PW8000ST User Manual Issue1.4 UPS 454 01 02 PW8000DPA ST 1.4.1

• Safety
  • 1.1 Description of symbols used in this manual
  • 1.2 User precautions
• General Description
  • 2.1 Reliability and Quality Standards
  • 2.2 PW8000DPA ST System
  • 2.3 System Configuration
  • 2.4 Advanced Design Features
    • 2.4.1 Input booster technology
    • 2.4.2 Flexible battery management
    • 2.4.3 Decentralized Parallel Architecture (DPA)
  • 2.5 Warranty
    • 2.5.1 Extended warranty
    • 2.5.2 Additional service/maintenance support
  • 2.6 Extended Service enquiry form
• Installation
  • 3.1 Introduction
  • 3.2 Receipt of the UPS
    • 3.2.1 Site transportation
  • 3.3 Unpacking
    • 3.3.1 Nameplate
  • 3.4 Batteries
  • 3.5 Storage
    • 3.5.1 UPS
    • 3.5.2 Battery
  • 3.6 Positioning
    • 3.6.1 Planning the installation
  • 3.7 UPS Power Cabling (preparation and planning)
    • 3.7.1 General requirements
      • Input neutral grounding
  • 3.8 Connecting the UPS input supply
    • 3.8.1 Safety notes
    • 3.8.2 Preparing the input cabling
    • 3.8.3 Connecting the UPS input power cables
      • Single Input Feed
      • Dual Input Feed
  • 3.9 Connecting the UPS Output Supply
    • 3.9.1 Safety notes
    • 3.9.2 Preparation for the output cabling
    • 3.9.3 Connecting the UPS output cables
  • 3.10 Connecting the batteries
    • 3.10.1 Safety Notes
    • 3.10.2 Battery cabling
      • Battery configuration options
      • Common battery configuration
    • 3.10.3 Connecting the battery cables
    • 3.10.4 Internal battery for ST-40 and ST-60 cabinets
      • Important notes:
    • 3.10.5 External battery enclosures
  • 3.11 Module interfacing facilities
    • 3.11.1 Smart Port JD1 (Serial RS 232) and USB Port
    • 3.11.2 X1 & X2 Dry Port (volt-free contacts)
      • Input Interfaces Terminal block X1
      • Output Interfaces Terminal blocks X2 (DRY PORTs)
• Operation
  • 4.1 Commissioning
  • 4.2 UPS control panel
    • 4.2.1 Power Management Display (PMD)
    • 4.2.2 Mimic LED indicators
      • LED Indication summary
    • 4.2.3 Operator keys
      • Key function summary
      • ON/OFF Start-up and shutdown buttons
  • 4.3 Description of the LCD display
    • 4.3.1 Status screens
    • 4.3.2 Main menu screen
    • 4.3.3 Event log menu screen
    • 4.3.4 Measurements menu screen
    • 4.3.5 Commands menu screen
    • 4.3.6 UPS Data menu screen
    • 4.3.7 Set-Up Service menu screen
    • 4.3.8 Set-up User menu screen
    • 4.3.9 Set-Up Service menu screen
  • 4.4 Operating modes
    • 4.4.1 On-line (inverter) mode
    • 4.4.2 On-bypass (line-interactive) mode
    • 4.4.3 Maintenance bypass mode
      • Maintenance bypass switch (IA1)
  • 4.5 Operating Instructions
    • 4.5.1 Starting the UPS system from the maintenance bypass
      • Powering up the UPS module(s):
      • Transferring the load to the UPS from the Maintenance Bypass:
    • 4.5.2 Individual UPS module start/stop procedure
      • UPS module shut-down:
      • UPS module start-up:
    • 4.5.3 Transfer to maintenance bypass mode
      • Transferring the UPS to the on-bypass mode:
      • Closing the maintenance bypass switch:
      • Powering down a UPS module:
    • 4.5.4 Complete system shutdown
  • 4.6 Replacing a UPS module in a single module system
    • 4.6.1 Extracting the UPS module
    • 4.6.2 Refitting the UPS module
  • 4.7 Replacing a UPS module in a REDUNDANT multi-module system
    • 4.7.1 Extracting the UPS module
    • 4.7.2 Refitting the UPS module
  • 4.8 Replacing a UPS module in a CAPACITY multi-module system
    • 4.8.1 Extracting the UPS module
    • 4.8.2 Refitting the UPS module
• Maintenance
  • 5.1 Introduction
  • 5.2 System calibration
  • 5.3 User responsibilities
  • 5.4 Routine maintenance
  • 5.5 Battery testing
  • 5.6 Battery maintenance
  • 5.7 Battery disposal and recycling
• Troubleshooting
  • 6.1 Alarms
  • 6.2 Menu, Commands, Event Log, Measurements,
  • 6.3 Fault Identification and Rectification Messages and Alarms
  • 6.4 Contacting Service
• Options
  • 7.1 Introduction
  • 7.2 Remote emergency stop
  • 7.3 Generator ON facilities
  • 7.4 UPS Monitoring and automated control software
    • 7.4.1 SNMP Card slots
    • 7.4.2 The importance of UPS management
      • SNMP monitoring software
      • WAVEMON UPS monitoring and control software
    • 7.4.3 WAVEMON Shutdown and Monitoring Software
    • 7.4.4 Functional description
    • 7.4.5 Licensing
    • 7.4.6 RCCMD Server shutdown
  • 7.5 PowerREPORTER™ management software
    • 7.5.1 Functional description
• Specification
  • 8.1 Mechanical Characteristics – UPS Cabinet
  • 8.2 Mechanical Characteristics – UPS Module
  • 8.3 Input Characteristics
  • 8.4 Battery Characteristics
  • 8.5 Battery Capacity Usage
  • 8.6 Heat Dissipation Per Module With Non-Linear Load
  • 8.7 Output Characteristics
  • 8.8 Standards
  • 8.9 Environmental Characteristics
  • 8.10 Communication Options
  • 8.11 Fuses & Cables Quick Reference