Removing the front panel assembly (See Fig.1) 1. Press the eject button in the lower right part of the front panel. Remove the front panel assembly from the body. Front panel assembly Eject button Fig.1 Removing the front chassis assembly (See Fig.2 and 3) Tab a Prior to performing the following procedure, remove the front panel assembly. 1. Release the four joint tabs a on both sides of the front chassis assembly and remove the front chassis assembly toward the front. Tab a Front chassis assembly Fig.2 Heat sink Tab a Tab a Fig.3 1-4 Front chassis assembly KD-S621 Removing the heat sink (See Fig.4) 1. Remove the three screws A on the left side of the body. Heat sink A A Fig.4 Removing the bottom cover (See Fig.5 and 6) Joints b Bottom cover Prior to performing the following procedure, remove the front panel assembly, the front chassis assembly and the heat sink. 1. Turn over the body and unjoint the five joints b with the bottom cover and the body using a screwdriver. Joint b Joints b Rear panel Fig.5 Joints b Bottom cover Joint b Joints b Rear panel Fig.6 1-5 KD-S621 Removing the main board (See Fig.7 and 8) Prior to performing the following procedure, remove the front panel assembly, the front chassis assembly, the heat sink and the bottom cover. C C B D D 1. Remove the screw B, the four screws C and the three screws D attaching the rear bracket on the back of the body. Remove the rear panel. Rear panel D Fig.7 2. Remove the two screws E attaching the main board on the bottom of the body. Disconnect connector CN501 on the main board in the direction of the arrow. Main board E E CN501 Removing the CD mechanism section (See Fig.9) Fig.8 CD mechanism section F F Prior to performing the following procedure, remove the front panel assembly, the front chassis assembly, the heat sink, the bottom cover and the main board. 1. Remove the three screws F attaching the cassette mechanism section on the back of the top chassis. F Fig.9 1-6 C Top chassis KD-S621 Removing the control switch board (See Fig.10 to 12) G G Prior to performing the following procedure, remove the front panel assembly. 1. Remove the four screws G attaching the rear cover on the back of the front panel assembly. 2. Unjoint the nine joints c with the front panel and the rear cover. G Rear cover G Fig.10 3. Remove the control switch board on the back of the front panel. Joints c Front panel Joints c Joints c Rear cover Joints c Fig.11 Front panel Control switch board Fig.12 1-7 KD-S621 Removing the CD mechanism control board(See Fig.1 and 2) Damper bracket CD mechanism ass’y I I f m m Unsolder the part f and g on the CD mechanism control board. h I Remove the stator fixing the CD mechanism control board and the damper bracket (To remove the stator smoothly, pick up the center part). i Remove the screw F attaching the CD mechanism control board. CD mechanism control board Front bracket Remove the CD mechanism control board in the direction of the arrow while releasing it from the two damper bracket slots i and the front bracket slot j. F g j Fig.1 Disconnect the flexible wire from connector on the pickup unit. Pickup unit Flexible wire ATTENTION: Turn the FD gear in the direction of the arrow to move the entire pickup unit to the appropriate position where the flexible wire of the CD mechanism unit can be disconnected easily (Refer to Fig.2). Shift the lock FD gear Fig.2 CD mechanism control board k k G G Loading motor Front bracket Fig.3 Pull outward Front bracket Flame 1-8 Fig.4 Pull outward KD-S621 Removing the loading motor (See Fig.3 to 5) Loading