Cavins Cat 2012 T 4839 Ci Web

User Manual: T 4839 Ci

Open the PDF directly: View PDF .
Page Count: 32

Manufacturer of original design quality well servicing products

OIL WELL TOOLS

A Division of DAWSON ENTERPRISES

CAVINS “ADVANCE” AUTOMATIC

SPIDERS

For Casing-Tubing and Drill Pipe

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

The “Advance” Spider developed by Cavins Oil Well Tools is

considered to be the pioneer in power slips. Through years of

experience and testing, many improvements have been made

which make the Cavins “Advance” Spider the leader for a safe,

economical, and trouble-free handling of tubular goods. Heat treat-

ed alloy steel is used throughout for the greatest possible strength

and the longest wearing life with a minimum of weight. The shafts

are hardened alloy steel for longer life. Replaceable steel bushings

are fitted into the journal bearings. All bearings and journals are

equipped with grease fittings for lubrication. Air Cylinders and Foot

Valves are mist lubricated through the airstream. All Cavins

“Advance” Spiders are equipped with a manually operated safety

latch which may be used to positively lock the slips in their set

position. Because of the low operating pressure the slips cannot

release from the tubing until it has been raised by the elevators,

thus guarding against a lost string in the event that the Foot Valve

is tripped accidentally. The Slips, Shafts, and Air Operating

Mechanisms are protected by guards to prevent damage caused

by the elevators or other outside forces. Through research and

field testing our engineers are constantly on the look out for addi-

tional improvements which will assure the personnel in the field of

receiving the safest and most maintenance free equipment that is

available.

The Cavins “Advance” Spider is available in five models, Model

“B”, “C”, “C-HD”, “F”, and “G”. All are designed for manual, com-

pressed air, or hydraulic operation with the exception of the Model

“G” which is available for compressed air or hydraulic operation

only.

All Cavins “Advance” Spiders may be used on a rotary table

with an adapter plate that fits into the square drive or pin drive

master bushing, centering the Spider on the rotary table. This also

permits the manually operated Spider to be rotated.

Models “B”, “C”, and “C-HD” Spiders may be equipped with a

Gate and Slips which are relieved to pass parallel strings of tub-

ing. If the Spider is to be used with both single and parallel strings

to any extent, it is recommended that both kinds of Slips and

Gates be ordered. A standard feature of all Cavins “Advance”

Spiders is a specially designed Gate Section which will allow the

running of an electric submersible pump cable simultaneously with

any size tubing string.

OIL WELL TOOLS

CAVINS “ADVANCE” SPIDERS

SPECIFICATIONS MODEL “B” MODEL “C” MODEL “CHD” MODEL “F” MODEL “G”

HEIGHT 15-1/2” 16-1/2” 16-1/2" 26-3/4" 35"

BASE DIMENSION 14" X 17" 16-1/2" X 18-1/2" 16-1/2" X 18-1/2" 28" X 28" 41" X 41-5/8"

GATE OPENING 4-1/4" 5-3/4" 5-3/4" 8-3/4" 13-3/4"

BOWL OPENING 4-3/4" DIA. 6-1/2" DIA. 6-1/2" DIA. 10-1/8" DIA. 15-1/2" DIA.

TUBULAR RANGE 1.315" to 3-1/2" 1.315" to 5-1/2" 1.315" to 5-1/2" 2-3/8" to 8-5/8" 2-3/8" to 13-3/8"

MAXIMUM LOAD 55 Tons 82.5 Tons 125 Tons 200 Tons 350 Tons

CAPACITY 110,000 Lbs. 165,000 Lbs. 250,000 Lbs. 400,000 Lbs. 700,000 Lbs.

Fig. 1

Air operated “Advance” Model “C” Spider with full circle

replaceable inserts.

Fig. 2

Advance Mode “B” Spider (hand operated)

CAVINS “ADVANCE” SPIDERS

MODEL “F” AND “G”

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

The CAVINS “Advance” Model “F” Automatic Spider is another

industry tested and proven tool. Similar to the Model “B” and Model

“C” Spiders, the Model “F” offers manual, pneumatic(air) or

hydraulic operation mechanisms. The Model “F” Spider (Fig. 1) can

handle tubular goods ranging in size from 2-3/8" O.D. through 8-

5/8" O.D. and is favored for automation in light drilling operations

or for heavy workover and production rigs. The load capacity for

the Model “F” Spider is 400,000 lbs. NOW the Model “F” Spider is

available also with CAVINS patented, Type “FCR” Full Circle Slips,

(Fig. 2) with Replaceable Type “FCI” Inserts. The conventional,

Type “TD” Slips, (Fig. 3) with Replaceable Inserts are also avail-

able.

For heavy drilling operations, up to 700,000 pounds (350 tons)

hook load capacity; the CAVINS “Advance” Model “G” Automatic

Spider, (Fig. 4) is recommended where heavy duty, dependable

service applies. The Model “G” Spider will handle tubular goods

ranging in size 2-3/8" through 13-3/8" O.D. and is available for

pneumatic (air) or hydraulic operation. Like all CAVINS “Advance”

Spiders, the Model “G” utilizes a minimum of moving parts for ease

of operation and very minimal maintenance. CAVINS patented and

proven Type “FCR” Full Circle Slips (Fig. 2 and 5) with replaceable

Type “FCI” Inserts, are used for the complete range of sizes in the

Model “G” Spider. The long 16" gripping area plus 360˚ degree,

100% contact of the Type “FCI” Inserts, makes it the most positive

pipe holding device of its kind. Competition can boast only a max-

imum of 70% contact of the pipe. The clear advantage being

greater contact area causing far less chance of damaging or

crimping heavy strings of pipe. Another proven asset of the

CAVINS unique design is that there is no need for costly pipe

guides to attach to the spider because the Slips and Inserts with-

draw completely from the Spider Bowl and when disengaged

allows full protection from damage by the string when it is in

motion.

OIL WELL TOOLS

MODEL “F” SPIDERS AFFORD MANUAL, PNEUMATIC, and HYDRAULIC OPERATION

MODEL “G” SPIDERS FOR HEAVY DRILLING OPERATIONS

Fig. 2

“FCR” Type, Full Circle

Slips, available with “FCI”

Replaceable Inserts.

Fig. 1

Cavins Model “F” Spider, the long time favorite for dependable service now

meets the cost conscious production criteria with Full Circle Slips that fea-

ture replaceable “FCI” Inserts.

Master Slip Bodies with companion

Replaceable Inserts afford the

greatest economy for working a

wide range of tubular goods sizes.

Fig. 3

“TD” Type, Conventional

Slips, available with

Replacement Inserts.

Fig. 4

Fig. 5

CAVINS INVERTED SPIDERS

FOR “SNUBBING” OPERATIONS

U.S. Pat. #2,846,877

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

Hydraulic work over (Snubbing) services are increasingly

favored, having the advantage of eliminating the need to kill

the well. It lowers the cost as well as the time and problems

associated with circulating salt water, mud and other fluids.

The Cavins “Advance” Model “C,” “C-HD,” and “F” Spiders

have specifically been designed for snubbing operations. It

can work in its right side up position (Fig. 2) or in the inverted

upside down position (Fig. 1). The Spider Body and Slips are

specially designed for this service. The gripping Inserts how-

ever, are of standard design and are interchangeable with the

regular Cavins Spiders. Tubular Goods from 1.315" (1" O.D. to

5-1/2" O.D. can be handled with a clear opening for 6.050"

O.D. casing coupling with the Model “C” and “C-HD” Spiders.

Tubular goods 2-3/8" O.D. to 8-5/8" O.D. can be run with the

Model “F” Spider. All Spider models can be either hydraulic or

compressed air operated. A minimum of moving parts

assures a trouble-free operation.

A typical set of spiders on a snubbing rig is illustrated in

Fig. 3. Four spiders may be used: two (2) in the regular

(upright) position and two (2) in the inverted (snubbing) posi-

tion. One regular and one inverted spider are stationary and

the other regular and inverted spiders are mounted on the

traveling piston. The traveling spiders are used to either push

the pipe into the well or pull it from the well while the station-

ary spiders are used to hold the string of pipe when the trav-

eling spiders are not engaged.

OIL WELL TOOLS

Fig. 2

A Cavins Inverted

Spider and Regular

Spider in opposing

positions for hydraulic

work over (snubbing)

operation.

Fig. 1

Fig. 3

A typical snubbing operation employing two inverted spiders and two regular

(upright) spiders.

Fig. 4

Cavins Model “C-HD” Spiders will handle tubular goods in a size range

of 1" to 5-1/2" O.D. with a maximum load capacity of 250,000 pounds

WORKBASKET FOR

MEN & EQUIPMENT

TRAVELING SPIDERS

A INVERTED

B REGULAR

STATIONARY SPIDERS

C INVERTED

D REGULAR

[ CLOSED ]

[ OPEN ]

TRAVELING PISTON

TRAVELING

PISTON

HYDRAULIC CONTROL FLUID

INLET AND OUTLET

HOSE CONNECTIONS

[ OPEN ]

[ CLOSED ]

“FULL CIRCLE” SLIPS

REMOVABLE INSERTS

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

CAVINS

“ADVANCE”

SPIDERS

The Cavins “Full Circle” Slips,

(Type “FCR”) with removable inserts

were designed to replace Full Circle

Slips with integral teeth. The “FCR”

Full Circle Slips surround the pipe

360 degrees and exert a uniform grip-

ping power on the pipe to avoid defor-

mation, bottle-necking, or crushing. A

heavy-duty steel pin retains each insert

securely in each slip body segment. The cot-

ter key secures the retaining pin in place.

THREE DISTINCT ADVANTAGES ARE REALIZED WITH THIS NEW DESIGN:

1. It eliminates the purchase of individual slips for every size of tubular goods.

2. The Slip Body is made of tough alloy steel for maximum strength while the

inserts are of case hardened steel for longer wear.

3. Since only a minimum of Slip Bodies are required to cover the range of

tubular goods for each spider, the investment compares less than it would

with the purchase of individual slips for each size pipe.

For the Cavins “Advance” Model “B” Spider, only one type “FCR” Slip

Body is required, with removable inserts, (TYPE “FCI”). One set of (4) inserts

is required for each size of Tubular Goods:

The 2-7/8", Type “FCR” Master Slip Body takes inserts for 2-7/8", 2-

3/8", 2-1/16", 1.900 (1-1/2"), 1.660 (1-1/4"), and 1.315 (1") O.D. tubular

goods.

To handle 3-1/2" O.D. Tubing, it is necessary to use a Type “TD” Slip

Body with either Chevron, (Type “CI”) Replaceable Inserts or button

(Type “CBI”) Replaceable Inserts.

For the Cavins “Advance” Model “C” and “C-HD” Spiders, three (3)

types of “FCR” Slip Bodies are available with Removable Inserts, (Type “FCI”).

One set of (4) inserts is required for each size of Tubular Goods:

The 2-1/16",Type “FCR” (-1) Master Slip Body takes Inserts for 2-1/16",

1.900" (1-1/2"), 1.660" (1-1/4") and 1.315 (1") O.D. Tubular Goods.

The 3-1/2" Type “FCR” (-2) Master Slip Body takes Inserts for 3-1/2",

2-7/8", and 2-3/8" O.D. Tubular Goods.

The 4-1/2" Type “FCR” (-3) Master Slip Body takes Inserts for 4-1/2",

4", and 3-1/2" O.D. Tubular Goods.

For the Cavins “Advance” Model “F” Spider, three (3) Type “FCR”

Master Slip Bodies are available with Removable Inserts, (Type “FCI”). One set

of (4) inserts is required for each size of Tubular Goods:

The 3-1/2" Type “FCR” Slip Body takes Inserts for 3-1/2", 2-7/8", and

2-3/8" O.D. Tubular Goods.

The 5-1/2" Type “FCR” Master Slip Body takes Inserts for 5-1/2", 5",

4-1/2", and 4" O.D. Tubular Goods.

The 7-5/8" Type “FCR” Master Slip Body takes Inserts for 7-5/8", 7",

and 6-5/8" O.D. Tubular Goods.

For the Cavins Model “G” Spider, six (6) Type “FCR” Master Slip Bodies

are available with Removable Inserts, (Type “FCI”). One set of (8) inserts is

required for each of two larger sizes of Tubular Goods and one set of (4)

inserts each for the other sizes:

The 3-1/2" Type “FCR” Master Slip Body takes Inserts for 3-1/2", 2-

7/8", and 2-3/8" O.D. Tubular Goods.

The 5-1/2" Type “FCR” Master Slip Body takes Inserts for 5-1/2", 5",

4-1/2" and 4" O.D. Tubular Goods.

The 7-5/8" Type “FCR” Master Slip Body takes Inserts for 7-5/8", 7",

and 6-5/8" O.D. Tubular Goods.

The 9-5/8" Type “FCR” Master Slip Body takes Inserts for 9-5/8" and

8-5/8" O.D. Tubular Goods.

The 11-3/4" Type “FCR” Master Slip Body takes Inserts for 11-3/4"

and 10-3/4" O.D. Tubular Goods.

The 13-3/8" Type “FCR” Master Slip Body takes Inserts for 13-3/8"

O.D. Tubular Goods.

OIL WELL TOOLS

Full Circle Slip Inserts are available for Cavins “Advance” Spiders, Models

“B”, “C”, “C-HD”, “F”, and “G”

with patented

360°

degree

FULL CIRCLE SLIPS

Type “FCR”

PATENTED

CAVINS Model “C”

“Advance” Spider

SPIDERS ACCESSORIES

FOR MODELS “B,” “C,” “F” AND “G” SPIDERS

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

The Foot Operated Air Control Valve

only is available in a safety cover guard

(Fig. 1). A combination unit is offered

where it is desirable to have the Foot

Valve and the Filter, Regulator and

Lubricator all in one steel case, (Fig. 2)

High pressure (300 P.S.I.) air hoses

with Female Quick Change Connectors

can be supplied in any desired length

(Fig. 3).

