Zip Product Guide

User Manual: Zip Product Guide

Open the PDF directly: View PDF PDF.
Page Count: 53

Boiling water
Chilled water
Hot water
Filtration
2012
2 3
Introduction
Every working day in the UK over eight million cups of tea or coffee are
made using Zip instant boiling water products. The launch of Hydroboil
into the UK market in the late 80s revolutionised boiling water delivery
in the workplace and brought new levels of efficiency, safety and user
satisfaction to commerce, industry and the public sector. Today in-
stant boiling water is firmly established as the workplace norm with
Zip the clear market leader.
More recently Zip HydroTap systems have brought further innovation
to the market with under counter units providing instant delivery of fil-
tered boiling and chilled water through easily accessible counter
mounted taps.
Zip also offers a comprehensive range of top quality, value for money
commercial electric water heating products - both vented and un-
vented - from 5 to 300 litre capacity. This is supported by a range of
instantaneous water heaters and a wide selection of water chillers.
The Zip range is in daily use in tens of thousands of locations through-
out the UK including the Houses of Parliament, numerous Blue Chip
Companies, Hospitals, Schools, Military Establishments and HM Pris-
ons as well as many homes.
All products are available nationally through electrical wholesalers and
plumbing merchants.
Zip’s experienced team of Training Managers offer bespoke product
training geared to the needs of Installers, Specifiers and Facility Man-
agers. These ‘hands on’ sessions typically take place on site and cover
all relevant product installation, servicing and maintenance issues. In
addition a choice of RIBA accredited CPD programmes is available.
Zip products are inherently reliable and covered by comprehensive on
site parts and labour warranties – details of which may be found at:
www.zipheaters.co.uk/warranty
To support these guarantees and provide comprehensive service sup-
port packages ranging from out of warranty repair to comprehensive
maintenance programmes, Zip has the largest team of directly em-
ployed Engineers in the UK focused solely on boiling water, chilled
water and commercial water heating products.
Zip is committed to Customer Satisfaction and offers support and ad-
vice to Specifiers, Installers and End Users alike. Whether the query re-
lates to the specification, installation or use of our products, the Zip
Technical Advice Team is just a phone call away.
Whatever the boiling, chilled or hot water need, Zip has the ultimate
solution.
Index
NEW PRODUCTS 6-7
Drinking Water - Boiling
HydroTap introduction 8-13
Boiling & chilled 14-15
Boiling 16-17
Chilled 18-19
3-in-1 & 4-in-1 20-21
All-in-One 22-23
Industrial 24-25
HydroTap for the Home 26-29
HydroTap options and filtration 30-33
Wall Mounted instant boiling water overview 34-35
Hydroboil Plus 36-37
Hydroboil 38-39
Econoboil 40-41
Duo 42-43
Accessories 44-45
Drinking water - Chilled
Chilled water introduction 46-47
HydroTap chilled 48-49
Chilltap 50-51
Chillmaster 52-53
Wall Fountain 54-55
Chill Fountain 56-57
Chilled and filtered water for the Home 58-61
Accessories 62-63
Hot water
Hot water introduction 64-65
InLine introduction 66-67
ES & Kits 68-71
ILX 72-73
CEX 74-75
DEX & DBX 76-77
InLine accessories 78-79
Aquapoint III unvented 5-15 litres 80-81
Varipoint II unvented 10 & 15 litres 82-83
Unvented accessories 84-85
Aquapoint III unvented 30-100 litres 86-87
Varipoint III unvented 30-100 litres 88-91
AquaFlo 92-93
Tudor 94-95
Contract 96-97
RCH 98-99
Applications & General Data 100-101
4 5
Zip Hydroboil Plus
In response to customer de-
mand the existing range
of Hydroboil Plus capacities
is extended to include 10, 15,
25 and 40 litre units, making
them the most energy efficient
in the industry.
See pages 36-37
Zip HydroTap Finishes
In addition to the standard Bright Chrome finish traditional HydroTap is
now available in a choice of Brushed Chrome, Black Chrome and
Gold Plated finishes. See page 30
Zip HydroTap Miniboil
Super-compact, economy
models for filtered boiling and
filtered cold (ambient) water.
See pages 28-29
Zip New Products
67
Zip HydroTap Industrial
Models are designed to withstand
the heavy usage associated with
shop floor, canteen and institutional
environments.
See pages 24-25
Zip HydroTap All-in-One
Systems deliver instant boiling
and chilled filtered drinking water
and hot, warm or cold water
through one stylish tap.
See pages 22-23
Zip HydroTap+
Models feature increased cups
per hour boiling water capacity
and a ‘free-flow’ chilled water
capability.
See pages 15, 21, 23 & 25
Classic tap Elite tap
Zip DEX, DBX & CEX
New ranges of high efficiency electronically controlled
instantaneous electric water heaters for single or multiple outlets.
See pages 74-77
Zip Chilltap Extra
Chilled filtered water, instantly,
plus filtered cold (ambient) water.
Fingertip control for filling cups
and hands-free filling for large jugs.
Superior submicron filtration.
See pages 60-61
Drinking water
8
Zip HydroTap brings, with one system, all the practical advantages of
instant boiling and chilled filtered water to commercial environments
such as offices, factories and hospitals, as well as in the home.
Zip HydroTap®
Changing the way the world boils water
Press lever down to fill
cups, teapots, etc.
When activated the safety
interlock requires finger-
thumb operation
Pull lever forward to fill large
vessels and for measured
delivery
Instant boiling and chilled
filtered water from a single
tap.
A touch of the red lever provides
instant filtered boiling water,
whilst the blue lever delivers
fresh tasting filtered chilled
water.
Features and benefits
Programmable energy saving
modes for added efficiency.
Programmable maximum
measured water delivery.
Safety interlock provides user
with added protection where
needed.
System unit hidden under the
counter.
Filter change warning light.
No more time wasted waiting for
a kettle to boil.
No more energy wasted boiling
kettles or urns.
No more bottled water to buy.
No more bottled water to store.
No more bottled water to
handle.
No more running out of drinking
water during periods of high
demand, such as hot weather.
Features the most technically
advanced submicron filtration
system for healthier, better
tasting drinking water.
Option of anti-scale filter.
Installation at the sink or on
optional font and drain.
Drinking water
9
Drinking water
10
Drinking water
11
Zip HydroTap®technology
Superior technology saves energy and
conserves water
Zip HydroTap®efficiency
Typical energy efficiency information—
commercial models
Power-Pulse™ energy saving technology
Reduces power consumption by allowing the system to
regulate its power during periods of high and low usage.
This saves energy whilst maintaining the tightest
possible temperature control.
Cuts energy consumption
Running costs: no more than 15p per day (with sleep
mode active 10 hours in 24), plus boiling water 8 cups
for 1p; chilled water 20 glasses for 1p.
Sleeps when inactive
The system can be pre-set to power down after 2 hours
of non-use, but will still retain stored ‘boiling’ water at an
energy saving 65°C. The system quickly recovers to the
pre-set boiling temperature upon further draw-off.
Programmable 24/7 timer
Pre-set the ‘power on’ and ‘power off’ times (once a
day) for those periods when the Zip HydroTap will not be
used, such as overnight or at weekends (for commercial
users).
N.B. To calculate a total running cost figure, add the cost per day
to the number of cups of boiling water consumed, multiplied by the
cost (at 8 cups for 1p) and the number of glasses of chilled water
consumed, multiplied by the cost (at 20 glasses for 1p).
Methodology:
Typical results of test carried out for Zip and independently
verified by The University of New South Wales, Australia
Assumed typical business day; 12 hours operational mode, 12
hours sleep mode, 10 minutes full recovery mode
Operational mode is the default setting; with the main system
using sufficient power to maintain set temperature in the tanks
Sleep mode—system powers down if not used for two hours,
using only enough energy to maintain ‘boiling’ water at 66°C
Test conditions—boiling water at 98°C and chilled water at
between 5°C and 10°C
The CO2emission estimates are based on 430 kg of CO2per
1000 kWh of electrical power consumed
The estimated cost per day is based on £0.10 per kWh
Standard cup 167ml. Standard glass 200ml.
Typical 24-Hour Business Day
Model Power Usage CO2Emission Cost per day
(Watt hours) (kg) (£)
BC150/175 1,481 0.637 0.15
BC100/125 1,357 0.584 0.13
For each cup of boiling water or glass of chilled water
Model Power Usage CO2Emission Cost
(Watt hours) (kg) (£)
Boiling cups 13.0 0.006 0.0013
Chilled glasses 6.0 0.003 0.0006
Plus
Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
Drinking water
12
Drinking water
13
Zip HydroTap®range
General Information—Commercial
HydroTap
Zip HydroTap®range
The wide range of products available
Tap head
Chrome plated, die cast tap
body with push and pull levers.
Intergral safety lock and LED
indicators.
Disabled option
Oversize tap levers.
Control panel
Located on undercounter unit for
programming sleep mode, timer,
water temperature and water
delivery.
Filtration system
Integral triple-action submicron
encapsulated cartridge.
(See page 33)
Safety features
Safety interlock on tap.
Undercounter safe tray with leak
detector.
Finishes
Available in Bright Chrome
(standard), Brushed Chrome,
Black Chrome and Gold Plated.
Approvals
WRAS, CE endorsed.
Warranty
1 year on site parts and labour.
For full details visit:
www.zipheaters.co.uk/warranty
Plumbing
The water supply must be
potable (drinkable).
If static pressure exceeds 7 bar,
a pressure reducing valve must
be fitted.
An isolating valve should be
installed between the water
supply and the unit.
Venting
The cupboard housing the unit
must be amply ventilated by
using the 4mm buffers and vent
provided.
Electrical
To be wired to a double pole
switched fused spur with a
minimum break capacity of 13
amp.
Installation must comply with
current IEE regulations.
3 metre power cable provided.
Caution
In some hard water areas where
scale is an issue we recommend
the fitting of the Zip FL3000 scale
management system (see page
33).
Boiling & chilled
Chilled only
For the Home
Boiling only
4-in-1 & 3-in-1
All-in-One Industrial
HydroTap sink mounted
Allow 35mm hole for
fixing to surface or sink
HydroTap font mounted
Allow 35mm hole for tap and
108mm for font
(template supplied)
Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
Drinking water
Drinking water
Zip HydroTap®
Filtered boiling and chilled water
Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
Features & benefits
Provides boiling and chilled
filtered water instantly from a
single tap
Saves time with staff waiting
for a kettle to boil
No unsightly and unsafe kettle
leads
More environmentally friendly
than a kettle
Provides more choice of
beverage than a vending
machine
No need for expensive and
environmentally damaging
bottled water
No need to store and handle
bottled water
No fear of running out of
drinking water in extreme
weather conditions
Can be sited at a sink or
away from it on the optional
font and drain
Choice options
For medium sized locations
choose BC160/125+.
For large locations choose
BC200/175+.
‘+’ signifies models are ‘freeflow’,
ensuring cold water continues to
flow when ‘chilled glasses per
hour’ is exceeded during periods
of high demand.
Boiling system
Open outlet, vented; designed to
operate at 98°C.
Chilling system
Fan-cooled condenser type.
Refrigerant
R134A.
Temperature settings
The boiling temperature can be
adjusted from 99°C to 6C.
N.B. For general installation and
specification details of the
HydroTap range see page 12.
14 15
Product Maximum Maximum Power Dimensions
Code Boiling Chilled Rating W x D x H
cups/hour glasses/hour kW @ 230V (mm)
BC200/175+ 200 175 2.8 500 x 465 x 395
BC160/125+ 160 125 2.3 440 x 430 x 337
‘+’ signifies models are free flow, ensuring cold filtered water continues when ‘chilled
glasses/hour’ is exceeded during periods of high demand.
Standard cup 167ml. Standard glass 200ml.
Energy Conservation
A choice of two programmable energy saving modes –
Integral 24 hour 7 day timer enables the boiling and chilled water
units to switch off automatically during known periods of inactivity
e.g. overnight or weekends, but return to full functionality ahead of
the next expected demand.
Inactivity Sleep Mode enables the boiling water unit to power down
or switch off after 2 hours non-use. Powering down allows the water
temperature to gradually reduce to 65˚C, at which it is maintained.
Upon further draw off boiling resumes.
Drinking water
Drinking water
16 17
Zip HydroTap®
Filtered boiling water
Features and benefits
Provides boiling filtered water
instantly
Saves time with staff waiting
for a kettle to boil
No unsightly and unsafe kettle
leads
More environmentally friendly
than a kettle
Provides more choice of
beverage than a vending
machine
Can be sited at a sink or away
from it on the optional font and
drain
Choice options
For small and medium sized
locations choose B160F.
For large locations choose B200F.
Boiling system
Open outlet, vented; designed to
operate at 98°C.
Temperature settings
The boiling water temperature can
be adjusted from 99°C to 68°C.
N.B. For general installation and
specification details of the
HydroTap range see page 12.
Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
Product Maximum Maximum Power Dimensions
Code Boiling Chilled Rating W x D x H
cups/hour glasses/hour kW @ 230V (mm)
B200F 150 2.6 310 x 340 x 393
B160F 100 2.1 280 x 323 x 337
Standard cup 167ml.
Energy Conservation
A choice of two programmable energy saving modes –
Integral 24 hour 7 day timer enables the boiling and chilled water
units to switch off automatically during known periods of inactivity
e.g. overnight or weekends, but return to full functionality ahead of
the next expected demand.
Inactivity Sleep Mode enables the boiling water unit to power down
or switch off after 2 hours non-use. Powering down allows the water
temperature to gradually reduce to 65˚C, at which it is maintained.
Upon further draw off boiling resumes.
