X7G NAGA6 Sceptre Naga VI LCD User’s Manual
User Manual: Sceptre X7G-Naga VI LCD User’s Manual Troubleshoot Sceptre X7G-Naga VI LCD |
Open the PDF directly: View PDF 
.
Page Count: 23
| Download | |
| Open PDF In Browser | View PDF |
FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. FCC WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful inerference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. • Connect the equipment into an outlet different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: To comply with the limits for an FCC Class B computing device, always use the shielded signal cord supplied with this unit. i The Federal Communications Commission warns that changes or modifications of the unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CE mark for Class B ITE (Following European standard EN55022/1998; EN610003-2/1995; EN61000-3-3/1995, EN55024/1998, EN60950-1/2001) Radio Frequency Interference Statement Warning: This is a Class B product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures. Canadian Doc Notice For Class B Computing Devices This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications. “Le présent appareil numérique n’èmet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class B prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada." ii TABLE OF CONTENTS TABLE OF CONTENTS...........................................................................................III Your New LCD Monitor 1 Unpacking 1 Product feature 2 Identifying Components 3 Adjusting the Tilting Angle 5 Connecting AC Power and Video Cable 6 Power Management System 6 The LCD Monitor's Control Panel 7 Adjusting the Monitor’s Display 8 TFT LCD Monitor Specifications 14 Supported Timing 17 Troubleshooting 17 iii The LCD Monitor Your New LCD Monitor Your LCD Monitor has been designed to be versatile, ergonomic and user-friendly. The LCD Monitor is capable of displaying most standards, from 640x400 VGA to 1280x1024 SXGA. The digital controls located on the front panel allow the user to easily adjust the Monitor’s display parameters, and the LCD Monitor’s small footprint gives you more room in your workspace for other peripherals. Lightweight and compact, the LCD Monitor is the perfect solution for users on the go. You can use the LCD Monitor for everything from making business presentations to playing computer games. The architecture of the LCD Monitor incorporates an LCD panel that produces a clear display with low radiation emission. And with its low power consumption, the LCD Monitor helps you reduce your power bill. Unpacking Before unpacking your LCD Monitor, prepare a suitable workspace for your LCD Monitor and computer. Look for a stable, level and clean surface near a wall outlet. Even though the LCD Monitor uses very little power, you should put it in a location, which allows sufficient airflow to ensure that the LCD Monitor and your computer do not overheat. Set up your LCD Monitor so that the panel is not facing a window where sunlight often comes in. The glare caused by sunlight reflecting off of the LCD Monitor’s screen will make it difficult to use the Monitor for viewing. Note: Using a computer for an extended period of time with a poor workstation set-up and incorrect working habits can cause health problems. The science of ergonomics studies the relationship between health and a suitable working environment. There is a section on ergonomics at the end of this chapter. For more information on ergonomics, contact your nearest computer bookstore, or local library. The Internet also has information on this and other subjects. 1 Rev.1 After unpacking your LCD monitor, make sure the following items are included in the box and are in good condition: • LCD monitor • Power Cord • Monitor-To-PC Analog signal cable 15pin, which has been attached with monitor • User’s manual If you find that any item to be missing or appear to be damaged, contact your dealer immediately. Do not throw away the packing material or shipping carton in case you need to ship or store the LCD monitor in the future. Product feature 500:1 high contrast ratio 1280 X 1024 native resolution VESA 100 mm wall mount compliance using M3 screws at 8 mm length . 2 Identifying Components A. The LCD Monitor — Front View 3 1 4 2 Figure 1-1: The LCD Monitor Front View 1. Power-On Indicator The LED indicator lit blue when the power is on and red when the LCD monitor is in power-saving mode. 2. Monitor Stand 3. LCD Screen The LCD monitor screen is a 17-inch TFT 1280 x 1024 screen. 4. LCD Monitor Control Panel Refer to Chapter 2 for more details. 