Mitsubishi Digital Electronics Projection Television WD 73727

Mitsubishi Digital Electronics Projection Television WD-52628 WD-52628

User Manual: Mitsubishi Digital Electronics Projection Television WD-73727

Open the PDF directly: View PDF .
Page Count: 124

Download
Open PDF In Browser	View PDF

WD-52628
WD-62628
WD-73727
Projection Television
Owner’s Guide

TV Information
Use this space to record the model number and serial
number of your television. This information is on the back
of your TV.
Model Number
Serial Number
Purchase Date

visit our website at
www.mitsubishi-tv.com

CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user of the
presence of uninsulated “dangerous voltage” within the product’s enclosure that may be sufficient magnitude
to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
This TV is heavy! Exercise extreme care when lifting or moving. Lifting or moving the TV requires a minimum of two
adults. To prevent damage to your TV, your TV should not be jarred or moved while it is turned on. Power off your TV
before moving it.
Portions of the advanced circuitry of this TV must continue to operate even when the TV is turned off. Some of these
circuits therefore need to be cooled at all times. A low power standby fan may be heard in a quiet environment. This is
normal operation.

Custom cabinet installation must allow for proper air circulation around the television.
TV Guide On Screen® Access Requirements

TV Guide On Screen listings are not provided by Mitsubishi Digital Electronics America, Inc. Operation of TV Guide On
Screen requires over-the-air or cable access to stations carrying TV Guide On Screen program listings. If listings are
not available in your area or become discontinued by the local provider, TV Guide On Screen will not operate. TV Guide
On Screen does not provide program listings for satellite TV systems.

Stand Requirement

CAUTION: Use these Mitsubishi TV models only with
the Mitsubishi stand models shown here. Use with other
stands can result in instability and possibly cause injury.

TV Model Number

Stand Model Number

WD-52628

MB-52528

WD-62628

MB-62528

WD-73727

MB-73727

Lamp Replacement
The image on this TV is produced by a powerful lamp that will operate for many hours. Eventually, however, this lamp
will need to be replaced. It is designed to be easily replaced by the TV owner. Front panel indicators and/or on-screen
messages will assist you in determining when the lamp needs to be replaced. Please see Appendix H for details on
lamp replacement. To order a new lamp:
While Under Warranty
Call (800) 332-2119. Please
have model number, serial
number, and TV purchase
date available.

After Warranty
Call (800) 553-7278. Order a new lamp for your TV model as shown below.
TV Model Number

Lamp Part Number

WD-52628, WD-62628

915P026010

WD-73727

915P027010

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
NOTE TO CATV SYSTEM INSTALLER: THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER’S
ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR THE PROPER GROUNDING AND,
IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF
THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL.

FCC Declaration of Conformity
Product:

Projection Television Receiver

Models:

WD-52628, WD-62628, WD-73727

Responsible Party:

Mitsubishi Digital Electronics America, Inc.
9351 Jeronimo Road
Irvine, CA 92618-1904

Telephone:

949-465-6000

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

CAUTION: To ensure continued FCC compliance, the user must use a shielded video interface
or HDMI cable with bonded ferrite cores at both ends when using the PC input.
Changes or modifications not expressly approved by Mitsubishi could cause harmful interference and would
void the user’s authority to operate this equipment.

IMPORTANT SAFEGUARDS

Please read the following safeguards for your TV and retain for future reference. Always follow all warnings
and instructions marked on the television.
1. Read, Retain and Follow All Instructions
Read all safety and operating instructions before operating the TV. Retain the safety and operating instructions
for future reference. Follow all operating and use instructions.

2. Heed Warnings
Adhere to all warnings on the appliance and in the operating instructions.

3. Cleaning
Unplug the TV from the wall outlet before cleaning. Do not use liquid, abrasive or aerosol cleaners. Cleaners
can permanently damage the cabinet and screen. Use a lightly dampened cloth for cleaning.

4. Attachments and Equipment
Never add any attachments and/or equipment without approval of the manufacturer as such additions may
result in the risk of fire, electric shock or other personal injury.

5. Water and Moisture
Do not use the TV where contact with or immersion in water is possible. Do not use near bath tubs, wash
bowls, kitchen sinks, laundry tubs, swimming pools, etc.

6. Accessories
Do not place the TV on an unstable cart, stand, tripod, or table. The TV may fall, causing
serious injury to a child or adult and serious damage to the TV. Use only with a cart, stand,
tripod, bracket or table recommended by the manufacturer, or sold with the TV. Any mounting
of the TV should follow the manufacturer’s instructions, and should use mounting accessories
recommended by the manufacturer.
An appliance and cart combination should be moved with care. Quick stops, excessive force,
and uneven surfaces may cause the appliance and cart combination to overturn.

7. Ventilation
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the TV and
to protect it from overheating. Do not block these openings or allow them to be obstructed by placing the TV
on a bed, sofa, rug, or other similar surface. Nor should it be placed over a radiator or heat register. If the TV
is to be placed in a rack or bookcase, ensure that there is adequate ventilation and that the manufacturer’s
instructions have been adhered to.

8. Power Source
This TV should be operated only from the type of power source indicated on the marking label. If you are not
sure of the type of power supplied to your home, consult your appliance dealer or local power company.

9. Grounding or Polarization
This TV is equipped with a polarized alternating current line plug having one blade wider than the other. This
plug will fit into the power outlet only one way. If you are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do
not defeat the safety purpose of the polarized plug.

10. Power-Cord Protection
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point
where they exit from the TV.

11. Lightning
For added protection for this TV during a lightning storm, or when it is left unattended and unused for long
period of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent
damage to the TV due to lightning and power-line surges.

IMPORTANT SAFEGUARDS, continued
12. Power Lines
An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or
power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such power lines or circuits as contact with them might be
fatal.

13. Overloading
Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

14. Object and Liquid Entry
Never push objects of any kind into this TV through openings as they may touch dangerous voltage points or
short-out parts that could result in fire or electric shock. Never spill liquid of any kind on or into the TV.

15. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the TV, be
sure the antenna or cable system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Article 810 of the National Electric Code, ANSI/NFPA No. 70-2002,
provides information with respect to proper grounding of the
mast and supporting structure, grounding of the lead in wire to an
antenna discharge unit, size of grounding conductors, location of
antenna discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.

16. Servicing

E XAMP LE OF ANT E NNA G R OUNDING

ANT E NNA
LE AD IN WIR E
G R OUND C LAMP

E LE C T R IC
S E R V IC E
E QUIP ME NT

ANT E NNA
DIS C HAR G E UNIT
(NE C AR T IC LE 810-20)
G R OUNDING
C ONDUC T OR S
(NE C AR T IC LE 810-21)
G R OUND C LAMP S

NE C — NAT IONAL E LE C T R IC AL C ODE

P OWE R S E R V IC E G R OUNDING
E LE C T R ODE S Y S T E M
(NE C AR T 250, P AR T H)

Do not attempt to service this TV yourself as opening or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service personnel.

17. Damage Requiring Service
Unplug the TV from the wall outlet and refer servicing to qualified service personnel under the following
conditions:
(a)
(b)
(c)
(d)

When the power-supply cord or plug is damaged.
If liquid has been spilled, or objects have fallen into the TV.
If the TV has been exposed to rain or water.
If the TV does not operate normally by following the operating instructions, adjust only those controls that
are covered by the operating instructions as an improper adjustment of other controls may result in damage
and will often require extensive work by a qualified technician to restore the TV to its normal operation.
(e) If the TV has been dropped or the cabinet has been damaged.
(f) When the TV exhibits a distinct change in performance - this indicates a need for service.

18. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts specified by
the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in
fire, electric shock or other hazards.

19. Safety Check
Upon completion of any service or repair to the TV, ask the service technician to perform safety checks to
determine that the TV is in safe operating condition.

20. Heat
The product should be situated away from heat sources such as radiators, heat registers, stoves or other
products (including amplifiers) that produce heat.

Contents
Chapter 1: Television Overview
TV Accessories.. . . . . . . .
Special Features.. . . . . . .
Front Control Panel. . . . .
Remote Control
Overview. . . . . . . . . . .
Battery Installation . .
Care. . . . . . . . . . . . . . .
Sleep Timer.. . . . . . . .
TV Back Panel.. . . . . . . . .
Memory Card Reader. . .
System Reset Button.. . .
TV Reset Menu.. . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10
11
12
14
15
15
15
16
18
20
20

Chapter 2: Connecting
External Devices and NetCommand® Setup. . . . . . . . . . . . . . . . . .
Using a CableCARD.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wall Outlet Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standard Cable Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Antenna with a Single Lead. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Antennas with Separate UHF and VHF Leads. . . . . . . . . . . . . . . . .
VCR to an Antenna or Wall Outlet Cable (Audio & Video).. . . . . . .
VCR to a Cable Box (Audio & Video). . . . . . . . . . . . . . . . . . . . . . . . .
A/V Receiver (Stereo System). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Satellite Receiver or Other Device with S-Video. . . . . . . . . . . . . . .
DVD Player with Component Video. . . . . . . . . . . . . . . . . . . . . . . . . .
DVI Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HDTV Cable Box or Satellite Receiver with Component Video . .
HDMI Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Computer with an HDMI Monitor Output.. . . . . . . . . . . . . . . . . . . . .
Computer with a DVI Monitor Output.. . . . . . . . . . . . . . . . . . . . . . . .
IR Emitter NetCommand®. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compatible IEEE 1394 Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Helpful Hints for NetCommand Connections. . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .

22
23
24
24
25
25
26
27
28
28
29
29
30
30
31
31
32
33
35

Chapter 3: NetCommand® Setup and Editing
NetCommand® Introduction. . . . . . . . . . . . . . . . . . . .
Using the Remote Control with NetCommand® .. .
NetCommand® Setup On-Screen Buttons. . . . . . .
Menu System. . . . . . . . . . . .
3D Graphical
NetCommand® Initial Setup. . . . . . . . . . . . . . . . . . . .
Edit NetCommand®: Add an A/V Receiver. . . . . . .
Edit NetCommand®: Add Devices .. . . . . . . . . . . . .
Edit NetCommand®: Change or Delete Devices. .
IEEE 1394 Devices and NetCommand® Control.. .
Adding IEEE 1394 Devices Automatically. . . . . . . . .

38
39
40
41
42
45
48
52
53
54

Chapter 4: NetCommand® Functions
Device Selection Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Device Menu Button to Display Menus. . . . . . . . . . . . . .
Using the GUIDE Button to Display ChannelView™ and Menus.
NetCommand®-Controlled Recordings. . . . . . . . . . . . . . . . . . . . . .
Peer-to-Peer Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using A/V Discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

58
59
60
61
63
64

Chapter 5: TV Menu Operations
Main Menu.. . . . . . . . . . . .
Setup Menu . . . . . . . . . . .
NetCommand® Menu . .
Record Menu. . . . . . . . . .
Channel Menu . . . . . . . . .
Captions Menu. . . . . . . . .
V-Chip Lock Menu. . . . . .
Audio/Video Menu. . . . . .
Audio Settings.. . . . . . . . .
Video Settings.. . . . . . . . .

66
67
69
70
72
74
76
79
80
81

Chapter 6: Additional Features
MediaCommand™ and Memory Card Playback. .
Operation of PIP and POP. . . . . . . . . . . . . . . . . . . . .
TV Display Formats. . . . . . . . . . . . . . . . . . . . . . . . . . .
PC Viewing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PC Display Formats.. . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

84
86
87
89
90

Chapter 7: Troubleshooting.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Appendices
Appendix A:
Appendix B:
Appendix C:
Appendix D:
Appendix E:
Appendix F:
Appendix G:
Appendix H:
Appendix I:

Specifications.. . . . . . . . . . . . . . . . . . . . . . . . .
On-Screen Information Displays.. . . . . . . . .
Bypassing the V-Chip Lock.. . . . . . . . . . . . .
Remote Control Programming Codes. . . . .
Device Control with NetCommand®. . . . . .
NetCommand® Specialized Device Keys. .
Cleaning and Service. . . . . . . . . . . . . . . . . . .
Lamp Cartridge Replacement.. . . . . . . . . . .
Recording and Viewing Combinations.. . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

100
102
103
105
108
110
111
112
114

Trademark and License Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

116

Mitsubishi DLP™ Projection Television Limited Warranty.. . . . . . . . . . . . . . . . . . . .

118

Index.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

120

Our Thanks...
Thank you for choosing Mitsubishi as your premier Home Entertainment provider

This Owner’s Guide describes the features and functions of your Mitsubishi
widescreen, high definition TV. We urge you to examine this Owner’s Guide to
become familiar with the innovative features and operations this unique television
offers.

The very core of our corporate philosophy is to provide our customers with the
very best. Our development team at Mitsubishi has worked to provide you with
a television that defines “state-of-the-art,” with the capability to meet your needs
now and in the future.

Whether this is your first Mitsubishi electronic product, or an addition to your
Mitsubishi collection, we believe you and your family will continue to enjoy your
Mitsubishi home theater for many years.

Thank you,
Mitsubishi Digital Electronics America, Inc.

Chapter . . .

Television Overview
TV Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Special Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Front Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Remote Control
Overview.. . . . . . .
Battery Installation .
Care.. . . . . . . . . .
Sleep Timer. . . . . .

.
.
.
.

14
15
15
15

TV Back Panel. . . . . . .
Memory Card Reader. .
System Reset Button. .
TV Reset Menu.. . . . . .

.
.
.
.

16
18
20
20

TV Accessories
Please take a moment to review the following
list of items to ensure that you have received
everything.

$"#-&%#4%57 7$3 %7%
"6%*0
57

427

70-

108&3

3. One Digital Audio Cable (sends the audio of digital
channels to a digital audio/video receiver).
46#$"/$&-

%&7*$&

.65&

1"(&

(6*%&

57.&/6

%&7*$&
.&/6

)0.&

7$)*1

*/'0

1*1101

1*1$)

1*1%&7*$&

"6%*0

7*%&0

&9$)

4-&&1

'03."5

3&$

$0//&$5

1"64&

1-":
'''8%

3&83&7

4501

One Four-Headed IR Emitter Cable (allows
NetCommand and TV Guide On Screen® to control
other devices)

5. Product Registration Card (not pictured)
6. Owner’s Guide (not pictured)
7.
1.

Remote Control

AA
AA

2. Two AA Batteries

Chapter 1. Television Overview

Quick Reference Card (not pictured)

8. TV Guide On Screen® Interactive Program Guide
User’s Manual (not pictured)

Special Features
Your new High Definition widescreen television has many special features that make it the perfect center of your home
entertainment system, including:

High Definition DLP™ Display System

Your widescreen Mitsubishi HDTV uses Texas Instruments most advanced Digital Light Processing™ technology for
rear projection televisions. This TV is truly a high-performance multimedia monitor uniquely capable of both stunning
high-definition video images and clear, detailed, high-resolution PC images. Your TV is able to accept video signals
from an antenna or direct cable in standard video scanning rates of 480i, 480p, 720p, 1080i and 1080p. It is also able
to accept, through the HDMI 2 connection, signals with PC resolutions from VGA (640 x 480) through XGA (1024 x 768).
When used with a compatible graphics card and controlling software, this TV is also able to accept the custom PC
resolution of 720p (1280 x 720). To connect a PC to HDMI 2, you need a PC video card with DVI or HDMI output. Next
you need to perform NetCommand setup for the HDMI 2 PC input so that the TV knows to apply the correct PC-signal
processing. All of the compatible video and PC signals will be converted to 1080p for final display; some signals will,
however, add black side bars, top and bottom bars, or both to fill the screen, and some signals will display standard
video overscan.

TV Guide On Screen® Interactive Program Guide System

An eight-day on-screen program guide that can be used with cable, over-the-air and CableCARD™ reception. The
subscription-free guide system lists regular, digital and high-definition programming. This system allows multiple
sorting options and easy program recording. Program listings are downloaded while your TV is turned off, so that you
have current program information available every day. Note that when the system is first set up, it may take up to 24
hours to begin to receive TV program listings. It may take one week to receive all eight days of TV program listings.

Digital Cable Ready (CableCARD™)

Your widescreen Mitsubishi HDTV is “Plug-and-Play” ready. It can descramble a cable provider’s one-way digital
signals with the use of a CableCARD security module. The CableCARD is used in place of a traditional cable box
to access digital cable programming (including high definition). Contact your local cable provider for availability
information and service details.

NetCommand® Home Network Control System

Your widescreen Mitsubishi HDTV offers a new level of networking to combine selected older products with new and
future digital products. NetCommand supports IEEE 1394 connections, Audio Video Control system (AV/C), 5C copy
protection and IR control of selected older products such as VCRs, DVD players, cable boxes or satellite receivers.
NetCommand includes the ability to learn remote control signals directly from many devices, allowing you to customize
the NetCommand system in a way that works best for your viewing

16:9 Widescreen Picture Format

Enjoy a full theatrical experience in the comfort of your home. View pictures as film directors intended them. Digital TV
broadcasts, DVDs and newer video game consoles support this widescreen format.

Memory Card Reader

You can display a slide show of your favorite JPEG pictures or listen to MP3 or WMA audio selections that have been
recorded on compatible memory cards.

Chapter 1. Television Overview

Front Control Panel
The shaded buttons on the front control panel are duplicated on the remote control. The top row of labels shows the
control functions when there are no TV menus displayed on the screen. The bottom row of labels shows the control
functions when the TV menus are displayed on the screen or when a special function has been activated. See “Remote
Control Overview” for further details on the functions of these buttons.

o70-o

o$)o

108&3
-".145"5645*.&3

4:45&.
3&4&5

"%+645

'03."5
&/5&3

Front Control Panel
1. Shaded buttons duplicate buttons on the remote control
4. Status indicator 5. Power/Timer indicator

.&/6

(6*%&
$"/$&-

%&7*$&

Models WD-52628, WD-62628

.&/6

2. System Reset

Model WD-73727

3. Lamp indicator

If the TV does not respond to either the remote control or the front panel controls and/or
does not power off, press the SYSTEM RESET button with a pointed item, such as the end
point of a paperclip. The TV will turn off and the TIMER light will flash quickly for about one
minute. When the TIMER light stops flashing, you may again turn on the TV. The changes
you made the last time the TV was on before you used the SYSTEM RESET button may be
lost. Any changes that you previously saved are not lost.

4:45&.
3&4&5

Front-Panel Indicator Lights
Lamp Indicator
Indicator Color

TV Condition

Additional Information

None (indicator off)

Normal TV on or standby condition.

Normal operation.

Green, rapid blinking TV just powered off and lamp is
cooling.

Begins to blink 30 seconds after turning off TV. TV
can be turned on before it begins to blink or after the
blinking stops, but not while the indicator is blinking.
Normal operation.

Yellow, steady

Lamp nearing end of useful life.

This is a recommendation to have a new lamp ready
before the current lamp stops illuminating. See
Appendix H for ordering information.

Yellow, blinking

TV will not operate until lamp access door is secure.
See Appendix H for installation information.

Red, steady

Lamp access door is open or not
secure.

2. No lamp installed.

TV will not operate without a lamp. See Appendix H
for installation information.

Lamp no longer illuminates and has
reached the end of the lamp life.

Replace the lamp. The TV will not operate when
the lamp no longer illuminates. See Appendix H for
installation information.

Chapter 1. Television Overview

Front Control Panel, continued

Status Indicator
Indicator Color

TV Condition

Additional Information

None (indicator off)

Normal TV on or standby condition.

Normal operation.

Yellow, steady

Room temperature is too high.

TV will not operate when the ambient room
temperature is too high. Turn off the TV and wait until
the room temperature drops.

Red, either steady or TV may require service.
blinking

Turn off the TV and unplug the set from the AC power
source. Wait one minute and then plug the set back
in.
If the LED is still on, contact your dealer or a
Mitsubishi Authorized Service Center. See
www.mitsubishi-tv.com or call 1-800-332-2119 to
receive Authorized Service Center information.

Power/Timer Indicator
Indicator Color

TV Condition

Additional Information

None (indicator off)

TV is powered OFF.

Normal operation.

Green, steady

TV is powered ON.

Normal operation.

Green, rapid blinking 1.

Green, slow blinking

TV just plugged into AC outlet.

Wait until blinking stops before turning on
(approximately 1 minute). Normal operation.

2. AC just restored after power
failure.

Wait until blinking stops before turning on
(approximately 1 minute). Normal operation.

3. TV Rebooting after System Reset
used.

Wait until blinking stops before turning on
(approximately 1-2 minutes). Normal operation.

4. TV Rebooting after power
fluctuation or receiving abnormal
digital signals from digital channel,
CableCARD™, or digital device.

Wait until blinking stops before turning on
(approximately 1 minute). Normal operation.

5. You have begun the procedure
to update software from an
authorized flash memory device.

For detailed information, see the instructions
that accompany the authorized software update.
Important: Do not use non-authorized software at
any time.

TV powered off and automatic-on
timer is set.

Normal operation. TV can be turned on at any time.

A/V Reset

There may be times when you wish to reset the A/V (Audio and Video) settings back to the factory defaults. To return
all the settings at once, press GUIDE and FORMAT on the front panel at the same time. To reset the defaults for
individual devices, use the A/V Memory Reset selection on the Audio/Video menu.

Chapter 1. Television Overview

Remote Control
Overview

Figure 1, following page

2.
3.
4.

7.
8.
9.

10.

11.
12.
13.
14.
15.

Slide Switch: Selects the A/V product to be
controlled by the remote control. Select TV for
NetCommand® device control.
Numbers: Individually select channels or enter
information into menus.
SQV (SuperQuickView™): Scans through
memorized lists of favorite channels.
CH(ANNEL)/PAGE: Scans up or down through
memorized channels. Pages up and down through
screens when used with TV Guide On Screen®,
ChannelView™, a satellite receiver, some cable boxes,
memory card playlists and JPEG thumbnails. Pages
up and down through DVD chapters.
DEVICE: Displays the Device Selection menu in
which you can select the device to view (ANT-1 and
ANT-2, or devices connected to the TV’s inputs,
including IEEE 1394 devices).
to navigate menus,
ADJUST: Press
change settings, and move the PIP on-screen
location. Operates many NetCommand® functions.
Navigate TV Guide On Screen® and change settings.
TV MENU: Displays the
on-screen menu
system.
ENTER: Selects a channel number or menu item.
DEVICE MENU: Displays the menu for devices
connected to the TV, including CableCARD™. For
VCR or DVDs, the first press displays the transport
menu, the second press displays the VCR or DVD
menu. Displays and removes options menus for TV
Guide On Screen. Opens the Media Dialog Box for
memory cards.
INFO: Press to display an on-screen summary of the
current device used and any broadcast information
available (including current V-Chip information). See
Appendix B for details on the on-screen display.
While in TV Guide On Screen, press repeatedly to
cycle through the available info box sizes.
V-CHIP: Turns the V-Chip Lock on or off.
PIP/POP: Turns on PIP and cycles through PIP and
POP display choices.
PIP CH: Scrolls up or down through memorized
channels for PIP
PIP DEVICE: Displays PIP Selection menu to select
the PIP or POP image source device
REC (Record): Displays the Record menu for
setting up recordings. Records with a VCR, sets up
recordings for DVCR, IEEE 1394 devices, or while in

Chapter 1. Television Overview

ChannelView. Starts a recording when the Listings
screen for TV Guide On Screen is displayed.
16. REW/REV: Rewinds a VCR. Reverses scan with a
DVD, A/V Disc, or memory card file.
17. POWER: Turns power on and off for the TV and
other A/V products.
18. QV (QuickView™): Switches between the current
channel and last channel viewed.
19. SUB/CANCEL: When entering digital channel
numbers, adds separator between main and
sub-channel numbers. Clears SQV and some menu
entries, and cancels recordings.
20. VOLUME: Changes sound level.
21. MUTE: Turns sound on or off.
22. GUIDE: Displays or removes TV Guide On Screen
or ChannelView for ANT-1 and 2. Displays Track List
for A/V Disc. Displays program guide for satellite
receiver and cable boxes, or DVD Disc menu.
Displays thumbnails or playlists for memory card files.
23. Light: Located on the right side of the remote
control, this feature illuminates buttons or labels.
24. HOME: Exits TV on-screen menus and the TV Guide
On Screen system and returns to TV viewing.
25. AUDIO: Selects individual audio settings for
adjustment.
26. VIDEO: Selects individual video settings for
adjustment.
27. EXCH: Exchanges PIP or POP and main TV picture.
28. SLEEP: Sets the TV to turn off within 2 hours. See
the next page for setup instructions.
29 CONNECT: Initiates IEEE 1394 peer-to-peer
connections.
30. FORMAT: Changes the shape and size of the main
TV picture.
31. PAUSE: Pauses a live TV picture when no PIP or
POP image is displayed. When PIP image is visible,
pauses that image. Pauses a VCR, DVD, A/V Disc, or
memory card file.
32. PLAY: Plays a VCR, DVD, A/V Disc, or memory card
file.
33. FF/FWD: Fast forward a VCR or memory card file, or
fast play a DVD or A/V disc.
34. STOP: Stops play of a VCR, DVD, A/V Disc, or
memory card file.

Remote Control, continued

3
4
5
6
7
8
9
10
11
12

108&3

46#$"/$&-

427

%&7*$&

70-

Figure 2. Operation: Installing the Batteries

.65&

1"(&

(6*%&

57.&/6

23
24

%&7*$&
.&/6

)0.&

*/'0

1*1101

1*1$)

7$)*1

""BMLBMJOF
CBUUFSJFT

1*1%&7*$&

$"#-&%#4%57 7$3 %7%
"6%*0
57

2. Load the batteries, making sure the polarities (+) and
(-) are correct. For best results, insert the negative (-)
side first.

"6%*0

7*%&0

&9$)

4-&&1

'03."5

3&$

$0//&$5

1"64&

1-":
'''8%

3&83&7

28
29
30
31
32

4501

33
16

Figure 1. Remote Control Overview

Battery Installation
Figure 2

Care

For Best Results from the Remote Control:
•
•
•
•
•
•
•
•

Be within 20 feet of the equipment.
Do not press two or more buttons at the same time
unless instructed.
Do not allow unit to get wet or become heated.
Avoid dropping on hard surfaces.
Do not use harsh chemicals to clean. Use only a soft,
lightly moistened cloth.
Do not mix new and old batteries.
Do not heat, take apart, or throw batteries into fire.
Use only AA alkaline batteries.
Hint: If the remote is in the TV layer and does not
function, press POWER and 9, 3, 5 to reset the
remote.

Sleep Timer

Setting the Sleep Timer:
1. Press SLEEP on the remote control.
2. Each additional press of SLEEP increases the time
displayed by 30 minutes up until the maximum value
of 120 minutes.
3. After five seconds of inactivity, the message will
disappear.
4. Press SLEEP to view the time remaining before the
timer turns the TV off.

Installing the Batteries:

Cancelling the Sleep Timer:

1. Press SLEEP to display the on-screen message.
2. Press SLEEP repeatedly until OFF is displayed.

Remove the remote control’s back cover by gently
pressing the ribbed tab in the direction of the arrow
and sliding off the cover.

Note: After five seconds of inactivity, the message box disappears.

Chapter 1. Television Overview

TV Back Panel
3

COMPONENT

INPUT
1

YPbPr (480i/480p/720p/1080i)
2

INPUT

S-VIDEO

VIDEO

AUDIOLEFT/
(MONO)

AUDIORIGHT

OUTPUT

DVI
Analog Audio
1

AUDIO
OUTPUT

VIDEO

AUDIOLEFT/
(MONO)
AUDIORIGHT

MONITORLINK™/HDMI
VIDEO 480i/480p/720p/1080i
AUDIO PCM LINEAR

IR EMITTER
Net Command¸

1
ANT 1 / MAIN

10
ANT 2 / AUX

DIGITAL
AUDIO
OUTPUT

1. Antenna (ANT-1 MAIN, ANT-2 AUX)

ANT-1 MAIN and ANT-2 AUX can each receive both
digital and analog over-the-air channels from a VHF/UHF
antenna or non-scrambled digital/analog cable source.

Your primary viewing signal source should be connected
to ANT-1 MAIN. ANT-1 MAIN must be used to view
premium subscription cable TV service authorized by the
CableCARD™ access card. The CableCARD access card
is provided by your local cable company. ANT-2 AUX can
receive over-the-air or non-scrambled cable signals.

2. IR EMITTER NetCommand®

IR Emitters connected to these jacks are used by the
NetCommand system of the TV to control external analog
devices such as cable boxes, VCRs, DVDs, satellite
receivers and audio receivers. This system is also
coordinated with the TV Guide On Screen® system for
the control of cable boxes and to activate the record
feature of your VCR. Either connection can be used for
NetCommand functions.

3. INPUT 1 and 2

(Audio/Video 1 and 2)

Inputs 1 and 2 can be used for the connection of a VCR,
Super VHS (S-VHS) VCR, DVD player, standard satellite
receiver or other A/V device to the TV. Please note that
if S-VIDEO and VIDEO are available for the input, you

PC - 60Hz
VGA, W-VGA,
SVGA, W-SVGA,
XGA, 1280 X 720

' ,INK ¸

DTV/CABLE/
VHF/UHF

RECORD
OUTPUT

Chapter 1. Television Overview

9
CableCARD™ USE WITH ANT 1 CARD TOP

IEEE 1394
INPUT/
OUTPUT

must choose to connect only one. They cannot both be
connected at the same time.

4. COMPONENT 1, 2, and 3 Inputs

YPbPr (480i/480p/720p/1080i)

These inputs can be used for the connection of devices with
component video outputs, such as a DVD player, external
HDTV receiver, or compatible video game system. Please
see Appendix A for signal compatibility.

5. DVI Analog Audio

Unlike HDMI, DVI does not carry audio information on the
same cable. Use these analog stereo audio inputs when
using the HDMI input with a device that outputs DVI instead
of HDMI, such as DVI output from a personal computer.

6. AUDIO OUTPUT, RECORD OUTPUT

AUDIO OUTPUT sends analog audio of the program
currently shown on the screen to an A/V surround sound
receiver or stereo system. Digital audio from digital
channels, FireWire® (DTV Link/IEEE 1394) devices and
HDMI devices is converted to analog audio by the TV. If
you do not have a digital A/V receiver, this should be the
only audio connection between the TV and your analog
A/V receiver or stereo system.
RECORD OUTPUT sends analog audio and video to
a VCR for recording purposes. These signals may not
be the same as those of the program that is currently

TV Back Panel, continued

being shown on screen. Signals from digital channels
and FireWire (IEEE 1394) devices are converted to analog
signals. There is no video signal when copy restrictions
are in effect. Audio alone is output when a Component
input or the HDMI input is selected for recording.

7. HDMI™ 1 and 2

The HDMI (High Definition Multimedia Interface) supports
uncompressed standard and high-definition digital video
formats and PCM digital audio format.
Use these inputs to connect to EIA/CEA-861 compliant
devices such as a high-definition receiver or DVD player.
These inputs support 480i, 480p, 720p and 1080i video
formats.
These inputs can also be used as a DVI connection with
separate analog audio inputs. An optional HDMI-to-DVI
adaptor or cable is necessary to make this connection
and may be available from your local electronics retailer.
When using the optional HDMI-to-DVI adapter, the DVI
analog audio inputs on your TV allow you to receive left
and right audio from your DVI device.
This input is HDCP (High-Bandwidth Digital Copy
Protection) compliant.
HDMI 2
HDMI 2 also allows the TV to display DVI or HDMI output
from a PC. To view PC video on the TV, you must activate
the PC option in NetCommand. You can do this during
initial NetCommand setup by selecting the PC option
in the Device Setup screen. To do this at any time
afterwards, use the NetCommand Add function.
To listen to audio from a PC when using PC DVI output,
you must connect the PC audio output to the TV’s DVI
Analog Audio 2, located above the HDMI 2 input.

8. DTV Link™/IEEE 1394
These jacks allow the TV to connect to external IEEE
1394 digital products by means of a single cable. Two
jacks are provided for this purpose, which allow for a high
degree of flexibility for connecting your NetCommand
controlled system. Detailed information regarding
IEEE 1394 connection requirements is in Chapter 2,
“Connecting.”

9. CableCARD™ Slot

The CableCARD access card from your cable TV service
provider is inserted into this slot. The top of the card
should face in the direction indicated by CARD TOP .
CableCARD is a nationwide standard system that allows
your local cable TV provider to supply you with an
access card customized to your account. This card
allows the TV to receive, decode and unscramble the
premium digital channels included in your cable TV
subscription without the use of a cable box. See page
23 for additional CableCARD information and activation
instructions.
If your cable company is not currently offering
CableCARD access cards, you will need to use a
cable box provided and authorized by your local cable
company to view scrambled channels.

10. Digital Audio Output

This output sends Dolby® Digital or PCM digital audio to
your digital A/V surround sound receiver. Analog audio
from analog channels and devices is converted by the
TV to PCM digital audio. In most cases, this should be
the only audio connection between the TV and your A/V
receiver. If you have MP3 audio from memory cards,
however, you need to connect the TV’s analog AUDIO
OUTPUT (left and right) to your A/V receiver.

Chapter 1. Television Overview

Memory Card Reader and Front-Panel Inputs

Memory Card Reader

Models WD-52628, WD-62628

Figure 3

The memory card reader has four card slots that allow
the display of JPEG pictures from many digital cameras
and allow you to listen to MP3 or WMA audio files
recorded from computers or other digital recording
devices.
The card slots are designed for the specific types of
cards listed below. Other cards or objects should not
be inserted into the slots as this may damage the TV.
See the discussion of memory cards in chapter 6 for
details about JPEG, MP3 and WMA file types that are
compatible with the TV.
Card Compatibility
Slot

Card Types

CARD 1
CARD 2
CARD 3

SmartMedia™
MultiMediaCard™
Secure Digital (SD)
CompactFlash®
(Types I and II)

Memory Card
Reader

Microdrive®
CARD 4

Memory Stick PRO™
Memory Stick™

$"3%4NBSU.FEJB5.

$"3% .VMUJNFEJB$BSE5.

4%$BSE

3
%*%#4

Input 3 and IEEE
1394 Input/Output

$"3% $PNQBDU'MBTI¥

.JDSP%SJWF¥

$"3%130

Figure 3. Memory Card Reader

IMPORTANT
Portions of the advanced circuitry of this TV must continue to operate even when the TV is turned
off. Some of these circuits therefore need to be cooled at all times. A low-power standby fan may
be heard in a quiet environment. This is normal operation.

Chapter 1. Television Overview

Memory Card Reader and Front-Panel Inputs

Input 3 and IEEE 1394 Input/Output
Figure 4

These jacks allow for convenient connection of audio/
video devices to the front of the TV.
Note that if you connect to the S-VIDEO terminal, the
VIDEO terminal is deactivated. The VIDEO terminal is
active only when there is no S-Video connection.
Use the IEEE 1394 input/output to connect IEEE 1394
devices, such as some camcorders. This connection
works the same as the rear IEEE 1394 connections.
Please refer to the NetCommand® information (Chapter
3) for details.

3 6)$%/

6)$%/

!5$)/

)%%%

Figure 4. Input 3 and IEEE 1394 input/output on front panel

Model WD-73727

$"3%4NBSU.FEJB5.

%*%#4

$"3% $PNQBDU'MBTI¥

.JDSP%SJWF¥

$"3% .VMUJNFEJB$BSE

4%$BSE

$"3%130

Memory Card
Reader

Input 3 and IEEE 1394
Input/Output

Chapter 1. Television Overview

Additional Information

System Reset Button

TV Reset Menu

If the TV doesn’t respond to either the remote control
or the front panel controls or will not power off, press
the SYSTEM RESET button on the front panel with a
pointed item such as the point of a ball point pen or
end tip of a paperclip.

The TV will turn off and the green LED will flash
quickly for about one minute. When the green LED
stops flashing, you may turn on the TV again. The
changes you made while the TV was most recently
on, before you used the SYSTEM RESET button, may
be lost; the changes you made previously, however,
are not lost. Only those changes since the last power
on may be lost when the system reset button is
pressed. All other settings are retained.

Read on-screen warnings before
proceeding, as some user data or
settings may be erased.
Press TV MENU and then 1, 2, 3 to see the
RESET SERVICE MENU to reset the TV.

