Zip In Line Brochure
User Manual: Zip InLine Brochure
Open the PDF directly: View PDF 
.
Page Count: 36
| Download | |
| Open PDF In Browser | View PDF |
Ne w Ra ng e 2011/2012 Zip InLine Electronically controlled instantaneous water heaters The most energy efficient way to directly heat water electrically s Zip InLine electronically controlled instantaneous water heaters At a glance Pages Why Zip Instantaneous? 4-5 The Inside Story 6-7 In Good Company 8-9 Selection Charts 10-11 ES—Handwashing 12-15 NEW ES installation packs, heater, tap and fittings 16-17 ILX—Handwashing, Sinks & Showers 18-21 NEW CEX—Handwashing, Sinks & Showers 22-25 NEW DEX/DBX—Handwashing, Sinks, Showers & Baths 26-29 InLine Accessories 30-31 Performance Charts 32-33 Application & Accessories Guide 34-35 3 Why Zip instantaneous water heating? Zip InLine instantaneous water heaters are the most energy efficient means of directly heating water electrically. Using the very latest German technology, Zip InLine offers a host of Specifier, Installer and End User benefits. G 4 Unrivalled energy efficiency - No standing heat loss G Fast heat up times G Sophisticated electronic control G Unlimited hot water supply G Easy to install G Neat, compact design -23 Energy comparison: % Energy Efficiency Zip InLine saves energy by: 1. Heating only the water drawn off 2. Avoiding stored water heat losses When comparing the energy used over 24 hours to deliver 75 litres of hot water at 38ºC (assuming 12ºC supply) typical savings of 23% can be achieved: Stored hot water Instantaneous hot water Product Energy Usage 15 litre storage water heater 3.0 kWh Zip InLine Instantaneous 2.3 kWh Percentage savings may be less with increased demand but significantly more during periods without draw off. Water Conservation Zip InLine is designed for installation close to the point of use, requiring little run off of water before achieving temperature. Savings per draw off compared to centralised systems with long pipe runs are as follows: Traditional System Pipe Run Litres saved per draw off 10 metres 3.2 5 The inside story Easy installation Smart design Zip InLine products simply connect to standard closed outlet taps without the need for unvented water controls. ES and DEX/DBX are supplied with bracket for easy fitting. The units’ compact size enables them to fit neatly and unobtrusively in any location. All products are designed to be positioned as close to the outlet fitting as possible, thus minimising the thermal losses. In this way additional energy saving can be made. Power to the heating element is regulated to ensure that the required outlet temperature is achieved precisely* regardless of the incoming water temperature and pressure. The ES range features a choice of installation methods, either using standard tapware and fittings or, alternatively, one of two kit options. These offer either a non-concussive tap or mixer tap, see pages 16-17 for full details. Unlimited supply of hot water Advanced electronic control Zip InLine delivers a continuous supply of hot water at the selected temperature*. *Subject to sufficient power being available to achieve the required temperature and flow rate. 6 Innovation Zip continue to lead the way in hot water technology with new additions to the InLine range of instantaneous water heaters. All newly introduced InLine products feature Bare Wire technology bringing all the benefits of control, comfort and efficiency, that have been enjoyed for many years on the continent, to users in the UK. Zip InLine ES, CEX, DEX and DBX ranges all benefit from the advantages of Bare Wire technology. Cut-away showing the bare wire element in the water flow path Bare wire technology Unlike traditional instantaneous water heating products where the heating element is enclosed in a heat exchanger, bare wire products see the heating element directly immersed in the water flow path. This allows heat to be transmitted directly to the water, giving significantly greater efficiency and a much quicker heat up time, typically less than 2 seconds. The mass of traditional elements and heat exchangers absorbs a significant amount of energy before water is delivered at a usable temperature. This energy is allowed to dissipate after use or can cause temperature spikes when more water is drawn off. Bare wire technology prevents these issues from occurring providing the most energy efficient means of heating water electrically. The quick reaction time of bare wire technology, coupled with Zip InLine electronic control systems that only apply exactly the power necessary to achieve the required temperature, ensure accurate temperature control with the most efficient use of energy. Meticulous design in accordance with industry standards for bare wire technology ensures complete protection as attested by VDE approval to the appropriate safety directives. 