Bn Manual

User Manual:

Open the PDF directly: View PDF .
Page Count: 24

Download
Open PDF In Browser	View PDF

BANSHEE

TUBE CLEANING NOZZLES
USER MANUAL
*INCLUDES” 40K MODEL

PL 667 REV C
(02/2019)

TABLE OF CONTENTS
.MANUFACTURER’S INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
SPECIFICATIONS FOR ALL MODELS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
KEY FEATURES FOR ALL MODELS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
.
WARNING AND SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

22K PSI (1500 BAR) BANSHEE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
HEAD CONFIGURATIONS AND INLET CONNECTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
TYPES OF APPLICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
MAINTENANCE AND PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
40K PSI (2800 BAR) BANSHEE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
HEAD CONFIGURATIONS AND INLET CONNECTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
MAINTENANCE AND PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
TERMS AND CONDITIONS AND WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

This manual must be used in accordance with all applicable national laws. The manual shall be
regarded as a part of the machine and shall be kept for reference until the final dismantling of the
machine, as defined by applicable national law(s).
Updated manuals can be downloaded at:
https://www.stoneagetools.com/manuals

866-795-1586 • WWW. STONEAGETOOLS.COM

MANUFACTURER’S INFORMATION
StoneAge Inc.
466 S. Skylane Drive
Durango, CO 81303, USA
Phone: 970-259-2869
Toll Free: 866-795-1586
www.stoneagetools.com

StoneAge Europe
Unit 2, Britannia Business Centre
Britannia Way
Malvern WR14 1GZ
United Kingdom
Phone: +44 (0) 1684 892065

Banshee Model Specifications
Tool
Model

Tube ID
Range

*Pressure
Range

Flow
Range

Inlet Connections

Tool
Diameter

Tool
Length

Max
Water
Temp

BN9.5

.47-.63 in.
12-16mm

8-22k psi
550-1500 bar

5-6 gpm
19-23 l/min

.20

M7
1/16 NPT
1/4-28 MP LH & RH

.37 in.
9.5mm

2.6 in.
65mm

250ºF
120ºC

BN13

.6-1.0 in.
15-25mm

8-22k psi
550-1500 bar

7–9 gpm
26-34 l/min

.27

1/8 NPT
1/8 BSPP
1/4-28 MP LH & RH
3/8-24 MP LH & RH

.5 in.
13mm

2.9 in.
74mm

250ºF
120ºC

40k
BN13

.6-1.0 in.
15-25mm

20–40k psi
1400–2800 bar

4.5–6 gpm
17-23 l/min

.20

1/4-28 HP LH & RH
3/8 HP LH & RH

.5 in.
13mm

3.5 in.
89mm

250ºF
120ºC

BN15

.75-1.2 in.
19-30mm

8-22k psi
550-1500 bar

8-10 gpm
30-38 l/min

.35

1/8 NPT
1/8 BSPP
3/8-24 MP LH & RH

.6 in.
15mm

3.0 in.
76mm

250ºF
120ºC

BN18

.87-1.3 in.
22-33mm

8-22k psi
550-1500 bar

8–14 gpm
30–53 l/min

.66

1/4 NPT
1/4 BSPP
9/16-18 MP LH & RH

.69 in.
18mm

3.8 in.
97mm

250ºF
120ºC

40k
BN18

.87-1.3 in.
22-33mm

20–40k psi
1400–2800 bar

5–8.5 gpm
19-32 l/min

.25

3/8 HP LH & RH
9/16-18 HP LH & RH
M14 LH

.69 in.
18mm

4.7 in.
120mm

250ºF
120ºC

BN24

1.1-2.0 in.
28-51mm

8-22k psi
550-1500 bar

11-24 gpm
28-51 l/min

.90

3/8 NPT
3/8 BSPP
9/16-18 MP LH & RH

.93 in.
24mm

5.1 in.
130mm

250ºF
120ºC

40k
BN27

1.25-2.0 in.
32-51mm

20–40k psi
1400–2800 bar

5–8.5 gpm
19-32 l/min

.30

9/16-18 HP LH
M14 LH

1.06 in.
27mm

5.5 in.
140mm

250ºF
120ºC

BN33

1.5-2.4 in.
38-60mm

8-22k psi
550-1500 bar

11–48 gpm
42–182 l/min

2.3

11/2 NPT
1/2 BSPP
9/16 MP Gland

1.3 in.
33mm

6.9 in.
180mm

25ºF
120ºC

* The Maximum working pressure for different Banshee swivels is dependent on the inlet connection.

DESCRIPTION OF EQUIPMENT AND INTENDED USE

KEY FEATURES:

Banshee tube cleaning nozzles use high pressure water as
a liquid bearing, thereby eliminating ball bearings, seals or
lubricant used in conventional rotary tools. Each tool is easily
configured to suit any application by choosing from a variety
of replaceable heads and inlet options.

• Patented liquid bearing design means no
bearings, seals or lubricants to replace
• Stainless steel construction for extreme
durability and longevity
• Multiple inlet options and replaceable
heads make configurations easy

APPLICATIONS:
• Unplugging, cleaning, and polishing tubes, such as those
found in heat exchangers and industrial tube bundles
• Effectively removes thin, hard scale, carbons, coke, and
polymers
• Ideal for manual and powered lancing operations

866-795-1586 • WWW.STONEAGETOOLS.COM

WARNING AND SAFETY INSTRUCTIONS

WARNING
Operations with this equipment can be potentially hazardous. Caution must be exercised prior to and during
machine and water jet tool use. Please read and follow all of these instructions, in addition to the guidelines
in the WJTA Recommended Practices handbook, available online at www.wjta.org. Deviating from safety
instructions and recommended practices can lead to severe injury and/or death.
• Do not exceed the maximum operating pressure specified for any component in a system. The immediate work
area must be marked off to keep out untrained persons.
• The Dump Valve is the most important safety device. Each operator must have and be able to use their own
Dump Valves to shut down the water pressure immediately if necessary.
• Inspect the equipment and nozzle for visible signs of deterioration, damage, and improper assembly. Do not
operate until repaired. Make sure all threaded connections are tight and free of leaks.
• All operators and persons in close proximity must wear personal protective equipment, including approved
protection for body, hands, feet, face, ears, eyes, and air passages. Please refer to the WJTA Recommended
Practices, Section 6.
• Water pressure greater than 20,000 psi (1379 bar) can reach 200oF (93oc) and can scald or burn the operator.
Always use face shields, water jet resistant armor, and gloves to protect the operator from being burned or cut.
• Inspect the high pressure hose for damage. Use ONLY hoses or flex lances intended for waterblast applications
and rated for the maximum operating pressure on the job. The high pressure hose crimp/end fitting should be
equal to or less than the diameter of the BANSHEE tool. The high pressure hose should be as large as possible
to minimize pressure loss through the hose. There is increased risk of hydraulicking when cleaning plugged
tubes, when using larger ends.
• A Stinger is a rigid piece of pipe or tubing used between the end of the hose and the BANSHEE tool. It is usually
2 feet but can vary in length and is primarily a safety device for hand lancing. DO NOT use the stinger as a pry
bar or to bang on a deposit. The stinger and/or BANSHEE may break or stop rotating while being forced against
a blockage. The coupling connecting the hose to the stinger should be of the Slimline type and no larger in
diameter than the BANSHEE tool body. Material could catch on a coupling that is greater in diameter and cause
hydraulicking to occur.
END
BANSHEE
FITTING
STINGER
TOOL
HOSE

