D817 2 Hpm 7 Day Digital Timer Instruction Sheet

User Manual: d817-2-hpm-7-day-digital-timer-instruction-sheet

Open the PDF directly: View PDF .
Page Count: 2

7 Day Digital Timer

Cat. D817/2

Instruction Manual

1Specification

To change from 12-hour display to 24-hour display, or vice

versa, press the CLOCK button and hold it until the LCD display

changes.

Please note that you can reset this digital timer at any stage by

removing the batteries.

2Time Display

Supply voltage 240V a.c.

Frequency 50Hz

Battery AAA size

Switching Current 10A max

Max Load 2400W

ON

DELAYCLOCK

AM MO

ON

OFF

TUWETHFRSASU

SET

S

AUTO

RND OFF

MODE

LCD Display

CLOCK Button

Button

S

Summer Time

DELAY Button RND Button

Socket

& Plug

MODE Button

Red

LED Light

Button

SET Button

Step 1: Press and hold the SET button until the day shown on the

LCD flashes.

Step 2: Use the and buttons to select the day of the week.

When correct, press SET to confirm the selection. The hour

figure on the display will flash

Step 3: Use and to select the correct hour. Press SET to

confirm your selection, and the minutes figure will flash.

Step 4: Use the and to set the minutes. Press SET to finish

setting the time. Press CLOCK to return to clock mode.

Step 5: The clock can be reset at any time by repeating steps

1 - 4. When setting the clock remember to use standard time.

See Daylight Saving (Summer Time) section for details on easily

switching between daylight savings (summer) time and standard

time.

3Setting the Day and Time

Step 2: Press SET to enter programming mode. The days of the

week at the top of the LCD screen will flash

Step 3: Press or to scroll through the day of the week

setting options. The day of the week setting options are listed

below:

MO TU WE TH FR SA SUN (this program will operate every day

of the week)

MO TU WE TH FR SA (this program will operate every day

except Sunday)

MO TU WE TH FR (this program will operate on weekdays only)

TH FR SA (this program will operate on Thu, Fri & Sat only)

MO TU WE (this program will operate on Mon, Tue & Wed only)

SA SU (this program will operate on Sat & Sun only)

TU TH SA (this program will operate on Tue, Thu & Sat only)

MO WE FR (this program will operate on Mon, Wed & Fri only)

MO

TU

WE

TH

FR

SA

SU

Once you are happy with your day/s selection, press SET to

confirm. The hour figure will now flash.

Step 4: Use or to select the time (hour) you want the

program to start. Press SET to confirm the setting - the minutes

figure will flash.

Step 5: Press or to select the time (minutes) you want the

program to start. Press SET to confirm.

Step 6: If you want to revise the day or time set repeat steps

1 - 5.

Step 7: When you are happy with the start time chosen, press

once to scroll to the program finish time. “1OFF” will be displayed

in the bottom left corner.

Step 8: Set the off day and time using the procedure in steps

2 - 5.

Step 9: To set another programme block press to scroll to

the next block. To finish programming press CLOCK to return to

clock mode.

4Setting the Timer

Step 1: To delete ALL pre-programmed settings remove the

timer from the mains power source and remove the batteries.

The clock will need to be reset when the batteries are replaced.

Step 2: To delete an individual timer setting, re-programme the

required block so the start and finish times are the same

OR

Scroll to the block you wish to delete and press the MODE button.

The display will change to --:--. To retrieve the setting press the

MODE button again.

5Deleting Programmes

There are 14 different programme blocks that can be set.

Step 1: To select the first block make sure the timer is displaying

the current time and press once. “1ON” will appear in the

bottom left corner.

6Using the Timer

Step 1: To use the timer plug it into a power source and plug an

appliance into the timer. Be sure to turn your appliance on.

(the program will only operate on the day selected)

http://waterheatertimer.org/Woods-timers-and-manuals-old.html#HPM

Warranty

HPM Cat D817/2 is warranted as here and after appears,

against faulty material and/or workmanship for a period

of one year from date of purchase. The obligation of the

manufacturer, under this warranty, is limited to servicing and

replacing defective parts when the unit is returned to HPM

Legrand, or the distributors in your state, freight pre-paid.

This warranty becomes void on any unit which has been

tampered with or damaged by accident, short circuited, loaded

beyond rating or damaged otherwise by improper operation.