Drinking water
18
Drinking water
19
Zip HydroTap®
Filtered chilled water
Features and benefits
Provides chilled filtered water
instantly
No need for expensive and
environmentally damaging
bottled water
No need to store and handle
bottled water
No fear of running out of
drinking water in extreme
weather conditions
Can be sited at a sink or away
from it on the optional font
and drain
Choice options
For small to medium sized
locations choose C125.
Chilling system
Fan-cooled condenser type.
Refrigerant
R134A.
Temperature settings
The chilled water temperature is
factory set to deliver water at be-
tween 5°C to 10°C.
N.B. For general installation and
specification details of the
HydroTap range see page 12.
Product Maximum Maximum Power Dimensions
Code Boiling Chilled Rating W x D x H
cups/hour glasses/hour kW @ 230V (mm)
C125 125 0.2 306 x 457 x 334
Standard glass 200ml.
Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
Energy Conservation
Programmable operation
Integral 24 hour 7 day timer enables the chilled water unit to switch
off automatically during known periods of inactivity e.g. overnight or
weekends, but return to full functionality ahead of the next expected
demand.
Drinking water
Drinking water
20 21
Features & benefits
Offers all of the advantages of a
standard HydroTap plus these ad-
ditional 4 benefits.
Provides hot water at 50°C
to the mixer tap (supplied)
and either boiling and chilled
(4-in-1) or boiling (3-in-1) to
the HydroTap
Saves the cost of a separate
hot water supply
Saves space
Conserves energy
Choice options
3-in-1
For small to medium sized locations
choose BH160F.
For large locations choose BH200F.
4-in-1
For small to medium sized locations
choose BCH160/125+.
For large locations choose
BCH200/175+.
‘+’ signifies models are ‘freeflow’,
ensuring cold water continues to
flow when ‘chilled glasses per
hour’ is exceeded during periods
of high demand.
Boiling system
Open outlet, vented; designed
to operate at 98°C.
Chilling system
Fan-cooled condenser type.
Refrigerant
R134A.
Temperature settings
The boiling water temperature can
be adjusted from 99°C to 68°C.
Mixer Flow
The mixer tap will deliver up to
3ltr/min, ideal for rinsing cups and
handwashing.
N.B. For general installation and
specification details of the
HydroTap range see page 12.
Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
Zip HydroTap®3-in-1 & 4-in-1
Boiling and chilled filtered drinking water
PLUS hot, cold (ambient) or mixed
warm water – all from a single source
4-in-1 provides filtered boiling and chilled water delivered through
the HydroTap PLUS hot and cold (ambient) through the mixer tap.
3-in-1 provides filtered boiling water delivered through the Hydro-
Tap PLUS hot and cold (ambient) through the mixer tap.
Energy Conservation
A choice of two programmable energy saving modes –
Integral 24 hour 7 day timer enables the boiling and chilled water
units to switch off automatically during known periods of inactivity
e.g. overnight or weekends, but return to full functionality ahead of
the next expected demand.
Inactivity Sleep Mode enables the boiling water unit to power down
or switch off after 2 hours non-use. Powering down allows the water
temperature to gradually reduce to 65˚C, at which it is maintained.
Upon further draw off boiling resumes.
Product Maximum Maximum Power Dimensions
Code Boiling Chilled Rating W x D x H
cups/hour glasses/hour kW @ 230V (mm)
BH200F 200 - 2.6 310 x 340 x 393
BH160F 160 - 2.1 280 x 323 x 337
BCH200/175+ 200 175 2.8 500 x 465 x 395
BCH160/125+ 160 125 2.3 440 x 430 x 337
‘+’ signifies models are free flow, ensuring cold filtered water continues when ‘chilled
glasses/hour’ is exceeded during periods of high demand.
Standard cup 167ml. Standard glass 200ml.
Drinking water
22
Drinking water
23
Zip HydroTap®All-in-One
(Commercial) NEW
Boiling and chilled filtered drinking water
PLUS hot, cold (ambient) or mixed
warm water – all from one tap
Features & benefits
Offers all of the advantages of a
standard HydroTap plus the
additional benefits.
Replaces mixer taps to
declutter and simplify kitchen
design
Vented systems save space,
cost and energy by eliminating
the need for a separate hot
water supply
Separate drinking water
controls for convenience and
safety
Vented and non-vented
systems available
Choice options
Non-vented systems
(Uses an existing hot water
supply to feed mixed hot water
to the All-in-One Tap).
For small to medium locations
choose BC160/125+A.
For large locations choose
BC200/175+A.
Vented systems
(Uses incoming cold water
supply heated in the HydroTap
system to provide mixed hot
water to the All-in-One Tap).
The hot water system mixes
boiling and cold water to
approximately 50°C.
For small to medium sized
locations choose
BC160/125+AV.
For large locations choose
BC200/175+AV.
‘+’ signifies models are
‘freeflow’, ensuring cold water
continues to flow when ‘chilled
glasses per hour’ is exceeded
during periods of high demand.
Tap head
Long reach spout swings to
service two sinks.
N.B. For general installation and
specification details of the
HydroTap range see page 12.
Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
Product Maximum Maximum Power Dimensions
Code Boiling Chilled Rating W x D x H
cups/hour glasses/hour kW @ 230V (mm)
BC200/175+AV 200 175 2.8 500 x 465 x 395
BC160/125+AV 160 125 2.3 440 x 430 x 337
BC200/175+A 200 175 2.8 500 x 465 x 395
BC160/125+A 160 125 2.3 440 x 430 x 337
‘+’ signifies models are free flow, ensuring cold filtered water continues when ‘chilled
glasses/hour’ is exceeded during periods of high demand.
‘A’ signifies non-vented models where the system uses an existing hot water feed the
mixed hot water to All-in-One tap.
‘AV’ signifies vented models where the system uses incoming cold water and heats it
using the HydroTap boiling process to provide mixed hot water to the All-in-One tap.
Standard cup 167ml. Standard glass 200ml.
Energy Conservation
A choice of two programmable energy saving modes –
Integral 24 hour 7 day timer enables the boiling and chilled water
units to switch off automatically during known periods of inactivity
e.g. overnight or weekends, but return to full functionality ahead of
the next expected demand.
Inactivity Sleep Mode enables the boiling water unit to power down
or switch off after 2 hours non-use. Powering down allows the water
temperature to gradually reduce to 65˚C, at which it is maintained.
Upon further draw off boiling resumes.
Drinking water
Drinking water
24 25
Zip HydroTap®in Industry NEW
Heavy duty designs for industrial
environments and institutions
Features & benefits
Offers all of the advantages of a
standard HydroTap plus these
additional benefits.
Super strong tapered shank
anchor (side touch models)
Damage-resistant side or top
touch buttons
Simple 2-button without safety
lock
Optional 3-button with safety
lock
Can be installed R/H or L/H
Up to 200 boiling cups per
hour
Up to 175 chilled glasses per
hour
Features ‘Free-Flow’, ensuring
cold filtered water continues
to be available even when
‘chilled glasses per hour’
capacity is exceeded
Side touch variant (primarily
for institutional use) has a high
strength tapered base which
fastens to an undersink clamp
block with a reinforcing spine
Choice options
Top-Touch models
For heavy duty small to medium
sized locations choose
BC160/125+IT.
For heavy duty large locations
choose BC200/175+IT.
Side-Touch models
For heavy duty small to medium
sized locations where additional
security is needed choose
BC160/125+IS.
For heavy duty large locations
where additional security is
needed choose BC200/175+IS.
Tap Head
Chrome Plated.
N.B. For general installation and
specification details of the
HydroTap range see page 12.
Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
Product Model Max Max Power Dimensions
Code Type Boiling Chilled Rating W x D x H
cups/ glasses/ kW @ (mm)
hour hour 230V
BC200/175+IT Boiling/Chilled 200 175 2.8 500 x 465 x 395
with top-touch tap
BC160/125+IT Boiling/Chilled 160 125 2.3 440 x 430 x 337
with top-touch tap
BC200/175+IS Boiling/Chilled 200 175 2.8 500 x 465 x 395
with side-touch tap
BC160/125+IS Boiling/Chilled 160 125 2.3 440 x 430 x 337
with side-touch tap
‘+’ signifies models are free flow, ensuring cold filtered water continues when ‘chilled
glasses/hour’ is exceeded during periods of high demand.
Standard cup 167ml. Standard glass 200ml.
Energy Conservation
A choice of two programmable energy saving modes –
Integral 24 hour 7 day timer enables the boiling and chilled water
units to switch off automatically during known periods of inactivity
e.g. overnight or weekends, but return to full functionality ahead of
the next expected demand.
Inactivity Sleep Mode enables the boiling water unit to power down
or switch off after 2 hours non-use. Powering down allows the water
temperature to gradually reduce to 65˚C, at which it is maintained.
Upon further draw off boiling resumes.
Drinking water
27
Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
Zip HydroTap®for the Home
Instant boiling and chilled filtered water
systems for home kitchens, large and
small, traditional or contemporary
Features and benefits
No more waiting for water to boil
No more bottled water to buy
Easy to use
Submicron filtration for great
tasting healthy water
Scale management filter option
Can be sited next to sink or on
optional font and drain
Highly energy efficient
Child safety interlock
Tap levers can be ‘locked’ for
filling of large vessels
Measured dispense when
levers are in upright position
Power-pulse energy saving
technology
Sleep mode to save power
Integral 24/7 timer
Running costs of no more
than 15p per day plus 8 cups
of boiling water for 1p and 20
glasses of chilled water for 1p.
Models available
Boiling and chilled filtered
water
Boiling and chilled split
(separate units)
Boiling and cold (ambient)
filtered water
Boiling filtered water
Chilled filter water
All-in-One model with boiling,
chilled, hot and cold water
from one tap.
Choice of four tap and font
finishes (except for All-in-One)
Warranty
24 months on site parts and
labour warranty subject to
registration. These products are
specifically designed for use in
domestic environments. Use of
them in commercial applications
may invalidate the warranty.
N.B. For further details see Zip
Brochure ‘Treat Yourself to a
New Way of Life’ or visit:
www.zipheaters.co.uk
Product Model Boiling Chilled Total Undersink
Code Type Chamber Chamber Rating W x D x H
(litres) (litres) kW (mm)
DOMBC1 Boiling & Chilled 1.8 1.8 1.7 385 x 380 x 348
DOMBC2 Boiling & Chilled split 1.8 1.8 1.7 280 x 323 x 337
353 x 253 x 377
DOMBA1 Boiling & Ambient 1.8 1.5 280 x 323 x 337
DOMHB1 Boiling only 1.8 1.5 188 x 320 x 334
DOMBC1A All-in-One 1.8 1.8 1.8 385 x 380 x 348
DOMC1 Chilled only 1.8 0.3 306 x 457 x 334
Drinking water
HydroTap font mounted
Allow 35mm hole for tap
fixing and 108mm for font
(template supplied)
All-in-one sink mounted
Allow 35mm hole for
fixing to surface or sink
26
Drinking water
29
Zip HydroTap®
Miniboil Classic & Elite NEW
Super compact economy models for
filtered boiling and filtered cold
(ambient) water for the home
Drinking water
28 Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
Models available
Boiling and cold (ambient)
filtered water with Classic tap
Boiling and cold (ambient)
filtered water with Elite tap
Features and benefits
No more waiting for water to
boil
Easy to use touch pads
Submicron filtration for great
tasting healthy water
Scale management filter option
Can be sited next to sink or on
optional font and drain
Inactivity sleep mode
Filter change indicator
Cool-touch tap
Compact size makes it ideal
for kitchens with limited space
Highly energy efficient
Safety interlock
Power-Pulse™ technology
Filtration
Supplied with external triple
action sub-micron filter.
Additional anti-scale filtration
option.
Warranty
12 months on site parts and
labour warranty. These products
are specifically designed for use
in domestic environments. Use of
them in commercial applications
may invalidate the warranty.
N.B. For further details see Zip
Brochure ‘Treat Yourself to a New
Way of Life’ or visit:
www.zipheaters.co.uk
Product Model Boiling Total Undersink
Code Type Chamber Rating W x D x H
(litres) kW (mm)
Boiling & Cold
MB1BA Classic Tap 1.8 2.0 212 x 272 x 338
Boiling & Cold
MB2BA Elite Tap 1.8 2.0 212 x 272 x 338
Tap mounted on font
Allow 35mm hole for tap
fixing and 108mm for font
(template supplied)
Tap mounted on sink
Allow 35mm hole for tap
fixing to surface or sink
Zip Miniboil Elite
Zip Miniboil Classic Miniboil shown font mounted.
Drinking water
Drinking water
30 31
Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
Zip HydroTap®Options
Finishes and practical solutions
Font and Drain
Zip HydroTap can be ordered
with a matching font and
drain for mounting remotely
from the sink.
Order Codes:
ZT004 – Chrome
ZT104 – Brushed Chrome
ZT105 – Black Chrome
ZT106 – Gold Plated
Finishes NEW
Traditional Zip
HydroTap and
fonts are available
in standard Bright
chrome and a choice
of three additional
finishes.
Over sized levers
All HydroTap models,
except for models in the
All-in-One, Industrial and
Miniboil ranges, can be
fitted with oversize levers
to assist those with restricted
dexterity.
Add ‘D’ to normal code when
ordering.
Drainless Font
For locations where there is
no available drainage, the Zip
“Drainless Font” system
ensures the safe and
effective collection of waste
water from a HydroTap font.
Order Code:
ZT006
Black Chrome
Add ‘B’ to normal
code when ordering.
Brushed Chrome
Add ‘S’ to normal
code when ordering.
Gold Plated
Add ‘G’ to normal
code when ordering.
Drinking water
Drinking water
32 33
Zip HydroTap®Filtration
All HydroTap products feature
submicron filtration
Triple Action filtration
Uses submicron filters which are
the most technically advanced in
the world.
