High Resolution Indoor/Outdoor IR Color CCTV Bullet Camera User Manual Security Bc601 Series Nb
User Manual: Security Camera
Open the PDF directly: View PDF 
.
Page Count: 16
| Download | |
| Open PDF In Browser | View PDF |
High Resolution Indoor/Outdoor IR Color CCTV Bullet Camera User Manual Products: BC600 Series, BC601 Series, BC700 Series Cameras BC600 Camera BC700VF Camera BC700VFE Camera Please read this manual before using your camera, and always follow the instructions for safety and proper use. Save this manual for future reference. BC600-BC601-BC700_CM 11/7/2013 ! WARNING CAUTION Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the camera. To prevent electric shock and risk of fire hazards, do NOT use other than the specified power source. REGULATORY NOTICE These cameras comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and use in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference, in which case the user will be required to correct the interference at his own expense. These cameras are CE and RoHS compliant. LEGAL NOTICE Observint Technologies (Observint) products are designed to meet safety and performance standards with the use of specific Observint authorized accessories. Observint disclaims liability associated with the use of non-Observint authorized accessories. The recording, transmission, or broadcast of any person’s voice without their consent or a court order is strictly prohibited by law. Observint makes no representations concerning the legality of certain product applications such as the making, transmission, or recording of video and/or audio signals of others without their knowledge and/or consent. We encourage you to check and comply with all applicable local, state, and federal laws and regulations before engaging in any form of surveillance or any transmission of radio frequencies. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Observint disclaims any proprietary interest in trademarks and trade names other than its own. No part of this document may be reproduced or distributed in any form or by any means without the express written permission of Observint © 2013 Observint Technologies. All Rights Reserved. 11000 N. Mopac Expressway, Building 300, Austin, TX 78759 For Sales and Support, please contact your distributor. ii Table of Contents SECTION 1 SECTION 2 SECTION 3 SECTION 4 APPENDIX A Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 What’s in the box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.2 Tools you need. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.1 General Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.2 Mounting the camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 2.3 Camera adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.4 OSD Setup (BC700 series cameras only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 High Resolution Indoor/Outdoor IR CCTV Bullet Camera User Manual iii Precautions • • • • • • This camera should be installed by qualified personnel only. There are no user serviceable parts inside. Do not disassemble this camera other than to make initial adjustments. Use a UL approved regulated 12 volt DC power supply. Use appropriate low voltage power cable to prevent fire or electrical shock. Please insure that your installation area can support the weight of the camera. Handle this camera carefully • • • • • • • • • • • • • iv Do not use a strong or abrasive detergent when cleaning the camera. Do not install near cooling or heating devices. Do not install the camera in extreme temperature conditions. Use the camera in environments where temperature is within 14°F to 122°F. Use adequate ventilation