Air Filter, (Fig. 4), with Drain (A),

Pressure Regulator with Gauge (B) and

Lubricator (C) assembled into one unit

and supplied with Quick Change Air

Coupling and Mounting Bracket. This unit

can be installed near the Operator’s stand

or under the console. When the rig is

working in extremely high temperature

areas, metal bowls can be supplied in

place of the plastic ones normally fur-

nished on the Filter and Lubricator.

When using the Cavins “Advance”

Spider on a drilling rig for making round

trips, a Rotary Table Master Bushing

Adapter Plate is available which is bolted

to the bottom flange of the Spider. The

Adapter Plate fits into any standard A.P.I.

square drive (Fig. 5) or Pin Drive Master

Bushing (Fig. 6).

“FULL CIRCLE”

SLIPS

with

REPLACEABLE

INSERTS

The Cavins Full Circle Slip with Removable inserts has been

designed to replace the Integral Full Circle Slip. The new style, type

“FCR” Slip, consists of (4) slip segments, as do all other types of

Cavins Slips. It has the great advantage that the Full Circle Inserts

are replaceable. The Slip Body is made of tough high grade heat

treated alloy steel. The Inserts are also alloy steel, case hardened.

Three Master Slip Bodies are available for the Model “C” Spider.

One Master Slip Body is available for the Model “B” Spider.

OIL WELL TOOLS

Type “TD” Slips with replace-

able inserts for Model “B” and

Model “C” Spiders. Circular

Button Type Inserts are rec-

ommended for light loads.

Available for either single or

parallel strings. (Fig. 7)

Type “TD” Slips with

replace-

able “Chevron” inserts

. Inserts

have 35% greater contact than

the Circular Button type.

Recommended for the heavier

tubular string load. Available

for either single or parallel

strings operation. (Fig. 8)

(Fig. 2)

Combination Foot Valve. Pressure

Regulator with Gauge and Lubricator,

mounted in Portable Carrying Case.

(Available with Ratchet or Piston Type

Foot Valve).

(Fig. 1) PISTON TYPE TB230

Foot-Operated Valve with Safety Cover

Guard and Hose Connections.

(Fig. 1B) RATCHET TYPE TB200

Foot-Operated Valve, Ratchet-Type

with Safety Guard Cover and Hose

Connections.

(Fig. 4)

Air Filter, Pressure Regulator with

Gauge, and Lubricator Unit. TB400

(Fig. 3)

Oil-Resistant Air Hose with Female

Quick Change Couplings.

(Fig. 5)

Rotary Table Master Bushing Adapter

Plate for Square Drive.

(Fig. 6)

Rotary Table Master Bushing Adapter

Plate, Pin Drive.

TB220 with Ratchet Type

TB220-P with Piston Type

TUBING SPIDERS

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

CONVERTIBLE TUBING SPIDERS

50 TON AND 100 TON

Description:

These versatile tubing spiders can

easily be converted from power to man-

ual operation. For power operation, an

air cylinder actuates unitized slips. The

spiders can be quickly converted to

manual operation by substituting a foot

pedal and foot release lever assembly

for the air cylinder.

Options such as guard doors are

available. Cavins/BJ fine-tooth slip

inserts are available in most assembly

sizes and are recommended to reduce

tooth penetration. As a power tool, the

convertible tubing spider can operate

off the regular rig air system or from an

auxiliary trailer-mounted air compres-

sor unit.

50 TON MODEL:

Tubing size capacity is 1.315"

through 3-1/2" (33.40 mm - 88.90 mm)

O.D. The slips provide a full 6" (152.40

mm) of vertical gripping length around

the tubing to prevent pipe crimping. The

50-ton model provides a 5-1/2" (139.70

mm) opening through the bowl.

Available in air or manually operated

models.

100 TON MODEL:

Tubing size capacity is 2-3/8"

through 3-1/2" (60.33 mm - 88.9 mm)

O.D. The slips provide a full 9" (228.60

mm) of vertical gripping length around

the tubing to prevent pipe crimping. The

100-ton model provides a 5-7/8"

(149.23 mm) opening through the bowl.

SPECIFICATIONS – FOR 50-TON CONVERTIBLE TUBING SPIDERS

TYPES 50-A (AIR) AND 50-M (MANUAL)

Part Weight Ea.

gkbl.oNnoitpircseD

Type 50-A Air-Operated Tubing Spider with Plain Door,

Less Slips, Hoses and Control Assembly 29660 173 78

Type 50-A Air-Operated Tubing Spider with Guard Door,

Less Slips, Hoses and Control Assembly 29659 193 87

Type 50-M Manually Operated Tubing Spider with

3571126692spilS sseL ,rooD nialP

Type 50-M Manually Operated Tubing Spider with

2673116692spilS sseL ,rooD drauG

OIL WELL TOOLS

50 Ton Convertible Tubing Spider

HOSE ASSEMBLIES WITH FITTINGS FOR ALL TUBING SPIDERS

Part Weight Ea.

gkzo–bl.oNnoitpircseD

Air Line Hose Assembly (1/4" x 12'–6.35 MM x 3.66 m)–

28–494003deriuqer 1 ,lortnoC ot ylppuS riA

Air Line Hose Assembly (1/4" x 12'–6.35 mm x 3.66 m)–

28–466303deriuqer 2 ,redipS ot lortnoC

Air Line Hose Assembly (1/4" x 15'–6.35 mm x 4.57 m)–

3.2551-94003deriuq

er 1 ,lortnoC ot ylppuS riA

Air Line Hose Assembly (1/4" x 15'–6.35 mm x 4.57 m)–

3.2551-66303deriuqer 2 ,redipS ot lortnoC

Air Line Hose Assembly (1/4" x 25'–6.35 mm x 7.62 m)–

2.3752-94003deriuqer 1 ,lortnoC

ot ylppuS

Air Line Hose Assembly (1/4" x 25'–6.35 mm x 7.62 m)–

2.3752-66303deriuqer 2 ,redipS ot lortnoC

CONTROL ASSEMBLIES FOR AIR SPIDERS

Part Weight Ea.

gkzo–bl.oNnoitpircseD

Standard Air Control Assembly complete with single pedal

control valve with base plate and fittings 30362 31–4 14

Air Control Assembly complete with single pedal control

valve with base plate and fittings, filter, lubricator,

720–0646303revoc dna egag htiw rotaluger

SPECIFICATIONS – FOR 100-TON CONVERTIBLE TUBING SPIDER

TYPES 100-A (AIR) AND 100-M (MANUAL)

Part Weight Ea.

gkbl.oNnoitpircseD

Type 100-A Air-Operated Tubing Spider with Guard Door,

Less Slips, Hoses and Control Assembly 37841 257 115

Type 100-M Manually Operated Tubing Spider with

Guard Door, Less Slips, Hoses and Control Assembly 37843 200 91

SLIP ASSEMBLIES FOR TYPES 50-A (AIR) AND 50-M (MANUAL)

TUBING SPIDERS

Part Slip Weight Ea.

gkbl.ytQ.oN tresnI.oNnoitpircseD

1.315" (33.40 mm) O.D. Slip Assembly 29773 29259 6 50 23

1.660" (42.16 mm) O.D. Slip Assembly 29772 29258 6 49 22

1.900" (48.26 mm) O.D. Slip Assembly 29771 29257 6 48 22

2"-2-1/16" (50.8 mm-52.39) O.D. Slip Assembly

29770 29256 6 46 21

2-3/8" (60.33 mm) O.D. Slip Assembly 29769 29255 6 39 18

2-7/8" (73.03 mm) O.D. Slip Assembly 29693 24773 6 38 17

3-1/2" (88.9 mm) O.D. Slip Assembly 29692 24774 12 37 17

SLIP ASSEMBLIES FOR TYPES 100-A AND 100-M

TUBING SPIDERS

Part Insert Weight Ea.

gkbl.ytQN/P.oNnoitpircseD

2-3/8" (60.33 mm) O.D. Slip Assembly 35110 29255 9 45 20

2-7/8" (73.03 mm) O.D. Slip Assembly 35111 24773 9 45 20

3-1/2" (88.9 mm) O.D. Slip Assembly 35112 24774 18 45 20

*All except 3-1/2" (88.9 mm) Slip Assembly are made out of 2-7/8" (973.03 mm) Slip Bodies.

TUBING SPIDERS

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

TS-100 TUBING SPIDER

The Baash-Ross TS-100 Tubing

Spider is available in two body sizes for

running a wide range of tubing sizes.

The 3-1/2" Tubing Spider accommo-

dates single or dual strings of tubing.

When running single strings, the spider

will handle any size tubing up thru 3-1/2"

O.D. When running dual strings, the main

tube, which is held by the slips, can be

any size from 1.050" O.D. thru 3-1/2"

O.D. and the auxiliary tube can be any

size up thru 1.660" O.D.

The 5-1/2” Tubing Spider can handle

single, double, or triple strings. When

running single strings the spider will han-

dle from 3-1/2” up to 5-1/2” O.D. tubulars.

When running dual strings, the main

tube, which is held by the slips, can be

from 3-1/2” thru 5-1/2” O.D. and the aux-

iliary tube can be any size up to 1.900”

O.D. When running triple strings the main

tube is 3-1/2” O.D. and the auxiliary tubes

can be any size thru 1.900” and 1.660”

O.D. respectively.

Each body section is recessed to hold

liner segments so stresses of supporting

the tubing are transmitted directly to the

slip body. The liner segments can be

replaced by removing a single pin and

sliding out the segments.

The latch automatically locks the slips

around the tubing as the handles are

closed. The latch opens when the opera-

tor spreads the handles. The spider bowl

is made in two halves, fastened together

by a hinge pin and removable lock pin.

This design combines strength with ease

of operation and removal.

For running a single string of tubing,

both halves of the bowl are smooth-

bored and identical. For a double string,

or triple string, one half of the bowl is

smooth-bored while the other half is slot-

ted to receive the auxiliary tube or tubes.

The bowl will fit directly into a API stan-

dard square in the rotary table, or it can

be bolted to a wellhead flange thru the

slots provided.

OIL WELL TOOLS

3-1/2" TS 100 TUBING SPIDER

3-1/2" Complete with slip liners & bowl

O.D. Single string Double string

tWtWeziS

Inches Part no. Lbs Part no. Lbs

Bowl only 7502-100 168 7502-101 166

Complete

1.050 7502-100-H 237 7502-101-H 235

1.315 7502-100-A 235 7502-101-A 233

1.660 7502-100-B 234 7502-101-B 233

1.900 7502-100-C 232 7502-101-C 230

2.000 7502-100-J 230 7502-101-J 228

2-1/16 7502-100-G 228 7502-101-G 226

2-3/8 7502-100-D 226 7502-101-D 224

2-7/8 7502-100-E 225 7502-101-E 223

3-1/2 7502-100-F 223 7502-101-F 221

5-1/2" TS 100 TUBING SPIDER

5-1/2" Complete with slips, tong & bowl

O.D. Single string Double string* Triple string**

tWtWtWeziS

Inches Part no. Lbs Part no. Lbs Part no. Lbs

Bowl only 7502-103 200 7502-105 7502-106

Complete

3-1/2 7502-103-A 300 7502-105-A 300 7502-106-A 300

4 7502-103-B 284 7502-105-B 284

4-1/2 7502-103-C 275 7502-105-C 275

4-3/4 7502-103-D 270 7502-105-D 270

5 7502-103-E 264 7502-105-E 264

5-1/2 7502-103-F 253 7502-105-F 253

SLIPS FOR 5-1/2" TS-100 TUBING SPIDERS

Single string Double string* Triple string**

O.D. Size No. Total Total Total

Inches Req’d. Part no. Wt Lbs Part no. Wt Lbs Part no. Wt Lbs

Tong Assy. 1 7502-70 29 7502-78 29 7502-107 29

Slips

5-1/2 4 7502-A-26 49 7502-A-106 49

5 4 7502-D-26 60 7502-D-106 60

4-3/4 4 7502-B-26 66 7502-B-106 66

4-1/2 4 7502-C-26 71 7502-C-106 71

4 4 7502-G-26 80 7502-G-106 80

3-1/2 4 7502-F-26 96 7502-F-106 96 7502-A-222 96

2-7/8 4 7502-H-26 116

2-3/8 4 7502-K-26 132

SLIP LINERS FOR 3-1/2" TS-100 TUBING SPIDERS

Single String and Double String*

latoT.oNeziS .D.O

Inches Req’d. Part no. Wt Lbs

Slip Assy 1 7502-104 43-3/4

3-1/2 9 7502-A-5069 11-1/4

2-7/8 9 7502-A-5070 13-1/2

2-3/8 9 7502-A-5071 14-5/8

2-1/16 9 7502-A-5072 18

2.000 9 7502-A-5073 19-1/8

1.900 9 7502-A-5074 20-1/4

1.660 9 7502-A-5075 22-1/2

1.315 9 7502-A-5076 23-3/8

1.050 9 7502-A-5077 13-1/2

*UP TO AND INCLUDING 3-1/2" X 1.660"

Baash-Ross is a licensed trademark of

National Oilwell Varco, L.P.

* Up to and including 5-1/2" x 1.900"

**3-1/2" x 1.900" x 1.660"

TS 100

TUBING SPIDERS

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

BAASH-ROSS®Open End Tubing Spiders

The Open End Tubing Spider is available in two basic sizes;

one to accommodate slips for 3-1/2" O.D. tubing or smaller,

and the other to handle 4-1/2" O.D. tubing or smaller.

It is placed around the tubing by lifting out a removable end

gate, sliding the bowl into place and dropping the end gate

back into position, where it is locked with a bolt.

The spider is made of heat-treated steel and is rated at 100-

ton capacity.

The four-slip segments of the tubing spider are firmly hung

to a hinged tong by dovetail grooves in their backs which mate

with tongues inside the tong body.

An automatic tong latch for locking the slips in position can

only be opened by the handles.

The slips are 10" long and provide a large gripping area.

Because they set as a unit, slip pressure is uniform at all

points. Narrow slip backs eliminate sticking and compensate

for wear of the spider body.

TABLE NO. 1

3-1/2" Open End Tubing Spider Complete (Double String)

2", 2-1/2" or 3" production tube with 1-1/4" power tube

(the slips hold production tube only)

Power Tubing Spiders

WEB WILSON®Model PM Power Tubing Spiders

These power spiders are available to handle the following

tubing sizes: 1.315", 1.660", 1.900", 2", 2-1/16", 2-3/8", 2-7/8",

and 3-1/2". Only two sizes of slips (bodies) are required for

handling tubing up to 3-1/2" O.D.