motor H Prior to performing the following procedure, remove the CD mechanism control board. Belt Remove the two springs k attaching the CD mechanism ass’y and the front bracket. Fig.5 Remove the two screws G and the front bracket while pulling the flame outward. Remove the belt and the screw H from the loading motor. CD mechanism ass’y Damper bracket I m Flame m I I Fig.6 Removing the CD mechanism ass’y (See Fig.1, 6 to 9) I Prior to performing the following procedure, remove the CD mechanism control PWB and the front bracket (loading motor). 1. Remove the three screws I and the damper bracket. Fig.7 2. Raise the both sides fix arms and move the fix plates in the direction of the arrow to place the four shafts l as shown in Fig.8 and 9. Rear damper bracket 3. Remove the CD mechanism ass’y and the two springs m attaching the flame. J Fix plate (L) Fix arm (L) 4. Remove the two screws J and both sides rear damper brackets from the dampers. Detach the CD mechanism ass’y from the left side to the right side. l l ATTENTION: The CD mechanism ass’y can be removed if only the rear damper bracket on the left side is removed. Damper Fig.8 Fix arm (R) J Rear damper bracket Fix plate(R) l Damper l Fig.9 1-9 KD-S621 Removing the feed motor ass’y (See Fig.10) Prior to performing the following procedure, remove the CD mechanism control board, the front bracket (loading motor) and the CD mechanism ass’y. FD screw Part n Feed motor ass’y Part O K 1. Remove the two screws K and the feed motor ass’y. Pickup unit FD gear Pickup unit Fig.10 Removing the pickup unit (See Fig.10 and 11) *Prior to performing the following procedure, remove the CD mechanism control board, the front bracket (loading motor), the CD mechanism ass’y and the feed motor ass’y. L Nut push spring plate Pickup mount nut 1. Detach the FD gear part of the pickup unit upward. Then remove the pickup unit while pulling out the part n of the FD screw. Pickup unit FD screw ATTENTION: When reattaching the pickuap unit, reattach the part o of the pickup unit, then the part n of the FD screw. 2. Remove the screw L attaching the nut push spring plate and the pickup mount nut from the pickup unit. Pull out the FD screw. Removing the spindle motor (See Fig.12 and 13) Fig.11 p p Prior to performing the following procedure, remove the CD mechanism control board, the front bracket (loading motor), the CD mechanism ass’y and the feed motor ass’y. 1. Turn up the CD mechanism ass’y and remove the two springs p on both sides of the clamper arms. Open the clamper arm upward. 2. Turn the turn table, and remove the two screws M and the spindle motor. Fig.12 Spindle motor M M Fig.13 1-10 KD-S621 Adjustment method Test instruments required for adjustment 1. Digital oscilloscope (100MHz) 2. AM Standard signal generator 3. FM Standard signal generator 4. Stereo modulator 5. Electric voltmeter 6. Digital tester 7. Tracking offset meter 8. Test Disc JVC :CTS-1000 9. Extension cable for check EXTGS004-26P 1 Standard volume position Balance and Bass &Treble volume : lndication"0" Loudness : OFF Frequency Band FM 87.5MHz ~ 108.0MHz MW 522kHz ~ 1620 kHz LW 144kHz ~ 279kHz Dummy load Exclusive dummy load should be used for AM,and FM. For FM dummy load,there is a loss of 6dB between SSG output and antenna input.The loss of 6dB need not be considered since direct reading of figures are applied in this working standard. Standard measuring conditions Power supply voltage DC14.4V(10.5~16V) Load impedance 4 (2 Speakers connection) Line out load impedance 20k Output Level Line out 2.0V (Vol. MAX) How