COUPLING

• An Anti-Withdrawal Device must be used when flex lancing. These devices provide a mechanical stop to
prevent the waterjet tool from exiting the tube and injuring the operator during the cleaning operation. StoneAge
automated, hands-free, equipment is designed to protect the operator and provide backout prevention. If
StoneAge automated equipment is not being used with the flex lances then one of two StoneAge backout
prevention options should be used.
The VE-400 Safety Stop is designed to protect the operator form a flex-lance exiting the tube
sheet during cleaning operations.
The ProTex BPT-100 vertical splash guard is lightweight and durable to keep operators safe from the
potential hazards of flex-lancing.

VE-400
SAFETY STOP

PROTEX
BPT-100

866-795-1586 • WWW. STONEAGETOOLS.COM

22K PSI (1500 BAR) BANSHEE HEAD CONFIGURATIONS
The BANSHEE tool diameter and inlet nut connection determine the operating pressure and part
number. BANSHEE tools can be used at operating pressures ranging from 1000psi (69 Bar) to 22,000psi
(1500 Bar). The pull of the three standard heads ranges from 3 to 5 pounds and is capable of a range of
pressures and flows.
105º

85º

145º

140º

90º
30º

30º

20º

15º

105º

140º

85º

POLISHER 042
4 Ports: 2 @ 85º, 2 @ 105º

145º

45º

UNPLUGGER 043
5 Ports:1 @ 15º, 1 @ 30º
1 @ 45º, 2 @ 145º

90º

60º

UNIVERSAL 044
7 Ports: 1 @ 20º, 1 @ 30º
1 @ 60º, 2 @ 90º, 2 @ 145º

*BSPP=British Standard Pipe LH= Left Hand

RH=Right Hand
MP=Medium Pressure NPT=National Pipe Thread

Table 1 - Tool Specifications
Part Number

*Inlet Connection

Max Pressure

Table 2 - Head Options
Part Number

Pressure Range

Flow

BN9.5-A

10,000 -15,000 psi

5-6 gpm

15,000 -22,000 psi

5-6 gpm

8,000 -15,000 psi

7-10 gpm

12,000 -22,000 psi

7-10 gpm

8,000 -15,000 psi

7-10 gpm

12,000 -22,000 psi

7-10 gpm

BN9.5-P1

1/16 NPT

15kpsi / 1035 bar

BN9.5-M7

M7-1.0

22kpsi / 1500 bar

-B

BN9.5-MP4L

1/4-28 LH

22kpsi / 1500 bar

BN13-A

22kpsi / 1500 bar

-C

15kpsi / 1035 bar

BN15-A

18kpsi / 1250 bar

-C

22kpsi / 1500 bar

BN18-A

8,000 -15,000 psi

11-14 gpm

22kpsi / 1500 bar

-B

8,000 -15,000 psi

8-10 gpm

22kpsi / 1500 bar

-C

12,000 -22,000 psi

11-14 gpm

22kpsi / 1500 bar

-D

12,000 -22,000 psi

8-10 gpm

BN24-A

8,000 -15,000 psi

19-24 gpm

BN9.5-MP4R
BN13-P2

1/4-28 RH
1/8 NPT

BN13-BSPP2
BN13-MP4L

1/8 BSPP
1/4-28 LH

BN13-MP4R

1/4-28 RH

BN13-MP6L

3/8-24 LH

BN13-MP6R

3/8-24 RH

BN15-P2

1/8 NPT

15kpsi / 1035 bar

BN15-BSPP2

1/8 BSPP

18kpsi / 1250 bar

-B

8,000 -15,000 psi

14-18 gpm

BN15-MP6L

3/8-24 LH

22kpsi / 1500 bar

-C

8,000 -15,000 psi

11-13 gpm

BN15-MP6R

3/8-24 RH

22kpsi / 1500 bar

-D

12,000 -22,000 psi

17-20 gpm

BN18-P4

1/4 NPT

15kpsi / 1035 bar

-E

12,000 -22,000 psi

14-16 gpm

BN18-BSPP4

1/4 BSPP

20kpsi / 1400 bar

-F

12,000 -22,000 psi

11-13 gpm

BN18-MP9L

9/16-18 LH

22kpsi / 1500 bar

BN33-A

8,000 -15,000 psi

39-48 gpm

22kpsi / 1500 bar

-B

8,000 -15,000 psi

32-38 gpm

15kpsi / 1035 bar

-C

8,000 -15,000 psi

25-31 gpm

22kpsi / 1500 bar

-D

8,000 -15,000 psi

19-24 gpm

22kpsi / 1500 bar

-E

8,000 -15,000 psi

14-18 gpm

22kpsi / 1500 bar

-F

12,000 -22,000 psi

21-25 gpm

15kpsi / 1035 bar

-G

12,000 -22,000 psi

17-20 gpm

22kpsi / 1500 bar

-H

12,000 -22,000 psi

14-16 gpm

22kpsi / 1500 bar

-I

12,000 -22,000 psi

11-13 gpm

BN18-MP9R

9/16-18 RH

BN24-P6

3/8 NPT

BN24-BSPP6
BN24-MP9L

9/16-18 LH

BN24-MP9R

9/16-18 RH

BN33-P8

1/2 NPT

BN33-BSPP8
BN33-MP9

3/8 BSPP

1/2 BSPP
9/16 MP

866-795-1586 • WWW.STONEAGETOOLS.COM

22K PSI (1500 BAR) BANSHEE OPERATION
OPERATION STEPS:
1. Flush out the entire system before installing the BANSHEE tool on the end of the hose or stinger. A clean
water supply is needed for reliable operation and should contain no larger than 25 micron particulates.
2. Once the system is flushed, attach the BANSHEE tool and place it in an open tube while the operating
pressure is being set.
3. When the tool is at operating pressure, the water exiting the tool through the leak paths/weep holes will
keep external debris from entering the tool.
4. If the tool is not under pressure it should not be left inside a plugged tube. Doing so could allow debris
to enter and prevent rotation or cause damage to the tool.
5. If the tool does not rotate when the dump valve is closed, the operator should try closing the dump valve
slowly a few times to build up pressure until normal operation is achieved. This will also flush debris
from the tool.
6. The BANSHEE drilled nozzle head will last between 20 and 60 hours. Worn jets decrease the cutting
rate. The tool may begin to hydraulick when cleaning plugged tubes. This occurs when the jets are not
effectively cutting the material into smaller pieces.
7. When using BANSHEE tools in plugged tubes, do not jam the head into the deposit because this will
stop the rotation of the tool and impede the cutting ability. When the tool contacts the deposit, allow it to
cut away the material and advance at its own pace. If it stops advancing, pull back slightly on the hose
to move the head away from the deposit. This action also allows the jets to cut the deposit at different