7 In good company Among many thousands of Zip InLine installations, we feature some key applications where significant benefits have been achieved. Northern General Hospital, Sheffield Laurence Fowles, Senior Project Manager of Sheffield Foundation NHS Trust says “We installed 10 Zip ES4 InLine instantaneous point of use water heaters into the GP Collaborative department at Northern General Hospital, to reduce standing losses. The building is a standalone unit which had two large hot water storage calorifiers within its self contained plantroom. We eliminated the need for hot water storage, thus reducing standing losses and pressure vessel insurance inspections. The ES units proved so successful that we have installed several more 8 around the Trust because of the aforementioned reasons and to reduce the risk of legionella which is associated with conventional water heating methods. We are currently embarking upon a project to install a further 20 more units into the Ultrasound/CT/MRI department at the Northern General Hospital which allows us to isolate an exceptionally long length of hot water flow and return pipework, enabling the estates department to make considerable energy savings.” Isis School of English, Greenwich, London Ian McAdam of Contractors Stewart Anthony, when faced with the problem of designing and building a hot water solution for the Isis School of English in Greenwich, London, decided to turn to Zip Heaters for support. “I was anxious to provide a solution for Isis that had no messy and inefficient pipework running throughout the building. We decided to use a combination of Zip InLine instantaneous ES 6kW and ILX 9kW units, at the point of use, to provide hot water to the kitchens, toilets, together with the disabled area and toilets. The client is very happy with the solution and we will use the same combination in Phase 2.” Pura Design Ltd. Hythe Kent “We have recently completed a project in Berkeley Square, Mayfair, where the tenants of an 8 storey office building were reporting low hot water temperature and very low flow rates. The central hot water generating plant consisted of two indirect water heaters fed from gas boilers in a basement plantroom with the hot water being distributed around the building using flow and return pipework with secondary circulation pumps. The decision was taken to strip out the existing central hot water generating plant and install local electric water heaters at point of use. Throughout the building there were several single handbasins. These were fitted with Zip InLine ES instantaneous water heaters which are small enough to be surface mounted without being obtrusive and required minimum pipework.” 9 Zip InLine selection chart With indicative flow rate at rated voltages – single phase Product Type Application ES ILX CEX ES3 ES4 ES6 ILX006 ILX009 CEX 3.1kW 4.8kW 6.0kW 7.2kW 9.6kW 7.2kW 9.6kW Handwash 38°C Kitchen sink 50°C Shower 38°C Bath 38°C 10 Zip InLine selection chart With indicative flow rate at rated voltages – three phase Product Type Application ILX DEX DBX ILX012 DEX DEX DEX DEX DBX18 DBX21 DBX24 DBX27 13.5kW 18kW 21kW 24kW 27kW 18kW 21kW 24kW 27kW Handwash 38°C Kitchen sink 50°C Shower 38°C Bath 38°C Always consider the total combined flow rate of all outlets when selecting the appropriate InLine product. See pages 34 & 35 for more details. 