One size slip will handle tubing from 1.315" O.D. to 2-7/8"

O.D. equipping with proper size insert. The other size slip han-

dles 3-1/2" O.D. using the 3-1/2" insert.

Two spider types are available: hydraulic and pneumatic.

Both are rated 50-ton maximum capacity. Pneumatic spiders

operate on air pressure from 40 to 50 psi. Hydraulic powered

spiders operate on maximum recommended working pressure

of 150 psi.

A hinged door permits installation without “stripping” over the

tubing. Slip inserts are easily changed from one size to anoth-

er; interchangeable inserts permit the assembly to work for

many tubing sizes.

The slip inserts are carefully machined from steel alloy.

To order — Specify: (1) Tubing Spider, Power. (2) Part number.

(3) Hydraulic or pneumatic. (4) Tubing size. (5) Optional equipment.

Baash-Ross and Web Wilson are licensed trademarks of

National Oilwell Varco, L.P.

FIG. 1 – The Open End Tubing Spider, complete, show-

ing Unitized Slip Assembly set in Body.

TABLE NO. 2

4-1/2" Open End Tubing Spider Complete (Double String)

2-1/2" production tube with 1-1/4" power tube,

3" production tube with 1-1/2" power tube

(the slips hold production tube only)

To order — Specify: (1) Spider Open End. (2) Part numbers.

(3) Size of body or bowl (3-1/2" or 4-1/2"). (4) If single or double

strings.

TABLE NO. 3

WEB WILSON Model “PM” Power tubing Spider

50-Ton Capacity

OIL WELL TOOLS

Nom. Tubing Size to Hold

with Power Tube 2" x 1-1/4" 2-1/2" x 1-1/4" 3" x 1-1/4"

API Tubing Size to Hold

with Power Tube 2-3/8" x 1.660" 2-7/8" x 1.660" 3-1/2" x 1.660"

Wt. Per Set Complete lbs. 218 220 225

Part Number Complete 7502-67-A 7502-67-B 7502-67-C

Wt.,

Part Lbs.

hcaErebmuNnoitpircseD

Air Operated Spider Complete w/Control Assembly

and Hoses w/Slip Bodies to Hold:

1525905-9258)stresnI sseL(.D.O "8/7-2–"513.1

1527905-9258)stresnI sseL(.D.O "

2/1-3

Hydraulically Operated Spider Complete w/Control

Assembly and Hoses w/Slip Bodies to Hold:

9526905-9258)stresnI sseL(.D.O "8/7-2–"513.1

9528905-9258)stresnI sseL(.D.O "2/1-3

Nom. Tubing Size to Hold with Power Tube 2-1/2" x 1-1/4" 3" x 1-1/2"

API Tubing Size to Hold with Power Tube 2-7/8" x 1.660" 3-1/2" x 1.900"

912822.sbl etelpmoC teS reP.tW

Part B-56-2057A-56-2057etelpmoC rebmuN

AIR HOSE

COMPLETE

FOOT VALVE ASSY.

AIR SUPPLY HOSE

COMPLETE

FRONT VIEW OF SPIDER

WITH GUARD ASSY.

POWER TONGS

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

HYDRATORC®POWER TUBING TONGS

These part numbers are for power tongs complete less jaws and bushings, less

hoses and quick-connect couplings.

These part numbers are for power tongs complete with high-torque duty motor

less jaws and bushings, less hoses and quick-connect couplings.

SUPER-POWAIRMATIC®POWER TONGS

These part numbers are for power tongs complete less jaw and bushing, less

hoses and quick-connect couplings.

Hydratorc and Super-Powairmatic are licensed trademarks of

National Oilwell Varco, L.P.

RS HYDRAULIC TUBING TONG

Description:

The Model RS is a gate-type tong that

incorporates a four way control valve to

reverse the tong without roll-over.

This reversible model does not include a

positioner and uses stiff arm installation.

As an option, the Model RS is available

with positioner and a roll-over hanger.

Operational features:

Can deliver and maintain 12 HP (8.95 kw)

continuously when required without over-

load or strain. The control valve can be

operated from either front or rear control

levers. The heavy-duty transmission han-

dles high torque without overload or

strain. Quick change jaw and bushing

assemblies accommodate curved face

dies as well as straight dies. Choice of

standard or high-torque motor.

Size range:

1.050"-4-1/2" (26,7-114,3 mm)

BTS REVERSIBLE SHORT LEVER,

GATE TYPE HYDRAULIC

POWER TONG

Description:

The BTS combines the greater horse-

power speed and torque of other

Cavins/BJ power tubing tongs. In addi-

tion, the model BTS has special space-

saving qualities for smaller rigs used for

slim hole production and workover jobs.

The overall saving in length totals 10"

(254 mm).

Size range:

1.050" to 4-1/2" (26,7-114,3 mm)

CTS REVERSIBLE, STANDARD LENGTH

GATE-TYPE TUBING AND CASING TONG

Description:

Similar to the Model RS except that the front end

has been modified to handle pipe from 2-3/8" tub-

ing to 5-1/2" casing. Quick-change jaws and bush-

ing assemblies take either curved or straight dies.

Size range: 2-3/8" to 5-1/2" (60,3-139,7 mm)

Specifications RS, BTS, CTS Tongs:

SA REVERSIBLE, STANDARD-LENGTH,

GATE-TYPE, AIR POWERED TONG

Description:

High-Torque vane-type 9 HP (6,7 kw) air motor.

Fully enclosed heavy-duty transmission handles

high torque without overload or strain. Positive

front-end chain drive. Four way valve and manifold

provide reverse without roll-over. Also available as

BTA Model, retaining the same features as the SA

but having a 10" (254 mm) shorter length.

Size range: 1.050" to 4-1/2" (26,7-114,3 mm)

Specifications SA, BTA:

Model CH (not shown)

Closed head hydraulic powered tong with

reversible motor

Design Features: Jaws turn over to reverse tong.

Choice of standard or High Torque motor to pro-

vide desired torque. Five multiple-size-range jaws

are designed with convex die contact surfaces for

positive even pressure grip equally spaced around

the tubing circumference.

Operational Features: A tandem control valve

controls both tong operation and lift cylinder.

Balanced spring suspension for easy handling and

positioning. Torque valve adjusts tong torque to

tubing joint requirements.

Optional Equipment: Closed-Head Back-up;

Operator can choose either of two positions. He

can straddle couplings and make up both threads

on API tubing when going into hole or he can move

back-up closer to tong when gripping coupling.

Gripping system identical to Model CH tong but is

operated manually.

HOW TO ORDER TONGS COMPLETE

33135-7 “CH” Tong Complete with 2-3/8–3-1/2"

Jaw and Jaw Holder Assembly

33135-16“ CH” Tong Complete with 2-3/8"–3-1/2"

Jaw and Jaw Holder Assembly and High

Torque Motor

OIL WELL TOOLS

RS Tubing Tong

Rigid Hanger Less Positioner Roll-over Hanger with Positioner

W.aE thgieW.aE thgie

Model Part no. lbs kg Part no. lbs kg

RS 34891 580 263 34892 590 268

BTS 30072 650 295 30072-2 659 299

CTS 35089 580 263 35090 590 268

RS 34891-1 580 263 34892-1 590 268

BTS 30072-12 650 295 30072-11 659 299

CTS 35089-1 580 263 35090-1 590 268

SA 27550-2 572 259 27550 575 261

BTA 30580-2 652 266 30580 655 297

Standard Motor

High Torque Motor

Torque in Hi Gear, ft-lb

@ 2000 psi 1200 ft-lb 1700 ft-lb

(140 bar) (1627 Nm) (2305 Nm)

Torque in Lo Gear, ft-lb

@ 2000 psi 4650 ft-lb 6650 ft-lb

(140 bar) (6305 Nm) (9017 Nm)

Speed in Hi Gear, RPM @

30 GPM 83 RPM 68 RPM

(113.6 I/min)

Speed in Lo Gear, RPM @

13 GPM 21 RPM 18 RPM

(49.2 I/min)

Maximum Torque in Hi Gear. ft-lb @

150 psi (10.34 bar) 1660 ft-lb (2250 Nm)

Maximum Torque in Lo Gear, ft-lb @

150 psi (10.34 bar) 6500 ft-lb (8814 Nm)

Speed in Hi Gear, RPM 90 RPM

Speed in Lo Gear, RPM 24 RPM

OPTIONAL EQUIPMENT

FOR POWER TUBING TONGS

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

JAW AND BUSHING ASSEMBLIES–Hydratorc®Power Tongs

Models RS and BTS and Super-Powairmatic®Models SA and BTA

ON-OFF DEVICE FOR GATE-TYPE POWER TONGS

This air-operated tool increases tubing handling efficiency by

moving gate-type Hydratorc or Super-Powairmatic power tongs

onto or off the tubing automatically. Utilizes regular rig air source.

Power On-Off Device Complete with Standard Hand Control –

Part No. 29637-1 (Part No. 30237-Optional Foot Control).

SEMI-AUTOMATIC POSITIONER FOR GATE-TYPE

POWER TONGS

This optional feature consists of a control valve to line up the

opening accurately and quickly. The Semi-Automatic Positioner

can be included in any Hydratorc or Super-Powairmatic gate-

type power tong.

HOSES AND QUICK-CONNECT COUPLINGS

For Hydratorc®Power Tongs

FOR SUPER-POWAIRMATIC TONGS

CLOSED HEAD “CH” TONG

BACK-UP ATTACHMENT FOR CLOSED-HEAD “CH”

POWER TONG ONLY

thgieWtraPrebmuN

.sbLrebmuNemaN traPderiuqeR

2 1" x 15' Hydraulic Hose 991010-180 18

2461-920249gnilpuoC "1

Hydratorc and Super-Powairmatic are licensed trademarks of National Oilwell Varco, L.P.

.aE thgieWezis epiP Assembly Part Curved Straight

In. mm Type No. Face Die Die lb-oz kg

1.050 26.67 Jaw 23446-1 6472 6–0 2.72

1.050 26.67 Bushing 23447-1 6472 12–0 5.44

1.135 33.40 Jaw 29373-1 6473 6–0 2.27

1.315 33.40 Bushing 29374-1 6473 12–0 5.44

1.660 42.16 Jaw 29310-1 29313 5–12 2.61

1.660 42.16 Bushing 29307-1 29313 11–8 5.22

1.750 44.45 Jaw 29802-1 29313 5–9 2.52

1.750 44.45 Bushing 29801-1 29313 11–5 5.13

1.900 48.26 Jaw 29309-1 29312 5–4 2.38

1.900 48.26 Bushing 29306-1 29312 11–0 4.99

2 & 2-1/16 50.8 & 52.39

Jaw 29308-1 29311 5–0 2.27

2 & 2-1/16 50.8 & 52.39

Bushing 29305-1 29311 10–2 4.59

2-3/8 60.33 Jaw 27477-1 27494-1 4–12 2.15

2-3/8 60.33 Bushing 27645-1 27494-1 10–8 4.76

2-7/8 73.03 Jaw 27481-1 27498-1 4–8 4.76

2-7/8 73.03 Bushing 27660-1 27498-1 10–8 4.76

3-1/2 88.9 Jaw 17912-1 6473 4–8 2.04

3-1/2 88.9 Bushing 17913-1 6473 9–12 4.42

4 101.6 Jaw 23624-1 6473 4–0 1.81

4 101.6 Bushing 23623-1 6473 8–0 3.63

4-1/2 114.3 Jaw 24553-1 24554 3–0 1.36

4-1/2 114.3 Bushing 24552-1 24554 5–0 2.27

BACK-UP TONGS FOR GATE-TYPE POWER TONGS

Design Features: Cavins/BJ Type MS back-up tongs have

T-head latch with 3-jaw design and 2-step and 3-step lug jaw

construction to assure close grip on both coupling and tool

joint without adjustment.

HOW TO ORDER TONG COMPLETE

30430-110 “MS” Back-Up Attachment Complete with 2-3/8"

3.668 Lug Jaw Assembly

REPLACEMENT PARTS – “MS” BACK-UP ATTACHMENT

*No. Req’d for 4-1/2"–6-1/8" Range **Each Assy. Includes Lug Jaw & 6209 Die

OIL WELL TOOLS

thgieWtraP

).zo–.sbl(emaN traP.oN

30430 Back-Up Attachment Complete, Less Lug Jaw 47–0

(1.900"–2-1/16" & 2-3/8"–4-1/2")

31134 Back-Up Attachment Complete, Less Lug Jaw 53–14

(4-1/2"–6-1/8")

Number Part Weight

).zo–.sbl(emaN.oN traPderiuqeR

1 34314-1 1.900"–2-1/16" Lug Jaw Assembly** —

1 30422-6 2-3/8"–3.668" Lug Jaw Assembly** 6—0

1 30424-6 3-1/2"–4-1/2" Lug Jaw Assembly** 7—14

1 33917-6 4-1/2"–5-1/4" Lug Jaw Assembly** —

1 31139-6 5.200"–6-1/8" Lug Jaw Assembly** 4—8

1 6267 1.900"–4-1/2" Short Jaw 2—0

1 31130 4-1/2"–6-1/8" Short Jaw 2—0

1 31135 4-1/2"–6-1/8" Latch Jaw 2—0

1 (2*) 5206 1.900"–4-1/2" Latch Spring 0—2

2 (3*) 13494 1.900"–4-1/2" Hinge Pin 0—6

4 (5*) 939672-18 1.900"–4-1/2" Cotter Pin 0—1

1 28622-5 Outer-Inner Sleeve Assembly 23—0

(1.900"–6-1/8")

1 28622 Outer Sleeve 13—0

1 28623 Inner Sleeve 10—0

2 945031-64 Suspension Spring 0—4

1 30591 Leveling Screw 0—3

10—8reveL42682

18—1hctaL1-27503

12—0gnirpS waJ gnoL37503

12—0gnirpS waJ trohS47503

27—0niP egniH reveL57503

1 30421-1 Long Jaw Assembly** 12—0

2 30359 Toggle Pin (Long) w/Chain 1—0

1 30359-1 Toggle Pin (Short) w/Chain 0—8

23—0eiD gnoT9026

thgieWtraPrebmuN

.sbLrebmuNemaN traPderiuqeR

1 3/4" x 50' Air Hose Assembly 950123-3802 34

1 1" x 50' Air Hose Assembly 950124-3803 43

NO. 1-5/16– 2-3/8– 3-1/16– 4– 5–

COMPONENTS Req’d 2-1/16 3-1/2 4 4-3/4 6-1/16

Back-Up Assy. 1 32947 32947 32947 33647 33647

Back-Up Jaw Assy. 5 33706 33707 33708 — —

Back-Up Jaw 5 — — — 33655 33056

ylbmessA tfiL ciluardyH01206 .oN traP

ylbmessA mrA ffitS05206 .oN traP

POWER TONGS

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

CH-8000

The Cavins/BJ CH-8000 is designed for

fast and uniform make-up and break-out

of tubular connections on production,

workover jobs and during slimhole

drilling operations. This double motor,

chain-driven tong, has no gear transmis-

sion and clutches. The CH-8000 fea-

tures five multi-range jaw assemblies to

handle all tubing and coupling sizes

from 1-5/16" through 6-1/16" O.D. This

compact and powerful closed-head

power tubing tong, offers in this design a

combination of Cavins/BJ’s past experi-

ence with today’s technology. The exten-

sive CH-8000 field testing done to date

has shown that the elimination of gear

train, clutches and the oil lubrication

front end have drastically reduced the

amount of maintenance which is

required on other types of previously

designed power tongs. After 15 continu-

ous months of operation 12 hours per

day, 6 days per week, this tong experi-

enced no downtime.