angles. The hose should be gradually fed into and out of the tube, allowing time for the jets to do their
work. Repeat this process until the tube is unplugged.
8. When polishing tubes with scale, the tool has been observed passing through a 50 foot long scaled tube
in 10 seconds. While this is sufficient when cleaning easy-to-remove deposits, we recommend feeding
the tool through the tube at a slower rate. This will ensure adequate cleaning. Unless the deposit is very
easy to remove, this will not completely remove the scale.

NOTICE
Corrosion pitting is one of the most common failures of BANSHEE tools. Pitting can cause premature tool
failure due to cracking. StoneAge recommends the following to help extend the life of the BANSHEE tools.

After use, blow out excess water and debris.
Flush the tool with WD-40®
Store tool in WD-40®

22K PSI (1500 BAR) BANSHEE TROUBLESHOOTING
TOOL WILL NOT ROTATE:
• All BANSHEE tools have a tapered shaft that fits into a tapered body. These surfaces do not touch
during operation. Do not pull out on the head/shaft in order to rotate the tool, it will lock up. If this
happens, tap the head/shaft on a surface to knock it free.
• Operators should be cautioned not to pry sideways on the tool. This may break the shaft just
behind the head, particularly if a rigid stinger is being used in the inlet.
• Check the nozzle orifices in the head for plugging; if one becomes plugged the swivel will likely
not rotate. If this does not solve the problem, the swivel should be disassembled and inspected.
• There are four small holes exiting the tapered portion of the shaft; these should be checked for
debris and cleaned out. Blow out the body and wipe off the shaft to remove any debris.

WD-40® is a registered trademark of the WD-40 Corporation.

866-795-1586 • WWW. STONEAGETOOLS.COM

22K PSI (1500 BAR) BANSHEE OPERATION
DIFFERENT TYPES OF BANSHEE APPLICATIONS

SINGLE HORIZONTAL
LANCING WITH VE-400
SAFETY STOP

SINGLE VERTICAL LANCING
WITH PROTEX BPT-100

DUAL OR TRIPLE
HORIZONTAL LANCING WITH
HANDS-FREE AUTOBOX® TRACTOR

866-795-1586 • WWW.STONEAGETOOLS.COM

22K PSI (1500 BAR) BANSHEE MAINTENANCE

NOTICE
DO NOT USE A PIPE WRENCH OR PLIERS WITH TEETH
This can crush and crack the hardened steel body, leading to tool breakage during operation.

The nozzle heads are wear items that will need to be replaced after 20 to 60 hours, depending on water
filtration and operating pressure. All BANSHEE tools require the use of a correctly sized open-end
wrench to fit the flats provided on the inlet nut when attaching the tool to the lance. The wrench flats
should always be used when maintaining these tools. TABLE 3 details the wrench size required for each
part of the tools and the available kits that contain the wrenches for each tool model.

Table 3 - Recommended Torque Ranges and Required Wrench Sizes
StoneAge
Tool Kit
Number

BN9.5 612

BN13 612

BN15 612

BN18 612

BN24 612

BN33 612

Part

Wrench
Size (in)

Shaft

3/16

Head

5/16

Body

11/32

Nut

5/16

Shaft

13/64

Head

3/8

Body

7/16

Nut

7/16

Shaft

1/4

Head

1/2

Body

1/2

Nut

1/2

Shaft

5/16

Head

9/16

Body

9/16

Nut

5/8

Shaft

1/2

Head

13/16

Body

13/16

Nut

13/16

Shaft

9/16

Head

1-1/8

Body

1-1/8

Nut

1-1/8

Recommended Torque Ranges (with anti-seize)
IN-LBS

FT-LBS

N-m

3.3

4.1

4.5

194

216

24.4

5.8

7.1

7.9

270

300

30.5

33.9

108

120

12.2

13.6

315

350

35.6

39.5

180

200

16.7

20.3

22.6

540

600

67.8

432

480

48.8

54.2

756

840

85.4

94.9

486

540

54.9

1080

1200

100

122

135.6

866-795-1586 • WWW. STONEAGETOOLS.COM

22K PSI (1500 BAR) BANSHEE MAINTENANCE
Head to Shaft torque recommendation
(See TABLE 3 previous page)
Head
(BN9.5, BN13, BN15,
BN18, BN24, or BN33)

BNxx 002
Inlet Nut

BNxx 001
Shaft
BNxx 003
Body
Inlet Nut, Shaft, and Body =
“Swivel Assembly”

*BNxx is used to denote the
BN9.5, BN13, BN15, BN18,
BN24, or BN33 tools

DISASSEMBLY STEPS:
1. Layout the appropriate size open end wrenches for the tool intended for maintenance. See Table 3
on the previous page for list of wrench sizes.
2. Locate the flats on the Head and tighten them in a vice, so that the nut end of the tool is facing up.
3. Slide a wrench onto the flats of the Shaft and loosen the Swivel Assembly from the head.
4. Remove the BANSHEE from the vice and unscrew the Head from the Swivel Assembly.
5. Place an adjustable 1-1/8” wrench in the vice, so the flat side of the claw is parallel to the floor.
6. Slide the Inlet Nut flats into the open end wrench. Using a second open end wrench on the Body
flats, loosen the Body from the Inlet Nut and unscrew.
7. The Shaft should just drop out of the Body and the Disassembly is complete.

CLEAN:
1. Use a pin gauge or needle to make sure all orifices in all four parts are free of debris. The holes in
the Shaft are critical for proper rotation.
2. After cleaning each part, blow out excess water.

INSPECT:
1. Heads are designed for 20-60 hours of wear dependent upon water quality and operating pressure.
Worn head will decrease the cutting rates and overall productivity. Inspect the head for dents,
pock marks, and jets. When in doubt replace the Head.
2. Inspect the Shaft for cracking, pitting, or uneven wear.