11 12 Zip InLine ES Instantaneous water heater for handwashing Features and benefits G Flow rate of 1.7 – 3.3 litres/minute* G Choice of 3.1, 4.8 and 6.0 kW ratings# G Unlimited hot water supply for handwashing G Bare wire technology for fast heat up G Smart, compact design G Intended for use with taps having removable M22/M24 nozzles G Heats up only the water drawn off – no standing heat loss G Sophisticated electronics adjusts power applied to compensate for inlet pressure and temperature variations * Delivering 38°C at 240V and 12°C supply temperature. # At 240V. 13 Zip InLine ES Instantaneous water heater for handwashing Plumbing The appliance is intended for connection to the mains water supply. It should be installed by a suitably qualified person. It may be used as an unvented installation, as shown in the diagram below, or as a vented installation as described in the fitting instructions. For correct operation it is essential that the special tap nozzle supplied is fitted to the tap spout. Intended for use with taps having removable M22/M24 nozzles Not recommended for use with thermostatic mixing valves or taps. Electrical Description • The most energy efficient way to directly heat water electrically • Zip InLine ES provides instant hot water for handwashing • Heating power is controlled electronically to maintain set temperature • Sophisticated electronics adjusts power applied to compensate for inlet pressure and temperature variations The appliance must be earthed and connected to the mains supply by means of permanent wiring through suitable isolation, having a contact separation of 3mm in all poles and should only be operated if protected by an RCD rated at 30mA. Installation must be in accordance with current IEE regulations. Typical Installation • Outlet temperature factory set to 38°C, but can be installer adjusted between 30°C and 50°C • Stainless steel bare wire heating element for fast heat up Flow control valve Mains supply • Double pole over-temperature protection Service valve 132mm • Intended for use with taps having removable M22/M24 nozzles 187mm Location The appliance must be installed in a frost-free environment. Zip ES products comply with IP24 and may be installed in Zone 1. The unit should be positioned as close as possible to the outlet to minimise heat loss. Approvals WRAS and VDE approved, CE endorsed Warranty 12 months on-site parts and labour 14 Zip Technical Support 0845 602 4533 Zip InLine ES Technical Data Model ES3 ES4 Pressure rating ES6 10 bar Element type Bare wire Supply voltage (V) 240 Nominal power rating @ 240V (kW) 3.1 4.8 6.0 Nominal current @ 240V (A) 13 20 25 Temperature adjustment (installer) 30°C - 50°C Maximum inlet temperature 30°C Factory set temperature 38°C Factory set Flow rate @ 38°C (litres/min) 1.7 Application guide lines 2.6 3.3 See pages 34-35 Maximum temperature increase @ 240V and a flow rate of: 2.0 litres/min 22°C 34°C 43°C 2.5 litres/min 18°C 27°C 34°C 3.0 litres/min 15°C 23°C 29°C 3.5 litres/min 13°C 20°C 24°C 4.0 litres/min 11°C 17°C 21°C Switch on flow rate (litres/min) 1.2 1.5 1.5 Switch off flow rate (litres/min) 1.0 1.3 1.3 >1300 ohm.cm >1000 ohm.cm >1000 ohm.cm Required specific water resistance @ 15°C Capacity (litres) 0.2 Filled weight (kg) 1.5 1/ 2 Water connections Dimensions H x W x D (mm) ” BSP 132 x 187 x 80 Protection class (IEC 529) IP24 Zip Service/Maintenance Support 0800 077 8302 15 Zip InLine ES Instantaneous handwash packs complete with tap and fittings Features and benefits G G G G Comprehensive kits for ease of plumbing: ES instantaneous water heater, compatible tap and all necessary local pipe work and fittings. A choice of 3 power ratings and 2 tap designs. All components WRAS approved. Non-concussive tap (NC) Pack: G G G G ES Instantaneous water heater Non-concussive single outlet tap 50 cm braided hose for connection to heater 50 cm braided hose for connection to tap (Isolating valve NOT supplied) Non-concussive tap Matching cold tap Mixer tap (MT) Pack: G G G G G G 16 ES Instantaneous water heater Single lever mixer tap complete with braided hoses for connection to tap 50 cm braided hose for connection to heater Non return valve for hot supply to tap Flow rate adjuster for cold supply to tap T piece connector (Isolating valve NOT supplied) Single lever mixer tap Non Concussive (NC) Pack Product Code ES3/NC ES4/NC ES6/NC ES3/MT ES4/MT ES6/MT ZL018 Tap Type Mixer Tap (MT) Pack Rating kW @ 240V Non-concussive 3.1 Non-concussive 4.8 Non-concussive 6.0 Single lever mixer 3.1 Single lever mixer 4.8 Single lever mixer 6.0 Matching non-concussive cold tap *At 240V and 12°C supply temperature. *38°C Max Flow rate ltrs/min 1.7 2.6 3.3 1.7 2.6 3.3 17 18 Zip InLine ILX Instantaneous water heaters for hand washing, sinks and showers Features and benefits G G G Flow Rate of 4.0 – 6.0 litres/minute Choice of 7.2kW,* 9.6kW* single phase and 13.5kW three phase ratings Provides a constant supply of hot water for a range of applications G Tubular