Celluon CL800BT English LASERKEY Manual
CL800BT to the manual 7e62d344-7a5b-96d4-118d-0acfca56c36f
User Manual: LASERKEY CL800BT
Open the PDF directly: View PDF 
.
Page Count: 66
| Download | |
| Open PDF In Browser | View PDF |
CL800BT MANUAL Safety Precautions Avoid long time expose to the direct light or heat. Faults may occur if kept in extreme of temperatures. May become damaged if dropped or knocked. Problems may occur if exposed to humid and/or dusty conditions. Do not use if power cable or plug are damaged. Use only dedicated cable/adapter. Do not disassemble. Do not look directly at the light source, as this can cause damage to the eye. 2 CL800BT MANUAL Regulatory Information FCC compliance Information This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Information to User This equipment has been tested and found to comply with the limits for a Class B digital device, Pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio Frequency energy and, if not installed and used in accordance with the instructions, may communications. cause However, harmful there interference is no to guarantee radio that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 3 CL800BT MANUAL - Redirect or reposition the receiving antenna - Increase the separation between the equipment and receiver - Connect the equipment to a socket on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC WARNING: This equipment may generate or use radiofrequency energy. Changes or modifications to this equipment may cause harmful interference, unless such modifications are expressly approved in the instruction manual. The user’s license to operate this equipment may be revoked if an unauthorized change or modification is made. RF Exposure Information: The antenna used for this transmitter must be installed at a distance of at least 20 cm from all persons and must not be co-located or operated in conjunction with any other antenna or transmitter. CE : EN300328 EN301489 EN60950 4 CL800BT MANUAL Laser Safety: Environmental Notice This product does not any materials specified harmful to the human body. At the end of this product’s service life, please separate with the life waste and discharge or go to the Celluon service center for environmental protection. 5 CL800BT MANUAL Battery Information Battery service life: 220 minutes continuous use (max) Capacity: 830mAh (max) @ 3.7V Charging the Battery Use the adapter supplied for connection to the power supply. The battery will now start charging. Charging time: 150 min Caution - Use of any other adapter may cause the battery to explode. - After purchasing the product, charge the battery before use. - Charging time is dependent on ambient temperature i.e. it may be longer or shorter in extreme heat or cold. - It is possible that the battery is not fully charged even when the charging indicator is illuminated. - Since battery belongs to expendable supplies, service life gradually shortens after several uses. 6 CL800BT MANUAL Table Contents 1. FEATURES...................................................................................9 2. COMPONENTS ..........................................................................10 3. PARTS AND THEIR FUNCTIONS .............................................11 3.1 FRONT .................................................................................. 11 3.2 REAR....................................................................................12 3.3 TOP ......................................................................................13 4. HOW TO OPERATE...................................................................14 4.1 INSTALLATION ..........................................................................14 4.2 IN BLUETOOTH MODE ............................................................15 5. HOW TO INSTALL, REMOVE AND USE SOFTWARE .............15 5.1 POCKET PC ............................................................................15 5.1.1 System Requirements .................................................15 5.1.2 Installation/Upgrading/Uninstalling the Driver ..............15 5.1.3 Connection Method......................................................18 5.1.4 Disabling the Projection Keyboard Sound ...................22 5.1.5 PK Settings