if a camera is installed where high temperatures may occur. Do not install or use the camera in an environment where the humidity is high. Very high humidity levels can reduce image quality. Do not install the camera under unstable lighting conditions. Severe lighting change or flicker can cause the camera to work improperly. Do not touch the front lens of the camera. Finger prints, dust and soil on the front glass can cloud the video image and reduce the effectiveness of the IR array. Do not drop the camera or subject it to physical shocks. Do not expose the camera to rain or spill liquids on it. If it gets wet, wipe dry immediately. Liquids can contain minerals that corrode the electronic components. Do not expose the camera to radioactivity. If exposed to radioactivity the video sensor may fail. Do not disassemble the camera. There are no user-serviceable parts inside it. Do not drop the camera or subject them to physical shocks. It can cause malfunctions to occur. Never point the camera at a strong light, or exposing it to a spotlight or an object reflecting the strong light. Smear or blooming may occur, and it can damage the CCD. Before applying power to the camera, check the power source to ensure that it is within specifications. SECTION 1: INTRODUCTION SECTION 1 Introduction Features • • • High resolution color sensor: 600 TV Lines (BC600, BC601 series), 700 TV Lines (BC700 series) OSD control functions (BC700 seriess) 12 Vdc power Integrated Mounting Bracket CDS Sensor Vari-focal Lens (2.8 mm - 12 mm) ( -VF, -VFE cameras only) IR LED Array BC700VFE Camera High Resolution Indoor/Outdoor IR CCTV Bullet Camera User Manual 1 SECTION 1: INTRODUCTION Base Sun shield Hold Down Screw Mounting Bracket Adjustment Screws BC600, BC601, BC700 Series Cameras Side View OSD Controller (BC700 Series Only) Power Input (12 Vdc) Cable Channel Video Output BC700VF Camera Top View 2 SECTION 1: INTRODUCTION Focus, Zoom Adjusters (vari-focal ( -VF, -VFE) cameras only) Product Label BC700VFE Camera Bottom 1.1 What’s in the box Your camera includes the following: • • • • Camera assembly Hex wrench Mounting hardware This manual 1.2 Tools you need To install the camera, you will need: • • • • 12 Vdc power source. See Specifications for current requirement. Tools and additional fasteners (may be required) for mounting the camera Video and power extension cable CCTV video setup monitor (optional) High Resolution Indoor/Outdoor IR CCTV Bullet Camera User Manual 3 SECTION 2: INSTALLATION SECTION 2 Installation 2.1 General Guidelines • Camera Lens: Handle the camera carefully to prevent scratching or soiling the lens. If the lens or IR array shield becomes soiled, clean it only with approved products. See the Cleaning section later in this manual. • Monitor impedance: Set the monitor impedance switch to 75 Ω. • Power supply: To avoid fire or shock hazard, use only UL listed power supplies. • Camera drop cable: The camera drop cable includes two connectors: —— Video BNC connector – for transmission of the video signal across a coax (75 Ω) extension cable. —— Power connector – Use 12 Vac power source (see the Specifications section for power requirements). When applying 12 Vdc power, observe the power polarity. See the picture below for the connector polarity configuration. Video BNC Connector Power Connector Camera Drop Cable 2.2 Mounting the camera The camera can be mounted on any surface with sufficient strength to support it. The video/power drop cable from the camera can be routed either through the cable hole in the center of the base plate, or through a cable guide in the mounting bracket. 1. 