Features:

Shift on the fly capability. Separate

speed and torque motors allow the tong

to be shifted in/out of high torque mode

easily and smoothly. No more need to

overhaul or replace transmissions. Low

maintenance and high reliability. Routine

maintenance is limited to 15 minutes per

week for lubrication. No oil bath to leak.

Jaw reversal is an easy 5 minutes. A

unique hinged top cover provides

access to the jaws so they can be

reversed for going back into the hole.

Assembly numbers:

CH-8000 Hi-speed : 250100

CH-8000 Hi-torque : 250100-1

Hydr. lift cylinder : 60210

Manual back-up : 250111

Hydr. back-up : 250111-1

SPECIFICATIONS

GT-8000

The 8000 Series tubing tong family

has been extended to include the

Gate Type Tong, which incorporates

many of the features of the CH-8000

in its small compact frame. This new

hydraulic tong is the Cavins/BJ GT-

8000.

Features:

Incorporates the same simple motor

hydraulic drive circuit as utilized in

the CH-8000. Reversible clamping

system eliminates roll-over which

occurs in other competitive tools.

Safety door prevents rotation when

door is open. The brake band is eas-

ily adjustable from outside of the

tong. Sealed bearings eliminate the

use of cam rollers and reduce main-

tenance. The hydraulic drive system

is mounted on a detachable frame for

simplified maintenance. The make-up

torque can be pre-set by adjusting a

built-in pressure relief

valve which

prevents tubular damage.

Assembly number:

GT-8000 :202100-1

Manual Back-up :200880-S

OIL WELL TOOLS

CH-8000

JAW ASSEMBLIES CH-8000

JAW AND BUSHING ASSEMBLIES GT-8000

0008-TG0008-HC

Hi Speed Hi Torque

Size range 1-5/16"-6-1/16" 1-5/16"-6-1/16" 1-5/16"-5-1/2"

33-154 mm 33-154 mm 33-154 mm 33-140 mm

Torque in Hi gear

@ 2500 psi 1100 ft-lbs 1675 ft-lbs 2150 ft-lbs

175 Bar 1492 Nm 2271 Nm 2915 Nm

Torque in Lo gear

@2500 psi 6250 ft-lbs 8500 ft-lbs 8500 ft-lbs

175 Bar 8474 Nm 11525 Nm 11525 Nm

Speed in Hi gear

@ 35 G.P.M. 132.5 L/min 140 R.P.M 103 R.P.M. 100 R.P.M.

Speed in Lo gear

@ 35 P.P.M. 132.5 L/min 32 R.P.M. 25 R.P.M. 25 R.P.M.

Size Size Jaw Assembly Back-up

8500-5565 Die

Inch mm (2) required Bushing

No. Req’d/Size

1.500" 38 201022-1 201010-1 4

1.660" 42 201023-1 201011-1 4

1.900" 48 201024-1 201012-1 4

2-1/16" 51 201025-1 201013-1 4

2-3/8" 60 8519-5055 201014-1 6

2-7/8" 73 8519-5054 201015-1 6

3-1/2" 89 8519-5053 201016-1 8

4" 102 201031-1 201009-1 8

4-1/8" 104 8519-5052 201017-1 8

4-1/2" 114 8519-5051 201018-1 10

4-3/4" 120 8519-5050 201019-1 10

5" 127 8519-5049 201020-1 10

5-1/2" 140 8519-5048 201021-1 10

Tong Jaw &

Size Size Brake ring Back-up Jaw Guide

Inch mm Assembly Assembly (5) Req’d Ring

1-5/16–1.900 33-48 250049 50-149-6-100 200395-1

1-7/8–2-3/8 48-60 200049 58-330-100 200395-2

2-3/8–2-7/8 60-73 250049 50-22-7-100 200395-2

2-7/8–3-1/2 73-89 250049 50-22-8-100 200395-2

3-1/2–4-1/2 89-114 250136 58-509-100 200395-3

4–4-3/4 102-121 250136 58-509-101 200395-3

5–6-1/16 127-154 250136 58-314 200395-4

GT-8000

HILLMAN-KELLEY®

Power Tongs

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

HILLMAN-KELLEY®Model 3700-H Standard Power Tong

Specifications

Over-all length – 42"; length from center of pipe to back-up eye – 29"

Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 560 lbs.

Hydraulic power supply required:

36 gpm @ 1000 psi

15 gpm (minimum) @ 2000 psi

Tong speeds . . . . . . . . . . . . . . . . . . . . . . . . High gear – 110 rpm

Low gear – 30 rpm

Maximum tong torque (working) . . . . . . . . . . . . . . . . . 6000 ft. lbs.

Size range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.050" – 4.5" O.D.

HILLMAN-KELLEY®Model 4600-H Deluxe Power Tong

Specifications

Over-all length – 42"; length from center of pipe to back-up eye – 29"

Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 585 lbs.

Hydraulic power supply required:

35 gpm @ 1000 psi

15 gpm (minimum) @ 2000 psi

Tong speeds . . . . . . . . . . . . . . . . . . . . . . . . High gear – 110 rpm

Low gear – 30 rpm

Maximum tong torque (working) . . . . . . . . . . . . . . . . . 6000 ft. lbs.

Size range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.050" – 4.5" O.D.

HILLMAN-KELLEY®Model 5500-H Power Tong

Specifications

Over-all length – 42"; width – 29"; length from center of pipe to

back-up eye – 29"

Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 585 lbs.

Hydraulic power supply required:

35 gpm @ 1000 psi

15 gpm (minimum) @ 2000 psi

Tong Speeds . . . . . . . . . . . . . . . . . . . . . . . . . High gear – 95 rpm

Low gear – 30 rpm

Maximum tong torque (working) . . . . . . . . . . . . . . . . . 7000 ft. lbs.

Size range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.050" – 5.5" O.D.

HILLMAN-KELLEY®Model 500 C

For Tubing and Sucker Rods

Runs single or multiple tubing strings and sucker rods Tubing

jaws for 3/4" (1.050" O.D.) through 3" (3-1/2" O.D.) tubing; Rod

jaws for 5/8" through 1-1/8".

Eliminates need to change tongs from tubing to rod…just change

the jaws.

Compact, lightweight, powerful – weights only 400 pounds.

Efficiently powers in either direction; no need to turn over to

makeup or breakout.

Quick switch from makeup to breakout accomplished in seconds.

Easy to operate from front, sides, or rear.

Uses proven planetary gear box with hydraulic motor.

Has a low gear capable of breaking any sucker rod joint.

Works smoothly with an automatic retractor.

Dual strings can be run from rig floor.

Specifications

Over-all dimensions: length – 35"; width – 16"; (12" when equipped

for multiple-string operation); height – 25"; length from center of

pipe to back-up eye – 29"

Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400 lbs.

Hydraulic power supply required:

35 gallons per minute @ 1000 psi

10 gallons per minute (minimum) @ 2000 psi

Tong Speeds . . . . . . . . . . . . . . . . . . . . . . . . . high gear – 98 rpm

low gear – 25 rpm

Maximum torque high gear. . . . . . . . . . . . . . . . . . . . . 1150 ft. lbs.

Maximum torque low gear . . . . . . . . . . . . . . . . . . . . . 4000 ft. lbs.

*To order–Specify: 1. Tong Model. 2. Part numbers. 3. Pipe O.D.

4. With or without hanger. 5. With or without Back-up.

OIL WELL TOOLS

Dies with full circle

contact for running tubing.

Jaws used when running

sucker rods.

Model 500-C Hydraulically Powered Tong

8504-5000

Model 3700-H Power Tong

8505-5000

Model 4600-H Power Tong

8509-5000

Model 5500-H Power Tong

Hillman-Kelley is a licensed trademark of

National Oilwell Varco, L.P.

8502-5344

POWER TONGS

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

OIL WELL TOOLS

Model 74-92-R Tubing

Jaw Sizes Available

1" through 3-1/2" O.D. 100 to 2,500 Ft. Lbs. Torque

Torque range high gear . . . . . . . . . . . . . . . . . . . 100 to 800 ft. lbs.

Max. torque low gear. . . . . . . . . . . . . . . . . . . . . . . . . 2,500 ft. lbs.

RPM high . . . . . . . . . . . 110* RPM low . . . . . . . . . . . . 30*

*(RPM based on published requirements of motor manufacturers

21 GPM to tong motor)

Length (A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45"

Space requirement on Pipe (B). . . . . . . . . . . . . . . . . . . . . . 6-3/8"

with Backup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-3/8"

Max. elevator Dia. (C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30"

C.L. of pipe to C.L. of Anchor (D) . . . . . . . . . . . . . . . . . . . 30-3/4"

Weight approx. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 550 lbs.

Torque reactive force at anchor pin . . . . . . . . . . . . . . . . 1,070 lbs.

Model 58-93-R Tubing & Casing

Jaw Sizes Available

1-5/16" through 7" O.D. 300 to 6,000 Ft. Lbs. Torque

Torque range high gear . . . . . . . . . . . . . . . . . 300 to 1,300 ft. lbs.

Max. torque low gear. . . . . . . . . . . . . . . . . . . . . . . . . 6,000 ft. lbs.

RPM high . . . . . . . . . . . 126* RPM low . . . . . . . . . . . . 27*

*(RPM based on published requirements of motor manufacturers

33.5 GPM to tong motor)

Length (A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51"

Space requirement on Pipe (B). . . . . . . . . . . . . . . . . . . . . . 9-1/2"

with Backup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-1/2"

Max. elevator Dia. (C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30"

C.L. of pipe to C.L. of Anchor (D) . . . . . . . . . . . . . . . . . . . . . . 30"

Weight approx. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,000 lbs.

Torque reactive force at anchor pin . . . . . . . . . . . . . . . . 2,051 lbs.

Model 54-93 Light Drill Pipe, Casing, Tubing

Jaw Sizes Available

1-5/16" through 7" O.D. 300 to 12,000 Ft. Lbs. Torque

Torque range high gear . . . . . . . . . . . . . . . . . 300 to 1,500 ft. lbs.

Max. torque low gear. . . . . . . . . . . . . . . . . . . . . . . . 12,000 ft. lbs.

RPM high . . . . . . . . . . . 130* RPM low . . . . . . . . . . . . 19*

*(RPM based on published requirements of motor manufacturers

39 GPM to tong motor)

Length (A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61"

Space requirement on Pipe (B). . . . . . . . . . . . . . . . . . . . . . 9-1/2"

with Backup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18"

Max. elevator Dia. (C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40"

C.L. of pipe to C.L. of Anchor (D) . . . . . . . . . . . . . . . . . . . 43-5/8"

Weight approx. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,360 lbs.

Torque reactive force at anchor pin . . . . . . . . . . . . . . . . 3,255 lbs.

Model 54-02 Light Drill Pipe, Casing, Tubing

Jaw Sizes Available

2-3/8" through 4-1/4" Tool Joints

2-3/8" Tubing through 10-3/4 Casing

300 to 18,000 Ft. Lbs. Torque

Torque range high gear . . . . . . . . . . . . . . . . . 300 to 1,500 ft. lbs.

Max. torque low gear. . . . . . . . . . . . . . . . . . . . . . . . 18,000 ft. lbs.

RPM high . . . . . . . . . . . . 80* RPM low . . . . . . . . . . . . 14*

*(RPM based on published requirements of motor manufacturers

55.5 GPM to tong motor)

Length (A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76"

Space requirement on Pipe (B). . . . . . . . . . . . . . . . . . . . . . 9-1/2"

with Backup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20"

Max. elevator Dia. (C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40"

C.L. of pipe to C.L. of Anchor (D) . . . . . . . . . . . . . . . . . . . 47-5/8"

Weight approx. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,600 lbs.

Torque reactive force at anchor pin . . . . . . . . . . . . . . . . 4,656 lbs.

Foster is a licensed trademark of

National Oilwell Varco, L.P.

POWER SUCKER ROD TONGS

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

MARK II THROUGH MARK VI

POWER SUCKER ROD TONGS

Description:

Purpose: Applies correct, uniform

torque, reducing costly rod failures

that often occur with hand wrench-

ing.

Special features: The possibility

of cross-threading is reduced to a

minimum. Fully throttle operated.

Torque gauge is standard equip-

ment. Easily converted for maca-

roni tubing. Choice of air or

hydraulic power.