2. Select Reset System Defaults (CAUTION: All
settings, except V-Chip, will be reset to the
original factory defaults).

Demo Mode

This TV has a demo mode for use in retail stores. To turn the demo mode On/Off, press the following buttons in
sequence:
MENU, 0, QV, 0

IMPORTANT
Do not attempt to update the software of this TV with software or cards that are not provided
by or authorized by Mitsubishi Digital Electronics America, Inc. Non-authorized software may
damage the TV and will not be covered by the warranty.

Chapter 1. Television Overview

Chapter . . .

Connecting
External Devices and NetCommand® Setup. . . . . . . . . . . . . .
Using a CableCARD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wall Outlet Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standard Cable Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Antenna with a Single Lead. . . . . . . . . . . . . . . . . . . . . . . . . .
Antennas with Separate UHF and VHF Leads. . . . . . . . . . . . .
VCR to an Antenna or Wall Outlet Cable (Audio & Video).. . . . .
VCR to a Cable Box (Audio & Video). . . . . . . . . . . . . . . . . . . .
A/V Receiver (Stereo System). . . . . . . . . . . . . . . . . . . . . . . .
Satellite Receiver or Other Device with S-Video.. . . . . . . . . . .
DVD Player with Component Video.. . . . . . . . . . . . . . . . . . . .
DVI Device.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HDTV Cable Box or Satellite Receiver with Component Video ..
HDMI Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Computer with an HDMI Monitor Output.. . . . . . . . . . . . . . . .
Computer with a DVI Monitor Output. . . . . . . . . . . . . . . . . . .
IR Emitter NetCommand®.. . . . . . . . . . . . . . . . . . . . . . . . . .
Compatible IEEE 1394 Devices.. . . . . . . . . . . . . . . . . . . . . . .
Helpful Hints for NetCommand Connections. . . . . . . . . . . . . .

.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.

22
23
24
24
25
25
26
27
28
28
29
29
30
30
31
31
32
33
35

Connecting External Devices and NetCommand® Setup
NetCommand is able to control many current audio and video devices by sending remote control signals from the TV to
each device through IR emitters. Additionally, it can learn the remote control signals used by most audio video devices
not already in the TV’s memory. NetCommand can automatically switch the TV and compatible or learned Audio/Video
(A/V) Receivers to the correct input used with each device. It is important that the inputs on the TV and A/V receiver
back panels match the NetCommand setup that is displayed on screen.
To simplify the installation of NetCommand, there is a step-by-step on-screen NetCommand Setup procedure in this
chapter, which details the type and brands of devices you are connecting to the TV. The NetCommand Setup also
assigns preset TV and A/V receiver inputs for each device. You should connect each device to the TV input (both audio
and video) and to the A/V receiver (audio) as shown in the figure below. If you connect devices to inputs other than the
ones shown as presets, you must change the NetCommand setup accordingly. See the Edit NetCommand information
starting on page 45.

Device to be
connected

video and stereo
audio cables

stereo and/or digital
audio cables

*3&NJUUFST

TV
stereo and/or digital audio cables

AV
Receiver

The following charts show which preset inputs you should use on the TV and A/V receiver.
Chart 1 shows the default TV inputs existing in NetCommand.
Chart 2 shows the A/V receiver inputs used by A/V receiver models already known by NetCommand.

Chart 1
NetCommand Default Device Audio and Video Outputs to TV Inputs
Cable for CableCARD™ Service

ANT-1

Antenna/Cable (digital/analog)

ANT-1 if primary viewing source,
ANT-2 if secondary viewing source

Cable box

COMPONENT-1

VCR

Input-1

Satellite Receiver (SAT)

Input-2

Camcorder

Input-3 (on front panel)

DVD Player

COMPONENT-2

HDMI-2

$IBSU

.JUTVCJTIJ.JUTVCJTIJ#PTF%FOPO*OUFHSB,FOXPPE.BSBOU[1JPOFFS1JPOFFS3PUFM4POZ:BNBIB:BNBIB
.PEFM
.PEFM
.PEFM
.PEFM
.PEFM
.PEFM
.PEFM
.PEFM
.PEFM
.PEFM
.PEFM
.PEFM
.PEFM
.73 .73 -JGFTUZMF ¥ "73 %53 73 43 749% 74959 349 453%& 397 397
.73
.73

%FWJDF"VEJP0VUQVUUP
7$3
7$3
4BUFMMJUF3FDFJWFS
"VY
%7%1MBZFS
%7%
57.POJUPS0VUQVU
57
%JHJUBM"VEJP

"73FDFJWFS*OQVUTCZ/BNF
7$3
7$3
7$3
$BCMF%#4
"69
$%
%7%
CVJMUJO
%7%7%1
57
57
57%#4

7JEFP
7JEFP
%7%
7JEFP

7JEFP
7JEFP
7JEFP
7JEFP

7$3
%44
%7%
57

7$35BQF 7$3%73
$%
4"5
-%4"5
%7%-%
%7%57
57

7JEFP
7JEFP
7JEFP
7JEFP

7JEFP
57%#4
5"1&.%
%7%-%

7$3
57%#4
$%
%7%-%

7$3
%57-%
%7%
$#-4"5

After using NetCommand Setup, you may go to the NetCommand menu at any time to change the inputs you used for
connecting each device, custom name devices, add devices not included in the presets above or delete devices no
longer used. See Edit NetCommand. See Helpful Hints at the end of this chapter for additional information on device
setup.

Chapter 2. Connecting

Using a CableCARD

After inserting a CableCARD into the TV back panel
CableCARD slot and powering On the TV, the initialization
process begins. An initial screen will automatically
display for a few minutes, with information that your
Cable Provider will need in order to start service. Please
write down this information before calling your cable
provider.

Please call XYZ Cable
at xxx-xxx-xxxx to
activate cable service.
They will need these numbers:
Host ID X-XXX-XXX-XXX-XXX
CableCARDTM ID: X-XXX-XXX-XXX-XXX
See owner's manual for
further information

An example of an initial screen is shown here. Your
screen will display specific information from your cable
provider and may not look like this screen.
If you were unable to record the information, you can
press TV MENU on the remote and then enter the
number 999 and the screen will re-display. You can
also press DEVICE MENU when the CableCARD is the
selected source and you will be able to select the startup
application.

IMPORTANT

CableCARD Technology

CableCARD is a nationwide system standard that allows
your local cable TV provider to supply you with an access
card customized to your account. This card allows your
TV to receive, decode and unscramble the premium
digital channels included in your cable TV subscription
without the use of a cable box. It also allows your
cable provider to automatically update and change your
subscription. When you move to a new cable provider’s
area, you simply return the CableCARD to the original
cable provider and get a new card from your new cable
provider.
Please note that CableCARD is a new technology and
your local cable provider may not currently be offering
this service. As time passes, this system will become
broadly supported by most cable providers.
The CableCARD system is “unidirectional” which means
your cable provider can send updates to the access
card and TV, however, the TV cannot send back signals
such as requests for Video-On-Demand or Pay-per-View
programs by remote control.
Digital cable channels authorized by the CableCARD
will be available on the Firewire® IEEE 1394 network
and can be shared by other products on the network.
Some digital channels or programs may not be copied
or recorded because of copy restriction limits set by the
content owners or copyright holders.
The digital television is capable of receiving analog
basic, digital basic, and digital premium cable
television programming by direct connection to a
cable system providing such programming. A security
card (CableCARD) provided by your cable operator is
required to view encrypted digital programming. Certain
advanced and interactive digital cable services, such as
video-on-demand, a cable operator’s enhanced program
guide, and data-enhanced television services, may
require the use of a set-top box. For more information,
call your local cable operator.
Please see page 17 for instructions on how to insert the
CableCARD.

To use a CableCARD, the primary incoming
cable must be connected to ANT-1 MAIN.

Chapter 2. Connecting

Connecting a Wall Outlet Cable or Cable Box

Wall Outlet Cable

Standard Cable Box

(can be used with a CableCARD™)
Figure 1

It is very important to connect the incoming cable
for your primary viewing source to ANT-1, especially
for CableCARD™ use and to download TV Guide On
Screen® listings.
1.

Connect the primary incoming coaxial lead cable to
ANT 1/MAIN on the TV back panel.

2. For an optional secondary antenna source, connect
an antenna (or cable) to ANT 2/AUX.
3. If you have subscribed to a CableCARD™ service, the
CableCARD can now be inserted into the CableCARD
SLOT. Using a Phillips screwdriver, remove the
CableCARD cover screws. Insert the CableCARD,
then replace the cover and screws. The top of the
card should face in the direction the CARD TOP
arrow indicates.
Additional CableCARD information is on page 23.
Detailed TV Guide On Screen information is in the
separate User’s Manual.

DTV/CABLE/
VHF/UHF

ANT 1 / MAIN

5P"/5."*/

ANT 2 / AUX

DIGITAL
AUDIO
OUTPUT

(cable box, other than an HDTV cable box; this setup
allows two-channel PIP)
Figure 2
3 coaxial cables and one two-way RF splitter are required.
These are not included with the TV.

Note: See page 30 to connect an HDTV cable box.
1. Connect the incoming cable to IN on an RF splitter.
2. Connect one coaxial cable from OUT on the RF
splitter to ANT-1 MAIN on the TV back panel.
3. Connect one coaxial cable from OUT on the RF
splitter to IN on the standard cable box.
4. Connect one coaxial cable from OUT on the cable
box to ANT-2 AUX on the TV back panel.
5. After the cable box is connected to ANT-2 AUX as
shown, use the NetCommand menu Change option
to change the default connection for the cable box,
go to the RF Connection for Cable screen and do the
following:
a. Check the RF check box.
b. For antenna, select ANT-2.
c. For Channel, select the channel to which the TV
must be tuned for your cable box. The default
channel is 3.
When this setup is complete, you can use the TV remote
control to change channels on the cable box.

CableCARD™ USE WITH ANT 1 CARD TOP

5P"/5"69

57CBDLQBOFM
TFDUJPO
DTV/CABLE/
VHF/UHF

57CBDL
QBOFM
TFDUJPO

$BCMF$"3%5.4-05
DPWFSSFNPWFE

ANT 2 / AUX

DIGITAL
AUDIO
OUTPUT

CableCARD™ USE WITH ANT 1 CARD TOP

5P"/5."*/

5P"/5"69

*ODPNJOH
$BCMF

065

Figure 1. Wall Outlet Cable

065

0QUJPOBM4FDPOEBSZ
"OUFOOBPS$BCMF
5808":41-*55&3

1SJNBSZ8BMM
0VUMFU$BCMF

ANT 1 / MAIN

3'4QMJUUFS
$BCMF#PYCBDL
QBOFMTFDUJPO

065

Figure 2. Connecting a Cable Box

IMPORTANT
Additional connection cables are
not provided with the TV. They are
available at most electronics stores.

Chapter 2. Connecting

Note: To use a cable box connected to ANT‑2 as shown
above, you must make the noted NetCommand changes.
The changes are required to change the NetCommand
cable-box default connection (Component-1) to the
actual connection (ANT-2).

Connecting an Antenna with a Single Lead or Antennas with
Separate UHF and VHF Leads
Antenna with a Single Lead

Antennas with Separate UHF and VHF
Leads

(not for use with CableCARD™)
Figure 3

Figure 4
A UHF/VHF combiner is required. This is not included with the
TV, but is available at most electronics stores.

For antennas with flat twin leads
A 300-ohm-to-75-ohm transformer is required. This is not
included with the TV, but is available at most electronics stores.

For an antenna with flat twin leads, connect the
300-ohm twin leads to the 300-ohm-to-75-ohm
transformer.

Connect the UHF and VHF antenna leads to the UHF/
VHF combiner.

2. Push the combiner onto ANT-1 MAIN on the TV back
panel.

2. Push the 75-ohm side of the transformer onto ANT-1
MAIN on the TV back panel.

7)'"OUFOOB
$IBOOFMT

For cable or antenna with coaxial lead
Connect the coaxial lead directly to ANT-1 MAIN on
the TV back panel.

6)'"OUFOOB
$IBOOFMT

'MBU5XJO-FBE

'MBU5XJO-FBE
&YUFSOBM
"OUFOOB
PS$BCMF

57CBDLQBOFMTFDUJPO

57CBDLQBOFMTFDUJPO
0IN
'MBU5XJO
-FBE

0IN
$PBYJBM
$BCMF

VIDEO

0INUP
0IN
$PNCJOFS
6)'

DTV/CABLE/
VHF/UHF

ANT 2 / AUX

AUDIORIGHT

' ,INK ¸
IR EMITTER
Net Command¸

DIGITAL
AUDIO
OUTPUT

#BDL
7JFX

Figure 3. Connecting a Single Antenna

AUDIOLEFT/
(MONO)

7)'

ANT 1 / MAIN

YPbPr (480i/480p/720p
2

S-VIDEO

IR EMITTER
Net Command¸

0QUJPOBM0INUP0IN
.BUDIJOH5SBOTGPSNFS

COMPONENT

INPUT
1

4JEF
7JFX
DTV/CABLE/
VHF/UHF

4O !.4 -!).

ANT 1 / MAIN

ANT 2 / AUX

Figure 4. Connecting separate UHF and VHF Antennas

Mitsubishi strongly recommends you avoid using
antennas with flat twin leads. Flat twin lead
antenna wires are subject to interference which
may adversely affect the performance of the TV.
We recommend using coaxial antenna cable.

Chapter 2. Connecting

DIGITAL
AUDIO
OUTPUT

Connecting a VCR to an Antenna or Wall Outlet Cable
Connecting VCR Audio and Video to the TV

VCR to an Antenna or Wall Outlet
Cable (Audio & Video)

Figure 5
A two-way RF splitter, 3 coaxial cables, right and left audio
cables, and an S-video or video cable are required. These are
not included with the TV but are available at most electronics
stores.

5. Connect either an S-Video or Video cable from
VIDEO OUT on the VCR back panel to INPUT-1
VIDEO on the TV back panel. Only one type of
video cable should be connected. S-Video is
recommended, if available.

Connect the incoming cable or Antenna to IN on the
RF splitter.

6. For NetCommand®-controlled recordings (including
TV Guide On Screen), connect a set of audio cables
from AUDIO IN on the VCR back panel to RECORD
OUTPUT/AUDIO-LEFT and AUDIO-RIGHT on the TV
back panel. The red cable connects to the R (right)
channel and the white cable connects to the L (left)
channel.

2. Connect one coaxial cable from OUT on the RF
splitter to ANTENNA IN on the VCR back panel.
3. Connect one coaxial cable from OUT on the RF
splitter to ANT-1 MAIN on the TV back panel. This
connection also allows you to use the TV Guide On
Screen® feature.

To use the TV speakers with the VCR, connect a set of
audio cables from AUDIO OUT on the VCR back panel
to INPUT-1 AUDIO-LEFT (MONO) and AUDIO-RIGHT
on the TV back panel. The red cable connects to
the R (right) channel and the white cable connects to
the L (left) channel. If your VCR is mono (non-stereo),
connect only the white (left) cable.

Complete the NetCommand controlled recordings
connections by connecting a Video cable from
VIDEO IN on the VCR back panel to RECORD
OUTPUT/VIDEO on the TV back panel.

065

5808":41-*55&3

*ODPNJOH
$BCMF
3'4QMJUUFS

*GZPVS7$3IBTB
WJEFPDIBOOFMPS3'
0/0''TXJUDI TFUJU
UP0''

)46

7$3CBDLQBOFM

"UUBDIPOMZPOFDBCMFUZQF
4WJEFPSFDPNNFOEFEJG
BWBJMBCMF

COMPONENT

INPUT
1

YPbPr (480i/480p/720p/1080i)
2

INPUT

VIDEO

AUDIOLEFT/
(MONO)

AUDIORIGHT

OUTPUT

DVI
Analog Audio

S-VIDEO

AUDIO
OUTPUT

RECORD
OUTPUT

VIDEO

AUDIOLEFT/
(MONO)
AUDIORIGHT

MONITORLINK™/HDMI
VIDEO 480i/480p/720p/1080i
AUDIO PCM LINEAR
1

PC - 60Hz
VGA, W-VGA,
SVGA, W-SVGA,
XGA, 1280 X 720

' ,INK ¸
IR EMITTER
Net Command¸

DTV/CABLE/
VHF/UHF

ANT 1 / MAIN

ANT 2 / AUX

DIGITAL
AUDIO
OUTPUT

CableCARD™ USE WITH ANT 1 CARD TOP
IEEE 1394
INPUT/
OUTPUT

Figure 5. Connecting a VCR to an Antenna or Wall Outlet Cable

Chapter 2. Connecting

46 "ACK
0ANEL

Note:
NetCommand®
will assume your
VCR is connected
to inputs as shown
on this page. If
you use any other
inputs for your VCR
or add a second
VCR, this change
must match in
the NetCommand
system. See Edit
NetCommand... in
Chapter 3 for more
information.

Connecting a VCR to a Cable Box (Audio & Video)

VCR to a Cable Box (Audio & Video)

connects to the L (left) channel. If your VCR is mono
(non-stereo), connect only the white (left) cable.

Figure 6
A two-way RF splitter, 4 coaxial cables, right and left audio
cables and an S-Video or Video cable are required. These are
not included with the TV but are available at most electronics
stores.

Connect the incoming cable to IN on the RF splitter.

2. Connect one coaxial cable from OUT on the RF
splitter to ANTENNA IN on the cable box back panel.

8. For NetCommand®-controlled recordings (including
TV Guide On Screen)
a. Connect a set of audio cables from AUDIO IN
on the VCR back panel to RECORD OUTPUT/
AUDIO-LEFT (MONO) and AUDIO-RIGHT on the
TV back panel. The red cable connects to the R
(right) channel and the white cable connects to
the L (left) channel.
b. Connect a video cable from VIDEO IN on the VCR
back panel to RECORD OUTPUT/VIDEO on the
TV back panel.

3. Connect one coaxial cable from OUT on the RF
splitter to ANT-1 MAIN on the TV back panel. This
connection also allows you to use the TV Guide On
Screen® feature.
4.

Connect either an S-Video or composite video cable
from VIDEO OUT on the VCR back panel to INPUT 1
VIDEO on the TV back panel. Connect only one type
of video cable. S-Video is recommended, if available.

Connect one coaxial cable from OUT on the cable
box to ANTENNA IN on the VCR back panel.

5. Connect one coaxial cable from ANTENNA OUT on
the VCR back panel to ANT-2 AUX on the TV back
panel (optional).

Note: With this connection configuration, it is
possible to view live cable programs through the VCR.
For best picture quality, however, always view live
cable programs directly from the cable box instead of
the VCR.

6. To use the TV speakers with the VCR, connect a
set of audio cables from AUDIO OUT on the VCR
back panel to INPUT-1 AUDIO-LEFT (MONO) and
AUDIO-RIGHT on the TV back panel. The red cable
connects to the R (right) channel and the white cable

7$3CBDLQBOFM

*GZPVS7$3IBTB
WJEFPDIBOOFMPS3'
0/0''TXJUDI TFUJU
UP0''

)46

"UUBDIPOMZPOFWJEFP
DBCMFUZQF TUFQ
4WJEFPSFDPNNFOEFE
JGBWBJMBCMF

COMPONENT

INPUT
1

YPbPr (480i/480p/720p/1080i)
2

INPUT

AUDIORIGHT

AUDIO
OUTPUT

RECORD
OUTPUT

VIDEO

AUDIOLEFT/
(MONO)
AUDIORIGHT

MONITORLINK™/HDMI
VIDEO 480i/480p/720p/1080i
AUDIO PCM LINEAR

065

Pr
AUDIOLEFT/
(MONO)

PC - 60Hz
VGA, W-VGA,
SVGA, W-SVGA,
XGA, 1280 X 720

' ,INK ¸
IR EMITTER
Net Command¸

065

*ODPNJOH
$BCMF

5808":41-*55&3

VIDEO

AUDIOLEFT/
(MONO)

OUTPUT

DVI
Analog Audio

3'4QMJUUFS

S-VIDEO

DTV/CABLE/
VHF/UHF

065

$BCMF#PY
CBDLQBOFMTFDUJPO

ANT 1 / MAIN

ANT 2 / AUX

DIGITAL
AUDIO
OUTPUT

CableCARD™ USE WITH ANT 1 CARD TOP
IEEE 1394
INPUT/
OUTPUT

Note: NetCommand®
will assume your VCR
is connected to inputs
as shown on this page.
If you use any other
inputs for your VCR or
add a second VCR, this
change must match
in the NetCommand
system. See Edit
NetCommand... in
Chapter 3 for more
information.

Figure 6. Connecting a VCR to a Cable Box

Chapter 2. Connecting

Connecting an A/V Receiver (Stereo System)
Connecting a Satellite Receiver or Other Device with S -Video
A/V Receiver (Stereo System)

Figure 7
Most setups require either a digital audio cable or stereo audio
cables. In some circumstances, you may need to connect both
digital audio and stereo audio. A digital audio cable is provided
with the TV. Stereo audio cables are not included.

A. To connect an analog A/V receiver:
Connect a set of stereo audio cables from AUDIO
OUTPUT on the TV back panel to the TV AUDIO
INPUT on the back of the A/V receiver. The red cable
connects to the R (right) channel and the white cable
connects to the L (left) channel.
B. To connect a digital A/V receiver with Dolby®
Digital surround sound:
Connect one end of the digital audio cable supplied
with the TV to DIGITAL AUDIO on the back of the
TV. Connect the other end to the COAXIAL DIGITAL
INPUT on the back of the A/V receiver.

Satellite Receiver or Other Device with
S-Video

Figure 8
An S-Video cable and audio cables are required. These are not
included with the TV.

Connect an S-Video cable from VIDEO OUT on the
satellite receiver back panel to INPUT-2 S-VIDEO on
the TV back panel.

2. Connect a set of audio cables from AUDIO OUT on
the satellite receiver back panel to INPUT-2 AUDIO
on the TV back panel. The red cable connects to the
R (right) channel and the white cable connects to the
L (left) channel.
Note: Refer to the Satellite Receiver Owner’s Guide
for Dish Antenna connections
"OZ47JEFP%FWJDF
8IJUF

8"3/*/(

"7*4

3*4,0'&-&$53*$4)0$,
%0/0501&/

3*426&%&$)0$&-&$530/26&
/&1"4&/-&7&3

3&$
4063$&
-*/&065

"/5&//"

463306/%
41&",&34 7 .*/

'30/5
$&/5&3

46#
800'&3

5)*4%&7*$&$0.1-*&48*5)1"350'5)&
'$$36-&401&3"5*0/*446#+&$5505)&
'0--08*/(580$0/%*5*0/4 5)*4%&7*$&
.":/05$"64&)"3.'6-*/5&3'&3&/$&"/%
5)*4%&7*$&.645"$$&15"/:*/5&3'&3&/$&
3&$&*7&% */$-6%*/(*/5&3'&3&/$&5)"5.":
$"64&6/%&4*3&%01&3"5*0/

*/165

$0"9*"-

47*%&0

.0/*5037$37$357%7%

7*%&0

.0/*5037$37$357%7%

(/%

"560
45"/%#:

065

'30/5
41&",&34" 7 .*/

*/
*/

$&/5&3
7 .*/

.*546#*4)*
3

*/
$%

065

5"1&

065

5"1&

7$3

065

7$3

%7%

"6%*07*%&03&$&*7&3
.0%&-.73

108&34611-:
7)[
108&3$0/46.15*0/ 8 7"

S
T

"69

%*(*5"-"6%*0

0''

"6%*0

%*453*#65&%#:
.*546#*4)*$0/46.&3&-&$530/*$4".&3*$"
*/$

."/6'"$563&%6/%&3-*$&/4&'30.%0-#:-"#03"503*&4-*$&/4*/(
$03103"5*0/%0-#: 130-0(*$"/%5)&%06#-&%4:.#0-"3&
53"%&."3,40'%0-#:-"#03"503*&4$03103"5*0/
$01:3*()5%0-#:-"#03"503*&4 */$"--3*()54
3&4&37&%

48*5$)&%

"5-"/5*$#-7%."%&*/
+"1"/
/03$3044 ("'"#3*26&&/
+"1"/

6/48*5$)&%

"$7)[
505"-8 "."9

"$065-&54

"73FDFJWFS3FBS1BOFM

6TFPOMZJG
DPOOFDUJOHB
%PMCZEJHJUBM
"7SFDFJWFS

57CBDLQBOFMTFDUJPO
8IJUF

COMPONENT

INPUT
1

YPbPr (480i/480p/720p/1080i)
2

INPUT

COMPONENT

INPUT
1

$0"9*"-

'30/5
41&",&34# 7 .*/

3FE

*/165

065
7

015*$"-

7*%&0065

"6%*0*/

"6%*0065

13&065
463

INPUT

S-VIDEO

VIDEO

AUDIOLEFT/
(MONO)

AUDIORIGHT

S-VIDEO

OUTPUT

DVI
Analog Audio

AUDIO
OUTPUT

RECORD
OUTPUT

AUDIO
OUTPUT

RECORD
OUTPUT

VIDEO

AUDIOLEFT/
(MONO)
AUDIORIGHT

MONITORLINK™/HDMI
VIDEO 480i/480p/720p/1080i
AUDIO PCM LINEAR
1

OUTPUT

DVI
Analog Audio

PC - 60Hz
VGA, W-VGA,
SVGA, W-SVGA,
XGA, 1280 X 720

3FE

VIDEO

AUDIOLEFT/
(MONO)

AUDIORIGHT

' ,INK ¸

AUDIOLEFT/
(MONO)
AUDIORIGHT

MONITORLINK™/HDMI
VIDEO 480i/480p/720p/1080i
AUDIO PCM LINEAR

IR EMITTER
Net Command¸

PC - 60Hz
VGA, W-VGA,
SVGA, W-SVGA,
XGA, 1280 X 720

' ,INK ¸
IR EMITTER
Net Command¸

DTV/CABLE/
VHF/UHF

ANT 1 / MAIN

ANT 2 / AUX

DIGITAL
AUDIO
OUTPUT

CableCARD™ USE WITH ANT 1 CARD TOP
IEEE 1394
INPUT/
OUTPUT

57#BDL1BOFM
4FDUJPO

DTV/CABLE/
VHF/UHF

ANT 1 / MAIN

ANT 2 / AUX

DIGITAL
AUDIO
OUTPUT

CableCARD™ USE WITH ANT 1 CARD TOP
IEEE 1394
INPUT/
OUTPUT

Figure 7. Connecting an A/V receiver
On rare occasions, an HDMI signal may be
copy-restricted and cannot be output from the TV as
a digital signal. To hear these copy-protected signals
through the A/V receiver, use connections for analog A/V
receivers.
MP3 audio from memory cards cannot be output as
digital audio. To listen to MP3 playback from the TV
memory card player through your A/V receiver, use the
connections for an analog A/V receiver
Check the A/V receiver’s Owner’s Guide for information
concerning use of the digital input and switching between
digital sound and analog stereo sound from the TV.

Chapter 2. Connecting

Figure 8. Connecting a Satellite Receiver with S-Video

Note: NetCommand® assumes you connected your
satellite receiver to Input-2. If you add a second
satellite receiver or use any other inputs for your
satellite receiver, this change must match in the
NetCommand system. See Editing NetCommand
Setup in Chapter 3 for more information.

Connecting a DVD Player with Component Video
Connecting a DVI Device
DVD Player with Component Video

Figure 9
Component video cables and audio cables are required.
These are not included with the TV.

Connect the Component Video cables from Y/Pr/
Pb VIDEO OUT on the back of the DVD player to
COMPONENT-2 on the TV back panel, matching the
correct connection:
• Y to Y (Green)
• Pr to Pr (Red)
• Pb to Pb (Blue)
2. Connect a set of audio cables from AUDIO OUT
on the back of the DVD player to COMPONENT-2
AUDIO Input on the TV back panel. The red cable
connects to the R (right) channel, and the white
cable connects to the L (left) channel.
57#BDL1BOFM4FDUJPO

COMPONENT

INPUT
1

YPbPr (480i/480p/720p/1080i)
2

INPUT

OUTPUT

DVI
Analog Audio

S-VIDEO

AUDIO
OUTPUT

RECORD
OUTPUT

VIDEO

8IJUF
Pr

VIDEO

AUDIOLEFT/
(MONO)

AUDIORIGHT

AUDIOLEFT/
(MONO)
AUDIORIGHT

3FE

MONITORLINK™/HDMI
VIDEO 480i/480p/720p/1080i
AUDIO PCM LINEAR
1

PC - 60Hz
VGA, W-VGA,
SVGA, W-SVGA,
XGA, 1280 X 720

DVI Device

Figure 10
A DVI-to-HDMI cable or DVI/HDMI adaptor and HDMI cable and
audio cables are required. These are not included with the TV.
They may be available at your local electronics retailer.

Connect the DVI-to-HDMI cable (recommended) or
HDMI cable with DVI/HDMI adaptor from the DVI
device’s back panel to the TV back panel.
NOTE: If you are using a DVI/HDMI adaptor, it is
important to connect the adaptor to the DVI device for
best performance.

2. Connect a set of audio cables from AUDIO OUT on
the DVI device back panel to the INPUT/DVI Analog
Audio on the TV back panel. The red cable connects
to the R (right) channel, and the white cable connects
to the L (left) channel.
NOTE: The HDMI connection supports copy
protection (HDCP). Some devices require connecting
to an analog input first, in order to view on-screen
menus and select DVI as the ouput. Please review
your equipment instructions for DVI connectivity and
compatibility.

' ,INK ¸
IR EMITTER
Net Command¸

COMPONENT

INPUT
1
DTV/CABLE/
VHF/UHF

ANT 1 / MAIN

DIGITAL
AUDIO
OUTPUT

ANT 2 / AUX

YPbPr (480i/480p/720p/1080i)
2

INPUT

CableCARD™ USE WITH ANT 1 CARD TOP
IEEE 1394
INPUT/
OUTPUT

OUTPUT

DVI
Analog Audio

S-VIDEO

VIDEO

AUDIOLEFT/
(MONO)

AUDIORIGHT

AUDIO
OUTPUT

VIDEO

AUDIOLEFT/
(MONO)
AUDIORIGHT

MONITORLINK™/HDMI
VIDEO 480i/480p/720p/1080i
AUDIO PCM LINEAR

%7%#BDL1BOFM
8IJUF

"6%*0065
:

7*%&0

$)463306/%

#*5453&".1$.

$&/5&3

"$*/
DTV/CABLE/
VHF/UHF

4&3*"-/0

3
46#800'&3 463306/%

'30/5

%*453*#65&%#:

ANT 1 / MAIN

.*546#*4)*%*(*5"-&-&$530/*$4
".&3*$" */$

$0"9*"-

015*$"-

PC - 60Hz
VGA, W-VGA,
SVGA, W-SVGA,
XGA, 1280 X 720

IR EMITTER
Net Command¸

."/6'"$563&%

' ,INK ¸

108&34611-:7_)[
108&3$0/46.15*0/8

7*%&0065

.*546#*4)*

%7%1-":&3
.0%&-

RECORD
OUTPUT

ANT 2 / AUX

DIGITAL
AUDIO
OUTPUT

CableCARD™ USE WITH ANT 1 CARD TOP
IEEE 1394
INPUT/
OUTPUT

+&30/*.030"%
*37*/& $"

3FE

."%&*/+"1"/

%7*UP)%.*$BCMF

57#BDL
1BOFM%FUBJM

Figure 9. Connecting a DVD Player with Component
Video
Note: NetCommand® assumes you connected your
DVD player to Component-2. If you add a second DVD
or use any other inputs for your DVD, this change must
be reflected in the NetCommand system. See Edit
NetCommand... in Chapter 3 for more information.

!.4

%7*%FWJDF

3!4%,,)4%

$6) /54

#!",%

!5$)/
2

46 /54

Figure 10. Connecting a DVI Device

IMPORTANT
See Appendix A for component video signal
compatibility information.
For digital audio connections to your A/V
receiver, see your DVD player and A/V
receiver Owner’s Guides.

Chapter 2. Connecting

Connecting an HDTV Cable Box or Satellite Receiver with
Component Video
Connecting an HDMI Device
HDTV Cable Box or Satellite Receiver
with Component Video
Figure 11
A coaxial splitter, RCA component video cables, and audio
cables are required. These are not included with the TV.

Connect the outside antenna, cable, or satellite to
ANT or SATELLITE IN on the cable box or satellite
receiver. See your device’s owner’s guide for
instructions and cable compatibility.
2. Connect the incoming terrestrial antenna or cable
(not satellite) to ANT-1 on the TV back panel (a coaxial
splitter, available at most electronic supply stores,
may be required to complete this installation).
57#BDL1BOFM4FDUJPO

YPbPr (480i/480p/720p/1080i)
2

INPUT

OUTPUT

DVI
Analog Audio

S-VIDEO

AUDIO
OUTPUT

RECORD
OUTPUT

VIDEO

8IJUF

VIDEO

AUDIOLEFT/
(MONO)

AUDIORIGHT

3FE

AUDIOLEFT/
(MONO)
AUDIORIGHT

MONITORLINK™/HDMI
VIDEO 480i/480p/720p/1080i
AUDIO PCM LINEAR
1

PC - 60Hz
VGA, W-VGA,
SVGA, W-SVGA,
XGA, 1280 X 720

' ,INK¸
IR EMITTER
Net Command¸

DTV/CABLE/
VHF/UHF

*ODPNJOH
"OUFOOBPS
$BCMF

Note: To receive the benefits of a digital A/V receiver,
connect your cable box or satellite receiver’s digital audio
out to a digital input on your digital A/V receiver.

COMPONENT

INPUT
1

HDTV Receiver to TV Back panel
• Y to Y
• Pr to Pr
• Pb to Pb
4. Connect L (left) and R (right) audio cables from the
DTV receiver to Component-1 AUDIO on the TV back
panel.
5. If you are using a satellite receiver, you must
change the input through NetCommand. Open the
NetCommand Connection for [Device] screen (see
page 50) to make the change.

ANT 1 / MAIN

ANT 2 / AUX

DIGITAL
AUDIO
OUTPUT

CableCARD™ USE WITH ANT 1 CARD TOP
IEEE 1394
INPUT/
OUTPUT

HDMI Device
Figure 12

An HDMI-to-HDMI cable is required. This is not included with
the TV. It may be available at your local electronics retailer

Connect an HDMI cable from the TV back panel to the
HDMI device output. HDMI devices provide video and
audio through this cable, so no other connection is
required. You can connect two HDMI devices to the TV
back panel through the HDMI connections.
MONITORLINK™/HDMI
VIDEO 480i/480p/720p/1080i
AUDIO PCM LINEAR
1

DIGITAL
AUDIO
OUTPUT

"6%*0

"6%*0
:

8IJUF

3'
1S

1)0/&+"$,

7*%&0
3&.05&

7*%&0

7$3
$0/530-

3FE
47*%&0

PC - 60Hz
VGA, W-VGA,
SVGA, W-SVGA,
XGA, 1280 X 720

CableCARD™ USE WITH ANT 1 CARD TOP
IEEE 1394
INPUT/
OUTPUT

$"65*0/
3*4,0'&-&$53*$"-4)0$,
%0/0501&/

0655057

%*(*5""6%*0065

$)
$)

*/'30."/5

4"5&--*5&*/

)%.*%FWJDF

)%573FDFJWFSXJUI
:1S1CDPOOFDUJPOT

5PBOUFOOB
DBCMF PSTBUFMMJUF

Figure 11. Connecting an External HDTV Receiver with
Component Video Connections
3. Connect RCA-type cables from the YPrPb outputs on
the HDTV receiver to Component-1 on the TV back
panel, matching the correct connections:

Chapter 2. Connecting

Figure 12. Connecting an HDMI Device
Note: To use the benefits of digital surround sound from
the HDMI device, connect the digital audio output of the
HDMI device directly to the A/V receiver.