• Reduces:
Chlorine taste and odour
Dirt, rust, asbestos fibres
and other particulates
Parasitic protozoan cysts
Limescale formation
• Removes:
Micro-organisms down to
1000th of a millimetre
Parasites such as
Cryptosporidium and Gardia
Scale Management
Recommended for use in
locations where limescale is
present (see map opposite).
Eliminates scale up to a
throughput of 3000 litres
Easy to install
Horizontal or vertical mounting
Easy to replace
Reduces bad taste and odour
Four stage filtration
Pre-filter to remove larger
particles
• Ion exchange
• Activated carbon filter
• Fine filter
The sub-micron filter is encased for quick
and easy replacement.
Red
Hard to very hard
Yellow
Medium hardness
Green
Soft
Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
UK Scale Map
Product Description FL3000
codes Dimensions
FL004 Submicron system H x D (mm)
ZT002 Submicron replacement cartridge 490 x 106
FL3000 Limescale filtration system
for vertical or horizontal mounting
FL3001 Limescale replacement cartridge
ZT004 Font and Drain
ZT008 Font and Drain for Miniboil Elite
ZT006 Drainless Font
Drinking water
35
Zip Service/Technical Support 0800 077 8302
Saves time
No more time wasted waiting for
water to boil—Zip delivers boiling
water instantly, at the touch of a
tap.
Saves energy
No energy is wasted boiling more
water than neededfingertip
control gives a cup full or teapot
full at a time.
Saves space
No cluttered worktops—Zip
instant boiling water eliminates
the need for kettles and exposed
power leads.
Saves money
Costs little to run—thanks to
energy-efficient design and
electronic controls (Hydroboil
Plus) to minimise power
consumption.
Sets a new standard
Every working day in the UK over
eight million cups of tea and
coffee are made using Zip instant
boiling water systems.
Temperature control
Zips patented high precision
temperature control systems are
designed to keep the boiling
water within one degree of the
set temperature. This means that
boiling water and only boiling
water is delivered.
Ranges
Zip offers a choice of three
ranges:
Hydroboil Plus
Thermostatically controlled,
twin chamber technology with
stainless steel boiling tank.
Premium insulation and cool
touch two way tap with safety
lock.
Energy saving Power-Pulse
Sleep mode - after 2 hours of no
demand or when lights turned off.
Integral 24 hour 7 day timer.
Available in sizes from 3.0 to
40.0 litres.
White or stainless steel finishes.
Hydroboil
Thermostatically controlled,
twin chamber technology with
stainless steel boiling tank.
Premium insulation and chrome
catering style tap.
Available in sizes from 1.5 to
40.0 litres.
White or stainless steel finishes.
Econoboil
Thermostatically controlled, twin
chamber technology with copper
boiling tank.
Tontine insulation.
Chrome catering style tap.
Available in 3.0 & 5.0 litres.
White finish.
Customer Service 0845 602 4533
34
Drinking water
Overview
Wall mounted instant boiling water
Zip Hydroboil Plus
Zip Hydroboil®
Zip Econoboil
Instant boiling water heaters are essential appliances for the
workplace and are available in the widest range of models and
capacities.
Patented twin chamber
technology – uses steam
to pre-heat incoming
water
Patented Steam-Heat-
Boost system
Patented Teflon me-
tering tube
regulates water
flow & temperature
Moulded high
temperature insulation
minimises boiling water
heat loss
Zip Hydroboil Plus cuts energy
consumption in 5 ways
Steam-Heat-Boost System
Steam from boiling water is recycled to pre-heat incoming
cold water. A patented metering tube maintains the stored
water within 1°C of set temperature.
Power-Pulse™ energy saving technology
Applies full power only during heavy usage periods cutting
back to micro-pulse power during light usage or when un-
used — not available on 40 litre model.
Inactivity sleep mode
After 2 hours of non-use Hydroboil Plus enters sleep mode,
allowing the water temperature to reduce to 65° at which it
is maintained until next draw-off.
Low light sleep mode
When activated, an integral light detector activates this facil-
ity when room light is switched off and the unit enters sleep
mode as above.
Integral 24 hour 7 day timer
Switches system off during known periods of inactivity,
returning to full functionality ahead of next expected de-
mand.
Drinking water
Drinking water
36 37
Zip Hydroboil Plus
Wall mounted instant boiling water
3, 5, 7.5, 10*, 15*, 25*, 40*litre
*NEW
Heating element
Long-life incoloy sheathed
embedded rod type.
Dry start protection.
Boiling chamber
Twin chamber-stainless steel.
Steam-Heat-Boost technology.
Crevice-free stainless steel with
removable access ports, top and
bottom.
Insulation
Compressed high temperature
insulation panels on sizes below
10 litres, engineered for easy
boiling chamber access. High
efficiency aluminium backed
mineral wool insulation on other
sizes.
Thermostat
Thermistor controlled.
Case
Stainless steel or corrosion-
resistant, white enamelled steel.
Temperature Settings
On installation, to suit user needs,
the boiling water temperature can
be adjusted from 100˚C to 68˚C.
Control Panel
Liquid Crystal Display shows time,
day, heater operation and energy
saving mode status. If used with
an in-line filter, a filter change re-
minder can be programmed.
Tap
Unique two-way cool touch tap.
Safety features
Integral safety lock.
Approvals
WRAS, CE endorsed.
Warranty
Two-year on site parts and
labour. For full details of the Zip
Warranty visit:
www.zipheaters.co.uk/warranty
Installation
Install over a draining board, or
work top fitted with a drip tray.
Tap spout should be no higher
than necessary to fill large pots.
Minimum tap height above
draining board for on-wall
maintenance is 200mm.
Plumbing
Designed for direct connection to
a potable cold water supply with
a minimum pressure of 1 bar. If
pressure exceeds 7 bar a
pressure limiting valve must be
fitted. An isolating valve should
be installed between the water
supply and the heater.
Concealed plumbing
Connect inlet and vent pipes from
the rear via 15mm capillary elbows.
Exposed plumbing
Connect inlet and vent pipes
from below directly to 15mm
compression fittings.
Venting
The vent must discharge to a
safe visible position using a
tundish.
Electrical
To be wired to a double pole
fused spur with a minimum break
capacity of 13 amps. Installation
must comply with current IEE
regulations.
Caution
In some hard water areas where
scale is an issue we recommend
the fitting of the Zip InLine filter.
Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
Energy Conservation
The installer can select one of two programmable energy
saving modes –
Integral 24 hour 7 day timer enables the unit to switch off
automatically during known periods of inactivity e.g. overnight or at
weekends, returning to full functionality ahead of the next expected
demand.
Sleep Modes
Inactivity Sleep Mode. Following a period of 2 hours non-use
Hydroboil Plus automatically enters sleep mode when the unit powers
down allowing the water temperature to gradually reduce to 65˚C, at
which it is maintained. Upon further draw off boiling resumes.
and/or
Low light Sleep Mode. An integral light detector automatically
activates sleep mode (as above) when room lights are switched off,
returning to normal operation when the next draw off occurs or the
lighting is switched back on.
Zip Hydroboil Plus with cool touch tap and energy saving features
Product Code Capacity Delivery Recovery Rating Dimensions
Case Finish litres cups*at any cups* kW H x W x D
s/steel white one time per hour (@ 230V) (mm)
HP103 HP003 3.0 18 100 1.5 431 x 289 x 180
HP105 HP005 5.0 30 140 2.4 465 x 318 x 198
HP107 HP007 7.5 45 140 2.4 578 x 318 x 198
HP110 HP010 10.0 60 180 3.0 600 x 390 x 244
HP115 HP015 15.0 90 180 3.0 600 x 390 x 299
HP125 HP025 25.0 150 180 3.0 780 x 390 x 299
HP140 HP040 40.0 240 360 2 x 3.0 840 x 515 x 284
*Standard cup size 167ml
Drinking water
38
Drinking water
39
Zip Hydroboil®
Wall mounted instant boiling water
1.5, 3, 5, 7.5, 10, 15, 25, 40 litre
Heating element
Long-life incoloy sheathed
embedded rod type. Dry start
protection.
Boiling chamber
Twin chamber-stainless steel.
Steam-Heat-Boost technology.
Crevice-free stainless steel with
removable access ports, top
and bottom.
Insulation
Compressed high temperature
insulation panels on sizes below
10 litres, engineered for easy
boiling chamber access. High
efficiency aluminium backed
mineral wool insulation on other
sizes.
Thermostat
Capillary type.
Case
Stainless steel or corrosion
resistant white enamelled steel.
Tap
Two way, chrome-plated classic,
catering style.
Approvals
WRAS, CE endorsed.
Warranty
Two-year on site parts and
labour. For full details of the Zip
Warranty visit:
www.zipheaters.co.uk/warranty
Installation
Install over a draining board, or
work top fitted with a drip tray.
Tap spout should be no higher
than is necessary to fill large
pots. Minimum tap height above
draining board for on-wall
maintenance is 200mm.
Plumbing
Designed for connection to a
potable cold water supply with
a minimum pressure of 1 bar. If
pressure exceeds 7 bar a
pressure limiting valve must be
fitted. An isolating valve should
be installed between the mains
supply and the system.
Concealed plumbing
Connect inlet and vent pipes from
the rear via 15mm capillary
elbows.
Exposed plumbing
Connect inlet and vent pipes
from below directly to 15mm
compression fittings.
Venting
The vent must discharge to a
safe and visible position using
a tundish.
Electrical
To be wired to a double pole
fused spur, minimum break
capacity of 13 amps.
Installation must comply with
current IEE regulations.
Caution
In some hard water areas where
scale is an issue we recommend
the fitting of the Zip Inline filter.
Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
Zip Hydroboil®with Classic tap
Product Code Capacity Delivery Recovery Rating Dimensions
Case Finish litres cups*at any cups* kW H x W x D
s/steel white one time per hour (@ 230V) (mm)
HS001 1.5 9 100 1.5 335 x 289 x 180
HS003 3.0 18 100 1.5 431 x 289 x 180
HS105 HS005 5.0 30 140 2.4 465 x 318 x 198
HS107 HS007 7.5 45 140 2.4 578 x 318 x 198
HS110 HS010 10.0 60 180 3.0 600 x 390 x 244
HS115 HS015 15.0 90 180 3.0 600 x 390 x 299
HS125 HS025 25.0 150 180 3.0 780 x 390 x 299
HS140 HS040 40.0 240 360 2 x 3.0 840 x 515 x 284
*Standard cup size 167ml
Drinking water
Drinking water
40 41
Zip Econoboil®
Wall mounted instant boiling water
3 & 5 litre
Heating element
Embedded rod type.
Boiling chamber
Twin chamber in copper.
Steam-Heat-Boost technology.
Insulation
Aluminium backed Tontine.
Thermostat
Capillary type.
Case
Corrosion resistant white
enamelled steel.
Tap
Two way, chrome-plated classic,
catering style.
Approvals
WRAS, CE endorsed.
Warranty
One-year on site parts and
labour. For full details of the Zip
Warranty visit:
www.zipheaters.co.uk/warranty
Installation
Install over a draining board, or
work top fitted with a drip tray.
Tap spout should be no higher
than is necessary to fill large
pots. Minimum tap height above
draining board for on-wall
maintenance is 200mm.
Plumbing
Designed for connection to a
potable cold water supply with
a minimum pressure of 1 bar.
If pressure exceeds 7 bar a
pressure limiting valve must be
fitted. An isolating valve should
be installed between the mains
supply and the system.
Concealed plumbing
Connect inlet and vent pipes
from the rear via 15mm capillary
elbows.
Exposed plumbing
Connect inlet and vent pipes
from below directly to 15mm
compression fittings
Venting
The vent must discharge to a
safe and visible position using a
tundish.
Electrical
To be wired to a double pole
fused spur, minimum break
capacity of 13 amps.
Installation must comply with
current IEE regulations.
Caution
In some hard water areas where
scale is an issue we recommend
the fitting of the Zip Inline filter.
Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
Zip Econoboil
The low cost boiling water solution for locations where economy is of the essence
Product Code Capacity Delivery Recovery Rating Dimensions
Case finish litres cups*at any cups* kW H x W x D
s/steel white one time per hour (@ 230V) (mm)
HS503 3.0 18 100 1.5 431 x 289 x 180
HS505 5.0 30 140 2.4 465 x 318 x 198
*Standard cup size 167ml
Drinking water
43
Drinking water
Zip Duo®
Boiling and chilled filtered water
On-wall fixing or counter-mounted on stand provided
Delivery rate
Up to 100 cups of boiling and 35
glasses of chilled water at a time.
Recovery rate
Up to 217 boiling cups/hour.
90 chilled glasses/hour.
Case
Stainless steel or corrosion-
resistant, white enamelled steel.
Taps
Two way, classic style catering
taps.
Filtration
Integral submicron filtration.
Control panel
For programming sleep mode,
timer and water temperature.
Refrigerant
R134A.
Approvals
WRAS, CE endorsed.
Warranty
One-year on site parts and
labour. For full details of the
Zip Warranty Scheme visit:
www.zipheaters.co.uk/warranty
Temperature Settings
On installation, to suit user
needs, the boiling water
temperature can be adjusted
from 100˚ to 68˚C.
Location
The unit should be positioned
either on a suitable load bearing
wall capable of supporting
42kg - 5 litre, 64kg - 15 litre or
on the counter mounting stand
supplied. The unit must have a
minimum 150mm clearance on
the left, 50mm on the right and
150mm on top.
Minimum tap height, if wall
mounted should be 200mm
above work surface. The vent
must discharge to a safe and
visible place.
Plumbing
The water supply must be
potable (drinkable).
If static pressure exceeds 7 bar,
a pressure reducing valve must
be fitted. An isolating valve
should be installed between the
water supply and the unit.
Electrical
To be wired to a double pole
switched fused spur with a
minimum break capacity of 13
amps (3.5kW 15 amp).
Installation must comply with
current IEE regulations.