to connect the extension cable for adjusting The cardboard is cut in a suitable size. uses for the insulation stand of mechanism. EXTGS004-26P 1-11 KD-S621 Flow of functional operation until TOC read • When the pickup correctly moves to the inner area of the disc Microprocessor commands Power ON Set Function to CD • When the laser diode correctly emits Microprocessor commands Disc inserted FMO TC9462 "53" Pickup feed to the inner area FEED MOTOR +TERMINAL TERMINAL IC581 "5" REST SW YES Laser emitted • When correctly focused "No disc" display Focus search YES Focus Servo Loop ON Disc rotates RF signal eye-pattern remains closed • When the disc correctly rotates Microprocessor commands Tracking loop closed RF signal eye-pattern opens Spindle motor (-) IC581 "7" TOC readout Acceleration Rough Servo Servo CLV 0.5 Sec 0.5 Sec Jump to the first track Play Tracking Servo Loop ON • RF signal Rough Servo Mode CLV Servo Mode (ProgramArea) CLV Servo Mode (Lead-In Area; Digital: 0) 1-12 KD-S621 Feed Section NO Is the voltage output at IC521 pin "53" 5V or 0V? Is the wiring for IC521 (90) ~ (100) correct? YES Is 5V present at IC581 pin "11"? NO Check CD 9V and 5V. YES NO YES Check the vicinity of IC521. NO Is 4V present at both sides of the feed motor? Is 6V or 2V present at IC581 "5" and "6"? YES Check the feed motor connection wiring. NO YES Check the feed motor. Check IC581. Focus Section NO When the lens is moving: Check the circuits in the vicinity of IC581 pins "15" ~ "18". 4V YES Does the S-search waveform appear at IC581 pins "17" and "18"? YES Check the pickup and its connections. Spindle Section NO Is the disk rotated? Is 4V present at IC581 pins "7" and "8" ? NO Is 4V present at IC521 pin "55" ? NO Check IC501 and IC521. YES YES YES Does the RF signal appear at TP1? Check the spindle motor and its wiring. YES Check the vicinity of IC581. NO Is the RF waveform at TP1 distorted? NO Check the circuits in the vicinity of IC501 "19" ~ "24" or the pickup YES Proceed to the Tracking section Tracking Section When the disc is rotated at first: YES Approx. 1.2 V Check the circuit in the vicinity of IC501 pins "2" ~ "12". YES Check the pickup and its connections. Is the tracking error signal output at IC501 "12"? YES Check IC521. 1-13 KD-S621 Maintenance of laser pickup (1) Cleaning the pick up lens Before you replace the pick up, please try to clean the lens with a alcohol soaked cotton swab. (2) Life of the laser diode When the life of the laser diode has expired, the following symptoms will appear. (1) The level of RF output (EFM output:ampli tude of eye pattern) will be low. Is RF output 1.0 0.35Vp-p? NO Replace it. YES O.K Replacement of laser pickup Turn off the power switch and,disconnect the power cord from the ac outlet. (3) Semi-fixed resistor on the APC PC board The semi-fixed resistor on the APC printed circuit board which is attached to the pickup is used to adjust the laser power.Since this adjustment should be performed to match the characteristics of the whole optical block, do not touch the semi-fixed resistor. If the laser power is lower than the specified value,the laser diode is almost worn out, and the laser pickup should be replaced. If the semi-fixed resistor is adjusted while the pickup is functioning normally,the laser pickup may be damaged due to excessive current. Replace the pickup with a normal one.(Refer to "Pickup Removal" on the previous page) Plug the power cord in,and turn the power on. At this time,check that the laser emits for about 3seconds and the objective lens moves up and down. Note: Do not observe the laser beam directly. Play a disc. Check the eye-pattern at TP1. Finish. 