D7016 DigiMux DVR Dvrh H264 Manual

User Manual: DVR

Open the PDF directly: View PDF PDF.
Page Count: 68

H.264 DVR system
H.264 DVR System
User’s Manual
DVR User’s Manual
1
DVR User’s Manual
2
Caution and Preventive Tips
Handle with care, do not drop the unit.
Mount the unit in an equipment rack or place it on a solid, stable surface.
Indoor use only. Do not place the unit in a humid, dusty, oily, or smoky site.
Do not place it in an area with poor ventilation or in an area close to fire or other sources of
heat. Doing so may damage the unit as well as cause fire or an electric shock.
When cleaning is necessary, shut down the system and unplug the unit from the outlet
before uncovering the top cover. Do not use liquid cleaners or aerosol cleaners. Use only
a damp cloth for cleaning.
Always shut down the system prior connecting or disconnecting accessories, with the
exception of USB devices.
Lithium battery: Danger of explosion if battery is incorrectly replaced. Replace with the
same or equivalent type of batteries recommended by the manufacturer. Dispose used
batteries according to the battery manufacturer’s instructions.
This symbol intends to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the
appliance.
This symbol intends to alert the user to the presence of unprotected “Dangerous
Voltage” within the product’s enclosure that may be strong enough to cause a
risk of electric shock.
DVR User’s Manual
3
Important Information
Before proceeding, please read and observe all instructions and warnings in this manual.
Retain this manual with the original bill of sale for future reference and, if necessary, warranty
service. When unpacking your unit, check for missing or damaged items. If any item is missing,
or if damage is evident, DO NOT INSTALL OR OPERATE THIS PRODUCT. Contact your
dealer for assistance.
Rack Mounting
Consult with the supplier or manufacturer of your equipment rack for the proper hardware and
procedure of mounting this product in a safe fashion. Avoid uneven loading or mechanical
instability when rack-mounting units. Make sure that units are installed to get enough airflow for
safe operation. The maximum temperature for rack-mounted units is 40 °C. Check product
label for power supply requirements to assure that no overloading of supply circuits or over
current protection occurs. Mains grounding must be reliable and uncompromised by any
connections.
DVR User’s Manual
4
Table of Content
1. Overview ....................................................................................................................... 4
2. System Setup ................................................................................................................ 8
2.1 Position the Unit ................................................................................................... 8
2.2 Selecting Video Format........................................................................................ 8
2.3 Connecting Devices to the Unit ............................................................................ 9
2.4 Rear Panel Connections ...................................................................................... 9
3. General System Setup ............................................................................................... 11
3.1 Front Panel Introduction .................................................................................... 11
3.1.1 LED Definition ...................................................................................... 11
3.1.2 Function Keys ....................................................................................... 12
3.2 Power Up / Down the Unit ................................................................................. 15
3.3 Entering OSD Setup Menu ................................................................................ 15
3.4 System Date / Time Setting ............................................................................... 16
3.4.1 Set Date / Time ..................................................................................... 16
3.4.2 Daylight Saving Time ............................................................................ 17
3.5 IP Camera Setting ............................................................................................. 18
3.5.1 IP Camera Information ......................................................................... 18
3.5.2 Connection Setup ................................................................................. 19
3.5.3 Device Setup ........................................................................................ 20
3.5.4 Activated............................................................................................... 20
3.5.5 Status ................................................................................................... 20
3.6 Record Schedule / Quality Setting ..................................................................... 21
3.6.1 Schedule Setup .................................................................................... 21
3.6.2 Preset Record Configuration ................................................................ 22
3.6.3 To Record Event Video Only ................................................................ 22
3.6.4 Per Camera Configuration .................................................................... 22
3.6.5 ezRecord Setup .................................................................................... 23
3.6.6 Circular Recording ................................................................................ 24
3.6.7 Purge Data ........................................................................................... 25
4. Basic Operation .......................................................................................................... 26
4.1 Viewing Live / Playback Video ........................................................................... 26
4.1.1 Viewing Modes ..................................................................................... 26
4.1.2 Digital Zoom ......................................................................................... 27
4.1.3 Viewing Live Cameras .......................................................................... 27
To Freeze Live Image ........................................................................... 27
4.1.4 Viewing Recorded Video ...................................................................... 27
Key Usage in Playback ........................................................................ 29
Pause Playback and Single Step Forward ........................................... 29
DVR User’s Manual
5
4.2 Sequence Setup ................................................................................................ 30
4.2.1 Sequence with Main Monitor ................................................................ 30
4.2.2 Sequence with Call Monitor .................................................................. 32
4.3 Searching Recorded Video ................................................................................ 32
4.3.1 Searching by Time ................................................................................ 33
4.3.2 Searching by Event .............................................................................. 33
4.4 Video Export ...................................................................................................... 34
4.4.1 ezBurn Introduction .............................................................................. 35
4.4.2 To Export Normal Video........................................................................ 35
4.4.3 To Export Event Video .......................................................................... 36
4.5 Dome Control ..................................................................................................... 36
4.5.1 Dome Connection ................................................................................. 38
4.5.2 Dome Protocol Setup ........................................................................... 38
4.5.3 RS485 Setup ........................................................................................ 38
4.5.4 Dome Controlling Keys ......................................................................... 39
4.5.5 Setting Preset Points ............................................................................ 40
4.5.6 Calling Preset Points ............................................................................ 41
5. Remote Monitoring Software ..................................................................................... 42
5.1 Remote Monitoring System Requirements ........................................................ 42
5.2 Getting Start of Installation................................................................................. 43
5.2.1 Changing Internet Settings ................................................................... 43
5.2.2 Installing Remote Monitoring Software ................................................. 45
5.2.2.1 Login / Logout ......................................................................... 46
5.2.2.2 Software Upgrades ................................................................. 47
5.3 Basic Operation for Monitoring Remotely .......................................................... 47
5.3.1 To View Live Video ............................................................................... 48
5.3.1.1 Selecting Display Mode .......................................................... 48
5.3.1.2 Operating Cameras with Dome Control .................................. 49
5.3.2 Instant Recording ................................................................................. 50
5.3.2.1 Recording Video Instantly ....................................................... 50
5.3.2.2 To Playback Instant Recorded Video ...................................... 50
5.3.3 To Playback Video ................................................................................ 51
5.3.3.1 Playing Back Remote Video .................................................... 51
5.3.3.2 To Playback Local *.drv Files .................................................. 52
5.3.3.3 Playback Controls ................................................................... 53
5.3.4 Search from Event List ......................................................................... 54
5.3.5 Take a Snapshot ................................................................................... 55
5.3.6 Remote Monitoring Software Trouble Shooting Guide ......................... 56
Appendix A: Technical Specifications ........................................................................... 57
Appendix B: Connect UTP Camera ................................................................................ 58
DVR User’s Manual
6
Appendix C: Connect Analog Camera via UTP Converter ........................................... 60
Appendix D: Recommended HDDs ................................................................................ 61
Appendix E: IP Camera Installation ...................................... Error! Bookmark not defined.
Appendix F: Remote Controller ...................................................................................... 62
Appendix G: Setting up a DVR behind a Router ........................................................... 65
DVR User’s Manual
7
1. Overview
The Optiview H.264 DVR is an integrated digital video recorder that
combines the features of a time-lapse audio / video recorder, a multiplexer,
and a video server to create a single security solution.
Its outstanding triplex operation enables users to view live video, search and
playback any recorded video by date/time or event, and remotely monitor the
unit via internet on PC, MEANWHILE the recording of the DVR unit is
ongoing simultaneously.
The Optiview H.264 DVR is enhanced to provide Dual-Codec including H.264
and MJPEG compression mode. Moreover, its distinctive hybrid solution
supports the coexistence of network compatible IP devices and convenient
analog connections. In addition to these sophisticated functions, another
marvelous implementation is the brand-new experience of Graphical User
Interface (GUI) that optimizes the monitoring controls of the unit.
The Optiview H.264 DVR is pre-installed with remote viewing and
configuration software, which is a Web-browser plug-in allowing users to view
live or recorded video images, and enables remote configuration. The remote
software is stored in the Optiview H.264 DVR and deployed over a LAN,
WAN or Internet connection to remote Windows-based computers. This
simplifies the installation and maintenance of the software components so all
remote users are using the same software coming from the unit.
The key features of the DVR are listed as follows.
Advanced Functions
Triplex Operation: Live, Record, Playback, Network
Supports up to 3 internal SATA HDDs
Supports internal DVD+RW
UTP Connection (Optional)
Dual-Codec for H.264 / MJPEG recording
Supports up to 2ch IP camera(s)
Supports recording of Megapixel IP camera(s)
Multi-language support
Multiple built-in dome camera control protocols
DVR User’s Manual
8
Supports Pre-Alarm Recording
Motion Detection Marker
Remote software for remote monitoring
Central Management System (CMS) for large-scale video management
Human Technology:
ezBurn™ for quick video export
ezRecord™ for quick recording setting
ezDDNS™ for automatic DDNS configuration
GUI interface
IR Remote Control (Optional)
Compact Control Keyboard (Optional)
2. System Setup
The notices and introduction on system installation will be described
particularly in this chapter. Please follow the description to operate the unit.
In order to prevent the unit from data loss and system damage that caused by
a sudden power fluctuation, use of an Uninterruptible Power Supply (UPS) is
highly recommended
2.1 Position the Unit
First, note to position / mount the DVR in a proper place and be sure to power
off the unit before making any connections. The placed location should avoid
hindering or blocking the unit from airflow. Enough airflow is needed to
protect the unit from overheating. The maximum allowable temperature of
operating environment is 40°C.