HD215 & HD315 should be
provided with their own
dedicated supply.
Caution
In some hard water areas where
scale is an issue we recommend
the fitting of the Zip FL3000
scale management system
(see page 31).
42 Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
Energy Conservation
A choice of two programmable energy saving modes –
Integral 24 hour 7 day timer to enable the boiling and chilled
units to switch automatically off during known periods of inactivity
e.g. overnight or weekends but return to full functionality ahead of
the next expected demand.
Inactivity sleep mode enables the boiling water unit to power
down automatically following a period of 2 hours non-use. This
allows the water temperature to gradually reduce to 65˚C, at
which it is maintained. Upon further draw off boiling resumes.
Zip Duo
Product Code Delivery Recovery Weight Rating Dimensions
Case finish at any one time Cups Glasses kg full kW @ H x W x D
S/Steel White Cups Glasses per hr per hr 230V (mm)
HD105 HD005 30 35 120 90 42 2.0 430 x 650 x 280
HD115 HD015 100 35 140 90 64 2.3 580 x 700 x 350
HD315 HD215 100 35 217 90 64 3.5 580 x 700 x 350
Standard cup 167ml. Standard glass 200ml.
Cup Dispensers
ZE001 Stainless steel
ZE002 White plastic
Counter Stands
ZE004 For HS001
ZE006 For HS003,
ZE007 For HS005, HS105,
HP005, HP105
ZE008 For HS007, HS107,
HP007, HP107
Tundish
ZD100 Wall mounted chromed
tundish
ZD101 Sink mounted chromed
tundish
Universal Mounting Bracket
When a Zip Hydroboil replaces a Heatrae
Sadia, Calomax or Instanta product this
bracket may be used to secure the Hy-
droboil using existing
fixings.
ZP001 3 and 5 litre
ZP002 7.5 litre
Accessories
45
Zip Accessories
Boiling water
Zip Accessories
Boiling water
Accessories
44 Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
Hydroboil Extra Tap Kits
(tap extension pipework)
ZC100 For 10, 15 and 25 litre
heaters, up to 2 taps
(excludes taps)
SP90502 Tap for above
In-Line Filters
FL064 6” filter for taste and
odour removal with scale
reduction. For use with
Hydroboil up to 7.5 litre.
FL104 10” filter for taste and
odour removal with scale
reduction. For use with
Hydroboil 10 litre and
above.
Mug Racks
ZE010 Stainless steel
(for Classic Tap
models only)
ZE011 Stainless steel
(for Hydroboil Plus
models only)
Drip Trays
ZD001 Stainless steel (with drain)
ZD002 Stainless steel (no drain)
Drip Tray
Dimensions
Overview
Chilled, filtered water
Drinking water
Drinking water
Zips mains fed chillers are designed for work place and home
environments, where they provide fresh filtered drinking water.
Features and benefits
Provides drinking water at a fraction of the cost of bottled water
No more bottled water to buy
No more bottled water to store
No more bottled water to handle
No more environmental issues associated with bottled water
No more running out of drinking water during periods of high
demand such as hot weather
Features the most technically advanced submicron filtration
system for healthier, better tasting drinking water
Reduces chlorine taste and odour
Filters out contaminants down to 1 micron
Reduces parasitic protozoan cysts such as Cryptosporidium
and Giardia
Reduces dirt, rust and asbestos fibres
Inhibits the accumulation of limescale deposits
46 47
Zip HydroTap
Zip Chilltap
Zip Chillmaster
Zip Chill Fountain
Zip Wall Fountain
Chilled water for the home NEW
Good hydration
Water is a vital nutrient for life.
Everybody wants to be healthy
both at home and at work, where
a healthier workforce leads to
improved efficiency.
Even mild levels of dehydration
adversely affect both physical
and mental performance.
There is currently no agreement
on how much water we should
drink each day but estimates
range from 1.2 to 3 litres per day.
The need for consumption at the
top of these estimates would
apply to those working in hot or
dusty environments or where
there is a need to wear protective
clothing.
Access to drinking water
The law requires that employers
provide an adequate supply of
wholesome drinking water for all
persons in the workplace. This
must be readily available at
suitable places. Drinking water
should not be sited where
contamination is likely such as
toilet or washroom facilities.
In the home, saving the cost of
bottled water and the advantage
of freeing up space in the fridge
can be a significant benefit.
More information is available from
the Health and Safety Executive
by visiting: www.hse.gov.uk
Source: www.water.org.uk
Drinking water
Drinking water
48 49
Zip HydroTap®
Filtered chilled water system
C Series
Delivery rate
Up to 18 glasses of chilled water
at a time.
Rating
0.3 kW @ 230V AC.
Chilling system
Fan-cooled condenser type.
Refrigerant
R134A.
Tap head
Chrome plated, die cast tap
body with push and pull levers
for electronically controlled water
delivery, integral LED indicators.
Disabled Option
Oversize tap levers.
Under counter unit
Houses chilled and filtration
systems. Corrosion resistant
white enamelled steel case, with
front access door.
Control panel
Located on under counter unit to
control timer and water delivery.
Filtration system
Integral triple-action, submicron,
encapsulated cartridge.
Safety features
Undercounter safe tray with leak
detector.
Approvals
WRAS, CE endorsed.
Warranty
One-year on site parts and
labour. For full details of the
Zip Warranty Scheme visit:
www.zipheaters.co.uk/warranty
Installation
The tap should be positioned
either on a suitable sink or on a
Zip Tap Font. If installing on a
sink, the tap should be mounted
so that it will dispense into the
sink.
The undersink unit should be
located if possible directly
beneath the tap and not more
than 1 metre away. It must be
installed with clearances of
50mm left and right and 65mm
at rear.
Plumbing
The water supply must be
potable (drinkable).
If static pressure exceeds 7 bar,
a pressure reducing valve must
be fitted. An isolating valve
should be installed between the
water supply and the under-
bench unit.
Venting
The cupboard containing the
chilling unit must be amply
ventilated: cupboard doors must
be offset all round for ventilation,
using buffers provided and the
vent fitted (supplied).
Electrical
To be wired to a double pole
switched fused spur with a
minimum break capacity of 13
amps. Installation must comply
with current IEE regulations.
Energy Conservation
Programmable operation
Integral 24 hour 7 day timer enables the chilled water unit to switch
off automatically during known periods of inactivity e.g. overnight or
weekends, but return to full functionality ahead of the next expected
demand.
Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
Product Maximum Maximum Power Dimensions
Code Boiling Chilled Rating W x D x H
cups/hour glasses/hour kW @ 230V (mm)
C125 125 0.2 306 x 457 x 334
Drinking water
50
Product Product Dimensions
Code Type H x W x D
(mm)
CH103 Zip Chilltap, undersink 385 x 355 x 290
Drinking water
51
Zip Chilltap®
Under-sink chiller
Filtered drinking water
Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
sink
Features and benefits
Great tasting freshly filtered
cool drinking water for fitting
on a sink.
Filters out dirt, rust and other
particles contaminating
drinking water.
Reduces chlorine and other
offensive water treatment
chemicals.
Delivers up to 140 glasses
per hour.
Submicron filtration.
Storage capacity
Nominal 8 glasses.
Output capacity
Up to 140 glasses per hour
at <10˚C.
Rating
0.3 kW @ 230V AC.
Chiller type
Fan cooled condenser with
a compressor rated at up to
0.25 hp.
Refrigerant type
Non-toxic R134A.
Under-sink case
Corrosion resistant white
enamelled steel.
Sink mounted tap
Chrome plated brass with lever
action tap and swivel head.
Filtration
Submicron fully encapsulated
externally mounted double action
carbon filter.
Approvals
WRAS, CE endorsed.
Warranty
One-year on site parts and
labour. For full details of the
Zip Warranty Scheme visit:
www.zipheaters.co.uk/warranty
Installation
The tap should be:
Positioned to the rear of a sink.
Mounted on a flat surface.
Mounted at 45 degrees to the
edge of the sink so it drains into
the sink when running.
The under-sink chiller must be:
Located as closely as possible
to, and directly beneath the tap.
Installed with clearances of 50mm
left, right and above, with 65mm
to rear.
Filter should be mounted where
readily accessible on the chiller
or on the adjacent cupboard
wall.
Plumbing
Water connections 15mm push-fit.
If water pressure is above 7 bar a
pressure reducing valve (AQ3)
should be used (see page 82).
Electrical
To be wired to a double pole
switched fused spur with a
minimum break capacity of 13
amps. Installation must comply
with current IEE regulations.
Drinking water
53
Zip Service/Technical Support 0800 077 8302
Product Product Dimensions
Code Type H x W x D
(mm)
CH101 Zip Chillmaster, floor standing 915 x 350 x 350
CH102 Zip Chillmaster, wall mounted 530 x 350 x 350
Features and benefits
Great tasting freshly filtered cool
drinking water for high usage and
public access areas.
Heavy duty, easy-to-clean
stainless steel bowl and stainless
steel case.
Filter change reminder light
signals when filter cartridge
replacement is due.
Filter cartridges are quick and
simple to change.
Submicron filtration.
Storage capacity
Nominal 8 glasses.
Output capacity
140 glasses per hour at <10ºC.
Rating
0.3 kW @ 230V.
Chiller type
Fan cooled condenser with a
compressor rated at 0.25 hp.
Carafe filler
Chrome plated brass lever
action tap with swivel head.
Bubbler
Optional.
Refrigerant type
R134A.
Case
Brushed finish stainless steel
with front access panel.
Filtration
Submicron filtration.
Drain connection 38mm or
43mm diameter.
Approvals
WRAS, CE endorsed.
BREEAM compliance
The Zip Chillmaster is fully
BREEAM compliant when fitted
with ZG500 fitting kit (see page
63).
Warranty
One-year on site parts and
labour. For full details of the
Zip Warranty Scheme visit:
www.zipheaters.co.uk/warranty
Installation
Water, drainage and power should
all be available nearby.
The chiller should be mounted
on a level surface (levelling feet
are provided).
The chiller must be installed with
clearances of 50 mm left, right
and 65mm at rear (except on wall
mounted).
The optional kit ZG500, gives
BREEAM compliance by ensuring
services are protected from
vandalism and the chiller securely
fixed to the wall and floor.
Wall mounted Chillmaster
supplied with 12” masonry
anchors for use on solid walls only.
Plumbing
Water connections 15mm push-fit.
If water pressure is above 7 bar a
pressure reducing valve (AQ3)
should be used (see page 82).
Electrical
To be wired to a double pole
switched fused spur with a
minimum break capacity of 13
amps. Installation must comply
with current IEE regulations.
Drinking water
52 Customer Service 0845 602 4533
Zip Chillmaster®
Floor standing and
wall mounted chiller
Filtered drinking water
Illustrated with a
fitted BREEAM kit
Drinking water
55
Zip Service/Technical Support 0800 077 8302
Drinking water
54 Customer Service 0845 602 4533
Zip Wall Fountain®
Recessed chiller
Filtered drinking water
Features and benefits
Recessed chiller ideal for
providing chilled filtered water
where space is at a premium.
Perfect for installing in busy
corridors.
Submicron filtration.
Storage capacity
Nominal 8 glasses.
Output capacity
Rated at 140 glasses per hour
at <10ºC.
Rating
0.3 kW @ 230V.
Chiller type
Fan cooled condensor with
a compressor rated at 0.25 hp.
Refrigerant type
R134A.
Configuration
Equipped with carafe filler
and bubbler.
Case
Brushed finish stainless steel
with lockable front access panel.
Filtration
Complete with submicron fully
encapsulated double action
carbon filter.
Approvals
WRAS, CE endorsed.
BREEAM compliance
The Zip Wall Fountain is fully
BREEAM compliant when
installed as per fitting
instructions.
Warranty
One-year on site parts and
labour. For full details of the
Zip Warranty Scheme visit:
www.zipheaters.co.uk/warranty
Installation
The chiller should be recessed
into a wall where it is easy for
users to access.
Water, drainage and power
should all be available nearby.
Integral, removable drip tray can
be plumbed into waste if required.
Plumbing
Water connections 15mm push-fit.
If water pressure is above 7 bar a
pressure reducing valve (AQ3)
should be used (see page 82).
Electrical
To be wired to a double pole
switched fused spur with a
minimum break capacity of 13
amps. Installation must comply
with current IEE regulations.
Product Product Dimensions
Code Type H x W x D
(mm)
CH104 Zip Wall Fountain, recessed 1670 x 635 x 303
Drinking water
57
Drinking water
56 Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
303
mm
385mm
Double bowl width
Single bowl width
Product Product type Dimensions
Code Single bowl H x W x D
(mm)
CH105 Zip Chill Fountain (adult) 1140 x 500 x 410
CH145 Zip Chill Fountain (child) 1140 x 500 x 410
CH115 Zip Chill Fountain (wheelchair) 1140 x 500 x 490
Product Product type Dimensions
Code Double bowl H x W x D
(mm)
CH155 Zip Chill Fountain (adult/adult) 1140 x 1005 x 410
CH165 Zip Chill Fountain (child/child) 1140 x 1005 x 410
CH135 Zip Chill Fountain (wheelchair/wheelchair) 1140 x 1005 x 490
CH125 Zip Chill Fountain (adult/child) 1140 x 1005 x 410
CH175 Zip Chill Fountain (adult/wheelchair) 1140 x 1005 x 490
CH185 Zip Chill Fountain (child/wheelchair) 1140 x 1005 x 490
Zip Chill Fountain®
Wall mounted chiller
Filtered drinking water
Features and benefits
The perfect heavy duty
solution for public areas where
configurations for adults, children
or wheelchair access may be
necessary.
Bump action electronic controls
for wheelchair usage and
lockable front panels.
Heavy duty, easy-to-clean
stainless steel bowls and
stainless steel case.
Can be configured for adult, child
or wheelchair usage.
