The Worm Electro Harmonix Freeze Instructions
Electro-Harmonix Freeze Instructions freeze Electro-Harmonix - Freeze - Instructions
User Manual: Electro-Harmonix Freeze Instructions Electro-Harmonix - Freeze - Instructions
Open the PDF directly: View PDF
.
Page Count: 1
| Download | |
| Open PDF In Browser | View PDF |
SLOW – When the footswitch is triggered, the FREEZE will sustain the current input, fading in the effect. The sound will be sustained until the footswitch is released, at which point the effect will fade out slowly. The speed of the fade can be set during slow-speed initialization. See below. FREEZE Infinite Sound Retainer Congratulations on your purchase of the Electro-Harmonix FREEZE pedal! At the simple push of a button, the FREEZE will allow you to sustain individual notes and chords indefinitely. With three different modes of operation, it’s easy to set up just the right type of sound retention for the club, the studio or your bedroom. WARNING: Your Freeze pedal comes equipped with an Electro-Harmonix 9.6DC-200BI power supply (same as used by Boss™ & Ibanez™: 9.6 Volts DC 200mA). The Freeze requires 140mA at 9VDC with a plug that is center negative. The Freeze does not take batteries. Using the wrong adapter may damage your unit and void the warranty. LATCH – When the footswitch is triggered, the FREEZE will immediately sustain your current sound. The sound will continue to be sustained upon releasing the footswitch. When the footswitch is triggered again, the FREEZE will immediately replace the sustained sound with the new current input. A double-tap on the footswitch will silence the effect. – SLOW-SPEED INITILAZATION – The speed at which the effect fades in/out in SLOW mode can be adjusted by following these steps: 1) Unplug the power jack 2) Hold down the footswitch 3) While holding down the footswitch, plug in the power jack (LED will blink) 4) Move the mode switch to the preferred setting based on this table: Switch Position Up Middle Down – CONTROLS – EFFECT LEVEL – Controls the volume of the sustained sound. The output always contains the dry signal at its original volume MODE SWITCH – Selects between one of three effect modes: FAST, SLOW, and LATCH. See the MODE DESCRIPTIONS section for more detail. STATUS LED – The LED is on while the effect is sounding or fading out. When the LED is off, the effect is completely silenced and the output contains only the pure dry signal. INPUT JACK – Connect the output of your instrument or another effects pedal to this jack. The input impedance presented at the INPUT jack is 2.2 M. AMP JACK – Connect the AMP jack to your amplifier input or the input of another effects pedal. The output impedance at this jack is 470. 9V Power Jack – Plug the output of the supplied AC Adapter into this jack located at the top of the FREEZE. The FREEZE’s current requirement is 140mA at 9VDC. The polarity of the power jack is center-negative. The FREEZE accepts most Boss style AC Adapters. – MODE DESCRIPTIONS – FAST – When the footswitch is triggered, the FREEZE will immediately sustain the current input. The sound will be sustained until the footswitch is released, at which point the effect will immediately disengage. 5) Fade-in Speed 200ms 200ms 800ms Fade-out Speed 400ms 1.0 sec 3.2 sec Release the footswitch, the FREEZE is ready for normal operation. The FREEZE will retain the chosen fade speed through power cycles and will not change until reinitialized.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 1 Language : en-US Tagged PDF : Yes Title : The Worm Author : John H Pisani Creator : Microsoft® Office Word 2007 Create Date : 2010:06:15 11:41:33 Modify Date : 2010:06:15 11:41:33 Producer : Microsoft® Office Word 2007EXIF Metadata provided by EXIF.tools