Application................................................23 5.1.6 Tutorial .........................................................................33 5.1.7 Shortcut Icon Keys.......................................................34 5.1.8 Function Key and Ctrl Key ...........................................35 7 CL800BT MANUAL 5.2 PALM OS ............................................................................36 5.2.1 System Requirements .................................................36 5.2.2 Installation/Upgrading/Uninstalling...............................36 5.2.4 PK Settings ..................................................................44 5.2.5 PK Tutorial ...................................................................49 5.2.6 Shortcut Icon Keys.......................................................52 5.2.7 Shortcut Keys ..............................................................53 6. KEYBOARD LAYOUT................................................................55 7. TYPING LATIN LETTERS AND ADDITIONAL CHARACTERS .55 8. ADJUSTING KEY SENSITIVITY................................................58 9. SAFETY PRECAUTIONS ..........................................................60 10. TROUBLESHOOTING .............................................................62 11. SPECIFICATIONS AND DEMENSIONS ..................................64 8 CL800BT MANUAL 1. Features Uses normal QWERTY keyboard layout. Compact size (convenient to carry). Includes function and shortcut icon keys. Robust and durable, uses optical technologies Bluetooth and serial port interface connections. Rapid entry keys. Economical, uses an integrated, rechargeable lithium battery. Compatible with Pocket PC, Palm OS and Windows. 9 CL800BT MANUAL 2. Components Laserkey Installation CD Case Quick Install Guide Adapter Serial cable is optional. (refer to http://www.celluon.de.) CDs: - CL800BT Manual - Palm Driver Installation File - Pocket PC 2003 Driver (Widcomm Bluetooth Stack) Installation File) - Pocket PC 2003 Driver (Microsoft Bluetooth Stack) Installation File) 10 CL800BT MANUAL 3. Parts and their Functions 3.1 Front Pattern Projector Sensor Module Infra Red Light Source Projector: projects the keyboard image. Infra Red Light Source: supplies the light source to allow the Sensor Module to recognize key strokes. Sensor Module: recognizes key strokes and transmits them to the processing device. 11 CL800BT MANUAL 3.2 Rear Power Switch Comm. & Power Ports POWER UP / DOWN Æ ON / OFF Switch Communication & Power Ports Serial Port RC232C Cable Power Port 1A @ 5V adaptor Only use the cable / adapter supplied. 12 CL800BT MANUAL 3.3 Top Communication & Battery Power Status LED Status Battery Status LED o Charging Æ Red o Fully Charged Æ Green o Battery Power Low Æ Orange o (Power off within 5 minutes.) Communication & Power Status LED o Bluetooth Mode Pairing : Blue flashing Link: Blue o Serial Mode LED Green 13 CL800BT MANUAL * What is Bluetooth? Standard wireless communication between wireless communication devices using low power and over short distances. Note: When you want to exit from using Pocket PC and CL800BT with Bluetooth communication setting, exit by using Pocket PC own keyboard. (Due to operating error, it may reset Pocket PC). 4. How to Operate 4.1 Installation 1. Install software as described in “Manual 5”. 2. Turn power on. 3. Connect device to computer via cable. 4. Run program as described in “Manual 5” for environment setup. 5. Use laser keyboard. 14 CL800BT MANUAL 4.2 In Bluetooth Mode 1. Install software as described in “Manual 5”. 2. Turn power on. 3. Set up Bluetooth environment as described in “Manual 5”. 4. Use laser keyboard. 5. How to install, remove and use software 5.1 Pocket PC 5.1.1 System Requirements 1. Microsoft Windows 2000/XP operating system. 2. Microsoft ActiveSync 3.6 or above. 3. Pocket PC based on Microsoft Windows Mobile 2003, with Bluetooth (Widcomm or Microsoft). 5.1.2 Installation/ Upgrading/ Uninstalling the Driver For serial port drivers please refer to http://www.celluon.de. 15 CL800BT MANUAL 1. Installation 1) Connect PC to Pocket PC via ActiveSync. 2) Insert installation CD into the CD-ROM drive of your PC to start the installation program. 3) Follow installation program instructions. 