Submicron filtration.
Storage capacity
Nominal 8 glasses.
Output capacity
Rated at 140 glasses per hour
at <10ºC.
Rating
0.3 kW @ 230V.
Refrigerant type
R134A.
Chiller type
Fan cooled condensor with
a compressor rated at 0.25 hp.
Configuration
Can be configured for adult,
child or wheelchair use or any
combination of these.
Case
Brushed finish stainless steel
case with lockable front
access panel.
Filtration
Complete with submicron fully
encapsulated double action
carbon filter.
Approvals
WRAS, CE endorsed.
BREEAM compliance
The Zip Chill Fountain is fully
BREEAM compliant when
installed as per fitting
instructions.
Warranty
One-year on site parts and
labour. For full details of the
Zip Warranty Scheme visit:
www.zipheaters.co.uk/warranty
Installation
The chiller should be wall
mounted where it is easy for
users to access.
Water, drainage and power
should all be available nearby.
Integral, removable drip tray can
be plumbed into waste if required.
Plumbing
Water connections 15mm push-fit.
If water pressure is above 7 bar a
pressure reducing valve (AQ3)
should be used (see page 82).
Electrical
To be wired to a double pole
switched fused spur with a
minimum break capacity of 13
amps. Installation must comply
with current IEE regulations.
Drinking water
59
Drinking water
58 Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
Delivery rate
Up to 18 glasses of chilled water
at a time.
Rating
0.3 kW @ 230V AC.
Chilling system
Fan-cooled condenser type.
Refrigerant
R134A.
Tap head
Chrome plated, die cast tap
body with push and pull levers
for electronically controlled water
delivery, integral LED indicators.
Disabled 0ption
Oversize lever taps.
Under counter unit
Houses chilled and filtration
systems. Corrosion resistant
white enamelled steel case, with
front access door.
Control panel
Located on under counter unit to
control timer and water delivery.
Filtration system
Integral triple-action, submicron,
encapsulated cartridge.
Safety features
Undercounter safe tray with leak
detector.
Approvals
WRAS, CE endorsed.
Warranty
One-year on site parts and
labour. For full details of the
Zip Warranty Scheme visit:
www.zipheaters.co.uk/warranty
Installation
The tap should be positioned
either on a suitable sink or on a
Zip Tap Font. If installing on a
sink, the tap should be mounted
so that it will dispense into the
sink.
The undersink unit should be
located if possible directly
beneath the tap and not more
than 1 metre away. It must be
installed with clearances of
50mm left and right and 65mm
at rear.
Plumbing
The water supply must be
potable (drinkable).
If static pressure exceeds 7 bar,
a pressure reducing valve must
be fitted. An isolating valve
should be installed between the
water supply and the under-
bench unit.
If water pressure is above 7 bar a
pressure reducing valve (AQ3)
should be used (see page 82).
Venting
The cupboard containing the
chilling unit must be amply
ventilated: cupboard doors must
be offset all round for ventilation,
using buffers provided and the
vent fitted (supplied).
Electrical
To be wired to a double pole
switched fused spur with a
minimum break capacity of 13
amps. Installation must comply
with current IEE regulations.
Energy Conservation
Programmable operation
Integral 24 hour 7 day timer enables the chilled water unit to switch
off automatically during known periods of inactivity e.g. overnight or
weekends but return to full functionality ahead of the next expected
demand.
Zip HydroTap
Chilled water for the Home
Product Maximum Maximum Power Dimensions
Code Boiling Chilled Rating W x D x H
cups/hour glasses/hour kW @ 230V (mm)
DOMC1 125 0.3 305 x 455 x 340
Tap mounted on sink
Allow 35mm hole for tap
fixing to surface or sink
Tap mounted on font
Allow 35mm hole for tap
fixing and 108mm for font
(template supplied)
Drinking water
60
Drinking water
61
Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
Chilled Water
For the Home
Features and benefits
Fingertip control for filling glasses
Hands-free filling for large jugs and bottles
Superior sub-micron water filter
Filter change every 12 months
Zip Chilltap Extra NEW
Chilled filtered water, instantly
Plus filtered cold (ambient)
water
Zip Chilltap NEW
Chilled filtered water, instantly
Zip Filter Tap NEW
Filtered cold (ambient) water
Zip Font and Drain
Allows sighting away from the
sink
For connection to waste
Product Zip Chilled Cold Chilled Total Under-sink
Code Model Water Water Glasses/ Rating Dimensions
Hour kW H x W x D
(mm)
DOMCT1 Chilltap ✔✔ 60 0.245 377 x 353 x 253
Extra
DOMCT2 Chilltap 60 0.245 377 x 353 x 253
DOMFT1 Filter Tap –– –
ZT004 Optional font and drain for all above
Drinking water
62
Drinking water
63
Chilled water
Accessories
Chilled water
Accessories
ZE001
Stainless steel dispenser
for disposable cups
ZI001
Optional drinking bubbler
ZD003
Waste water dish for installation
where drainage is not available
Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
BREEAM
(BRE Environmental
Assessment Method)
sets the standard for best
practice in sustainable
design and has become
the de facto measure
used to describe a
building’s environmental
performance.
The BREEAM Health and
Well Being credit HEA16
(drinking water) requires
chillers to be installed in
compliance with industry
standard.
ZG500 (right) enables
the Zip Chillmaster to fully
comply with these
requirements (see page
53).
Zip Water Block
HE45004
Recommended to be
fitted in the water supply
line to all Zip chilled
products (except
HydroTap) to minimise
the potential damage in
the event of leakage.
Hot water
Hot water
Zip offers one of the widest and most sophisticated
ranges available in the UK
Instantaneous
No standing heat loss, only heats water as required.
Unlimited supply of hot water - subject to conditions and demand.
Electronic temperature control automatically compensates for
fluctuations in incoming water temperature and pressure
Choose from:
ES; 3.1, 4.8 & 6.0kW (see pages 68-69)
ILX; 7.2, 9.6 & 13.5kW (see pages 72-73)
CEX; 6.6-8.8, selected at time of installation (see pages 74-75)
DEX & DBX 18, 21, 24 & 27kW (see pages 76-77)
Unvented
Fed directly from cold water mains
Quicker to install with no need for cold water storage cistern
Balanced hot and cold water supplies
High performance showering and faster filling baths
No special taps needed
Choose from:
Aquapoint, 5 to 100 litres (see pages 80-81 & 86-87)
Varipoint, 10 to 100 litres (see pages 82-83 & 88-89)
AquaFlo, 90 to 300 litres (see pages 90-93)
Open Vented
Easy to install
Single point of use
Overbasin and underbasin variants
Overbasin includes spout and valve
Underbasin requires vented taps
Choose from:
Tudor, 5 & 10 litres (see pages 94-95)
Contract, 5 & 10 litres (see pages 96-97)
Cistern Fed Storage
For installations where main fed systems are not an option
Can serve multiple outlets
Can be installed in ceiling voids
Reliable, ‘fit and forget’ solution
Choose from:
RCH, 25 to 100 litres (see pages 98-99)
64 65
Overview
Energy-efficient water heaters
Hot water
Hot water
Why Zip InLine instantaneous
water heating?
Zip InLine instantaneous water
heaters are the most energy
efficient way of directly heating
water electrically.
Using the very latest German
technology, Zip InLine offers a
host of Specifier, Installer and
End User benefits:
Unrivalled energy efficiency
No standing heat loss
Sophisticated electronic
control
Unlimited hot water supply
Easy to install
Compatible with standard
tapware
Neat compact design
Tangible water savings
Energy efficiency
Zip Inline saves energy by:
Heating only the water
drawn off
Avoiding stored water
heat losses
When comparing the energy
used over 24 hrs to deliver 75
litres of water at 38°C (assuming
12°C supply) typical savings of
23% can be achieved.
N.B. Percentage savings may be
less with increased demand but
more during periods without draw
off.
66 67
Zip InLine
instantaneous water heating
The inside story
Product Energy Usage
15 litre storage
water heater 3.0kWh
Zip InLine 2.3kWh
Traditional system Litres saved
pipe run per draw off
10 metres 3.2
*Subject to sufficient power being available to achieve the required
temperature and outlet flow under local conditions.
Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
Bare wire technology
The Zip ES, ILX012, DEX and
DBX models feature bare wire
heating technology using
stainless steel elements directly
immersed in the water flow
path.This system achieves
maximum efficiency by means of
direct contact with the water flow
plus the fastest possible heat up
times, typically less than 2
seconds.
Unlimited supply of hot water *
Zip InLine will deliver a continuous
supply at the selected temperature.
Easy installation
Zip InLine products simply connect
to standard closed outlet taps
without the need for unvented
water controls.
Smart design
The units compact size enables
it to fit neatly and unobtrusively in
any location.
Water conservation
Zip InLine is designed for
installation close to the point of
use, avoiding the need for water
to be run off before achieving
temperature.
Savings per draw off compared
to centralised systems with long
pipe runs are as follows:
Product Product Rating *3C Max Dimensions
Code kW @ 240V Flow Rate H x W x D
ltrs/min (mm)
Instantaneous
ES3 Zip Inline 3.1 1.7 132 x 187 x 80
ES4 Zip Inline 4.8 2.6 132 x 187 x 80
ES6 Zip Inline 6.0 3.3 132 x 187 x 80
*Maximum flow rate based upon incoming water temperature of 12°C.
Hot water
69
Zip Service/Technical Support 0800 077 8302
Zip Inline ES®
Electronic instantaneous
water heater
Single outlet for hand washing
Hot water
68 Customer Service 0845 602 4533
Features and benefits
Compact electronically controlled
instantaneous water heater for
hand washing.
Bare-wire for fast heat up.
Innovatively designed appliance
that heats the water automatically
as it flows through.
No standing heat losses.
Heating power automatically
adjusted to compensate for
variable inlet pressure and
temperature. Supplied with
700mm of pre-wired cable.
Intended for use with taps having
removable M22/M24 nozzles.
Easy to install with clip-on
mounting bracket.
Operation
Heating power is switched on
automatically once the minimum
flow rate is exceeded.
Rating
ES3 3.1kW @ 240V.
ES4 4.8kW @ 240V.
ES6 6.0kW @ 240V.
Heating system
Bare-wire heating system for fast
response.
Safety feature
Water temperature electronically
controlled to maintain factory
setting of 38°C.
IP rating
IP 24.
Product Selection
Instantaneous water heating is the
most efficient available, however,
delivered water temperature is
dependent on local incoming
water temperature and supply
voltage. Quoted performance
assumes 12°C incoming water
temperature and 240V supply.
Case
Impact resistant plastic.
Approvals
WRAS, VDE, CE endorsed.
Temperature setting
Temperature and flow adjustable
at time of installation.
Taps - Important
For correct operation it is
essential that the special tap
nozzle supplied is fitted to
the tap spout.
Nozzles supplied to suit
M22/24 taps should be used.
Warranty
One-year on site parts and
labour. For full details of the
Zip Warranty Scheme visit:
www.zipheaters.co.uk/warranty
Location
The appliance must be installed
in a frost free environment.
Plumbing
The appliance is intended for
connection to the mains water
supply. It should be installed by
a suitably qualified person. The
appliance may be used as an
unvented or vented installation.
N.B. Not recommended for use
with thermostatic mixing valves
or taps.
Electrical
The appliance must be earthed
and connected to the supply by
means of permanent wiring
through suitable isolation having
a contact separation of at least
3mm in all poles. Installation
must comply with current IEE
regulations.
Technical Data
Maximum temperature increase
@ 240V and a flow rate of: ES3 ES4 ES6
2.0 litres/min 22°C 34°C 43°C
2.5 litres/min 18°C 27°C 34°C
3.0 litres/min 15°C 23°C 29°C
3.5 litres/min 13°C 20°C 24°C
4.0 litres/min 11°C 17°C 21°C
Switch on flow rate (litres/min) 1.2 1.5 1.5
Switch off flow rate (litres/min) 1.0 1.3 1.3
71
Zip Service/Technical Support 0800 077 8302
70 Customer Service 0845 602 4533
Hot water
Hot water
Zip InLine ES®
Instantaneous hand wash packs –
complete with heater, tap & fittings
Isolating
valve
Flow rate
adjuster Non
return
valve
NC Pack (non-concussive tap)
MT Pack (mixer tap)
These new packs provide the installer with the ES
heater, compatible tap and a comprehensive
plumbing kit including flexible hoses and fittings to
ensure quick and easy system installation.
The packs are offered in a choice of 3 power ratings
with non-concussive or mixer tap.
Non-concussive (NC) pack:
ES instantaneous water heater
Non-concussive single outlet tap
50cm flexible hose for connection
to heater
50cm flexible hose for connection
to tap
(Isolating valve NOT supplied)
Mixer Tap (MT) pack:
ES instantaneous water heater
Single lever mixer tap complete
with braided hoses
50cm braided hose for connection
to heater
Flow rate adjuster for cold supply
Non-return valve for hot supply to tap
Tee piece connector
(Isolating valve NOT supplied)
Approvals
WRAS, VDE, CE endorsed
Product Tap Type Rating *3C Max Flow Rate
Code kW @ 240V ltrs/min
ES3/NC Non-concussive 3.1 1.7
ES4/NC Non-concussive 4.8 2.6
ES6/NC Non-concussive 6.0 3.3
ES3/MT Single lever mixer 3.1 1.7
ES4/MT Single lever mixer 4.8 2.6
ES6/MT Single lever mixer 6.0 3.3
ZL018 Matching non-concussive cold tap
Matching
cold tap
Isolating
valve
Hot water
73
Zip Service/Technical Support 0800 077 8302
Hot water
72 Customer Service 0845 602 4533
Zip Inline®ILX
Electronic instantaneous
water heater
Single outlet
Product Product Rating *45˚C Max *3C Max Dimensions
Code kW Flow Rate Flow Rate H x W x D
ltrs/min ltrs/min (mm)
instantaneous
ILX006 Zip Inline 7.2 @ 240V 3.0 4.0 330 x 210 x 110
ILX009 Zip Inline 9.6 @ 240V 4.0 5.2 330 x 210 x 110
ILX012 Zip Inline 13.5 @ 400V 5.7 7.4 330 x 210 x 110
*Maximum flow rate based upon incoming water temperature of 12°C.