Connecting a Computer with an HDMI or DVI Monitor Output

Computer with an HDMI Monitor
Output

Figure 13
An HDMI-to-HDMI cable is required. This is not included with
the TV. It may be available at your local electronics retailer
COMPONENT

Connect an HDMI cable from HDMI 2 on the TV
back panel to the PC’s HDMI output. HDMI devices
provide video and audio through this cable, so no other
connection is required.
INPUT

YPbPr (480i/480p/720p/1080i)
2

INPUT

S-VIDEO

VIDEO

AUDIOLEFT/
(MONO)

AUDIORIGHT

)%.*

OUTPUT

DVI
Analog Audio
1

AUDIO
OUTPUT

RECORD
OUTPUT

VIDEO

AUDIOLEFT/
(MONO)
AUDIORIGHT

MONITORLINK™/HDMI
VIDEO 480i/480p/720p/1080i
AUDIO PCM LINEAR
1

PC - 60Hz
VGA, W-VGA,
SVGA, W-SVGA,
XGA, 1280 X 720

' ,INK ¸
IR EMITTER
Net Command¸

DTV/CABLE/
VHF/UHF

ANT 1 / MAIN

ANT 2 / AUX

DIGITAL
AUDIO
OUTPUT

CableCARD™ USE WITH ANT 1 CARD TOP
IEEE 1394
INPUT/
OUTPUT

57#BDL1BOFM

Computer with a DVI Monitor Output

Figure 14
A DVI-to-HDMI cable or DVI/HDMI adaptor and HDMI cable and
audio cables are required. These are not included with the TV.
They may be available at your local electronics retailer.

Connect the DVI-to-HDMI cable (recommended) (or
DVI/HDMI adaptor with an HDMI cable) from the PC
DVI output to HDMI 2 on the TV back panel.
NOTE: If you are using a DVI/HDMI adaptor, it is
important to connect the adaptor to the DVI device
for best performance.

2. Connect a set of audio cables from AUDIO OUT on
the PC back panel to INPUT/DVI Analog Audio 2 on
the TV back panel. The red cable connects to the R
(right) channel, and the white cable connects to the L
(left) channel.
NOTE: The HDMI connection supports copy
protection (HDCP). Some devices require connecting
to an analog input first, in order to view on-screen
menus and select DVI as the ouput. Please review
your equipment instructions for DVI connectivity and
compatibility.
COMPONENT

INPUT

1$XJUI)%.*0VUQVU

YPbPr (480i/480p/720p/1080i)
2

"VEJP

INPUT

OUTPUT

DVI
Analog Audio

S-VIDEO

AUDIO
OUTPUT

RECORD
OUTPUT

VIDEO

AUDIOLEFT/
(MONO)

AUDIORIGHT

)%.*

AUDIORIGHT

AUDIORIGHT
MONITORLINK™/HDMI
VIDEO 480i/480p/720p/1080i
AUDIO PCM LINEAR
1

PC - 60Hz
VGA, W-VGA,
SVGA, W-SVGA,
XGA, 1280 X 720

' ,INK ¸
IR EMITTER
Net Command¸

Figure 13. Connecting a Computer with an HDMI Monitor
Output

DTV/CABLE/
VHF/UHF

ANT 1 / MAIN

ANT 2 / AUX

DIGITAL
AUDIO
OUTPUT

CableCARD™ USE WITH ANT 1 CARD TOP
IEEE 1394
INPUT/
OUTPUT

IMPORTANT
To view PC video on the TV:
• Activate the PC option in NetCommand. You
can do this during initial NetCommand setup
(in the Device Setup screen), or at any time
afterwards by using the NetCommand Add
function.
• See Appendix A for signal compatibility.

57#BDL1BOFM

%7*UP)%.*$BCMF

1$XJUI%7*0VUQVU
"6%*0065
-&'5

CAUTION: To ensure continued FCC
compliance, the user must use a
shielded video interface or HDMI cable
with bonded ferrite cores at both ends
when using the PC input.

$6) /54

3*()5

Figure 14. Connecting a Computer with DVI Monitor
Output

Chapter 2. Connecting

Connecting the IR Emitter NetCommand®

IR Emitter NetCommand®

Figure 15
An IR emitter cable is included with the TV.

•

The emitter end being used can be secured in place
using double stick tape.

The emitters connected to these jacks are used by the
NetCommand system and by TV Guide On Screen® to
control other devices such as VCRs, DVD players, Cable
boxes and Satellite receivers.

•

If you are not going to be using all emitter ends, place
the unused ends behind the devices so that they
cannot send signals to the remote control sensors.
$0.10/&/5

*/165

Connect the plug end of the supplied IR Emitter
Cable to either one of the IR Output NetCommand
jacks on the TV back panel.

The remote control sensor is usually behind the
plastic window of the front display panel. It is
sometimes visible when you look through the display
plastic using a flashlight and is normally a round or
square cutout behind the plastic. If you cannot see
the sensor and the device’s Owner’s Guide does
not specify the location, you can find it by using the
device’s remote control.
a. Hold the remote about one-half inch from the
front of the device. Starting from one end of the
display window plastic, press the POWER button.
b. If the device does not respond, move the remote
control one inch toward the center and try again.
c. Repeat this until the device responds.
d. Note this location and then start over from the
other end of the display window plastic, repeating
until the device responds again.
The remote control sensor will be somewhere
between these two positions. This is usually
enough accuracy for the placement of the IR
emitters.
•

With some devices, the emitter works better facing
downward from the top of the device. Some
experimentation may be needed.

Chapter 2. Connecting

:1C1S JQQJ

7*%&0

"6%*0
-&'5
.0/0
"6%*0
3*()5

0UIFS"7EFWJDF

2. Run the cable for each of the emitter ends under,
alongside, or over the top of each device to be
controlled to the area of the front where the remote
control sensor is located.
3. Place the emitter end in front of the remote control
sensor of the device to be controlled. The emitter
bulb should face the remote control sensor. This bulb
emits infrared light in a cone shaped pattern. The
bulb needs to be placed far enough from the remote
control sensor to allow the cone pattern to include
the sensor.

47*%&0

(-JOL¸
*3&.*55&3
/FU$PNNBOE¸

%57$"#-&
7)'6)'

64&8*5)

$BCMF$"3%
"/5"69

"/5."*/

% * ( * 5 " -

463306/%

"73FDFJWFS

0UIFS"7EFWJDF

Figure 15. Connecting IR Emitter NetCommand

IMPORTANT
If a single emitter end can be placed in a
position that will operate more than one device,
do not use a separate emitter end for the
additional device. A single device receiving
remote control signals from too many emitters
or remote controls may not respond at all.

Connecting Compatible IEEE 1394 Devices
Compatible IEEE 1394 Devices

Compatible A/V devices include some, but not all, cable
boxes, D-VHS VCRs, A/V discs, and future products. It
is also possible to connect devices to the TV that have
IEEE 1394 connectors but are not compatible with the
TV or with the NetCommand® control system. Areas of
compatibility to consider are:
1. Digital Video Signals
The TV is able to decode MPEG2 and DV video as
provided by some camcorders. If the TV is unable to
decode the digital signal supplied by your camcorder, try
S-video with analog audio connections instead. Other
types of digital video, such as PC video provided by
some computers, must be decoded by the source device
and sent to the TV as analog video, S-video, or HDMI
video.
2. Digital Audio Signals
When received with video signals, the TV is able to
decode Dolby Digital signals and MPEG audio signals.
Other types of digital audio as provided by some digital
recording devices, such as MP3 audio and DTS audio,
cannot be decoded by the TV when received over IEEE
1394

When Connecting IEEE 1394 Devices
•

%JHJUBM
%7%
%JHJUBM
7$3
57

•

The TV may not be able to pass incompatible digital audio
signals on the coaxial digital audio output, however, these
signals may pass on the IEEE 1394 cable to other devices.

3. Digital Control Signal
The TV can serve as the control center for IEEE 1394
audio/video devices, such as VCRs, A/V Discs, tuners,
cable boxes and amplifiers that are compatible with the
following IEEE 1394 control standards.
•

EIA-775 is designed for tuning devices such as cable
boxes, allowing the device to send simple graphics.
This standard does not, however, allow the TV to
control the cable box by IEEE 1394.

•

AV/C (Audio Video Control) is designed to provide
basic controls such as play, stop, channel selection,
and volume, as appropriate for the device.

The IEEE 1394 interface may not provide reliable control
signals for some DV camcorders, especially older models.
If your camcorder operates incorrectly or not at all, use
the camcorder’s control buttons instead of the IEEE 1394
connection.
Some devices may be a combination of two or more
types of devices. For example, there may be a recording
device that is also a tuning device. Each portion of the
device is called a sub-unit. When you select a device on
the Device Selection menu that has sub-units, a pop-up
menu will appear so you can select which sub-unit
section you wish to use.

Do not loop the last device in the chain back to the
TV. When the device chain is looped, the TV may not
be able to work with the other devices.

•
•

Place devices that have only a mechanical
(two-position) power switch at the end of the chain
or leave the power switch in the On position. When
turned Off, IEEE 1394 signals may not be able to
pass through the device to other devices.
Place devices with the slowest communication
speed at the end of the chain. Sometimes the
communication speed will be marked near the IEEE
1394 connector with an “S” number. The higher the
number, the faster the communication speed. This
TV has a communication speed of S400. Devices
with slow communication speed can interfere with
IEEE 1394 signals from faster devices. When using
NetCommand to set up a digital recording between
a faster device and a slower device, make the slower
device the source and make the faster device the
recorder.
Do not use an IEEE 1394 cable over 15 feet in length
between each device.
This TV is an IEEE 1394a device. It can be used
with a 1394b system when an IEEE-1394a-to-1394b
convertor is used. 1394b systems are capable of
greater distances and multi-room applications.

IMPORTANT
DV Camcorder Playback
A. When viewing DV camcorders, it is normal
for temporary audio and video distortion to
occur under conditions such as:
• Playback start and stop
• Playback pause
• Forward or reverse picture search
B. Some DV Camcorder models are not
compatible with this TV’s IEEE 1394 system.
Because of this, the “New 1394 Device”
screen will not appear when the camcorder
is connected. For playback of incompatible
DV camcorders, try S‑video with analog
audio connections instead.

Chapter 2. Connecting

Connecting Compatible IEEE 1394 Devices, continued

Connection Styles

There are two different connection styles that can be
used when connecting IEEE 1394 devices. Use the style
that fits your network of audio/video products.

4-Pin-Style vs. 6-Pin-Style Connectors

There are two different types of connectors used for IEEE
1394 terminals and cables: a 4-pin and a 6-pin style.

Direct Device-To-Device Style

The IEEE 1394 offers you the capability to chain devices,
unlike previous audio and video connections where you
had to individually connect each device directly to the
TV. For example, you can connect your D-VHS to your
1394 DVD Player and then connect the 1394 DVD Player
to the TV. The resulting IEEE 1394 chain will allow you to
add more devices to the chain. You will be able to see
each video device on the TV’s Device Selection Menu
and send information from any IEEE 1394 device to other
compatible devices.

4 pin connector

6 pin connector

Hub Connection Style

The IEEE 1394 also offers you the capability to connect
your devices using the TV as a hub within the audio/
video network. Each device can send information,
which may include audio and video, to any other device
in the network.

Digital
DVD #1
1394
Monitor

Digital
VCR #3

TV
Digital DVD #2

D I G I T A L

SURROUND

Other
1394 Device #1
Digital VCR #2

Other 1394 Device #2

Chapter 2. Connecting

The 6-pin connector can send
the same digital audio, video,
and control signals as the 4-pin
connector, but the 6-pin connector
can also send low-voltage electrical
power. This TV does not have 6-pin
connectors.

The purpose of this low-voltage electrical power is to
provide the needed operating power to a device that is
not connected directly to the household AC power, such
as a camcorder. A device with a 6-pin connector can
send this electrical power to another device, or receive
electrical power from another device, or simply use a
6-pin connector without using the two additional pins.

Digital
VCR

Digital
DVD

The 4-pin connector sends digital
audio signals, digital video signals,
and digital control signals back and
forth between devices. Your TV
has three 4-pin-type connection
jacks available. One is on the front
panel and two are on the back.

Digital
VCR #1

6 pin to 4 pin adaptor

A 6-pin connector cannot be
connected directly to a 4-pin jack,
and vice versa. To connect a 6-pin
device to a 4-pin device, you need
to obtain a 6-pin-to-4-pin adaptor
or adaptor cable. These cables
are available from electronic and
computer stores.

When connecting a 6-pin device (such as a camcorder)
to the TV, (if it is designed to receive electrical power
from another 6-pin device) you will need to connect
the camcorder directly to the household AC, or use the
camcorder’s battery for power. If this is not possible,
then the camcorder will need to be connected directly to
another 6-pin device in the network that can provide the
electrical power.

Helpful Hints for NetCommand Connections

Q. My VCR (or other device) does not have two sets of stereo audio outputs. How can I connect this device’s
audio to both the TV and the A/V Receiver?
A. Connect the single set of stereo audio outputs to the TV only. Use Edit NetCommand® to change the setup of this
device. In the Connection screen of “Change” make sure both audio and video for the TV input are check marked
and the audio for the AVR input is not check marked. This will allow the NetCommand system to use the TV
outputs to transfer the device’s audio to the A/V Receiver. See Edit NetCommand in the next chapter for details.
Q. I have both the TV stereo audio output and TV digital audio output connected to the same input
designations on my A/V Receiver. How do I switch between analog audio and digital audio?
A. In most setups, analog audio is also output as digital audio, so no switching is required, and there is no need to
connect the analog output. In some circumstances, however, you may also need analog audio from the TV. For
example, MP3 audio is only output in analog format, so you must connect the TV’s analog AUDIO OUTPUT to the
A/V Receiver if you want to hear MP3 audio through the A/V receiver. Refer to your A/V Receiver user’s guide to
find out how analog/digital audio switching works.
• If your A/V Receiver’s remote control has an Analog/Digital Audio key, you can use the GUIDE key with the
following models to control switching:
Mitsubishi M-VR900
Denon AVR-2700

Integra DTR-9.1
Kenwood VR-2080

To make the switch, press the Device key on the TV’s remote control, and from the Device Selection menu,
press the Audio key. Then, with the A/V Receiver highlighted, press the GUIDE key to make the switch.
•

If you have some other A/V Receiver model, use the TV’s learn function to learn the analog/digital audio
code for the GUIDE key. Follow the instructions above for using the GUIDE key.

•

If your A/V Receiver has an Analog/Digital selection key on the front panel only, and not on the remote, then
your only option is to use that key to perform switching.

Q. The front panel of my A/V Receiver is too tall or too convex for the IR emitter signal to reach the remote
control sensor of the A/V Receiver. What can I do?
A. There are several possible solutions.
1. Mount the IR Emitter on the top, front edge of the A/V Receiver over the remote control sensor. Use tape to
secure it in place.
2. Mount the IR Emitter on the underside of the shelf above the A/V Receiver (if the A/V Receiver is in a cabinet).
Use double sided tape to secure it in place.
3. Some small stick-on emitters from other manufacturers may be compatible with this TV’s IR Emitter jacks.
These may be used instead of the supplied IR Emitters.
Q. I occasionally need to see the menu from my A/V Receiver. How can I connect it to the TV for this purpose?
A. You can connect the video output of the A/V Receiver to an unused input on the TV. Then use Edit NetCommand
to “Add” this as an “Other” device, not an A/V Receiver. On the “Connection” screen, indicate which TV input was
used and check mark the video box. Make sure the TV input audio box and both the audio and video boxes for
the AVR input are not check marked. You should also name this device so you can easily identify it on the Device
Selection Menu. You can also use Input 3 on the front panel.
Q. I have a high definition receiver I would like to connect and it also has an S-video output I would like to be
able use as well. Is there any way to connect this receiver both ways?
A. Yes, this item will appear twice in the Device Selection Menu. Just add this unit once using the Component-1 and
once using one of the S-video inputs. Make sure you indicate that this is the same manufacturer for both. We
suggest that you connect stereo audio outputs with the S-video to the TV so that you do not need to use two inputs
on the A/V Receiver. If this is a NetCommand compatible HDTV receiver and HD or SD outputs can be switched by
remote control, see Edit NetCommand in the next chapter for NetCommand control of this feature.

Chapter 2. Connecting

Chapter . . .

NetCommand® Setup and Editing
NetCommand® Introduction. . . . . . . . . . . . . . .
Using the Remote Control with NetCommand® .
NetCommand® Setup On-Screen Buttons. . . . .
Menu System. . . . . . . . .
3D Graphical
NetCommand® Initial Setup. . . . . . . . . . . . . . .
Edit NetCommand®: Add an A/V Receiver. . . . .
Edit NetCommand®: Add Devices . . . . . . . . . .
Edit NetCommand®: Change or Delete Devices.
IEEE 1394 Devices and NetCommand® Control..
Adding IEEE 1394 Devices Automatically.. . . . . .

.
.
.
.
.
.
.
.
.
.

38
39
40
41
42
45
48
52
53
54

NetCommand® Introduction
NetCommand makes your TV the heart of your Home Theater
NetCommand® is an intelligent control system that makes your Mitsubishi TV the heart of your home theater. With
NetCommand, the TV sends signals to the other devices in the system via the IR emitters, telling the devices to play,
record, change inputs, adjust volume, change channels and many more functions. All of this is accomplished with one
remote control and without changing control layers.
IR Learning and IEEE 1394 Support
The IR “Learning” feature of NetCommand allows the TV to learn the
remote control signals for new devices that the TV is not preprogrammed
to operate. NetCommand® also includes the capability of controlling IEEE
1394 devices by sending control signals on a FireWire® cable.
Using NetCommand is completely optional
When you first turn on the TV, the NetCommand Setup Wizard launches. If you decide to use NetCommand, follow
the on-screen instructions. If you choose not to use it right away, simply quit the Setup Wizard and NetCommand will
remain inactive. Later, if you decide to use NetCommand, you can easily access the Setup Wizard.
NetCommand and Levels of Control
When you set up NetCommand, you decide how much control you want the TV to have over your home theater system.
You have the choice of performing a basic, limited, or complete NetCommand setup.
• Basic Setup
In a basic setup, NetCommand will:
◊ automatically switch to the correct TV input when you want to view programming from a different device. All
you do is select the device from the on-screen device selection menu. This saves you from having to search for
the correct input every time you want to change devices. Unused inputs are automatically deactivated so that
you don’t see them in the menu.
◊ show an on-screen icon for each device connected to the TV so you always know what devices are available.
Note that with a basic setup, you still need to use the remote control specific to each device.
•

Limited Setup
In a limited setup, you get the benefits of the basic setup plus NetCommand control over the specific devices you
have chosen. Use this type of setup if you:
◊ only want NetCommand to control a few devices, such as the TV, a playback device (like a DVD player), and a
cable box. With this setup, you can use the TV’s remote to control these devices.
◊ want to use TV Guide On Screen® to control your cable box and VCR and/or A/V disc. After performing this
setup, you can use the TV’s remote to control these devices.

•

Full Setup
Perform a full setup if you want NetCommand to:
◊ control a surround sound A/V receiver.
◊ automatically change input selections for the A/V receiver.
◊ control all devices with the TV’s remote, including the A/V receiver.

NetCommand Helps You Manage Your Home Theater
With the NetCommand Review screen you can:
• view a summary of all devices connected to the TV and the input used for each device.
• deactivate or turn off unused input connections; reactivate or turn them on.
If you need to change your setup, the NetCommand sub-menu lets you easily
• add new devices.
• deleted devices you have disconnected.
• change device and input selections.

Chapter 3. NetCommand Setup and Editing

Using the Remote Control with NetCommand®
Below is a list of several manufacturers’ devices tested and shown to be compatible with NetCommand. These devices
can be controlled without changing the setting of the remote control from TV to another product. NetCommand may
be able to operate additional models, since many manufacturers use the same control signals to operate some or all
of the models they offer. This chart lists only the models that have been tested with NetCommand. The NetCommand
Learning feature is able to learn the remote control signals of most audio/video devices. For devices not listed in the
table, or if your device does not operate using the same remote control as the models listed below, use the learning
feature by selecting “Other” at the [Device] screen. See the Edit NetCommand section of this Guide.
NOTE: There are many different types of remotes and not all of them may be compatible with the learning feature.
Bright light near the TV screen can also adversely affect the learning feature. If it is not possible to learn a device, you
will need to use the original remote control of the device, or program the TV remote to operate these devices in the
traditional manner.

NetCommand Pre-Memorized Devices
DEVICE
A/V receiver

M A N U F A C T U R E R

Mitsubishi
Bose
Denon
Echostar
Funai
General
Instruments
Hitachi
Hughes
Integra
Jerrold
JVC
Kenwood
Marantz
Microsoft
Motorola
Panasonic
Philips
Pioneer

Cable Box

M-VR800,
M‑VR900
Lifestyle® 28
AVR-2700

Toshiba
Yamaha
Zenith

DVD Player

VCR

SR-HD5

DD-6000, DD-8020

HS-U795,
HS‑U778

Lifestyle® 28
6000
F260LA
CFT2200
DV-P415U

VT-FX665A

HIRD-E45,
HIRD-E86
DTR-9.1

DPS-9.1
Not
specified
XV-S65GD

HR-VP 650U

VR2080
SR8200
XBox™ (requires the DVD kit from
Microsoft)
DCT2244
TU-HDS20
VSX-D557,
VSX-49TX

DVD-A310

PV-8662
VR620CAT

DV-414

RCA
Rotel
Scientific Atlanta
Sharp
Sony

SAT Satellite
Receiver

DRD480RE,
DTC-100
RSX-1065
8600
STR-DE825

SAT-A55

DTS-3000
RX-V2095,
RX-V2200

DVP-S500D, PlayStation® 2
(Playstation® 2 requires the DVD Remote
Controller kit from Sony; DVD Player
software disc version 2.10)
SD-9200, SD-5109
DVD-S520, DVD-C996

VC-H810U
SLV-778HF

W-717

DTV1080

Chapter 3. NetCommand Setup and Editing

NetCommand® Setup On-Screen Buttons
To use the TV’s NetCommand feature, you need to provide some detailed information during the setup of your
Mitsubishi TV. You must define the manufacturer of the devices that are connected to the television, or learn the IR
code remote control signals for the device connected. For each device, the input to the TV and A/V receiver, and the
names for the device are pre-set during Initial NetCommand setup. You may change those inputs or names using the
Edit NetCommand or Learn screens. The buttons described below will help you navigate the screens.
On your remote control, the ADJUST or buttons allow
you to navigate left and right to different selections on the
screen. The ADJUST or buttons allow you to:
•

Change the radio button

•

Change current text box selection

•

Navigate up and down on the screen

Control Buttons

Much like the software on your computer, you will use
graphic buttons to navigate through the NetCommand
Setup screen. Highlight the button and press ENTER to
select the function.

Button

Text Box

Press ADJUST

to make a selection.

Check Box

Check marks indicate the item or input is added or turned
On. Press ENTER when the check box is highlighted to
add or delete a check mark. When viewing the Review
screen, a check box reflects which devices are turned On
or Off, or connected to the TV.

Radio Buttons

Use the Next> button to navigate forward to the next
screen.

Cancel Button

The Cancel button will cancel out any changes you
are currently making without saving them into memory.
When you select the Cancel key, NetCommand will
prompt you to confirm that you want to cancel the
changes you are currently making. If you select Cancel
during Initial Setup, you can set up NetCommand later by
selecting the NetCommand menu, then choosing Initial.

The setting changes when one of the choices is
highlighted.

Chapter 3. NetCommand Setup and Editing

3D Graphical

Menu System

Your TV also has Mitsubishi’s exclusive 3D Graphical on-screen operating system, which provides on‑screen
information for menu choices and changes, using the TV’s remote control.

Remote Control Buttons

Menu Screens
A picture (icon) is highlighted on the menu
screen when selected with the ADJUST
arrows. You may then make changes
within the menu or access sub-menus, if
available.
You can also access sub-menus from a
button. Sometimes when you select a
button, an automatic function begins.
The
features:

system includes the following special

•

The currently selected icon or button is
highlighted with a yellow outline; the text color is
yellow.

•

On-screen instructions, shown in the message
line at the bottom of the menu, provide feature
selection and adjustment information.

•

Some on-screen menu options must be set
before other options are available.

The following buttons on your remote control help you
navigate within the
system:
1.

ADJUST
change.

2. ADJUST

to select the menu item you want to
to change the settings.

%7%
3. ENTER to $"#-&%#4%57
open a menu,7$3
start
an automatic function,
"6%*0
57
or select a check box.

4. TV MENU to display the main menu or move back
one menu screen at a time.

5. CANCEL to clear a setting or stop an
automatic
108&3
function.
6. HOME to exit all menus and return to TV viewing.

46#$"/$&-

427

%&7*$&

70-

.65&

1"(&

Main Menu: This screen is always the first to appear
when you press the remote’s TV MENU button.

(6*%&

57.&/6

%&7*$&
.&/6

)0.&

7$)*1

"6%*0

*/'0

7*%&0

Press ADJUST or to change text boxes. Some text
boxes have preset
Other&9$)
boxes 4-&&1
allow you to select
1*1101
1*1$) labels.
letters, numbers or characters to customize names.
1*1%&7*$&

'03."5

3&$

$0//&$5

1"64&

1-":
'''8%

3&83&7

4501

Chapter 3. NetCommand Setup and Editing

NetCommand® Initial Setup

The initial setup screens that appear when you first power
on your new Mitsubishi TV guide you through setup of
NetCommand and the TV Guide On Screen® system.
Most IR remote control signal formats can be learned by
NetCommand.

Welcome Screen
Figure 1

When you first turn on your TV, the NetCommand
Welcome screen displays and asks you to select either
English or Spanish as the language for the on-screen
menus. The default language is English. To change
Language later, select Setup in the Main Menu. Selecting
Cancel at this screen will cause the default language
(English) to be selected.

Select Next> and press ENTER to start the initial
setup.
If the NetCommand Setup is cancelled before it’s
completed, you can restart the NetCommand setup
from the Setup Reminder screen (see below) or by
doing the following:
1. Press TV MENU on the remote control to display
the TV Main menu.
2. Select NetCommand. The available options will be
Add, Review, Guide or Initial. Change and Delete
will be grayed out.
3. Press ADJUST
to select Initial.
4.

Press ENTER. The Device Setup screen (shown
on the next page) displays.

Setup Reminder
Figure 3

This screen only appears if you did not set up
NetCommand when the TV was first turned on. The
Setup Reminder screen displays for the next six times
you power on the TV.

Figure 1. Welcome screen

If you would like to set up NetCommand and/or the
TV Guide On Screen system, select Next and press
ENTER. If you do not wish to set up NetCommand
and/or the TV Guide On Screen system, then select
Cancel and press ENTER.

NetCommand (Information) Screen
Figure 2

The NetCommand (Information) Screen describes how
to start or delay the initial NetCommand and TV Guide
On Screen setup. This screen displays automatically the
first time you power On your new TV, after the Welcome
screen.

Figure 3. Setup Reminder screen

IMPORTANT

Figure 2. Information screen

Chapter 3. NetCommand Setup and Editing

You may use your TV without setting up
NetCommand or the TV Guide On Screen®
system. To set up at a later time, choose the
NetCommand menu from the Main menu,
then select Initial. The TV Guide On Screen
system is set up from the NetCommand
menu.

NetCommand® Initial Setup, continued

Device Setup Screen

TV Guide On Screen® System Setup

If the devices connected to the TV are already in
NetCommand memory, you can quickly select them
at this screen. Press ADJUST or to move to each
device type. Press ADJUST or to select the
manufacturer. Select “Other” if the manufacturer is not
listed. Later, you can use the Change setting in the Edit
NetCommand menu to learn the remote control signals
for this device. Select “None” for device types that are
not connected.

The TV Guide On Screen option allows you to select
whether you want to enable the TV Guide On Screen
system and, if so, which devices to include. To receive
the correct program listings for your area, you will need to
enter your five-digit ZIP code.

Figure 4

For the A/V Receiver, if the manufacturer is not listed, you
cannot select “Other”. Instead, select “None”. Later, you
can use the “Add” feature in the NetCommand menu to
have the TV add and learn the remote control signals for
this device.
If you have a camcorder connected, check the
Camcorder box. NetCommand will not be able to
control it, but will reserve the front input to use with
the camcorder. Check the PC box if you have a PC
connected. After completing your choices, select Next>
and press ENTER.

Figure 5

You can select one over-the-air source and one cable
source for TV Guide On Screen. If, however, you have
multiple cable sources, the channel-number assignments
may not match up correctly. See the table below for the
preferred connection combinations.
If One Source Is:

The Other Source Can Be:
Ant-1 Air

Ant-2 Air

Cable Box
Cable Card

N/A

Ant-1 Channels via Cable

N/A

Ant-2 Channels via Cable

N/A

For detailed information on using the TV Guide On
Screen system, please see the separate TV Guide On
Screen Interactive Program Guide User’s Manual.

Figure 4. Device Setup screen
Note: If you selected “Other” for any of the device
names, you can direct the TV to “Learn” the connected
device by following the Edit NetCommand instructions.
For many device types, non-listed models will operate in
the same way as the listed models and you can still use
the pre-loaded setting.

IMPORTANT
NetCommand must be set up and the IR
emitters properly placed for your cable box
and VCR so the TV Guide On Screen system
can control these devices.

Figure 5. TV Guide On Screen
Note:
• Inputs to TV Guide On Screen can include:
Only one over-the-air source
Only one cable source
• An antenna input is required for downloading TV
Guide On Screen schedules. If your cable box is
connected using HDMI or IEEE‑1394, you must also
connect an antenna input.
• If your cable box is connected to a Component input,
be sure the box is set to send analog channels as
480i. If this is not possible, add an antenna input.

Chapter 3. NetCommand Setup and Editing

NetCommand® Initial Setup, continued

Review Screen

Finish Screen

After you have made your device choices, the Review
Screen will display. It is important to review the settings
to ensure that they are correct. If necessary, you can
use on the Review screen, all
selections made are finalized.

Figure 7. Finish screen
It may still be necessary to memorize the available
channels for Antenna-1 (and Antenna-2, if used).
You may do that by going to the TV Main menu and
selecting Setup. Instructions to memorize channels are
found in the Setup menu section.

On the Review screen, adding or deleting check marks
will turn the adjacent devices or inputs On or Off. 1394
device names only appear on the Review screen when
the devices are connected to the TV.

Chapter 3. NetCommand Setup and Editing

Edit NetCommand®: Add an A/V Receiver

A/V Receiver Screen
Figure 8

If your A/V Receiver manufacturer was not listed, and you
selected “None” during the initial NetCommand setup,
you may add the A/V Receiver and have NetCommand
learn its remote control’s functions. Either select Edit
from the Finish screen or, if you have finished the initial
setup, go to the Main menu, select NetCommand, then
press ENTER. The Edit NetCommand screen will display.
Select Add.

NetCommand to switch inputs to use this device.
However, NetCommand will not be able to control
this device. Later you may use the “Change” option
in the NetCommand menu to learn the remote control
signals.
After selecting Next>, the screens that follow are: the
A/V Receiver Input screen (Figure 9), Name screen
(Figure 12), Audio Output to AVR screen (Figure 13),
ending with the Finish screen (Figure 14).

A/V Receiver Inputs
Figure 9

Figure 8. A/V receiver screen
Choose ONE of these options:
•

Select a recognized manufacturer. The model
number optimized for NetCommand will display at
the bottom of the screen. If a number follows the
manufacturer’s name, (example: Mitsubishi 1), this
indicates additional models are optimized for that
manufacturer. For many device types, non-listed
models will operate in the same way as the listed
models and you can still use the pre-loaded setting.
After selecting Next>, the screens that follow are:
the Name Screen (Figure 12), Audio Output to AVR
screen (Figure 13), ending with the Finish screen
(Figure 14).

•

Select “Other,” then highlight “Learn” and press
ENTER. This will allow you to have NetCommand
learn the remote control signals of this new device.
After selecting “Learn” and pressing ENTER, the
screens that follow are: the A/V receiver Inputs
screen (Figure 9), A/V Receiver Input Learn screen
(Figure 10), A/V Receiver Learn screen (Figure 11),
Name screen (Figure 12), Audio Output to AVR screen
(Figure 13), ending with the Finish screen (Figure 14).

•

Select “Other,” skip Learn and select Next>. This
will allow the device to appear and will allow

If you select “Other” as the manufacturer and then
“Learn,” you will see the A/V Receiver Input screen. After
selecting the number of inputs, this screen will not appear
again.
Depending on your A/V Receiver’s capability, you may
connect up to seven A/V inputs. Select the number of
inputs by pressing ADJUST or .
If the number of connected inputs changes, you will need
to delete the A/V receiver through Edit NetCommand and
add it again, as described above.

Figure 9. A/V receiver Input screen

Chapter 3. NetCommand Setup and Editing

Edit NetCommand®: Add an A/V Receiver, continued

A/V Receiver (AVR) Input Learn Screen

A/V Receiver (AVR) Learn Screen

NetCommand can now learn the remote control signals
used to select each input on the A/V receiver.

Figure 10

Press ADJUST or on the TV remote to select the
check box for each function to be learned.

2. Press ENTER and the function name will begin to
flash to confirm the ready-to-learn status.
3. Press the button on the A/V receiver’s remote control
that corresponds to the selected function. A check
mark will appear and the function name will stop
flashing. This confirms the signal learned status.
4. To test the learned command, press ENTER on the TV
remote. The A/V receiver will perform the selected
function. The A/V receiver needs to be turned on
and the IR emitters properly placed for the test to be
successful (see page 32 for IR emitter placement).
5. To customize the input names, press ADJUST to
move to the Input Name text box and then press
ADJUST or and ENTER to select each letter of
the name. These names will appear on the Review
screen as the A/V receiver’s input names, and should
match the names the A/V receiver shows in its own
display.

Figure 11

Press ADJUST or
on the TV remote to select the
check box for each function to be learned.

2. Press ENTER and the function name will begin to flash
to confirm the ready-to-learn status.
3. Press the button on the A/V receiver’s remote control
that corresponds to the selected function, A check
mark will appear and the function name will stop
flashing. This confirms the signal learned status.
4. To test the learned command, press ENTER on the TV
remote. The A/V receiver will perform the selected
function. The A/V receiver needs to be turned on
and the IR emitters properly placed for the test to be
successful (see page 32 for IR emitter placement).
5. Repeat for each function to be learned.
6. To erase a learned function, highlight the check box
for that function and press CANCEL.
7.

When the function signals have been learned, press
ADJUST to select Next> and move to the Name
screen.

6. To erase the learned input signal, highlight the check
box for that input and press CANCEL.
7. Repeat for each connected input.
8. When the input selection signals have been learned
and the inputs named, press ADJUST to select
Next> and move to the A/V receiver Learn screen.

Figure 11. A/V receiver Learn screen

Figure 10. A/V receiver Input Learn screen

Chapter 3. NetCommand Setup and Editing

IMPORTANT
When learning remote control signals, point
the device’s remote at the TV screen

Edit NetCommand®: Add an A/V Receiver, continued

Name Screen

Finish Screen

The Name screen allows you to change the default name
for the A/V receiver to a custom name of up to eight
characters (including a blank space), selecting from
letters, numbers, and nine different characters. Using
the TV’s remote, press ADJUST or to select each
letter, then press ENTER to move to the next position.
Press CANCEL to delete the current letter and move back
one character position. When in the first position, the
CANCEL button will return the name to the default name.

To finalize your selections and complete the A/V
receiver setup, select Finish from the Finish screen.

Figure 12

Figure 14

Note: If you connected the audio output of other
devices directly to the A/V Receiver, you must use
the “Change” function of the Edit NetCommand
menu and select each device to assign the correct
A/V Receiver input to be used with each device.

Figure 14. Finish screen
Figure 12. Name screen

Audio Output to AVR Screen
Figure 13

Use this screen to select which A/V Receiver input is
connected to AUDIO OUTPUT on the TV back panel.
Press ADJUST to select Next> and move to the Finish
screen.

Note: To change any of the inputs or names for the
devices, or add devices not included in the initial
settings, select Edit to display the Edit NetCommand
menu.

IMPORTANT
NetCommand does not allow you to delete
an A/V receiver or change the audio
connections for a device (such as the TV or
a DVD player) if the A/V receiver is currently
being used.
To delete or change the A/V receiver audio
connections, you must be listening to the TV
speakers.

Figure 13. Audio Output to AVR screen

Chapter 3. NetCommand Setup and Editing

Edit NetCommand®: Add Devices
Mitsubishi’s NetCommand allows you to edit your home theater configuration. You can add new devices, change
device settings and connections, delete devices and learn remote control IR signals not already in NetCommand
memory.

Edit NetCommand Screen

Add Screen

If you selected Edit when you were at the Finish screen,
the Edit NetCommand screen displays. Your choices are:

Select “Add” from the Edit NetCommand screen, and the
New Device screen will display. Select the Device type
that you would like to add. You may add your A/V receiver
(if not added in Initial setup) Cable Box, Camcorder, SAT
(satellite), DVD, Laser Disc, PC and VCR.