The unit utilizes heat-conducting techniques to transfer internal heat to the
case, especially to the bottom side of the unit.
NOTE: Be sure the rubber feet are not removed, and always leave a
space for air ventilation on the unit’s bottom side.
2.2 Selecting Video Format
The DVR is designed to operate under either NTSC or
PAL video formats. The switch is on the rear panel.
DVR User’s Manual
9
2.3 Connecting Devices to the Unit
This section lists some important notices that should be read before making
any connection to the DVR.
Connecting Required Devices
Before powering up the unit, cameras and a main monitor should be
connected to the unit for basic operation. If needed, connect a call monitor for
displaying full screen video of all installed cameras in sequence.
Connecting Short-term Device
If any short-term devices shall be installed to the DVR as parts of the unit
system, such as USB ThumbDrive® or any USB devices, etc, make sure
those devices are connected only after the unit is powered up. The reason is
because the DVR can recognize the external devices only after the power-up
process is done completely.
2.4 Rear Panel Connections
There are various connectors on the rear panel for the DVR installations. The
following figure shows the connectors by name; and followed by the detailed
description of each connector.
DVR User’s Manual
10
LAN Connector (RJ-45)
The DVR is capable of networking. Once the unit is
connected to the LAN network, users can remotely access
the unit through the remote software on a PC.
USB Connector (x3)
There are three USB 2.0 ports (2 at rear + 1 at front) to
allow users to connect external USB devices to the unit,
such as a USB ThumbDrive® or a USB mouse.
Power Jack
The DVR has a free voltage DC power connection jack.
Please connect the power adapter shipped with the unit.
Audio Out – Main & Call
Main & Call Audio Out RCA connectors are provided for
connecting the DVR to audio output devices (e.g.
amplified speakers). “Main” will output audio from the main
monitor, whereas “Call” will output audio form the call
monitor.
UTP Input (Optional)
The UTP Input offers additional connectivity
using the Unshielded Twisted Pair wiring.
UTP cable is one of the most common
medium in the telecommunication industry.
For UTP installation information, please
refer to Appendix B and Appendix C.
NOTE: UTP cable transmits Video and Power signals to cameras.
DVR User’s Manual
11
3. General System Setup
Before operating the DVR, some general configuration should be setup first.
The following subsections will introduce function keys on the front panel and
general configuration of the DVR.
The regular displayed OSD information and its displayed positions are shown
as following figure. The channel title will be displayed on the top-left side of
the window, either in full screen mode or in multiple channel mode. The
current operating mode, including Call mode, Dome Control mode, Playback
mode, Freeze mode and Sequence mode, will be displayed on the
bottom-left side of the screen. The date/ time information will be display on
the bottom-right side.
Ch4
►*1
2008/06/09 PM04:31:22
3.1 Front Panel Introduction
The front panel controls enable users to control the unit and preset the
programmable functions.
3.1.1 LED Definition
The LEDs on the front panel of the DVR are described as follows.
Power LED (Green)
The LED lights up when the correct power is connected to the unit.
Alarm LED (Red)
The LED lights up when an alarm is triggered.
Network LED (Green)
The LED lights up when the DVR is connected to a network and
blinks when the data is being transferred.
REC LED (Red)
The LED blinks while the DVR is recording.
DVR User’s Manual
12
3.1.2 Function Keys
This section describes the functional keys, which are for normal operation, on
the front panel of the DVR.
Please refer to the Setup Guide for the graphical illustration of functional
keys.
CHANNEL
In both Live and Playback modes, press the CHANNEL key to view the
corresponding video in full screen. The number of the CHANNEL keys
corresponds to the number of cameras supported by the unit.
In dome control mode, the key “1” is used to access the Set/Go preset
menu; the key “2” is used to hide or display the dome setting parameters.
Direction Keys
In Zoom mode, these keys function as Direction keys.
In the OSD setup menu, the LEFT/ RIGHT keys are used to move the
cursor to previous or next fields. To change the value in the selected field,
press UP/ DOWN.
ENTER / ZOOM
In OSD setup menu or selection interface, press this key to make the
selection or save settings.
In live full screen view mode, press this key to view a 2× zoom image;
press it again to exit Zoom mode.
COPY
In Playback mode, press COPY to select the start and end time of the export
video. Refer to Section Video Export for detailed information.
CALL
In Live mode, press this button to enter call monitor control mode.
In Dome mode, press CALL in association with ENTER to enter the OSD
setup menu of the dome camera. (See Dome Control section for more
information)
DVR User’s Manual
13
DOME
Press the key to enter dome control mode. Please refer to Section Dome
Control for detailed controlling operation.
ESC
Press to cancel or exit from certain mode or OSD setup menu without
changing the settings made previously.
MODE
Press repeatedly to select for wanted main monitor display format. There are
four available view modes: full screen, 4-window (2×2), 9-window (3x3), and
16-window (4x4). Refer to Section View Modes for detailed information.
PLAY
Press this key to switch between live image and playback video.
NOTE: The video of latest 5 ~ 10 minutes cannot be
played back because the video is still saved in the buffer.
FREEZE
Press FREEZE while viewing live image, the live video will be frozen. The
date / time information shown on the monitor will continue updating. Press
FREEZE again to return to live mode.
Press FREEZE while playing the recorded video, the playback video will
be paused. Press LEFT / RIGHT to move the recorded video reverse /
forward by single step. Press FREEZE again to continue playing video.
SEQ (Sequence)
Press to start automatic sequencing of the video coming from the installed
cameras.
MENU
Press this key to enter the OSD setup menu.
SEARCH
In both Playback and Live mode, users can press SEARCH to call the Search
menu for searching and playing back recorded video by date and time or
events.
DVR User’s Manual
14
DVR User’s Manual
15
3.2 Power Up / Down the Unit
If the DVR must be shutdown for any reason, please use the proper shut
down and power up procedures to avoid damaging the DVR.
To Power Up the Unit
Simply plug in the power adapter that came with the package and the DVR
will start to boot.
The color bar and system checking information will be shown on the monitor
and then disappear when the unit has been completely powered up.
To Restart / Shutdown the Unit
Press MENU and input the administrator password to access the OSD setup
menu. Select <Shutdown> in Main Menu and press ENTER to enter the
Shutdown menu, which displays as follows.
Shutdown
1. Power Off
2. Reboot
Execute
Execute
<Power Off>
Select this item to shut down the unit. Do not remove the power during shut
down until the message “You can safely turn off DVR now!” displays.
<Reboot>
Select this item to reboot the unit. The color bar and system checking
information are displayed on the monitor until the unit is completely restarted.
3.3 Entering OSD Setup Menu
The configuration of the DVR can be customized by entering the intuitive
Graphical User Interface (GUI) OSD setup menu. Collaborating with a USB
mouse, setting up the DVR can be easy as operating on a PC. Press MENU
and enter Administrator or User password to enter the OSD setup menu. The
Password Verification screen displays as follows.
Password Verification
________
Press Channel Keys To Enter Password
(4-8 Digits)
Press ◄ Key To Delete
DVR User’s Manual
16
The default passwords are shown in the following table. The same
passwords are used for entering the remote viewing software.
Administrator Password
User Password
1 2 3 4
4 3 2 1
NOTE: It is strongly suggested to change the
passwords to prevent unauthorized access to the unit.
3.4 System Date / Time Setting
Users can set the current date, time and other OSD parameters in Date/Time
menu (under System Setup Menu). The administrator’s privileges are
required for entering the submenu. In OSD setup menu, select <System
Setup> and press ENTER, then select <Date/Time> to access the Date/Time
menu; the menu displays as follows.
Date/Time
1. Date
2. Time
3. Date/Time Display
4. Date Display Mode
5. Time Display Mode
6. Date/Time Order
7. Daylight Saving Time Setup
2008/02/21
PM10:39:26
1 Row
Y/M/D
12 HR
Date First
3.4.1 Set Date / Time
Set Date / Time
Select <Date> / <Time> and press ENTER to adjust the settings. LEFT /
RIGHT keys are used to move the cursor to previous or next field, ENTER is
to select, and UP / DOWN are used to change the value in the selected field.
NOTE: The new date / time setting applies to
record new video. The date and time of previously recorded video
will not be changed.
NOTE: If time settings have to be changed in any
case, it is strongly recommended to format the HDDs to avoid
database corruption.
Date / Time Display
Users are allowed to set the time OSD displays in 1 or 2 rows. Use the UP /
DOWN keys to change the setting.
DVR User’s Manual
17
Date Display Mode
This function allows users to set the OSD display type of the date. There are
three options to select from: <Y/M/D>, <M/D/Y> or <D/M/Y>. “Y” represents
“Year”, “M” represents “Month” and “D” represents “Day”.
Move to the item and press ENTER, the option starts blinking. Use UP /
DOWN keys to change the setting.
Time Display Mode
Users can set the time format to <12 hour> or <24 hour>. Use the UP /
DOWN keys to change the format.
Date / Time Order
The item is used to set the order of date / time display to <Date First> or
<Time First>. Use UP / DOWN keys to change the setting.
3.4.2 Daylight Saving Time
Daylight Saving Time
The item is for those people who live in certain regions to observe Daylight
Saving Time. Select <ON> to enable, or <OFF> to disable the function.
If the function is disabled, the DST Start / End time and DST Bias will be
grayed out and cannot be accessed.
NOTE: If this function is enabled, the date/time information will be
shown on the screen with a DST icon when playing back recorded
video or searching video in the event list. “S” indicates summer time
and “W” indicates wintertime.
DST Start / End
The items are used to program the daylight saving duration. Use LEFT /
RIGHT keys to move the cursor to the next or previous field, UP / DOWN to
change the settings in the selected field.