Features and benefits
Provides instant hot water
without need for storage.
Gives a constant supply of
hot water at the set temperature.
Single Phase and Three Phase
options.
Operation
Heating power is switched on
automatically once the minimum
flow rate is exceeded.
‘Heater on’ indication.
Ratings
ILX 006 7.2kW @ 240V.
ILX 009 9.6kW @ 240V.
ILX 012 13.5kW @ 400V.
Heating system
Tubular element (7.2 & 9.6kW).
Bare-wire system (13.5kW).
Safety feature
Automatic power reduction to
avoid excessive temperatures
with visual indication.
Filter
Integral. Easy to clean, combined
fine filter and strainer with flow
rate adjustment valve.
IP rating
IP 25. May be used in zone 1.
Flow rate If
heating power is insufficient to
achieve the selected flow rate a
visual indication encourages
users to readjust.
Approvals
WRAS, CE endorsed.
Warranty
One-year on site parts and
labour. For full details of the
Zip Warranty Scheme visit:
www.zipheaters.co.uk/warranty
Temperature setting
Easily adjustable for required
temperature and electronically
controlled.
Location
The appliance must be installed
in a frost free environment.
To avoid distribution losses, the
distance between the heater and
the outlet should be as short as
possible (less than 2m).
For optimum flow
characteristics use with Zip
tap spray nozzles or hand sets.
Plumbing
12” BSP connections.
Minimum flow requirements:
2 litres/min.
Should be installed by a suitably
qualified person.
N.B. Not recommended for use
with thermostatic mixing valves
or taps.
Electrical
The appliance must be earthed
and connected to the supply by
means of permanent wiring
through suitable isolation having
a contact separation of at least
3mm in all poles. Installation
must comply with current IEE
regulations.
The cross sectional area of the
connection cable must be in
accordance with the power rating
of the appliance.
ILX012 requires three phase
electrical supply.
Technical Data
Maximum temperature increase
@ 240V and a flow rate of: ILX006 ILX009 ILX012
3.0 litres/min 34°C 46°C 55°C
4.0 litres/min 26°C 34°C 48°C
5.0 litres/min 21°C 27°C 38°C
6.0 litres/min 17°C 23°C 32°C
Factory set flow rate (litres/min) 3.5 4.5 5.0
Switch on flow rate (litres/min) 2.0 2.0 2.0
Switch off flow rate (litres/min) 1.8 1.8 1.8
Hot water
75
Zip Service/Technical Support 0800 077 8302
Hot water
74 Customer Service 0845 602 4533
Product 25˚C Max Temperature Power Dimensions
Code Flow Rate setting range Rating H x W x D
ltrs/min C) (kW @ 230V) (mm)
CEX 3.8 20-55 6.6/8.8* 330 x 210 x 110
* Selected at time of installation
Zip Inline®CEX NEW
Over and Undersink Electronic
Instantaneous Water Heaters for
Single or Multiple Outlets
Features and benefits
The most energy efficient way
of directly producing hot
water electrically.
Highly efficient bare wire
heating system.
Zero standing heat loss as no
stored water.
Instant hot water.
Provides a constant supply of
hot water at exactly the
temperature selected.
Heating power adjusted
electronically to compensates
for variable inlet pressures and
temperatures.
Required temperature can be
set using two touch sensitive
keys within the range 20°C to
55°C with digital display.
Maintains precise temperature
control despite fluctuations in
voltage and water pressure.
Suitable for use with
preheated water from solar
systems.
Power rating can be selected
at time of installation.
Optional wireless control
(ZL016).
CEX-O for oversink CEX-U
for undersink installation.
Ratings
6.6kW—8.8kW. Selected at
installation.
Heating System
Bare-wire system.
IP Rating
Oversink P25 Undersink IP24
Suitable for Zone 1.
Approvals
WRAS, VDE & CE endorsed.
Warranty
1 year on site parts and labour.
For full details visit:
www.zipheaters.co.uk/warranty
Location
The appliance must be installed
in a frost free environment.
In order to minimise thermal
losses the distance between the
appliance and the outlet fitting
should be as short as possible.
Plumbing
The appliance is intended for
connection to a mains potable
water supply. The specific water
resistance of the supply must not
fall below the minimum specified
on the rating plate.
Minimum flow rate 2 litres/min.
Should be installed by a suitable
qualified installer of electric
instantaneous water heaters.
Electrical
The appliance must be earthed
and connected to the supply by
means of permanent wiring
through an isolation switch
having a contact separation of at
least 3mm on all poles and
protected by a suitably rated
circuit breaker.
The cross sectional area of the
connection cable must be in
accordance with the poser rating
of the appliance.
The installation must be in
accordance with current IEE
regulations.
Hot water
77
Zip Service/Technical Support 0800 077 8302
Hot water
76 Customer Service 0845 602 4533
Product Power Max@ Max@ Max Dimensions
Code Rating t=28k t=38k Flow Rate H x W x D
(kW @ 3/PE (ltrs/min) (mm)
380-415V)
18 9.2(2) 6.8 8.0(3) 380 x 210 x 110
DEX 21 10.7(2) 7.9 8.0(3) 380 x 210 x 110
24 12.3(2) 9.0(2) 8.0(3) 380 x 210 x 110
27(1) 13.8(2) 10.2(2) 8.0(3) 380 x 210 x 110
DBX 18 18 9.2(2) 6.8 7.0(3) 380 x 210 x 110
DBX 21 21 10.7(2) 7.9 8.0(3) 380 x 210 x 110
DBX 24 24 12.3(2) 9.0(2) 8.0(3) 380 x 210 x 110
DBX 27 27(1) 13.8(2) 10.2(2) 9.0(3) 380 x 210 x 110
ZL017 Optional remote control for DEX
(1) Maximum 400V for DEX and DBX at 27kW.
(2) Mixed with cold water at the outlet.
(3) Flow rate limited to achieve optimum temperature rise.
Zip InLine®DEX & DBX NEW
Electronic Instantaneous
Water Heaters for Single or
Multiple Outlets
Features and benefits
All models
The most energy efficient way
of directly heating water
electrically.
Highly efficient bare wire
heating system.
Zero standing heat loss as no
stored water.
Instant hot water.
Provides a constant supply of
hot water at exactly the
temperature selected.
Heating power adjusted
electronically to compensate
for variable inlet pressures and
temperatures.
Maintains precise temperature
control despite fluctuations in
voltage and water pressure.
Optional remote control
temperature selection
(using ZL017)
DBX:
Outlet temperature set to 5C
adjustable inside the appliance
from 30°C to 60°C.
DEX:
If required, two temperature
settings can be set using the
touch sensitive keys within the
range 20°C to 60°C with
digital display.
Suitable for use with preheated
water from solar systems.
Power rating can be selected
at time of installation.
Ratings
DEX 18-27kW (adjustable)
DBX 18kW,21kW, 24kW & 27kW.
Heating System
Bare-wire system.
IP Rating IP
25 – Suitable for Zone 1.
Approvals
WRAS, VDE & CE endorsed.
Warranty
1 year on site parts and labour.
For full details visit:
www.zipheaters.co.uk/warranty
Location
The appliance must be installed
in a frost free environment.
In order to minimise distribution
losses the distance between the
appliance and the outlet fitting
should be as short as possible
(less than 2m).
Plumbing
The appliance is intended for
connection to a mains potable
water supply. The specific water
resistance of the supply must not
fall below the minimum specified
on the rating plate.
Minimum flow requirements:
2 litres/min.
Should be installed by a suitably
qualified person.
N.B. Not recommended for use
with thermostatic mixing valves
or taps.
Electrical
The appliance must be earthed
and connected to the supply by
means of permanent wiring
through an isolation switch
having a contact separation of at
least 3mm on all poles and
protected by a suitably rated
circuit breaker.
The cross sectional area of the
connection cable must be in
accordance with the power rating
of the appliance.
The installation must be in
accordance with current IEE
regulations.
Hot water
79
Zip Service/Technical Support 0800 077 8302
Zip InLine
instantaneous water heating
Instantaneous flow and
temperature rise chart
Hot water
78 Customer Service 0845 602 4533
Zip InLine
Accessories
Optimum performance
For the best results from the Zip InLine products the following tap
spray nozzles, handsets and remote control should be used.
110
126
65
60
55
50
45
40
35
30
4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.0 14.0
Flow Rate (l/min) mixed with cold water at the outlet
Delivered Temp (˚C) with 12˚C ambient
Touch-free taps for use with Zip InLine
Tap spray nozzle
Code Type Flow rates from
ZL002 22mm female thread 2.0 litres/min
ZL003 24mm male thread 2.0 litres/min
Tap aerator nozzle
Code Type Flow rates from
ZL008 15mm insert 3.5 litres/min
ZL004 22mm female thread 3.5 litres/min
ZL005 24mm male thread 3.5 litres/min
Shower hand set
Code Type Flow rates from
ZL006 Fixed pattern 4.0 litres/min
Shower hand set
Code Type Flow rates from
ZL007 4 mode adjustable 4.0 litres/min
60
55
50
45
40
35
30
25 0.0 1.0 2.0 3.0 4.0 5.0 6.0
Flow Rate (l/min)
Delivered Temp (˚C) with 12˚C ambient
ES3
ES4
ES6
ILX006
ILX009
Single Phase
Three Phase
ILX012
DEX/DBX (18kW)
DEX/DBX (21kW)
DEX/DBX (24kW)
DEX/DBX (27kW)
Standard reach
basin/sink tap
TF003—Mains powered
TF004—Battery powered
130
145 Long reach
basin/sink tap
TF001—Mains powered
TF002—Battery powered
Hot water
Hot water
80 81
Product Product Capacity Thermal Loss Dimensions
Code litres kWh/day H x W x D
(mm)
Oversink
AP3/05/OB Zip Aquapoint III 5 0.35 376 x 256 x 260
AP3/10/OB Zip Aquapoint III 10 0.48 480 x 350 x 265
AP3/15/OB Zip Aquapoint III 15 0.62 480 x 350 x 310
Undersink
AP3/05 Zip Aquapoint III 5 0.35 376 x 256 x 260
AP3/10 Zip Aquapoint III 10 0.48 480 x 350 x 265
AP3/15 Zip Aquapoint III 15 0.62 480 x 350 x 310
Zip Aquapoint III®
Unvented water heater
Single or multiple outlets
5, 10, 15 litre
Undersink and Oversink
Safety features
Manually resettable over
temperature safety cutout.
Expansion relief valve (supplied)
set at 6 bar.
Sacrificial anode for added
protection for element and tank
in aggressive water conditions,
requiring regular inspection and
replacement when necessary.
Installation
Separate models available for
oversink and undersink
installation.
All models can be wall mounted.
Undersink units can be installed
unsupported on the floor if
required.
All models can supply one outlet
or multiple outlets, subject to
capacity, without the need for
special taps.
Plumbing
Water connections 12” BSP
Expansion relief valve (supplied)
set at 6 bar. Should be installed
only by a suitably experienced
installer of unvented electric
storage water heaters.
Oversink and undersink models
not interchangeable.
Electrical
To be wired to a double pole
switched fused spur with a
minimum break capacity of 13
amps. Installation must comply
with current IEE regulations.
Supplied with 1 metre of
pre-wired cable.
Features and benefits
Glass lined steel inner container
tested to 12 bar.
Sacrificial anode for protection
against corrosion.
Element ‘ON’ neon indicator.
External temperature control
with frost protection.
Oversink and Undersink
versions available.
5, 10 & 15 litre.
Capacities
5 litre, 10 litre, 15 litre.
Rating
2.0 kW @ 230V.
Heating element
Embedded rod type.
Thermostat
Capillary type adjustable from
7ºC to 75ºC.
Water tank
1.8 mm glass enamelled steel
tested to 12 bar.
Case
High impact resistant white plastic.
Insulation
High density, CFC-free
polyurethane foam.
IP rating
24.
Approvals
WRAS, CE endorsed.
Warranty
One-year on site parts and
labour. For full details of the
Zip Warranty Scheme visit:
www.zipheaters.co.uk/warranty
Zip Service/Technical Support 0800 077 8302
Customer Service 0845 602 4533
Hot water
Hot water
82 83
Zip Varipoint II®
Unvented water heater
Single or multiple outlets
10, 15 litre
Undersink & oversink
Safety features
Manually resettable over
temperature safety cut-out.
Pressure and temperature relief
valve supplied.
Expansion relief valve supplied,
set at 6 bar.
Frost protection setting.
Installation
Separate models available for
oversink and undersink
installation.
All models can supply one or
more outlets.
No special taps required.
Undersink is floor standing or wall
hung on bracket (supplied).
Oversink is wall hung, on bracket
(supplied).
Plumbing
Water connections 12” BSP.
Pressure and temperature relief
valve (supplied) should be fitted
to heater.
Pressure relief valve (supplied)
to be fitted in cold water supply.
Should be installed only by a
suitably experienced installer of
unvented electric storage water
heaters.
Oversink and undersink models
not interchangeable.
Electrical
To be wired to a double pole
switched fused spur with a
minimum break capacity of 13
amps. Installation must comply
with current IEE regulations.
Supplied with 1 metre of
pre-wired cable.
Features and benefits
Heavy gauge copper inner
container tested to 16 bar.
Five year warranty on inner
container, two years on controls.
Does not require an anode or
regular inspection.
Supplied with temperature and
pressure relief valve.