Figure 15

Add
Add a new device to the NetCommand setup. “Learn” the
remote control signals of devices listed as “Other” brands.
See Figure 16.
Change
Change the brand/model, input connections, or name of
a device already listed in the configuration. “Learn” the
remote control signals of devices listed as “Other” brands.
See Figure 25.
Guide
Edit TV Guide On Screen® ZIP code and input selections.
See the separate TV Guide On Screen Interactive
Program Guide User’s Manual for more information about
customizing the Guide. See Figure 5.

Figure 16

At the next screen, choose the manufacturer. If you
choose “Other” for the manufacturer, the device (A/V
receiver, Cable, SAT, DVD or VCR) can be learned. For
device types Laser Disc, Camcorder, Game and PC, the
“Learn” screen is skipped. There is no NetCommand
support or learning for these devices.
At the next screen, you can keep the default Name or
select a custom Name for the device, using ADJUST
or to select letters A–Z, numbers 0-9, and/or symbols
(!.&’/:*- and blank) for each character of the name you
would like for the selected channel.

Review
View a list of all devices and input connections in the
NetCommand home theater configuration, including the
A/V receiver. This is also where you can turn On or Off
unused TV inputs or devices. See Figure 6.
Delete
Remove a device or erase the complete NetCommand
home theater configuration. The learned remote control
signals are erased when the associated device is deleted.
See Figure 26.
Initial
Start the setup at the beginning. This button only
becomes available after deleting the complete
configuration, or if NetCommand was not set up when the
TV was first powered On. See Figure 2.

Figure 16. Add screen
Hint: The cable box and satellite receiver learn screens
include PVR functions.

Figure 15. Edit NetCommand screen

Chapter 3. NetCommand Setup and Editing

Edit NetCommand®: Add Devices, continued

[Device] Screen

•

Figure 17

If you selected “None” for a device type during initial
setup, you can later add a device with this screen. This
screen also opens when you select the Change option in
the Edit NetCommand screen.

Select “Other”, skip Learn and select Next>. This
will allow the device to appear and will allow
NetCommand to switch inputs to use this device.
However, NetCommand will not be able to control this
device. Later you may use the “Change” option in the
Setup menu to learn the remote control signals.
After selecting Next>, the screens that follow are: the
Name Screen (Figure 20), Connection screen (Figure
21) and specialized device screens (Figures 22-24),
ending with the Finish screen (Figure 27).

The sample screens here show the choices for adding a
VCR; similar screens will appear for any satellite receiver,
DVD player, or cable box.

[Device] Learn Screen

Figure 18
Shown only if “Learn” was selected

Press ADJUST
to select the check box for
each function to be learned.

2. Press ENTER and the function name will begin to
flash to confirm the ready-to-learn status.
3. Press the button on the device’s remote control that
corresponds to the selected function. A check mark
will appear and the function name will stop flashing.
This confirms the signal learned status.

Figure 17. [Device] screen

Choose ONE of these options:
•

Select a recognized manufacturer. The model
number optimized for NetCommand will display at
the bottom of the screen. If a number follows the
manufacturer’s name, (example: Mitsubishi 1), this
indicates additional models are optimized for that
manufacturer. For many device types, non-listed
models will operate in the same way as the listed
models and you can still use the pre-loaded setting.
After selecting Next>, the screens that follow are: the
Name Screen (Figure 20), Connection screen (Figure
21) and specialized device screens (Figures 22-24),
ending with the Finish screen (Figure 27).

•

Select “Other,” then highlight “Learn” and press
ENTER. This will allow you to have NetCommand
learn the remote control signals of this new device.
After selecting “Learn” and pressing ENTER, the
screens that follow are: [Device] Learn screen (Figure
18), [Device] Advanced Learn screen (Figure 19),
Name screen (Figure 20), Connection screen, (Figure
21) and specialized device screens (Figures 22-24),
ending with the Finish screen (Figure 27).

To test the learned command, press the ENTER
button on the TV remote while the learned function
is still highlighted. The device should perform the
selected function. The device needs to be turned on
and the IR emitters properly placed for the test to be
successful (see page 32 for IR emitter placement).

5. Repeat for each function to be learned.
6. To erase a learned function, highlight the check box
for that function and press CANCEL.
7.

When the function signals have been learned, press
ADJUST
to select Next> and move to the [Device]
Advanced Learn screen.
NOTE: When learning the device’s remote control
signals, point the device’s remote control at the TV
screen.
Hint: If the device’s remote control uses a single button
for both Power On and Power Off, don’t learn the Power
Off function.

Chapter 3. NetCommand Setup and Editing

Edit NetCommand®: Add Devices, continued

to delete the current letter and move back one character
position. When in the first position, the CANCEL button
will return the name to the default name.

Figure 18. [Device] Learn screen

[Device] Advanced Learn Screen

Figure 20. Name screen

Figure 19

After learning the basic device keys, the [Device]
Advanced Learn screen allows you to learn any special
keys for your device. Most common IR remote control
signal formats can be learned by NetCommand.
A table of specialized device keys is shown in Appendix F.
You only need to learn the functions your devices respond
to and can ignore the functions that do not apply to your
device.

Connection for [Device] Screen
Figure 21

Select the TV and A/V receiver inputs to which the device
is connected. Connect only audio to the A/V receiver.
The A/V receiver may need configuring for digital audio.

Figure 19. [Device] Advanced Learn screen

Name Screen

Figure 21. Connection for [Device] screen

Figure 20

The Name screen allows you to change the default
name for each device to a custom name of up to eight
characters (including a blank space), selecting from
letters, numbers and nine different characters. Press
ADJUST or to select each letter, then press ENTER to
move to the next position. Press CANCEL on the remote

Chapter 3. NetCommand Setup and Editing

Edit NetCommand®: Add Devices, continued
The screens described below may not be necessary for your device setup. If they do not
display automatically on screen, they are not required.

VCR for Recordings Screen
Figure 22

Select the VCR to use for making analog recordings
through NetCommand or the TV Guide On Screen®
system. The VCR inputs must be connected to RECORD
OUT on the TV, which outputs analog signals converted
from digital.

Figure 23. RF Connection for Cable screen

IR Code for [Device] Screen
Figure 24

This screen only displays if an added device has the
same IR code as a previously added device of the same
type and manufacturer. You can specify the IR setting for
the new device. For example, for the second Mitsubishi
VCR you can specify the IR Code setting to VCR-B, if the
primary Mitsubishi VCR is using the VCR-A IR code.

Figure 22. VCR for Recordings screen

RF Connection for Cable Screen
Figure 23

Use the RF Connection for Cable screen to enable the
TV’s remote control to change channels on the cable box
and to enable VCR recording from the cable box. This
screen displays only when adding or changing a cable
box. If your cable box is connected to a TV antenna
input, check the RF check box. Select the TV antenna
input that is used with the cable box. Select the channel
number used for output by your cable box from the
choices listed (003, 004, 005); you can now change
channels on the cable box using the TV’s remote control.
If the cable box is also connected to a VCR for recording,
select that VCR.

Figure 24. IR Code for [Device] screen

If your cable box is connected using audio/video or
component cables, make sure the RF check box is
unchecked. Then the next screen will be Connection
(Figure 21), to allow selection of the TV input used with
the cable box.

Chapter 3. NetCommand Setup and Editing

Edit NetCommand®: Change or Delete Devices

Change Device Screen

Finish Screen

Selecting Change from the Setup menu screen displays
the Change screen. To change a device, select the device
by name, not type. You can change the name or input
connections to the TV and A/V receiver. If “Other” was
selected for the manufacturer then you can also “Learn.”
The rest of the screens that follow are the same as when
you Add a device.

To finalize your selections and complete the NetCommand
setup, select Finish from the Finish screen.

Figure 25. Change screen

Figure 27. Finish screen

Figure 25

Figure 27

Note: To change any of the inputs or names for the
devices, or add devices not included in the initial
settings, select Edit to display the Edit NetCommand
menu.

Delete Device Screen
Figure 26

Selecting Delete from the Setup menu displays the Delete
screen. You can choose to delete a single device by
selecting the device you would like to delete, or you can
delete the entire NetCommand configuration. After you
have chosen the device, or the entire configuration, you
will be prompted to confirm your choice to delete. If you
select the Entire Configuration, the Initial button becomes
available on the Edit NetCommand screen. If you delete a
device that you learned the remote control signals for the
learned signals are erased.

IMPORTANT

NetCommand does not allow you to delete
a device or change the connections for a
device (like a VCR or a DVD player) if the
device (input) is currently being displayed by
the TV.
Switch the TV to a different device from the
one you are changing or deleting. To change
the A/V receiver, you need to be listening to
the TV speakers.

IMPORTANT

Figure 26. Delete screen

Chapter 3. NetCommand Setup and Editing

NetCommand must be set up and the IR
emitters properly placed for your cable box
and VCR so the TV Guide On Screen system
can control these devices.

IEEE 1394 Devices and NetCommand® Control

See pages 33 and 34 for information regarding compatible IEEE 1394 devices and connection styles. The TV is not able
to control IEEE 1394 devices that use other types of control protocols. Incompatible digital audio, video and/or control
information will still be able to pass from one device through the TV to another device on the network. These incompatible
devices may not appear on the Device Selection menu or in the Review screen of the Edit NetCommand menu.

NetCommand Control of Digital Devices Using the “Learn” Feature.

Some IEEE 1394 devices, such as cable boxes or satellite receivers, will not have compatible digital control signals
or require the use of the device’s own remote control. Some of these IEEE 1394 devices will not display on-screen
information through the IEEE 1394 connection and will require using an analog connection for on-screen displays. In
many cases, to control these digital devices, the Learning feature of NetCommand can be used.
1.

Place an IR Emitter for NetCommand in front of the device’s remote control sensor (see IR Emitters, page 32).

2. On the Name for 1394 Device screen (Figure 29, page 54) use ADJUST and ENTER to check mark the Analog
Connection box.
3. Select the device type on the IEEE 1394 Device Type screen (Figure 30, page 55) of SAT or similar tuning device
4.

If desired, using the ADJUST buttons enter a custom Name on the Name screen (Figure 20, page 50).

5. At the Device screen, Select “Other” as a manufacturer and then highlight “Learn” and press Next (Figure 31, page
55).
6. Follow the device learning instructions found on the screen(s) or in the Edit NetCommand section of Chapter 3.
7.

The Connection screen (Figure 32, page 55) follows the learning screens. If analog connections are used, select the
correct inputs. If only digital connections are used, do not check the video or audio boxes.

8. Proceed with the Finish screen.
This will allow NetCommand to use the learned remote control signal to control these IEEE 1394 devices.
Note: When using the NetCommand learning feature for IEEE 1394 devices that do not have analog connections,
the GUIDE function will require pressing GUIDE twice. The first press of GUIDE will display the TV’s digital channel
guide. The second press will display the program guide for the device if an IEEE 1394 Guide is available.

Chapter 3. NetCommand Setup and Editing

Adding IEEE 1394 Devices Automatically

Adding IEEE 1394 Devices
Automatically

Name for 1394 Device Screen

Addition of IEEE 1394 devices is a special case of
NetCommand setup because the devices are detected
automatically. You review, edit, and delete these devices
through NetCommand just as you would any other
devices.

If you choose to add the discovered IEEE 1394 device,
the Name for 1394 Device screen appears. Enter a new
name for the device or use the default name that appears
automatically. The name used in this screen is the name
that appears in the Device Selection menu.

When you connect an IEEE 1394 device to the TV network
and power it on, the new device automatically announces
its presence. This process is called device discovery and
can take up to one minute.

The DV option applies only to digital camcorders at
this time and is typically detected automatically by the
TV. If your camcorder uses DV formatting but the box is
unchecked, add the check mark manually.

Some non-audio/video or incompatible IEEE 1394 devices,
such as personal computers (PCs), may not announce
their presence to the TV. The TV is not able to show these
devices in the Device Selection menu. They can, however,
coexist and are still available to other devices on the IEEE
1394 network that are compatible with these non-audio/
video devices.

To use the analog capability of some IEEE 1394 devices,
such as some DVCRs and cable boxes, check the Analog
Connection box.
• Some DVCRs, for example, can record and play
as VHS or S-VHS in addition to D-VHS. This
allows you to play analog rental tapes or analog
tapes from your established library or to make
analog recordings from an antenna or cable
system.
• Some cable boxes with IEEE 1394 connections
require an analog connection for on-screen
guides and emergency notices.

Try using the Cable/SAT/DTV position of the TV remote
control to see if it can control operation of IEEE 1394
cable boxes and satellite receivers. If not, use the remote
control that came with the device.

New 1394 Device Screen
Figure 28

Figure 29

Note: You never need to check both the DV and Analog
Connection check boxes for a device.

When your TV discovers a new IEEE 1394 device, the
New 1394 Device screen appears. Select “Add” or “Do
Not Add” depending on whether or not you want the
device added to the Device Selection menu. If the IEEE
1394 device does not provide audio and video, you may
not want to add that device to the TV’s Device Selection
menu. Devices that were discovered but not added to
the Device Selection menu will still be listed in the Review
screen of the Edit NetCommand® menu.

Figure 29. Name for 1394 Device screen

Figure 28. New 1394 Device screen

Chapter 3. NetCommand Setup and Editing

Adding IEEE 1394 Devices Automatically, continued

IEEE 1394 Device Type Screen

Connection Screen

If the new IEEE 1394 device is also connected using
analog inputs, you will need to define the device type.
Select the type of device, such as a VCR.

Select the TV input that you used when you connected
the video or S-Video cables. You may also select the TV
or A/V receiver input you used when you connected the
stereo audio cables.

Figures 30 and 31

Figure 32

The playback and record control of some devices may
still operate via the IEEE 1394 cable automatically, even
though you must use the video or S-video cable for the
picture. In this case, when you select the device, be sure
to select analog (not digital) from the pop-up that opens
when the device is selected from the Device Selection
menu. With this setup, the picture is shown via the
analog connection but control is through the IEEE 1394
connection.
Figure 30. IEEE 1394 Device Type screen
Once the device type is selected, then the Device screen
is displayed so the manufacturer can be selected. If the
manufacturer is listed, then you may be able to control
this device while it is operating as an analog VCR. For
example, if the IEEE 1394 device you have added is
a Mitsubishi DVCR, and you have selected an analog
connection as a second connection, then you will select
Mitsubishi for the manufacturer. If the manufacturer is
not listed, select “Other” and use the Learn screens
Be sure to place an IR Emitter in front of the remote
control sensor, just as you have done for other
NetCommand® devices. It is necessary to use the IR
Emitter only when the DVCR is being used as an S-VHS
or VHS VCR. When the DVCR is playing or recording
digital signals in D-VHS, the TV will control the VCR
through the IEEE 1394 cable.

Figure 32. Connection screen

Finish Screen
Figure 33

To finalize your selections and complete the
NetCommand setup, select Finish from the Finish
screen.

Figure 31. Device screen
Figure 33. Finish screen

Chapter 3. NetCommand Setup and Editing

Chapter . . .

NetCommand® Functions
Device Selection Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Device Menu Button to Display Menus.. . . . . . . . . . .
Using the GUIDE Button to Display ChannelView™ and Menus. .
NetCommand®-Controlled Recordings. . . . . . . . . . . . . . . . . .
Peer-to-Peer Connections.. . . . . . . . . . . . . . . . . . . . . . . . . . .
Using A/V Discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.
.
.
.
.
.

58
59
60
61
63
64

Device Selection Menu
When you press DEVICE on the TV’s remote control, the Device Selection menu (Figure 1) displays. If NetCommand®
has not been set up, the Device Selection menu allows you to select an input for viewing. If NetCommand is set up, the
Device Selection menu allows you to select the device for viewing, select audio from the TV speakers or A/V receiver,
power compatible devices On or Off, and verify the destination of signals. On the Device Selection menu, the device or
input currently displayed appears as a gold-colored icon.

Video
Section

Connection
Section

Device
Section

Audio
Section

Audio Section
When a NetCommand pre-memorized or learned IR
controlled A/V receiver has been connected to the TV
and added to NetCommand Setup, an AVR icon will
appear in the audio section. Press AUDIO to change
navigation to the audio section. Then press ADJUST
to select the TV speakers icon or the A/V receiver
icon. Press ENTER to change the audio selection. Press
DEVICE to return the navigation to the Device Section.

PIP Device Selection Menu
Figure 2

Figure 1. Device Selection Menu with NetCommand
Power On/Off Devices
Devices that have separate On and Off remote control
buttons will power On automatically when you select
the device and will power Off when you turn off the TV.
For devices that do not power On or Off automatically,
display the Device Selection menu, press ADJUST
or to highlight the device icon and press POWER on
the remote control. For the A/V receiver, press AUDIO
to move the navigation to the Audio Section. Highlight
the A/V receiver icon and press POWER. If you press
POWER on the remote control when the Device Selection
menu is not displayed, the TV will turn Off.

The PIP Selection menu displays when you press the PIP
DEVICE button on the remote control. This menu has the
same general format as the Device Selection menu. The
source for the Video Section is the sub picture and the
Audio and Connection Sections are not available.
Use ADJUST
to move the highlight to the
device to show in the PIP or POP screen, then press
ENTER. Device icons that are grayed out are not
available for use as PIP or POP sources or with the
current source.
Video
Section

Device
Section

Device Section
To select another device or input, press ADJUST
on the TV’s remote to move the highlight. Press ENTER
to select the device to view and hear. The TV inputs are
automatically changed. If NetCommand is set up, the
inputs on compatible A/V receivers are automatically
changed at the same time.
Video Section
The destination of the device highlighted in the Device
Section is displayed here as a TV icon.
Connection Section
The Connection Section shows the recording in progress
and the device that is recording from the source. For
example, if the Digital VCR (D-VCR) is currently recording,
when you move the highlight to the Ant-1 icon, the D‑VCR
icon appears in the Connection Section. This icon
disappears when you move the highlight to another icon
or press CANCEL to stop recording.

Chapter 4. Netcommand Functions

Figure 2. PIP Device Selection Menu

IMPORTANT
If a device does not respond to separate
On or Off remote control signals, the
manufacturer has not provided that ability
for the device.

Using the Device Menu Button to Display Menus

Device Menu

If the input is a VCR or DVD, and NetCommand is set up,
press DEVICE MENU once to display the transport menu
for the current device (figure 3). Press DEVICE MENU a
second time to display the menu for the current device
source, if available.

Figure 3. Transport menu
When used with the TV Guide On Screen, DEVICE MENU
displays or removes TV Guide’s menu information. See
the TV Guide On Screen Interactive Program Guide
User’s Manual for detailed information.
IR Controlled Devices
For a NetCommand compatible traditional IR controlled
device, pressing DEVICE MENU once or twice will display
the menu for that device. While the menu for the device
and ENTER to
is displayed, press ADJUST
navigate the screen. For some NetCommand traditional
devices, you will also be able to use the number buttons
and other additional buttons on the TV remote. For
traditional DVD players, DEVICE MENU is also known as
the setup menu.

screen shown is an example of the type of screen that
may display. Specific screen menus are sent by your
cable provider.
If there are technical problems with the CableCARD, an
error screen will automatically display with information
that may be needed by your Cable provider when you call
them for assistance.
Moving Through Other CableCARD Screens
In addition to CableCARD menus, other CableCARD
application screens may display and require you to make
additional selections. While CableCARD application
screens are customized in each area, some general rules
apply in using these screens on your Mitsubishi television.
1.

Blue text denotes a link to another screen. Press
ENTER to move to the next application. When
screens do not have blue text, there are no more links.

2. You cannot move backward through the links. If you
want to exit the CableCARD system, press HOME to
exit and return to TV viewing. CANCEL may not work
with some CableCARD screens.
All information on these application screens is provided
by your local cable company. Please contact your cable
provider if you have any problems with the application
screen displays.

CableCARD™ Menu
Figure 4

Press HOME key to exit

Figure 4. Possible Device Menu for CableCARD
When using a CableCARD, pressing DEVICE MENU will
display a list of up to 8 links to applications that contain
basic CableCARD information made available from your
cable provider. Press ADJUST or to move through
the application links. To select a link (blue text) to an
application, press ADJUST or to highlight the link,
then press ENTER to access the linked page. Pressing
DEVICE MENU will return to the CableCARD menu
screen and pressing HOME will return to TV viewing. The

IMPORTANT
Most CableCARD screens show only status
or diagnostic information and do not allow
you to make changes. These screens are
meaningful only to your local cable provider.

Chapter 4. Netcommand Functions

Using the GUIDE Button to Display ChannelView™ and Menus
The GUIDE Button

Please refer to the separate TV Guide On Screen® User’s Guide for details about using the GUIDE button with TV
Guide On Screen. When you are not using the GUIDE for the TV Guide screens, pressing GUIDE allows you to see
NetCommand® controlled program guides or menus.

GUIDE and Devices (1394 or IR Controlled)

For NetCommand-compatible satellite receivers and
some cable boxes, GUIDE displays the on-screen
programming guide for the receiver or cable box. Press
ADJUST
and ENTER to navigate the displayed
Guide. For NetCommand-compatible satellite receivers,
you may also be able to use the number or other
additional buttons.

Recording a Current Program
To record a current program, press REC (record) when
your program choice is highlighted on the program list
in ChannelView. A red “R” will be added after the input
name. The TV will immediately switch to the selected
channel and start recording.

For NetCommand-compatible DVD players, GUIDE
displays the DVD disc “top” menu (not the setup menu).
For A/V Discs, press GUIDE to display the Track List
screen. For IEEE 1394 devices with digital connections,
press GUIDE twice to display the device’s Guide. For
memory cards, press GUIDE to display a JPEG thumbnail
menu (video) or a playlist menu (audio).

GUIDE and the Device Selection Menu
For compatible traditional VCRs, press GUIDE when
the VCR is highlighted on the Device Selection menu to
change the VCR’s input.

When the A/V Receiver icon is highlighted in the Audio
Section, pressing GUIDE switches the A/V Receiver from
analog audio to digital audio and vice versa, if supported.

GUIDE and the Record To Menu

When in the Record To menu, pressing GUIDE will display
the current list of programmed recordings. Please see
Record List, page 62 for more information.

Figure 5. ChannelView screen, current programs
Recording Future Programs
To record a future program, press ADJUST
or to
select the channel you want to record from. For detailed
program information, press ADJUST , to return to basic
information press ADJUST . Press REC (record) when
your choice is highlighted. A red “R” will be added after
the input name. The message, The recording has been
added to the Record List will display. To view, change or
cancel a recording, use the Record List (page 62).

GUIDE and ChannelView
Figures 5 and 6

ChannelView is available for antenna inputs not
associated with TV Guide. Press GUIDE while viewing
ANT-1 or ANT-2 to display a list of available memorized
digital channels (D) and analog (A) channel information
(if available from the broadcaster). This list is called
ChannelView™
ChannelView for digital channels will show the major and
sub-channels (or bitstreams). Analog channel information
will display as sent. Press ADJUST or to scan
through all the channels in memory one by one. To cycle
through the choices quickly, press CH or .
For detailed program information, press ADJUST ,
to return to basic information press ADJUST . This
information is sent by the broadcaster. If limited data
is shown or no program data appears, it is because the
broadcaster is not sending the information. This is not a
defect of your TV.

Chapter 4. Netcommand Functions

Figure 6 . ChannelView screen, future programs

IMPORTANT
For complete ChannelView information to be
refreshed daily, the TV must be powered Off
from 5 to 15 minutes a day, depending on the
number of channels in memory. If the TV loses
power, the program listings will be temporarily
lost.

NetCommand®-Controlled Recordings

Setting up Recordings

Record List

Through NetCommand, you can automatically start and
stop recordings and send signals from one playback
device to a recording device. Recordings can be made
on recordable devices connected to the TV.

Press GUIDE while viewing the Record To screen to see a
list of all currently programmed recordings. A maximum
of 32 recordings can be scheduled.

Figure 7

The TV can convert digital channels and IEEE 1394
device signals to analog signals that can be recorded on
NetCommand-compatible analog VHS and S-VHS VCRs.

Figure 8

To cancel a recording on the Record List, press ADJUST
or to select the recording, then press CANCEL. To page
through the list, press CH
or .

You can schedule the recording to take place at a later
time and program the recording duration for a minimum
of 30 minutes and a maximum of six hours (in 30-minute
increments). The default is one hour. During the
recording, you can view a different device or power off
the TV.

Figure 7. Recording Setup screen

Recording Now

Can be used when viewing Antenna 1 or 2, an IEEE 1394
device, or a non-recording traditional device.
To initiate recording now:
1.

Press REC (record) on the TV remote.

2. In the “Record to” section, review the destination
device and duration. Use ADJUST or to change,
if necessary.
3. Press a second time and the recording will start.

Time-Delayed Recording
1.

Set the TV to the source you want to record.

Press REC (record) on the TV remote.

3. Press ADJUST or to select the Record To device,
duration time, start time (press ENTER after selecting
hour, minutes and AM or PM to set the time) and day,
using ADJUST or to change. For devices that
can select channels, select the channel.
4. Select Add and press ENTER to add the recording
to the record list. If your selection is successful, a
confirmation message will be displayed. If you pick
overlapping times, day(s), or destination devices, you
will see a message stating there is a conflict.
5. To exit, press HOME on the TV remote after all
recordings have been added.

Figure 8. Record List screen

Direct VCR Recording from an
Antenna or Cable Source

When your VCR is the current device, REC (record) on
the TV’s remote control functions the same as the record
button on the VCR’s remote control or front panel.

To record directly from antenna or cable:
• Method 1
1. Press DEVICE on the TV’s remote to display the
Device Selection menu. Highlight the traditional
VCR and press POWER to turn on the VCR. If
necessary, press GUIDE to select the input the
VCR is on, such as Antenna input (or line input).
2. Press ENTER to switch the TV to the VCR.
3. Select the correct channel for recording on the
VCR and then press REC to start recording. You
will need to manually stop the recording at the
end of the program
•

Method 2
With the VCR as the current recording device, press
the DEVICE MENU button to display the VCR’s menu,
in which you can schedule a delayed recording
directly from antenna or cable.

To record from ANT-1, ANT-2 or other devices, see
NetCommand Controlled Recordings or refer to the TV
Guide On Screen® User’s Guide.

Chapter 4. Netcommand Functions

NetCommand®-Controlled Recordings, continued

Copy-Protected Material

When attempting to record copy-protected material, the
Record functions of the NetCommand and IEEE 1394
systems may be prevented or stopped. If you have a
recording that is tagged “Record Once,” NetCommand
will change the tag to “Record No More.”

Restrictions for Traditional VCRs
•

Your VCR should be connected directly to the
RECORD OUTPUT AUDIO and VIDEO outputs.

•

The VCR must be set manually to “Line Input.”
Display the Device Selection menu, highlight the VCR
and press GUIDE to change VCR inputs.

•

If NetCommand is set up, the TV can select channels
on compatible cable boxes for recordings. Leave the
cable box turned on.

•

If the source device or recording device does not have
separate power On and Off features, then leave that
device powered On.

•

You cannot record from source devices connected to
the TV Component inputs or HDMI 1 or 2 connections.

Chapter 4. Netcommand Functions

Peer-to-Peer Connections

What is a Peer-to-Peer Connection?
Figure 9

A peer-to-peer connection allows the IEEE 1394 devices
in your TV network to talk to each other without the further
need of TV intervention once the peer-to-peer connection
is established. With the connection established, you can
turn off the TV or use it to watch another device.
For example, the TV can set up a connection for an IEEE
1394 cable box that sends a program to another device
for viewing. NetCommand establishes the connection
between the two devices. Set up a recording over a
peer-to-peer connection the same as you would any other
NetCommand-controlled recording.
NOTE: Analog or traditional (non-digital) devices can
not be used for peer-to-peer connections.

Figure 9. Recording Setup screen for peer-to-peer
connection

Setting up a Non-Recording
Peer-to-Peer Connection

To establish a peer-to-peer connection:
1. Select the source in the Device Selection menu.

2. Press RECORD or CONNECT on the TV remote
control to open the Recording Setup screen.
3. In the “Record To” section of the Recording Setup
screen, review the destination device and duration of
the connection. Change if necessary.
4. Press RECORD or CONNECT a second time to
establish the connection.
NOTE: Multiple peer-to-peer connections can
operate simultaneously, sometimes with the same
source device. Please note that peer-to-peer
connections are NOT listed on the Record List
screen.

Cancelling a Peer-to-Peer Connection
To cancel a peer-to-peer connection:

1. Press DEVICE to open the Device Selection menu.
2. Highlight the source device in the Device Selection
menu.
3. Confirm that the on-screen icon for the peer-to-peer
connection is in the Connection Section next to the
TV icon
4. Press CANCEL.
The peer-to-peer connection ends and the destination
icon is removed. If there is more than one peer-to-peer
connection for the same device, all the connections are
cancelled.

Chapter 4. Netcommand Functions

Using A/V Discs

A/V Disc Search

NetCommand is able to search to a specific time in a
recording on an IEEE 1394 A/V Disc.
1. Start the desired track’s playback on the A/V disc.
2. Use the number buttons to enter the time code
position of hours followed by minutes. For example,
to enter one hour and twenty-two minutes (1:22) into
the track, enter 1, 2, 2.
3. Press ENTER to skip to the time code position.
4. To cancel the request or to start over, press CANCEL
instead of ENTER.

Track List Screen
Figure 10

When viewing an A/V Disc, press GUIDE to display its
Track List. The time and date it was added, the duration
and title will be displayed. Tracks will be listed in date and
time order and will vary in size. Press ADJUST or to
navigate through the Track List. To play a track, select it
on the list, then press ENTER. To change pages, press
CH or . To delete a track, select it on the list and
press CANCEL.

Figure 10. Track List screen

Chapter 4. Netcommand Functions

Using the Remote Control with an A/V
Disc after Selecting It from the Device
Selection Menu:
GUIDE:

displays the Track List of recorded programs.

INFO:

•
•

from within the Track List: displays program
description.
from outside the Track List: displays A/V disc
status.

PLAY:

resumes playback of paused program.

PAUSE:

pauses or resumes playback of program.

FF/FWD:

forward picture search, multiple presses increase
the speed.

REW/REV: reverse picture search, multiple presses increase
the speed.
ADJUST : skips backward 12 seconds per press.
ADJUST : skips forward 30 seconds per press.
ADJUST

: skips to the end of the track.

ADJUST

: skips to the beginning of the track.

REC:

displays the Record Menu to schedule recordings.

CANCEL:

deletes a highlighted track.

CH Up/Dn

pages through multiple screens of listed tracks.

Chapter . . .

TV Menu Operations
Main Menu.. . . . . . . . .
Setup Menu . . . . . . . .
NetCommand® Menu .
Record Menu.. . . . . . .
Channel Menu .. . . . . .
Captions Menu.. . . . . .
V-Chip Lock Menu. . . .
Audio/Video Menu. . . .
Audio Settings. . . . . . .
Video Settings. . . . . . .

.
.
.
.
.
.
.
.
.
.

66
67
69
70
72
74
76
79
80
81

Main Menu

Setup Menu

Channel Menu

Use the Setup menu to select English or Spanish as
the language for the menus and on-screen displays.
Memorize the available channels for antennas or cable
connected to the ANT-1 and ANT-2 inputs. Manually
set the time for the TV, or select Auto and the TV will
automatically set the time based upon Extended Data
Service (XDS) time data. This time data is usually
broadcast by your local PBS station. This menu is also
used to set the TV timer, and reset the lamp reminder.
The TV’s software version is displayed on this screen.

Edit channels for ANT-1 and ANT-2. After memorization,
if a channel displays as digital and analog, you can
choose to see the channel digitally every time it is
selected. Manually add or delete channels from memory,
name channels or add your favorite channels to a SQV
(SuperQuickView™) list. Displays signal strength of
currently tuned digital channels.

Figure 1

Figure 4

Figure 4. Main menu, Channel selected

Captions Menu
Figure 5

Figure 1. Main menu, Setup selected

NetCommand Menu
Figure 2

Add, change, review or delete NetCommand® settings
and devices. Enable/disable TV Guide On Screen® or
change ZIP code and input selection settings. Change
the order of icons on the Device Selection menu. Turn the
transport menu off.

Display Closed Captions if sent by the broadcaster,
select settings for analog or digital captions.

Figure 5. Main menu, Captions selected

V-Chip Lock Menu
Figure 6

Block or allow programing based upon rating signals sent
by the broadcast station, lock by time, or lock the front
panel buttons.

Figure 2. Main menu, NetCommand selected

Figure 6. Main menu, V-Chip Lock selected

Record Menu

Audio/Video Menu

Set up and view recordings and recording defaults. View
your customized Record List. If you have more than one
digital recording device connected, use this menu to
change the default digital Record To device. Set analog
recording size.

Reset the A/V Memory to return to the original factory
A/V settings for a selected device. Customize the
individual audio and video settings. Display a blue
screen when viewing a device with no signal, enable/
disable Film Mode, or turn the TV speakers on or off.

Figure 3. Main menu, Record selected

Figure 7. Main menu, Audio/Video selected

Figure 3

Chapter 5. TV Menu Operations

Figure 7

Setup Menu

Setup Menu
Figure 8

After memorizing channels, the channels in memory
can be accessed in ascending or descending order by
pressing CH or . Select the Channel Menu to access
further channel-editing features, such as channel add or
delete, channel name, and SQV custom favorite channel
memories.
When you use a CableCARD™, the complete list of
available channels is provided through the CableCARD.
As a result, the Ant-1 channel-memorization options are
not available and are shown grayed out on the screen.

Figure 8. Setup Menu

Language

Display the on-screen menus in either English or Spanish
(Español). The first time you powered on your TV, you
were requested to select an on-screen-menu language.
If you choose to change the selection, all menu text will
immediately switch to the language of your choice.

In the TV Guide On Screen® system, the channels
displayed and the order in which they are displayed in
the Guide is independent of the channel-memorization
process. Refer to the TV Guide On Screen Interactive
Program Guide User’s Manual for detailed instructions
on editing channels shown in this guide.

Clock
Figure 9

To listen to audio in other languages (when available), see
the section of this Owner’s Guide covering audio settings.

You may choose to manually or automatically set
the clock that your TV will use for recording or timer
functions.

Memorize Channels

Manual
To manually set the clock, you need to select the
current time, current date, time zone for your area and
the Daylight Savings time setting.

For Antenna 1 (Main) or Antenna 2 (Aux)
To start channel memorization, first select an input
according to the table below.
Input

Condition

Ant-1 Air

When connected to an indoor/
outdoor antenna

Ant-2 Air
Ant-1 Cable
Ant-2 Cable

When connected to direct cable

Press ENTER to start the automatic channel-memorization
process. The memorization process is started separately
for each antenna selection.
During the memorization process, all possible channels on
the selected antenna are scanned twice. Analog channels
are scanned first and then the process is repeated for
digital channels.
To stop the automatic channel-memorization process
before it completes, press CANCEL. Channels
memorized before you pressed CANCEL are retained in
memory. If you start the memorization process again, all
previously memorized channels for the selected antenna
input are erased and the process starts over from the
beginning.

Figure 9. Time Menu, Setting the Clock Manually
Time
Press ADJUST or repeatedly to slowly select the
hour or press and hold to quickly select the hour. Press
ENTER to move to the minutes options. Press ADJUST
or to select minutes.
Date
Press ADJUST

to select the correct date.

Chapter 5. TV Menu Operations

Setup Menu, continued

Time Zone
Select your correct time zone. Press ADJUST or to
select the time zone (Atlantic, Eastern, Central, Mountain,
Pacific, Alaska or Hawaii) for your area. Then press
ADJUST
to move to the Daylight Savings time option.
Daylight Savings Time
Select the Daylight Savings time (DST) option that your
state uses. Press ADJUST or to select Applies if your
state or area uses DST, or Ignore if DST does not apply.
Auto
Select the Time Zone and Daylight Savings time setting,
as noted above. You may then tune to a channel (on
ANT-1 or ANT-2) that uses Extended Data Service (XDS)
time data, typically a PBS channel. The Auto selection
will automatically retrieve the correct time and date
information from this channel. Be aware that if a channel
displays incorrect time information, it is because of
information sent from the broadcaster and is not a defect
of the TV.

