 Tabbing System User’s Guide

FIGURE – 6

4.1.3 Ink Jet Base Setup
All requirements concerning feeding, printing and product position should be met before feeding
product through tabber.

4.1.4 Adjust Transport Table Position
Requirement:
Adjust transport table to edge of product path.
Procedure:
1.
2.
3.

MCSPRO-1020 Tabbing System User’s Guide

Figure 7

4.1.5 Product Guide and Strap Usage
Procedure:
1.

Mount strap assemblies (2) provided to square shaft (See Figure 8).

Note: Straps may be positioned on product to control flatness as desired or removed by loosening
screw and rotating retainer cap 180 degrees.
2.

Mount Product Guide (See Figure 9).

MCSPRO-1020 Tabbing System User’s Guide

Strap Assemblies
Screws

Figure 9

Figure 8

Requirement:
The top wrap section must be gapped to product thickness to effectively wrap tabs or secure
labels.
Procedure:
1.

Rotate Product Thickness Crank (See Figure 10) clockwise. Insert product sample to be
tabbed between upper output belt and output roller below.

Rotate crank counterclockwise until firm pressure is felt by pulling product sample from
the belt-roller.

Figure 10

MCSPRO-1020 Tabbing System User’s Guide

Procedure:
1.

Loosen lever locks (See Figure 11). Position registration wheel assembly over belt
adjacent to guide rail.

Adjust angle drive wheel knob to angle three slaved wheels towards guide rail (See Figure
11). Do not adjust wheels to maximum angle. Use minimum angle, increase only as
necessary.

When the requirements above have been met, tabbing operation can proceed.

MCSPRO-1020 Tabbing System User’s Guide

Figure 12

Figures 11 & 12

Fine Adjust Limit Stop Knob
Deflector Strip

Wheel Lift Knob

Figure 13

MCSPRO-1020 Tabbing System User’s Guide

4.1.10 Output Drive Wheels
Figure 14
Output Drive Wheel Assembly

An Output Drive Wheel Assembly is provided in the Wrap Section (See Figure 14). These
wheels assist in controlling the mailpiece when the Wrap Section is gapped.

Figure 15
Button Head Screw

MCSPRO-1020 Tabbing System User’s Guide

4.1.11 Center Belt Adjustment
Figure 16

Center Transport Belt

Adjuster Knobs

Requirement: Adjust Center Belt position to support Product Edge.
Note: Transport Base must be powered up to move center belt..
Procedure:
1.
2.
3.
4.

MCSPRO-1020 Tabbing System User’s Guide

Note:
For labeling or stamp affixing requirements, press rolls (1) through (4) may be positioned in
various configurations in front of the peel point to meet size
requirements.

Figure 17

MCSPRO-1020 Tabbing System User’s Guide

Figure 18

MCSPRO-1020 Tabbing System User’s Guide

Figure 19

Figure 20

Inner Frame

Brass Tip Set Screw
Pressure on Belt

Screw Head & Spacer
5.
6.

Lower wrap section to operating position and secure with swing bolts and knobs.
Turn product thickness adjust counterclockwise to zero stop position (See Figure 21).
Figure 22

Figure 21

Swing Bolt & Knob
Product Thickness Adjust

Block Resting on Screw Head

Raise upper wrap section to lock position. Secure brass tip set screw. See Figure 19.
Repeat all procedures above for non-operator’s side.

Note: The idler wheel assembly is now adjusted to its correct position and will give tight wrap on
all product when the upper wrap assembly is correctly gapped (See Section 4.1.6 Set Gap).

MCSPRO-1020 Tabbing System User’s Guide

ensure that the take-up roll cannot slip on the hub of the inner spool support. The Take-up Full
Sensor must be located to sense the waste tab/label liner for overflow detection.

MCSPRO-1020 Tabbing System User’s Guide

4.2.8 Tab/ Label Position Entry

MCSPRO-1020 Tabbing System User’s Guide

LEADING EDGE

Product Flow

Tab Position 1
Tab Position 2
Tab Position 3

MCSPRO-1020 Tabbing System User’s Guide

Tab Pitch
Job Memory
Auto Tab Calculator Product Size
Product/ Tab Sensor Offset
Tab Sensor Sensitivity
Counter Reset
Product Sensor Selection

5.1.4 Product/ Tab Sensor Offset

Procedure
1) Take the system offline.
MCSPRO-1020 Tabbing System User’s Guide

LEADING EDGE

Product Flow

Tab Position 1
Tab Position 2
Tab Position 3

Procedure
1) Take the system offline.
2) Press the “POSITION” key to access the test menu. “POSITION” should be displayed
on the first line of the display.
3) Press either the “” or “” until “TAB POS x: yy.yy>_” is displayed on the second line
of the display. The x represents the tab position of interest and the yy.yy represents the
current setting for that tab position.
4) To increase the Tab Position from the leading edge press the “+” until the desired
location is displayed as the current setting. To decrease the Tab Position from the leading
edge press the “-“ until the desired location is displayed as the current setting.
-Or5) The desired position can be directly entered from the numeric keypad.
6) As the new setting is entered it appears to the right of the current setting.
7) Once entry of the new value is completed press the “ENTER” key to save the new value.
The LCD will indicate completion by replacing the current setting with the new setting.