The warranty is also conditional on the unit being installed by

a licensed electrical contractor. All other warranties, whether

expressed or implied, and whether arising by operation of lay

or otherwise are hereby excluded.

Customer Service

For all Customer Service and Technical Support

please call Monday to Friday during business hours.

HPM Legrand Australia

1300 369 777

www.hpmlegrand.com.au

HPM Legrand New Zealand

0800 476 009

www.hpmlegrand.co.nz

ABN: 31 000 102 661

26003A

SAFETY FEATURE: If there is a power failure, the timer is

unplugged or the wall socket is switched off (while the

batteries are installed and in good working order), the

programs and mode setting that you have entered will be

saved. When power is restored, if the timer was on and in

“AUTO” mode it will not resume the interrupted program and

will not turn back on until the next programmed “ON” time. If

in “OFF” mode the timer will remain off. If in “ON” mode the

timer will turn back on.

Step 2: Press the MODE button until the horizontal bar at the

bottom of the LCD is above the AUTO label - the timer will now

switch the appliance on and off according to the programmed

settings. The red LED indicates when there is power to the

appliance.

Step 3: You can override the timer settings:

a. Press MODE until the horizontal bar is over the ON label to

manually switch the appliance on

b. Press MODE until the horizontal bar is over the OFF label to

manually switch the appliance off.

Please Note: If you use the MODE button to turn your appliance

ON (or OFF) from AUTO mode, when you return to AUTO mode,

the appliance will remain ON (or OFF) until the next time it is

programmed to switch OFF (or ON).

This feature allows you to set your appliances to stay on or off for

a set time. For example, have a lamp remain off for 2 hours after

you leave home and then switch on, or an electric blanket stay on

for 30 minutes after you go to bed.

Step 1: Setting the timer delay function

a. To enter time delay mode, ensure the timer is in clock mode

and press .

“dON” or “dOFF” will be displayed in the bottom left

corner.

b. Press SET and ON or OFF will flash. If you want your appliance

to remain on for a set time press until “ON” flashes. If you

want the appliance to remain off for a set time, and then switch

on, press until “OFF” flashes. Press SET to confirm and the

hour will flash.

c. Use and to set the hours (0-99) for the time delay. Press

set to confirm.

d. Repeat step c. to set the minutes (0-59) and seconds (0-59).

e. Press CLOCK to return to clock mode.

Step 2: Using the timer delay function

a. Plug the timer in to a power source, and plug an appliance into

the timer. The delay function will only operate when the timer is

plugged into a power outlet.

b. Press the MODE button so the horizontal bar on the bottom of

the LCD moves and sits above the AUTO label.

c. Press the delay button to activate the delay function. To cancel

press the DELAY button again.

d. After pressing DELAY

“dON” or “dOFF” will flash in the bottom

left of the display. “dON” means the timer will remain on

7Time Delay Function

for the delay period programmed, “dOFF” means the timer will

remain off for the delay period programmed, and then switch on.

The Random Function will turn an appliance ON of OFF on an

irregular basis. Listed below are the criteria governing this

operation:

Minimum OFF time: 26 minutes

Maximum OFF time: 42 minutes

Minimum ON time: 10 minutes

Maximum ON time: 26 minutes

Step 1: To activate the randoom function ensure that the timer is

in clock mode and plugged into a power outlet.

Step 2: Press the MODE button until the horizontal bar sits above

the AUTO label.

Step 3: Press the RND button once. The bottom left hand corner

of the LCD will now show a flashing

“rOFF”. This indicates the

timer is now in Random mode and it will remain in the OFF

condition for a period anywhere between 26 to 42 minutes. It will

then switch on for a period anywhere between 10 to 26 minutes

and then switch off again.

Step 4: Pressing the RND button again will cancel the Random

Function.

8Random Function

The clock time can easily be changed from Standard Time to

Daylight Saving Time and vice versa with a simple operation.

Step 1: Press and hold the CLOCK button again followed by the

button to change from Standard time to Daylight Savings time.

The time will advance by one hour and the letter “S” will appear

on the top right hand corner of the LCD to indicate the Timer is

now in Daylight Saving time.

Step 2: Press and hold the CLOCK button followed by the

button to return the timer back to Standard time. The “S” will

disappear.

9Daylight Saving (Summer Time)

NOTE: If the batteries are flat or removed, the timer will not retain

previously set programs and mode settings. When new batteries

are installed, programs and mode settings will have to be reset.