Timer

Figure 10

On/Off
The timer allows you to set up a time when the TV will
change the channel and turn on. You select the time and
day for the TV to turn on and the device and channel to
display. At your preselected time, the timer will turn the
TV on and this message will be displayed: “Press a button
for the TV to stay on.” Press any button on the remote
control within five minutes or the TV will turn itself off.

Figure 10. Timer Menu (Timer On/Off)
Set Day
Select the day or days that the TV will turn on
automatically. Press ADJUST or to select Daily,

Chapter 5. TV Menu Operations

Mon-Fri (Monday through Friday), or the individual days of
the week.
Set Time
Press ADJUST repeatedly to slowly select the hour or
press and hold to quickly select the hour. Press ENTER
to move to the minutes options. Press ADJUST or to
select minutes.
Device
Press ADJUST or to select the device to use when
the timer turns on the TV. If the TV is already on, the
timer will turn the TV to this selected device.
Channel
When an antenna is the selected device, you may select
any memorized channel. Press ADJUST or to
select the channel and the TV will tune to this channel
in memory when the timer turns it on. This includes
sub-channels for digital choices.

Lamp Reminder

Select to reset the lamp reminder message after you have
changed the lamp cartridge. Press ENTER to reset the
lamp reminder. To have an accurate reminder that the
lamp cartridge may soon need replacement, reset the
lamp reminder only when you replace the lamp cartridge.
See Appendix H for detailed information about changing
the lamp.

Software Version

For some service-related issues, it may be necessary to
know the software version in your TV. This information is
displayed on the Setup menu screen.

NetCommand® Menu

NetCommand Menu
Figure 11

Transport Menu
Figure 13
$"#-&%#4%57 7$3 %7%
"6%*0
57

Figure 13. Transport Menu

108&3

NetCommand uses the Transport menu to control VCRs,
VCRs,
and similar
DVDs, IEEE 1394 A/V Discs, digital
devices. If you choose to turn off
this menu when
viewing
27
427

the devices, the transport buttons (rewind, play forward,
stop, pause and record) on the TV’s remote control will
continue to operate these devices. In the Device Selection
menu selecting a VCR or DVD Player will automatically
display the Transport menu. You can re-display this menu
by pressing DEVICE MENU. 57.&/6
(6*%&
46#$"/$&-

Figure 11. NetCommand Menu

Edit

Detailed information regarding setting up and editing
the NetCommand menu is found in Chapter 3. The Edit
NetCommand screens allow you to add new devices and
change traditional and IEEE 1394 devices. You can also
set up the TV Guide On Screen® system or turn it on
or off. Turn devices and unused inputs On or Off, delete
a single device or delete the entire setup configuration.
If you choose to delete the entire configuration, or if
the NetCommand setup was cancelled, deleted or not
completed, you can start at the Initial NetCommand
screen. The Review screen shows all devices connected
to the TV.

Icon Order
Figure 12

The Icon Order screen allows you to arrange the device
icon order on the Device Selection menu to a different
sequence, for ease of selection and operation.

%&7*$&

.65&

70-

1"(&

Select Transport menu functions by pressing ADJUST
%&7*$&
, , , and then ENTER. For
example, to pause
.&/6
)0.&
playback, press ADJUST or to move to PAUSE, then
press ENTER. If a function is not7$)*1
possible,
such
as
record
7*%&0
"6%*0
*/'0
for a DVD Player, the Transport menu button will be grayed
&9$)
1*1101
1*1$)
4-&&1
out.

Remote Control Transport Buttons
1*1%&7*$&

Transport buttons (rewind,
play forward, stop, pause
and record) on the remote
control are located in the
bottom section of the
remote control.

'03."5

3&$

$0//&$5

1"64&

1-":
'''8%

3&83&7

4501

To change the order, press ADJUST , , , to
highlight the icon to be moved and then press ENTER.
Press ADJUST , , , to move the icon to the desired
position and then press ENTER to select the icon.

Figure 12. Icon Order Menu

Chapter 5. TV Menu Operations

Record Menu

Record
Figure 14

The Record menu allows you to set up recordings, view
the record list, and set defaults for your recording devices.

You cannot record from an analog channel or device or a
VHS or S-VHS VCR to a digital recording device such as
a DVCR or A/V Disc.

Figure 15. Recording Setup screen
Recording Now
Can be used when viewing Antenna 1 or 2, an IEEE 1394
device, or a non-recording traditional device.
Figure 14. Record Menu
Recording Setup
Figure 15

The recording Setup screen is where you tell the TV what,
where, and when to record. There are two ways to open
the Recording Setup screen:
• select Record from the Record menu.
• press REC on the remote control when viewing a
recordable source.
Your TV can stop recordings automatically and it can
send the signals from one external playback device
to another external recording device. It is also able to
convert digital channels and IEEE 1394 device signals to
analog signals. These converted signals can be recorded
on NetCommand-compatible analog VHS and S-VHS
VCRs connected to the RECORD OUTPUT/VIDEO and
AUDIO outputs on the back of the TV.
You can schedule the recording to take place at a later
time and program the recording duration for a minimum
of 30 minutes and a maximum of six hours (in 30-minute
increments). The default is one hour.
When a digital recording is being made, the TV can direct
the signals to the recording device using the IEEE 1394
cable. In the case of an analog recording, (as to a VCR)
the TV converts the digital signals to analog format and
sends the analog output to the VCR through the RECORD
OUTPUT jacks.
During the recording, you can view a different device or
power off the TV. See Appendix I for more information.
To prevent recording of unwanted material while recording
to a VCR or A/V disc, press PAUSE to temporarily stop
recording. Press PAUSE again to resume recording.

Chapter 5. TV Menu Operations

To initiate recording now:
1. Press REC (record) on the TV remote or press
ENTER if the Record menu is displayed.
2. Review the Record To (destination) device (VCR) and
duration. Change if necessary.
3. Press REC a second time to initiate recording.
Time-Delayed Recording
To initiate a time-delayed recording:
1. Set the TV to the source you want to record.
2. Press REC (record) on the TV remote or press
ENTER if the Record menu is displayed.
3. Press ADJUST or to select the channel, device
to record to, duration time, start time (press ENTER
after selecting hour and minutes to set the time) and
day.
4. Select Add and press ENTER to add the recording
to the record list. If your selection is successful, a
confirmation message will be displayed. If you pick
overlapping times, day(s), or destination devices, you
will see a message stating there is a conflict.
5. To exit, press HOME on the TV remote after all
recordings have been added.
IMPORTANT
See Appendix I for a list of recording and
viewing combinations available for this TV.
IMPORTANT
Recordings scheduled on this screen are
independent of recordings scheduled through
TV Guide On Screen®. Recordings scheduled
with TV Guide On Screen have priority if
there is a conflict between the two recording
schedules.

Record Menu, continued

Record List
Figure 16

To see a list of all currently programmed recordings, select
the record list option on the Record menu or press GUIDE
while viewing the Recording setup screen. A maximum of
32 recordings can be scheduled. To page through the list,
press CH or .
To Cancel Scheduled Recordings
To remove a recording from the record list, use or
to highlight the scheduled recording and then press
CANCEL.
To Cancel a Recording in Progress
1. Press DEVICE to display the Device Selection menu.
2. Highlight the icon for the source device and verify
that the icon for the recording device apears in the
connection section.
3. Press CANCEL

A digital recording can be made on either a digital or
analog device. For best playback quality, however,
record digital programs on a digital recording device.
Not that analog recordings can only be made on the one
analog device connected to RECORD OUTPUT (usually a
VCR) and are not affected by this setting.
If multiple devices were not connected and then added
in the NetCommand setup, this setting will be unavailable
(grayed out).

Analog Recordings

When you record a 16:9 digital channel to an analog
VCR or recording device, there is a mismatch between
the picture shape of the 16:9 ratio of the source and the
narrower 4:3 ratio of the analog recorder.

•

For anamorphic playback on this widescreen TV,
choose the anamorphic picture display and ensure
that the TV screen format is set to standard (see the
section on TV formats in this Owner’s Guide).
For cropped playback on an older style 4:3 TV,
choose the cropped display to remove the top
and bottom sections. This setting does not affect
recording from analog devices, analog channels, or
4:3 digital channels.

Setting Up Analog Recordings with TV
Guide On Screen®
When setting up a recording using TV Guide On Screen,
note that:

Figure 16. Record List screen

•

You must select the desired recording device in the
TV Guide On Screen Record Options menu.

TV Guide On Screen® and the Record
List

•

Analog programs can only be recorded to an analog
recording device, such as a VCR.

•

Analog programs cannot be recorded to digital
devices such as A/V discs or DVCRs.

•

The destination recording device for analog programs
must be the analog device connected to the TV’s
RECORD OUTPUT jacks.

Programs scheduled through TV Guide On Screen do not
appear on this record list. Refer to the separate TV Guide
On Screen® User’s Guide for information regarding
scheduling recordings with TV Guide On Screen.

If there is a conflict between recordings scheduled
through TV Guide On Screen and the Record List, the TV
Guide On Screen recording takes priority.

Default Digital (Record) Device

This setting allows you to choose the default device to
use when recording digital programs using the REC key
from within ChannelView™ (page 60) or TV Guide On
Screen®. Use this option only if you have more than one
recording device set up in Netcommand.

IMPORTANT
When setting up analog recordings in
TV Guide On Screen, you must set the
destination recording device as the analog
device connected to the TV’s RECORD
OUTPUT jacks.

Chapter 5. TV Menu Operations

Channel Menu

Channel

Memory

Figure 17

After the available channels have been memorized with
Memorize Channels on the Setup menu, weaker channels
can be added or unwanted channels can also be deleted.
Press CH or on the remote control to see the
channels in memory. Press ADJUST or to select
Added or Deleted for the channel shown in the Channel
number box.

Name

Analog channels shown on Antenna-1 or Antenna-2
can be named (up to four characters). After you enter a
name, it will appear on the TV screen, next to the channel
number.

Figure 17. Channel Menu

Antenna

Select the antenna for the channels you want to edit. You
can select Ant-1 (main) or Ant-2 (Aux).

Prefer Digital

When a memorized channel number is available as both
analog and digital, a check mark in the Prefer Digital
box causes digital channels to be displayed and analog
channels to be hidden (when using CH or ). Remove
the check mark to show both analog and digital choices.
This option is not available when TV Guide On Screen® is
enabled.

Channel

Channels can be changed in three ways:

•

Press ADJUST

•

Pressing CH
memory.

•

Enter the number directly. Channel numbers can be
one part, analog or digital (up to the number 16383), or
two part for digital channels (these use a separator).
For a two-part digital channel, press SUB/CANCEL on
the remote to enter a separator after the first, second
or third number, depending on the broadcaster’s
channel information.

to select the channel.
to select channels already in

For digital channels, when the broadcaster has sent a
virtual channel number, the virtual channel number is
shown in the text box and the original digital channel
is shown below on-screen, as a reference.

Chapter 5. TV Menu Operations

Press ADJUST

to select each letter.

2. Press ENTER to set the letter and move to the
next letter position.
3. Press CANCEL to move back one position.
Digital channels are automatically named if the
broadcaster sends the information.

Channel Menu, continued

SQV (SuperQuickView™)

Removing SQV channels using the remote control:

Figure 17

Using The Menu Screen

SQV (SuperQuickView™) allows you to put together lists
of your favorite channels from Antenna 1 and Antenna
2. You can store channels in any of the 9 different SQV
memory banks. You can also store the same channel in
multiple memory banks. Once you have added a channel
to an SQV memory, “SQV” and the memory bank number
will appear under the tuned channel number on the TV
screen.
Adding SQV Channels
1. Select the channel using the “Channel” option box or
press CH or .
2. Highlight the bank (SQV1-SQV9).
3. Press ENTER to check mark the selected SQV memory
bank.
4. Repeat for additional channels or banks.
Removing SQV Channels
1. Highlight the box for the SQV bank number.
2. Press ENTER to remove the check mark.

SQV (SuperQuickView™)

Using The Remote Control
Viewing and changing SQV banks using the remote
control:
1.

Press the SQV button and then the memory bank
number.

2. Press the SQV button repeatedly until you see the
desired channel.
3. While the channel number and SQV indicator (with
correct bank number) are still displayed on the screen,
press the CANCEL button. If the CANCEL button
is not pressed before the SQV indicator disappears
automatically, the channel will not be removed.
4.

When the SQV indicator disappears, the channel
has successfully been removed only from that bank.
“Other” banks remain unchanged.

Signal Strength

Displays the approximate signal strength of the currently
tuned digital channel. Use this indicator to help you
adjust the antenna direction for optimal signal strength.
The higher the bar, the stronger the signal. Does not
apply to analog channels.
You can change the tuned channel while in this menu so
that you can see the effects of antenna adjustments. To
change the channel, either:
• Highlight the channel box, press CH
or ADJUST
to display the desired channel number, and
press ENTER.
• Enter the channel number on the remote control and
press ENTER.

Press the SQV button.

2. To change memory banks, press a number button
within 5 seconds of pressing the SQV button.
3. Press the SQV button repeatedly to cycle through the
channels available in that bank.
Adding SQV channels using the remote control:
1. Press CH , , or number buttons to select the
channel you want to add to the current SQV memory
bank.
2. Press and hold the SQV button for about 2 seconds.
When “SQV” and the memory bank number
appear under the channel number, the channel has
successfully been added.

Chapter 5. TV Menu Operations

Captions Menu

Background

Captions Menu
Figure 18

For analog channels, broadcasters can send either
Standard or Text closed captioning. Standard Closed
Captions follows the dialogue of the characters on screen
and displays in a small section of the screen. Text Closed
Captions often contain information such as weather or
news and covers a large portion of the screen.
On digital channels, broadcasters can send up to six
different captioning selections or can send analog
captions the same as the analog station sends. Each TV
station may broadcast only one or two types of captions
or none at all. The TV cannot decode Closed Captions
received on COMPONENT 1–3 or HDMI 1 or 2.

To make the analog closed captions easier to read, you
can choose to display the background color as either
black or gray behind the captions.

Digital Captions

The TV can display one of the following Captions for
Digital sources:
•

Captions 1-6. Sent by broadcaster.

•

On if Mute. Closed captions when mute. When
selected, the captioning signal (Caption 1) will turn on/
off by pressing MUTE on the TV remote control.

•

Off. No closed captions.
Note: For digital programs, if the broadcaster is
sending only analog captions converted to digital,
then the analog captions settings apply.

Appearance

Closed Captions provider selects the Default options
when sending digital closed captions. You may select
the Custom option to override and customize Closed
Captions appearance. These settings do not apply to
analog Closed Captioning converted to digital.

Figure 18. Captions Menu

Analog Captions

The TV can display one of the following captions for
Analog sources:
•

CC1, CC2, CC3, or CC4. (Standard closed captioning
signals).

•

Text1, Text2, Text3, or Text4. (Text closed
captioning signals).

•

On if mute. Closed captions when mute. When
selected, the standard closed captioning signal (CC1)
will turn on/off by pressing MUTE on the TV remote
control.

•

Off. No closed captions.

Digital Settings
Figure 19

Move the highlight to the Digital Settings icon and
press ENTER. The Digital Settings menu allows you to
customize the appearance of the closed captions sent by
the broadcaster. Digital settings do not apply to analog
closed captions converted to digital.

Figure 19. Closed Captions Menu Digital Settings

IMPORTANT
When analog text closed captioning is
selected, a large black or gray box appears
on your TV screen if no signal is broadcast.

Chapter 5. TV Menu Operations

Captions Menu, continued

Fonts

•

You can customize the text of digital captions by selecting
the font of your choice. The available font options are as
follows:
•
•
•
•
•
•
•
•

Default—Selected by the Closed Captions
provider
Font 1—Monospaced font with serifs
Font 2—Proportionally spaced font with serifs
Font 3—Monospaced font without serifs
Font 4—Proportionally spaced without serifs
Font 5—Casual font
Font 6—Cursive font
Font 7—Small Capitals font

Size

You can also customize the text of digital captions
by selecting your desired size of font. Large is the
recommended font size.

•
•
•

Translucent—TV program is faintly visible behind the
text
Transparent—See-through text reveals the TV
program
Opaque—Solid color text; blocks the TV program
Flashing—Text flashes at intervals

Background Opacity

You can customize the background for digital captions
using the following categories:
• Translucent—TV program is dimly visible behind the
background
• Transparent—See-through background reveals the TV
program
• Opaque—Solid background; covers TV program
• Flashing—Background flashes at intervals

Color

You can customize the text of digital captions by selecting
the font color. The available font colors are listed below.
Text and background cannot be set to the same color.
White
Black
Magenta
Red

Yellow
Green
Cyan
Blue

Background

To make the digital closed captions easier to read,
you can choose the background color. The available
background colors are listed below. Text and
background cannot be set to the same color.
White
Black
Magenta
Red

Opacity (Font)

Yellow
Green
Cyan
Blue

You can customize the visibility of your fonts using the
following categories:

IMPORTANT
We recommend you use contrasting colors for
captions and background. Black translucent
background combined with a white font make
and easy-to-read combination.
Use care when selecting custom colors. Your
choice may change the legibility or readability
of captions.

IMPORTANT
The content of captions is determined by the
broadcaster. If your captions show strange
characters, misspellings, or odd grammar, it is
not a malfunction of the TV.

Chapter 5. TV Menu Operations

V-Chip Lock Menu
V-Chip Lock Menu Overview

IMPORTANT

Figure 20

The V-Chip Lock menu gives you access to three different
types of TV locks. You must use a pass code to open
this menu to enable/disable the lock options. The three
different types of locks available are:
•

V-Chip
Lets you restrict access to programming based on
program-rating signals sent by the broadcaster. You
can also set the time of day for these restrictions to
be in effect.

•

Lock by Time
Lets you restrict all TV viewing by time of day.

•

Front Button Lock
Lets you disable the controls on the front of the TV.
Use this option if there are small children near the TV
who may be tempted to press the front-panel buttons.

V-Chip Icon

Lock TV by
Time

Front Button
Lock On/Off

If you forget your four-digit pass code, see
Appendix C.

V-Chip Menu
Figure 21

The V-Chip menu allows you to:
• Turn the V-Chip Lock on or off
• Change the permitted V-Chip rating level
• Set the time of day to enforce rating restrictions
The TV comes from the factory with pre-set V-Chip
ratings and with the V-Chip Lock turned off. The preset
ratings are TV-PG (TV rating) and PG (movie rating). If
you turn on the V-Chip, these presets will allow only
programs rated TV-PG/PG or lower. You can turn on
V-Chip from this menu or by using the V-CHIP button on
the remote control. Use the V-Chip menu to change the
permitted rating levels.
After changing channels or devices, there may be a delay
of up to five seconds before the V-Chip lock takes effect.

5
4

Figure 20. V-Chip Lock menu

Setting a Pass Code

You are prompted to enter a pass code whenever you
select V-Chip Lock on the menu or press the V‑CHIP key
on the remote control. To set a pass code for the first
time:
Do one of the following:
• Press V-CHIP on the remote control.
• Press TV MENU, highlight V-Chip Lock, then
press ENTER.
A screen prompting you for a pass code displays.
2. Input a four-digit pass code using the number keys on
the remote control.
• Press CANCEL to delete a number and move
back one space.
• Press MENU or HOME to exit without setting
a pass code.

Figure 21. V-Chip menu

Setting V-Chip Options
1.

3. Press ENTER to confirm the pass code just input.
To reset the pass code, see the procedure in Appendix C.

Chapter 5. TV Menu Operations

2.
3.
4.
5.

Highlight the V-Chip icon
on the V-Chip Lock
menu (figure 20) and press ENTER to open the V-Chip
menu (figure 21).
Press ADJUST or to select On or Off.
If you selected On, press ADJUST to move to the
TV Rating box.
Press ADJUST or to select the TV rating level
you want to allow.
Press ADJUST to move to the TV content
categories.
• Press ADJUST or to move between
categories.
• Press ENTER to add check marks to the TV
content categories you want to block.

V-Chip Lock Menu, continued
6. Press ADJUST to move to the Programs Not Rated
box. Press ENTER to add or delete a check mark to
allow or block programs that are not rated.
NOTE: Use care when choosing to block unrated
programming. News programs and emergency
bulletins carry the “None” or “NR” (Not Rated) V‑Chip
rating, and these are blocked with this option active.
7.

Press ADJUST to move to the Movie Rating box.
Press ADJUST or to select the movie rating level
you want to allow. See the next page for detailed
information on rating guidelines.
8. To set the time of day when these restrictions will be
in effect, press ADJUST to move to the Start box.
To set the time:
a. With the highlight on the hour number, press
ADJUST or repeatedly to change the hour.
You can also just press and hold to change the
hour.
b. Press ENTER to move the highlight to the
minutes.
c. With the highlight on the minutes number, press
ADJUST or repeatedly to change the
minutes. Just press and hold to move quickly
through the numbers.
d. Press ENTER to move the highlight to the am/
pm option. Press ADJUST or to make a
selection.
9. Press TV MENU to save the settings and close the
menu.
NOTE: To make the V-Chip restrictions active twenty-four
hours a day, set the V-Chip Start and Stop to the same
time.

The V-CHIP Button

Press the V-CHIP button on the remote control to turn the
V‑Chip lock on and off without going through the menu.
A screen will appear prompting you for your pass code.
To change V-Chip settings, you must open the V‑Chip
Lock Menu and then open the V-Chip menu.

Lock by Time

Lock by Time allows you to entirely block use of the TV
during specified hours. During the lock time, you must
use your pass code to view the TV. To lock the TV by
time:
1. Press ADJUST or to select On or Off for Lock by
Time.
2. Press ADJUST to move to the Lock Time box.
a. With the highlight on the hour number, press
ADJUST or repeatedly to change the hour.
You can also just press and hold to change the
hour.
b. Press ENTER to move the highlight to the
minutes.
c. With the highlight on the minutes number, press
ADJUST or repeatedly to change the
minutes. Just press and hold to move quickly
through the numbers.
d. Press ENTER to move the highlight to the am/
pm option. Press ADJUST or to make a
selection.
To make Lock by Time active 24 hours a day, set the Lock
and Unlock Times to the same time.

Front Button Lock
Figure 20

Front Button Lock lets you disable controls on the front
panel to prevent inadvertent changes to TV settings.
Select On to disable the buttons and select Off to restore
their operation.
To disable the front button lock, press and hold the
MENU button on the front panel for more than eight
seconds. If the TV is on, a message will display
confirming release of the Front Button Lock.

Bypassing V‑Chip Lock and Lock by
Time

If you try to watch blocked programming, a notice
appears prompting you for a pass code. To use the TV:
• Input your four-digit pass code and press ENTER.
• Change to a channel airing an allowed program or
change to another device.
If you try to use the TV when it is locked by time, a
similar screen appears, prompting you for your pass
code.
To reactivate the V-Chip lock or TV lock by time after
using the pass code, power the TV off and then on.

Chapter 5. TV Menu Operations

V-Chip Ratings
V-Chip Signal Information

When provided by the broadcaster, V-Chip ratings can be used to control which programs can be viewed or will be
blocked. When V-Chip ratings are sent, you will see the ratings when you change the channel or when you press the
INFO button on the remote control. Both TV and Movie ratings will display. TV ratings apply to programs and movies
developed for TV and may have supplemental blocking by content categories. Movie ratings use MPAA ratings for
movies released in theaters.
V-CHIP EXCEPTIONS:
1. V-Chip is not effective for programs viewed on devices connected to component inputs or HDMI.
2. Videotapes, laser discs and DVDs may not contain V-Chip rating signals. If they don’t contain the V-Chip signal,
V-Chip cannot block the program or movie.
3. Broadcasters are not currently required to include V-Chip rating signals at this time. If the broadcaster does not
include the V-Chip rating signal, V-Chip cannot block the program.
TV Ratings:
Used with TV programs and Made-for-TV movies.
TV-Y
Youth, for children under the age of 7.
TV-Y7 Youth, 7 years old and older.
TV-G
General Audience. For the entire family to view.
TV-PG Parental Guidance. Parental Guidance is recommended, may
not be suitable for some children.
TV-14
Adolescent 14 years old and older. Not recommended for
children under the age of 14.
TV-MA Mature Audience. For adults only.

TV Rating FV
TV-Y
TV-Y7
X
TV-PG
TV-14
TV-MA

X
X

X
X
X

Content Categories:
Used in association with the TV ratings above.
FV Fantasy Violence—applies to TV-Y7 only.
D Sexual Dialog—applies in different degrees to TV-PG and TV-14.
L Adult Language—applies in different degrees to TV-PG, TV-14, and TV-MA.
S Sexual Situations—applies in different degrees to TV-PG, TV-14, and TV-MA
V Violence (graphic or realistic)—applies in different degrees to TV-PG, TV-14, and TV-MA.
When you select a TV rating, you are selecting the least-restrictive program level that can be viewed. For
example, if you select TV-PG, you are allowing programs rated TV-Y, TV-Y7, TV-G and TV-PG to be seen and
blocking programs rated TV-14 and TV-MA. When you select a TV Content category, you will block all TV
programs that have the same content category listing. For example, if you select to block V (Violence) at the
TV-14 level, you will also block any program that has the V category listing at the TV-PG rating level as well.
Movie Ratings:
Used with theater released movies and direct-to-video movies.
G
General Audience—Designed for the entire family to view.
PG
Parental Guidance—Parental Guidance is recommended, may not be suitable for some children.
PG-13 Parental Guidance 13 years old and older—Not recommended for children under the age of 13.
R
Restricted—Restricted in the theater to 17 years old and older unless accompanied by an adult.
NC-17 No Children 17 or under—Restricted in theater to 18 years old and older.
X
Adult—Designed for and restricted in the theater to adult audiences only.
When you select a movie rating, you are selecting the least-restrictive program level that can be viewed. For
example, if you select a movie rating of PG-13, you are
allowing movies rated G, PG and PG-13 to be seen and
IMPORTANT
blocking movies rated R, NC-17, and X.
Programs Not Rated: Used for programs that are not rated,
such as news, sports, weather, emergency bulletins, or movies
prior to or without MPAA Ratings. This does not include
programs without V-Chip signals.

Chapter 5. TV Menu Operations

If you elect to block programs that carry the
V-Chip rating “Programs Not Rated,” you may
block news or emergency bulletins, when “None”
or “NR” Not Rated V-Chip rating is included. Use
care when blocking programming that is not
rated.

Audio/Video Menu

Audio/Video
Figure 23

When the original video was filmed on
30-frame-per-second cameras, the Auto setting
automatically applies video decoding, the same as used
with the Off setting.
Film Mode is not effective for high-definition signals.

TV Speakers

When an A/V receiver has not been set up in
NetCommand, this selection will turn the TV’s internal
speakers on or off. You may select Off when sending
the sound through a separate stereo system or surround
sound A/V receiver.

Figure 23. Audio/Video Menu

A/V Memory Reset

A/V Memory Reset allows you to reset a specific device’s
A/V settings to the original factory settings. Select the
device name in the box and press ENTER. Note that
the audio settings of Balance, Listen to, and Language
are not associated with any specific device and are
unaffected by A/V Memory Reset. To reset all A/V
settings at once, including these three, perform an A/V
Reset using the front-panel buttons.

Settings

Each device has its own A/V memory. Select the device
in A/V Memory Reset, then select Audio or Video to
adjust the device’s individual settings. Press ENTER,
and the menu is removed and the individual settings are
displayed.

Use ADJUST or to select the individual settings to be
adjusted. Use ADJUST or to make the adjustment.
For descriptions of the individual A/V settings see A/V
Setting Descriptions, pages 80 and 81.

This option is unavailable (grayed out) when
NetCommand® is enabled and you have selected the A/V
receiver icon from the Device Selection menu. In that
case, Netcommand automatically turns the TV speakers
off. See the NetCommand information for further
instructions.
Note: To prevent damage from a sudden increase in
volume, make sure the TV volume is set to low before
setting speakers to On.

Using the AUDIO or VIDEO Button on
the Remote Control

To adjust individual Audio or Video settings directly with
the remote control:
1.

Press AUDIO or VIDEO to cycle through the available
settings.

2. Press ADJUST or to adjust the setting. After
five seconds of inactivity, the setting display will
disappear.

Video Mute

Video Mute lets you display a blue background when no
signal is being received on Inputs 1–3, COMPONENT 1–3,
and HDMI 1 and 2.

Film Mode

Auto is the default setting. With Auto selected, the
TV automatically detects and applies film-decoding
correction for images that originated on
24-frame-per-second film cameras and were then
converted to 30-frame-per-second video for broadcast.
Try the Off setting if the TV adds too many jagged edges
to the images.

Chapter 5. TV Menu Operations

Audio Settings
NOTE: The effects of the audio settings of Bass, Treble, Balance and Surround affect the sound heard through the
TV speakers only.

be related to the program you are watching, (such
as a sound track in a foreign language), or it
might be unrelated (such as a weather report). If
an SAP signal is broadcast, the letters “SAP” are
displayed when you tune to the channel.
Mono: Reduces background noise. Use when
receiving a weak stereo audio signal. All audio is
played mono with this setting.

Analog and Digital Audio Settings

A slider displays on screen for most settings. When the
slider is displayed, it has a numeric value, so that 63 is
the maximum, 31 is the mid-point, and 0 is the minimum.
◊

Bass
Enhances or reduces low-pitched sound.

◊

Treble
Enhances or reduces high-pitched sound.

◊

Balance
Adjusts the level of sound between the left and right
speakers.

◊

Surround
Creates simulated stereo and surround effects
through the TV speakers. Your choices are:
• Off: No surround effects.
• Simulated Stereo: Your TV will create a simulated
stereo effect when watching a non-stereo
program.
• Surround Sound: Your TV will create a simulated
surround effect when watching a stereo program.

◊

Level Sound
Turn On or Off to automatically equalize the
volume level when there are significant sound-level
differences between program segments, e.g.,
between regular programming and commercials. To
receive the best fidelity with music programs, turn
this setting to Off. When connecting to an A/V
receiver, set level sound to OFF and turn the TV
speakers off to send full dynamics to the A/V receiver.

Analog-Only Audio Settings

You can set analog-only audio settings while viewing
either analog or digital sources, but the settings affect
broadcast or recorded analog content.
◊

Listen to is not available for devices connected to the TV
Inputs, component inputs, or 1394 devices.

Digital-Only Audio Settings

You can set digital-only audio settings while viewing
either analog or digital sources, but the settings affect
only broadcast or recorded digital content.
◊

Chapter 5. TV Menu Operations

Language
Determines what possible language you can hear.
Your choices are:
English

Portuguese

French

Spanish

German

Other

Italian

IEEE 1394 Amplifier Settings
◊

Balance
Adjusts the level of sound between the left and right
speakers. The slider range is 0–254, with 127 at the
center.

◊

Loudness
Set to On to make the audio level more uniform.

◊

Preset
Select the mode that matches the audio source. Your
choices are:

Listen to
Determines how your TV receives a broadcast audio
signal and plays the sound you hear.
Your choices are:
• Stereo: Default setting. The TV plays stereo
broadcasts in stereo and mono broadcasts in
mono. The word “Stereo” is displayed when you
tune to a channel broadcasting in stereo.
• SAP (Second Audio Program): Additional
monaural sound track that you cannot hear
during normal TV viewing. The SAP signal might

•

◊

•

Off

•

Classical Music

•

Jazz

•

Movie

•

Rock

•

Speech

Equalizer
Equalize the sound.

Video Settings
Video Settings

adjusting. Each TV input or device has a memory for
PerfectColor. While using the PerfectColor option,
press CANCEL if you want to reset the colors to the
default settings.

Press the VIDEO key repeatedly to cycle through the
Video options to the one you want to change. Use
ADJUST
to change settings.
Bright/Natural Modes
Bright and Natural modes are available for some settings
and allow you to optimize the image for a brighter
(daytime) or dimmer (nighttime) viewing environment. To
do this, your TV remembers two independent Contrast,
Brightness, and Color Temperature settings, one for each
of the two modes. Whenever you change settings for
Contrast, Brightness, or Color Temperature, first check
which of the two modes (Bright/Natural) is active.

◊

Contrast (Bright/Natural)
Provides a slider to adjust the white-to-black level.
Low contrast shows a variety of shades in darker
images, while high contrast shows darker images
more uniformly black and makes colors appear more
vibrant. In most home lighting situations, a medium
contrast looks best. High contrast is good for brightly
lit environments.
Brightness (Bright/Natural)
Provides a slider to adjust the overall brightness of
the picture.

◊

Color
Provides a slider to adjust the color intensity.

◊

Tint
Provides a slider to adjust the ratio of red to green.

◊

Sharpness
Provides a slider to adjust the detail and clarity.

◊

Color Temp (Bright/Natural)
Allows you to adjust how white images are displayed.
Your choices are:
• Low: White images will have a warm cast to them.
This adjustment is an average and can vary due
to ambient room lighting, video scene brightness,
and the TV’s age. Natural/Color Temp at the
low setting displays video at the 6500K industry
standard for NTSC pictures.
• High: White images will have a cool cast to them.
This setting may provide the most realistic picture
under bright lighting.

◊

PerfectColor™
Adjusts any or all of six colors (Magenta, Red, Yellow,
Green, Cyan and Blue) to create color balance.
When you select PerfectColor and press ENTER,
you can adjust the colors automatically or manually
(individually).

◊

Video Noise
Use to reduce minor noise (graininess) in the
broadcast received on Ant-1 and Ant-2, Inputs
1–3, Component 1–3, and HDMI 1 and 2. Use the
Standard setting with good-quality signals.
NOTE: A slider displays on screen for most settings.
When the slider is displayed, it represents numeric
values, with 63 as the maximum, 31 as the mid-point,
and 0 as the minimum.
DeepField™ Imager
When On is selected, the black levels are dynamically
enhanced in portions of the screen to provide strong
contrast with detail over mixed screen content.
When Off is selected, the entire screen adjusts the
contrast the same. When Demo is selected, a split
screen picture appears and you can see how the
picture will look when DeepField Imager is On (right
side) or when it is Off (left side).
SharpEdge™
When ON is selected, special edge sharpness
enhancements are applied to the vertical edges of
images.

PC Video Settings
◊
◊

◊

Auto Position. Press ENTER to automatically center
the position of the PC video.
HorizPosition (Horizontal Position). Manually
adjust the horizontal position of the PC. This
selection overrides the Auto Position selection.
VertPosition (Vertical Position). Manually adjust
the vertical position of the PC. This selection
overrides the Auto Position selection.
Fine Detail. Manually adjust the picture quality of
the PC. This selection overrides the Auto Position
selection.

Individual sliders for each color are displayed.
Highlighted text shows which slider you are

Chapter 5. TV Menu Operations

Chapter . . .

Additional Features
MediaCommand™ and Memory Card Playback..
Operation of PIP and POP. . . . . . . . . . . . . . . . .
TV Display Formats.. . . . . . . . . . . . . . . . . . . . .
PC Viewing. . . . . . . . . . . . . . . . . . . . . . . . . . .
PC Display Formats. . . . . . . . . . . . . . . . . . . . .

.
.
.
.
.

84
86
87
89
90

MediaCommand™ and Memory Card Playback
Warning: Some memory cards available on the market are not properly certified to follow the card type
specifications noted below and cannot be used by the card reader. If you experience problems with the
reading of your file, please transfer your files to a properly certified card.

Memory Card Slots
Inserting a memory card
1.

Insert a card into a matching card slot on the front
of the TV. Be sure to use the correct card slot.
Card 1 accepts SmartMedia™. Card 2 accepts
MultiMediaCard™ and SD Media Card. Card 3
accepts CompactFlash® and MicroDrive®. Card
4 accepts MEMORY STICK™ and Memory Stick Pro.
Cards up to 1 GB, with a file format of FAT 16 (block
size = 1024 or 2048) are supported.
Normally the label side should be up, but if the card
does not fit, try turning the card over and insert again.
When properly inserted, the light next to the slot will
light up.

2. Press DEVICE on the remote control to display the
Device Selection Menu and then select the correct
.
card slot from the list, using ADJUST
3. The Media Dialog box (figure 1) will automatically
display. Use the AUDIO button to switch from JPEG
Picture Slide show setup to MP3 or WMA7 Audio
Playlist setup, or use the VIDEO button on the remote
to switch from the MP3 or WMA Audio Playlist setup
to JPEG Picture Slide show setup.
Don’t pull the memory card out while it is playing.

For Slideshow, press PLAY.
For Thumbnails, press GUIDE.
To redisplay this menu or to
setup, press DEVICE MENU.
For Playlist, press AUDIO.