2. Upgrading Download and install a new driver from http://www.celluon.de. 3. Uninstalling 1) Select Today Æ Settings Æ System Æ Remove Programs as shown in Figure 1. 16 CL800BT MANUAL Figure 1. Uninstalling the Driver 2) Choose Projection Keyboard and click Remove, as shown in Figure 2. Follow the on-screen instructions. Figure 2. Uninstalling the Driver 17 CL800BT MANUAL 5.1.3 Connection Method To connect a Pocket PC to the Projection Keyboard follow the instructions below. 1. Turn on power to Pocket PC and Projection Keyboard. Note: Verify that sufficient battery power is supplied to the Projection Keyboard device 2. Run the program required to enter the keyboard as shown in Figure 3 (e.g. Note). Figure 3. Running the Program 18 CL800BT MANUAL 3. Select Projection Keyboard from the options, as shown in Figure 4. Figure 4. Selecting a Device 19 CL800BT MANUAL 4. When the Bluetooth Browser is open, choose CL800BT, as shown in Figure 5. Figure 5. Selecting a Bluetooth Device 20 CL800BT MANUAL 5. You are now ready to use the Projection Keyboard. To change the Projection Keyboard’s set values, click on the Projection Keyboard icon to view the control panel, as shown in Figure 6. This icon Figure 6. Projection Keyboard Control Panel 21 CL800BT MANUAL 5.1.4 Disabling the Projection Keyboard Sound When the user clicks the keyboard sound icon, a clicking sound is emitted from the Pocket PC. To turn off the sound, click the keyboard sound button once; click again to turn it back on, as shown in Figure 7. This icon Figure 7. Keyboard Sound Icon 22 CL800BT MANUAL 5.1.5 PK Settings Application Click on the settings icon to change the different setting values on the Projection Keyboard, as shown in Figure 8. This icon Figure 8. PK Settings Icon Click the settings icon to view the Change Settings screen, as shown in Figure 9. These settings enable the user to adjust key repeat, key sound and key sensitivity. 23 CL800BT MANUAL 5.1.5.1 Main Change Settings Tab Figure 9. Main Change Settings Tab Key Repeat By using Key Repeat, continuously pressing a key causes the value to be entered repeatedly. Select the Key Repeat checkbox to use the key repeat function or deselect to disable the function. 24 CL800BT MANUAL Keyboard Sound Clicking the Keyboard Sound function causes a clicking sound to be emitted from the Pocket PC. Select the Keyboard Sound checkbox to turn on the key sound function or deselect it to disable the function. Sensitivity If the Projection Keyboard has a problem with key sensitivity, adjust the setting using the slider. For details, see “8. Adjusting Key Sensitivity”. Restoring Defaults To restore all functions to their default values, click the Restore Defaults button. 25 CL800BT MANUAL 5.1.5.2 Power Save Mode Adjust the Power Save Mode from the Power tab on the Change Settings screen. Power Save Mode On Click on the Power Save Mode On checkbox to use this function, as shown in Figure 10. Figure 10. Power Save Mode 26 CL800BT MANUAL Standby Change the Standby setting value to alter the time elapsed before the system enters Standby mode. In Standby mode, if no keys are pressed within a given period of time the device will enter a low power mode until a key is pressed again. Figure 11. Standby Mode 27 CL800BT MANUAL Wakeup Response To use the keyboard again, press any key or area of the keyboard. Change the Wakeup Response settings to adjust the speed for switching between Standby and normal mode, as shown in Figure 12. Figure 12. Wakeup Response 28 CL800BT MANUAL Turning Off the Projection Keyboard Once in Standby mode, if no keys are pressed within the time specified in the Turn Off After field, the device will enter Power OFF mode, as shown in Figure 13. To use the keyboard from Power OFF mode, turn the Projection Keyboard on again. Figure 13. Power OFF Mode Time Setting Restoring Defaults To restore the settings in the Power tab to their default values, click the Restore Defaults button. 29 CL800BT MANUAL 5.1.5.3 Projection Control Adjust keyboard brightness using the settings in the Projection tab. Projector Normal Adjust the keyboard brightness using the slider for the Projector Normal setting, as shown in Figure 14 Figure 14. Projector Normal 30 CL800BT MANUAL Projector Standby Mode Change the settings in the Projector Standby box to set the keyboard brightness in Standby mode, as shown in Figure 15. Figure 15. Projector Standby Restoring Defaults To restore the settings in the Power tab to their default values, click the Restore Defaults button. 