4 Using the camera base as a guide, mark the location of the screws that anchor the base plate to the mounting surface. If you are routing the drop cable through base, also mark the position of the hole for the drop cable. SECTION 2: INSTALLATION NOTE Position the base plate so that the cable guide in the mounting bracket is pointing away from any source of water, dust, and other contaminates. 2. Drill holes for the screws that anchor the base to the mounting surface. The mounting hardware provided is appropriate for most surfaces. However, depending on the surface materials, more appropriate fasteners may be required. 3. Drill a 3/4" hole for the drop cable, if necessary. 4. Route the drop cable through the hole through the base plate, or through the cable guide in the mounting bracket, then attach the camera assembly to the surface using the appropriate fasteners. 5. Connect the camera drop cable to video and power extension cables as required. NOTE Drop cable connectors are not waterproof. 2.3 Camera adjustments 1. Apply power to the camera. 2. If using a CCTV video system monitor to setup your camera, connect the video output of the camera to your CCTV monitor. 3. Verify that video from the camera can be seen on the monitor. 4. While observing video from the camera, use the hex wrench provided to loosen the two mounting bracket adjustment screws. 5. Point the camera at the center of your surveillance target, then tighten the bracket adjustment screws. High Resolution Indoor/Outdoor IR CCTV Bullet Camera User Manual 5 SECTION 2: INSTALLATION Sun Shield Hold Down Screw Use for Horizon Line Adjustment Use for Direction, Elevation Adjustment 90° 360° 6. Adjust the sun shield (forward or back) to reduce glare, if necessary. 7. If your camera has a varifocal lens ( -VF or -VFE models), use the hex wrench provided to adjust the video zoom and focus. The adjustment screws are located on the bottom of the camera. 8. If your camera is a BC700 series model, configure your camera using the software menus in the OSD. See OSD Setup in the following subsection. 2.4 OSD Setup (BC700 series cameras only) BC700 series cameras include on-screen display (OSD) software for adjusting the internal camera settings to complement specific environment where it is installed. These settings are adjusted using the OSD controller attached to the camera drop cable. The OSD controller includes a joystick that can be pushed down and rocked UP, DOWN, left (L) and right (R), or, to open the menu system and navigate the menus. To use the OSD controller, press the joy stick in (toward the controller block) to open the OSD menu. (See the menu chart on the following page.) Rock the joystick UP or DOWN to highlight a parameter or submenu, then press the joystick in to select it. Rock the joystick right (R) to highlight an option, UP or DOWN to identify the option, then press the joystick in to select it. Repeat this method to navigate the menu system and select options. 6 Joystick OSD Controller SECTION 2: INSTALLATION OSD MENU OPTIONS MANUAL LENS AUTO TYPE: DC / VIDEO MODE: CLOSE / AUTO/OPEN SPEED: 0-255 HIGH LUMINANCE MODE: SHUT+AUTO IRIS / AUTO IRIS AUTO SHUTTER/ AGC BRIGHTNESS: 0-255 LOW LUMINANCE MODE: OFF / AGC BRIGHTNESS: ×0.25, ×0.5, ×0.75, ×1 MODE: SHUT+AGC MANUAL SHUTTER: 1/50, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 s AGC: 6, 12, 18, 24, 30, 36, 42, 44.8 WHITE BAL OSD SET ATW SPEED / DELAY CNT / ATW FRAME / ENVIRONMENT PUSH / ANTI CR / PUSH LOCK / USER1 / USER2 / MANUAL BACK LIGHT OFF / BLC / HLC PICT ADJUST MIRROR / BRIGHTNESS / CONTRAST / SHARPNESS / HUE / GAIN ATR MOTION DET PRIVACY DAY/NIGHT OFF -- ON LUMINANCE/CONTRAST OFF -- ON DETECT SENSE / BLOCK DISP / MONITOR