The Cavins/BJ power rod tong

delivers ample power to make up

and break out all rod sizes. A single

unitized jaw assembly fits 5/8", 3/4"

and 7/8" (15.88 mm, 19.05 mm, and

22.23 mm) rods without change;

allows fast, unitized jaw change for

1/2" and 1", 7/8" (12.7 mm and

25.4, 22, 23 mm) rod with 1-1/8"

square and 1-1/8" (25.58 mm) rod

sizes. The rod tong is also easily

converted for macaroni tubing by

replacing the rotating jaw assembly

with macaroni tubing jaws.

Model 76 Sucker Rod Tong

Jaw Sizes Available

1/2", 5/8", 3/4", 7/8", 1", 1-1/8" Sucker Rods

100 to 2,500 Ft. Lbs. Torque

Torque range high gear. . . . . . . . . . . . . . . . . . . to 850 ft. lbs.

Max. torque low gear . . . . . . . . . . . . . . . . . . . . . 2,500 ft. lbs.

RPM high . . . . . . . . . . . 95 RPM low . . . . . . . . . . 23

Hydraulic requirement . . . . . . . . . . . . . . . 25 GPM. 2,000 PSI

Length (A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42"

Space req. on rod (B). . . . . . . . . . . . . . . . . . 10" with Backup

C.L. of Pipe to C.L. of Anchor (D) . . . . . . . . . . . . . . . . 32-1/2"

Weight approx. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400 lbs.

Torque reactive force at anchor pin . . . . . . . . . . . . . . 873 lbs.

Foster is a licensed trademark of

National Oilwell Varco, L.P.

OIL WELL TOOLS

Power Sucker Rod Tong

HOW TO SPECIFY AND ORDER

INNER RING ASSEMBLIES AND BACK-UP WRENCHES

TONG LESS INNER RING

HYDRAULIC REQUIREMENTS

000,2—000,1000,1—0mumixaMmumixaMtraPDNA SEILBMESSA

ispispdeepSeuqroTrebmuNSEHCNERWPU KCAB

Mark II (Hydraulic Motor) 27841 1,180 ft./lbs. 140 rpm 30 gpm 13 gpm

Mark IV (Hydraulic Motor) 27841-1 1,370 ft./lbs. 120 rpm 30 gpm 13 gpm

Mark V (Hydraulic Motor) 27841-5 1,850 ft./lbs. 90 rpm 30 gpm 13 gpm

AIR PRESSURE REQUIREMENT

mumixaM isp 021mpr 021.sbl/.tf 081,193372)rotoM riA( III kraM

mumixaM isp 021mpr 98.sbl/.tf 058,16-

14872)rotoM riA( IV kraM

Size of Rod 1/2" 5/8" 3/4", 7/8" 1" 1-1/8" 7/8" Rod with 1-1/8" Square

Rod Inner Ring 27899-2 27899 27899-4 27899-1 27899-3

Rod Back-Up Wrench 27898 27902 27903 27906 27907 27903-1

Size of Macaroni Tubing 1.050" 1.315" 1.660" 1.900" . . . . . . . .

Finger Saver 27894-10 Safety Tool 27899-W

ubing Inner Ring 30718 30716 30714 30712 . . . . . . . .

MANUAL TONGS

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

KELCO®FULGRIP®Tubing Tongs

The “wrap-around” design gives a 360° grip on the tubing

with 88% to 95% of the circumference area in die contact. As

a result there is little possibility the pipe will be scored or

crushed during making or breaking the string.

FULGRIP Tongs are lightweight, easy to transport and use.

Their sturdy design and tough construction tend to deliver

dependable, long-lasting service.

These tubing tongs are available in four types:

Type A-20 – lightweight, aluminum tong for macaroni tubing

1.050"-2.063" O.D. and plastic tubing 1.050"-2.500" O.D.

Type K-20 – high grade steel tongs for rugged, dependable

field service for tubing 1.050"-2.500" O.D., 1,500 Ft.-Lb.

torque rating.

Type K-25 – high grade steel tongs for tubing 1.200"-3.063"

O.D., 2,000 Ft.-Lb. torque rating.

Type K-30 – for heavy-duty service for tubing 2.062"-4.125"

O.D., 5,000 Ft.-Lb. torque rating. This tong is available with

either standard hanger (K-30A) or with rollover block (K-

30B).

SNAP-ON TUBING TONG

Purpose: Strong, quick-acting tubing tong made of high-qual-

ity, heat-treated steel.

Description: This easily handled tong is “snapped on” with

one hand, locking automatically around the tubing. It can be

released only by the operator. The tong is held open when off

the tubing, or in a closed position around the pipe, by two

spring plungers which act directly against the body and lever.

The BJ tong die is held at the proper angle for taking an

instant, positive grip, releasing readily when the operator

ratchets the tong. This firm, non-slip grip permits unscrewing

joints of tubing up to 3-1/2" diameter without crimping.

DESCRIPTION OF SNAP-ON TONG MODELS

Order by Tong Description and Part Number

DESCRIPTION OF SNAP-ON JAW ASSEMBLIES

FIG. 1 – Type A-20 Tubing Tong

TABLE NO. 1

FIG. 2 – Tong Pull-Back Strap

TABLE NO. 1

Tong Pull-Back Strap

TYPE

“MS” TONG

Purpose: Light drilling and

tubing work, including seis-

mograph, shot-hole and

exploration drilling.

Description: The Type MS

has proved its efficiency in

the field on all types of slim-

hole drilling rigs. It has a T-

head latch which, with the

2-step and 3-step lug jaw

construction enables the

tong to fit both pipe cou-

pling and tool joint without any adjustment. The 3-jaw design

permits uniform contact around the circumference of the pipe.

The tong is strong enough to easily break both tool joints and

bits in light drilling operations.

A rigid hanger suspension device allows fast, permanent

adjustment, holding the tong balanced and ready for use. The

Type MS is equipped with the same roll-over hanger feature

found on the Type WS. All parts are interchangeable except

the long jaw, latch, and lug jaws. The changes are slight

dimensionally, but greater performance can be expected.

Size Range: 1.900" through 6-1/8" O.D.

Torque Ratings: 6

,500 ft. lbs. from 1.900" through 6-1/8" O.D.

TO ORDER TONG COMPLETE

30425-110 “MS” Tong Complete with 2-3/8"–3.668" Lug Jaw Assembly

SPECIFICATIONS

Order by Part Number, Part Name and Size

OIL WELL TOOLS

T rebmuN traPledoM gno

Snap-On Tong Complete, with Back-up for 2-3/8" O.D.

732-61863gnibuT IPA

Snap-On Tong Complete, with Back-up for 1.90" API

052-61863gnilpuoC gnibuT tespU

Snap-On Tong Complete, with Back-up for 2-7/8" O.D. API

Tubing and 2-3/8" API Plain Tubing Coupling 36816-287

Snap-On Tong Complete, with Back-up for 2-3/8" O.D. API

603-61863gnilpuoC gnibuT tespU

Snap-On Tong Complete, with Back-up for 3-1/2" O.D. API

Tubing and 2-7/8" API Plain Tubing Coupling 36816-350

Snap-On Tong Complete, with Back-up for 2-7/8" API

663-61863gnilpuoC gnibuT tespU

T )seiD sseL( rebmuN traPegnaR eziSepy

A-20 1.050” – 2.063” (26.7mm – 52.4mm) 8527-5002

K-25 1.200” – 3.063” (30.5mm – 77.8mm) 8527-5016

K-30 2.062” – 4.125” (52.4mm – 104.8mm) 8527-5035

K-30A 2.062” – 4.125” (52.4mm – 104.8mm) 8527-5036

K-30B 2.062” – 4.125” (52.4mm – 104.8mm) 8527-5037

Item No. Req’d. Part Number Wt., Lbs. Each

Pull-Back Strap 1 24747 3

rebmuN traPylbmessA

2-7/8" API Upset Coupling Jaw Assembly 37046-3

2-44073ylbmessA waJ gnibuT IPA "8/3-2

2-7/8" API Tubing and 2-3/8" API Plain Coupling Jaw Assembly 37042-2

3-1/2" API Tubing and 2-7/8" API Plain Coupling Jaw Assembly 37046-2

3-44073ylbmessA waJ gnilpuoC tespU IPA "09.1

2-3/8" API Upset Coupling Jaw Assembly 37042-3

.tWtraP

.zO—.sbLrebmuN traP.d’qeR

30425 “MS” TONG COMPLETE LESS LUG JAWS (1.900"–4-1/2") 43

31131 “MS” TONG COMPLETE LESS LUG JAWS (4-1/2"–6-1/8") 44

Kelco, Fulgrip and Snap-on are licensed trademarks of

National Oilwell Varco, L.P.

SUCKER ROD & TUBING

ELEVATORS

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

TYPE ‘TA’ CENTER LATCH ELEVATORS

Purpose: Center-latch elevators of superior design

for handling collar-type drill pipe, casing and tubing.

Description: All TA elevators are constructed in two

halves of practically the same weight, providing

proper balance and easier opening and closing.

Special Features: Proper balance for easier han-

dling; latch and safety latch lock combinations; other

operator safety features

Safety features include guarded operating han-

dles to help prevent accidents to operators and an

extra handle at the rear of the elevators for easier,

safer operation. All TA elevators are equipped with a

latch and safety latch lock combination.

‘D’ SERIES

SIDE DOOR ELEVATORS

NO-KINK ROD ELEVATORS

PURPOSE: Safe efficient han-

dling of sucker rod sizes from 5/8"

(15.88 mm) through 1-1/8" (28.58

mm). Can also handle hollow type

sucker rod and tubing.

Special Features: Will not bend

or kink sucker rods even under the

heaviest loads.

Reversible-type body.

Capacity: The No-Kink elevator is

available in a heavy type, 43,000-

pound (19504.8 kg) capacity, for

longer rod strings.

NOTE: When ordering No-Kink

rod elevator for use with hollow-

type sucker rods or for handling

tubing, please specify make and

size of rod or tubing.

OIL WELL TOOLS

TA Elevator

“TA” SERIES COLLAR TYPE CENTER LATCH ELEVATORS A SERIES

*Must specify O.D. size and type of tubulars (plain or upset)

D SERIES SIDE DOOR COLLAR TYPE ELEVATORS

PURPOSE: Side-door elevators for handling plain or upset Collar-type

drill pipe, casing and tubing. Available in Type LD and LLD model.

Size Ranges and Capacities: API pipe sizes from 2-3/8" (60.33 mm)

through 3-1/2" (88.9 mm) O.D. See the table below.

For Collar-Type Drill Pipe and Tubing – Order by Part Number, Part Name and Size

SPECIFICATIONS–TYPE “LLD” SIDE DOOR ELEVATOR

*Must specify O.D. size and type of tubing (plain or upset)

SPECIFICATIONS–TYPE “LD” SIDE DOOR ELEVATOR

*Must specify O.D. size and type of tubing (plain or upset)

NO–KINK ROD ELEVATOR–HEAVY TYPE

REPLACEMENT PARTS–HEAVY TYPE

thgieW.paC.RN emarFepyTeziS

gkzo-blsnoTmmsehcnI

1.050—2-7/8 27—73 TA 32387–* 35 39 18

1.660—2-7/8 42—73 TA 32385–* 65 65 29

3-1/2—4-1/2 80—114 TA 32386–* 65 83 38

2-3/8—2-7/8 60—73 TA 32383–* 100 100 45

3-1/2—5 89—127 TA 32384–* 100 158 72

detaR.xaM dna .niM

Body Dia. Weldless Weight Cap.

No. Links Lbs.—Oz. Tons

2-3/8" 12591—* 1-3/4"—2-1/4" 138—0 100

2-7/8" 12591—* 1-3/4"—2-1/4" 136—0 100

3-1/2" 12591—* 1-3/4"—2-1/4" 133—0 100

hctaL tnorFetelpmoC rotavelE

Rod Part Wt. API Rated No. Part Wt.

Size No. Lbs–Oz. Cap.—Labs. Req. No. Lbs.—Oz.

5/8", 3/4" 27725 28—0 43,000 2 11745 0—8

3/4", 7/8" 27726 28—0 43,000 2 11746 0—8

1" 27727 28—0 43,000 2 11746-1 0—8

1-1/8" 27727-1 28—0 43,000 2 11746-2 0—8

.tWtraP.oN

.zO—.sbLemaN traP.oN.qeR

18–01liaB25772

26—0hctaL raeR93621

43—0niP hctaL22772

22—0gnirpS hctaL3606

2 28147 Bail Retainer Washer 0—3

Elevator Complete

Min. and Max. Dia. Rated

API Size Frame Weldless Links Capacitiy Weight Ea.

In. mm No.l in. mm tons tonne lb kg

2-3/8 60.33 23296—* 1-3/4—2-1/4 44.45—57.15 65 58.97 83 37.65

2-78 73.03 23296—* 1-3/4—2-1/4 44.45—57.15 65 58.97 82 37.20

31/2 88.9 23296—* 1-3/4—2-1/4 44.45—57.15 65 58.97 80 36.29

ROD & CRANE HOOKS

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

Purpose: Sucker rod handling equipment for every depth and

operating condition.

Description: Cavins/BJ

rod hooks are offered in two sizes–20

and 35 ton capacities–engineered to Cavins/BJ’s exacting stan-

dards of quality. High-strength steel property machined, heat-

treated and tested, ensures long, trouble-free service.

The locking mechanism on both models is operated by

means of a one-hand grip at the hook’s center of balance. This

allows the operator to steady the hook, open the locking arm

and engage or remove the bail in one smooth, continuous oper-

ation. A strong loop guard protects the operator’s hand.

The Cavins/BJ Model R-35 has a relief spring that provides

2–2-1/2" of travel. It has ample strength to lift a stand of rods,

reducing the possibility of damage to pin and coupling threads.

The Model R-35 Hook also has a large bail as standard equip-

ment.

Sizes and Capacities: The Model R-20 has a rated capacity of

20 tons and the Model R-35 has a rated capacity 35 tons in

accordance with API standards.

REPLACEMENT PARTS–Cavins/BJ ROD HOOKS

Purpose: Cavins/BJ

crane hooks are offered in two sizes: 10

and 25-ton capacities engineered to Cavins/BJ exacting stan-

dards of quality. High-strength steel, properly machined, heat

treated and tested, insures long, trouble-free service.