3 Rev.1 B. "Hot Keys" for Quick Adjustment of Monitor Settings + Figure 1-2: "Hot Keys" Brightness 1. Brightness Adjustment "hot key": Press the “+” button to allow you to adjust the brightness of the LCD Monitor directly 50 2. Contrast Adjustment “ Hot key” Contrast Press the “-“ button to allow you to adjust the contrast of the LCD Monitor directly 50 3. Auto adjustment “ Hot Key “ Press this to allow you to do the auto adjustment to get the optimized view 4 Auto Adjusting the Tilting Angle The LCD Monitor’s angle settings range from 0°° to 90 0° Figure 1-3: Tilting the Monitor 5 Rev.1 Connecting AC Power and Video Cable Note: Turn off your PC and the LCD monitor before connecting your LCD monitor to the computer. Figure 1-4: The AC Adapter Power Management System This LCD Monitor complies with the VESA DPMS power management proposal. When the LCD Monitor is in power-saving mode or detected an incorrect signal timing, the monitor screen will be blank and the power LED indicator from blue light change to red light. 6 The Display Controls The LCD Monitor’s Control Panel + Figure 2-1: The Control Panel 1. : Enable the OSD Menu button or / Move the cursor to the left ( when OSD is enabled) 2. : Move the cursor to the Right ( When OSD is enabled) / Auto-adjustment hot key 3. - : Enter into the sub-menu or decrease the value / Contrast hot key 4. + : Enter into the sub-menu or increase the value / Brightenss hot key 5. :Power Switch This button lets you turn power for the LCD monitor ON or OFF. When OSD menu is on the screen, it could turn off the OSD menu. 7 Rev.1 Adjusting the Monitor’s Display OSD Main Menu 1. Pressing the button causes the screen below to appear. 2. Use the & key to select the desired group, then press – or + key to enter into sub-menu 3. Repeat step 2 to select the changed item, then – or + to change the value. Main Menu Sub Menu Description Monitor Control OSD Main SCREEN 8 MONITOR-CONTROL Allow you to adjust the LCD monitor’s display settings. Press the Adjustment control button to display the submenu. Use the Function Select button to select one of the following submenu options: Auto Adjustment Press the Adjustment control button to let the monitor determine and select the setting that is most appropriate for your system requirements. H-POSITION: To move the LCD monitor's display left or right on a horizontal plane. V- POSITION: To move the LCD monitor's display up or down on a vertical plane. PHASE:) To adjust the focus and clarity of the display CLOCK: To adjust the display pixel alignment. 9 Rev.1 RESET: To reset all of the Monitor-Control submenu settings to the factory default. GRAPHIC/TEXT: Press the adjustment control button to switch between text and graphic display modes. EXIT: To exits the Monitor-Control submenu OSD-CONTROL The OSD-Control menu lets you adjust the position of the OSD on the screen. Press the Adjustment control button to display the submenu. OSD-H-POSITION: To change the position of the OSD on a horizontal plane OSD-V-POSITION: To change the position of the OSD on a vertical plane. OSD-TIMER: The OSD menu display time can be set at 5, 10, 15, 20, 25 or 30 seconds. EXIT: To exit the OSD-Control submenu. GRAPHIC-CONTROL: The Graphic-Control option lets you make adjustments that effect the contrast,brightness and color of the LCD monitor’s display. 10 CONTRAST: To adjust the contrast level of the display screen BRIGHTNESS: To adjust the light level on the display screen. COLOR: To select the LCD monitor’s color display. The available options are cold, warm and User. Selecting the user option lets you make individual adjustments to the R, G and B colors. COLOR R, G and B ADJUST: To make individual adjustments to the Red, Blue, Green (RGB) gain for the color temperature. AUTO LEVEL: To automatically adjust the display white balance. You have to set display in full white mode before actrive the color auto Adjusting. RESET: 11 Rev.1 To reset all of the Graphic-Control submenu settings to the factory default. EXIT: To exit the Graphic-Control submenu. MISC-CONTROL: The Misc-Control menu option lets you select the OSD display language and view system information. LANGUAGE: The supported languages include German, English, French, Spanish, Italian,Japanese . SHARPNESS: To adjust the sharpness level of the display. INFORMATION: To indicate display mode timings and firmware version. EXIT: To exit the Misc-Control submenu. EXIT: Use the OSD Exit item to close the OSD menu. The OSD will disappear by itself if left inactive. 12 13 Rev.1 Note: 1) No video N O V IDEO When the monitor is ON and there is no video signal received, the following message will be displayed 2) Signal out of range When the frequency range of the signal is out of the monitor specifications, the display will show the following message O VER R ANGE 14 Appendix A TFT LCD Monitor Specifications LCD Panel 17" SXGA Control Functions Power On-Screen Display (OSD) Software Power switch with LED indicator (ON/OFF) Main Menu MONITORCONTROL OSD-CONTROL MISC-CONTROL GRAPHICCONTROL Submenu Auto Adjustment, H-POSITION, V- POSITION, PHASE, CLOCK, GRAPHIC/TEXT, RESET, EXIT OSD-H-POSITION, OSD-VPOSITION, OSD-TIMER, EXIT LANGUAGE,SHARPNESS, INFORMATION, EXIT CONTRAST, BRIGHTNESS, COLOR, COLOR R, G and B ADJUST, AUTO LEVEL, RESET, EXIT EXIT Display Area (mm) 338 X 270 (17" diagonal) Display Colors Video Interface Plug and Play 16.2 M VGA Compatible Analog RGB (15-pin mini D-Sub) DDC1 and DDC2B 15 Rev.1 Scanning Frequency H / V, Hz 30-81K 50-75 Power Management VESA DPMS Power Consumption (ON / OFF) 35W / 1W Max. Dimensions WXHXD 17.32 X 19.57 X 4.33 (inch) 440 X 497 X 110.00 (mm) Net Weight (approx.) 