ASSEMBLY STEPS:
1. Position the stem of the Shaft into the Inlet Nut.
2. Slide the Body over the Shaft and screw onto the Inlet Nut.
3. Place an adjustable 1-1/8” wrench in the vice, so the flat side of the claw is parallel to the floor.
Slide the Inlet Nut flats into the open end wrench. Using a second open end wrench on the Body
flats, tighten the Body to the Inlet Nut.
4. Screw the Head onto the Shaft. Locate the flats on the Head and tighten them in a vice, so that the
nut end of the tool is facing up.
5. Slide a wrench onto the flats of the Shaft and tighten the Swivel Assembly to the head.

After use, blow out excess water and debris.
Flush the tool with WD-40®
Store tool in WD-40®
866-795-1586 • WWW.STONEAGETOOLS.COM

40K PSI (2800 BAR) BANSHEE
The 40k psi (2800 bar) BANSHEES are self-rotating swivels designed for tube cleaning. The diameter of
the tool and inlet nut connection determine the model and part number. The tool can be used at operating pressures from 25,000 psi to 40,000 psi, depending on the inlet connection and head jetting. Unlike
the lower pressure Banshees, the 40k psi (2800 bar) BANSHEE heads come with threaded replaceable
sapphire nozzle inserts
NOZZLE HEADS:
Two standard head designs are available and both are capable of a range of pressure and flows. The
nozzles in all heads are all OS2 Sapphire nozzles. Different orifice sizes in the nozzles accommodate different pressure and flow combinations. Refer to TABLE 7 for Head Jetting and Flow specifications. The
pull of the standard heads ranges from 3.5 to 4 pounds.
110º

85º

140º

30º
15º

110º

140º

85º

POLISHER 442
4 Ports: 2 @ 85º, 2 @ 110º

UNPLUGGER 443
5 Ports:1 @ 15º, 1 @ 30º
1 @ 50º, 2 @ 140º

Table 6 - Tool Specifications

*Inlet Connection

Table 7 - Head Options

BN13-H4L

14-28 LH

40kpsi / 2800 bar

Part Number

OS2-0XX
Front Jet
Size

BN13-H6L

3/8-24 LH

40kpsi / 2800 bar

BN13 442-C

2 x .014

2 x .015

5.5-6 gpm

BN18-H6L

3/8-24 LH

40kpsi / 2800 bar

-D

2 x .010

2 x .014

4.5-5 gpm

BN18-H9L

9/16-18 LH

40kpsi / 2800 bar

BN13 443-C

3 x .010

2 x .016

5.5-6 gpm

BN18-H9R

9/16-18 RH

40kpsi / 2800 bar

-D

3 x .009

2 x .015

4.5-5 gpm

BN18-HM14L

M14 x 1.5 LH

40kpsi / 2800 bar

BN18 442-A

2 x .020

2 x .017

8-8.5 gpm

BN27-H9L

9/16-18 LH

40kpsi / 2800 bar

-B

2 x .018

2 x .017

7-7.5 gpm

BN27-HM14L

M14 x 1.5 LH

40kpsi / 2800 bar

-C

2 x .015

6-6.5 gpm

Part Number

Max Pressure

*BSPP=British Standard Pipe LH= Left Hand

RH=Right Hand
MP=Medium Pressure NPT=National Pipe Thread

140º 50º

OS2-0XX
Back Jet
Size

Flow

-D

2 x .010

2 x .014

5-5.5 gpm

BN18 443-A

3 x .014

2 x .020

8-8.5 gpm

-B

3 x .013

2 x .019

7-7.5 gpm

-C

3 x .011

2 x .016

6-6.5 gpm

-D

3 x .009

2 x .014

5-5.5 gpm

BN27 442-A

2 x .018

8-8.5 gpm

-B

2 x .015

2 x .016

7-7.5 gpm

-C

2 x .011

2 x .015

6-6.5 gpm

-D

2 x .009

2 x .013

5-5.5 gpm

BN27 443-A

3 x .013

2 x .019

8-8.5 gpm

-B

3 x .011

2 x .017

7-7.5 gpm

-C

3 x .009

2 x .014

6-6.5 gpm

-D

3 x .006

2 x .013

5-5.5 gpm

866-795-1586 • WWW. STONEAGETOOLS.COM

40K PSI (2800 BAR) BANSHEE OPERATION

WARNING
Operators MUST adhere to the Warning and Safety Instructions on Page 5 of this manual.
OPERATION STEPS:
1. Flush out the entire system before installing the BANSHEE tool on the end of the hose or stinger. A clean
water supply is needed for reliable operation and should contain no larger than 25 micron particulates.
2. Once the system is flushed, attach the BANSHEE tool and place it in an open tube while the operating
pressure is being set.
3. When the tool is at operating pressure, the water exiting the tool through the leak paths/weep holes will
keep external debris from entering the tool.
4. If the tool is not under pressure it should not be left inside a plugged tube. Doing so could allow debris
to enter and prevent rotation or cause damage to the tool.
5. If the tool does not rotate when the dump valve is closed, the operator should try closing the dump valve
slowly a few times to build up pressure until normal operation is achieved. This will also flush debris
from the tool.
6. Sapphire nozzles can last several hundred hours with proper care. Worn jets decrease the cutting
rate. The tool may begin to hydraulick when cleaning plugged tubes. This occurs when the jets are not
effectively cutting the material into smaller pieces.
7. When using BANSHEE tools in plugged tubes, do not jam the head into the deposit because this will
stop the rotation of the tool and impede the cutting ability. When the tool contacts the deposit, allow it to
cut away the material and advance at its own pace. If it stops advancing, pull back slightly on the hose
to move the head away from the deposit. This action also allows the jets to cut the deposit at different
angles. The hose should be gradually fed into and out of the tube, allowing time for the jets to do their
work. Repeat this process until the tube is unplugged.
8. When polishing tubes with scale, the tool has been observed passing through a 50 foot long scaled tube
in 10 seconds. While this is sufficient when cleaning easy-to-remove deposits, we recommend feeding
the tool through the tube at a slower rate. This will ensure adequate cleaning. Unless the deposit is very
easy to remove, this will not completely remove the scale.

After use, blow out excess water and debris.
Flush the tool with WD-40®
Store tool in WD-40®

40K PSI (2800 BAR) BANSHEE TROUBLESHOOTING
TOOL WILL NOT ROTATE:
• All BANSHEE tools have a tapered shaft that fits into a tapered body. These surfaces do not touch
during operation. Do not pull out on the head/shaft in order to rotate the tool, it will lock up. If this
happens, tap the head/shaft on a surface to knock it free.
• Operators should be cautioned not to pry sideways on the tool. This may break the shaft just
behind the head, particularly if a rigid stinger is being used in the inlet.
• Check the nozzle orifices in the head for plugging; if one becomes plugged the swivel will likely not
rotate. If this does not solve the problem, the swivel should be disassembled and inspected.
• There are two small holes exiting the tapered portion of the shaft; these should be checked for
debris and cleaned out. Blow out the body and wipe off the shaft to remove any debris.