DST Bias
The item allows users to set the amount of time to move forward from the
standard time for daylight saving time. The available options are in minutes.
DVR User’s Manual
18
3.5 IP Camera Setting
The distinctive hybrid solution of the DVR enables users to connect IP
camera(s) while others are analog cameras. First enter the OSD setup menu
with the administrator password and access <System Setup> <IP Camera
Support> to select the number of IP cameras to be connected. The supported
channels of IP cameras will be from the largest numbers, for example CH16
for 16ch models.
NOTE: The DVR must be rebooted in order to apply the change of
IP Camera Support option.
To configure setting of an IP camera, access <Camera Setup> and select the
channel with the largest number. The menu will be shown as follows.
IP Camera
1. IP Camera Select
2. IP Camera Title
3. Hostname/IP
4. Model
5. Connection Setup
6. Device Setup
7. Activated
8. Status
CH16
CH16
X.X.X.X
No
NOTE: If the IP camera is already activated, menu
items 3 to 5 will be grayed out and cannot be accessed.
3.5.1 IP Camera Information
IP Camera Title
Access this item to enter the name of the IP camera to be shown on the
monitor.
Hostname/IP
Access this item to enter the hostname or IP address of the IP camera, for
example 192.168.1.123.
Model
Access this item to select the model of the connected IP camera.
Formatted: Font: (Default) Arial, Bold
DVR User’s Manual
19
3.5.2 Connection Setup
Enter <Connection Setup> to configure the connection and data transmission
setting of the connected IP Camera. The menu will be shown as below.
Connection Setup
1. Account
2. Password
3. Management Port
4. Streaming Port
5. Streaming Format
6. Streaming Protocol
****
****
80
8090
MPEG4
RTP+RTSP
Account / Password
Access these two items to enter a valid account name and password of the
connected IP camera.
Management Port
Access this item to enter the default port of the IP camera.
Streaming Port
Access this item to enter the streaming port, for transmitting video and
related commands, of the IP camera.
Streaming Format
Access this item to select the streaming format, <MPEG4> or <MJPEG>, of
the IP camera.
Streaming Protocol
Access this item to select the streaming protocol of the IP camera. The option
includes <RTP+RTSP>, <RTP/RTSP>, <RTP/RTSP/HTTP>, and <HTTP>.
NOTE: Please contact manufacturer of the IP camera for assistance if
the IP camera’s Management Port / Streaming Port / Streaming
Format / Streaming Protocol are unknown.
DVR User’s Manual
20
3.5.3 Device Setup
Enter <Device Setup> to configure the basic settings of the IP camera. The
basic settings include the IP camera’s product name, image quality, image
adjustment, etc. Set the item <Apply> to <Yes> to apply the changes.
NOTE: The administrator account and password of the IP camera
should be entered in order to change the basic settings.
3.5.4 Activated
Access this item and select <Yes> to activate the connection to the IP camera.
To deactivate the connection, select <No>.
NOTE: Once the connection to the IP camera is activated, menu items
<Hostname/IP>, <Model>, and <Connection Setup> will be grayed out
and cannot be accessed.
3.5.5 Status
After the connection to the IP camera is activated, users can check the
connection status. The menu will be shown as below.
Status
1. Model
2. Resolution
3. PPS
4. Bandwidth
5. Pkg. lost rate
****
720*480
10
20 KB/Sec
0.1%
The information shown on the monitor is “read only”.
DVR User’s Manual
21
3.6 Record Schedule / Quality Setting
The Record Setup menu allows users to set recording quality, recording
schedules, and other recording parameters. Administrator's password is
required to access Record Setup menu. In the Main menu, move the cursor
to <Record Setup> and press ENTER; the following menu is displayed.
Record Setup
1. Record Mode
2. Schedule Setup
3. Preset Config
4. Per Camera Config
5. ezRecord Setup
6. Circular Recording
7. Purge Data
720×240@60PPS
Best Quality
ON
3.6.1 Schedule Setup
The Schedule Setup is used to set the day and night time, or weekend
recording schedule. Select <Schedule Setup> from the Record Setup menu
and press ENTER; the following menu is displayed.
Schedule Setup
1. Day Time Start
2. Day Time End
3. Night Time Start
4. Night Time End
5. Weekend Schedule
6. Weekend Start
7. Weekend End
AM 06:00
PM 06:00
PM 06:00
AM 06:00
ON
Fri 18:00
Mon
06:00
Make appropriate changes of the start time of Day and Night Time using
Direction keys.
Press ENTER to confirm the settings or ESC to cancel.
If a weekend record is required, select <ON> to enable the Weekend
Schedule in advance and then set the Weekend Start/End time.
Press ESC to return to previous page.
DVR User’s Manual
22
3.6.2 Preset Record Configuration
The <Preset Config> is used to select the preset recording quality and frame
rate. In normal circumstances, it is strongly recommended to set the preset
configuration as <Best Quality>. Below table shows the PPS and picture size
under <Best Quality> in Half-D1 mode. Please refer to OSD Menu Setup
Guide, Section Preset Record Configuration for more detailed information.
Halfl-D1 mode (NTSC: 720x240@60PPS; PAL: 720x288@50PPS)
Normal PPS
Normal Size
Event PPS
Event Size
3.75 NTSC
(3.125 PAL)
10 KB / Pic
15 NTSC
(12.5 PAL)
10 KB / Pic
3.6.3 To Record Event Video Only
If the DVR shall start recording only when alarms are triggered, follow the
steps below:
Enter the OSD setup menu with correct password.
In the OSD setup menu, select <Record Setup> menu. Move the cursor to
the item <Preset Config>, and select <Event only>.
Refer to OSD Menu Setup Guide, Section Preset Record Configuration for
more detailed information.
3.6.4 Per Camera Configuration
This function is used to set the Day / Night / Weekend PPS (Picture per
Second) and Quality for each channel. The Preset Configuration must be set
to <OFF> for accessing these schedules. The menu is displayed as below
(Record Mode: 720×240@60PPS in NTSC / 720×288@50PPS in PAL).
Per Camera Config
Cameral Select
Normal PPS
Normal Size
Event Max PPS
Event Size
Event Active
Day
15
Mid
30
Best
Both
Night
15
Mid
30
Best
Both
CH1
Weekend
15
Mid
30
Best
Both
DVR User’s Manual
23
First select a Camera for setting its record configuration. The image and
recording settings from the selected camera will be displayed on the
screen.
Move the cursor using Direction keys and press ENTER to select an item.
Change the value using UP / DOWN keys.
Press ENTER to confirm the settings or ESC to abort.
Press ESC to return to Record Setup menu.
Please note that the total normal PPS for all channels cannot exceed 60
NTSC (720×240@60PPS) / 50 PAL (720×288@50PPS). To increase one
channel’s PPS, others’ may have to be reduced first. Event PPS is not
restricted to this rule, since a smart event scheduler will handle the total PPS
with a correct weighting.
3.6.5 ezRecord Setup
This item aims to ease the complicated record settings, and to make the
setup much easier. Note that the item can be reached only when <ezRecord>
is selected as the option for <Preset Config>.
Select <ezRecord Setup> from <Record Setup> and press ENTER, the
sub-menu appears as below figure:
ezRecord Setup
How Many Days To Record
Daytime Record
Night Record
Weekend Record
Average Normal PPS
Average Normal Quality
2 Days
Yes
Yes
Yes
3.75
Best
Record Info
DVR User’s Manual
24
Follow these steps to Setup ezRecord:
Select <How Many Days To Record> and press ENTER, then press
UP/DOWN to choose an option. The average normal PPS & Quality will
be adjusted automatically. The maximum of days depends of the size of
the installed HDD(s). In other words, the larger the size of the HDD
installed, the more days the unit can record.
Move to <Daytime Record> and press ENTER. This item will determine
whether the DVR will record during daytime. If yes, use UP/DOWN to
select <Yes> as to enable daytime recording; or select <No> to disable.
Repeat the same procedures through the 3rd and 4th item, respectively.
Note that <Weekend Record> will be inaccessible if <Weekend
Schedule> in <Schedule Setup> is set to <No>.
Select <Average Normal PPS> and press ENTER, then press
UP/DOWN to make a choice. The <How Many Days To Record> will be
computed automatically.
Select <Average Normal Quality> and press ENTER, then press
UP/DOWN to make a choice. The <How Many Days To Record> will be
computed automatically.
NOTE: The current number of connected cameras
will affect the recording quality automatically calculated through
the <ezRecord Setup>. Therefore, once the number of connected
cameras is changed, the <ezRecord Setup> should be reset.
3.6.6 Circular Recording
Users can choose to record video in circular mode or in linear mode. If
circular mode is selected, the DVR will stores new video into the HDD spaces
while overwrite the oldest recorded video. Alternatively, if linear mode is
selected, the DVR will stop recording when the HDD is full and the internal
buzzer will start to beep.
From the Record Setup menu, move the cursor to <Circular Recording> and
press ENTER, then select <ON> / <OFF> using UP / DOWN keys.
DVR User’s Manual
25
3.6.7 Purge Data
This item is used to delete the Normal or Event recording video. In Record
Setup menu, move the cursor to <Purge Data> and press ENTER; the Purge
Data menu is displayed.
Purge Data
1. Purge All Data
2. Purge All Event Data
3. Purge Event Before
4. Start to Purge
No
No
2008/01/01
No
Purge All Data
The item is used to delete all recorded video from the database. Set this item
to <Yes using UP / DOWN keys, and start the deletion by setting <Start to
Purge> to <Yes>.