elements – 7.2kW and 9.6kW G Bare wire element – 13.5kW G User adjustable temperature control G Heater ‘ON’, ‘Low Flow’ and ‘Over Heat’ Indicators G Heats only the water drawn off – no standing heat loss G Electronic Power control adjusts to compensate for inlet pressure and temperature variations *At 240V 19 Zip InLine ILX Instantaneous water heater for handwashing, sinks and showers Description Electrical • The ILX range provides energy efficient hot water for a wide range of applications The heater must be earthed and connected to the mains supply by means of permanent wiring through suitable isolation, having a contact separation of 3mm in all poles and should only be operated if protected by an RCD rated at 30mA. • Heating power is controlled electronically to maintain set temperature • User adjustable temperature from 35°C to 55°C • Element types: ILX006 & ILX009 – tubular ILX012 – bare wire • Double pole over-temperature protection • Electronic Power control to compensate for inlet pressure and temperature variations ILX012 requires three phase electrical supply. Installation must be in accordance with current IEE regulations. Typical installation • Automatic power reduction to avoid excessive temperatures with visual indication Location The heater must be installed in a frost-free environment. The unit should be located as close as possible to the outlet to minimise heat loss (recommended maximum 2 mtrs). Plumbing The heater is intended for connection to the mains water supply. It should be installed by a suitably qualified person. Approvals The unit is intended to be used as an unvented installation, as shown in the diagram opposite. VDE approved, CE endorsed. For optimum flow characteristics use with Zip tap spray or aerator nozzles and handsets. (See page 31 and ‘Applications guides’ on Pages 34/35). 12 months on-site parts and labour. Warranty Zip Technical Support 0845 602 4533 20 Zip InLine ILX Technical Data Model ILX006 Pressure rating ILX012 6 bar 10 bar Tubular Bare wire 240 - single phase 400 - three phase Element type Supply voltage (V) ILX009 Nominal power rating @ supply voltage (kW) 7.2 9.6 13.5 Nominal current @ supply voltage (A) 30 40 19.5 User Temperature Adjustment 35°C - 55°C Maximum inlet temperature 30°C Factory set flow rate at 3 bar (litres/min) 3.5 Application guide lines 4.5 5.0 See pages 34/35 Maximum temperature increase at rated power and a flow rate of: 3.0 litres/min 34°C 46°C 55°C 4.0 litres/min 26°C 34°C 48°C 5.0 litres/min 21°C 27°C 38°C 6.0 litres/min 17°C 23°C 32°C Switch on flow rate (litres/min) 2.0 Switch off flow rate (litres/min) 1.8 Required specific water resistance @ 15°C >1100 ohm.cm (ILX012 only) Capacity (litres) 0.2 Filled weight (kg) 2.2 1/ 2 Water connections Dimensions H x W x D (mm) ” BSP 330 x 210 x 90 Protection class (IEC 529) IP25 Zip Service/Maintenance Support 0800 077 8302 21 22 Zip InLine CEX Instantaneous water heaters for handwashing, sinks and showers Features and benefits G Flow rate up to 5 litres/minute* to supply one or more outlets G Power rating can be set on installation to 7.2kW# or 9.6kW# G Available for installation over-sink (CEX-O) or under-sink (CEX-U) G Bare wire elements for fast heat-up G Zero standing heat loss G Provides a constant supply of hot water G G G Heating power electronically adjusted to compensate for variable inlet pressure and temperature Suitable for use with pre-heated water from solar heating systems Outlet temperature user adjustable between 30°C and 55°C with two programmable settings *At 6 bar water pressure # At 240V 23 Zip InLine CEX Instantaneous water heaters for handwashing, sinks and showers Description Plumbing CEX • Provides a constant supply of hot water to one or more outlets • Regulates power consumption electronically depending on supply water temperature and flow rate to achieve the required outlet temperature • Power rating can be selected at the time of installation • Bare wire heating element ensures fast heat up times • Required outlet temperature can be set via two touch sensitive keys between 30°C to 55°C with digital display • Enables selection of two pre-programmed temperature settings • Visible indicator of when heating power available is unable to achieve required temperature at the selected flow rate The appliance is intended for connection to a potable mains water supply. Hot and cold connecting pipes should be WRAS