866-795-1586 • WWW.STONEAGETOOLS.COM

40K PSI (2800 BAR) BANSHEE MAINTENANCE
OS2 SAPPHIRE NOZZLES:
The life of the sapphire nozzle inserts depends on water filtration. If any particle hits the sapphire, it
will be instantly ruined. With clean water and proper care, they can last for several hundred hours. 40k
BANSHEE wrench kits also include a 1/16” allen and LOCTITE® 680 for replacing the nozzles.

REPLACING SAPPHIRE NOZZLES:
1. To remove worn nozzle inserts, heat the head with a propane torch for a minute or just enough to
break down the thread-locker.
2. All nozzle inserts can be installed using the 1/16” allen wrench and a drop of the LOCTITE® 680
provided in the wrench kits.
BNXX 442-XX
Polisher Head

BNxx 402
Inlet Nut

OS2-XXX
Sapphire
Nozzles

BNxx 401
Shaft
BNxx 403
Body

*BNxx is used to denote the
BN13, BN18 or BN27 tools

BNXX 443-XX
Unplugger Head

NOTICE
DO NOT USE A PIPE WRENCH OR PLIERS WITH TEETH
This can crush and crack the hardened steel body, leading to tool breakage during operation.
*StoneAge does NOT recommend replacing 40k BANSHEE (with the exception of OS2 nozzles) due to
tight tolerances and unknown or uncontrolled condition and fit of the original parts.
All BANSHEE tools require the use of a correctly sized open-end wrench to fit the flats provided on the
inlet nut when attaching the tool to the lance. The wrench flats should always be used when maintaining
these tools. TABLE 8 details the wrench size required for each part of the tools and the available kits
that contain the wrenches, one 1/6” allen hex key, and LOCTITE® 680 for each tool model.
Table 8 - Recommended Torque Ranges and Required Wrench Sizes
StoneAge
Tool Kit
Number

BN13 612-H

BN18 612-H6L

BN27 612-H9L

Part

Wrench
Size (in)

Shaft

3/16

Head

5/16

Body

11/32

Nut

5/16

Shaft

13/64

Head

3/8

Body

7/16

Nut

7/16

Shaft

1/2

Head

7/8

Body

15/16

Nut

15/16

Recommended Torque Ranges (with anti-seize)
IN-LBS

FT-LBS

N-m

5.8

7.1

7.9

270

300

30.5

33.9

180

200

16.7

20.3

22.6

540

600

67.8

432

480

48.8

54.2

918

1020

103.7

115.2

LOCTITE® is a registered trademark of the Henkel Corporation.

866-795-1586 • WWW. STONEAGETOOLS.COM

22K (1500 BAR) PART NUMBERS
PRESSURE

PART NUMBER

STYLE

FLOW RANGE

BN9.5 HEAD SELECTION
10-15k psi
(700-1000 bar)

15-22k psi
(1000-1500 bar)

BN9.5 042-A

Polisher

BN9.5 043-A

Unplugger

5-6 gpm

(19-23 l/min)

BN9.5 042-B

Polisher

5-6 gpm

(19-23 l/min)

BN9.5 043-B

Unplugger

5.5-6.5 gpm

(21-25 l/min)

BN9.5 044-1

Universal

7.0-8.0 gpm

(27-30 l/min)

BN13 042-A

Polisher

7-9 gpm

(27-34 l/min)

4.5-5.5 gpm

(17-21 l/min)

BN13 HEAD SELECTION
10-15k psi
(700-1000 bar)

15-22k psi
(1000-1500 bar)

BN13 043-A

Unplugger

7-9 gpm

(27-34 l/min)

BN13 044-A

Universal

8-10 gpm

(30-38 l/min)

BN13 042-C

Polisher

7-9 gpm

(27-34 l/min)

BN13 043-C

Unplugger

7-9 gpm

(27-34 l/min)

BN13 044-C

Universal

8-10 gpm

(30-38 l/min)

BN15 HEAD SELECTION
10-15k psi
(700-1000 bar)

15-22k psi
(1000-1500 bar)

BN15 042-A

Polisher

7-9 gpm (27-34 l/min)

BN15 043-A

Unplugger

7-9 gpm (27-34 l/min)

BN15 044-A

Universal

8-10 gpm (30-38 l/min)

BN15 042-C

Polisher

7-9 gpm (27-34 l/min)

BN15 043-C

Unplugger

7-9 gpm (27-34 l/min)

BN15 044-C

Universal

8-10 gpm (30-38 l/min)

BN18 HEAD SELECTION

10-15k psi
(700-1000 bar )

15-22k psi
(1000-1500 bar)

BN18 042-A

Polisher

11-14 gpm

(42-53 l/min)

BN18 042-B

Polisher

8-10 gpm

(30-38 l/min)

BN18 043-A

Unplugger

11-14 gpm

(42-53 l/min)

BN18 043-B

Unplugger

8-10 gpm

(30-38 l/min)

BN18 044-A

Universal

11-14 gpm

(42-53 l/min)

BN18 044-B

Universal

8-10 gpm

(30-38 l/min)

BN18 042-C

Polisher

11-14 gpm

(42-53 l/min)

BN18 042-D

Polisher

8-10 gpm

(30-38 l/min)

BN18 043-C

Unplugger

11-14 gpm

(42-53 l/min)

BN18 043-D

Unplugger

8-10 gpm

(30-38 l/min)

BN18 044-C

Universal

11-14 gpm

(42-53 l/min)

866-795-1586 • WWW.STONEAGETOOLS.COM

22K (1500 BAR) PART NUMBERS
PRESSURE

PART NUMBER

STYLE

FLOW RANGE

BN24 HEAD SELECTION

10-15k psi
(700-1000 bar)

15-22k psi
(1000-1500 bar)

BN24 042-A

Polisher

20-25 gpm

(76-95 l/min)

BN24 042-B

Polisher

15-19 gpm

(57-72 l/min)

BN24 042-C

Polisher

12-14 gpm

(45-53 l/min)

BN24 044-A

Universal

20-25 gpm

(76-95 l/min)

BN24 044-B

Universal

15-19 gpm

(57-72 l/min)

BN24 044-C

Universal

12-14 gpm

(45-53 l/min)

BN24 042-D

Polisher

18-21 gpm

(68-80 l/min)

BN24 042-E

Polisher

15-17 gpm

(57-64 l/min)

BN24 042-F

Polisher

12-14 gpm

(45-53 l/min)

BN24 044-D

Universal

18-21 gpm

(68-80 l/min)

BN24 044-E

Universal

15-17 gpm

(57-64 l/min)

BN24 044-F

Universal

12-14 gpm

(45-53 l/min)

BN33 044-A

Universal

40-49 gpm

(150-190 l/min)