Purge All Event Data
The item is used to delete all event video from database(s). Using UP /
DOWN keys to select <Yes> and start the deletion by setting <Start to
Purge> to <Yes>.
Purge Event Before
The item is used to delete event video before a specific date. Use LEFT /
RIGHT keys to move the cursor to next or previous field, ENTER to select the
item and UP / DOWN to adjust the value.
Start to Purge
After the video or data to be deleted are selected, set this item to <Yes> to
start the deletion or choose <No> to cancel.
DVR User’s Manual
26
4. Basic Operation
The DVR allows users to access some general operations through the front
panel easily. The following sections introduce the general operations of the
unit.
4.1 Viewing Live / Playback Video
The general functions in live and playback mode are described in the
following sections.
4.1.1 Viewing Modes
The DVR provides users Optiview ways of viewing both live and recorded
video. Following presents these view formats.
Viewing in Full Screen
Press any CHANNEL key directly to view the corresponding camera image in
full screen format.
Viewing in Multi-window
Various multi-window view formats are offered for selection. To switch
between available viewing formats, press MODE repeatedly.
The available view formats are illustrated as the following figure.
NOTE: 3x3 and 4x4 viewing modes only available in 16-ch models.
DVR User’s Manual
27
4.1.2 Digital Zoom
Users are able to view a 2× full screen in live mode. To view the 2× full
screen, follow the steps.
Press any CHANNEL key to view the corresponding camera in full screen.
Press ENTER to view 2× zoomed screen of the selected camera.
To view a specific area in 2× zoomed screen, use Direction keys to pan /
tilt the zoomed screen.
Either press ENTER again or ESC to leave the Zoom mode.
4.1.3 Viewing Live Cameras
Users are allowed to view live camera in Optiview viewing modes, including
full-screen, 2×2, 3x3 and 4×4. The general operation under live mode is
described as follows.
To Freeze Live Image
Press FREEZE while viewing live image, the image pauses but the date /
time information does not, and the system clock continues running.
Press FREEZE to pause the live image; press FREEZE again to resume the
live camera view.
4.1.4 Viewing Recorded Video
To view recorded video, users can press PLAY key directly. After presssing
the PLAY key, the unit starts to continue playing back the recorded video from
the suspended point of record. If it is the first time to use the PLAY key, the
unit will playback from the very beginning of the record. Alternatively, users
can select records from the Search menu to play specific video. Refer to
section Searching Recorded Video for further information.
NOTE: When playing back videos with mass motion recorded in D1
mode (resolution=720x480), press SEQ key to switch on “deflicker
function” to avoid gleaming of images.
DVR User’s Manual
28
The Forward or Reverse speed indicator will be shown on the bottom-left of
the screen in the playback mode.
DVR User’s Manual
29
The general operations in playback mode are described as
follows.
Key Usage in Playback
The key usage is slightly different in playback mode. Following is the key
usage found in playback mode.
- LEFT (Reverse Playback)
The key is used to reverse the recorded video while the unit is playing
back. Press the key repeatedly to increase the speed of reverse
playback by 1×, 2×, 4×, 8×, 16×, or 32×.
- RIGHT (Forward Playback)
The key is used to play the recorded video fast forward. Press the key
repeatedly to increase the speed of forward playback by 1×, 2×, 4×, 8×,
16×, or 32×.
- FREEZE
Press FREEZE to pause the playback video. When the recorded video is
paused, press LEFT / RIGHT to resume playback video single step
reverse / forward, respectively. Press FREEZE again to continue playing
video.
- PLAY
Press it to start playing back video, exit current mode, or stop playing
back video and return to live mode.
Pause Playback and Single Step Forward
To pause and resume recorded video, follow these steps.
Press any CHANNEL key to view the corresponding camera in full screen.
Press FREEZE to pause the current playback image.
Press RIGHT / LEFT Direction keys to move the video single step reverse
/ forward. Press and hold RIGHT / LEFT keys to repeatedly reverse /
forward the video single step.
Press FREEZE again to resume the playback operation.
DVR User’s Manual
30
Viewing Live Image in Playback Mode
Press the MODE key repeatedly in playback mode, a 16-window viewing
mode contains both live and playback image appears. This viewing mode is
illustrated as the following figure.
The eight windows on the upper half of the screen playback the Live video
from channel 1 to channel 8 respectively, and the other windows allow users
to view Playback image from channel 1 to channel 8.
4.2 Sequence Setup
This section introduces the way to view sequence mode with both Main
Monitor and Call Monitor, if connected. Sequence function can avoid manual
backtracking and provides more flexibility while monitoring surveillance.
4.2.1 Sequence with Main Monitor
Automatic sequence function can be observed in any view mode. Select
certain view format and press SEQ to toggle the automatic sequence; press
ESC to stop sequencing. The figure below displays the 4-camera and
9-camera sequencing view modes.
4-
Formatted: Indent: Left: 0"
Formatted: Font: (Default) Arial, Font
color: Red
DVR User’s Manual
31
Formatted: Font: (Default) Arial
Formatted: Normal, Centered, Indent: Left
6 ch
Formatted: Bullets and Numbering
DVR User’s Manual
32
4.2.2 Sequence with Call Monitor
Users are allowed to use the DVR front panel to control a call monitor display
without having to access the Main menu. Two viewing modes can be
displayed on call monitor: Sequence display and Single camera display. To
program the call monitor sequence, see OSD Menu Setup Guide, Section
Sequence Setup.
Follow the steps to control the call monitor.
Press the CALL key on the front panel to enter call monitor control mode.
The message “Call Mode” will be shown on the bottom-left of the screen.
Press 1-16 Key To Select Channel
Press SEQ To Enable Sequence
Call Mode
Press CHANNEL key to display the associated camera on call monitor.
Alternatively, press SEQ repeatedly to display the sequence of cameras
previously programmed in Call Monitor Schedule menu.
Press ESC to return the front panel to Main monitor control mode.
4.3 Searching Recorded Video
The DVR is capable of searching and playing back recorded video by date
and time or events. Enter the specific date and time of the wanted video, the
DVR will search for matched video and start to playback the video.
Alternatively, users can search for event video by channel as well.
In live or playback mode, press SEARCH to enter the Search menu, which is
shown as follows.
Search
----------------------------Search By Time----------------------------
From:
End:
Select:
2008/01/01 00:00:00
2008/05/01 00:00:00
2008/01/01 00:00:00
Begin Playback
----------------------------Search By Event----------------------------
Select Channel:
CH1 CH2 CH3 CH4
Event List
Formatted: Font: (Default) Arial, Font
color: Black
Formatted: Normal, Justified, Indent: Left
6 ch, Tab stops: Not at 1"
Formatted: Font color: Black
DVR User’s Manual
33
4.3.1 Searching by Time
Follow the steps to search video by date and time.
Press SEARCH key to enter the Search menu.
Move the cursor to “From Time” and press ENTER will start playing
recorded video from the specified “From Time”.
Move the cursor to “End Time” and press ENTER will start playing
recorded video from the specified “End Time”.
Use Direction keys to move the cursor for setting the start time. Adjust the
date and time values by UP / DOWN keys.
Press ENTER to confirm the settings or ESC to abort.
Move the cursor to <Begin Playback> and press ENTER to start playing
back the selected video.
Either press PLAY again or ESC to return to live video.
NOTE: If there is no available recorded video that matches the
specified time and date, the unit starts playback from the next
available video.
NOTE: The date/time information will be shown on the screen
with a DST icon if the Daylight Saving Time function is enabled. “S”
indicates summer time and “W” indicates winter time.
4.3.2 Searching by Event
“Event List” allows users to search wanted video by event. The Event List is
displayed as below figure:
Event List
First Page
Date Time
2008/03/17 11:26:50
2008/03/17 09:53:03
2008/03/16 16:14:42
2008/03/15 03:45:31
2008/03/12 22:27:56
2008/03/12 10:09:29
2008/03/11 12:18:20
2008/03/10 05:16:00
2008/03/08 17:11:37
2008/03/08 16:29:10
2008/03/08 03:22:17
Ch.
2
5
3
1
1
7
6
4
2
8
2
Type
Motion
Alarm
Alarm
Motion
Alarm
Motion
Motion
Alarm
Motion
Motion
Alarm
DVR User’s Manual
34
The list displays events by date, time, triggered camera and alarm type. As
some events are deleted, others are displayed. The latest recorded event
video will be listed on the top.
Follow these steps to search event video through Event List:
Press SEARCH to enter the Search menu.
To search event video that has been recorded on a specific camera, use
LEFT / RIGHT to move the cursor and press ENTER to select or de-select
a channel.
Move the cursor to <Event List> and press ENTER to list the event video
of the selected channels. The Event List displays.
To exit the event list, press ESC.
Follow the steps to playback video from Event List.
Press and hold UP / DOWN to scroll through the Event List.
Press ENTER to play back the selected event record.
Press PLAY to return to live mode.
4.4 Video Export
The unit allows users to export wanted video to the built-in DVD+RW or an
external device, such as a USB ThumbDrive, and the exported video will be
saved as *.drv file.
If the video is to be exported to an external device, make sure the device is
connected to the DVR unit and the port has been set appropriately for video
export.
NOTE: Once an external device is connected to the DVR
unit, the device has priority over the built-in DVD+RW, which means
that the wanted video will be exported to the external device instead of
the built-in DVD+RW.
According to the size of video, the export may take about 10 minutes to 1
hour.
DVR User’s Manual
35
4.4.1 ezBurn Introduction
Built with the ezBurn technology, ezBurn function provides users the easier
way to export desired video with built-in DVD+RW or to an external device,
such as an USB ThumbDrive®.