31 CL800BT MANUAL 5.1.5.4 Driver Information Driver information for the Projection Keyboard is located under the About tab in the Settings screen, as shown in Figure 16. Figure 16. Driver Information 32 CL800BT MANUAL 5.1.6 Tutorial Click the Tutorial icon in the Projection Keyboard control panel to launch the Projection Keyboard Tutorial, as shown in Figure 17. The Tutorial offers information on how to use the Projection Keyboard. This icon Figure 17. Projection Keyboard Tutorial 33 CL800BT MANUAL 5.1.7 Shortcut Icon Keys Table 1.1 below shows the description for each icon. Icon Functions Switch to Today screen Run To Do program Run Mail program Run Find program Run Web Browser Run Calculator program Run Calendar program Run Address program Table 1.1 Shortcut Icon Keys 34 CL800BT MANUAL 5.1.8 Function Key and Ctrl Key Table 1.2 shows FN and CTRL key combinations. Key FN CTRL Shortcut Key Functions FN - 1 Run Note program FN - ENTER Close the current program FN - ← (Left Arrow) Home FN - → (Right Arrow) End FN - ↑(Up arrow) Page Up FN - ↓(Down Arrow) Page Down CTRL - Z Undo CTRL - X Cut CTRL - V Paste CTRL - C Copy CTRL - A Select All CTRL - U Underline CTRL - N Application Specific CTRL - S Application Specific CTRL - F Application Specific CTRL - Q Application Specific Table 1.2 Key Combinations 35 CL800BT MANUAL 5.2 Palm OS 5.2.1 System Requirements 1. Microsoft Windows 2000/XP operating system. 2. HotSync software. 3. Palm OS 5 or later. 5.2.2 Installation/ Upgrading/Uninstalling For the serial port driver, please refer to http://www.celluon.de or http://www.plawa.com. Installation 1. Insert CD into the CD-ROM drive of the PC to run the installation program. 2. Follow the on-screen instructions to install the program. Upgrading Find out above new drivers by referring to http://www.celluon.de and downloading drivers for installation. 36 CL800BT MANUAL Uninstalling 1. Select App Æ Delete, as shown in Figure 18. Figure 18. Uninstalling the Program 37 CL800BT MANUAL 2. Select PK Settings and click Delete… , as shown in Figure 19. Delete the PK Tutorial using the same method. . Figure 19. Deleting PK Settings 38 CL800BT MANUAL . 5.2.3 Establishing a Connection with the Projection Keyboard To establish a connection between a Palm device and the Projection Keyboard, please follow the instructions below. 1. Turn on the Palm device and the Projection Keyboard. Note: Check that sufficient battery power is supplied to the Projection Keyboard device. 2. Click the PK Settings icon to run the program, as shown in Figure 20. Figure 20. PK Settings Program 39 CL800BT MANUAL 3. On the Palm Bluetooth device screen, select Current Discovery in the Show items, as shown in Figure 21. Figure 21. Showing Bluetooth Devices 40 CL800BT MANUAL 4. Select CL800BT, as shown in Figure 22. Figure 22. Selecting CL800BT 41 CL800BT MANUAL 5. Click the OK button. The system will display a Connecting screen, as shown in Figure 23. Figure 23. Connecting to Bluetooth 42 CL800BT MANUAL 6. Once the Palm device and Projection Keyboard are connected, a tutorial screen is displayed, as shown in Figure 24. Figure 24. Tutorial 43 CL800BT MANUAL 5.2.4 PK Settings Once the Palm device and Projection Keyboard are connected, run the PK Settings program again to change the Projection Keyboard settings. 5.2.4.1 Main Screen Select the Main screen to view Settings, as shown in Figure 25. You may set the following functions: Figure 25. Main Screen 44 CL800BT MANUAL Key Repeat By using Key Repeat, continuously pressing a key causes the value to be entered repeatedly. Select the Key Repeat checkbox to use the key repeat function or deselect to disable the function. Keyboard Sound Clicking the Keyboard Sound function causes a clicking sound to be emitted from the Pocket PC. Select the Keyboard Sound checkbox to turn on the key sound function or deselect it to disable the function. Sensitivity If the Projection Keyboard has a problem with key sensitivity, adjust the setting using the slider. For details, see “8. Adjusting Key Sensitivity”. Restoring Defaults To restore all functions to their default values, click the Restore Defaults button. 