BN33 044-B

Universal

33-39 gpm (130-150 l/min)

BN33 044-C

Universal

26-32 gpm

(98-120 l/min)

BN33 044-D

Universal

20-25 gpm

(76-95 l/min)

BN33 044-E

Universal

15-19 gpm

(57-72 l/min)

BN33 044-F

Universal

22-26 gpm

(83-98 l/min)

BN33 044-G

Universal

18-21 gpm

(68-80 l/min)

BN33 044-H

Universal

15-17 gpm

(57-64 l/min)

BN33 044-I

Universal

BN33 HEAD SELECTION

10-15k psi
(700-1000 bar)

15-22k psi
(1000-1500 bar)

12-14 gpm

(45-53 l/min)

866-795-1586 • WWW. STONEAGETOOLS.COM

40K (2800 BAR) PART NUMBERS
PRESSURE

PART NUMBER

STYLE

FLOW RANGE

BN13 40K HEAD SELECTION
BN13 442-C

Polisher

5.5-6 gpm

21-23 l/min

BN13 442-D

Polisher

4.5-5 gpm

17-19 l/min

BN13 443-C

Unplugger

5.5-6 gpm

21-23 l/min

BN13 443-D

Unplugger

4.5-5 gpm

17-19 l/min

BN18 442-A

Polisher

8-8.5 gpm

(30-32 l/min)

BN18 442-B

Polisher

7-7.5 gpm

(27-28 l/min)

BN18 442-C

Polisher

6-6.5 gpm

(23-25 l/min)

BN18 442-D

Polisher

5-5.5 gpm

(19-21 l/min)

BN18 443-A

Unplugger

8-8.5 gpm

(30-32 l/min)

BN18 443-B

Unplugger

7-7.5 gpm

(27-28 l/min)

BN18 443-C

Unplugger

6-6.5 gpm

(23-25 l/min)

BN18 443-D

Unplugger

5-5.5 gpm

(19-21 l/min)

30-40k psi
(2100-2800 bar)

BN18 40K HEAD SELECTION

30-40k psi
(2100-2800 bar)

866-795-1586 • WWW.STONEAGETOOLS.COM

40K (2800 BAR) PART NUMBERS
PRESSURE

PART NUMBER

STYLE

FLOW RANGE

BN27 40K HEAD SELECTION

30-40k psi
(2100-2800 bar)

BN27 442-A

Polisher

8-8.5 gpm

(30-32 l/min)

BN27 442-B

Polisher

7-7.5 gpm

(27-28 l/min)

BN27 442-C

Polisher

6-6.5 gpm

(23-25 l/min)

BN27 442-D

Polisher

5-5.5 gpm

(19-21 l/min)

BN27 443-A

Unplugger

8-8.5 gpm

(30-32 l/min)

BN27 443-B

Unplugger

7-7.5 gpm

(27-28 l/min)

BN27 443-C

Unplugger

6-6.5 gpm

(23-25 l/min)

BN27 443-D

Unplugger

5-5.5 gpm

(19-21 l/min)

866-795-1586 • WWW. STONEAGETOOLS.COM

NOTES

THIS PAGE LEFT INTENTIONALLY BLANK

866-795-1586 • WWW.STONEAGETOOLS.COM

NOTES

THIS PAGE LEFT INTENTIONALLY BLANK

866-795-1586 • WWW. STONEAGETOOLS.COM

NOTES

THIS PAGE LEFT INTENTIONALLY BLANK

866-795-1586 • WWW.STONEAGETOOLS.COM

TERMS AND CONDITIONS AND WARRANTY INFORMATION
1. Acceptance of Terms and Conditions. Receipt

3. Warranty. SELLER MAKES NO WARRANTIES OR

of these Terms and Conditions of Sale (“Terms and

REPRESENTATIONS AS TO THE PERFORMANCE

Conditions”) shall operate as the acceptance by

OF ANY PRODUCT EXCEPT AS SET FORTH IN THE

StoneAge, Inc. (“Seller”) of the order submitted by

STONEAGE LIMITED WARRANTY PROVIDED WITH THE

the purchaser (“Buyer”). Such acceptance is made

PRODUCT.

expressly conditional on assent by Buyer to these Terms
and Conditions. Such assent shall be deemed to have

4. Delivery. Seller is not obligated to make delivery by

been given unless written notice of objection to any of

a specified date, but will always use its best efforts to

these Terms and Conditions (including inconsistencies

make delivery within the time requested. The proposed

between Buyer’s purchase order and this acceptance) is

shipment date is an estimate. Seller will notify Buyer

given by Buyer to Seller promptly on receipt hereof.

promptly of any material delay and will specify the
revised delivery date as soon as practicable. UNDER

Seller desires to provide Buyer with prompt and efficient

NO CIRCUMSTANCES SHALL SELLER HAVE ANY

service. However, to individually negotiate the terms

LIABILITY WHATSOEVER FOR LOSS OF USE OR

of each sales contract would substantially impair

FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES

Seller’s ability to provide such service. Accordingly, the

RESULTING FROM DELAY REGARDLESS OF THE

product(s) furnished by Seller are sold only according

REASON(S).

to the terms and conditions stated herein and with the
terms and conditions stated in any effective StoneAge

All product(s) will be shipped F.O.B. point of origin,

Dealer Agreement or StoneAge Reseller Agreement, if

unless specifically agreed otherwise, and Buyer shall

applicable. Notwithstanding any terms and conditions

pay all shipping costs and insurance costs from that

on Buyer’s order, Seller’s performance of any contract

point. Seller, in its sole discretion, will determine and

is expressly made conditional on Buyer’s agreement

arrange the means and manner of transportation of the

to these Terms and Conditions unless otherwise

product(s). Buyer shall bear all risk of loss commencing

specifically agreed to in writing by Seller. In the absence

with the shipment or distribution of the product(s) from

of such agreement, commencement of performance,

Seller’s warehouse. Order shortages or errors must be

shipment and/or delivery shall be for Buyer’s

reported within fifteen (15) business days from receipt of

convenience only and shall not be deemed or construed

shipment to secure adjustment. No product(s) may be

to be an acceptance of Buyer’s terms and conditions.

returned without securing written approval from Seller.