TWO keys (SEARCH and COPY) and THREE touches are all what’s needed
for completing the export. The entire exporting process will be done through
the front panel, without needing to enter the OSD setup menu.
The ezBurn exporting process is illustrated as below figure:
The entire process is described step by step in the following sections.
NOTE: The file exported using ezBurn will be in .drv file format, and
it can only be played using the remote player software.
4.4.2 To Export Normal Video
To Export normal video to external device, follow these step:
Press SEARCH and play wanted normal video by entering date and time.
Note if the screen is showing in multiple channel mode, please make sure
there is no window displaying in Live mode, or the export will not work.
After entering playback mode, play the video and press COPY once to
mark the starting point of the export video. The playback continues.
Press COPY again to mark the ending point of the export video. Then the
“ezBurn” window will display as below figure. The information shown on
the window is “read only”.
ezBurn confirmation
Selected Device: Built-in DVD+RW
All data on the disc will be erased.
Exported Required Size = 11 MB
Real Export Range:
From: 2008/06/07 AM10:41:13
To: 2008/06/07 AM10:41:21
Enter: YES ESC: NO
DVR User’s Manual
36
Press ENTER to start the export; or, press ESC to abort.
If there is no any exportable device connected to the DVR unit, then a
warning message will be shown on the screen, as below figure:
No exportable device detected.
Please install the target device/media
to the DVR.
Enter: Retry ESC: Exit
4.4.3 To Export Event Video
To export event video, follow these steps:
Press SEARCH and play wanted event video. To play event video, refer to
Section Searching Recorded Video.
After entering the playback mode, press COPY. The “ezBurn” window will
display as below figure. The information shown is “read only”.
ezBurn confirmation
Selected Device: Built-in-DVD+RW
All data on the disc will be erased.
Exported Required Size = 11 MB
Export Event Info:
Data
Time
Ch
Type
2008/06/07
AM10:42:35
13
Motion
Enter: YES ESC: NO
If there is no any exportable device connected to the DVR unit, a warning
message will be shown on the screen
Press ENTER to start the export the whole event video to the connected
device; or, press ESC to abort.
4.5 Dome Control
The DVR allows users to control a dome camera by the front panel.
In Live mode, users can press CHANNEL key to display the desired dome
camera in full screen. To enter Dome Control mode, press the DOME key and
press channel key 2 to display the hint screen. To exit the Dome Control
mode and return to live mode, press ESC or DOME.
To configure the dome controls settings, see the following sections.
DVR User’s Manual
37
Formatted: Font: (Default) Arial, Font
color: Black
Formatted: Normal, Justified, Indent: Left
6 ch, No bullets or numbering, Tab stops:
Not at 1.5"
Formatted: Font color: Black
DVR User’s Manual
38
4.5.1 Dome Connection
Follow the steps to install dome camera.
See Setup Guide for RS-485 port pin definition.
Connect the R+, R- terminals on the dome camera to the D+, D- terminals
on the RS-485 port by RS-485 cable respectively. Refer to the connection
figure illustrated in Setup Guide.
4.5.2 Dome Protocol Setup
The Dome Protocol item lists the available dome protocols for communicating
with dome cameras connected to the DVR. From the Main menu, select
<Camera Setup> and press ENTER. The following menu is displayed.
Analog Camera
1. Analog Camera Select
2. Dome Protocol
3. Dome ID
4. Camera Title
5. Covert
6. Brightness
7. Contrast
8. Saturation
9. Hue
10. Audio Association
CH1
None
0
No
0
0
0
0
Yes
To configure dome protocol, select a camera first and set the communications
protocol associated with dome camera using the Direction keys and ENTER.
NOTE: The settings become effective after saving the
changes and exiting from the menu.
4.5.3 RS485 Setup
The DVR controls the domes via RS-485 communication protocol. The
RS-485 parameters in the DVR must be set to the same parameters set in
dome camera.
Users are allowed to change the RS-485 settings of the DVR. Select
<System Setup> in Main menu, then select <RS485 Setup> from the System
Setup menu and press ENTER. The following menu is displayed.
RS485 Setup
DVR User’s Manual
39
1 Unit ID
2 Baud Rate
3 Bits
4 Stop
5 Parity
224
9600
8
1
None
The ID number must match the ID address set by the dome. The Unit ID is in
the range of 1 to 255. Note that there cannot be any two devices on the same
bus given the same ID address, or a conflict may occur.
NOTE: The settings become effective after saving the
changes and exiting from the menu.
4.5.4 Dome Controlling Keys
The functions of some keys in dome control mode are totally different from
normal status function. Please refer to Setup Guide for the graphical
illustration of functional keys.
Set / Go Preset
This key is used to enter the Dome Preset menu to set up certain position as
a preset and go to the predetermined preset positions for viewing.
Toggle Hint Screen
This function is used to avoid viewing the dome parameter information while
controlling dome camera. Press this key to hide the screen. Press it again to
redisplay the screen.
Iris Open
Use to open the Iris on the dome camera.
Focus Near
Use to focus the dome camera near.
Zoom In
Use to zoom in the dome camera. This function enables users to enlarge a
certain area.
ESC
Use to leave dome control mode and return to live and full-screen viewing
mode.
DVR User’s Manual
40
Auto / Enter
In OSD setup menu interface, the key is used to make selection.
In dome control mode, this key is used to activate automatic focus and iris
function.
Iris Close
Use to close the Iris on the dome camera.
Focus Far
Use to focus the selected dome camera far.
Zoom Out
Use to zoom out the dome camera. This function enables users to shrink the
current image and view a larger area.
Pan / Tilt
Use to pan and tilt dome camera.
4.5.5 Setting Preset Points
The DVR allows users to set preset positions. The amount of preset points
depends on the dome manufacturer.
Follow the steps to set preset points.
Press a Channel key to view the corresponding camera in full screen.
Then press DOME to enter dome control mode. A Hint Screen shown as
below figure displays on the screen.
Press 2 to hide the dome control Hint Screen; press 2 again to toggle the
Hint Screen.
Use Direction keys to position the dome camera to desired position.
Hint Screen
DOME / ESC: Exit
MODE / PLAY: Iris Open / Close
SEQ / FREEZE: Focus Near / Far
MENU / SEARCH: Zoom In / Out
ENTER: Auto Focus / Iris
◄▲▼►: Pan / Tilt
CH1: Set / Go Preset
CH2: Hint Screen On / Off
Dome Control
DVR User’s Manual
41
Press 1 to access the Set/Go Preset function. The Dome Preset menu is
displayed.
Dome Preset
First Page
Index
1
2
3
4
5
6
7
Set Preset
No
No
No
No
No
No
No
Go Preset
No
No
No
No
No
No
No
Use UP / DOWN keys to select the desired preset number from the menu.
Set the <Set Preset> of the selected preset number to <Yes>, and press
ENTER to save the position. Now the preset is set and ready to be called.
4.5.6 Calling Preset Points
Follow the steps to call preset points.
Press a Channel key to view the corresponding camera in full screen.
Then press DOME to enter dome control mode. Then a Hint Screen,
shown as blow figure, will display on the screen.
Press 2 to hide the dome control Hint Screen; press 2 again to toggle the
Hint Screen.
Press 1 to access the Set/Go Preset function.
Dome Preset
First Page
Index
1
2
3
4
5
6
7
Set Preset
No
No
No
No
No
No
No
Go Preset
No
No
No
No
No
No
No
Use UP / DOWN keys to select the desired preset number from the menu.
Set the <Go Preset> of the selected preset number to <Yes>, and press
ENTER to call the preset point.
Now the selected dome camera rotates to the preset position automatically.
DVR User’s Manual
42
5. Remote Monitoring Software
The remote monitoring software is a remote browser-based software
application designed to operate with the DVR products. Using the software,
users are allowed to view live and recorded video, and configure the DVRs
remotely via a LAN, WAN or Internet on a personal computer.
The connected PC will automatically download the remote monitoring
software plug-ins from the DVR when the DVR is connected by entering its IP
address in the address bar on the browser.
Due to the setting items are similar to those listed in the DVR’s OSD setup
menu, please refer to the sections above for setting configuration of the
remote monitoring software.
The tasks can be performed with the remote monitoring software are listed
below:
Remote viewing of live/ recorded video
Remote setup of the DVR
Remote control of dome cameras
Alarm notification from the DVR
Up to three connections to one DVR using the remote monitoring software,
including one Administrator and two User operators
5.1 Remote Monitoring System Requirements
Items
Requirements
Personal Computer
Minimum:
Intel(R)® Pentium(R)® 4 CPU 3.20GHz (2 CPUs)
RAM 1 GB
Recommended:
Intel® Core™(TM)2 Quad CPU Q6600 @ 2.4GHZ
RAM 2 GB
Hard Disk Drive
20 MB available for software installation
Operating System
Windows XP, Windows Vista
Web Browser
Microsoft Internet Explorer version 6.0 or above
Monitor Resolution
Minimum 1024 x 768 with 16-bit color
Video Card
NVIDIA GeForce 8400 GS 512MB
Network Card
10Base-T (10 Mbps) or 100Base-TX (100 Mbps)
operation; must match the network configuration
Formatted: Indent: Left: 6 ch, Bulleted +
Level: 1 + Aligned at: 0" + Tab after:
0.29" + Indent at: 0.24"
DVR User’s Manual
43
5.2 Getting Start of Installation
Refer to the following description to install the Central monitoring software.
5.2.1 Changing Internet Settings
The PC operating with the remote monitoring software should be set to
accept ActiveX plug-ins. Please follow the steps to set the Internet security
settings appropriately.