AREA / AREA SEL / TOP / BOTTOM / LEFT / RIGHT OFF -- ON AREA SEL / TOP / BOTTOM / LEFT / RIGHT / COLOR / TRANSP / MOSAIC COLOR -- B/W BURST: OFF / ON AUTO BURST: OFF / ON DELAY CNT / DAY-NIGHT / NIGHT-DAY NR NR MODE: Y/C, OFF, Y, C CAMERA ID OFF/ON -- SYNC INT -- LANGUAGE ENGLISH / CHINESE / JAPANESE / ESPANOL / PORTUGUESE / PYCCKNN / FRANCAIS / DEUISCH CAMERA RESET / BACK / EXIT / SAVE ALL High Resolution Indoor/Outdoor IR CCTV Bullet Camera User Manual 7 SECTION 3: CLEANING SECTION 3 Cleaning Clean the camera dome with an approved glass cleaning solution and a lint free cloth. • • Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub the surface with a soft cloth moistened with a mild detergent solution, then rinse and dry it with a soft cloth. Remove all foreign particles, such as plastic or rubber materials, attached to the camera housing. These may cause damage to the surface over time. CAUTION 8 Do not use benzene, thinner or other chemical products on the camera assembly; these may dissolve the paint and promote damage of the surfaces. Before using any chemical product, read the accompanying instructions carefully. SECTION 4: SPECIFICATIONS SECTION 4 Specifications Table 1. Specifications for BC600 series, BC601 series cameras Model BC600 BC601 BC601VF BC601VFE Sensor 1/3" CMOS 1/3" SHARP 1/3" SHARP 1/3" SHARP Effective Picture Elements (H x V) 728 (H) x 488 (V) 768 (H) x 494 (V) 768 (H) x 494 (V) 768 (H) ) x 494 (V) Horizontal Resolution 600 TV Line 600 TV Line 600 TV Line 600 TV Line Minimum Illumination 0.1 lux / F1.2 0.01 lux / F1.2 0.01 lux F1.2 / 0 lux (with IR LED ON) 0.01 lux F1.2 / 0 lux (with IR LED on) S/N Ratio More than 46 dB More than 48 dB More than 48 dB More than 48 dB Scanning System 2:1 interface 2:1 interface 2:1 interface 2:1 interface Synchronous System Internal, negative sync. Internal, negative sync. Internal, negative sync. Internal, negative sync. Auto Electronic Shutter 1/60 s ~ 1/100,000 s 1/60 s ~ 1/100,000 s 1/60 s ~ 1/100,000 s 1/60 s ~ 1/100,000 s Gamma Characteristic 0.45 0.45 0.45 0.45 IR Distance 65 ft (with Ø5 x 24 PCS Infrared LEDs) 65 ft (with Ø5 x 24 PCS Infrared LEDs) 131 ft (with Ø5 x 42 PCS Infrared LEDs) 196 ft (with Ø5 x 72 PCS Infrared LEDs) IR Status Under 10 lux by CDS Under 10 lux by CDS Under 10 lux by CDS Under 10 lux by CDS IR Power On CDS AUTO control CDS AUTO control CDS AUTO control CDS AUTO control Video Output 1 Vp-p, 75 Ω 1 Vp-p, 75 Ω 1 Vp-p, 75 Ω 1 Vp-p, 75 Ω Auto Gain Control Auto Auto Auto Auto Power/Current 12 Vdc (+/-10%) / 350 mA 12 Vdc (+/-10%) / 350 mA 12 Vdc (+/-10%) / 500 mA 12 Vdc (+/-10%) / 800 mA Lens 3.6 mm / F2.0 3.6 mm / F2.0 2.8 - 12 mm manual zoom 2.8 - 12 mm manual zoom Dimensions (w x h x d) 6.89 x 2.72 x 2.17 in (175 x 69 x 55 mm) 6.89 x 2.72 x 2.17 in (175 x 69 x 55 mm) 8.66 x 3.15 x 3.15 in (220 x 80 x 80 mm) 10.24 x 3.86 x 3.74 in (260 x 98 x 95 mm) Weight 29.3 oz (830 g) 29.3 oz (830 g) 38.8 oz (1100 g) 49.4 oz (1400 g) Storage Temperature -22 ~ 140 °F (-30 ~ +60 °C) RH 95 % max -22 ~ 140 °F (-30 ~ +60 °C) RH 95 % max -22 ~ 140 °F (-30 ~ +60 °C) RH 95 % max -22 ~ 140 °F (-30 ~ +60 °C) RH 95 % max Operating Temperature 14 ~ 122 °F (-10 ~ +50 °C) RH 95 % MAX 14 ~ 122 °F (-10 ~ +50 °C) RH 95 % max 14 ~ 122 °F (-10 ~ +50 °C) RH 95 % max 14 ~ 122 °F (-10 ~ +50 °C) RH 95 % max High Resolution Indoor/Outdoor IR CCTV Bullet Camera User Manual 9 SECTION 4: SPECIFICATIONS Table 2. Specifications for BC700 series cameras Model BC700 BC700VF BC700VFE Sensor 1/3" Sony Super-HAD CCD II 1/3" Sony Super-HAD CCD II 1/3" Sony Super-HAD CCD II Effective Picture Elements (H×V) 976 (H) x 494 (V) 976 (H) x 494 (V) 976 (H) x 494 (V) Horizontal Resolution 