The locking mechanism on both models is operated by

means of a one-hand grip, protected by a strong loop guard.

The crane hook body can be adapted to most all crane blocks

on special request.

Sizes and Capacities: The Model C-10 has a rated capacity of

10 tons and the Model C-25 has a rating of 25 tons in accor-

dance with API standards.

CRANE HOOKS–REPLACEMENT PARTS

OIL WELL TOOLS

R-35 Rod Hook

R-20 Rod Hook

C-10 & C-25

Crane Hooks

R-35 Rod Hook

R-20 Rod Hook

DIMENSIONAL DATA

C-10 & C-25

Crane Hooks

02-R ledoM53-R ledoM

thgieWthgieW.oN.feR

No. Req. Part Name Part No. Lbs.—Oz. Part No. Lbs.—Oz.

… … R-20 Hook Complete ……… ……… 32040 49—0

… … R-35 Hook Complete 31982 84—0 ……… ……

1 1 Body 31965 41—0 32039 20—0

2 1 Bail Housing 31966 27—0 32041 20—0

3 1 Grease Fitting 940308-1 0—1 940308-1 0—1

4 1 Shank Spring 31968 5—0 ……… ……

5 1 Thrust Bearing Assembly 942440-1 4—0 942441-21 3—0

6 1 Hex Nut 32626 1—0 32626 1—0

71 2—082-9217492—082-921749niP

8 1 Bail Housing Cap 31967 2—0 8222 1—12

9 2 Screw 900042-12 0—2 ……… ……

10 1 Latch Handle 31971 1—8 31971 1—8

11 1 Latch Spring 31973 0—4 31973 0—4

12 1 Latch 31972 1—0 31972 1—0

2—0236232—023623niP231

14 2 Cotter Pin ……… ……… 939672-55 0—2

15 1 “O” Ring ……… ……… 942271-43 0—1

No. Model Model

Part Req’d. C-25 C-10

Hook Complete 1 32842 32848

Body 1 32837 32847

Bail 1 32041 32041

Cap 1 8222 8222

Spring 1 31973 31973

Nut 1 32626 32626

O-Ring 1 942271-43 942271-43

Bearing 1 942441-21 942441-21

Cotter Pin 1 939672-73 939672-73

Latch Handle 1 31971 31971

Latch 1 32836 32836

Pin 2 32632 32632

Cotter Pin 2 939672-55 939672-55

Grease Fitting 1 940308-1 940308-1

Size R-35 R-20

Type Spring Plain

Spring

Travel 2-1/2 None

A 37-5/16 25-1/4

B 7-7/8 6-3/4

C 7-3/8 6-3/8

D 1-7/8 1-7/8

E 11-1/4 4-1/2

F 4-5/8 4

G 1-13/16 1-13/16

H 1-1/2 1-3/8

J 2-1/2 2-3/8

K 31-11/16 20-1/4

L 1-7/8 1-1/2

R 2 1-1/2

Model Model

Reference

C-25 C-10

A 6-3/8" 6-3/8"

B4" 4"

C 1-3/8" 1-3/8"

D 2-3/8" 2-3/8"

E7" 7"

F 29-9/16" 27-13/16"

G 23-9/16" 22-7/16"

H 1-1/2" 1-1/2"

I 2-1/2" 2-1/2"

J 4-1/4" 4-1/4"

K 3-1/4" 3"

L 2-1/2" 2-1/4"

M 10-3/4" 9-1/2"

F G

ELEVATOR LINKS & HOOKS

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

TOOLPUSHER LINKS

Description: Toolpusher Links are forged from a single piece of high grade alloy steel

to provide maximum tensile strength. More weight and “plus-diameter” in critical areas

make these Cavins/BJ links extra strong. Short upper eye design means better balance

and easier elevator handling, while reducing wear of the eye section against the swivel

bail or body.

SPECIFICATIONS – TOOLPUSHER LINKS

*Sold only in sets

WEB WILSON®

HYDRA HOOK™

The Web Wilson Hydra Hooks are available in four differ-

ent capacity ratings from a 40 ton to the 150 ton model.

There are a number of features in each Hydra Hook

designed to add convenience and long life to your rig.

Some of these are:

Hydraulic cushion controls bounce to reduce thread

damage when “jumping out” pipe

Heavy-duty main spring provides extra force to “jump

out” heavy pipe stands

Main roller-type bearing with large contact area always

submerged in oil

Continuous lubrication of main spring and shank

Split ring assembly connects shank to hook

Choice of connections – clevis-to-bail, direct, or unitized

Oil changes easily made with hook hanging from blocks

Web Wilson and Hydra-Hook are licensed trademarks of

National Oilwell Varco, L.P.

Fig. 1

150-Ton HYDRA HOOK

Fig. 2

Major Parts of HYDRA HOOK

OIL WELL TOOLS

Rated

Capacity/Set Weight/Set

Part No.* Size–in. Size–mm Tons lb kg

37355-1036 1-3/4 x 36 44.45 x 914.4 150 125 56.7

37355-1048 1-3/4 x 48 44.45 x 1219.2 150 160 72.6

37355-1060 1-3/4 x 60 44.45 x 1524.0 150 190 86.2

37355-1072 1-3/4 x 72 44.45 x 1828.8 150 230 104.3

37355-1084 1-3/4 x 84 44.45 x 2133.6 150 270 122.5

37355-1096 1-3/4 x 96 44.45 x 2438.4 150 310 140.6

37355-1120 1-3/4 x 120 44.45 x 3048.0 150 390 177.3

150 Ton For depth from 5,500 to 8,000 feet using 4-1/2"

drill pipe or 7,000 to 10,000 using 3-1/2" drill pipe.

100 Ton For depths from 4,500 to 7,000 feet using 3-1/2"

drill pipe.

65 Ton For depths from 2,750 to 4,500 feet using 3-1/2"

drill pipe and tubing handling.

40 Ton For handling of tubing and for drilling to 2,750

feet using 3-1/2" drill pipe.

SHANK

HEAD COVER

SPLIT RING

SPRING PILOT

SPRING

PILOT GASKET

“O” RINGS

DUST SEAL

SET SCREW

BEARING

DRAIN PLUG

ASSEMBLY BOLT

(14 THREADS

PER INCH)

USE ONLY FOR

ASSEMBLY OR

DISASSEMBLY

SWIVEL LOCK RING

DUST SEAL

COVER

SHANK HEAD

MAIN SPRING

BODY

SHANK

EQUALIZER RING

CAVINS ROD TYPE SAND PUMP

For General Production Clean Out Service

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

This very rugged and efficient Sand Pump is used for general utility production clean out

work where it is not necessary to flush the perforations by means of hydraulic surge. It will

function very efficiently in wells having little fluid and also where fluid in the wells is of a

heavy viscous nature down to 9° A.P.I. gravity. A special blow-out feature is incorporated

which utilizes any gases entrained in the well fluid to discharge the load. A Quick Change

Rope Socket, Sinker Bar, Bottom Sleeve, regular flat adjustable Shoe, Dump Key, and

Wood Clamp (Fig. 1) are furnished as standard equipment with all Sand Pumps 1-3/4" O.D.

and larger.* Load Tubes, Bridge Buster Shoes (Fig. 3), Chisel Shoes (Fig. 4), Rein Jars or

Tubular Jars can be supplied along with many other accessories.

*O.D. of wire line must be specified when ordering.

OIL WELL TOOLS

Spring Type Dump Key

Assembly consists of

spring and spring

housing. Is used to

adapt the Dump Key

Wedge for Flat and

Bridge Buster Shoes

and the Round Nose

Shoe Dump Key.

Fig. 1

The Wood Clamp

Assembly slips over

the end of the Working

Barrel or Load Tube.

Its function is to clamp

around the tube and to

suspend the pump

while making up sec-

tions of the tool.

The Bridge Buster

Shoe is used to break

up hard packed sand

and bridges. It is

made from alloy

steel, heat treated

and hard faced on the

cutting edge.

Fig. 3

The Chisel Shoe is

used to break up hard

pieces of cement,

lime, shale, or rocks

that are too large to

enter the bottom of

the tool. It is made

from alloy steel, heat

treated and hard

faced on the cutting

edge.

Fig. 4

The Metal Plunger is

recommended for

wells with elevated

temperatures, replac-

ing the regular

Plunger assembly.

Suction is attributed

to cascade seals. Is

also effective for use

in wells operating

under normal temper-

ature conditions.

Fig. 5

Fig. 4

The Multi-Lip Plunger (Fig. 2) is available

as a standard feature for most sizes of

Cavins Sand Pumps. It is made of synthetic

oil-resisting rubber and is recommended for

normal bailing operations where the well

temperature does not exceed 200°F. A strong

bond between the high strength rubber and

the steel mandrel on which it is mounted pre-

vents the stripping of rubber, even under

severe operating conditions. The multiple lips

provide a perfect upstroke seal and automat-

ically compensates for wear. In wells where

elevated temperatures are encountered,

such as in secondary recovery operations,

an all metal plunger (Fig. 5) is recommended.

The Plunger is designed with a labyrinth seal

which does not require any packing.

However, “O”-Rings may be used for addi-

tional sealing if desired.

ENGINEERING DATA

*These lengths are for single section Sand Pumps.

Optionally, we manufacture 40', 50', and 55' Double

Section Sand Pumps for which a load tube section

must be ordered as an accessory.

For Use In Wgt. Lgth*

Sand Pump Size Pipe I.D. Lbs.

(Feet)

1-1/4" O.D. (Cavins Model 5A) 1-1/2" – 2-1/2" 75 30

1-1/2" O.D. (Cavins Model 4A) 2" – 3" 140 30

1-3/4" O.D. (Cavins Model 3A) 2" – 3" 165 35

2-1/8" O.D. (Cavins Model 2A) 2-1/2" – 4" 265 35

2-5/8" O.D. (Cavins Model A) 3-1/2" – 5" 320 35

3-1/8" O.D. (Cavins Model B) 5" – 8" 400 35

3-3/4" O.D. (Cavins Model C) 6" – Up 500 35

4-1/2" O.D. (Cavins Model E) 6" – Up 630 35

New Style

Old Style

CAVINS HYDROSTATIC BAILER

Telescoping Valve Section Type

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

(Fig. 1) (Fig. 2) (Fig. 3)

JUNK BASKETS (Fig. 1)

Cavins Junk Baskets are used with

the Cavins Automatic Hydraulic Suction

Bailer and Fishing Tool for fishing out

movable objects that are too large to

enter the regular bailer bottom. Such

Junk Baskets are extremely successful

in recovering rock bit cones and cutters,

blades from drag bits, pipe slivers, drilled

up cement retainers and bridging

plugs,

tubing collars, packer rubbers, etc.

SKEETER BILL (Fig. 2)

Used with the Cavins Automatic

Hydraulic Suction Bailer for cleaning out

around and inside of stuck fish, such as

gas anchors, tubing, etc., preparatory to

fishing with a socket or spear; also to

clean out around other fish which cannot

be recovered, but which may be chased

to bottom in this manner.

It consists of a sub for attaching to

bailer bottom, and a small O.D. thick-

walled, seamless tubular extension up to

20 feet long. Available in both straight

and off-set types. In the latter type, the

off-set is not carried beyond the bailer

O.D. (not shown) unless so specified.

When ordering, specify type desired,

length of extension, and size of bailer on

which it is to be run.

BY-PASS VALVE (Fig. 3)

This device is subbed between the

bailer bottom and the Junk Basket. It per-

mits the well fluid to by-pass up through

the Junk Basket, thus permitting the bail-

er assembly to descend to bottom freely

and without interruption. For use espe-

cially with larger size of Junk Baskets

where the clearance between the O.D. of

the basket and the I.D. of the well bore,

or casing, is restricted.

Run on wire line on any type of

hoisting rig.

This outstanding Bailer utilizes the

fluid column (500 ft. min.) standing in the

well to create the hydraulic energy

required for its operation. It is the most

efficient tool for breaking hard packed

sandbridges in Casing and Tubing, fish-

ing out all types of movable junk, clean-

ing out through collapsed pipe, etc. The

CAVINS Junk Basket can be attached to

the bottom of the Bailer for fishing out

movable objects too large to enter the

Regular Bailer Bottom. The Junk Baskets

are extremely successful in recovering

Rock Bit Cones, Cutter Blades from Drag

Bits, Pipe Slivers, drilled up Cement

Retainers, Bridging Plugs, Tubing

Couplings, Packer Rubbers, etc. It will

efficiently flush the perforations.

The CAVINS Hydrostatic Suction

Bailer consists of a Jar Section, a

Suction Chamber, a Telescoping Valve

Section and a Load Chamber. It can be

run on any size wire line and with any

type of hoisting rig. The creation of a

Pressure Differential is accomplished by

the submergence of the Bailer with the

Suction Chamber filling with air at atmos-

pheric pressure. When the tool comes to

rest at the bottom, the weight of the

Suction Chamber Tube and the Jar

Section, which are all located above the

Telescoping Valve Section, opens the

Valve Section and exposes the Atmos-

pheric Pressure in the Suction Chamber

to the greater pressure in the Fluid

Column. This fluid rushes into the empty

Suction Chamber Tube with sufficient

velocity to carry everything with it

which is at or near the Bailer Bottom.

The CAVINS Multi-Surge

Junk Snatcher is a hydrostatic

multi-action junk fishing tool

which runs on drill pipe or tub-

ing and works on the same

principle as the Hydrostatic

Bailer.

Cavins “Wood Clamp” assem

blies are supplied with each

Hydrostatic Bailer, as well as

Sand Pumps, to hold the tool

above the well head while it is

being made up or taken apart.

The “Dump Key” is in a spring

loaded housing which can be

securely spiked to the floor to

turn the bottom sleeve assem-

bly to enable the bailer or sand

pump to be emptied of its load.