approved and of copper or steel construction. Minimum flow rate of 2.0 litres/min. Should be installed by a suitably qualified person. Electrical The heater must be earthed and connected to the mains supply through an isolation switch having contact separation of at least 3mm in all poles and protected by a suitably rated circuit breaker. The connection cable must be in accordance with the power rating of the appliance and the specific requirements of the site. Installation must be in accordance with current IEE regulations. Typical installation • Suitable for use with pre-heated water from solar heating systems • Optional wireless control (Code –ZL016) Location The heater must be installed in a frost free environment. It should be located as close as possible to the outlet to minimise heat loss (recommended maximum 2 metres). Complies with IP25 for oversink and IP24 for undersink and may be installed in Zone 1. Approvals WRAS, VDE, CE endorsed. Warranty 12 months on-site parts and labour. 24 Zip Technical Support 0845 602 4533 Zip InLine CEX Technical Data Model Application CEX-O CEX-U Over-sink Under-sink Power rating 7.2kW / 9.6kW(1) Rated current 30A (7.2kW) / 40A (9.6kW) Power supply 1/N/PE ~240V AC Hot water (l/min) Maximum at Δt = 25°C 4.1 (7.2kW) / 5.0(2) (9.6kW) Rated volume (litres) 0.3 Rated pressure 1 MPa (10 bar) Element type Bare wire heating system IES >1100 Ωcm @ 15°C Required specific water resistance Maximum inlet temperature 70°C Switch on flow rate (l/min) 2.0 Maximum flow rate (l/min) 5.0(2) Pressure loss @ 2.5 l/min @ 9.0 l/min 0.2 ba 1.3 bar(3) Temperature setting range 30°C – 55°C Maximum weight (kg) 2.70 Dimensions H x W x D (mm) 294 x 177 x 108 Water connections Protection class ½” BSP IP25 IP24 (1) Power rating selected at time of installation (2) Flow rate limited to achieve optimum temperature rise (3) Without flow regulator Zip Service/Maintenance Support 0800 077 8302 25 26 Zip InLine DEX / DBX Instantaneous water heaters for handwashing, sinks, showers and baths Features and benefits G G G Generates large volumes of hot water for a variety of applications DBX available in a choice of 18, 21, 24 & 27kW three phase ratings DEX ratings are installer adjustable from 18 to 27kW G Bare wire elements for fast heat up G Zero standing heat loss G Provides a constant supply of hot water G G G DEX DBX Heating power electronically adjusted to compensate for variable inlet pressure and temperature DEX suitable for use with pre-heated water from solar heating systems DEX enables outlet temperature to be selected between 20°C and 60°C with two programmable settings 27 Zip InLine DEX / DBX Instantaneous water heaters for handwashing, sinks, showers and baths Description Plumbing DEX / DBX • Provide a constant supply of hot water to one or more outlets • Regulate power consumption electronically depending on supply temperature, pressure and flow rate to maintain set temperature The appliance is intended for connection to a potable mains water supply. Hot and cold connecting pipes should be WRAS approved and of copper or steel construction. Minimum flow rate of 2.5 litres/min. Should be installed by a suitably qualified person. Electrical DBX The heater must be earthed and connected to the mains supply through an isolation switch having contact separation of at least 3mm in all poles and protected by a suitably rated RCD. Requires three phase supply. Installation must be in accordance with current IEE regulations. • Outlet temperature factory set to 50°C, installer adjustable from 30 to 60°C Typical installation • Bare wire heating systems for fast response and energy efficient delivery of hot water DEX • Power rating can be installer adjustable from 18 to 27kW • Required outlet temperature can be set with touch sensitive keys within the range 20 - 60°C • Choice of two programmable temperature settings • Suitable for use with pre-heated water from solar heating systems up to a maximum of 70°C Location The heater must be installed in a frost free environment. It should be located as close as possible to the outlet to minimise heat loss (recommended maximum 2 metres). Complies with IP25 and may be installed in Zone 1. Approvals WRAS, VDE, CE endorsed. Warranty 12 months on-site parts and labour. Zip Technical Support 0845 602 4533 28 Zip InLine DEX / DBX Technical Data DEX Model DBX 18 Rating (current) Power supply 18kW(26A) Hot water (l/min) Maximum @ t = 28K Maximum @ t = 38K Rated volume (litres) Rated pressure Element type Required specific water resistance DEX DBX Maximum inlet temperature DEX DBX Switch on flow rate (l/min) Maximum flow rate (l/min) DEX DBX Pressure loss @ 2.5 l/min @ 9.0 l/min Temperature setting range DEX DBX Maximum weight (kg) Dimensions H x W x D (mm) Water connections Protection class 9.2(2) 6.8 DBX 21 DBX 24 21kW(30A) 24 kW(35A) 3/PE 380—415V AC 10.7(2) 7.9 12.3(2) 9.0(2) DBX 27 27kW(39A) 3/PE 400V AC(1) 13.8(2) 10.2(2) 0.4 1 MPa (10 bar) Bare wire heating system >1100 Ωcm @ 15°C >1300 Ωcm @ 15°C 70°C 30°C 2.5 8.0(3) 7.0(3) 8.0(3) 8.0(3) 9.0(3) 0.2 bar 1.3 bar(4) 20°C – 60°C 30°C – 60°C 3.70 466 x 231 x 97 ½” BSP IP25 (1) Maximum 400V for DEX and DBX at 27kW (2) Mixed with cold water at the outlet (3) Flow rate limited to achieve optimum temperature rise (4) Without flow regulator Zip Service/Maintenance Support 0800 077 8302 29 Accessories Touch-Free Taps Suitable for use with the Zip InLine range Long reach, basin/sink tap Standard reach, basin/sink tap 130 110 145 30 126 TF001—Mains powered TF003—Mains powered. TF002—Battery powered TF004—Battery powered. Accessories For optimum performance the following tap spray nozzles and handsets should be used with the Zip InLine range Product Code and Description Flow Rates from: Tap Spray Nozzle ZL002—22mm female thread ZL003—24mm male thread 2 litres/min 2 litres/min Tap Aerator Nozzle ZL008—15mm insert ZL004—22mm female thread ZL005—24mm male thread 3.5 litres/min 3.5 litres/min 3.5 litres/min Spray pattern Aerator pattern Shower Hand Set ZL006—Fixed Pattern 4 litres/min Shower Hand Set ZL007—4 Mode Adjustable 4 litres/min 31 Instantaneous Performance Chart Single phase Delivered Temp (˚C) with 12˚C ambient 60 ES3 ES4 ES6 ILX006/CEX ILX009/CEX 55 50 45 40 35 30 25 0.0 1.0 2.0 3.0 4.0 Flow Rate (l/min) Zip Technical Support 0845 602 4533 32 5.0 6.0 Instantaneous Performance Chart Three phase Delivered Temp (˚C) with 12˚C ambient 65 ILX012 DEX/DBX (18kW) DEX/DBX (21kW) DEX/DBX (24kW) DEX/DBX (27kW) 60 55 50 45 40 35 30 4.0 5.0 6.0 Flow Rate (l/min) 7.0 8.0 9.0 10.0 11.0 12.0 13.0 14.0 mixed with cold water at the outlet Zip Service/Maintenance Support 0800 077 8302 33 Application and accessory guide Single phase Flow rate (litres/min) ES ES3 ES4 ES6 ILX006/CEX ILX009/CEX 3.1kW 4.8kW 6.0kW 7.2kW 9.6kW 1 basin 1.7 2.6 3.3 4.0 5.0 2 basins - - - - 2.5 3 basins - - - - - 1 sink - - - - 3.6 2 sinks - - - - - 1 shower - - - - 5.0 2 showers - - - - - 1 bath - - - - - Application Handwash @ 38°C Kitchen sink @ 50°C ILX/CEX Shower @ 38° Bath @ 38°C Recommended accessories Spray nozzle included Aerator nozzle included No accessories required Spray nozzle ZL002/003 Aerator nozzle ZL004/005 Handset ZL006/007 All flow rates at 240V with 12°C supply temperature 34 Application and accessory guide Three phase Flow rate (litres/min) ILX ILX012 DBX18 DBX21 DBX24 DBX27 13.5kW 18kW 21kW 24kW 27kW 1 basin 6.0 8.0 8.0 8.0 8.0 2 basins 3.0 4.0 4.0 4.0 4.0 3 basins - 2.7 2.7 2.7 2.7 1 sink 5.0 6.8 7.9 8.0 8.0 2 sinks - 3.4 4.0 4.0 4.0 1 shower 6.0 8.0 8.0 8.0 8.0 2 showers - 4.0 4.0 4.0 4.0 1 bath - 8.0 8.0 8.0 8.0 Application Handwash @ 38°C Kitchen sink @ 50°C DEX Shower @ 38° Bath @ 38°C Recommended accessories Spray nozzle included Aerator nozzle included No accessories required Spray nozzle ZL002/003 Aerator nozzle ZL004/005 Handset ZL006/007 All flow rates at 400V with 12°C supply temperature 35 Zip sets new standards in Customer Care with the largest team of directly employed engineers in its sector, providing comprehensive on-site maintenance, repair and installation packages Zip Heaters (UK) Ltd Bertie Ward Way, Dereham, Norfolk NR19 1TE Telephone: 0845 602 4533 E-mail: sales@zipheaters.co.uk Website: www.zipheaters.co.uk
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Create Date : 2011:10:13 12:41:30Z Creator : QuarkXPress(R) 7.5 Modify Date : 2011:10:28 09:47:12+01:00 X Press Private : %%DocumentProcessColors: Cyan Magenta Yellow Black.%%EndComments XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Creator Tool : QuarkXPress(R) 7.5 Metadata Date : 2011:10:28 09:47:12+01:00 Producer : QuarkXPress(R) 7.5 Format : application/pdf Title : Layout 1 Document ID : uuid:bf43ed98-2d1f-40a1-99e1-13b213212191 Instance ID : uuid:d0e6b4b8-fdb5-4351-8b3b-8044b618e870 Page Count : 36EXIF Metadata provided by EXIF.tools