Before operating the remote monitoring software, please check the IP
address of the DVR. To check the IP address, press MENU key on the unit
and enter password to access OSD setup menu. Select <System Setup>,
<Network Setup>, then <LAN Setup> to check the IP.
Start the IE; it can be started either by clicking on the desktop icon, or by
using the Start menu to access it.
NOTE: Windows IE provides the ActiveX component that is
required when using the remote monitoring software.
Select <Tools> from the main menu of the browser, then <Internet
Options>, and then click the <Security> tab.
Select <Trusted sites> and click <Sites> to specify its security setting.
Formatted: Indent: Left: 6 ch, Bulleted +
Level: 1 + Aligned at: 0" + Tab after:
0.29" + Indent at: 0.24"
Formatted: Indent: Left: 6 ch, Bulleted +
Level: 1 + Aligned at: 0" + Tab after:
0.29" + Indent at: 0.24"
Formatted: Indent: Left: 6 ch, Bulleted +
Level: 1 + Aligned at: 0" + Tab after:
0.29" + Indent at: 0.24"
DVR User’s Manual
44
Uncheck “Require server verification (https:) for all sites in this zone”.
Type the IP address of the unit in field and click <Add> to add this web site
to the zone.
Click <OK> to confirm the setting and close Trusted sites dialog.
In the Security Level area, click <Custom Level>. The Security Settings
screen is displayed.
Under <ActiveX controls and plug-ins>, set all items to <Enable> or
<Prompt>.
Click <OK> to apply the setting and close the <Security Settings> screen.
Click <OK> to close Internet Options dialog.
Now the installation can continue to the next step.
Formatted: Indent: Left: 6 ch, Bulleted +
Level: 1 + Aligned at: 0" + Tab after:
0.29" + Indent at: 0.24"
Formatted: Indent: Left: 6 ch, Bulleted +
Level: 1 + Aligned at: 0" + Tab after:
0.29" + Indent at: 0.24"
DVR User’s Manual
45
5.2.2 Installing Remote Monitoring Software
Start the browser to initiate the installation of the remote monitoring software
on the PC. The IP address of the DVR can be saved as a Favorites item in
the web browser to enable easy access in the future.
Start the IE; it can be started either by clicking on the desktop icon, or by
using the Start menu to access it.
Enter the IP address of the DVR in the address bar at the top of the
browser.
The ActiveX controls and plug-ins dialog will show twice for confirmation;
click <Yes> to accept ActiveX plug-ins. The remote monitoring software
plug-ins will be downloaded and installed on the PC automatically when
the connection is successfully made.
NOTE: Do not enter any leading “0” characters
in the address, for example, “192.068.080.006” should be entered
as “192.68.80.6”. If the default trigger port 80 is changed into
another one, take port 81 for example, the IP address should be
entered as “192.68.80.6:81”.
A version check starts to verify whether the remote monitoring software
was installed already, and also check if the version is the same as that
stored in that particular DVR. This process may take up to 30 seconds.
When the software is completely downloaded and installed, the Login
Screen is now displayed.
Formatted: Indent: Left: 6 ch, Bulleted +
Level: 1 + Aligned at: 0" + Tab after:
0.29" + Indent at: 0.24"
Formatted: Indent: Left: 6 ch, Bulleted +
Level: 1 + Aligned at: 0" + Tab after:
0.29" + Indent at: 0.24"
DVR User’s Manual
46
5.2.2.1 Login / Logout
Login using either <Admin> or <User> account. <Admin> account can modify
configuration without restraint, while <User> account is limited to general
remote access of the unit.
One “Admin” and up to two “Users” can access a DVR at the same time.
Nevertheless, if the “Admin” account is currently accessing the unit’s OSD
setup menu at the DVR site, then the “Admin” account at the remote
monitoring site cannot change the settings at the same time. The Admin
account of the DVR has priority.
The following steps demonstrate procedures to view video from remote unit:
Start the remote monitoring software by entering the IP Address of the
DVR in the Address bar of the browser. Alternatively, click on the Favorite
entry for the unit (if the IP address of the unit has been set).
Enter the Username and password. The login username and password
can be saved to ease future login. The default usernames and passwords
are listed as below.
Login Type
Default Username
Admin
User
Default Password
1234
4321
Click <OK> to login to the DVR. The process may take a few seconds.
If the connection is made successfully, the main window will display live
video of the attached cameras.
If the IE browser is closed, the remote system is logout and disconnected
from the DVR at the same time.
Formatted: Indent: Left: 6 ch, Bulleted +
Level: 1 + Aligned at: 0" + Tab after:
0.29" + Indent at: 0.24"
Formatted: Indent: Left: 6 ch, Bulleted +
Level: 1 + Aligned at: 0" + Tab after:
0.29" + Indent at: 0.24"
DVR User’s Manual
47
5.2.2.2 Software Upgrades
If a new version of the remote monitoring software is available on the DVR,
upgrade will be prompted while accessing the unit. Follow the steps to
upgrade the software.
The message as the above figure will be prompted. Click <Yes> to accept
version upgrade.
Start the IE again and enter the IP address of the DVR in the Address bar
of the browser; or if the unit address is set as a Favorite site, click the
Favorites entry for the unit.
When the software is completely downloaded and installed, the Login
Screen will be displayed.
5.3 Basic Operation for Monitoring Remotely
When a DVR is successfully connected, the main window of the Central
monitoring software will display as shown below. The connected cameras of
the DVR will be listed on the left and an array of camera output windows will
display on the right of the main window.
Formatted: Indent: Left: 6 ch, Bulleted +
Level: 1 + Aligned at: 0" + Tab after:
0.29" + Indent at: 0.24"
Formatted: Indent: Left: 6 ch, Bulleted +
Level: 1 + Aligned at: 0" + Tab after:
0.29" + Indent at: 0.24"
Formatted: Font: (Default) Arial
DVR User’s Manual
48
Refer to the following table for brief description of functional items:
Item
Description
Item
Description
1
Instant Recording
9
Capture Snapshot
2
Audio On/Off
10
4:3 Viewing Aspect
3
Select Camera
11
HDD Status
4
Display Mode
12
Playback Control
5
View Live Camera
13
Select Picture Size
6
Playback Video
14
Select Bandwidth Speed
7
Setup Menu
15
Download DVRPlayer
8
Search Event List
The functions on the remote monitoring software will be described in the
following sections.
5.3.1 To View Live Video
View live video from the cameras attached to the DVR by clicking <Live>
button on the main window toolbar.
Choose desired display mode – full-screen, 2x2 windows, 3x3 windows, and
4x4 windows – after the live images of the DVR are displayed on the main
window. When a dome camera is connected and viewed in single channel
full-screen mode, the dome camera control operation can be accessed. To
choose desired display mode and to operate dome camera control, refer to
the following sections.
5.3.1.1 Selecting Display Mode
Choose the number of windows to be displayed on the
main window. Click one of the display buttons in MODE
section. Available selections are 4, 9 and 16 camera
displays. To view certain window in full screen, either
double-click on the wanted window, or click on the
corresponding CAMERA button.
Formatted: Left 0 ch
Formatted: Font: (Default) Arial
DVR User’s Manual
49
5.3.1.2 Operating Cameras with Dome Control
The remote monitoring software allows users to control and
configure a dome camera remotely.
Click on any CAMERA button displayed with a dome icon to
view the camera in full screen. The Dome Control Panel will
be displayed on the main window. The items on the dome
control panel are described as follows.
Set Preset
Set Preset is used to set up preset positions. The remote monitoring software
allows its user to set up to 255 preset positions with American Dynamics,
Fastrax, JVC, Panasonic (C & N), and Pelco (Pelco P & Pelco D) domes.
Use Direction buttons to move dome camera to an appropriate position, and
then click the button and choose wanted number from the pull-down list. The
preset position is named as the selected number.
Go Preset (•)
Go Preset is used to call the camera preset point, which was set up with the
set preset point function. Click and choose a number to call the preset point
for viewing.
Auto Focus (A.F.)
Click on it and the focus of the camera will be automatically adjusted to show
a clearer image.
Dome ID (ID).
Click for changing the dome ID and protocol.
User’s privilege is not allowed to change the
dome ID and protocol; Admin privilege is
required to access this function.
Focus +/−
Use to adjust the camera lens to focus on objects for a clear view. Click on
<Focus +> to focus near or <Focus −> to focus far.
Iris +/−
DVR User’s Manual
50
This item is used to open and close the iris to let more or less light into the
camera. Click on <Iris +> to open iris or <Iris −> to close iris.
Zoom +/−
Users are allowed to zoom-in or zoom-out using the adjusting buttons.
Zoom-in to enlarge a certain area and zoom-out to view more area.
Direction Button
This button is used to pan and/or tilt the dome camera. Click the arrows in the
directions to be viewed.
5.3.2 Instant Recording
The Instant Recording function allows users to record video quickly to the
PC.
NOTE: The Audio function is set to OFF as the
default setting.
The Instant Recording function allows users to record
video quickly to the PC.
NOTE: The Audio function is set to OFF as the
default setting.
5.3.2.1 Recording Video Instantly
Follow the steps to start recording instantly:
Click on the <Instant Recording> button.
Select the destination folder to save the video.
Click on the button again to stop recording.
NOTE: The instant recording video will be saved as
*.drv file.
5.3.2.2 To Playback Instant Recorded Video
Follow the steps to playback a video recorded by “Instant Recording”.
Click <Play> on main window toolbar and click <Local Playback> tab.