2. Payment/Prices. Unless other arrangements have

5. Modification. These Terms and Conditions are

been made in writing between Seller and Buyer, payment

intended by Seller and Buyer to constitute a final,

for the product(s) shall be made upon receipt of invoice.

complete and exclusive expression of agreement

The prices shown on the face hereof are those currently

relating to the subject matter hereof and cannot be

in effect. Prices invoiced shall be per pricelist in effect

supplemented or amended without Seller’s prior written

at the time of shipment. Prices are subject to increase

approval.

for inclusion of any and all taxes which are applicable
and which arise from the sale, delivery or use of the

6. Omission. Seller’s waiver of any breach or Seller’s

product(s), and the collection of which Seller is or may

failure to enforce any of these Terms and Conditions

be responsible to provide to any governmental authority,

at any time, shall not in any way affect, limit or waive

unless acceptable exemption certificates are provided

Seller’s right thereafter to enforce and compel strict

by Buyer in accordance with applicable law. Buyer

compliance with every term and condition hereof.

shall pay all charges for transportation and delivery
and all excise, order, occupation, use or similar taxes,

7. Severability. If any provision of these Terms and

duties, levies, charges or surcharges applicable to the

Conditions is held to be invalid or unenforceable, such

product(s) being purchased, whether now in effect

invalidity or unenforceability shall not affect the validity

or hereafter imposed by any governmental authority,

or enforceability of the other portions hereof.

foreign or domestic.

866-795-1586 • WWW. STONEAGETOOLS.COM

TERMS AND CONDITIONS AND WARRANTY INFORMATION
8. Disputes. Seller and Buyer shall attempt in good

10. Jurisdiction and Venue. Seller and Buyer agree

faith to promptly resolve any dispute arising under

that the state or federal courts located within the City

these Terms and Conditions by negotiations between

and County of Denver, Colorado shall have sole and

representatives who have authority to settle the

exclusive jurisdiction over any litigation concerning any

controversy. If unsuccessful, Seller and Buyer shall

dispute arising under these Terms and Conditions not

further attempt in good faith to settle the dispute

otherwise resolved pursuant to Section 9 as well as any

by nonbinding third-party mediation, with fees and

alleged defects of any Products or damages sustained

expenses of such mediation apportioned equally to

as a result of such alleged defects. Seller and Buyer

each side. Any dispute not so resolved by negotiation

further agree that should any litigation be commenced

or mediation may then be submitted to a court of

in connection with such a dispute, it shall only be

competent jurisdiction in accordance with the terms

commenced in such courts. Seller and Buyer agree to

hereof. These procedures are the exclusive procedures

the exclusive jurisdiction of such courts and neither will

for the resolution of all such disputes between the Seller

raise any objection to the jurisdiction and venue of such

and Buyer.

courts, including as a result of inconvenience.

9. Governing Law. All sales, agreements for sale, offers

11. Attorney’s Fees. If any litigation is commenced

to sell, proposals, acknowledgments and contracts

between Seller and Buyer, or their personal

of sale, including, but not limited to, purchase orders

representatives, concerning any provision hereof,

accepted by Seller, shall be considered a contract under

the party prevailing in the litigation shall be entitled,

the laws of the State of Colorado and the rights and

in addition to such other relief that is granted, to a

duties of all persons, and the construction and effect of

reasonable sum as and for their attorneys’ fees and

all provisions hereof shall be governed by and construed

costs in such litigation or mediation.

according to the laws of such state.
STONEAGE TRADEMARK LIST
View the list of StoneAge’s trademarks and service marks and learn how the trademarks should be used. Use of
StoneAge trademarks may be prohibited, unless expressly authorized.
http://www.StoneAgetools.com/trademark-list/
STONEAGE PATENT DATA
View the list of StoneAge’s current U.S. patent numbers and descriptions.
http://www.sapatents.com
STONEAGE TERMS AND WARRANTY
View StoneAge’s Terms and Warranty Conditions online.
http://www.stoneagetools.com/terms
http://www.stoneagetools.com/warranty

866-795-1586 • WWW.STONEAGETOOLS.COM

TERMS AND CONDITIONS AND WARRANTY INFORMATION
WARRANTY:
Warranties set forth herein extend only to End-Users,

modification of the Product or use of parts not approved

meaning customers acquiring, or that have previously

by StoneAge will void this Limited Warranty. StoneAge

acquired, a product manufactured by StoneAge

reserves the right to change or improve the material and

(“Product”) for their own use and not for resale, either

design of the Product at any time without notice to End-

directly from StoneAge Inc. (“StoneAge”) or from a

User, and StoneAge is not obligated to make the same

StoneAge Authorized Dealer or Reseller (“Dealer”). No

improvements during warranty service to any Product

warranty of any kind or nature is made by StoneAge

previously manufactured.

beyond those expressly stated herein.

4. WARRANTY EXCLUSIONS. This Limited Warranty

1. LIMITED WARRANTY PERIOD. Subject to

does not cover, and StoneAge shall not be responsible

the limitations and conditions hereinafter set forth,

for the following, or damage caused by the following:

StoneAge warrants its Product to be free from defects

(1) any Product that has been altered or modified in any

in workmanship and material for a period of one (1) year

way not approved by StoneAge in advance in writing;

from the date of purchase by the End-User, provided that

(2) any Product that has been operated under more

the end of the limited warranty period shall not be later

severe conditions or beyond the rated capacity specified

than eighteen (18) months from the date of shipment of

for that Product; (3) depreciation or damage caused

the Product to the Dealer or the End-User by StoneAge

by normal wear and tear, failure to follow operation or

(“Limited Warranty Period”). All replacement parts which

installation instructions, misuse, negligence or lack

are furnished under this Limited Warranty and properly

of proper protection during storage; (4) exposure to

installed shall be warranted to the same extent as the

fire, moisture, water intrusion, electrical stress, insects,

original Product under this Limited Warranty if, and only

explosions, extraordinary weather and/or environmental

if, the original parts were found to be defective within the

conditions including, but not limited to lightning, natural

original Limited Warranty Period covering the original

disasters, storms, windstorms, hail, earthquakes, acts

Product. Replacement parts are warranted for the

of God or any other force majeure event; (5) damage to

remainder of the original Limited Warranty Period. This

any Product caused by any attempt to repair, replace,

Limited Warranty does not cover any component part of

or service the Product by persons other than StoneAge

any Product not manufactured by StoneAge. Any such

authorized service representatives; (6) costs of normal

component part is subject exclusively to the component

maintenance parts and services; (7) damage sustained

manufacturer’s warranty terms and conditions.

during unloading, shipment or transit of the Product;

2. LIMITED WARRANTY COVERAGE. StoneAge’s
sole obligation under this Limited Warranty shall be, at
StoneAge’s option and upon StoneAge’s inspection, to

or (8) failure to perform the recommended periodic
maintenance procedures listed in the Operator’s Manual
accompanying the Product.

repair, replace or issue a credit for any Product which is

5. REQUIRED WARRANTY PROCEDURES. To be

determined by StoneAge to be defective in material or

eligible for warranty service, the End-User must: (1)

workmanship. StoneAge reserves the right to examine

report the Product defect to the entity where the Product

the alleged defective Product to determine whether this

was purchased (i.e. StoneAge or the Dealer) within

Limited Warranty is applicable, and final determination

the Limited Warranty Period specified in this Limited

of limited warranty coverage lies solely with StoneAge.