Oversink and undersink
versions available.
10 litre or 15 litre.
External temperature control with
frost protection setting.
Element ‘ON’ neon indicator.
Supplied complete with wall
mounting bracket.
Capacities
10 litre, 15 litre.
Rating
2.2 kW @ 230V.
Heating element
Embedded rod type.
Thermostat
Capillary type adjustable up
to 75ºC.
Water tank
Heavy gauge copper, pressure
tested to 16 bar.
Case
High impact resistant white plastic.
Insulation
High density, CFC-free
polyurethane foam.
IP rating
24.
Approvals
WRAS, CE endorsed.
Warranty
Five year on site parts and labour
warranty on inner container, two
years on controls. For full details
of the Zip Warranty Scheme visit:
www.zipheaters.co.uk/warranty
Product Product Capacity Thermal Loss Dimensions
Code litres kWh/day H x W x D
(mm)
Oversink
VP103 Zip Varipoint II 10 0.36 452 x 300 x 285
VP153 Zip Varipoint II 15 0.50 452 x 300 x 285
Undersink
VP103UB Zip Varipoint II 10 0.41 452 x 300 x 285
VP153UB Zip Varipoint II 15 0.58 452 x 300 x 285
Zip Service/Technical Support 0800 077 8302
Customer Service 0845 602 4533
Hot Water
85
Zip Accessories
Unvented water heating
5, 10 & 15 litre capacity
Minimum length of pipe Length ‘X’
Capacity 15mm pipe 22mm pipe
5 litres 1.37m 0.6m
10 litres 2.7m 1.2m
15 litres 4.2m 1.8m
Diagram B
Inlet pressure less than 4 bar but expanded hot water cannot be ac-
commodated in the pipe work. (Install AQ2 expansion vessel and check
valve).
Diagram C
Inlet pressure greater than 4 bar. (Install AQ2 expansion vessel and check
valve with AQ3 pressure reducer).
Diagram D
Temperature and pressure relief valve AQ1.
Aquapoint
or Vari-
point
Aquapoint
or Vari-
point
Aquapoint
or Vari-
point
Aquapoint Varipoint
Diagram A
Inlet pressure less than 4 bar and expanded hot water can be accommodated
in the pipe work.
Zip Service/Technical Support 0800 077 8302
AQ2
Expansion
vessel and
check valve
(3.5 bar)
AQ3
Combined pres-
sure reducer (set
at 3.5 bar) and
line strainer
AQ1
Pressure and temperature relief valve (7 bar/90ºC).
Provides additional levels of safety when fitted to water
heater as shown in Diagram D.
Note: Varipoint supplied complete with AQ1.
Order AQ1 separately for use with Aquapoint.
AQ4 TMV2
Thermostatic blending valve complete with 2 check valves.
(Set temp range 30º to 65ºC).
AQ4S TMV3
NHS Approved Thermostatic Blending Valve complete with
2 check valves. (Set temp range 30º to 50ºC).
These blending valves provide over temperature protection
and are also ideal for extending system capacity.
Hot Water
Zip Accessories
Unvented water heating
5, 10 & 15 litre capacity
Varipoint & Aquapoint
Unvented Accessory Selection
Additional Accessories
84
YES
NO
NO
NO
NO
Will the pipework accommodate expanded water without hot water entering any supply
pipe connected to a cold water draw-off? (See diagram A opposite and note minimum
pipe lengths). If expansion in the cold water main is restricted, e.g. by a valve or meter,
an expansion vessel and other relevant accessories MUST be fitted.
Is reverse flow prevented, e.g. by a valve or meter?
Is the mains pressure 4.0 bar or less?
NOT REQUIRED
Fit AQ2 + AQ3
Is the mains pressure 4.0 bar or less?
Fit AQ2
Fit AQ2 + AQ3
Customer Service 0845 602 4533
AQ4
AQ1
YES
YES YES
Hot water
86
Hot water
87
Customer Service 0845 602 4533
Zip Aquapoint III®
Unvented water heater
Multiple outlet 30, 50, 80 & 100 litre
Approvals
WRAS, CE endorsed.
Safety features
Manually resettable safety cutout.
Heater protected against freezing
while power switched on.
Factory fitted pressure and
temperature relief valve designed
to operate at 7 bar and 90ºC.
Expansion relief valve set to
operate at 6 bar.
Installation
Wall mounted. Ensure wall is
strong enough to support water
heater when full.
Must be installed by a qualified
installer in accordance with Local
Regulations. England and Wales –
Building Regulations G3.
Scotland – Technical Standards P3.
N. Ireland – Building Regulations P5.
Plumbing
Water connections 12” BSP.
Minimum recommended water
pressure 1 bar.
Unit supplied with full installation
kit comprising: expansion vessel,
pressure reducing valve, balanced
take off valve, expansion relief
valve (6 bar), line strainer, tundish
and wall brackets.
Factory fitted P&T and expansion
relief valves require plumbing to
waste in accordance with water
authority bylaws.
Sacrificial anode for added
protection for element and inner
container in aggressive water
conditions – requires regular
inspection and replacement when
necessary.
Electrical
To be wired to a double pole
switched fused spur with a
minimum break capacity of 13
amps. Installation must comply
with current IEE regulations.
Element can be changed without
draining down.
Features and benefits
Glass lined steel inner container
tested to 13 bar.
Sacrificial anode for protection
against corrosion.
Element ‘ON’ neon indicator.
External temperature control with
frost protection.
High performance foam insulation.
Factory fitted P&T valve.
Element replacement can be
carried out without draining.
Accessories (supplied)
Pressure reducing valve and line
strainer set to 3.5 bar.
Expansion relief and single check
valve set to 6 bar.
Pressure and temperature relief
valve set to 7 bar and 90ºC.
External expansion vessel pre-
charged to 3.5 bar.
Tundish and wall brackets.
Capacities
30 litre, 50 litre, 80 litre, 100 litre.
Rating
3.0 kW @ 230V.
Heating element
Dry pocketed tubular.
Thermostat
Capillary type adjustable
20ºC to 75ºC.
Inner container
1.8mm glass enamelled steel
tested to 13 bar.
Case
Corrosion resistant white
enamelled steel.
Insulation
High density, CFC-free
polyurethane foam.
Warranty
One-year on site parts and
labour. For full details of the
Zip Warranty Scheme visit:
www.zipheaters.co.uk/warranty
Product Product Capacity Weight Thermal Dimensions
Code litres full (Kg) Loss H x W x D
kWh/day (mm)
AP3/30 Zip Aquapoint III 30 49 0.65 525 x 420 x 445
AP3/50 Zip Aquapoint III 50 74 0.68 690 x 420 x 445
AP3/80 Zip Aquapoint III 80 108 0.94 950 x 420 x 445
AP3/100 Zip Aquapoint III 100 131 1.1 1125 x 420 x 445
Zip Service/Technical Support 0800 077 8302
Hot water
89
Hot water
Zip Varipoint III®
Unvented water heater
Multiple outlets
30, 50, 80,100 litre
88 Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
Insulation
High density, CFC-free
polyurethane foam.
Approvals
WRAS, CE endorsed.
Warranty
Five-year on site parts and labour
warranty on inner container, two
years on controls. For full details
of the Zip Warranty Scheme visit:
www.zipheaters.co.uk/warranty
Safety features
Manually resettable safety cutout.
Heater protected against freezing
while power switched on.
Factory fitted pressure and
temperature relief valve designed
to operate at 7 bar and 90ºC.
Expansion relief valve set to
operate at 6 bar.
Installation
Wall mounted. Ensure wall and
fixings are strong enough to
support water heater when full.
Must be installed by a qualified
installer in accordance with Local
Regulations. England and Wales –
Building Regulations G3.
Scotland – Technical Standards P3.
N. Ireland – Building Regulations P5.
Plumbing
Water connections 12” BSP.
Minimum recommended water
pressure 1 bar.
Unit supplied with full installation
kit comprising: expansion vessel,
pressure reducing valve, balanced
take off valve, expansion relief
valve (6 bar), line strainer, tundish
and wall brackets.
P&T and expansion relief valves
require plumbing to waste in
accordance with water authority
bylaws.
Electrical
To be wired to a double pole
switched fused spur with a
minimum break capacity of 13
amps. Installation must comply
with current IEE regulations.
Features and benefits
Heavy gauge copper inner
container, tested to 12 bar.
Five year warranty on inner
container, two years on controls.
Does not require an anode or
regular inspection.
Supplied with factory fitted
P&T valve and full installation
fitting kit.
External temperature control.
Element ‘ON’ neon indicator.
High performance foam
insulation.
Accessories (supplied)
Pressure reducing valve set to
3.5 bar and line strainer.
Pressure relief valve set to 6 bar
and single check valve.
Pressure and temperature relief
valve set to 7 bar and 90ºC.
External expansion vessel pre-
charged to 3.5 bar.
Tundish and wall brackets.
Tee piece and drain valve.
Expansion vessel capacity
VP303/VP505 = 5 litre
VP803/VP953 = 8 litre
Capacities
30 litre, 50 litre, 80 litre, 100 litre.
Rating
2.7 kW @ 230V.
Heating element
Replaceable embedded rod type.
Thermostat
Capillary type adjustable
37ºC to 75ºC.
Inner container
Heavy gauge copper tested to
12 bar.
Case
Corrosion resistant white
enamelled steel.
Product Product Capacity Weight Thermal Dimensions
Code litres full (kg) Loss H x Dia
kWh/day (mm)
VP303 Zip Varipoint III 30 50 0.732 620 x 430
VP503 Zip Varipoint III 50 70 0.912 808 x 430
VP803 Zip Varipoint III 80 107 1.032 946 x 485
VP953 Zip Varipoint III 100 133 1.207 1091 x 485
Zip AquaFlo II®
Unvented water heater
Unvented stainless-steel cylinders
90 to 300 litre capacity
Construction
Direct, indirect and solar
compatible unvented water
heaters
Corrosion resistant Duplex
Stainless Steel cylinder
High performance, low profile
coil-in-coil heat exchanger
High performance CFC free
injected polyurethane foam
insulation
White plastic coated steel case
resistant to scuffs and damage
External expansion for reliability
and ease of maintenance
Cylinder pressure tested to 15
bar
Installation
For installation by a qualified
installer in accordance with all
national and local Building
Regulations.
Intended for floor standing
only – refer to Technical Data for
weight when full.
Nominal Capacity
Direct and Indirect units:
90, 120, 150, 180, 210, 250 and
300 litres.
Solar Twin Coil and Solar Direct
units: 150, 180, 210, 250 and
300 litres.
Immersion Elements
Incoloy construction 1¾” thread.
Length 14” Loading 3kW @
240V.
Heat Exchanger
22mm low profile, high efficiency
stainless steel coil-in-coil.
Features and benefits
Wide range of capacities from 90
litres up to 300 litres
High grade Duplex Stainless Steel
Unvented Cylinder for long life
Incoloy immersion elements
provide excellent corrosion
resistance
Compact coil-in-coil heat
exchangers provide fast heat up
and recovery
Multi-element options for faster
heat up
High performance insulation
ensures minimum heat loss
External expansion for optimum
reliability, more usable space and
ease of maintenance
No sacrificial anode. Avoids the
need for regular inspection
22mm compression connections
for ease of installation
Cylinders tested to 15 bar
25 year transferable cylinder
warranty
2 year warranty on all other
components
Fully approved to UK Water
Regulations and Buildings
Regulations Part G3 and Part L
90 91
Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
Controls
Thermostat – adjustable up to
65°C.
Over temperature safety cut-out
– Re-settable. Operates at 85°C.
Expansion relief valve – 6 bar.
Temperature and pressure relief
valve – 90°C and 7 bar.
Tundish.
Two way valve with indirect
models.
Pressure reducing valve – 3 bar.
Expansion vessel – Pre-charged
to 3 bar.
Plumbing
For connection to 22mm mains
potable water supply.
Minimum water supply 1.5 bar,
20 l/min.
Maximum water supply pressure
12 bar.
Electrical
To be wired to a suitably rated
double pole fused spur.
Installation must comply with
current IEE regulations.
Approvals
KIWA approved to UK Water
Regulations.
KIWA approved to UK Building
Regulations Part G3 and Part L.
Immersion element/thermostat
BEAB approved and CE
endorsed.
Warranty
25 years on cylinder transferable
(conditions apply).
2 years on all other components.