OIL WELL TOOLS

QUICK CHANGE

ROPE SOCKET

VALVE SECTION

ASSEMBLY

Top Connection

Sinker Bar

REIN JAR

ASSEMBLY

LOAD TUBE

ASSEMBLY

SUCTION

CHAMBER

ASSEMBLY

BOTTOM SLEEVE

ASSEMBLY

Lower Sub

Liner Guide

Valve Cap for

Air Leak Test

Relief Valve

Relief Valve Spring

Screw Wrench

Wood Clamp

Assembly

Shoe Complete

With

Adjustable Sleeve

Bottom Dumping Key

(Fig. 4)

SPUD GUIDE DRAG MILLING

Fig. 2 Fig. 3 Fig. 4 Fig. 5

“MULTI-SURGE” JUNK SNATCHER

For Recovery of Small Junk in the Well

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

The Junk Snatcher operates on a pressure-differential principle which permits

repeated high velocity hole-cleaning surges in one run of the pipe. This unique

and efficient multi-Surge Action is obtained without the use of fluid pumps at the sur-

face and with a minimum of manipulation of the fishing string. Complete Junk Basket

Assemblies to accommodate virtually any size hole and fish are available with the

MULTI-SURGE Junk Snatcher. Each lower Junk Basket assembly is threaded to

accommodate the use of the Guide Shoe, or other attachments; to break, shape, or

center junk prior to each surging operation. Each complete surge of the Junk

Snatcher is instantaneous and the operator need only to pick up the fishing string to

ready the tool for repeated operations.

INSTALLATION OF THE CAVINS JUNK SNATCHER

PARTS IN THE DRILL STRING

OIL WELL TOOLS

Fig. 1

BOTTOM

SHOES

BOX BOX

SUB

(KELLY)

BOX

TOP

DRILL

PIPE

DRILL

PIPE

MAIN

CONTROL

VALVE

FLOAT

VALVE

FLUID

BY-PASS

VALVE

UPPER

JUNK

BASKET

LOWER

JUNK

BASKET

Fig. 6

CLOSED

Fig. 7

OPEN

BOX

SUB

PIN PIN

BOX

SUB

BOX

UPPER

JUNK

BASKET

BY-PASS

VALVE

FLOAT

VALVE

MAIN

VALVE

LARGE

JUNK

BASKET

TYPE OF

SHOE

BOTTOM

DRILL PIPE

HYDROSTATIC TUBING BAILER

For General Bailing Service

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

For more than half a century CAVINS has been the leader in the manufacturing of pro-

duction bailing equipment for sand. One of the pioneers of proven bailing tools is the CAVINS

Telescoping Hydrostatic Valve Section Bailer for use on wire line. The CAVINS Hydrostatic

Tubing Bailer works on the same principle as the wire line type bailer only it is run on the

tubing string thereby greatly increasing the volume of sand which can be removed with each

run.

The Hydrostatic Tubing Bailer operates on a pressure differential basis utilizing the fluid

column (1000 ft. min.) standing in the well to create the hydraulic energy required for its func-

tion. As the tubing string is lowered and contacts the fill the valve section is opened drawing

sand into the string which is trapped by a check valve. This type of operation can continue

until the differential pressure has been equalized. The tubing is then pulled from the well and

cleaned out. If desired the By-Pass Valve Section can be run which allows the string to be

pulled dry above the load of sand.

The Tubing Bailer is one of the most efficient means of sand recovery where high volume

of fill exists in the well. This method is far superior to simple circulating techniques not only

because of the obvious savings of costly time and equipment but also because the sand is

drawn with hydraulic suction rather than high pressure with a circulating pump which actu-

ally can force the sand back into the perforations of the well liner. The hydraulic surge from

the Tubing Bailer will effectively flush the perforations during sand recovery operations.

OIL WELL TOOLS

Fig. 2

Fig. 1

Tubing Bailer

Valve Section

TUBING TUBING

BOTTOM

SECTION

WITH

CHECK VALVE

AND SHOE

BY-PASS

VALVE

KNOCK OUT

COLLAR

TUBING

TUBING BAILER

VALVE SECTION

OPTIONAL

SAW TOOTH

SHOE

By-Pass

Valve

Section

Bottom Valve Section

With Check Valve and

Bridge Buster Shoe

Optional

Drag Shoe

CAVINS “TURBO” BAILER

For Use With Tubing

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

The CAVINS “TURBO BAILER” is engineered for fast, efficient well cleanout especially

when large amounts of fill or scale are encountered. It has proven to be a very cost effective

tool over conventional sand line bailers in these situations and unlike the Hydrostatic Tubing

Bailer, the “TURBO BAILER” can be run in shallow or any depth well with a relatively low

fluid level.

The “TURBO BAILER” working barrel chamber is run in the tubing string, utilizing a flap-

per valve placed strategically to insure positive containment of debris inside the tubing.

HOW IT WORKS

The “TURBO BAILER,” in the tubing string, is set into the existing fluid level of the well at

which point the tool is stroked in a manner similar to a sand pump. The up-stroke evacuates

debris from the well upward through the shoe into the tubing and as a result is trapped above

the flapper valve which closes during the down-stroke motion. As fluid reaches the plunger

assembly, it passes through a check valve and is discharged through return ports back into

the well. This stroking is repeated until the tubing is filled with sand and/or debris.

The “TURBO BAILER” offers certain advantages over sand line bailers. The lift rod is of

heavy duty hex design which affords the tool to be rotated with the tubing string to facilitate

getting through sand bridges or breaking up hard packed fill.

The “TURBO BAILER” has additional benefits over conventional circulating techniques

including cost reduction through elimination of expensive pumping equipment and special

circulation fluids (minimizing environmental impact) as well as avoiding the use of high pres-

sure in the well which can force sand back through the perforations and into the formation.

In contrast, the “TURBO BAILER” actually cleans the perforations during operation with its

suction action.

The CAVINS “TURBO BAILER” may be run on all sizes of tubing and drill pipe.

SIZES

OIL WELL TOOLS

Model O.D. Threads

B 3-1/8" 2-3/8" EUE-8rd

C 3-5/8" 2-7/8" EUE-8rd

E 4-1/2" 3-1/2" EUE-8rd

Fig. 2

TURBO

BAILER

BUTTOM

SUB

SAW-TOOTH

SHOE

BOTTOM

FLAPPER

ASSEMBLY

TURBO BAILER

TO TOP OF

WELL

PORT

HOLES

TUBING

STRING

ABOVE

TURBO

BAILER

DRAIN

HOLE

PERFORATED

NIPPLE

WORKING

BARREL

HEX LIFT

ROD 10 1/2’ STROKE

TUBING

BELOW

TURBO

BAILER

(LENGTH

DETERMINED

BY WELL

CONDITIONS)

SAW-TOOTH

SHOE

SAND

DEBRIS, ETC.

BRIDGE

BUSTER

SHOE

FLAPPER VALVE

Fig. 1

CAVINS DEPTHOMETER

For Wire Line Well Measuring

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

DEPTHOMETER WITH FLOORSTAND

The Cavins Depthometer has no equal for quick, accurate wire

line measurements of oil, gas and water wells, particularly when

perforating, bailing, cleaning out, swabbing, single shot, or similar

operations. It has proven valuable in both on-shore and off-shore

operations. This tool is also used for measuring armored cable for

submersible pumps. The Cavins Depthometer has made “string-

ing-in” obsolete, and is being adopted as standard equipment for

production and well drilling operations. The Cavins Depthometer is

available for 7/16" – 5/8" O.D. wire lines and 3/4" – 1" O.D.

The range for which the Depthometer is to be used must be

specified on the order. If the tool is to be used for both ranges, an

extra main measuring wheel can be supplied, which can be

exchanged in the field in a few minutes time. Cavins Depthometers

are available for recording measurements in feet or meters. They

can be supplied with all bronze bearing construction Model “BL” or

all ball-bearing construction Model “CL”.

When ordering, please state the following information:

Range of Wire Line size

Measuring in feet or meters

Model “BL” All Bronze Bearing type

Model “CL” All Ball Bearing type with or without

carrying case and stand or with Carrying Case

and Hanger

Each Cavins Depthometer bears a Model Number and Serial

Number. The range of size lines for which it is to be used is

stamped on one spoke of the main wheel. When ordering spare

parts please mention the Model, Serial Number and Wire Line

size.

Shipping Weights and Measurements

Net Weight 36 Lbs. 16.3 Kg.

Tare Weight 24 Lbs. 10.9 Kg.

Gross Weight 60 Lbs 27.2 Kg.

Export Shipping Case: 14" x 17" x 21" = 2.9 Cu. ft. –

36 x 43 x 53 Cm. = .08 Cu. Meters.

Depthometers for special wire line size are available on application.

Maximum Reading 999,999 Feet or 999,999 Meters.

Net Weight of Depthometer Only11 Lbs 5.0 Kg.

Fig. 1

DEPTHOMETER EYE BOLT HANGER

To facilitate the safe handling of the Cavins

Depthometer on rigs where it is impractical or

impossible to securely anchor to the usual

Floor Stand, an Eye Bolt Hanger can be sup-

plied. It can be supported from a sand line or

cat line from the rig top. The hanger engages

the Depthometer in exactly the same manner

in which the floor stand is attached and sim-

plifies the removal of the tool.

Fig. 3

DEPTHOMETER

CARRYING CASE

The Cavins Depthometer

and Stand or Eye Bolt

Hanger can be supplied with

a heavy duty, light weight

carrying case. It protects the

instrument and especially

the counter from the ele-

ments and provides a com-

pact storage place for com-

plete assembly.

OIL WELL TOOLS

Fig. 2

M450

M430

M460-L

ELECTRONIC DEPTHOMETER

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

CAVINS is pleased to announce the introduction of a

Depthometer equipped with Electronic displays for use on Coil

Tubing units. The displays are mounted in a NEMA 4 rated

enclosure and optionally can be mounted on a face plate to fit

in your control console. The unit comes standard with the fol-

lowing features:

The unit displays both Depth and Rate of Tubing travel.

By simply adjusting the calibration, display can be either in

feet or meters.

As the main wheel wears, accuracy can be maintained by

field calibration.

A direction switch allows the counter to increment from zero

regardless of the manner in which the depthometer is

mounted.

The counter allows an alarm to sound for up to 99.99 sec-

onds when a preset depth is reached.

The rate display can be programmed to sound an alarm

when the rate of tubing travel falls outside of a preset range.

A conversion kit is available to convert an existing mechan-

ical depthometer into an Electronic display type.

Counter/Rate display features:

English Prompts

Easy to Read

Easy to program

Large LED Display

5 Digits

High Intensity

High Contrast

Sealed Front Panel

NEMA 4 rated

Oil Tight

WaterTight

Chemical Resistant

Power Input

110 VAC or 10-26 VDC

EXTRA LARGE COUNTERS

FOR CAVINS DEPTHOMETERS

An optional Extra Large Counter is available when ordering

a new Depthometer or as a conversion kit for your own Cavins

Depthometer.

The Extra Large Counter has full 3/4" high numerals which

are more than twice the size used on the standard

Depthometer counter and facilitate easier reading in applica-

tions where the unit is mounted a short distance away from the

operator such as on coiled tubing rigs.

The following configurations (Fig. 3) are available for the

Extra Large Counter. Our standard configuration is #3, howev-

er, the configuration for your use may vary according to your

particular application and mounting location of the

Depthometer on your rig.

To order a complete Depthometer with the Extra Large

Counter or a conversion kit please specify the same informa-

tion as for a standard Depthometer and add the wording; with

Extra Large Counter with 3/4" numerals and also specify the

desired configuration (1, 2, 3 or 4).

OIL WELL TOOLS

Fig. 2

Extra Large Counter

Fig. 3

Counter Rotations

12 3 4

BALL LOCK OIL SAVER

For: Blow-Out Prevention and Line Wiping

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

BALL LOCK OIL SAVERS

The use of the Ball Lock Oil Savers by drilling and production departments

has earned this service proven tool a reputation for trouble-free operation with

simplicity. The CAVINS Ball Lock Oil Savers (Fig. 1) are made of high carbon

steel and precision machined for demanding dependability and safety in a wide

range of service applications. Exhaustive testing in the excess of 3000 psi is fur-

ther assurance against failure or leakage. Incorporated in its design, which

affords a cleanly wiped wire line, is its safeguard against blow out. One impor-

tant feature of the Oil Saver is its automatic ball release design. Hardened Steel

Balls hold the traveling assembly securely in the body until released by the

upward travel of the Rope Socket. The Rubber Packing unit with its internal fins

provide the ultimate in wire characteristics with only a normal pressure, or drag,

on the line.The Packing Rubber is compounded of special abrasive and oil resis-

tant properties to give the rubber longer wear. A tough spark-proof die cast alloy

is utilized in the top and bottom line guides and enhances reduced wear in the

rubber packing unit. A high quality leather hydraulic packing ring wards against

leakage in the area between the body and the traveling assembly.

The Steel Hydraulic Bonnet is Standard Equipment for Cavins Ball Lock Oil

Savers. The Hydraulic Bonnets provide an even greater degree of wiping effi-

ciency. The wire line can be completely stripped of all oil, or water and an Oil

Saver outfitted with a Hydraulic Bonnet foregoes the necessity of tools for “tak-

ing up” wear in the packing element. The one hand operation requires only a few

strokes of the pump handle to give complete wiping action or turn the release

valve when no wiping is required. The Hydraulic action affords a greater rubber

contact surface as the packing rubber is compressed around the line. The line is

completely surrounded and sealed from blow-out leakage by the action of the

Hydraulic unit. There is no danger of packing rubber or other elements falling

into the well.

The Ball-Lock Oil Saver is

standard with the popular

Steel Hydraulic Bonnet. It

is completely reliable for

efficient line wiping action

and is designed to reach

maximum utilization of the

Packing Rubber

The optional Hydraulic Bonnet is a self contained

unit and features a Bonnet pump and Handle for

ease of operation. Fig. 2

The Screw-Type Bonnet is available for Manual

Operation. Fig. 3

Fig. 4

Fig. 1

OIL WELL TOOLS

HYDRAULIC PUMP & HOSE

S-H500

S-1S-HP150

(Shown 4" S-15BX

with Remote Bonnet)

BLOW OUT PREVENTER

and ROD STRIPPER

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

The combination Blowout Preventer and Sucker Rod Stripper combines safety and economy in a tool designed to perform the

necessary function of line wiping. It can be operated from anywhere on the derrick floor utilizing pressure from bottled nitrogen,

an optional hand operated hydraulic pump, or the optional BOP control system (Fig. 1C). When this tool is employed of wire line

operations, a CAVINS Ball Lock Oil Saver is screwed directly into the top of the Blowout Preventer. When swabbing, a short lubri-

cator the length of the swab between the master gate and the Blowout Preventer is all that is required. The Blowout Preventer is

available in either the 3" size with full 3" ID clearance and 4" female. A.P.I. line pipe for the Ball Lock Oil Saver on top or the 4"

size with full 4" ID clearance and 4" female A.P.I. line pipe threads top and bottom. Pressure connection is for 1/4" A.P.I. pipe. The

units are tested to give full closure up to 3000 psi well pressure with no leakage. The full closure feature of the Blowout Preventer

will give a temporary seal, allowing ample time to close the master gate should a well blowout occur.