45 CL800BT MANUAL Disconnecting To disconnect the Palm device from the Projection Keyboard, click on the Exit button. 5.2.4.2 Power Save Screen In the Power Save menu, you can change settings related to power consumption, as shown in Figure 26. Figure 26. Power Save Mode 46 CL800BT MANUAL Power Save Mode Select the Power Save Mode Off checkbox to disable Power Save Mode, or deselect the checkbox to run Power Save Mode. Standby Mode Change the Standby setting value to alter the time elapsed before the system enters Standby mode. In Standby mode, if no keys are pressed within a given period of time the device will enter a low power mode until a key is pressed again. Wakeup Mode To use the keyboard again, press any key or area of the keyboard. Change the Wakeup Response settings to adjust the speed for switching between Standby and normal mode. Power OFF Mode Once in Standby mode, if no keys are pressed within the time specified in the Turn Off After field, the device will enter Power OFF mode, as shown in Figure 13. To use the keyboard from Power OFF mode, turn the Projection Keyboard on again. 47 CL800BT MANUAL Restoring Defaults To restore the settings in the Power tab to their default values, click the Restore Defaults button. 5.2.4.3 Projector Screen Adjust the brightness of the keyboard on the Projector menu, as shown in Figure 27. Figure 27. Projector Screen 48 CL800BT MANUAL Power Save Mode Shows whether the Power Save option is turned on or off. Keyboard Brightness Change the Projector Normal slider to adjust the keyboard brightness. Keyboard Brightness in Standby Mode Change the Projector Standby slider to adjust the keyboard brightness when in Standby mode. Restoring Defaults To restore the settings to their default values, click the Restore Defaults button. 49 CL800BT MANUAL 5.2.5 PK Tutorial Click the PK Tutorial icon to launch the tutorial. You can view information on how to use the Projection Keyboard within the tutorial, as shown in Figure 28. 50 CL800BT MANUAL Figure 28. PK Tutorial 51 CL800BT MANUAL 5.2.6 Shortcut Icon Keys Table 2.1 shows the description for each icon. Icon Functions Switch to Today screen Run To Do program Run Mail program Run Find program Run Web Browser Run Calculator program Run Calendar program Run Address program Table 2.1 Icon Keys 52 CL800BT MANUAL 5.2.7 Shortcut Keys Table 2.2.lists the FN and CTRL key combinations. Key Key Combination FN FN - 1 Functions Run Memo Pad Program FN - 2 Run Voice Memo Program FN - F Select Font FN - K Launch PK Settings application FN - R Cmd + R FN - Y Cmd + Y FN - I Cmd + I FN - D Cmd + D FN - B Cmd + B FN - N Cmd + N FN - ←(left Arrow) Home FN - →(Right Arrow) End FN - ↑(Up Arrow) Page Up 53 CL800BT MANUAL CTRL FN - ↓(Down Arrow) Page Down CTRL - Z Undo CTRL - X Cut CTRL - V Paste CTRL - C Copy CTRL - A Select All CTRL - U Undo CTRL - S Select All CTRL - F Find CTRL - P Paste Table 2.2 Key Combinations 54 CL800BT MANUAL 6. Keyboard Layout Key layout of Projection Keyboard is as follows. 55 CL800BT MANUAL 7. Typing Latin Letters and Additional Characters FIRST FN - ' FN - SHIFT - 6 FN - SHIFT - ; FN - ` FN - SHIFT - ` SECOND A E I O U Y Á É Í Ó Ú Ý á é í ó ú ý Â Ê Î Ô Û N B Remark C / P S T D + R § ™ ˚ ± ® SHIFT SHIFT â ê î ô û Ä Ë Ï Ö Ü Ÿ ä ë ï ö ü ÿ À È Ì Ò Ù à è ì ò ù SHIFT SHIFT Ã Õ Ñ ã õ ñ SHIFT Å FN - O SHIFT å Ç FN - , SHIFT ç Ø FN - / SHIFT ø FN - E Æ Œ æ œ SHIFT ¶ FN - S Symbol SHIFT µ FN - C € ß ¥ 56 © ¢ ¿ £ Currency CL800BT MANUAL Key input e.g. 1) to input "Á" character: Press FN key and ' key simultaneously. Release both keys. Press SHIFT and A simultaneously. Key input e.g. 2) to input " ñ " character: Press the FN key, SHIFT key and ` key simultaneously. Release keys. Press N. Key input e.g. 3) to input "€" character: Press FN key and C key simultaneously. Release both keys. Press E. 57 CL800BT MANUAL 8. Adjusting Key Sensitivity The Projection Keyboard determines key input based on the amount of light reflected from the finger. Since the perceived amount of light changes depending on the surrounding environment, key sensitivity should be set according to userspecific conditions. How to Adjust Key Sensitivity 1. Click Sensitivity on the settings screen. 