Formatted: Normal, Tab stops: Not at 1"
Formatted: Font: (Default) Times New
Roman, 12 pt, Not Bold, Font color: Auto
Formatted: Font: 12 pt, Not Bold, Font
color: Black
Formatted: Indent: Left: 6 ch, Bulleted +
Level: 1 + Aligned at: 0" + Tab after:
0.29" + Indent at: 0.24"
Formatted: Indent: Left: 6 ch, Bulleted +
Level: 1 + Aligned at: 0" + Tab after:
0.29" + Indent at: 0.24", Tab stops: Not at
0.29"
Formatted: Indent: Left: 6 ch, Bulleted +
Level: 1 + Aligned at: 0" + Tab after:
0.29" + Indent at: 0.24"
DVR User’s Manual
51
Click <Open> to choose a recorded file.
Click <OK> to start playing the recorded video.
5.3.3 To Playback Video
The remote monitoring software allows users to view recorded video either
from the DVR, or from the hard disk drive of the PC
To access the Playback screen, click <Play> button on the main window
toolbar. There are three tabs in the Playback screen: <Remote Playback>
and <Local Playback> tabs. <Remote Playback> allows users to play back
from the DVR. <Local Playback> enables users to playback a recorded video
file stored on the hard disk drive of the PC.
The DVR continues recording while playing back recorded video on the PC,
either remote playback or local playback.
5.3.3.1 Playing Back Remote Video
To view remote video, click <Play> on the main window toolbar, and then
<Remote Playback> tab. The <Remote Playback> screen will be displayed.
The <From> and <To> in the <Available Record Video> displays the date and
time from which recorded video is available for playback.
To playback remote video segments, follow these steps:
Choose <Playback> in <Select> field for playback recorded video.
In <Start> field, users can change the date and time either by typing
Formatted: Font: (Default) Arial
Formatted: Indent: Left: 6 ch, Bulleted +
Level: 1 + Aligned at: 0" + Tab after:
0.29" + Indent at: 0.24"
DVR User’s Manual
52
desired numbers directly or using the arrow buttons.
To type directly:
Click on day, month and year of date field respectively, and type the
desired numbers directly. Follow above steps to adjust the hour, minute
and second of time field.
To use the arrow buttons:
Click on the arrow button next to the date field to display the calendar; then
click the left and right arrow at the top of the calendar to change the date.
Use up and down arrow next to the time field to change to the wanted time.
The other way to select date and time is by moving the blue sliding bar.
Click <OK> to start the playback, or click <Close> to abort.
The other option <Download (.DRV)> in <Select> field enables users to
download the video segment of selected date and time to the PC. The
selection of time duration is the same as described above. Files
downloaded will be in *.drv format.
5.3.3.2 To Playback Local *.drv Files
The <Local Playback> tab allows users to playback *.drv video files stored in
the PC's hard drive.
Formatted: Indent: Left: 6 ch, Bulleted +
Level: 1 + Aligned at: 0" + Tab after:
0.29" + Indent at: 0.24"
Formatted: Justified
DVR User’s Manual
53
Follow below steps to play back a downloaded *.drv file with the remote
monitoring software.
Click <Open> and the file selection screen is displayed.
Select the *.drv video file to playback and click <OK>.
Click <OK> in the <Local Playback> Screen to start the playback, or click
<Cancel> to abort.
View the video playback using the Playback controls.
To end the playback, click <Live> to return to live video.
5.3.3.3 Playback Controls
When the local or remote video is being played, the remote monitoring
software is in Playback Mode. The playback controls toolbar will emerge on
the main window toolbar.The Playback controls and indicators are described
as below.
Icon
Name
Description
⊲⊲
Fast Backawad /
Step Backward
1. Click to play the recorded video in backward
direction. Click repeatedly to select the backward
playback speed: 1×, 2×, 4×, 8×, 16×, or 32×.
2. When playback is paused, click repeatedly to
move backward step-by-step.
⊳ / ⌷⌷
Play / Pause
1. While playing, click to pause the playback.
2. When paused, click to resume the playback.
⊳⊳
Fast Forward /
Step Forward
1. Click to play the recorded video in forward
direction. Click repeatedly to select the forward
playback speed: 1×, 2×, 4×, 8×, 16×, or 32×.
2. When playback is paused, click repeatedly to
move forward step-by-step.
Formatted: Indent: Left: 6 ch, Bulleted +
Level: 1 + Aligned at: 0" + Tab after:
0.29" + Indent at: 0.24"
Formatted: Left
DVR User’s Manual
54
5.3.4 Search from Event List
Click SEARCH, the Event List appears. The List contains information about
the alarm events that the unit recorded and saved. Up to 1024 events can be
listed in the Event List.
The Event List displays each event by its number, the date and time of the
event, the type of the event (including Alarm In, Motion Detection, Video Loss,
and Over Speed), and the camera channel where the event occurred.
To view an event video, follow these steps:
Click SEARCH button positioned in the main window toolbar. The Event
List appears.
Scroll through the Event List and highlight the interested events.
Double-click on the desired event to view the event video.
Formatted: Font: (Default) Arial
Formatted: Indent: Left: 6 ch, Bulleted +
Level: 1 + Aligned at: 0.61" + Tab after:
0.9" + Indent at: 0.85"
DVR User’s Manual
55
5.3.5 Take a Snapshot
Snapshot is a simple screen capture tool. When users click on the
SNAPSHOT button, it will capture the screenshot of the window that is
currently showing on the screen. Each click captures one screenshot to be
saved as a JPEG file on the desktop. The snapshot file will be named as
“Snapshot-*”.
5.3.6 Health Status of HDD
This function verifies the HDD status of the DVR. The following figure is an
example.
The information items shown in the chart are described as below:
Device Name
This item shows the model name of the HDD.
Int./Ext.
This item indicates whether the HDD is an internal or external device.
Total Size
This item indicates the total size of the HDD.
State
This item indicates whether the HDD is active or non-active.
Temperature
This item indicates the current temperature of the HDD in Celsius degree.
DVR User’s Manual
56
5.3.7 Remote Monitoring Software Trouble Shooting Guide
What happened if the server requests to upgrade the software every time the
DVR is connected? If the following screen displays repeatedly, please follow
the steps to delete the temporary internet files.
- Select <Tools> from the main menu of the web browser, then <Internet
Options>, and then click the <General> tab.
- Click the <Delete Files> button in the <Temporary Internet Files> field; the
<Delete Files> screen displays as below.
- Check the <Delete all offline content> box and click <OK>.
Now, enter the IP address of the DVR to make the connection again.
Formatted: Indent: Left: 1.01", No bullets
or numbering
Formatted: Indent: Left: 1.01", Bulleted +
Level: 1 + Aligned at: 0" + Tab after:
0.29" + Indent at: 0.24", Tab stops: Not at
0.29"
Formatted: Indent: Left: 1.01", Bulleted +
Level: 1 + Aligned at: 0" + Tab after:
0.29" + Indent at: 0.24", Tab stops: Not at
0.29"
Formatted: Indent: Left: 6 ch, Bulleted +
Level: 1 + Aligned at: 0.61" + Tab after:
0.9" + Indent at: 0.85"
DVR User’s Manual
57
Appendix A: Technical Specifications
All specifications are subject to change without notice.
Specifications
4ch Model
8ch Model
16ch Model
Video
Operation System
Embedded ( Linux )
Input
BNC×4, 1.0Vp-p, 75 ohm
BNC×8, 1.0Vp-p, 75 ohm
BNC×16, 1.0Vp-p, 75
ohm
UTP (Optional)
4ch UTP
8ch UTP
16ch UTP
Input IP devices
Up to 2ch
Up to 4ch
Outputs
Main Monitor
BNC × 1, 1.0Vp-p, 75 ohm
Call Monitor
BNC × 1, 1.0Vp-p, 75 ohm
VGA Output (Optional)
800 × 600, 1024 × 768, 1280 × 1024 pixels@60 Hz (Optional)
Picture Refresh Rate
NTSC: 30 PPS/Per channel, PAL: 25 PPS/Per channel
Audio
Input
Terminal Block, ×4 Line-in
Terminal Block, ×8 Line-in
Terminal Block, ×16 Line-in
UTP
Supported
Output
Main out
RCA × 1, 1 Channel Line-Out
Call Audio
RCA × 1, 1 Channel Line-Out
Compression Method
Proprietary
Data Rate
8 KB/s per channel
Recording
Compression Method
H.264 / MJPEG
Recording Mode
Schedule, Alarm, Motion Detection
Pre-Alarm
Yes
Recording
Resolution
& Rate
NTSC 720 × 480
720 × 240
360 × 240
Max 30 fps
Max 60 fps
Max 120 fps
Max 60 fps
Max 120 fps
Max 240 fps
PAL 720 × 576
720 × 288
360 × 288
Max 25 fps
Max 50 fps
Max 100 fps
Max 50 fps
Max 100 fps
Max 200 fps
Recording Mode
8 Levels Presets, Adjustable
Image Size
1KB to 20KB/Picture
Storage Mode
Linear / Circular
Data Life Time
Yes (Programmable)
Storage
Build-in Storage Interface
×3, SATA
Cartridge / DVD+RW
Optional
Export Storage
×3 USB 2.0 Ports, Support ThumbDrive® or DVD+RW
Alarm
Alarm Input
×4, Terminal Block
×8, Terminal Block
×16, Terminal Block
Alarm Relay Output
x1, Terminal Block
Alarm Detection
N.C./N.O., Programmable
Motion Detection
16 × 12 Grid Array, Sensitivity, Trigger Level Adjustable
Video Loss Detection
Programmable
Communication
Network Connectivity
Ethernet RJ-45 Connector, 10/100 Mbps
Compatible IP Camera
SONY, AXIS, ACTi, Vivotek,
Remote Control Software
Central Management System (CMS), Remote Software
Remote Operation
Monitor, Playback, Recording, System Setup, Dome Camera Control, Archive
RS-485
Terminal Block
Dome Control Protocol
Pelco P, Pelco D, AD422, Fastrax 2, Panasonic
Formatted: Justified
Formatted Table
Formatted Table
Formatted Table
Formatted: Font: 10 pt
Formatted: Font: 10 pt
Formatted: Font: 10 pt
Formatted: Font: 10 pt
Formatted: Font: 10 pt
Formatted: Font: 10 pt
Formatted: Font: 10 pt
Formatted: Font: 10 pt
Formatted: Font: 10 pt
Formatted: Font: 10 pt
Formatted Table
DVR User’s Manual
58
General
Unit Dimension (W×H×D)
362 × 90 × 350 mm (14.2 × 3.5 × 13.7 inches)
Unit Weight
5.5 Kg (12.1 lbs)
Package Dimension (W×H×D)
410 × 210 × 500 mm (16.1 × 8.2 × 19.6 inches)
Package Weight
7 Kg (15.4 lbs)
Operation Temperature
-5°C ~ 40°C (23 °F ~ 104 °F))
Relative Humidity
10% ~ 90% Non-condensing
Power Consumption & Input
AC 100〜240V, 50-60 Hz, 60W Adaptor
Appendix B: Connect UTP Camera
UTP, short for Unshielded Twisted Pair, is a popular type of cables that is one of the most
common medium in telecommunication industry. Installing the UTP module allows the DVR
to supply power to and transmit images from any four distinctive UTP cameras through the
UTP cables (CAT5). This leads to an economical and fast installation of surveillance. Some
benefits are described as below:
1.- Cost Down on Wiring – The cost of wiring decreases for more than 60%
1.- Save Time & Space – Easy to install and it takes less space than coaxial cable.