5.2.2 Number of Tabs
The unit can apply 1 to 3 tabs on a single product in one pass. The “POSITION” key
gives access to this setting.

Procedure
1) Take the system offline.
MCSPRO-1020 Tabbing System User’s Guide

3) Press either the “” or “” until “VERSION X.X” is displayed on the second line of the
display. (X.X will be the version number of interest)

MCSPRO-1020 Tabbing System User’s Guide

4) The LCD display will indicate the current state of the bin sensor while this test is being run.

MCSPRO-1020 Tabbing System User’s Guide

Chapter 6 – Troubleshooting

MCSPRO-1020 Tabbing System User’s Guide

Chapter 7 – Appendix
FIGURE A1 – BASE CONTROL SYSTEM DIAGRAM

MCSPRO-1020 Tabbing System User’s Guide

FIGURE A2 – HEAD CONTROL SYSTEM DIAGRAM

MCSPRO-1020 Tabbing System User’s Guide

FIGURE A3 – HEAD SYSTEM DIAGRAM

MCSPRO-1020 Tabbing System User’s Guide

ILLUSTRATED PART BREAKDOWN
WASTE TAKE-UP SENSOR
P/N SE001400

TAB GUIDE, O-RING
P/N VG000100
TAB GUIDE, SPLIT RING
P/N PT002400

BIN SENSOR
P/N SE001200

TAB SENSOR ASSEMBLY
LABEL SENSOR ASSEMBLY

P/N SM002700 (2”)
P/N SM002701 (4”)

MCSPRO-1020 Tabbing System User’s Guide

KNOB, QUICK ACTING, ½ -13 P/N VK000600 (QTY 2)
UNWIND SPOOL ASS’Y, TABBER
UNWIND SPOOL ASS’Y, LABELER

P/N SM001800 (2“)
P/N SM001801 (4”)

UNWIND SPOOL SUPPORT ASS’Y

TAKE-UP SPOOL ASS’Y, TABBER
TAKE-UP SPOOL ASS’Y, LABELER

P/N SM001604

P/N SM001900 (2“)
P/N SM001901 (4”)
IDLER ASS’Y, UNWIND DRIVE, TABBER P/N SM002200 (2“)
IDLER ASS’Y, UNWIND DRIVE, LABELER P/N SM002201 (4”)

URETHANE ROLLER, FLOAT IDLER, TABBER (2“) P/N VR000200
URETHANE ROLLER, FLOAT IDLER, LABELER (4“) P/N SM008401

TAKE-UP SPOOL SUPPORT ASS’Y

P/N SM001102

URETHANE ROLLER, UNWIND DRIVE, TABBER P/N VR000300
URETHANE ROLLER, UNWIND DRIVE, LABELER P/N VR000301

FRONT HEAD GUARD (SHOWN OPEN) P/N SM000501

DRIVE ROLL, TABBER (GRIT WHEEL)
DRIVE ROLL, LABELER (GRIT WHEEL)
IDLER ASS’Y, TAB DRIVE
IDLER ASS’Y, LABEL DRIVE

P/N PM003500 (2“)
P/N PM003501 (4“)

P/N SM002100 (2“)
P/N SM002101 (4”)

MCSPRO-1020 Tabbing System User’s Guide

P/N VB000102

P/N VB000102
SHAFT, SPOOL ,TABBER
SHAFT, SPOOL, LABELER

SPUR GEAR, 40 TOOTH, ½” BORE

P/N PM010500

SPUR GEAR, 20 TOOTH, ¼” BORE

BEARING, ½” ROLLER

P/N PL011103 (2”)
P/N PL011101 (4”)