Remote Control Buttons for Controlling the Playback
For JPEG Picture Slide show:
PLAY:
begins or resumes slide show playback
PAUSE:
pauses or resumes playback while in the
automatic advance mode.
FF:
skips to the next slide.
REW:
returns to the previous slide.
FORMAT: single press rotates the slide 90˚. Multiple
presses continue to rotate the slide.
STOP:
Stop slide show, return to memory card
screen.
For MP3 or WMA Audio Playback
PLAY:
begins or resumes playlist playback.
PAUSE:
pauses or resumes playback.
FF:
skips to the first track/song.
REW:
skips to the previous track/song.
STOP:
Stop playback and returns to memory card
screen.
Using the Picture Thumbnail Menu or Audio Playlist
Menu
For JPEG Picture Thumbnail Menu:
Figure 2

Press GUIDE on the remote to display the JPEG
picture Thumbnail menu.
2. Press ADJUST
to move the highlight to
different images (CH up/down will change pages of
the Thumbnail menu). Use REW to go to the first slide
and FF to go to the last slide on the page.
3. Press FORMAT to rotate the selected image 90˚
(pressing FORMAT four times will rotate the image
completely around to the original position).
4. Press PLAY to begin playback of the Slide show from
the selected image. The Thumbnail menu will be
taken down.

Figure 1. Media Dialog Box
4. On the remote control, press:
PLAY:
to start the slide show or play audio.
GUIDE: to display the JPEG Thumbnail menu (Figure 2)
or Audio track playlist (Figure 3)
DEVICE
MENU: to display the Media Setup menu (Figure 4 ).

Figure 2. JPEG Thumbnails

Chapter 6. Additional Features

Media Command™ and Memory Card Playback, continued
For MP3 or WMA7 Playlist Menu:
Figure 3

Press GUIDE to display the Playlist menu.

2. Press ADJUST or to select different tracks (CH
up/down will change pages of the Playlist). Use REW
to go to the first track on the page and FF to go to the
last track on the page.
3. Press PLAY to begin playback. The Playlist menu
will be taken down. The song currently playing will be
highlighted.

Figure 3. Audio Playlist
COMPATIBLE PICTURE OR AUDIO FILES:
For JPEG Pictures up to 1 GB:
1.

Still images recorded on digital cameras using the
Exchangeable Image File Format, version 2.1 (EXIF
2.1) standard for digital still cameras and Design
Rules for Camera File Systems version 1.0 (DCF 1.0)

NOTES
• During WMA7 audio playback, audio from the cards is
sent to the A/V receiver as analog audio. Digital out is
not available.
• Repetitive noise may be present when playing WMA
digital audio files from memory files.
Media Setup Menu
Figure 4

Press DEVICE MENU at any time to display the Media
Setup screen, where you can adjust the Slide show
Display, Frequency, Interval or Playlist Frequency.
For JPEG Picture Slide Show Setup
• For JPEG picture slide show playback, select
Automatic or Manual advance. For manual operation,
press PLAY or ENTER on the remote control to
advance each slide.
• For automatic advance, select the frequency or
number of times to show the complete slide show,
Once, Twice or Continuously.
• For automatic advance, select the interval time each
slide is shown, for example, five seconds, or 30
seconds
For MP3 or WMA7 Audio Playlist Setup
• Select the frequency or number of times to play the
complete playlist. Once, Twice or Continuously.
To exit, press DEVICE MENU on the remote control to
redisplay the memory card screen.

Some images opened and resaved on a computer
may not play back or may not be able to display a
picture in the thumbnail list because the computer
program that opened and resaved the images
changed the file to an incompatible format.
2. Standard digital images with a maximum size of
5 megapixels for each image, or 2560 x 1920 pixels.
Pictures will be scaled to the TV display. Some
pictures may be cropped to fit.
3. Full path file names can be no longer than 50
characters and must end in a .jpg extension. Not all
50 characters will display.

Figure 4. Media Setup Menu

Images larger than 256MB can take a longer initial
time to display.
For MP3 or WMA7 Audio files:
• Files recorded with sampling rates of 32 kHz, 44.1
kHz or 48 kHz.
• Files recorded with fixed bit rates
• File names with .mp3 or .wma extensions

IMPORTANT

JPEG images cannot be edited through the TV.
Only name changes should be made on your PC
to avoid file incompatibility problems.
MP3s must have at least 32-kHz sampling rate.

Chapter 6. Additional Features

Operation of PIP and POP
You can display programs from analog channels, analog inputs, or analog devices as picture-in-picture (PIP) and picture-outside-picture (POP). The TV has a second analog tuner for non-scrambled analog channels received on ANT‑1
and displays them as the PIP/POP sub-pictures. Digital channels and devices can be shown as the main picture but
cannot be the sub-picture. PC screens can be viewed as the main picture with PIP.
Press PIP/POP to activate the PIP/POP option. With each
press of the PIP/POP button on the TV remote control,
(within seconds of each press), the PIP/POP cycles
through the following display options:

MAIN
PICTURE

Side-by-Side

Side-by-side
pictures
(Not available
when PC is
source)

3 POP
POP 1
MAIN
PICTURE

POP 2

(Not available
when PC is
source)

POP 3

Ant-1 2 XXXX
Standard
Stereo SAP
TV-PG DLSV
SQV1

PIP Ant-1 17

PIP
(PC as main
picture only)

PIP

Ant-1 2 XXXX
Standard
Stereo SAP
TV-PG DLSV
SQV1

PIP off

Exchanging Program Images

Press EXCH to exchange the main picture and the PIP/
POP picture. Pictures from digital channels can only be
shown as the main picture. PC images can only be the
main picture. If you press EXCH while viewing images
from a PC, the TV exchanges audio with the PIP but
leaves the main image in place.

Moving a PIP Image

If no menus are on screen, press ADJUST , , , or
to move the PIP display anywhere on the main screen.
When the main picture is from a PC, the PIP can be
moved through four designated positions.

Automatic POP Switching

When automatic POP switching is active, the TV cycles
through memorized analog channels on Ant-1 or Ant-2 or
strobe pictures from other A/V components in the POP
display. Press PAUSE to pause or restart automatic POP
switching.

Selecting POP “Live” Image

Press ADJUST
to select a different POP “live”
image (automatic POP switching must be paused.)

Freezing the PIP and Side-by-Side
Pictures

Press PAUSE to freeze the PIP and side-by-side images.
Press PAUSE again to return to a “live” image.

IMPORTANT
To turn PIP/POP off, wait at least 10 seconds and then
press PIP/POP. The next time you activate PIP/POP, the
last-used PIP/POP option will be displayed.

•

The side-by-side option cannot show the
same channel or device on both sides.

•

If ANT-1 or ANT-2 is the main picture,
ANT‑2 is not available as a PIP, POP, or
side-by-side image.

•

PIP/POP is not compatible with signals
from memory cards.

•

You can view only one HDMI input at a
time with the PIP/POP or side-by-side
feature.

Changing PIP/POP Device

When PIP is displayed, press PIP DEVICE to change the
PIP picture source device. A menu similar to the Device
Selection menu will be displayed.

Changing PIP/Side-by-Side Channels

Press PIP CH to scroll up and down through memorized
channels on ANT-1 and ANT-2.

Chapter 6. Additional Features

TV Display Formats
This is a widescreen TV, also known as a 16:9 TV. This shape reflects the new types of images available from HDTV and
many DVDs. There are still many older style narrow-screen images (called 4:3 aspect ratio) you will encounter. While
there will never be a perfect solution for displaying a narrow image on a wide screen, Mitsubishi offers several display
formats from which to choose.
Press FORMAT on the TV remote control to cycle through
the available display formats. The last-used format for
each device is used when you return to that device.
Note: Not all formats are available for PIP/
POP. Side-by-Side is only available in Standard
and Expand formats. Three POP is available
in Standard format only. PC formats vary
depending on the PC signal.

DVD Definitions:

Anamorphic (or Enhanced for Wide-Screen TV’s):
These DVDs are recorded in a special way to properly
show wide-screen images on 16:9 TV sets in the
Standard format mode. This is the recommended choice.
Non-Anamorphic (or 4:3, 1:33:1, Letter box or Full
Screen):
These DVDs are recorded for use with traditional shaped
TVs. They may be full screen (4:3 or 1:33:1) which crops
movies to fit the narrow TV, or Letter boxed, which adds
black top and bottom bars.
This information may or may not be listed on the DVD
case. Some DVDs support both types of recordings.

Signal Definitions

480i Signals: Traditional analog interlaced signals from
or through ANT-1 and 2, INPUT 1 and 2, COMPONENT 1–3,
and HDMI 1 and 2.

480p Signals: Progressive-scan analog DVD signals on
COMPONENT inputs and HDMI 1 and 2.

720p & 1080i Signals: High-definition analog signals
received through COMPONENT 1–3 and HDMI 1 and 2.
These signals are always 16:9 (widescreen).

SD 4:3: Standard-definition narrow-screen format signals
from digital channels and IEEE 1394 devices.

SD 16:9: Standard-definition widescreen format signals
from digital channels and IEEE 1394 devices.

HD: High-definition wide-screen format signals from digital
channels and IEEE-1394 devices. These signals are always
16:9 (widescreen).

Format Definitions

Standard: This is the full-screen format. HDTV signals
use this format. This format is useful for displaying
Anamorphic DVDs that have 1.78:1 or 1.85:1 aspect
ratios. Anamorphic DVDs that have a 2.35:1 aspect ratio
are displayed with black bars at the top and bottom, but
show the entire image correctly. Narrow (4:3) images
are stretched evenly from side to side. Available for all
signals.
Expand: This enlarges the picture to fill the screen,
cropping off some of the image at the top and bottom.
This is useful for reducing the letter box top and bottom
bars of non-anamorphic DVD images. Available for
analog 480i, 480p and digital SD 4:3 signals only.
Zoom: This enlarges the picture, cropping off some
of the image at each side and top and bottom. This is
useful for removing or reducing the black top and bottom
bars on anamorphic DVDs with a 2.35:1 aspect ratio.
Available for analog 480i and 480p and SD 4:3 signals
only.
Stretch: This format stretches a narrow (4:3) image
across the screen; there is less stretch in the center than
at the sides, however. This allows the entire narrow
image to be displayed across the screen with less
distortion than is seen in the Standard format. Available
for analog 480i and 480p and SD 4:3 signals only.
Stretch Plus: Similar to stretch mode, but to minimize
distortions on the side, the picture is expanded to
crop off portions of the top and bottom. When no PIP
is displayed, you can press ADJUST up or down to
vertically adjust the position of the picture. Available for
analog 480i and 480p and SD 4:3 signals only.
Narrow: This format displays narrow (4:3) images in their
original shape, and adds stationary black side bars to fill
the screen. Available for 480i, 480p and digital SD 4:3
signals only.
Wide Expand: Enlarges the picture, cropping some of
the image on both sides. This Expand format is useful
to remove or reduce black side bars added to narrow
images that are converted to 16:9 signals for digital
broadcast. Available for analog 1080i, 720p, digital SD
16:9 and digital HD signals.

Chapter 6. Additional Features

TV Display Formats
03*(*/"-4*(/"-
"OBNPSQIJD%7%

03*(*/"-4*(/"/POBOBNPSQIJDPS4%

57%JTQMBZ

4UBOEBSE

4UBOEBSE
OPUSFDPNNFOEFE EJTUPSUFE

SFDPNNFOEFE

OPUBWBJMBCMFGPS
)% 4%PS
BOBMPHQ J

&YQBOE

OPUBWBJMBCMFGPS
)% 4%PS
BOBMPHQ J

SFDPNNFOEFEGPSMFUUFSCPYFE
OPUSFDPNNFOEFE EJTUPSUFE

OPUBWBJMBCMFGPS
)% 4%PS
BOBMPHQ J

;PPN

OPUBWBJMBCMFGPS
)% 4%PS
BOBMPHQ J

OPUSFDPNNFOEFE EJTUPSUFE
SFDPNNFOEFEGPSBOBNPSQIJD

OPUBWBJMBCMFGPS
)% 4%PS
BOBMPHQ J

4USFUDI

OPUBWBJMBCMFGPS
)% 4%PS
BOBMPHQ J

SFDPNNFOEFEGPSTUBOEBSECSPBEDBTU
OPUSFDPNNFOEFE EJTUPSUFE

OPUBWBJMBCMFGPS
)% 4%PS
BOBMPHQ J

4USFUDI1MVT

SFDPNNFOEFEGPSTUBOEBSECSPBEDBTU

/BSSPX

OPUBWBJMBCMFGPS
)% 4%PS
BOBMPHQ J
OPUSFDPNNFOEFE EJTUPSUFE

/BSSPX

OPUBWBJMBCMFGPS
)% 4%PS
BOBMPHQ J
OPUSFDPNNFOEFE EJTUPSUFE

)
%
%
*
(
*
5
"
-

4UBOEBSE
0SJHJOBM)%PS4%
QPSJ

BWBJMBCMFPOMZGPS
EJHJUBM4% )%
BOBMPHJPSQ

XJUITJEFCBSTJOCSPBEDBTU
SFDPNNFOEFEUPSFNPWFTJEFCBST

8JEF&YQBOE

Chapter 6. Additional Features

PC Viewing

Figure 1

To display your PC screen on the TV, first connect
the PC to the HDMI 2 input on the TV’s back panel
(see Chapter 2). You must then activate the PC
option in NetCommand. You can do this during initial
NetCommand setup by selecting the PC option in the
Device Setup screen. To do this at any time afterwards,
use the NetCommand Add function. You will then be able
to select the PC through the Device Selection Menu. For
the correct screen resolution (pixels), use the PC’s Control
Panel settings as described below.
Your Mitsubishi TV can display resolutions from standard
VGA (640 x 480) through XGA (1024 x 768) 60-Hz refresh
rates only. See Appendix A in this book for more on
screen resolutions. The instructions below are for most
PCs.
1.

In the PC’s Start menu, select Settings.

2. Select Control Panel.

5. Depending on your PC, adjust the resolution with
either:
• the Screen area slider.
• the Screen Resolution slider
You may need to restart the PC for this change to take
effect.

Hint: Whenever the TV is powered on, the lamp is
in use, even if the TV screen appears dark. As a
reminder that the TV is powered on and that time
is being added to the lamp’s elapsed hours, set the
computer’s screen saver to a pattern that will display
after several minutes of inactivity.

3. Select Display.
4. Choose the Settings tab.

Figure 1. PC resolution XGA selection

Chapter 6. Additional Features

PC Display Formats
Signal Format

Original Pixel Counts

16 X 9 Standard

4 X 3 Standard

1696 X 960

1280 X 960

1696 X 960

1280 X 960

1702 X 960

1280 X 960

1702 X 960

1280 X 960

Standard

Zoom

1024 X 768

1280 X 960

1280 X 720

1706 X 960

VGA
640 X 480

WVGA
848 X 480

SVGA
800 X 600

WSVGA
1064 X 600

Signal Format

Original Pixel Counts
XGA
1024 X 768

PC720p
1280 X 720

Chapter 6. Additional Features

Chapter . . .

Troubleshooting

General TV Operation
Symptom

Suggested Solution

The TV remote control does not work.

•
•
•
•

Check that the batteries are installed correctly.
Check that the selected switch is set to “TV.”
Be no more than 20 feet from the TV when using the remote control.
Program the remote control to operate the TV (Appendix D).

The TV takes several seconds to respond.

•
•
•
•

It is normal for digital channels to take longer to tune in.
Press ENTER after a channel number to avoid delays.
Use a 4-digit number for an over-the-air digital channel.
Use a 6-digit number for digital cable channels (your cable service must be able
to recognize 6-digit channel numbers).

Cable provider needs information to start
CableCARD™ service.

On the remote control, press TV MENU and then enter the numbers 999
to display the Host ID and CableCARD™ ID information.

You cannot access a channel.

• Use number keys instead of CHANNEL up/down.
• Be sure the channel you want to view is in memory. See page 67.
• Check that the TV is turned to the correct device or antenna for that channel by
pressing the DEVICE button.
• Make sure the V-Chip lock is off.
• If you cannot tune to a virtual digital channel even though the TV has already
memorized digital channels, tune to the channel number actually being used by
the broadcaster. The virtual channel will then be automatically added to memory.

On-screen displays appear each time you change
a function.

This is part of normal TV operation.

You cannot program the TV to turn on
automatically (timer function)

• The TV may be locked.
• The clock may not be set.
• A time-delayed recording may have started.

You have forgotten your V-Chip pass code.

See Appendix C, Bypassing the V-Chip Lock.

V-Chip is not working.

• Make sure that V-Chip is On.
• If V-Chip Hours are currently set to disable the V-Chip lock, the V-Chip will not
block programming.

The TV will not turn on after being plugged in.

If green light on front panel is blinking, wait for at least one minute for
the light to turn off, then press Power again.

10.

TV functions do not respond to the remote control Use the System Reset button .
or to front panel control and TV will not power off.

11.

TV turned itself off and the light on the front panel
started to blink.

• Momentary power fluctuation caused the TV to turn off to prevent damage. Wait
for the green light to stop flashing and turn On again.
• If the TV does not stay turned On, use the System Reset button. If this happens
frequently, obtain an AC line power conditioner/surge protector.
• An unusual digital signal may have been received, triggering a protection
circuit. Wait for the light to stop flashing and turn TV on.

12.

Name options not available for some channels.

Only memorized analog channels can be named.

13.

When a device is selected from the Device
Selection menu, the screen is blue (no signal
source).

• Make sure the selected device is turned on.
• From the Edit NetCommand® menu select Review setting. Verify that the devices
are physically connected to the TV inputs as listed. If they are not, either change
the physical connections on the back panel, or select the Change setting on
the Edit NetCommand menu to change the TV NetCommand’s settings for the
connection.
• Begin play of the VCR.

Chapter 7. Troubleshooting

General TV Operation
Symptom

Suggested Solution

A device does not respond to button presses
from the remote.

• Remote has not been set up for NetCommand® use.
• The incorrect manufacturer was selected during setup. Select the Change setting
from the Setup menu and then the device to display the manufacturer selection.
Change if necessary.
• The device is not supported and keys have not been learned.
• The requested function is not supported by NetCommand. Verify that the
function is supported or keys are learned.
• The IR emitter is incorrectly placed. Make sure the IR emitter is facing the IR
sensor in the device.
• The IR emitter is not plugged into the IR emitter Output NetCommand.
• The IR emitter is facing the TV screen, causing double signals. Be sure that the IR
emitter cannot send to the TV.

15.

The TV Speaker icon or A/V Receiver icon is
grayed out and not selectable.

Select the Change setting from the Edit NetCommand menu, and then
select the device (for example VCR). Once the Connection screen is
displayed, check if the audio check box is selected for the TV input and/
or AVR input.

16.

Devices are grayed out in the Device Selection
menu or the PIP Selection menu.

• A recording is in progress. Cancel the recording to select the device.
• Digital channels, digital devices, memory cards, and PCs cannot display in the
PIP.

17.

Cannot see the A/V Receiver menu.

The A/V Receiver is not connected to any input of the TV. To check the
A/V Receiver menu, temporarily plug into an unused input of the TV.
Then select Review from the Setup Menu, turn the input On to view the
A/V Receiver menu.

18.

The REC button is not working, or, on the
Transport menu, the record key is grayed out and
not available.

• The device, such as a DVD player, does not support recording.
• Recordings cannot be initiated from the Transport menu when using an IEEE
1394 device. Press REC instead. The Record menu displays allowing setup of a
recording.

19.

When ChannelView™ list is displayed, information
appears incomplete

Available information is sent from the broadcaster or cable provider. No
other data is available.

20.

Program to be recorded was correctly selected
from ChannelView, however, incorrect program
was recorded.

The broadcaster supplied program information that was incorrect and/or
was changed after a recording was added to the Record List.

21.

Incomplete ChannelView program recorded.

Recording device may lack sufficient blank space to make a full
recording.

22.

ChannelView program recording failed.

• Connection and compatibility issues with IEEE 1394 (FireWire®) digital devices.
This may include too many Firewire devices in use at one time, or the recording
device not understanding the record command.
• Television lost power long enough to lose current clock time.
• Analog VCR power was left off.

23.

TV is not responding after pulling out a memory
card during playback.

Press STOP or wait until playback is complete before removing memory
card.

24.

TV can’t play or stop a memory card.

• NetCommand was not set up. Without NetCommand enabled, you can only use
ENTER to play and CANCEL on the TV remote to control the memory cards. See
Appendix D for programming the remote control.
• Turn the TV off and then back on.

25.

Can’t see a thumbnail picture in the JPEG menu,
or can’t see a track/song name in the Playlist
menu.

File does not meet file standards for playback.

Chapter 7. Troubleshooting

General TV Operation
Symptom

Suggested Solution

26.

The message “Lamp will soon exceed...” keeps
displaying after the lamp has been replaced.

Reset the lamp reminder in the setup menu.

27.

NetCommand unable to learn specific device
keys.

• Device does not use IR format for remote control signal. ITT and RF formats
cannot be learned.
• Room lighting may affect the signal. Have the remotes very close (6 inches or
less) to the TV during Learning.
• If using a Mitsubishi remote control, make sure slide switch is not set to TV
position.
• Some, but not all, device key functions can be learned by NetCommand. For
example, POWER and PLAY may be learned, but other functions may not
• The signal from the remote control ay not be strong enough. Insert fresh batteries
and try Learning again.

Picture
1.

Symptom

Suggested Solution

PIP does not display a picture.

• Make sure the V-Chip lock is off.
• Not all inputs can be displayed as a PIP.

Digital channels do not appear in PIP.

Normal PIP operation.

There is a large black or gray rectangle on the
screen.

The TV’s analog closed captioning has been set to “text”
mode in the Captions menu. Turn off because there is no text
information being broadcast.

You cannot see a picture when playing a VHS
tape.

• Display the Device Selection menu and select the correct VCR.
• Check your VCR’s owner’s guide for further troubleshooting.

When viewing a stopped VCR, white lines are
rolling on the screen.

• Turn off video mute for the VCR.
• Begin playing the tape.
• Change the VCR input to the antenna input.

Screen is black when trying to view digital
channels or IEEE 1394 device.

The PerfectColor™ color balance has been incorrectly set.
Press VIDEO repeatedly until you see the PerfectColor option
and press ENTER.

A program recorded on your widescreen TV is
distorted when played on a 4:3 TV.

TV was set to Anamorphic when program was recorded.
Record programs in Cropped mode if playing back on a 4:3 TV.
Open the Record menu and select Cropped before making such
a recording.

Cannot see a picture from a DV Camcorder.

DV formatting was not detected during automatic discovery,
so you must specify it manually. Open the Edit NetCommand
screen, select Change, then select the camcorder, Add, and in
the Name for 1394 Device screen, check mark the DV box.

DVCR analog/digital problems.

If the tape is currently playing but no picture displays, there may
be a mismatch of the media with the display. Press DEVICE to
display the Device Selection menu. Press ENTER for the DVCR
device. If digital is selected, try analog, or if analog is selected,
try digital.

Chapter 7. Troubleshooting

Sound
Symptom

Suggested Solution

There is no sound even when the volume is
turned up.

•
•
•
•

Check audio source in Device Menu.
Check to see if the MUTE button is on.
The TV’s “Listen to:” setting may be set to SAP.
Check that the “TV Speakers” setting is On in the Audio/Video menu.

The sound does not match the screen
picture.

•
•
•
•

NetCommand® is set up incorrectly.
The TV’s “Listen to:” setting may be set to SAP.
If using stereo or A/V receiver speakers, check their input selection.
If using stereo or A/V receiver, check that AUDIO OUTPUT on TV’s back panel
is connected to the A/V receiver.

The A/V Receiver is the selected audio
source but there is no sound.

• Check to see if the A/V Receiver power is turned on. After the power is
turned on, redisplay the Device Selection menu and press ENTER to allow
NetCommand to correctly select the A/V Receiver input.
• Verify the connections and NetCommand setup for the A/V receiver and the
desired source device, if any.
From the NetCommand menu, select Review. Check the Review screen to
see if the A/V Receiver inputs and device listed correspond to the physical
connections on the A/V Receiver. If they do not match, either change the
physical connections or change the NetCommand setup. To change the
NetCommand setup, make the audio source the TV speakers and select a
source other than the one you want to change. Next select the Change option
on the Edit NetCommand menu to change the A/V receiver input for the device
on the Connection screen.

Indicators
Symptom

Suggested Solution

Lamp indicator light is a constant red.

Turn the TV off for at least 2 minutes. Turn back on. If light is
still red, the lamp has failed. Replace it. See Appendix H for
lamp replacement information.

Lamp indicator light is a constant yellow.

Lamp may fail soon. Purchase a new lamp. See Appendix H for
lamp replacement information.

Lamp indicator light is a flashing yellow.

Lamp cover door is open or lamp cartridge is not secure. See
Appendix H for lamp replacement information.

Status indicator light is a constant yellow.

Room temperature has exceeded proper levels. Cool the room.

Status indicator light is a constant/flashing red.

Service is required. Contact your dealer or a Mitsubishi
Authorized Service Center to arrange for a service evaluation.
Listings of Mitsubishi Authorized Service locations can be
obtained from our web site, www.mitsubishi-tv.com or by
calling 1-800-332-2119.

Chapter 7. Troubleshooting

IEEE 1394 Devices
Symptom

Suggested Solution

Excessive digital artifacts when viewing an IEEE
1394 device.

• The IEEE 1394 cable is too long; 15 feet between devices is the maximum.
• There may be a slow device in the middle of the IEEE 1394 network. Move the
slow devices to the end so that connections for faster devices do not pass
through them.

D-VHS recordings for digital cable have
drop-outs (loss of picture or sound), or no
playback.

Digital cable signals on IEEE 1394 can exceed the data rate standards
supported by DVCR.

There is no audio and video from the IEEE 1394
device.

•
•
•
•
•
•
•
•
•

The device is not turned on. Turn the device power on.
No media (tape or disc) is inserted into the device.
The media is blank (has no recording).
The play command failed - Try pressing play again on the device’s remote control
or front panel.
The device is already in use (for example, the device is currently recording).
The source is copy-protected or violates copy protection.
The device’s digital video signal is not supported by the TV, as may be the case
with an IEEE 1394 signal from a computer. Use analog connections instead, if
available.
The device is not an audio/video device.
Too many other devices are already communicating over IEEE 1394. Remove or
stop some devices and try again.

The IEEE 1394 Device is not listed in the Device
Selection menu.

• The device is unchecked in the Review screen. Select the NetCommand menu.
Through Review, verify the device is checked.
• The IEEE 1394 plug is disconnected or loose.
• The IEEE 1394 Device has not been powered On. Turn on.
• The device has not been discovered.
• The device is not an Audio/Video device

The IEEE 1394 device cannot be selected (is
grayed out).

The device may be busy, either recording or a peer-to-peer connection
has been established. Cancel the recording or peer-to-peer connection.

DEVICE MENU button does not display a menu.

• The IEEE 1394 device does not provide a menu.
• The TV cannot support IEEE 1394 menus.

All IEEE 1394 devices disappear.

• The connected devices must not be in a loop that returns to the TV. Make sure a
device is connected at the end.
• Disconnect all the cables and devices from the TV. Replace them one by one to
locate the problem device or cable
• Use System Reset (front control panel).

Cannot rediscover a deleted IEEE 1394 device.

• The device has been disconnected. Plug it in.
• The device is unchecked in the Review screen. Select NetCommand from the
Main menu, then select Review. Check the device.
• Remove IEEE 1394 plug. Go to the Edit NetCommand menu. Delete the IEEE
1394 device. Plug the device in again so it can be discovered again.

An IEEE 1394 device has been plugged in but
does not appear in the Device Selection menu
(not discovered).

•
•
•
•
•
•

Chapter 7. Troubleshooting

The IEEE 1394 connection to the TV or another device is not secure or is loose.
The IEEE 1394 device is not powered on.
A device in the IEEE 1394 chain is not powered on. Turn on all the devices.
The device discovery can take as long as a minute to initiate.
IEEE 1394 cable is too long (maximum of 15 feet between devices).
The IEEE 1394 device uses an incompatible protocol and will not be discovered

IEEE 1394 Devices
Symptom

Suggested Solution

10.

Cannot record to or from the IEEE 1394 device,
including dubbed recordings.

• To initiate a recording to IEEE 1394 device, press the REC key. The Record menu
displays allowing setup of the recording.
• The source device for the recording is not powered on.
• When dubbing, the destination device for the recording is not powered on.
• The wrong medium (analog tape for digital recording, or digital tape for the analog
recording) is in the device.
• The program is copy protected.
• The program has already been recorded once and the copy protection only allows
one recording.
• Unapproved source device for copy protected material.
• The recording device can not decode the copyright signal included in the signal
source (try another device if available).
• The playing device (for dubbing) does not support copyrighted material.
• Source for recording is copyrighted
• Too many IEEE 1394 devices in network. Insufficient bandwidth available.
Disconnect unused devices.
• Source Device has higher speed (S 400) than record device. If possible, reverse
devices, play in the slower device and record in the faster device.

11.

Cannot control the IEEE 1394 device from the
Transport Menu.

• Device may not support the command.
• Selected function is gray (such as Record for a DVD, which does not support the
Record function.

TV Guide On Screen

(see the separate TV Guide On Screen® Interactive Program Guide User’s Manual for detailed information)
Symptom

Suggested Solution

TV Guide On Screen® system shows no program • Program listings are downloaded while the TV is off and the cable
listings.
box is left on. It may take up to 24 hours to begin to receive TV
program listings. It may take up to one week to receive all eight
days of TV program listings.
• Invalid ZIP code was entered at the initial TV Guide On Screen
system setup. Select NetCommand from the main TV menu, then
Guide and enter the correct ZIP code.
• Check the connections between the TV and the TV Guide On
Screen input (cable, antenna or cable box and IR cable). At least
one antenna connection must be associated with the TV Guide On
Screen system to receive program listings.

TV Guide On Screen system program listings
don’t match actual programs

• Incorrect ZIP code was entered at initial TV Guide system setup.
Select NetCommand menu, then Guide to enter the correct ZIP
code.
• For cable programs, there may be more than one cable company
in your ZIP code. Refer to the TV Guide On Screen system manual
for instructions on the Setup Service.

TV Guide On Screen system does not change
channels on the cable box.

• Cable box is not set up in NetCommand. The TV Guide On Screen
system uses NetCommand to control the cable box and VCR. To
correct, select NetCommand from the main TV menu, then select
Change or Add on the NetCommand menu and select Cable Box.
• NetCommand IR emitter is not in place or properly positioned in
front of the cable box remote sensor. See page 32.

Chapter 7. Troubleshooting

Appendices
Appendix A:
Appendix B:
Appendix C:
Appendix D:
Appendix E:
Appendix F:
Appendix G:
Appendix H:
Appendix I:

Specifications.. . . . . . . . . . . . . . . . . . . .
On-Screen Information Displays. . . . . . . .
Bypassing the V-Chip Lock. . . . . . . . . . .
Remote Control Programming Codes. . . .
Device Control with NetCommand®. . . . .
NetCommand® Specialized Device Keys. .
Cleaning and Service.. . . . . . . . . . . . . . .
Lamp Cartridge Replacement.. . . . . . . . .
Recording and Viewing Combinations. . . .

.
.
.
.
.
.
.
.
.

100
102
103
105
108
110
111
112
114

Appendix A: Specifications
From time to time, Mitsubishi may offer software updates to expand the features or operation of this TV. When these
updates are available they will be announced on our web site, Mitsubishi-tv.com. If you return your owner’s registration
card, with your model and serial number, you may receive written notification of available software updates.

TV Specifications
Projection System

DLP, 0.843” chip, 1920 x 1080 pixels with Smooth Picture™

Lamp

WD-52628, WD-62628: 120-watt VIP type
WD-73727: 150-watt VIP type

Channel Frequency Reception

Over-the-Air: VHF 2–13, UHF 14–69
Analog Cable: 1–125
Digital Cable: 1–135

Channel Type

Over the Air: Analog NTSC, Digital ATSC with sub-channels (all 18 video
formats)
Cable:
Analog NTSC (non-scrambled)
Digital QAM 64 and 256 with sub-channels
(non-scrambled)
CableCARD™: Authorized scrambled and non-scrambled digital
channels

Note for Digital Channels: The channel numbers displayed on screen are determined by the broadcaster or cable
company and can vary from the standard frequency number. If there is no channel number information included from
the broadcaster or cable company, then the TV will create a channel number based on the frequency number as the
main channel number and the program number as the sub-channel number. When using an authorized CableCARD,
the channel numbers are determined by the cable company.

Inputs
Antenna/Cable input Qty. 2

F connector, 75-ohm

HDMI (digital video/audio), Qty. 2
Signal Type

HDMI standard connector
HDMI EIA-861B standard for digital audio and video.
Video: 480i, 480p, 720p, 1080i
Audio: PCM stereo
HDMI 1: Not intended for use with personal computers.
HDMI 2: Accepts PC input.
VGA (640 x 480), 60Hz
W-VGA (848 x 480), 60 Hz
SVGA (800 x 600), 60Hz
W-SVGA (1064 x 600), 60Hz
XGA (1024 x 768), 60 Hz
1280 x 720, 60 Hz (EIA standards)

Video/S-Video, Qty. 3 each
(1 front, 2 rear)
Signal Type

Video:
RCA Pin Plug, 1.0 V p-p, 75 ohm
S-Video: Four-Pin DIN Plug
Y: 1.0 Vp-p 75-ohm
C: 0.286 Vp-p (burst signal), 75-ohm
NTSC 480i only

Component Video (Y/Pr/Pb), Qty. 3 sets

RCA Pin Plug (EIA-770.3 Standard Levels and Timing)
Y:
1.0 Vp-p (includes sync), 75-ohm
Pr:
700 mV p-p, 75-ohm
Pb:
700 mV p-p, 75-ohm

Signal Type

EIA-770.1 & EIA 770.2 480i, 480p, EIA 770.3 720p and 1080i (video standards)

100

Appendices

Appendix A: Specifications, continued
Audio Inputs: Qty. 7 pairs

RCA Pin Plug 500 mV (full scale), 43-k ohm

Outputs
Video, Qty. 1
Signal Type
Audio:, Qty. 2 pairs

Video: RCA Pin Plug 1.0 Vp-p, 75-ohm
NTSC 480i only
RCA Pin Plug, 500 mV rms + 200 mV (full scale) for analog sources, 1.5
Vrms + 0.5 Vrms (full scale) for digital sources.

Digital Interfaces:
Digital Audio Output, Qty. 1

RCA Pin Plug, Signal Type, Dolby Digital, PCM

IEEE 1394, Qty. 3
(1 front, 2 rear)

IEEE 1394 Four Pin type Terminal, S400

Audio/Speakers

Qty. 2 woofers 5.5" x 2.2"; Qty. 2 Tweeters 1.5" round

Dimensions:

WD-52628

34" H x 49.6 " W x 18.6 " D, 121 lbs.

WD-62628

40.5" H x 58.3" W x 19.9" D, 133 lbs.

WD-73727

44.8" H x 69.9" W x 21.5 " D, 188 lbs.

WD-52628

295 watts

WD-62628

295 watts

WD-73727

335 watts

Power Consumption

NetCommand® IEEE 1394 System Compatibility:
This television is designed to conform to IEEE 1394 AV/C Software standards in effect at the time of
development. This exciting new networking and control technology is designed to provide high-performance
digital connections and product control, making the product easier to use.
Mitsubishi D-VHS VCRs are fully compatible with this TV in audio, video, and control.
As other manufacturers distribute products that use the IEEE 1394 AV/C standards, they will be responsible
for developing products that meet the standards of the technology, as well as compatibility testing with other
products. Mitsubishi cannot be responsible for their efforts, and therefore cannot promise compatibility
with these other products. Any compatibility problems with other manufacturers products should be
brought to the attention of those manufacturers.
The HDMI input is compliant with EIA-861B standards for standard, extended and high definition video,
digital audio and HDCP copy protection. HDMI input 1, however, is not intended for use with personal
computers or devices outputting video signals with computer resolutions.

Appendices

101

Appendix B: On-Screen Information Displays
When you turn on the TV, change devices, change channels, or when you press the INFO button
on the remote control, the TV will display the current status. Below are the most common displays.
Please note that seldom or never do all of the different status indicators appear at the same time.