Warranty; (2) submit the original invoice to establish

No statement or recommendation made by a StoneAge

ownership and date of purchase; and (3) make the

representative, Dealer or agent to End-User shall

Product available to a StoneAge authorized service

constitute a warranty by StoneAge or a waiver or

representative for inspection to determine eligibility

modification to any of the provisions hereof or create any

for coverage under this Limited Warranty. This Limited

liability for StoneAge.

Warranty shall not extend to any person or entity who
fails to provide proof of original purchase from StoneAge

3. WARRANTY SERVICE PROVIDERS. Service
and repair of the Product is to be performed only by
StoneAge authorized service representatives, including
Dealers who are authorized repair centers, with

or a Dealer. No Product may be returned for credit
or adjustment without prior written permission from
StoneAge.

StoneAge approved parts. Information about StoneAge
authorized service representatives can be obtained
through the StoneAge website at www.stoneagetools.
com/service. Unauthorized service, repair or

866-795-1586 • WWW. STONEAGETOOLS.COM

TERMS AND CONDITIONS AND WARRANTY INFORMATION

6. DISCLAIMER OF IMPLIED WARRANTIES AND OTHER
REMEDIES. EXCEPT AS EXPRESSLY STATED HEREIN
(AND TO THE FULLEST EXTENT ALLOWED UNDER
APPLICABLE LAW), STONEAGE HEREBY DISCLAIMS
ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WITHOUT LIMITATION ALL IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE, AND ANY AND ALL
WARRANTIES, REPRESENTATIONS OR PROMISES
AS TO THE QUALITY, PERFORMANCE OR FREEDOM
FROM DEFECT OF THE PRODUCT COVERED BY
THIS LIMITED WARRANTY. STONEAGE FURTHER
DISCLAIMS ALL IMPLIED INDEMNITIES.
7. LIMITATION OF LIABILITY. End-User specifically
acknowledges that the Product may be operated at
high speeds and/or pressures, and that as such it may
be inherently dangerous if not used correctly. EndUser shall familiarize itself with all operation materials
provided by StoneAge and shall at all times use and
require its agents, employees and contractors to use

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
IT IS UNDERSTOOD THAT STONEAGE’S LIABILITY,
WHETHER IN CONTRACT, IN TORT, UNDER ANY
WARRANTY, IN NEGLIGENCE, OR OTHERWISE SHALL
NOT EXCEED THE AMOUNT OF THE PURCHASE
PRICE PAID BY THE END-USER FOR THE PRODUCT.
STONEAGE’S MAXIMUM LIABILITY SHALL NOT
EXCEED, AND END-USER’S REMEDY IS LIMITED
TO EITHER (1) REPAIR OR REPLACEMENT OF THE
DEFECTIVE WORKMANSHIP OR MATERIAL OR, AT
STONEAGE’S OPTION, (2) REFUND OF THE PURCHASE
PRICE, OR (3) ISSUANCE OF A CREDIT FOR THE
PURCHASE PRICE, AND SUCH REMEDIES SHALL BE
END-USER’S ENTIRE AND EXCLUSIVE REMEDY.
YOU, THE END-USER, UNDERSTAND AND EXPRESSLY
AGREE THAT THE FOREGOING LIMITATIONS ON
LIABILITY ARE PART OF THE CONSIDERATION IN
THE PRICE OF THE STONEAGE PRODUCT YOU
PURCHASED.

all necessary and appropriate safety devices, guards

Some jurisdictions do not allow the limitation or

and proper safe operating procedures. In no event shall

exclusion of liability for certain damages, so the above

StoneAge be responsible for any injuries to persons or

limitations and exclusions may not apply to you. This

property caused directly or indirectly by the operation

Limited Warranty gives you specific legal rights, and you

of the Product if End-User or any agent, employee, or

may also have other rights which vary from jurisdiction

contractor of End-User: (1) fails to use all necessary

to jurisdiction. If any provisions of this Limited Warranty

and appropriate safety devices, guards and proper

is held to be invalid or unenforceable, such invalidity

safe operating procedures; (2) fails to maintain in good

or unenforceability shall not affect the validity or

working order such safety devices and guards; (3) alters

enforceability of the other portions hereof.

or modifies the Product in any way not approved by
StoneAge in advance in writing; (4) allows the Product to
be operated under more severe conditions or beyond the
rated capacity specified for the Product; or (5) otherwise
negligently operates the Product.

End-User shall

indemnify and hold StoneAge harmless from any and all
liability or obligation incurred by or against StoneAge,
including costs and attorneys’ fees, to or by any person
so injured.
TO THE FULL EXTENT ALLOWED BY APPLICABLE
LAW, STONEAGE SHALL NOT BE LIABLE FOR ANY
INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL,
OR PUNITIVE DAMAGES (INCLUDING WITHOUT
LIMITATION, LOSS OF PROFITS, LOSS OF GOODWILL,
DIMINUTION OF VALUE, WORK STOPPAGE,
INTERRUPTION OF BUSINESS, RENTAL OF
SUBSTITUTE PRODUCT, OR OTHER COMMERCIAL
LOSS EVEN TO THE EXTENT SUCH DAMAGES WOULD
CONSTITUTE DIRECT DAMAGES), WITH RESPECT TO
THE COVERED STONEAGE PRODUCT, OR OTHERWISE
IN CONNECTION WITH THIS LIMITED WARRANTY,
REGARDLESS OF WHETHER STONEAGE HAS BEEN

866-795-1586 • WWW.STONEAGETOOLS.COM

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Language                        : en-US
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c145 79.163499, 2018/08/13-16:40:22
Create Date                     : 2019:02:26 12:27:09-07:00
Metadata Date                   : 2019:02:26 12:27:16-07:00
Modify Date                     : 2019:02:26 12:27:16-07:00
Creator Tool                    : Adobe InDesign CC 14.0 (Windows)
Instance ID                     : uuid:2f347c74-2404-49d0-8a23-b61e1e98aea4
Original Document ID            : xmp.did:9d322ba9-59f6-4fd3-b672-f1a11ffe25b4
Document ID                     : xmp.id:54d5d2fc-842a-c047-bf4a-817bdd2fa01a
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:6aedc1bb-e057-d44e-b118-2284da0d77e6
Derived From Document ID        : xmp.did:6aedc1bb-e057-d44e-b118-2284da0d77e6
Derived From Original Document ID: xmp.did:9d322ba9-59f6-4fd3-b672-f1a11ffe25b4
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 14.0 (Windows)
History Changed                 : /
History When                    : 2019:02:26 12:27:09-07:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 24
Creator                         : Adobe InDesign CC 14.0 (Windows)

EXIF Metadata provided by EXIF.tools

Bn Manual

Navigation menu

Versions of this User Manual:

Views

Navigation