2. Adjust the Sensitivity slider. Check if a key stroke is recognized by pressing the center of the space bar key. Key Sensitivity Setting Factors Skin color Thickness of fingers Typing habit (leaning on keys) Finger accessories (manicure etc.) Surrounding environment 58 CL800BT MANUAL Caution - Key sensitivity must be adjusted each time a new user accesses the keyboard according to the new user’s requirements. - To ensure correct operation, avoid extreme light sources. - Relevant environmental factors include: - Direct sunlight, artificial light, Infra Red Data Association (IrDA), remote control devices. 59 CL800BT MANUAL 9. Safety Precautions Never look directly at the light source. Avoid direct sunlight or high levels of infrared rays. Do not use in extreme brightness. Do not use under very bright incandescent light. Do not insert conductive material into the device, or damage the power or communication ports. Do not strike or knock the device as this may cause damage or operational failure. Do not disassemble the device. (After Sales Service will not be available) Only use the cable/charging adapter supplied. High pressure or heat may cause the lithium battery to explode. Remove all objects on the surface between the device and the keyboard. Use on a flat surface. Avoid glass or transparent surfaces. Fingers should not be positioned less than 5 mm from the surface. Do not operate or store in high temperature or humidity. Do not submerge in water. It is not possible to get After Service for battery failure 60 CL800BT MANUAL caused by water. (Determined by color on the attached sticker.) 61 CL800BT MANUAL 10. Troubleshooting The device will not turn on. Cause: Discharged battery. Solution: Charge the battery fully. Key strokes not recognized even though the keyboard is connected. Cause: Sensitivity set too low. Solution: Reset to higher sensitivity and restart the device. Keyboard image is not visible even though the keyboard operates. Cause: 1. When brightness is set low, standby or off 2. The device is not charged. Solution: 1. Set brightness high, normal or on 2. Charge the device. Cause: The device is overheated. Solution: Move it to cooler surroundings and wait for a short time before restarting. Cause: The device was not positioned on a flat surface. 62 CL800BT MANUAL Solution: Move to a flat surface. Incorrect keys are recognized when typing. Cause: Sensitivity is set too high. Solution: Reset to lower sensitivity and restart the device. Cause: The device was not positioned on a flat surface. Solution: Move to a flat surface. 63 CL800BT MANUAL 11. Specifications and Dimensions Keyboard Project Items Specifications Light source Red Laser diode Keyboard layout 17mm QWERTY layout Keyboard size Approx. 241mm*106mm Keyboard position Approx. 100mm from keyboard device Projection surface Non-reflective, opaque flat surface Visibility Visible in 1000-5000 lux ambient light Keyboard Sensor Items Specifications Illumination Visible in incandescent light of 1800 lux or more Detection rate Up to 400 characters per minute Effective key stroke Approx. 2mm Operating surface Any flat surface 64 CL800BT MANUAL Electrical Condition Items Specifications Power source Integral lithium battery Battery capacity 830mAH(Max)@3.7V Adapter Rating 1A @ 5V Interface RS232C serial Bluetooth v1.1 class 2 Power consumption Max. 3W@5V Environmental Condition Items Specifications Operating temperature Approx. 0~35°C Storage temperature Approx. -20~50°C 65 CL800BT MANUAL Compatible Operating Systems Microsoft Windows Mobile 2003 Palm OS 5.x Microsoft Windows XP Size (mm): 93 * 39 * 37.5 Weight: 109g For information on device and driver compatibility, please refer to http://www.celluon.de or http://www.plawa.com. Technical Support: plawa-feinwerktechnik GmbH & Co. KG Bleichereistr. 18 73066 Uhingen Germany support@plawa.com Tel.: +49 7161 – 93 87 220 66
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 66 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:83932bdb-6a9e-4040-8308-8ee9847170f4 Producer : Acrobat Distiller 6.0 (Windows) Create Date : 2005:06:11 10:38:11+09:00 Creator Tool : PScript5.dll Version 5.2 Modify Date : 2005:06:11 10:39:32+09:00 Metadata Date : 2005:06:11 10:39:32+09:00 Document ID : uuid:31232c23-b28e-4a89-a50d-1276dfd80dcc Format : application/pdf Title : Celluon CL800BT English Creator : Author :EXIF Metadata provided by EXIF.tools