9.39 lbs (4.27Kg) Power Supply (100–240 V AC, 50/60 Hz) Environment Operation tmperature : 0 to 35°C, humidity: 10–90% Storage tmperature : -20 to +60 °C, humidity: 8–95% Regulatory CCC,UL,CUL,FCC ,CE,CB 16 Appendix B Supported Timing Item Mode Resolution 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 VGA VGA MAC VESA VESA VGA VESA VESA VESA MAC VESA VESA VESA VESA MAC VESA VESA 640x350 640x480 640x480 640x480 640x480 720x400 800x600 800x600 800x600 832x624 1024x768 1024x768 1024x768 1152x864 1152x870 1280x1024 1280x1024 (MHz) Dot Clock (MHz) 25.17 25.18 30.24 31.50 31.50 28.32 40.00 50.00 49.50 57.29 65.00 75.00 78.75 108 100 108 135 Vertical Scanning Frequency (Hz) 70.08 60.00 67.00 72.80 75.00 70.08 60.32 72.19 75.00 74.55 60.00 70.10 75.00 75.00 75.06 60.00 75.00 Horizontal Scanning Frequency (kHz) 31.47 31.47 35.00 37.86 37.5 31.47 37.88 48.08 46.86 49.72 48.36 56.48 60.02 67.50 68.68 64.00 80.00 *Once a mode is optimized, there is no need to make any further adjustment as long as the VGA card remains unchanged. *Specifications are subject to change without notice. 17 Rev.1 Appendix C Troubleshooting This LCD monitor comes pre-adjusted with standard VGA timing. Due to output timing differences among various video adapters, you may initially experience an unstable or unclear display when a new display mode or new VGA card is selected. Before applying any of the following troubleshooting procedures, you should first apply the Auto Adjust option in the OSD menu. PROBLEM: Display is unclear and unstable To stabilize and clarify your display, press and release the auto adjust button the monitor will do auto adjut for you to get best image. Please be noticed that the 1280X1024 resolution mode will give you the optimal sharpness display. PROBLEM: There is no video on screen If there is no display on the LCD, refer to the following: 1. Make sure that the power indicator on the LCD monitor is lit, that all connections are secure, and that the system is running on the correct timing. Refer to Appendix B for information on timing. 2. Turn off the LCD monitor and then turn it back on again. Press the OSD Menu button (refer to Chapter 2) once and then press one of the Adjustment Control buttons several times. If there is still no display, press the other Adjustment Control button several times. 3. If step 2 does not work, connect your PC system to another external CRT. If your PC system functions properly with a CRT monitor but it does not function with the LCD monitor, and the LCD monitor’s power LED is red, the output timing of the PC’s VGA card may be out of the LCD’s synchronous range. Change 18 to one of the alternate modes listed in Appendix B, or replace the video adapter and repeat steps 1 and 2. 4. If the power LED is not lit, check that the AC power connector is securely connected, If the power LED is still not lit, please contact your dealer for assistance. PROBLEM: The LCD displays “over range” error message 1. If you have a CRT monitor, please connect the CRT monitor to the computer and change the refresh rate down to 60hz via your video card’s display settings menu. After the setting of 60hz has been change you can then use the LCD on the computer. 2. If you do NOT have a CRT monitor, please make sure both the X7G-NagaVI and your computer is turned off. Afterwards turn on the LCD and the computer. 3. While the computer is turned on, press the “F8” key on your keyboard continuously until a selection menu appears and select the “Safe Mode” option, for windows XP please select “VGA mode”. 4. When you’ve entered Safe Mode please uninstall any video card driver and monitor driver by using either the “Add / Remove Programs” icon or going into “System Properties” and manually removing anything under “Monitors” and “Display Adapters”. 5. After removing all the drivers, please reboot your computer and you should be able to see windows. Please then procede to install your monitor driver first, then your video card driver. Please remember to make sure your refresh rate should be at 60hz. 19 Rev.1
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 23 Producer : PrimoPDF Create Date : 2008:10:03 22:59:14 Modify Date : 2008:10:03 22:59:14 Title : Microsoft Word - X7G-NAGA6.doc Creator : PrimoPDF http://www.primopdf.com Author : steven-lEXIF Metadata provided by EXIF.tools