2.- Cost Down on Camera Power Adapter – There is no need to buy adapter for each
UTP Color Box Camera because the power is directly supplied from the DVR unit.
The Optiview H.264 DVR provides the option to connect UTP cameras. Follow the steps
below to complete the UTP camera installation.
Step 1:
Connect the DVR and the UTP Camera via the UTP cable (CAT5).
NOTE: The DVR should be powered OFF before the installation of the
UTP Camera.
Step 2:
On the back panel of the DVR, switch the video source to ON (UTP). For instance, if a UTP
Camera will be installed to channel 1, switch the video source 1 to ON. The correct setting
is shown as below.
Formatted Table
Formatted: Indent: Left: 0", First line: 0",
Bulleted + Level: 1 + Aligned at: 0" + Tab
after: 0.33" + Indent at: 0.33", Tab stops:
Not at 0.5"
DVR User’s Manual
59
Video Source Selection
Follow the same procedure if more UTP Cameras to CH2, CH3, or CH4 will be installed.
NOTE: Do NOT insert both BNC and UTP video sources to the same
channel simultaneously, or the video will not function correctly and it may cause
the video to look like the figure below. For instance, if a UTP Camera is already
installed to channel 1, do not install another camera to the BNC port of channel 1.
Bad Video Output
Step 3:
Plug in the power adapter to the DVR, and the DVR will start to boot. The installation is
complete.
NOTE: The UTP Board provides power up to 5.5W. If the power consumption of
the camera is more than 5.5W, the UTP Board will start beeping.
NOTE: The length of each UTP cable should NOT exceed 300 meters (or 984 feet), or
it may cause loss or weakening of signal. The following table shows performance at
different distances.
Distance
Meters / Feet
UTP-Converter
Power Output (W)
Video Quality
0
5.526
Excellent
100 / 328
5.256
Excellent
200 / 656
5.04
Good
300 / 984
4.77
Good
DVR User’s Manual
60
Appendix C: Connect Analog Camera via UTP
Converter
NOTE: The UTP Converter can provide power up to 5.5W. If the power
consumption of the camera is higher than 5.5W, do NOT connect it to the
UTP Converter.
Introduction:
The UTP converter is made especially for users who want to
build a connection between an UTP DVR and a traditional
analog camera, which allows the transmission of power and
video signal through one CAT5 cable.
The UTP converter has two cables at one end: one cable for
connecting with the camera’s BNC video connector; the
other for connecting with power jack of the camera.
A RJ-45 connector is positioned at the other end of the
converter. Connect the UTP converter and the UTP DVR
using a CAT5 cable.
Installation:
To build up an UTP connection using the UTP converter,
connect the BNC and power connectors to camera
respectively, and connect with the DVR using an Ethernet
CAT5 cable.
DVR User’s Manual
61
Appendix D: Recommended HDDs
Refer to the following list for some recommended HDDs to be used in the DVR.
Brand
Model Name
Model Number
Size
Seagate
Barracuda ES.2
ST3500320NS
500G
Barracuda 7200.11
ST3500320AS
500G
Barracuda 7200.11
ST3750330AS
750G
Barracuda 7200.11
ST31000340AS
1000G
HITACHI
DeskStar
HDP725032GLA360
320G
DeskStar
HDP725050GLA360
500G
Maxtor
DiamondMax 22
STM3500320AS
500G
Western Digital
WD AV
WD1600AVJS
160G
WD AV
WD2500AVJS
250G
WD AV
WD3200AVJS
320G
WD AV
WD5000AVJS
500G
WD AV
WD7500AVVS
750G
DVR User’s Manual
62
Appendix E: Remote Controller
The operational function keys (on the left) and dome camera control keys (on the right) on
the remote control are listed as below figure:
Formatted: Font: (Default) Arial
DVR User’s Manual
63
DVR User’s Manual
64
The keys of the remote control function as the keys of the front panel of the DVR. The only
difference between the remote control and the front panel keys is the “DVR SEL” key. The
DVR Selection key is used to switch control between each DVR.
The remote control can be used to control up to 16 DVRs. To setup the remote control, the
first thing is to assign a unique DVR Unit ID to each DVR.
Use the front panel of the DVR, and follow this path to change the DVR Unit ID, <Main
Menu> <System Setup> <RS485 Setup> <Unit ID>. Change the DVR Unit ID to
any number between 224 and 239, and exit the menu.
The ID Table is listed below for reference.
DVR Unit ID
224
225
226
227
228
229
230
231
Remote Control #
1
2
3
4
5
6
7
8
DVR Unit ID
232
233
234
235
236
237
238
239
Remote Control #
9
10
11
12
13
14
15
16
After the DVR Unit ID is changed, setup the “DVR SEL” of the remote control. Press “DVR
SEL”, and then press the Remote Control # immediately to select the DVR. For example,
assuming the DVR Unit ID is set to 225, press “DVR SEL” and then press “2” immediately.
Now, the remote control will only be able to control the specified DVR. Press “DVR SEL”,
and then press the Remote control # to switch between DVRs.
To exit the single DVR control mode, press “DVR SEL”, and then press “ESC” to do so.
DVR User’s Manual
65
Appendix F: Setting up a DVR behind a Router
This appendix describes how to set up a router if the DVR connects to the internet via a
router.
To properly operate a web server, e.g. a DVR, users have to set up both the IP and port of
the DVR, which are essential for data and command transmission. The port setting is
adjustable in OSD setup menu of the DVR and only one port is needed to do remote
operation. Typically and by the default, the DVR operates on port 80, which is well known
as the http port. Please make sure that port 80 is not blocked by the ISP. Otherwise, a
different available port shall be reset and the setting of the DVR shall be changed.
In case a router or sometimes a DSL modem is in place, the real IP is now assigned to the
router instead of the DVR. The DVR is located behind the wall (router) and operates on
virtual IP. In most cases, virtual IP starts with 192.168.x.x. The router has two IP: one is real
IP (WAN IP); the other is virtual IP (LAN IP). The virtual IP would be 192.168.x.1. When the
remote users want to operate the DVR, they will have to send command to the real IP, i.e.
the router. Then the router has to map (forward) the command to the DVR. Thus, it is
required to set up the router for port mapping (forwarding) before images from the DVR can
be remotely viewed on a PC.
See the router manufacturer's websites for more instructions on port mapping.
DVR User’s Manual
66
Following is an example of how the router should be set.
Router
(D-Link DI-724P+)
WAN IP: 218.160.54.13
LAN IP: 192.168.0.1
PC
IP: 192.168.0.100
DVR 1
IP: 192.168.0.167
Trigger port: 80
DVR 2
IP: 192.168.0.200
Trigger port: 81
To change the setting of the router, a PC with web browser is required.
Connect to D-Link DI-724P+ from PC via IE. The setup screen will be shown after entering
the correct username and password.
Click the <Advanced> tab and follow the steps to set up web port forward to DVR 1.
DVR User’s Manual
67
Select <Enabled> to set up the service.
Enter the name of the setting in the Name field: DVR 1.
Enter Private IP: 167
Choose <TCP> as the Protocol Type.
Enter Private Port: 80.
Enter Public Port: 80.
Click <Always> for the Schedule setting.
Click <Apply>.
Click <Continue> to go on when the following screen displays.
Follow the steps to set up web port forward to DVR 2.
Click <Enabled> to set up the service.
Enter the name of the setting in the Name field: DVR 2.
Enter Private IP: 200
Choose <TCP> as the Protocol Type.
Enter Private Port: 81.
Enter Public Port: 81.
Click <Always> for the Schedule setting.
Click <Apply>.
Now DVR 1 can be connected via http://218.160.54.13:80 and DVR 2 can be
connected via http://218.160.54.13:81.
If there are more than one DVR behind the router, repeat the steps for port mapping
setting.

Navigation menu