Analog Program

1. Antenna or Device being viewed
2. Analog channel being received: If antenna
being viewed
3. Channel name (if manually programmed)
4. Signal Type being received
Possible:
Ant-1, Ant-2 or Input 1–3 – 480i
Component 1, 2 – 480i, 480p, 720p or 1080i
5. Screen format being used
Possible:
Analog 480i /480p signals – Standard,
Expand, Zoom, Stretch, Stretch Plus, Narrow
720p/1080i signals - Standard, Wide Expand
6. Stereo and/or SAP being broadcast
7. V-Chip Ratings
8. Channel in SuperQuickView bank 2
9. Day and Time
10. Sleep Timer remaining time
11. PIP source and channel
12. Program name (if provided by TV Guide On
Screen®)
13. Audio Mute on

1
4
6

Status of D-VHS VCR or IEEE 1394 device
Counter of D-VHS VCR
Media type in D-VHS VCR
Special message line
(shows only when a special message is
needed; may be seen with Analog signals)

3
5

Appendices

ANT-1 3

5
7

MUTE

Ant-1 42-1 XXXXXXX XXXXXXXXXXXXXX
HD Standard
4
English
TV-PG DLSV
SQV2
Monday 11:00 AM
Sleep Timer: 30

1
3

102

XXXXXXXXX

Monday 11:00
AM
Sleep Timer: 30

Digital IEEE 1394 Device
1.
2.
3.
4.

Ant-1 3 XXXX
480i Standard
Stereo SAP
TV-PG DLSV
SQV2

Digital Program

1. Digital Major and Sub channel number
2. Digital Channel Name (only if broadcast)
3. Signal Type being broadcast/received
Possible: SD 4:3, SD 16:9 or HD
4. Screen format being used
Possible:
SD 4:3 - Standard, Expand, Zoom, Stretch,
Stretch Plus, Narrow
SD 16:9 or HD - Standard, Wide Expand
5. Language(s) being broadcast
6. Program Name (if broadcast)

DVCR
HD Standard
English
TV-PG DLSV
Play 01:20:15
DVHS
Monday 11:00 AM
Sleep Timer: 30
Special Message Line

Appendix C:

Bypassing the V-Chip Lock

Lock Bypass Instructions Have Been Filed for
Future Reference

Bypassing the V-Chip Lock

After you set the lock, you need your pass code to view
a V-Chip locked program, view the locked TV, cancel the
lock, or enter the V-Chip Lock menus.
If you forget your pass code, you can view the locked
TV without entering your pass code. When you are
prompted for your pass code, press the number 9 and QV
buttons on the TV remote control at the same time. This
process temporarily unlocks the TV
When entering the V-Chip Lock menu, this process
deletes your old pass code and prompts you to enter a
new pass code. Press HOME to exit the menu.

Deactivating the Front Button Lock

Press and hold the MENU button on the TV front panel for
over eight seconds.

IMPORTANT
Cut along the dotted line and file
bypass instructions in a safe place for
future reference.

IMPORTANT
When changing or deleting your pass
code, you must use the remote control
included with this TV. You cannot
use a Mitsubishi remote control from
another component or a “universal”
remote.

Appendices

103

This page intentionally blank

104

Appendices

Appendix D: Remote Control Programming Codes
IMPORTANT
The remote control may return to its
initial setting when the batteries are
changed. You may need to reprogram.

Programming the Remote to Control
NetCommand A/V Products
1.

Move the slide switch at the top of the remote to the
TV position.

2. Press and hold POWER on the remote control.
3. Enter the three digit code of 935, and then release
POWER.
4.

When the remote control is in the TV position, it is now
programmed to send NetCommand signals to the
TV so the TV can control the IEEE 1394 devices and
NetCommand-supported or learned IR devices.
This is the default setting for the remote control.

Programming the Remote to Control
Other Brands of Audio and Video
Products
1.

Move the slide switch at the top of the remote to the
product you want to control.

2. Press and hold POWER on the remote control.
3. Enter the first three digit code listed for your
equipment, and then release the POWER button on
the remote control.
4.

Point the remote control at the equipment and press
the POWER button. If the equipment responds, the
remote control is properly programmed to operate
the equipment. If the equipment does not respond,
repeat steps 2–4 with the next three-digit code listed
in step 3 for your equipment.

A/V Receivers
A/V Receiver Brand
MITSUBISHI
AIWA
BOSE
B&K
DENON
FISHER
GARRARD
HARMAN KARDON
JENSEN
JVC
KENWOOD
KLH
KOSS
MAGNAVOX
MARANTZ
MCINTOSH
NAKAMICHI
ONKYO
OPTIMUS
PANASONIC
PARASOUND
PHILIPS
PIONEER
POLK AUDIO
QUASAR
RCA
ROTEL
SANSUI
SHARP
SHERWOOD
SONY
TEAC
TECHNICS
VICTOR
YAMAHA

Code
010, 011, 012, 013, 014
225, 226, 241
351
352
234, 235, 236, 245, 246, 359, 361
204
213
215, 223, 242, 362
223, 229
232, 233
200, 208
363
357
227, 228
224, 350, 360
216
206, 217
209, 214, 240, 247
203, 227, 231, 230
219, 218, 221
356
223, 248
205, 207
353
219, 218, 221
203, 205, 227, 231, 230
366
203, 211, 239
234, 237
354, 355
222, 249, 364, 365
212, 213, 211, 210
221, 218, 219
232, 233
201, 202, 243, 244

Cable Boxes
Cable Brand
ABC
ARCHER
CABLEVIEW
CITIZEN
COLOR VOICE
COMTRONICS
CURTIS
DIAMOND
EAGLE
GCBRAND
GE
GEMINI

Code
124
125
105,
122, 105
128, 129, 130, 106, 107
128, 129, 130, 106, 107
112, 113
124, 125
129
105
112, 113
122
119, 123, 124, 125, 126, 127, 120,
GENERAL INSTRUMENT/
JERROLD/MOTOROLA
121, 122
HAMLIN
112
HITACHI
103, 124
MACOM
103, 104, 105, 108
MAGNAVOX
128, 129, 130, 106, 107, 133, 138
MOTOROLA
123, 146
MEMOREX
130
MOVIETIME
105,
PANASONIC
114
PARAGON
117
128, 129, 130, 106, 107, 131, 133,
PHILIPS
138
PIONEER
101, 106, 116
PULSAR
105
RCA
115
REGAL
112
REMBRANDT
105, 138
SAMSUNG
105
SONY
147, 177
ZENITH/DRAKE SATELLITE 100

Appendices

105

Appendix D: Remote Control Programming Codes,
continued
Cable Boxes, continued
SCIENTIFIC ATLANTA
SIGNATURE
SLMARK
SPRUCER
STARCOM
STARGATE
TELEVIEW
TOCOM
TOSHIBA
UNIKA
UNITED CABLE
UNIVERSAL
VIDEOWAY
VIEWSTAR
ZENITH

DVD Players

DVD Brand
MITSUBISHI
AIWA
APEX
BOSE
DENON
FERGUSON
HARMAN KARDON
HITACHI
JVC
KENWOOD
MINTEK
NORDMENDE
ONKYO
ORITRON
PANASONIC
PHILIPS/MAGNAVOX
PIONEER
RCA/GE/PROSCAN
ROTEL
SABA
SAMSUNG
SAMPO
SHARP
SYLVANIA
SONY
THOMSON
TOSHIBA
V INC. (BRAVO D1)
YAMAHA
ZENITH

112, 113, 194
119,124,125,126,127,120,121,122
105,101
105
119,124,125,126,127,120,121,122
105
101,105
135,136
104
125
119,124,125,126,127,120,121,122
122
106
129,130
117,100
Code
003
261, 274
266, 283
286
250, 273
251
282, 288
270
257
271, 289
285
251
267, 280
263, 268
250
258, 253, 272, 290
252
251, 256
292
251
261
263
260
264
254, 278, 279
251
253
291
250, 272, 276, 287
259

Satellite Receivers/SAT/DTV
Brand
MITSUBISHI

Code
006 (same as 173)
ECHOSTAR/DISH NETWORK
175, 182, 183, 188
EXPRESS VU
175
G.E.
176
HITACHI
173, 181, 184
HNS (Hughes)
173
JVC (ECHOSTAR)
175
MAGNAVOX
171, 172
PANASONIC
174
PHILIPS
171, 172
PROSCAN
176, 179, 180, 185
RCA
176, 179, 180, 185
SAMSUNG - TERRESTRIAL 192
SONY
177
STAR CHOICE
173
TOSHIBA
170, 189, 190, 191
UNIDEN
171, 172
WEBTV
187
ZENITH/LG
193

106

Appendices

VCRs
VCR Brand
MITSUBISHI
AKAI
AUDIO DYNAMIC
BELL & HOWELL
BROKSONIC
CANON
CITIZEN
CRAIG
CURTIS MATHES
DAEWOO
DBX
DIMENSIA
EMERSON
FISHER
FUNAI
GE
GO VIDEO
GOLDSTAR
HITACHI
INSTANT REPLAY
JVC
KENWOOD
LXI
MAGNAVOX
MARANTZ
MARTA
MEMOREX
MGA
MINOLTA
MULTITECH
NEC
OLYMPIC
OPTIMUS
ORION
PANASONIC
PENNEY
PENTAX
PHILCO
PHILIPS
PIONEER
PROSCAN
QUASAR
RADIO SHACK
RCA
REALISTIC
SAMSUNG
SANSUI
SANYO
SCOTT
SEARS
SHARP
SIGNATURE 2000
SONY
SV2000
SYLVANIA
SYMPHONIC
TASHIRO
TATUNG
TEAC
TECHNICS
TEKNIKA
TOSHIBA
TOTEVISION

VECTOR RESEARCH

WARDS
YAMAHA
ZENITH

Code
001, 060, 067, 068, 061, 062, 002
049, 034, 035, 036
031
025,
040, 046
043, 045
026
025, 049, 026
065, 044, 047
063, 021, 044, 078
030, 031
065
063, 046, 038, 039, 023, 045, 062, 040
025, 028, 029, 027
047, 046, 040
053, 065, 044, 079
057, 069, 070, 071
026
043, 065, 020, 047
044, 043
030, 031, 076, 077
030, 026, 031
047, 026, 020, 027, 028, 025, 029
051, 043, 044
030, 031
026
044, 029
060, 067, 068, 061, 062
020, 065
067, 047
030, 031
044, 043
048, 041, 055, 026
046, 040
043, 044, 041, 042
044, 020, 065, 025, 030, 031
020, 031, 065
051, 044, 047, 043, 046, 040, 063
051, 043, 044
043
065, 020, 043, 044, 051, 066, 021,
022, 053
041, 042, 043, 044
053, 044, 025, 056, 029, 060, 047
020, 021, 022, 043, 044, 049, 051, 053,
065, 066
044, 025, 056, 029, 060, 047
057, 022, 053
046, 040
025, 029
021, 022, 029, 060, 067, 068, 046, 040
025, 026, 027, 028, 020
055, 056
047, 055
048, 049, 050, 073, 074, 075
047
051, 043, 044, 047
047
026
030, 031
030, 047, 031
041, 042, 043, 044
044, 047
021, 066
026
031
055, 056, 029, 064, 026
025, 030, 031
064, 026

Appendix D: Remote Control Programming Codes,
continued
IMPORTANT
Some manufacturers may change their
products, or they may use more than one
remote control system. If this is the case,
the TV remote control may not be able to
operate your VCR, DVD, cable box, satellite
receiver, or A/V receiver.
After entering the correct codes in each position of the
remote control, use the slide switch to select which
product will respond when an operational button is
pressed. Only one of the below devices is allowed for
each slide switch position.
TV position:
TV, NetCommand® Controlled Devices
Cable/SAT/DTV position:
Cable box
Satellite receiver
DTV receiver
VCR position:
VCR
DVD position:
DVD
LD Player
Audio position:
A/V receiver
Mitsubishi CD player
If you have a Mitsubishi A/V receiver, the audio position
may be used in conjunction with select Mitsubishi CD
players. Your audio position must be programmed to 010.

When your remote control has been programmed to
operate another manufacturer’s product, the function
performed on each layer can vary. The most common
functions are:
VCR
• POWER
• CHANNEL up/down
• PLAY
• REC
• PAUSE
• STOP
• FF/FWD
• REW/REV
Mitsubishi VCRs will be compatible with some
additional buttons
Cable Boxes and Satellite Receivers
• POWER
• CHANNEL up/down
• 0-9 number buttons (on some models)
• ENTER (on some models)
• CANCEL (on some models)
• ADJUST up/down/ left/right (on some models)
• GUIDE (on some models)
A/V Receivers
• POWER
• VOLUME
• MUTE
Mitsubishi A/V Receivers
• Direct Input Selection buttons: numbers, SQV
and QV (on some models)
Mitsubishi CD Players
(not all functions for all models)
• PLAY
• FF/FWD
• REW/REV
• PAUSE
• STOP
DVD and Laser Disc Players
(not all functions for all models)
• POWER
• MENU
• 0-9 number buttons (on some models)
• PLAY
• STOP
• ARROW up/down/left/right (on some models)
• FF/FWD
• REW/REV
• PAUSE
• CANCEL (on some models)
• ENTER
• CHANNEL (on some models)

Appendices

107

Appendix E: Device Control with NetCommand®

NetCommand Compatible Traditional Devices (Analog)
When Device Selection Menu is Displayed and the Device is Highlighted (Yellow Outline)
A/V RECEIVER

VCR

DVD

CABLE BOX/SAT

POWER

Power On/Off
(toggle)

GUIDE

Changes
between digital
and analog
audio

Changes VCR inputs

n/a

Changes antenna inputs (RCA
model DTC-100 only)

FORMAT

n/a

Changes output between interlaced and progressive

Changes output between HD and
SD select models

Device
Remote
Control Button

When NetCommand® Compatible Traditional Device is Viewed or Played
A/V RECEIVER VCR

Device

DVD

CABLE/SAT

Channel up/down

Skip Forward/Backwards
Chapter or Track

Channel up/down Page up/down
when guide showing

number functions

Remote
Control Button

CH up/down
VOL up/down

Volume
Up/Down

MUTE

Mute On/Off

0-9 (digits)
QV

number functions
Last Channel Recall

DEVICE Menu

1st press Transport Menu,
2nd press Setup Menu display

Setup menu display or Action
function

Enter or select

HOME
ENTER
CANCEL

Counter Reset

GUIDE
ADJUST

Exit or return

Disc menu display

Channel Guide

up/down left/right

PLAY

Play

STOP

Stop

RECORD

Record

REW/REV

Rewind/Reverse

Reverse

FF/FWD

Fast Forward or Fast Play

Fast Play

108

Appendices

Appendix E: Device Control with NetCommand®, continued

IEEE 1394 Devices
When Device Selection Menu is Displayed and the Device is Highlighted (Yellow Outline)
TUNER/
CABLE BOX/
SAT

A/V DISC

DVCR

AMPLIFIER

POWER

Power On/Off
(toggle)

GUIDE

n/a

FORMAT

n/a

Device
Remote
Control Button

When an IEEE 1394 Device is Viewed or Played
Device

CABLE/SAT

TV Disc or A/V DISC

DVCR

AMPLIFIER

Channel up/down

Page up/down
(when track list is displayed)

Index search forward/reverse
(if supported by DVCR)

Remote
Control Button

CH up/down
VOL up/down

Volume Up/Down

MUTE

Mute On/Off

0-9 (digits)

number functions

Last Channel Recall

DEVICE Menu

n/a

Transport Menu redisplay

Device Menu

HOME

Exit menus/displays

ENTER

Enter or select

CANCEL

Cancel function

Cancel function or Counter
Reset

Cancel function

GUIDE

Digital Channel
Guide

Track or program list display

Program Guide

ADJUST

up/down left/right

Skip Forward 30 seconds
(during playback)
Skip Backwards 12 seconds
(during playback)
Skip to end or beginning of program
Page up/down in track list

up/down left/right

PLAY

Play

STOP

Stop

RECORD

Record

REW/REV

Reverse picture scan or Slow Play

Reverse or Slow Play

FF/FWD

Fast picture scan or Fast Play

Fast Play

Search by time
(when followed by ENTER)

up/down left/right

Appendices

109

Appendix F: NetCommand® Specialized Device Keys
A/V
RECEIVER

CABLE
or SAT

VCR

DVD

LEARNING SCREEN
CHECK BOX NAME

FUNCTION

NAME ON TV REMOTE

Power*

Power On or Power On/Off

POWER**

Power (Off)*

Power Off

POWER**

Volume Up

VOL

Volume Down

VOL

Mute

MUTE

Analog to Digital*

Analog/Digital Switch

GUIDE**

Digital to Analog*

Digital/Analog Switch

GUIDE**

Input (1-7)

AVR Input Select

Automatic (when
device is selected)

Channel Up

Channel Scan Up

CHAN

Channel Down

Channel Scan Down

CHAN

X
X

Recall

Last Channel Recall

Guide

GUIDE

Adjust Up

Arrow/move Up

ADJUST

Adjust Down

Arrow/move Down

ADJUST

Adjust Left

Arrow/move Left

ADJUST

Adjust Right

Arrow/move Right

ADJUST

Enter

Enter/Select

ENT

Device Menu or Setup Menu

DEVICE MENU

Cancel

Cancel or Exit

CANCEL

Info

Status Information Display

INFO

Page Up

Guide Page Up

CHAN

***

Page Down

Guide Page Down

CHAN

***

Play

PLAY

Stop

STOP

Forward

Fast Forward/Fwd Search

Rewind

Rewind/Reverse Search

REW

Pause

PAUSE

Record

REC

Enter (digits)†

Enter for channel numbers

ENT

Low Speed Out*

Low Speed 480i out

FORMAT**

High Speed Out*

Hi Speed 480p/1080i out

FORMAT**

1,2,3,4,5,6,7,8,9,0

Input

Input Change

GUIDE**

Sub channel separator‡

Digital Sub channel

CANCEL

Chapter +

Chapter Skip Forward

CHAN

Chapter -

Chapter Skip Reverse

CHAN

These are paired functions (e.g. Power and Power Off). When the original remote control uses a single button for both functions,
learn only the first of the paired functions.
† If there are two Enter keys, learn the Enter key used for channel selection here . The ENT button on the remote sends the correct
IR code when digits are entered.
‡ Learn the subchannel separator if a special key is used to add a separator (dash or dot) in a digital channel. Press the CANCEL
button on the remote to add the separator
** This function is performed only when the Device Selection Menu is displayed and the device icon is highlighted.
*** Channel Up/Down as Guide Page Up/Down happens only after pressing GUIDE and returns to channel functions after pressing
ENTER or CANCEL.

110

Appendices

Appendix G: Cleaning and Service
IMPORTANT
DO NOT use any kind of abrasive cleaner on
the surface of the TV screen.

Cleaning

Normally, light dusting with a dry, non-scratching duster will keep your TV clean. If cleaning beyond this is needed,
please use the following guidelines:

First, turn off the TV and unplug the power cord from the power outlet.

Top and Sides of the TV:
•

Gently wipe down your TV with a soft, non-abrasive cloth such as cotton flannel or a clean cloth diaper, lightly
moistened with water. Dry with a second dry, soft, non-abrasive cloth.

•

For oily dirt, add a few drops of mild liquid detergent, such as dishwashing detergent, to the water used to moisten
the cloth. Rinse with a second cloth moistened only with water. Dry with a third dry, soft, non-abrasive cloth.

Screen:
•

Follow the instructions for the top and sides, however, wipe gently in an up and down motion, following the grooves
in the screen.

•

Clean the entire screen evenly, not just sections of the screen.

•

Do not allow liquid to drip down the grooves of the screen, as some liquid may enter the TV between the screen and
the screen frame.

•

You may purchase Mitsubishi Screen Cleaner, part number CLEANER-VSS, by calling (800) 553-7278.

General Cleaning Warnings:
•

DO NOT allow liquid to enter the TV through the ventilation slots or any crevice.

•

DO NOT use any strong or abrasive cleaners as these can scratch the surfaces.

•

DO NOT use any cleaners with ammonia, bleach, alcohol, benzine, or thinners as these can dull the surfaces.

•

DO NOT spray liquids or cleaners directly on the TV’s surfaces.

•

DO NOT scrub or rub the TV harshly. Wipe it gently.

Service

If you are unable to correct a problem with your TV, consult your Mitsubishi dealer or a Mitsubishi Authorized Warranty
Service Center.
•

DO NOT adjust any controls other than those described in this Owner’s Guide.

•

DO NOT remove the protective back cover of your TV.

Menus not described and shown in this owner’s guide are designed for factory use and for authorized service
personnel. Damage caused to the TV by non-authorized changes or changes to these menus made by non-authorized
persons are not covered under warranty.

Appendices

111

Appendix H: Lamp Cartridge Replacement
CAUTION
BURN DANGER!

During normal operation, the surfaces inside
the TV near the lamp are extremely hot.
TOUCH THE LAMP CARTRIDGE BY THE HANDLE ONLY

Do not touch the glass parts of the lamp cartridge.

CAUTION: If the television is on, press POWER to turn it off. Allow the television to cool for
one hour before attempting to replace the lamp cartridge.
LAMP

The light source for this television is a lamp, which is part of a lamp cartridge assembly. The actual life of the lamp
in this television can vary, based on the lamp itself, the air temperature around the TV while it is operating, and your
viewing patterns. Warmer air or poor ventilation shortens the lamp life, as does turning the television on and off
frequently.
When the end of the lamp’s life is approaching, the TV displays a warning message for one minute when you power on
the TV. The message will reappear the next five times you turn on the TV. After you change the lamp cartridge, you
must reset the lamp reminder through the TV Setup menu. Otherwise, the warning message will appear again before
necessary. Mitsubishi warrants the lamp for one (1) year from the date of original TV purchase at retail.

TO ORDER A NEW LAMP:
While Under Warranty

After Warranty
Call (800) 553-7278. Order a new lamp for your
TV model as shown below.

Call (800) 332-2119. Please have model number,
serial number, and TV purchase date available.

TV Model Number

Lamp Part Number

WD-52628
WD-62628

915P026010

WD-73727

915P027010

WARNING:

Do not remove the lamp cartridge immediately after turning off the television. You may get burned because of the
lamp’s high temperature. Allow the television to cool for one hour before attempting to replace the lamp cartridge.
Do not remove the lamp cartridge except when replacing it. Careless treatment can result in injury or fire.
Do not touch the lamp glass element. It may be very hot and break, causing injuries or burns.
Be sure not to insert any metal or flammable object into the lamp cartridge opening, as it may cause fire or electrical
shock. If any object is inserted into the opening, unplug the AC cord of the TV and contact your dealer for service.
Install the lamp cartridge securely. Failure to do so may cause a fire.
Do not touch the lamp glass elements. Oils from your fingers may cause premature lamp failure.
The lamp in this product contains mercury. Disposal of mercury may be regulated due to environmental considerations.
For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance at:
www.eiae.org.

IMPORTANT
Reset the lamp hours through the TV setup menu each time you replace the lamp cartridge.
Otherwise, the lamp warning message will reappear sooner than necessary.

112

Appendices

Appendix H: Lamp Cartridge Replacement, continued
WARNING

THE GRILLE/COVER IS PROVIDED WITH AN
INTERLOCK TO REDUCE THE RISK OF EXCESSIVE
ULTRAVIOLET RADIATION. DO NOT DEFEAT
ITS PURPOSE OR ATTEMPT TO SERVICE THE
TV WITHOUT REMOVING THE GRILLE/COVER
COMPLETELY.
1. Turn TV power off and allow the lamp to cool at least
one hour before proceeding.
2. After the lamp has cooled, remove the plastic air
exhaust grille/cover by removing two screws with a #2
(large) Phillips screwdriver. See figure 1.
3. With a large flat-blade screwdriver, loosen the three
shiny screws securing the lamp cartridge until they
disengage from the mating threads. These are
captive screws and cannot be separated from the
lamp cartridge.

Figure 1.

4. Fully open up the bag supplied with the replacement
lamp and set the opened bag aside. If no bag was
supplied, use any available small paper bag.
5. Grasp the wire handle of the lamp cartridge and
pull the old cartridge straight out towards you. See
figures 2 and 3. Note the orientation of the cartridge.
CAUTION: Do not tilt or rotate the cartridge, as small
glass fragments may fall out.
6. Without tilting or putting down the lamp cartridge,
insert it into the opened bag. Close the bag while
being careful that no glass particles fall out.

Figure 2.

7. Do not touch the glass parts of the new lamp
cartridge. Insert the new cartridge into the TV in the
same orientation as the old cartridge. Push on the
cartridge housing until it is fully seated.
8. With either your fingers or the screwdriver, gently
tighten the three screws. If using a screwdriver,
use only two fingers for final tightening. AVOID
OVERTIGHTENING!
9. Replace the plastic grille/cover and retaining screws.
10. WASH YOUR HANDS THOROUGHLY, AS THIS LAMP
CONTAINS MERCURY.
11. Contact your local authorities or the Electronic
Industries Alliance at www.eiae.com for
lamp-disposal or recycling instructions. Do not
dispose of the old lamp with common trash.

Handle
Figure 3.

12. Reset the Lamp Reminder from the TV Setup menu
as follows:
a. Press TV MENU to open the Setup menu.
b. Move the highlight to Lamp Reminder.
c. Press ENTER twice.

Appendices

113

Appendix I: Recording and Viewing Combinations

The tables in this appendix show which program sources you can watch while a recording is in progress.

Analog VCR Connected to Audio and Video Record Outputs
You can watch any one of these (viewing device)
When recording this
(source device)

Same as
Recording

Different
Antenna or
Channel

Input 1–3
Devices

Component
1–3 Devices

IEEE-1394
Device

HDMI
Device

Ant-1 Air/Cable
Analog Channel

Yes

Ant-1 Air/Cable
Digital Channel

Yes

Ant-1 CableCARD
Analog Channel

Yes

Ant-1 CableCARD
Digital Channel

Yes

Ant-2 Air/Cable
Analog Channel

Yes

Ant-2 Air/Cable
Digital Channel

Yes

Input 1–3
Video or S-Video Devices

Yes

IEEE-1394 Device

Yes

Yes,
same as
recording

Yes

114

Component 1–3

Cannot record from this source

HDMI Device

Cannot record from this source

Appendices

Appendix I: Recording and Viewing Combinations

Digital VCR or A/V Disc Connected to IEEE-1394 Port
When recording this
(source device)

You can watch any one of these (viewing device)
Same as
Recording

Ant-1 Air/Cable
Analog Channel
Ant-1 Air/Cable
Digital Channel

Yes

IEEE-1394
Device

HDMI
Device

Yes

Cannot make digital recordings from this source
Yes

Input 1–3
Video or S-Video Devices
IEEE-1394 Device

Component
1–3 Devices

Cannot make digital recordings from this source

Ant-2 Air/Cable
Analog Channel
Ant-2 Air/Cable
Digital Channel

Input 1–3
Devices

Cannot make digital recordings from this source

Ant-1 CableCARD
Analog Channel
Ant-1 CableCARD
Digital Channel

Ant-1/Ant-2
Channels

Yes

Cannot make digital recordings from this source
Yes

Yes

Component 1–3

Cannot record from this source

HDMI Device

Cannot record from this source

Appendices

Yes

115

Trademark and License Information
LICENSOR’S SUPPLIERS DO NOT MAKE OR PASS ON TO END USER OR ANY OTHER THIRD PARTY, ANY EXPRESS,
IMPLIED OR STATUTORY WARRANTY OR REPRESENTATION ON BEHALF OF SUCH SUPPLIERS, INCLUDING, BUT
NOT LIMITED TO THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, TITLE, MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE.
CableCARD™ is a trademark of Cable Television Laboratories, Inc.
CompactFlash® and CF are trademarks of the CompactFlash Association.
DCR™ Certification Logo is a trademark of the Consumer Electronics Association.
Digital Light Processing™ and DLP™ are trademarks of Texas Instruments.
Manufactured under license from Dolby Laboratories. Dolby® and the double-D symbol are registered trademarks of
Dolby Laboratories.
DTVLINK™ Certification Logo is a trademark of the Consumer Electronics Association.
Firewire® is a trademark of Apple Computer, Inc. registered in the U.S. and other countries.
HDMI™ the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
Lifestyle® 28 is a trademark of the Bose Corporation.
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual
property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for
home and other limited pay-per-view uses only unless otherwise authorized by Macrovision. Reverse engineering or
disassembly prohibited.
Memory Stick™ and Memory Stick PRO™ are trademarks of Sony Corp.
Microdrive® is a registered trademark of Hitachi Global Storage Technology, Inc. in the United states and/or other
countries.
This product includes technology owned by Microsoft Corporation and cannot be used or distributed without a license
from Microsoft Licensing, Inc.
MultiMediaCard™ is trademark of Infineon Technologies and licensed to the MultiMediaCard Association.
The PanelLink Cinema Partners logo and the “PanelLink Cinema,” “PLC” and “PLC Content Ready” word
marks are trademarks of Silicon Image, Inc. and are used under a license from Silicon Image, Inc or
PanelLink Cinema, LLC.
Playstation® 2 is a trademark of the Sony Corporation.
SD logo is a trademark.
SmartMedia™ is a trademark of Toshiba Corp.
In the United States, TV GUIDE and other related marks are registered marks of Gemstar-TV Guide International, Inc.
and/or one of its affiliates.
The TV Guide On Screen® system is manufactured under license from Gemstar-TV Guide International, Inc. and/or one
of its affiliates.
The TV Guide On Screen® system is protected by one or more of the following issued United States patents:
6,498,895; 6,418,556; 6,331,877; 6,239,794; 6,154,203; 5,940,073; 4,908,713; 4,751,578; 4,706,121.
XBox™ is a trademark of the Microsoft Corporation.
MonitorLink™, NetCommand®, ViewPoint®, QuickView™, SuperQuickView™, PerfectColor™ , MediaCommand™,
ChannelView™ are trademarks of Mitsubishi Digital Electronics America, Inc.

116

Trademark and License Information

MITSUBISHI TV SOFTWARE
END-USER LICENSE AGREEMENT FOR EMBEDDED SOFTWARE
IMPORTANT – READ CAREFULLY: This License Agreement is a legal agreement between you (either an individual or an entity) and
Mitsubishi Digital Electronics America, Inc. (MDEA) for all software pre installed and/or provided along with this television (“Software”).
By utilizing this television and Software, you agree to be bound by the terms of this License Agreement.
The Software is protected by United States copyright laws and international treaty provisions, as well as other intellectual property
laws and treaties. The Software is licensed, not sold.
1.
LICENSE GRANT. MDEA grants you a non-exclusive, non-transferable, limited right and license to use one copy of the
Software only with the Mitsubishi television model that included this owner’s guide and owned by you.
2.
RIGHTS AND LIMITATIONS.
Software Not for Resale. You may not resell or otherwise transfer for value the Software, except in conjunction with a sale of the TV
that Software has been pre installed.
Prohibition on Reverse Engineering, Decompilation and Disassembly. The Software contains trade secrets or other proprietary
material in its human perceivable form and to protect them, you may not reverse engineer, decompile, or disassemble, or otherwise
reduce the Software to any human perceivable form, except to the extent that the foregoing restriction is expressly prohibited by
applicable law.
Separation of Components. The Software is licensed as a single product. Its component parts may not be separated for use on more
than one TV.
No Rental. You may not rent, lease, lend, or sublicense the Software.
Trademarks. This License Agreement does not grant you any rights to any trademarks of MDEA.
3.
VIOLATIONS. You understand that any use, copying or transfer of the Software, except as permitted pursuant to this License,
may subject you to serious criminal and civil penalties including damages and an award to MDEA of attorneys’ fees in connection with
any violation of this License. You further understand that you may be held legally responsible for any copyright infringement or other
violation of intellectual property rights that is caused, encouraged, or induced by your failure to abide by the terms of the License.
This license is effective until terminated, and will terminate immediately without notice from MDEA or judicial resolution if you fail to
comply with any provision of this License.
4.
COPYRIGHT. All title and intellectual property rights in and to the Software (including but not limited to any images,
photographs, animations, video, audio, music, text, and “applets” incorporated into the Software), and any accompanying printed
materials are owned by or licensed to MDEA. All title and intellectual property rights in and to the content which may be accessed
through use of the Software is the property of the respective content owner and may be protected by applicable copyright or other
intellectual property laws and treaties. This License Agreement grants you no rights to use such content, except that you own the
media on which the Software is recorded, but MDEA and its licensors retain ownership of the Software itself. All rights not expressly
granted are reserved by MDEA.
5.
EXPORT RESTRICTIONS. MDEA is licensing the Software for use within the United States. You agree that you will not
export or re-export the Software. You specifically agree not to export or re-export the Software: (i) to any country to which the U.S.
has embargoed or restricted the export of goods or services, which currently include, but are not necessarily limited to Cuba, Iran,
Iraq, Libya, North Korea, Sudan, and Syria, or to any national of any such country, wherever located, who intends to transmit or
transport the Software back to such country; (ii) to any person or entity who you know or have reason to know will utilize the Software
in the design, development, or production of nuclear, chemical, or biological weapons; or (iii) to any person or entity who has been
prohibited from participating in U.S. export transactions by any federal agency of the U.S. government. You warrant and represent
that neither the BXA nor any other U.S. federal agency has suspended, revoked, or denied your export privileges.
6.
DISCLAIMER OF WARRANTY. EXCEPT AS OTHERWISE PROVIDED IN THIS LICENSE OR IN THE LIMITED
WARRANTY APPLICABLE TO THE TV, MDEA MAKES NO OTHER WARRANTIES OF ANY KIND WHATSOEVER REGARDING
THE SOFTWARE AND HEREBY EXPRESSLY DISCLAIMS ALL WARRANTIES OF ANY KIND WHATSOEVER, EXPRESS OR
IMPLIED, WITH RESPECT TO THE SOFTWARE. ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXPRESSLY
DISCLAIMED BY MDEA. IN NO EVENT SHALL MDEA BE LIABLE TO YOU OR ANY THIRD PARTIES, IN CONTRACT, IN TORT
OR OTHERWISE, FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND OR
NATURE. BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IMPLIED WARRANTIES,
THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
7.
LIMITATION OF LIABILITY. MDEA SHALL NOT, UNDER ANY CIRCUMSTANCES BE LIABLE TO YOU OR ANY THIRD
PARTIES FOR ANY DAMAGES OF ANY NATURE, WHETHER INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL
OR OTHERWISE, INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOST PROFITS, LOSS OF GOOD WILL OR
EXPENDITURES MADE OR COMMITTED FOR IN RELIANCE ON THE CONTINUATION OF THIS LICENSE. YOU AGREE
THAT NEITHER MDEA’S BREACH OF THIS LICENSE NOR ITS FAILURE TO REPAIR A DEFECT, ERROR OR BUG SHALL
CONSTITUTE A FAILURE OF THE ESSENTIAL PURPOSE OF THIS LICENSE. BECAUSE SOME JURISDICTIONS DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE
LIMITATIONS MAY NOT APPLY TO YOU. MDEA’s liability to you for direct damages for any cause whatsoever and regardless
of the form of the action, will be limited to the money paid by you for the TV (based on fair market value of the TV) that
caused the damages.
8.
GENERAL. This License Agreement will be governed by the laws of the State of California.

WARNING: This product contains chemicals known to the State of California to cause cancer and/or birth defects or
other reproductive harm.