As a Sucker Rod Wiper, the unit affords exceptionally long wiping service and complete control of the well against possible

leakage or blowout. The rubber wiping unit is comparatively inexpensive and very easy to change.

B O P CONTROL SYSTEM

The BOP Control System provides the hydraulic power

and controls necessary to operate the Cavins Blow Out

Preventer and Rod Stripper during work-over operations

(Fig. 1C). Due to its compact design, the unit takes up little

space and also stores all accessories, controls and BOP

equipment. The BOP accumulator is powered by rig air (26

CFM @ 100 PSI) to charge and maintain pressure stored in

the system. The accumulator provides 3000 PSI + to the

BOP, which gives an immediate closure or it can be manu-

ally operated by a 2 stage hand pump for stripping opera-

tions. The BOP Control System can be configured a variety

of ways depending on what accessories or options are

required by the customer.

OIL WELL TOOLS

Fig. 1C

Fig. 1A

Blowout Preventer

Model S-BP50-A (3" I.D.)

Fig. 1B

Blowout Preventer

Model S-BP50-B (4" I.D.)

S-BP100

CEMENT DUMPS

Bridging Plugs and Quick-Change Rope Sockets

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

CAVINS – CEMENT DUMP

The CAVINS Cement Dump, a highly successful device is

attached to the lower end of any desired number of tubular sec-

tions, equipped with a rope socket immediately above the loading

window. The assembly is run on a Wire Line. The full opening of the

cement dump is closed by means of a thin, drillable disc, which is

positively released at any desired point in the well when the tool is

raised by the hoist operator. This permits the placing of any desired

amount of cement in a continuous operation. It eliminates the loss

of time involved by waiting for previous loads of cement to set up

and avoids the necessity of running into green cement on suc-

ceeding trips.

The cement slurry is discharged in a compact mass through the

full open dump with the assurance that it will not be diluted by the

well fluid. Fresh Water, sand mixed with oil, acid and concrete mix-

tures are readily dumped. The Cavins Cement Dump contains no

valves or other parts which might become fouled or clogged.

Accidental or premature unloading due to line whip or faulty brakes

is avoided by the amount of free travel built into the friction spring

assembly. The spring carriage is in its upper position when going

into the well carrying the load of Cement. When pulling the Cement

Dump up by the Wire Line, the friction springs retain the carriage in

its position against the casing wall. As the cement Dump moves

upward the carriage opens the toggles which hold the disc in place,

thus releasing the load.

TECHNICAL DATA

CAVINS “QUICK-CHANGE”

ROPE SOCKET

The CAVINS Quick-Change Rope

Socket is a swivel type socket which does

away with the necessity of having to bab-

bitt a rope socket to the sand line before

starting each job and then cutting it off

after the job is completed. Thus, it saves

considerable time and eliminates the haz-

ard of having to build fires near the well to

melt the babbitt. A small steel thimble,

which has a pull test of greater than 50%

of the strength of the wire line, is perma-

nently babbitted to the line. Alternately a

resin type Babbitt material is now available

which eliminates the need for open fire or

hotwork. The thimble is kept on the line at

all times and it is interchangeable with and

fits all sizes of Cavins Quick-Change Rope

Sockets. To remove one size socket from

the line and install another one, takes only

a few seconds time.

TECHNICAL DATA

NOTE: The above noted Box Connections are

standard Cavins Joints. Any type of Joint

can be cut on these Rope Sockets to

customer’s specifications.

CAVINS BRIDGING PLUGS

The CAVINS Bridging Plug is made of drillable material and is used to form

an off-bottom bridge on which cement, sand, and other materials can be

dumped. Canvas seal rings form a base onto which the material to be dumped

comes to rest when it is unloaded. Any tools used to drill out or break up

cement will easily destroy the Bridging Plug. It is set in the Casing by attach-

ing the disc on top of the Bridging Plug to the Cavins Cement Dump which is

used as a setting tool and lowered to the desired point.

Raising the Cement Dump releases the Fingers which have secured the

Plug to the bottom. When the Bridging Plug is thus released, notched dogs,

which are spring loaded and hinged to swing outwardly, are also released and

engaged with the Casing wall to secure the plug against downward movement.

Friction Brushes prevent ordinary movement of the plug until the engaging

dogs take hold.

DRILLABLE DISCS

OIL WELL TOOLS

.D.O gnisaC ni esU roFpmuD tnemeC

Size

"4/3-4 ot "4A-2"2/1-1

"8/5-7 OT "5A"2

"4/3-01 OT "8/5-6B"2/1-2

"61 OT "01C"3

Rope Socket O.D. Size of Box Connections

1-5/8 3/4 API Sucker Rod Box

1-3/4 3/4 API Sucker Rod Box

2 1 x 1-1/2–8 THD 3" Taper

2-1/4 1-1/8 x 1-3/4–8 THD 2-5/8" Taper

2-1/2 1-1/8 x 1-3/4–8 THD 2-5/8" Taper

2-3/4 1-1/8 x 1-3/4–8 THD 2-5/8" Taper

.D.O# traP

"8/3-1304-A2K

"2304-AK

"2/1-2304-BK

"4/1-3304-CK

Rope Socket

Sub

Cement

Dump

Coupling

Cement Dump

Window

Tr i p

Levers

Lugs

DISC

Drillable Discs used to Close

Bottom of Mandrel.

NAILS

NOTCHED

DOGS

1-3/8” O.D.

K2A403

2” O.D.

KA403

2-1/2” O.D.

KB403

3-1/4” O.D.

KC403

FRICTION

BRUSHES

Carriage

Friction

Springs

Bumper

Spring

Tubing

Thread

Bumper

Ring

Lock

Spring

Recess

Mandrel

Tube

Lock

Spring

WIRE

ROPE

CAP

LINER

(SPLIT)

ROPE

THIMBLE

BODY

Fig. 6

Coupling Retaining

Wire

Bridging

Plug

1-2 or 3 Lengths

of Tubing, as

Required

(Fig. 1)

(Fig. 4)

(Fig. 5)

(Fig. 2)

(Fig. 3)

RUBBER PRODUCTS

and ACCESSORIES

For Well Servicing Operators

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

Wire Line “Pig Tail” Wiper

OIL WELL TOOLS

Sucker Rod Wiper Holder

9", 12" & 14" Flat Pipe Wiper

(Flat Pipe Wiper Holders are also available)

10" Handle Bar Pipe Wiper

Tong Pullback Strap

Elevator Balancing Strap

Sucker Rod Wiper

WIRE LINE

NUT

WASHER

EYE BOLT

CHAIN

LID

NO. 10-0451

BODY

NO. 10-0457

RUBBER WIPER

NO. 10-0700

WIPING ELEMENT

CODE STUBBLE

CONVERTIBLE

CAT-LINE GRIP

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

REGULAR AND ROLLER TYPE MODELS

Purpose: To assure that the cat-line is held securely at any

desired point.

Description: The Cavins/BJ Convertible Cat-Line Grip has an

eccentric cam type grip shaped to the contour of conventional 1-

1/2" cat-line rope. The specially-shaped teeth, of this grip, when

locked against the braking horizontal face, take a positive grip with-

out damaging the cat-line rope.

Two Models: The Regular Model has direct access by the cat-line

rope to the cam type grip. The Roller Type Model has a special out-

board sheave that acts as a roller guide to give additional cat-line

control where particular installations may benefit from added direc-

tional control.

Special Convertible Feature: This Cavins/BJ Cat-Line Grip

design is engineered to be readily convertible to either right or left

hand gripping position both in Regular and Roller type models.

Change to right or left position is done by simply removing the

main pin holding the grip and control handle and switching the grip

and handle direction. Similarly, the outboard sheave on the Roller

Type model can be transposed, thus any Cavins/BJ Cat-Line Grip

model can be converted from Driller’s Side Right Hand Grip to

Automatic Cathead Side Left Hand Grip or visa-versa.

Additional Features: Both Regular and Roller Type Models are

additionally convertible in that the outboard roller sheave can be

added to the Regular Model by a simple bolt-on arrangement or

detached from the Roller Type Model when a Regular Type instal-

lation is desired.

Capacity: Both Regular and Roller Type models are designed to

handle a 6000-lb. working load.

Cavins/BJ Regular Type Convertible Cat-Line Grip

Cavins/BJ Roller Type Convertible Cat-Line Grip

OIL WELL TOOLS

SPECIFICATIONS–ROLLER TYPE

(RIGHT OR LEFT)

Order by Part Number and Part Name

SPECIFICATIONS–REGULAR TYPE

(RIGHT OR LEFT)

Order by Part Number and Part Name

Cavins/BJ Roller Type Convertible Cat-Line Grip

No. Part No. Part No.

dnaH thgiRdnaH tfeL.d’qeRemaN traP

Regular Cat-Line Grip Assembly 1 34700-1 34700

59643596431ydoB

36201362011pirG

72732727321reveL

1-562011-562011kcoL thgiR

19101191011kcoL tfeL

Socket Head Shoulder Screw 2 940585-37 940585-37

281-921749281-9217491niP lloR

No. Part No. Part No.

dnaH thgiRdnaH tfeL.d’qeRemaN traP

Roller Type Cat-Line Grip Complete — 34701-1 34701

Cat-Line Grip Assembly 1 34700-1 34700

59643596431ydoB

36201362011pirG

72732727321reveL

Right Lock 1 10265-1 10265-1

Left Lock 1 10191 10191

Socket Head Shoulder Screw 2 940585-37 940585-37

281-921749281-9217491niP lloR

Sheave Housing Assembly 1 34699 34699

Sheave Housing 1 34697 34697

Sheave Assembly 1 23620-1 23620-1

Sheave 1 31666 31666

Grease Fitting 1 940308-1 940308-1

Sheave Pin 1 23619 23619

Socket Head Cap Screw 2 941286-71 941286-71

3-24441493-2441492tuN kcoL

“T” SAFETY CLAMPS

2853 Cherry Avenue

Signal Hill, CA 90755

Ph: (562) 424-8564

Fax: (562) 595-6174

BAASH-ROSS®Type “T” Safety Clamps

The Type “T” Safety Clamp is designed for small diameter pipe

1-1/8" through 4-1/2" O.D. Each link changes the effective

working range approximately 1" in diameter.

The positive automatic gripping principle is ideal to help safe-

guard against dropping strings of flush tubing, to provide a

shoulder to position strings of flush line pipe for welding, and

many other applications.

TABLE NO. 1

Type T Safety Clamp Complete With Box

*These Parts are interchangeable with the “C” Type Clamps.

Recommended Spare Parts for remote locations–3 pieces Intermediate Link

(Item 2), 1 set Slips with retaining Cotter (Item 3), 3 pieces Link Pin with Cotter

(Item 5), 1 set Slip Springs (Item 4).

Baash-Ross is a licensed trademark of

National Oilwell Varco, L.P.

FIELD OFFICES

BAKERSFIELD, CA TAFT, CA VENTURA, CA

1519-32nd Street 815 Main Street 1641 N. Ventura Ave.

P.O. Box 2384 P.O. Box 695 Ventura, CA 93001-1577

Bakersfield, CA 93303-2384 Taft, CA 93268-3268 (805) 643-6767

(661) 327-7154 (661) 765-2181 Fax: (805) 643-1362

Fax: (661) 327-7155 Fax: (661) 765-2182

Printed In United States

OIL WELL TOOLS

A Division of DAWSON ENTERPRISES

2853 Cherry Avenue, P.O. Box 6039

Long Beach, CA 90806-0039

Ph: (562) 424-8564 • Fax: (562) 595-6174

E-mail: oiltools@cavins.com

CC 2002-03 (Rev. 2012) moc.snivac.www

Range O.D., Sizes

T thgieWtraP.d’qeR skniL .oN lato

Per Range From To Number Lbs. Each

4 1-1/8" 2" 7624-5044 84

5 2-1/8" 3-1/4" 7624-5045 88

6 3-1/4" 4-1/2" 7624-5046 92

Replacement Parts

thgieWtraP.oNmetI

hcaE .sbLrebmuN.d’qeRmetI.oN

1 Link Assembly, Complete

As Ordered

7624-B-7 4-1/4

2 Link, Intermediate 1 7624-A-18 3-1/4

3 Slip with Cotter 1 7624-A-21 1/4

3A Cotter, for Slip (1/4") 1 900620-52 1/4 oz.

4 Slip Spring 1 7624-B-21 1/2 oz.

5 *Link Pin with Cotter 1 7624-C-5 3/4

5A *Cotter, for Link Pin (3/16") 1 939672-36 1/4 oz.

6 End Link (Screw) 1 7624-A-20 4-1/2

7 End Link (Pivot Black) 1 7624-A-19 3-1/2

8 *End Link Pin with Chain 1 7624-F-5 1-1/4

9 *Screw 1 7624-A-5 4

2/1-15-B-42671tuN*01

11 *Nut Wrench 1 7624-A-25 3-1/2

12 *Pivot Block 1 7624-A-5000 1-1/2

13 *Pivot Block Pin 2 7624-D-5 1/4

14 *Pivot Block Pin Wrench 1 900533-12 1/8

15 Handle Assy. 1 7624-A-22 4

16 Handle Link Pin 2 7624-G-5 12 oz.

25 *Equipment Box 1 7624-A-9 45

53414

10 12 9

Cavins Cat 2012 T 4839 Ci Web

Navigation menu

Versions of this User Manual:

Views

Navigation