SPUR GEAR, 18 TOOTH, 3/8” BORE
P/N PM010400

P/N VB000102

P/N PM006300

SPUR GEAR, 36 TOOTH, ¼” BORE

SPUR GEAR, 30 TOOTH, 1/4” BORE

P/N PM006100

P/N PM006400

SPUR GEAR, 30 TOOTH, 1/2” BORE P/N PM006200
BEARING, 3/8” ROLLER P/N VB000101

P/N VM000301

P/N VM000202

P/N AM000102

P/N VM000301

WRAP GUIDE, NON-OP. SIDE

WRAP GUIDE, OP. SIDE

P/N PL017301

P/N PL017300

SPUR GEAR, 48 TOOTH, 32 PITCH

P/N VB001000
P/N SM009000
P/N VB001000

MCSPRO-1020 Tabbing System User’s Guide

P/N VT002500

BELT ROLL,OUTPUT P/N SM008701
BELT ROLL, INPUT P/N SM010900

SHAFT, INPUT ROLL

P/N PL016800

SHAFT, INPUT BELT GUIDE P/N PL017000

P/N VB001000

PULLEY, 18 TOOTH, 3/8”PITCH, ½” WIDE

P/N SM013200

P/N VB001000

PULLEY, 14 TOOTH, 3/8”PITCH, ½” WIDE P/N PM016001

P/N SM008701

SHAFT, OUTPUT BELT GUIDE P/N PL020100
SHAFT, LOWER FOLD WHEEL P/N PL016700
P/N PM016300

P/N VT003902
P/N VB001000

SHAFT, LOWER OUTPUT ROLL P/N PL017100

P/N VB001000

P/N SM013200

PULLEY, 20 TOOTH, 3/8”PITCH, ½” WIDE P/N SM013201
SHAFT, REVERSING P/N PL016901

MCSPRO-1020 Tabbing System User’s Guide

TABBER CONTROL BOARD
SE000110

BASE ENCODER ASSEMBLY
SM009000
MOTOR SPEED CONTROL
ME000400

24VDC POWER SUPPLY
VC014300

MCSPRO-1020 Tabbing System User’s Guide

PRODUCT SENSOR
VC001000

RED MUSHROOM
PUSHBUTTON SWITCH
VC014600

BLACK PUSHBUTTON SWITCH
VC014602

THERMAL CIRCUIT
BREAKER/SWITCH 10A
VC014701

GREEN PUSHBUTTON
SWITCH VC014601

THERMAL CIRCUIT
BREAKER/SWITCH 5A
VC014700

GEARBELT, URETHANE, ¾”w x 72 TOOTH
VT003600

TRANSPORT BELTS, 2”w x 46-1/2”L (SET OF 4)
VT003402

TRANSPORT BELTS, 2”w x 27”L (SET OF
4)

LOWER FOLDWHEEL, URETHANE COATED (2)
PM016200

LOWER PRESSWHEEL, URETHANE COATED
(4)

MCSPRO-1020 Tabbing System User’s Guide

PULLEY, 19 TOOTH, 3/8”PITCH,1/2” WIDE
BEARING, RADIAL BALL, 5/8” W/SNAP RING

P/N

PM016000

VB001000
P/N

SHAFT, UPPER OUTPUT

P/N

VB001000

PL017400

P/N

PM015600

PULLEY, 16 TOOTH, 3/8”PITCH, ¾” WIDE P/N PM015600
P/N
P/N

VT003600

VT003600
BEARING, ROLLER, 5/8” I.D. P/N
PULLEY, FOLD FLANGE

PULLEY, 20 TOOTH,1/5”PITCH

P/N

VB000104

SM012700

PM015501

P/N

SM012700
P/N

VB001000

P/N VB001004
P/N VB001000
P/N PL019100

SHAFT, UPPER FOLD WHEEL

P/N

PL017500

PL019100

P/N VT003300
P/N VB000102

PULLEY, 18 TOOTH,1/5”PITCH

P/N PM015502

PRESS ROLL, UPPER OP. SIDE

P/N SM012900

SHAFT, UPPER PRESS ROLL

BEARING, ROLLER, 1/2” I.D.
PRESS ROLL, UPPER NON-OP. SIDE

P/N

PL017700

MCSPRO-1020 Tabbing System User’s Guide

P/N VB000102
SM012901

MISCELANIOUS SPARE PARTS NOT LISTED ABOVE
TABBING HEAD

VC006200
VH001900
VH003300

HEAD POWER SUPPLY FUSE
EXTENSION SPRING, 0.25” OD x 1.75” L (UNWIND REAL)
EXTENSION SPRING, 0.25” OD x 1.5” L (TAKE UP)

TABBING BASE
SE000202

OPERATOR INTERFACE

MCSPRO-1020 Tabbing System User’s Guide

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
XMP Toolkit                     : 3.1-702
Modify Date                     : 2008:12:26 11:59:50-05:00
Create Date                     : 2008:12:26 11:59:50-05:00
Metadata Date                   : 2008:12:26 11:59:50-05:00
Creator Tool                    : PScript5.dll Version 5.2
Format                          : application/pdf
Title                           : Microsoft Word - USER'S GUIDE REV-AA.DOC
Creator                         : Lou
Document ID                     : uuid:7fd35358-a3b7-4c5b-b989-77613c789be4
Instance ID                     : uuid:051ca64c-2e6b-49dd-8de9-0dfc3cfc32b5
Producer                        : Acrobat Distiller 6.0 (Windows)
Has XFA                         : No
Page Count                      : 175
Author                          : Lou

EXIF Metadata provided by EXIF.tools

USER'S GUIDE REV AA Tabber User Parts

Navigation menu

Versions of this User Manual:

Views

Navigation