Trademark and License Information

117

Mitsubishi DLP™ Projection Television Limited Warranty
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. (“MDEA”) warrants as follows to the original purchaser of this
television from an authorized MITSUBISHI Audio/Video Dealer, should it prove defective by reason of against defects
arising from improper workmanship and/or material:
a. Parts. The lenticular (i.e. front picture) screen is warranted against defects in materials and workmanship for a period
of thirty (30) days from the date of the original purchase at retail. The lamp and all other parts (except any software
incorporated into this television) are warranted for a period of one (1) year from the date of the original purchase at retail.
We will repair or replace, at our option, any defective part without charge for the part. Parts used for replacement may
be replaced with those of like kind and quality and may be new or remanufactured. Parts used for replacement are
warranted for the remainder of the original warranty period.
b. Embedded Software. MDEA warrants that all software incorporated into this television set (the “Embedded
Software”) will perform in accordance with the functional description of Embedded Software in all material respects, but
MDEA does not warrant that the Embedded Software is error-free. MDEA also does not warrant that the Embedded
Software will be compatible under IEEE 1394 AV/C and HAVi software standards with products produced by any other
manufacturer. The limited warranty contained in this section shall continue for a period of one (1) year from the date of
the original purchase at retail. If, after prompt notice within the warranty period, MDEA determines that the Embedded
Software has failed to perform in accordance with such functional description in all material respects and if such failure
is not due to accident, misuse, modification or misapplication of the Embedded Software, then MDEA shall modify or
replace the nonconforming Embedded Software at no charge to you, which at MDEA’s sole discretion may be fulfilled
by means of modification or replacement software contained on a replacement memory card for Customer installation.
The foregoing shall be MDEA’s sole obligation to you under this limited warranty. All rights under this limited warranty
on the Embedded Software also subject to your acceptance of and compliance with the terms of the Software License
Agreement applicable to this television, and this limited warranty on the Embedded Software shall be null and void if the
Embedded Software is modified or changed in any manner except as specifically authorized by MDEA.
c. Labor. For thirty (30) days after the original purchase at retail, we will repair or replace, at our option, the lenticular
screen if it proves defective. For certain items that are designed to be replaced by the consumer, including (but not
limited to) some Embedded Software, the consumer is solely responsible for any replacement labor. For all other parts,
we will provide the labor for a warranty repair by an authorized MITSUBISHI service center without charge for one (1)
year from the original date of purchase at retail.
d. Notice. To obtain warranty service, you must notify an authorized MITSUBISHI service center of any defect within
the applicable warranty time period.
e. This DLP Projection Television uses a single DLP chip to create the screen image. This technology creates the image
using small dots, or picture elements (pixels). Your DLP Projection TV is manufactured to a high level of performance
and quality, in fact, 99.99% perfect in the number of properly functioning pixels. As in other display technology,
sometimes a pixel is continuously active, inactive or the incorrect color. Our standard is clear; MDEA warrants only that
the percentage of properly functioning pixels will be not less than 99.99% of all pixels.
BEFORE REQUESTING SERVICE, please review the instruction booklet to insure proper installation and correct
customer control adjustment. If the problem persists please arrange for warranty service.
1. TO OBTAIN WARRANTY SERVICE:
a. Contact your nearest authorized MITSUBISHI service center, whose name and address can be obtained from your
MITSUBISHI dealer, by writing at the address provided below, calling MDEA at the 800-332-2119, or by using the
support feature of our website at www.Mitsubishi-tv.com.
b. Warranty service will be provided in your home or, if required, at an authorized service shop, provided that your
television is located within the geographic territory customarily covered by an authorized MITSUBISHI service center. If
not, you must either deliver your television to an authorized service location at your own expense, or pay for any travel
and/or transportation costs the service center may charge to and from your home. Actual service labor will be provided
without charge.
c. Proof of purchase date from an authorized MITSUBISHI dealer is required when requesting warranty service. Present
your sales receipt or other document which establishes proof and date of purchase. THE RETURN OF THE OWNER
REGISTRATION CARD IS NOT A CONDITION OF COVERAGE UNDER THIS LIMITED WARRANTY. However, please
return the Owner Registration Card so that we can contact you should a question of safety arise which could affect you.

118

d. To obtain a replacement lamp during the warranty period, please contact the MDEA Consumer Relations Department
at (800) 332-2119. After the warranty period you may order the lamp directly from the MDEA Parts Department at (800)
553-7278.
2. THIS LIMITED WARRANTY DOES NOT COVER:
a. Up to .01% pixel outages (small dot picture elements that are dark or incorrectly illuminated).
b. Damage to the lenticular screen or Fresnel lens, screen frame, cosmetic damage or to any other damage where
such damage is caused by unauthorized modification, alteration, repairs to or service of the product by anyone other
than an authorized MITSUBISHI service center; physical abuse to or misuse of the product (including any failure to
carry out any maintenance as described in the Owner’s Guide including air filter cleaning or any product damaged by
excessive physical or electrical stress); any products that have had a serial number or any part thereof altered, defaced
or removed; product use in any manner contrary to the Owner’s Guide; freight damage; or any damage caused by acts
of God or other factors beyond the reasonable control of MDEA, such as power surge damage caused by electrical
system or lightning. This limited warranty also excludes service calls where no defect in the product covered under
this warranty is found, service calls related to unsatisfactory audio or visual reception or signal unless caused by a
defect in the product that is covered under this limited warranty, all costs, expenses or any other damages arising from
product installation, or set-ups, any adjustments of user controls (including contrast, brightness, color, tint, fine tuning,
sharpness), other adjustment necessary to prepare the unit for display or use, connection with any external audio
receiver, antenna, cable or satellite systems, or service of products purchased or serviced outside the U.S.A. Please
consult the operating instructions contained in the Owner’s Guide furnished with the product for information regarding
user controls.
3. ANY EXPRESS WARRANTY NOT PROVIDED HEREIN, AND ANY REMEDY WHICH, BUT FOR THIS PROVISION,
MIGHT ARISE BY IMPLICATION OR OPERATION OF LAW, IS HEREBY EXCLUDED AND DISCLAIMED. THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR ANY PARTICULAR PURPOSE ARE EXPRESSLY
LIMITED TO A TERM OF ONE YEAR.
4. UNDER NO CIRCUMSTANCES SHALL MDEA BE LIABLE TO PURCHASER OR ANY OTHER PERSON FOR ANY
INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER ARISING OUT OF BREACH OF WARRANTY,
BREACH OF CONTRACT, OR OTHERWISE.
5. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental,
special, or consequential damages, so the above limitations or exclusions may not apply to you.
6. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to
state.

MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC.
9351 Jeronimo Road
Irvine, CA 92618-1904

119

Index
A

A/V Memory Reset. See Reset
A/V Receiver
Adding 45
Connecting 28
Inputs 45
Input Learn Screen 46
Learn Screen 46
A/V Reset. See Reset
A/V Settings Descriptions
Audio 80
Video 81
Accessories, TV 10
Add Device. See NetCommand
Advanced Learn Screen, [Device] 50
Antenna inputs (ANT-1 MAIN, ANT-2
AUX) 16
Antenna with Leads, Connecting 25
Audio/Video Menu 66, 79
Audio Inputs 16

Back Panel (illustrated) 16
Batteries. See Remote Control

CableCARD™ 11, 17, 23
CableCARD™ Menu 59
Cable Box 53, 108
Connecting 24, 27
Captions Menu 66, 74
Change Device Screen.
See NetCommand
Channels 68, 72, 102. See also SQV
and PIP viewing 86
Changing 72
Memorizing 67
Name 72
ChannelView 60
Channel Menu 72
Cleaning and Service 111
Clock
Set Date, Time 67
Color Adjustments 81
Component Inputs (YPbPr) 16
Computer. See PC
Connecting: Helpful Hints 35
Connection for [Device] Screen 50
Connection Screen 55
Copy-Protected Material 62

120

Index

Date. See Clock
Daylight Savings Time 68
Demo Mode 20
Device Menu 59
Device Selection Menu 58
Digital Audio Output 17
Display Formats 87
DTV Link 17
DVD Player with Component Video,
Connecting 29
DVI Analog Audio 16
DVI Device 29

Film Mode 79
Format Definitions 87
Front Button Lock 77
Front Control Panel 12

GUIDE Key (button) 13, 14, 35, 60

HDMI Device 30
HDMI Input 17
HDTV Receiver with Component
Video, Connecting 30

Icon Order 69
IEEE 1394
Adding IEEE 1394 Devices Automatically 54
and NetCommand 53
Compatible IEEE 1394 Devices
33
Connecting IEEE 1394 Devices
33
IEEE 1394 Device Type Screen
55
Inputs 17
Name for 1394 Device Screen
54
New 1394 Device Screen 54
Indicator Lights 95
Front Panel 12
Lamp Indicator 12
Power/Timer 13
Status 13

Inputs (Audio/Video) 16
IR (Infrared)
IR Code for [Device] Screen 51
IR Emitter NetCommand® 16,
32

JPEG Picture Thumbnails (Media
Dialog Box) 84

Lamp Cartridge Replacement 112
Lamp Indicator. See Indicator Lights
Lamp Reminder 68
Language 67
“Learn” Feature
A/V Receiver 45, 46
Code Reference Chart 105
Description 22, 38, 39
Device 50
Device Key Reference Chart 110
GUIDE Key 35
IEEE 1394 Devices 55
Troubleshooting 93, 94
Learn Screen, [Device] 49
Lock
Front Button Lock 77
Lock TV by Time 77
V-Chip Options 76

Memorize Channels. See Channels
Memory Cards 11
Media Setup Menu 85
Memory Card Reader 18, 19, 84
Playback 84
Mute
Audio 74, 102
MUTE key 14

Video Mute 79

Name Screen 47, 50
NetCommand
Add Device 48
Change Device 52
Connecting External Devices 22
Delete Device 52
Description 11
Device Control (reference chart)
108

Device Setup Screen 43
Edit NetCommand Screen 48
Initial Setup 42
NetCommand Menu 69
Pre-Memorized Devices 39
Specialized Device Keys 110

On-Screen Information 102

Pass Code
Resetting 103
Setting 76
PC 16, 17, 48, 54, 87
Connecting 31
Viewing 81, 89
Peer-to-Peer Connection 63
PerfectColor 81
PIP (Picture in Picture) 86
PIP Device Selection Menu 58
Playlist Menu, MP3 or WMA7 85

QV (QuickView™) 14

Recording
Analog VCR and Viewing 114
Cancel Current Recordings 71
Default Digital (Record) Device
71
Digital VCR or A/V Disc and
Viewing 115
Record List Screen 61, 71
REC Button 14, 60, 61, 70, 93,
97
Setup 61, 70
Time-Delayed 61, 70
VCR Recording from an Antenna
or Cable Source 61
Remote Control
and NetCommand® 39
Batteries 15
Functions 14
Programming 105
Programming Codes (reference
chart) 105
Transport Buttons 69

121

Index

Reset
A/V (all settings) 13
A/V Memory (for individual devices) 79
DVCR Counter 109
Lamp Reminder 68
Pass Code 103
PerfectColor 81
Remote Control 15
Reset Menu 20
System Reset Button 12, 20, 92
VCR Counter 108
Review Screen 44
RF Connection for Cable Screen 51

S-Video 28
Satellite Receiver 14, 22, 28, 30, 32,
39, 48, 53, 54, 60, 106, 107
Search A/V Disc. See A/V Discs
Setup Menu 66, 67
Signal Definitions 87
Speakers, TV 79
Specifications, TV 100
SQV (SuperQuickView™) 73
Stand Requirements 2
Status Indicator. See Indicator Lights
Stereo. See A/V Receiver
System Reset. See Reset

Time. See Clock
Timer 68
Time Zone 68
Track List Screen 64
Transport Menu 69
TV Guide On Screen 11, 14, 16, 24,
71, 72
Access Requirements 2
Setup 43

V-Chip 78
Bypassing the V-Chip Lock 103
Ratings 78
V-Chip Lock Menu 66, 76
V-Chip Menu 76

VCR 14, 16, 33, 54, 55, 58, 60, 94
and NetCommand Control 108,
109
Connecting 26, 27
NetCommand Default Input 22
NetCommand Pre-Memorized
Models 39
NetCommand Specialized Device Keys 110
Programming Codes 106
Restrictions for Traditional VCRs
62
VCR for Recordings Screen 51
Video Inputs 16
Video Settings 81

Wall Outlet Cable 24

Website:

www.mitsubishi-tv.com

E-mail:

MDEAservice@mdea.com

To order replacement or
additional remote controls, lamp
cartridges, or Owner’s Guides,
call
800-553-7278
For questions, call Consumer
Relations at
800-332-2119

Written and Printed in U.S.A.

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.1-c037 46.282696, Mon Apr 02 2007 18:36:42
Create Date                     : 2009:01:07 13:17:13-08:00
Modify Date                     : 2009:01:07 13:18:13-08:00
Metadata Date                   : 2009:01:07 13:18:13-08:00
Creator Tool                    : Adobe InDesign CS3 (5.0.3)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 10552 bytes, use -b option to extract)
Version ID                      : 1
Instance ID                     : uuid:20920404-1be6-4159-aca7-0c6139183358
Document ID                     : adobe:docid:indd:2b74799a-dd00-11dd-9891-f06f995fa595
Rendition Class                 : proof:pdf
Derived From Instance ID        : 2b747999-dd00-11dd-9891-f06f995fa595
Derived From Document ID        : adobe:docid:indd:ff4d18a2-a5dc-11dd-bb17-ec748d53e1c6
Derived From Version ID         : 1
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 150.00, 72.00, 150.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 150.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 150.00, 72.00, 72.00, 72.00, 150.00, 72.00, 72.00, 72.00, 72.00, 150.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 300.00, 300.00, 300.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 300.00, 300.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 150.00, 72.00, 150.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 150.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 150.00, 72.00, 72.00, 72.00, 150.00, 72.00, 72.00, 72.00, 72.00, 150.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 300.00, 300.00, 300.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 300.00, 300.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:df18a3e5-3e32-4a08-bb13-394ebf2aaa95, uuid:945740bf-a76e-4c0b-bff6-986b2531d842, uuid:6c6a8436-92b3-4f79-b637-a62162d388db, uuid:164e9aa0-e1b9-4cb4-8eca-244d587e73c8, uuid:069846ba-fe60-46bc-8a65-ccb63ddc76f2, uuid:7ec6975b-de7c-4dd1-8701-f0f8c603b986, uuid:9c584065-b125-4fd8-9b11-773cf8aabad4, uuid:d2792d2c-f330-4eff-899d-3d8dabaabc33, uuid:d2792d2c-f330-4eff-899d-3d8dabaabc33, uuid:d971a55b-b6a6-4292-a7ee-7aaacb93362d, uuid:cd334b6d-2856-4235-9d3b-9640011e3c3e, uuid:a1b9562e-5435-4883-8aab-2e35ab889167, uuid:1e2597b1-4875-4af1-8be1-aabdb794ffe9, uuid:05d1fd01-9c53-4f5e-bb43-0897c8174717, uuid:0d58a436-f17d-4b74-866c-ca7f84393b7e, uuid:bb68e9f8-4bce-4676-a49c-b5063dbe250d, uuid:7e97cb6a-ef9b-4b4c-befc-85528b37916a, uuid:69c391f2-fc2c-459b-ba15-e2459f75c0eb, uuid:b3877d7d-3999-400c-88f5-7924939fab6a, uuid:bdd4117b-63da-11d7-87c4-849b1cdb6749, uuid:9d547e65-8994-4825-9010-65b7e16bf80a, uuid:42a09c4d-b962-4742-bcd7-3f3eb5165d70, uuid:dfa657ee-ac38-4530-9127-026e07072588, uuid:a2155788-a2b1-4d0c-b523-dd9b361189f6, uuid:6bc808cb-8e31-4b48-858f-192dc19fe8a1, uuid:0ce1f1dd-d26c-4215-89dd-8ee3512492e3, uuid:b6124c53-db1a-403a-bbcf-7b155571e9d7, uuid:02b30c9f-6868-40e6-b2b7-f48cb7ae21ae, uuid:783ec969-4223-4407-9633-d4694824fbea, uuid:3d2c3cc7-617c-402d-8e4e-701b0638c254, uuid:1c18ec55-e210-4d58-82b8-500f6b5cc787, uuid:e64e6f2c-4ced-4f8f-8ef5-deef8531e7eb, uuid:8cb68ccb-2faa-42ea-9789-c4edf0aadfba, uuid:10393882-7521-4b4b-a5bd-9e88d4c91208, uuid:85346c0e-5dc7-4584-b935-44beafc680fb, uuid:d3230a2b-fde7-4154-8607-1f90324fadd0, uuid:a7058bb5-e8c5-4457-9393-7e3c39836685, uuid:e4d209e2-7b6f-43e4-9e7b-fc136fefdea0, uuid:3e3b741c-4629-45dc-9fd8-5707990cc6ad, uuid:ac8a9cd4-6ff6-4924-8654-75ef8fa03ff1, uuid:164e9aa0-e1b9-4cb4-8eca-244d587e73c8, uuid:6d771fb7-5ed7-435f-b13f-ae75ab024b0f, uuid:8614aa72-646a-11d7-9b17-e1042c5691bf, uuid:d24f72cc-6474-11d7-9d35-bbbbeee7c888, uuid:164e9aa0-e1b9-4cb4-8eca-244d587e73c8, uuid:164e9aa0-e1b9-4cb4-8eca-244d587e73c8, uuid:2f8fd1df-35c6-43dc-888c-b5c1a257a3e7, uuid:164e9aa0-e1b9-4cb4-8eca-244d587e73c8, uuid:164e9aa0-e1b9-4cb4-8eca-244d587e73c8, uuid:e9187aec-7547-11d9-928f-8a4b7ba0ef80, uuid:164e9aa0-e1b9-4cb4-8eca-244d587e73c8, uuid:b1ce30c9-9eac-11d8-9537-84d8b668b1c6, uuid:c62ed03e-a88d-11d9-b086-b82372aac7b7, uuid:60993933-ba70-11d8-a24b-ee230997191b, uuid:1108097a-c31b-11d9-a87d-d6cda2755a15, uuid:17d48b18-c3d6-11d8-b748-9e36488c084e, uuid:746f4f9b-c31a-11d9-a87d-d6cda2755a15, uuid:67ab2bbc-7a00-11d9-9db1-899ddf725e4c, uuid:c49be2cc-a88d-11d9-b086-b82372aac7b7, uuid:c4604804-a88d-11d9-b086-b82372aac7b7, uuid:21156e95-bcdc-11d9-9af2-f247f9d3322a, uuid:34dc3a9c-bdc1-11d9-94c7-c42c629ec111, uuid:c59afe6d-a88d-11d9-b086-b82372aac7b7, uuid:44054671-80b7-11d7-aa6c-8aa8a21f9719, uuid:c4ecf2c7-a88d-11d9-b086-b82372aac7b7, uuid:c76e4b5b-a88d-11d9-b086-b82372aac7b7, uuid:f1b07ca6-68d3-11d9-bbfe-f4cafaedb0a5, uuid:f126b405-68d4-11d9-bbfe-f4cafaedb0a5, uuid:b74cb3eb-be59-11d9-a4df-cf3786da8789, uuid:1710AFECFFDCDD118357CB8D8E1F9B48, uuid:34dc3a9c-bdc1-11d9-94c7-c42c629ec111, uuid:c7512e7d-aaa1-11d8-b439-e045639b9f62, uuid:138769b2-e4e3-11d9-99a8-dc306820847b, uuid:c4ecf2c7-a88d-11d9-b086-b82372aac7b7, uuid:34dc3a9c-bdc1-11d9-94c7-c42c629ec111, uuid:4cf5ef2d-c32b-11d9-a87d-d6cda2755a15, uuid:b1227a88-c32e-11d9-a87d-d6cda2755a15, uuid:b811b75c-4596-44fa-8296-0e270de603ec, uuid:1e8da508-c32c-11d9-a87d-d6cda2755a15, uuid:df9ecc96-89a2-11d8-ba66-d5db658352ef, uuid:aefcf379-bb4e-11d9-be12-b5c5fa77e95b, uuid:fa6a1152-7545-11d9-928f-8a4b7ba0ef80, uuid:aefcf379-bb4e-11d9-be12-b5c5fa77e95b, uuid:365abc18-b1c8-11d9-8ca1-d94f892a2deb, uuid:e9187aec-7547-11d9-928f-8a4b7ba0ef80, uuid:b0f41bf7-7546-11d9-928f-8a4b7ba0ef80, uuid:4460feb5-7549-11d9-928f-8a4b7ba0ef80, uuid:7cd6d718-754d-11d9-928f-8a4b7ba0ef80, uuid:b0f41bf3-7546-11d9-928f-8a4b7ba0ef80, uuid:9a607442-754b-11d9-928f-8a4b7ba0ef80, uuid:5e56ee83-754d-11d9-928f-8a4b7ba0ef80, uuid:1d6a4fac-754a-11d9-928f-8a4b7ba0ef80, uuid:60b1f6ed-e26c-11d9-8a53-905c1f583d8d, uuid:d901d88c-addf-11d9-a639-b5fcc20c06d6, uuid:05efae3b-9bf2-4992-9697-1e32d4f74a5a, uuid:b031eea0-4f88-4be8-9a79-1f2458cf354f, uuid:3465d23a-be4a-11d9-a4df-cf3786da8789, uuid:c5ddc043-a88d-11d9-b086-b82372aac7b7, uuid:5e56ee83-754d-11d9-928f-8a4b7ba0ef80, uuid:aefcf379-bb4e-11d9-be12-b5c5fa77e95b, uuid:fa6a1152-7545-11d9-928f-8a4b7ba0ef80, uuid:b0f41bf7-7546-11d9-928f-8a4b7ba0ef80, uuid:4460feb5-7549-11d9-928f-8a4b7ba0ef80, uuid:27ac1f84-a09a-11d9-ad90-f3e2cf3aad84, uuid:2088108d-754e-11d9-928f-8a4b7ba0ef80, uuid:b50cc615-d1e4-11d9-88d9-f706c20b34fa, uuid:e0f15672-e1b6-11d9-9060-83cbc1a69788, uuid:b0f41bf3-7546-11d9-928f-8a4b7ba0ef80, uuid:b1227a8e-c32e-11d9-a87d-d6cda2755a15, uuid:e8f7674e-a92d-46b7-81e7-f34ffcb6958e, uuid:b0bb0d92-3eee-11d7-bef3-c5f27bc5c157, uuid:b0bb0d92-3eee-11d7-bef3-c5f27bc5c157, uuid:b0bb0d8f-3eee-11d7-bef3-c5f27bc5c157, uuid:b0bb0d8c-3eee-11d7-bef3-c5f27bc5c157, uuid:71479862-3eee-11d7-bef3-c5f27bc5c157, uuid:71479862-3eee-11d7-bef3-c5f27bc5c157, uuid:71479862-3eee-11d7-bef3-c5f27bc5c157, uuid:712a7ea8-d61e-4bbc-9b37-b2aee83859e7, uuid:d9ffa00a-8688-44d3-b9cf-204822203531, uuid:e624063a-3b2b-47f8-95c9-08e708b89ed6, uuid:66362c63-dcf0-47ec-86fa-6f2159c68722, uuid:852d72db-3de0-4763-bec8-e446215d1e0a, uuid:fb62bf1c-6ed6-4842-a5ae-4dfb6f48bb6b, uuid:5f02099a-6940-447d-884e-7f3751976daa, uuid:b3c1a197-e9d4-4ec3-83fc-5f7160f0b03f, uuid:6c4eaeaa-e108-4b22-9173-24cd8c186dca, uuid:7147985f-3eee-11d7-bef3-c5f27bc5c157, uuid:7147985f-3eee-11d7-bef3-c5f27bc5c157, uuid:7147985c-3eee-11d7-bef3-c5f27bc5c157, uuid:6913f58d-7034-11d7-b9e8-ef9b06869058, uuid:452e45c7-b3c1-4087-9f68-55e6adc05b4a, uuid:edd8d375-0689-473b-8f21-507274f0c59b, uuid:6913f590-7034-11d7-b9e8-ef9b06869058, uuid:9321b721-3040-4a43-940b-f469f2ece9c1, uuid:8e9b362d-0b0f-4074-927c-c5ac8028f34b, uuid:5dc35731-7a7c-47c4-b9d8-38e43e6fbd23, uuid:d47f8893-e2c5-4d3e-a162-1eb53f855e92, uuid:6913f590-7034-11d7-b9e8-ef9b06869058, uuid:9321b721-3040-4a43-940b-f469f2ece9c1, uuid:f2a84c72-a88f-11d9-b086-b82372aac7b7, uuid:f2a84c72-a88f-11d9-b086-b82372aac7b7, uuid:ff3f0801-04d9-4060-a0d6-07e408dc45c2, uuid:b08238c5-d377-495a-9e29-44b857f971be, uuid:d387f119-9f80-4be8-a5b1-3220667dd62b, uuid:61f9df16-ef18-4b8a-bcbb-c93a3f919162
Manifest Reference Document ID  : uuid:e0822b0a-524b-4f6c-94f9-0e87da08c759, uuid:5c731104-1e02-4319-984d-465efe40ae5e, uuid:9706dfe4-6f04-43b2-85de-f158ffdef9ec, uuid:bed2a038-c529-45b9-beef-407b92721087, uuid:cdf1eb72-6beb-4502-8355-a83ce90e40bb, uuid:501a15ec-f503-41df-904c-8f97ae4468db, uuid:23014895-d9d2-4977-b942-0f07dd3393b7, uuid:f7d0b042-490a-46f4-be24-6f6592a99a82, uuid:f7d0b042-490a-46f4-be24-6f6592a99a82, uuid:cdf1eb72-6beb-4502-8355-a83ce90e40bb, uuid:00a1bfa7-b2c4-44e5-8d34-20926d8bb97e, uuid:4e4c567d-1867-4939-b094-accf62aba665, uuid:1bed6359-6359-4075-a103-d50bfde05b25, uuid:1359deb8-4d6a-498c-ab20-dff0749a802d, uuid:42f9061e-dd94-4aa6-be8c-03daf32a9b3b, uuid:58a9c23b-5cf9-479a-87f8-bd3c4fd99a76, uuid:3af090ce-a372-445e-8388-71f2355d4772, adobe:docid:photoshop:bdd41174-63da-11d7-87c4-849b1cdb6749, uuid:b18bf61e-ddca-4448-9261-8bf0c12d622c, uuid:4eaa0146-252f-4c53-b74a-9194922a5fee, uuid:472c7b72-eddd-4557-810d-3fee6d6d0404, uuid:07fcc53a-2bf8-4d59-b923-66efadb60d7a, uuid:ac83af6d-99ae-409c-b7bf-3a11f18cb86c, uuid:b99e6c4e-30b8-44d4-b742-ebe0d2fb97e2, uuid:b99e6c4e-30b8-44d4-b742-ebe0d2fb97e2, uuid:b99e6c4e-30b8-44d4-b742-ebe0d2fb97e2, uuid:a24e9a04-05cc-4fab-a2c9-2c54fdadc56c, uuid:79d885bb-7f30-43f4-95ca-f6c2d0d84f9b, uuid:2a07426e-eb54-4c19-9949-d5c025886dc8, uuid:71c2d5a5-827c-4b21-b887-da6c0620f8d7, uuid:58cca15b-aefa-408a-89a2-2604ec7bc26b, uuid:58cca15b-aefa-408a-89a2-2604ec7bc26b, uuid:58cca15b-aefa-408a-89a2-2604ec7bc26b, uuid:6bc471bf-13fe-4c66-a52c-83004cddab1c, uuid:895858bb-bccb-49b2-9196-6133341b2a9f, uuid:b5ec10bb-8b53-495b-a224-1712746094f2, uuid:73b557f5-1fc2-4775-ace6-49c51195fcb5, uuid:4e8ee594-1302-48a4-98cf-6e5cf1991ce9, uuid:bed2a038-c529-45b9-beef-407b92721087, uuid:e0822b0a-524b-4f6c-94f9-0e87da08c759, adobe:docid:photoshop:66064c66-646a-11d7-9b17-e1042c5691bf, adobe:docid:photoshop:d24f72c9-6474-11d7-9d35-bbbbeee7c888, uuid:bed2a038-c529-45b9-beef-407b92721087, uuid:bed2a038-c529-45b9-beef-407b92721087, uuid:cdf1eb72-6beb-4502-8355-a83ce90e40bb, uuid:bed2a038-c529-45b9-beef-407b92721087, uuid:bed2a038-c529-45b9-beef-407b92721087, adobe:docid:photoshop:e9187aeb-7547-11d9-928f-8a4b7ba0ef80, uuid:bed2a038-c529-45b9-beef-407b92721087, adobe:docid:photoshop:b1ce30c6-9eac-11d8-9537-84d8b668b1c6, adobe:docid:photoshop:c62ed03a-a88d-11d9-b086-b82372aac7b7, adobe:docid:photoshop:60993930-ba70-11d8-a24b-ee230997191b, adobe:docid:photoshop:11080979-c31b-11d9-a87d-d6cda2755a15, adobe:docid:photoshop:7f425012-c3d4-11d8-b748-9e36488c084e, adobe:docid:photoshop:746f4f9a-c31a-11d9-a87d-d6cda2755a15, adobe:docid:photoshop:67ab2bbb-7a00-11d9-9db1-899ddf725e4c, adobe:docid:photoshop:c4604809-a88d-11d9-b086-b82372aac7b7, adobe:docid:photoshop:65f0a333-a88d-11d9-b086-b82372aac7b7, adobe:docid:photoshop:21156e92-bcdc-11d9-9af2-f247f9d3322a, adobe:docid:photoshop:afff6f42-bdc0-11d9-94c7-c42c629ec111, adobe:docid:photoshop:c59afe69-a88d-11d9-b086-b82372aac7b7, adobe:docid:photoshop:27452706-80b7-11d7-aa6c-8aa8a21f9719, adobe:docid:photoshop:c4ecf2c3-a88d-11d9-b086-b82372aac7b7, adobe:docid:photoshop:c76e4b57-a88d-11d9-b086-b82372aac7b7, adobe:docid:photoshop:e0d57f9a-68a4-11d9-bbfe-f4cafaedb0a5, adobe:docid:photoshop:58dec527-68a4-11d9-bbfe-f4cafaedb0a5, adobe:docid:photoshop:b74cb3e8-be59-11d9-a4df-cf3786da8789, uuid:1710AFECFFDCDD118357CB8D8E1F9B48, adobe:docid:photoshop:afff6f42-bdc0-11d9-94c7-c42c629ec111, adobe:docid:photoshop:88312b92-aaa1-11d8-b439-e045639b9f62, adobe:docid:photoshop:f3ceed9c-e4e2-11d9-99a8-dc306820847b, adobe:docid:photoshop:c4ecf2c3-a88d-11d9-b086-b82372aac7b7, adobe:docid:photoshop:afff6f42-bdc0-11d9-94c7-c42c629ec111, adobe:docid:photoshop:4cf5ef2c-c32b-11d9-a87d-d6cda2755a15, adobe:docid:photoshop:1e8da50d-c32c-11d9-a87d-d6cda2755a15, uuid:f8f193fa-4611-4632-aafc-241f74cfc8f9, adobe:docid:photoshop:1e8da507-c32c-11d9-a87d-d6cda2755a15, adobe:docid:photoshop:f19eee70-89a1-11d8-ba66-d5db658352ef, adobe:docid:photoshop:aefcf378-bb4e-11d9-be12-b5c5fa77e95b, adobe:docid:photoshop:fa6a1151-7545-11d9-928f-8a4b7ba0ef80, adobe:docid:photoshop:aefcf378-bb4e-11d9-be12-b5c5fa77e95b, adobe:docid:photoshop:e580716b-52a8-11d9-a86c-df32811bbfd8, adobe:docid:photoshop:e9187aeb-7547-11d9-928f-8a4b7ba0ef80, adobe:docid:photoshop:b0f41bf6-7546-11d9-928f-8a4b7ba0ef80, adobe:docid:photoshop:4460feb4-7549-11d9-928f-8a4b7ba0ef80, adobe:docid:photoshop:7cd6d717-754d-11d9-928f-8a4b7ba0ef80, adobe:docid:photoshop:b0f41bf2-7546-11d9-928f-8a4b7ba0ef80, adobe:docid:photoshop:9a607441-754b-11d9-928f-8a4b7ba0ef80, adobe:docid:photoshop:5e56ee82-754d-11d9-928f-8a4b7ba0ef80, adobe:docid:photoshop:1d6a4fab-754a-11d9-928f-8a4b7ba0ef80, adobe:docid:photoshop:60b1f6ec-e26c-11d9-8a53-905c1f583d8d, adobe:docid:photoshop:d901d88b-addf-11d9-a639-b5fcc20c06d6, uuid:4c3aebfb-a38c-42db-b89e-4491ffa67f44, uuid:cdf1eb72-6beb-4502-8355-a83ce90e40bb, adobe:docid:photoshop:863d22fd-be44-11d9-a4df-cf3786da8789, adobe:docid:photoshop:c59afe72-a88d-11d9-b086-b82372aac7b7, adobe:docid:photoshop:5e56ee82-754d-11d9-928f-8a4b7ba0ef80, adobe:docid:photoshop:aefcf378-bb4e-11d9-be12-b5c5fa77e95b, adobe:docid:photoshop:fa6a1151-7545-11d9-928f-8a4b7ba0ef80, adobe:docid:photoshop:b0f41bf6-7546-11d9-928f-8a4b7ba0ef80, adobe:docid:photoshop:4460feb4-7549-11d9-928f-8a4b7ba0ef80, adobe:docid:photoshop:27ac1f83-a09a-11d9-ad90-f3e2cf3aad84, adobe:docid:photoshop:2088108c-754e-11d9-928f-8a4b7ba0ef80, adobe:docid:photoshop:b50cc614-d1e4-11d9-88d9-f706c20b34fa, adobe:docid:photoshop:e0f15671-e1b6-11d9-9060-83cbc1a69788, adobe:docid:photoshop:b0f41bf2-7546-11d9-928f-8a4b7ba0ef80, adobe:docid:photoshop:b1227a8d-c32e-11d9-a87d-d6cda2755a15, uuid:363d9ced-a731-45ad-ac8e-89f11b4a53ff, adobe:docid:photoshop:71479859-3eee-11d7-bef3-c5f27bc5c157, adobe:docid:photoshop:71479859-3eee-11d7-bef3-c5f27bc5c157, adobe:docid:photoshop:71479859-3eee-11d7-bef3-c5f27bc5c157, adobe:docid:photoshop:71479859-3eee-11d7-bef3-c5f27bc5c157, adobe:docid:photoshop:71479859-3eee-11d7-bef3-c5f27bc5c157, adobe:docid:photoshop:71479859-3eee-11d7-bef3-c5f27bc5c157, adobe:docid:photoshop:71479859-3eee-11d7-bef3-c5f27bc5c157, uuid:f9255cfc-a979-489a-a154-293d979cf49f, uuid:53762ce0-e850-48b0-8755-2bbb9d4c2535, uuid:9533f33f-8c30-46c3-821d-42fb267a9219, uuid:b4b7410a-a0ce-4ec8-b1c5-a0664ea3122c, uuid:96d2eb3a-6fc0-432d-bd3b-71c87057afe8, uuid:8bb54cbb-e382-4902-aba7-4ee1ee352878, uuid:aca31dec-a931-4498-b216-2fa9a34bf7b6, uuid:59e57e7e-9ab8-40e5-b629-3ed6c717a3f5, uuid:b56b908c-453e-4509-abfd-dcba983aeb1e, adobe:docid:photoshop:71479859-3eee-11d7-bef3-c5f27bc5c157, adobe:docid:photoshop:71479859-3eee-11d7-bef3-c5f27bc5c157, adobe:docid:photoshop:71479859-3eee-11d7-bef3-c5f27bc5c157, adobe:docid:photoshop:27e7348a-702a-11d7-b9e8-ef9b06869058, adobe:docid:photoshop:27e7348a-702a-11d7-b9e8-ef9b06869058, uuid:feac5585-0b16-4889-93a4-ddc511873abe, uuid:b4c83e91-3304-4316-8460-ed50f1147477, uuid:e7be8948-3de0-4bce-9a2b-7a40cda2f3d8, adobe:docid:photoshop:27e7348a-702a-11d7-b9e8-ef9b06869058, uuid:feac5585-0b16-4889-93a4-ddc511873abe, adobe:docid:photoshop:b791da5b-a5fc-11d9-b021-ba9b9e81e51c, adobe:docid:photoshop:b791da5b-a5fc-11d9-b021-ba9b9e81e51c, uuid:5ff3fad0-d0fd-4a91-94e3-d6dec3e6723c, uuid:66e4e8a3-484b-4c92-bd1b-08f90e0ef915, uuid:6bbded27-0a07-4093-99b3-0dfc1f75e9cf
Format                          : application/pdf
Producer                        : Adobe PDF Library 8.0
Trapped                         : False
Page Count                      : 124
Creator                         : Adobe InDesign CS3 (5.0.3)

EXIF Metadata provided by EXIF.tools

Mitsubishi Digital Electronics Projection Television WD 73727

Mitsubishi Digital Electronics Projection Television WD-52628 WD-52628

Navigation menu

Versions of this User Manual:

Views

Navigation