700 TV Line 700 TV Line 700 TV Line Minimum Illumination 0.001 lux F1.2 0.001 lux F1.2 0.001 lux F1.2 / 0 lux (with IR LED on) S/N Ratio More than 52 dB More than 52 dB More than 52 dB Scanning System 2:1 interface 2:1 interface 2:1 interface Synchronous System Internal, negative sync. Internal, negative sync. Internal, negative sync. Auto Electronic Shutter 1/60 s ~ 1/100,000 s 1/60 s ~ 1/100,000 s 1/60 s ~ 1/100,000 s Gamma Characteristic 0.45 0.45 0.45 IR Distance 65 ft (with Ø5 x 24 PCS Infrared LEDs) 131 ft (with Ø5 x 42 PCS Infrared LEDs) 196 ft (with Ø5 x 72 PCS Infrared LEDs) IR Status Under 10 lux by CDS -- Under 10 lux by CDS IR Power On CDS AUTO control -- CDS AUTO control Video Output 1 Vp-p, 75 Ω 1 Vp-p, 75 Ω 1 Vp-p, 75 Ω Auto Gain Control Auto Auto Auto Power/Current 12 Vdc (+/-10%) / 350 mA 12 Vdc (+/-10%) / 500 mA 12 Vdc (+/-10%) / 800 mA Lens 3.6mm / F2.0 2.8 - 12 mm manual zoom 2.8 - 12 mm manual zoom Dimensions (w x h x d) 6.89 x 2.72 x 2.17 in (175 x 69 x 55 mm) 8.66 x 3.15 x 3.15 in (220 x 80 x 80 mm) 10.24 x 3.86 x 3.74 in (260 x 98 x 95 mm) Weight 29.3 oz (830 g) 38.8 oz (1100 g) 49.4 oz (1400 g) Storage Temperature -22 ~ 140 °F (-30 ~ +60 °C) RH 95 % max -22 ~ 140 °F (-30 ~ +60 °C) RH 95 % max -22 ~ 140 °F (-30 ~ +60 °C) RH 95 % max Operating Temperature 14 ~ 122 °F (-10 ~ +50 °C) RH 95 % max 14 ~ 122 °F (-10 ~ +50 °C) RH 95 % max 14 ~ 122 °F (-10 ~ +50 °C) RH 95 % max 10 APPENDIX A: TROUBLESHOOTING APPENDIX A Troubleshooting Problem Possible Cause Nothing appears on the screen - Check the power connection. - Check the video signal cable connection to the monitor. The video image is dim or not clear. - If the camera lens is dirty, clean it with a soft, clean cloth. - Adjust the monitor controls, if necessary. - If the camera is facing a very strong light, change the camera position. - Adjust the lens focus. The screen is dark. - Adjust the contrast control of the monitor. - If you have an intermediate device, set the impedance (75 Ω /Hi-Z) properly, and check the cable connections. The camera is not working properly and the surface of the camera is hot. - Verify that the camera is correctly connected to an appropriate regulated power source. The MOTION DETECTION function is not working - Is “MOTION DETECTION” mode turned on? - Check the setting of the MD AREA. The image on the monitor flickers - Make sure that the camera isn’t facing direct sunlight or fluorescent light. If necessary,change the camera position. Colors are not quite right. - Check the settings in the WHITE BAL menu. High Resolution Indoor/Outdoor IR CCTV Bullet Camera User Manual 11 12
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Author : Observint Technologies Create Date : 2013:11:07 15:33:32-06:00 Modify Date : 2013:11:07 15:36:20-06:00 Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Format : application/pdf Title : High Resolution Indoor/Outdoor IR Color CCTV Bullet Camera User Manual Creator : Observint Technologies Metadata Date : 2013:11:07 15:36:20-06:00 Creator Tool : Adobe InDesign CS6 (Windows) Instance ID : uuid:5c98ed25-427d-4bfc-ad9e-10d1e0e6c986 Original Document ID : xmp.did:2F951AA610EFDE11BDB0C3326AF6BA41 Document ID : xmp.id:971CE0F6F347E311A93ACC2F150C68B4 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:961CE0F6F347E311A93ACC2F150C68B4 Derived From Document ID : xmp.did:BA1F5F8B6C21DF11883C94FDE14B4E8C Derived From Original Document ID: xmp.did:2F951AA610EFDE11BDB0C3326AF6BA41 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Windows) History Changed : / History When : 2013:11:07 15:33:32-06:00 Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 16EXIF Metadata provided by EXIF.tools