Hot water
Hot water
Zip AquaFlo II®
Unvented water heater
Unvented stainless-steel cylinders
90 to 300 litre capacity
92 93
Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
Hot water
Hot water
AquaFlo Direct
Product Nominal Height Weight Weight Vol within Heat up Heat up Heat up Boost Low level High level Standing
Code Capacity (mm) x Empty when Full 10ºC of set 3kW 6kW 9kW re-heat immersion immersion Loss
(L) 545 Dia (kg) (kg) temp (L) (mins) (mins) (mins) (mins) elements elements (kWh/day)
AF3090 90 727 21 111 73 76.0 - - - 1 0 1.07
AF3120 120 915 26 146 102 103.0 - - 58.0 1 1 1.23
AF3150 150 1102 33 183 133 134.0 - - 72.0 1 1 1.41
AF3180 180 1290 38 218 163 164.0 - - 82.0 1 1 1.53
AF3210 210 1478 41 251 194 203.0 - - 96.0 1 1 1.80
AF3250 250 1728 46 296 236 248.0 - - 117.0 1 1 2.15
AF3300 300 2041 55 355 288 323.0 - - 145.0 1 1 2.28
AF3150S* 150 1102 33 183 133 134.0 73 57 72.0# 3 or 2 0 or 1 1.41
AF3180S* 180 1290 38 218 163 164.0 88 67 82.0# 3 or 2 0 or 1 1.53
AF3210S* 210 1478 41 251 194 203.0 108 80 96.0# 3 or 2 0 or 1 1.80
AF3250S* 250 1728 46 296 236 248.0 130 95 117.0# 3 or 2 0 or 1 2.15
AF3300S* 300 2041 55 355 288 323.0 168 120 145.0# 3 or 2 0 or 1 2.28
* Supplied with 3 elements and 4 bosses - 3 at low level and 1 at high level. Additional elements are available for installation in the 4th boss. # If using high level element
AquaFlo Indirect
Product Nominal Height Weight Weight Vol within Indirect Heat Recovery Boost Low level High level Standing
Code Capacity (mm) x Empty when Full 10ºC of set Exchanger Indirect re-heat immersion immersion Loss
(L) 545 Dia (kg) (kg) temp (L) (kW) (mins) (mins) elements elements (kWh/day)
AF4090 90 727 23 111 74 16.46 12.0 - 1 0 1.07
AF4120 120 915 30 148 105 16.46 16.0 - 1 0 1.23
AF4150 150 1102 38 186 132 18.55 17.2 - 1 0 1.41
AF4180 180 1290 42 220 160 18.55 20.4 - 1 0 1.53
AF4210 210 1478 45 253 188 18.55 22.0 - 1 0 1.80
AF4250 250 1728 51 299 232 22.00 25.0 117.0 1 1 2.15
AF4300 300 2041 60 357 285 22.00 34.0 145.0 1 1 2.28
AquaFlo Solar Compatible
Product Nominal Height Weight Weight Vol within Indirect Heat Solar Dedicated Recovery Boost Low level High level Standing
Code Capacity (mm) x Empty when Full 10ºC of set Exchanger Heat Solar solar re-heat immersion immersion Loss
(L) 545 Dia (kg) (kg) temp (L) (kW) Exchanger Capacity (mins) (mins) elements elements (kWh/day)
Solar Twin Coil
AF5150 150 1102 40 187 132 18.55 16.46 77 25.0* 12.0# 0 1 1.41
AF5180 180 1290 45 222 160 18.55 18.55 95 26.3* 14.8# 0 1 1.53
AF5210 210 1478 48 255 188 22 18.55 101 31.2* 15.5# 0 1 1.80
AF5250 250 1728 53 300 232 22 22.00 107 33.0* 20.0# 0 1 2.15
AF5300 300 2041 63 359 285 22 22.00 121 41.0* 25.0# 0 1 2.28
Solar Direct
AF6150 150 1102 38 186 102 - 16.46 80 25.0* 72.0 1 1 1.41
AF6180 180 1290 42 220 123 - 18.55 100 26.3* 82.0 1 1 1.53
AF6210 210 1478 45 253 143 - 18.55 116 31.2* 96.0 1 1 1.80
AF6250 250 1728 51 299 175 - 22.00 137 33.0* 117.0 1 1 2.15
AF6300 300 2041 60 358 210 - 22.00 160 41.0* 145.0 1 1 2.28
Actual performance when installed will vary considerably dependant * Re-heat times based on BS12897 parameters with an 80°C primary flow at 15 l/min.
on the rate of solar or other renewable input, number of panels etc. # Using Indirect heat exchanger
Hot water
94
Hot water
95
Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
Zip Tudor®
Over-sink or under-sink water
heater
Open outlet for single point of use
5, 10 litre
Warranty
One-year on site parts and
labour. For full details of the
Zip Warranty Scheme visit:
www.zipheaters.co.uk/warranty
Operation
Externally adjustable temperature
control.
Neon light indicates when the
heating element is ‘ON’.
Safety features
Open-outlet non-pressurised
system.
Heater protected against freezing
while power switched on.
Manually re-settable over-
temperature safety cut-out.
Installation
Supplies hot water to a single
outlet using spout or Zip vented
taps. No need for expansion
vessel or pressure relief valve.
Screws and wall fixings provided.
Plumbing
Can be connected to a rising main
or to a cistern with a minimum
working head of 5 metres.
Over-sink models are supplied
with a 300mm open outlet spout
and control valve.
Undersink models must only be
connected to Zip open-outlet
taps, (see page 94).
Over-sink and under-sink models
are NOT interchangeable.
Electrical
To be wired to a double pole
switched fused spur with a
minimum break capacity of 13
amps. Installation must comply
with current IEE regulations.
Supplied with 1 metre of pre-
wired cable.
Features and benefits
Open outlet heater, for single
point of use.
Externally adjustable temperature
control with frost protection.
Manually re-settable cutout.
Oversink models supplied
complete with spout and valve.
Undersink models for connection
to Zip open-outlet tapware only -
(see page 94).
Supplied with 1 metre of
pre-wired cable.
CFC-free insulation.
Impact resistant, easy clean,
white plastic casing.
Neon power-on indicator light.
Choice of 5 and 10 litre capacity.
Supplied complete with wall
plugs and screws.
Capacities
5 litre, 10 litre.
Rating
1.8 kW @ 230V.
Heating element
Embedded rod type.
Thermostat
Capillary type, adjustable
35˚C to 80˚C.
Inner container
Polypropylene tested to 1.5 bar.
Case
Impact resistant plastic.
Insulation
Moulded CFC-free polystyrene.
Approvals
WRAS, CE endorsed.
Product Product Capacity Thermal Dimensions
Code litres Loss H x W x D
kWh/day (mm)
Oversink
P4/52 Zip Tudor 5 0.32 390 x 255 x 215
P4/102 Zip Tudor 10 0.40 440 x 310 x 265
Undersink
P4/52UB Zip Tudor 5 0.32 390 x 255 x 215
P4/102UB Zip Tudor 10 0.40 440 x 310 x 265
For compatible taps see page 94
5 litre model
10 litre model
Hot water
97
Hot water
96
Zip Contract®
Over-sink water heater
Open outlet for single point of use
5, 10 litre
Insulation
Moulded, CFC-free,
Polystyrene foam.
Approvals
WRAS, CE endorsed.
Warranty
One-year on site parts and
labour. For full details of the Zip
Warranty Scheme visit:
www.zipheaters.co.uk/warranty
Safety features
Safety cut out in the event of
a thermostat failure.
Heater protected against freezing
while power switched on.
Installation
All models should be wall mounted.
Screws and wall fixings provided.
Plumbing
Can be connected to a rising main
or to a cistern with a minimum
working head of 5 metres.
Supplied with a 300mm open outlet
spout and water control valve.
Electrical
To be wired to a double pole
switched fused spur with a
minimum break capacity of 13
amps. Installation must comply
with current IEE regulations.
Supplied with 1 metre of cable.
Features and benefits
Open outlet oversink water
heater for single point of use.
External temperature control with
frost protection.
Over temperature safety thermal
fuse (C2/50 and C2/100).
Remotely resettable over
temperature protection (C3/50).
Supplied with inlet control valve
and swivel outlet spout.
Impact resistant, easy clean,
white plastic casing.
CFC-free insulation.
Choice of 5 or 10 litre capacity.
Capacities
5 litre, 10 litre.
Rating
1.8 kW @ 230V.
Heating element
Embedded rod type.
Thermostat
Capillary type adjustable
35˚C – 80˚C.
Inner container
Polypropylene tested to 1.5 bar.
Case
Impact resistant white plastic.
Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
*UB6
Single lever
basin tap
*UB1
Monobloc
mixer
TS1
Telescopic spout
300-600mm
*UB7
Single lever
sink tap
Product Product Capacity Thermal Dimensions
Code litres Loss H x W x D
kWh/day (mm)
C2/50 Zip Contract 5 0.32 390 x 255 x 215
C2/100 Zip Contract 10 0.40 440 x 310 x 265
*C3/50 Zip Contract 5 0.32 390 x 255 x 215
*For use with Zip Tudor P4/52UB and P4/102UB
10 litre model
5 litre model
* Specialist product for temporary site applications with remotely resettable dry start
protection. For details contact Zip Technical support.
Zip Accessories
Vented Point of Use
Hot water
99
Hot water
98
Zip RCH®
Cistern-type water heater
Single or multiple outlet
25, 50, 75, 100 litre
Installation
Should be mounted on a wall at
least one metre above the
highest draw-off point.
Wall and fixings should be
adequate to support the weight
of the heater when full.
Heater to be fixed using the
integral wall mounting bracket.
Top clearance of 150mm must be
allowed for access to the ball
valve in the cistern tank.
Bottom clearance of 250mm
must be allowed for withdrawal
of the heating element.
Plumbing
Cold inlet, left or right hand
connection, 12” BSP.
Hot outlet, from base of heater,
22mm compression fitting.
Drain connection, supplied
and fitted.
Overflow, left or right hand
connection, 22mm compression
fitting.
Ball valve is for mains pressure
operation, brass body to BS1212-2.
Electrical
To be wired to a double pole
switched fused spur with a
minimum break capacity of 13
amps.
RCH 100/6 should be provided
with its own dedicated supply.
Installation must comply with
current IEE regulations. Supplied
with 1 metre of cable.
The cross sectional area of the
connection cable must be in
accordance with the power rating
of the appliance.
Features and benefits
Patented design ensures the
temperature of the water in the
cistern tank is maintained within
current regulatory limits.
The Zip RCH is the only UK water
heater of its type that is fully WRAS
approved.
Simple to install and maintain.
Trouble free operation.
Choice of 4 capacities.
Capacities
25 litre, 50 litre, 75 litre, 100 litre.
Rating
2.8 kW @ 230V
(5.6 kW option on 100 litre).
Heating element
Embedded rod.
Thermostat
Rod type, adjustable from
5ºC – 65ºC.
Water tank
Hot water tank and cold water
feed cistern are both manufactured
from copper sheet with brazed
seams.
Case
Corrosion resistant, white
powder coated steel.
Insulation
Fully fire-retardant foiled urethane
core.
Safety features
Over temperature cut-out.
Approvals
WRAS, CE endorsed.
Warranty
One-year on site parts and
labour. For full details of the
Zip Warranty Scheme visit:
www.zipheaters.co.uk/warranty
Customer Service 0845 602 4533 Zip Service/Technical Support 0800 077 8302
Product Product Rating Capacity Weight Dimensions
Code kW litres full H x W x D
@ 230V (kg) (mm)
RCH25 Zip RCH 3 25 53 705 x 470 x 210
RCH50 Zip RCH 3 50 106 750 x 600 x 320
RCH75 Zip RCH 3 75 136 925 x 600 x 320
RCH100 Zip RCH 3 100 164 1080 x 600 x 320
RCH100/6 Zip RCH 6 100 164 1080 x 600 x 320
Rear View SideView
Zip Hot Water
General Data
Useful formulae
Time to heat stored water (mins) =Litres x Temp Rise C)
kW rating x 14.3
Temperature rise with an =14.3 x kW rating
instantaneous water heater (˚C) Litres/min flow
Temperature Degrees Celsius = ( ˚F-32 ) x 59
Degrees Fahrenheit = ( ˚C x 95) + 32
Degrees Kelvin = ( ˚C + 273.2 )
Conversion factors
Pressure 1 Bar = 14.5 psi
= 100 kiloNewtons/m2= 100 kPa
1 psi = 7 kPa
Heat 1 kiloCalorie (kCal) is the amount of energy required
to raise 1 kg of water through one degree Celsius
General Data
100
General Data
101
Zip Hot Water
Typical applications
Application Suggested Page
(Up to) Zip Products reference
Single hand wash ES3, ES4, ES6 68
1 basin AP3/05, AP3/05/OB 78
P4/52, P4/52UB 92
C2/50 94
ILX006 72
CEX 74
1 sink P4/102, P4/102UB 92
C2/100 94
VP103, VP103UB 80
AP3/10, AP3/10/OB 78
ILX009 72
CEX 74
2 basins VP103, VP103UB 80
AP3/10, AP3/10/OB 78
ILX009 72
CEX 74
3 basins VP153, VP153UB 80
AP3/15, AP3/15/OB 78
1 basin, 2 sinks RCH25 96
3 basins, heavy use or 2 sinks VP303 86
AP3/30 84
DEX 76
5 basins, heavy use or 3 sinks VP503 86
AP3/50 84
RCH50 96
1 shower ILX012 72
DEX 76
1 bath & shower VP803 86
AP3/80 84
RCH75 96
DEX 76
Bed-sit AF3120, AF4090 88
VP953 86
AP3/100 84
RCH100 96
DEX/DBX 76
1 bath & shower (1-2 beds) AF3150, AF4120 88
DEX 76
1 bath & shower (3 beds) AF3180, AF4150 88
1 bath & shower (4 beds) AF3210, AF4180 88
2 bath & shower (5 beds) AF3250, AF4210 88
3 bath & shower (6 beds) AF3300, AF4250 88
Zip Heaters (UK) Ltd reserves the right to modify the specification of
its products without notice and makes every effort to maintain the
accuracy of information contained in this publication.
The terms ‘Zip’, ‘HydroTap’, ‘Hydroboil’, ‘Econoboil’, ‘Duo’, ‘Chilltap’,
‘Chillmaster’, ‘Wall Fountain’, ‘Chill Fountain’, ‘Aquapoint’, ‘Varipoint’,
‘AquaFlo’, ‘Inline ES’, ‘InLine’, ‘Tudor’, Contract’ and ‘RCH’ are all reg-
istered trademarks.
The Zip Guide Summer 2011 – © Copyright Zip Heaters (UK) Ltd
102 103
Notes Notes
Zip Heaters (UK)Ltd
Bertie Ward Way, Dereham, Norfolk NR19 1TE
London Office:
Clover House, 147-149 Farringdon Road,
Clerkenwell, London EC1R 3HN
sales@zipheaters.co.uk
Sales enquiries Tel: 0845 602 4533
customerservice@zipheaters.co.uk
Zip Service/Technical Support Tel: 0800 077 8302
service@zipheaters.co.uk
Fax: 01362 692448
www.zipheaters.co.uk

Navigation menu