1-14 KD-S621 Description of major ICs HA13164A(IC901) : Regulator MEMORY 1.Pin layout 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 2.Block diagram +B C1 100u C2 0.1u ACC VCC 8 3 ACC BATT.DET OUT 9 ANT OUT 2 Surge Protector C3 0.1u EXT OUT 1 BIAS 6 TSD COMPOUT C4 0.1u 4 ANT CTRL VDD OUT 7 CTRL CD OUT C7 0.1u 11 5 SW5VOUT 12 C5 0.1u AUDIO OUT ILMOUT 10 14 C8 0.1u C6 10u 15 GND 13 R1 ILM AJ UNIT R: C:F note1) TAB (header of IC) connected to GND 3.Pin function Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Symbol EXT ANT ACC VDD SW5V ACC5V ANT CTRL MEMORY BATT DET 9V CTRL CD8V AJ ILMI GND Function Output voltage is VCC-1 V when M or H level applied to CTRL pin. Output voltage is VCC-1 V when M or H level to CTRL pin and H level to ANT-CTRL. Connected to ACC. Regular 5.7V. Output voltage is 5V when M or H level applies to CTRL pin. Output for ACC detector. L:ANT output OFF , H:ANT output ON Connected to VCC. Low battery detect. Output voltage is 9V when M or H level applied to CTRL pin. L:BIAS OFF, M:BIAS ON, H:CD ON Output voltage is 8V when H level applied to CTRL pin. Adjustment pin for ILM output voltage. Output voltage is 10V when M or H level applies to CTRL pin. Connected to GND. 1-15 KD-S621 AN8806SB-W (IC501) : RF & Servo amp. 1.Pin layout 36 PDAC 35 PDBD 34 PDF 33 PDE 32 PDER 31 PDFR 30 TBAL 29 FBAL 28 EF27 EF OUT 26 TE25 TE OUT 24 CROSS 23 TE BPF 22 VDET 21 LD OFF 20 VREF 19 ENV PD 1 LD 2 LDON 3 LDP 4 VCC 5 RF- 6 RF OUT 7 RF IN 8 C.AGC 9 ARF 10 C.ENV 11 C.EA 12 CS BDO 13 BDO 14 CS BRT 15 OFTR 16 /NRFDET 17 GND 18 2.Block diagram 6 29 7 28 + 9 8 27 10 + -+ RF AGC EQ 17 11 12 19 ENV CURCUIT DET 36 + VCBA - + 13 + BDO 14 OFTR 15 16 35 + + - VCBA 31 + VCBA 34 + + 32 -+ -+ + + VCBA 20 21 33 + 2 ++ 30 1-16 24 25 26 23 22 1 4 3 KD-S621 3. Pin function AN8806SB-W Pin No. Symbol I/O 1 PD I APC amp . Input terminal 2 LD O APC amp . Output terminal 3 LD ON I LD ON/OFF control terminal 4 LDP -- Connect to GND 5 VCC -- Power supply 6 RF- I RF amp . Reversing input terminal 7 RF OUT O RFamp . Output terminal 8 RF IN I AGC input terminal 9 C.AGC I/O AGC loop filter connection terminal 10 ARF O ARF output terminal 11 C.ENV I/O RF detection capacity connection terminal 12 C.EA I/O HPF-amp capacity connection terminal 13 CS BDO I/O Capacity connection terminal for RF discernment side envelope detection 14 BDO O BDO output terminal 15 CS BRT I/O Capacity connection terminal for RF discernment side envelope detection 16 OFTR O OFTR output terminal 17 /NRFDET O RFDET output terminal 18 GND -- Connect to GND 19 20 ENV O 3TENV output terminal VREF O VREF output terminal 21 LD OFF -- APC OFF control terminal 22 VDET O VDET output terminal 23 TE BPF I VDET input terminal 24 CROSS O CROSS output terminal 25 TE OUT O TE amp . Output terminal 26 TE- I FE amp . Reversing input terminal 27 FE OUT O FE amp . output terminal 28 FE- I FE amp . Reversing input terminal 29 FBAL I F.BAL control terminal 30 TBAL I T.BAL control terminal 31 PDFR I/O I-V amp conversion resistance adjustment terminal 32 PDER I/O I-V amp conversion resistance adjustment terminal 33 PDF I I-V amp input terminal 34 PDE I I-V amp input terminal 35 PD BD I I-V amp input terminal 36 PD AC I I-V amp input terminal Function 1-17 KD-S621 LA4743K(IC321):Power AMP 1.Block diagram + Vcc 1/2 + 11 - 9 - IN 1 0.022 F 20 + 6 Vcc 3/4 2200 F 7 OUT 1+ 0.22 F + TAB OUT 1- 1 PWR GND1 Protective circuit + 12 5 - IN 2 + - 8 3 OUT 2+ OUT 2- + 0.22 F PWR GND2 2 ST BY 4 Switch +5V ST ON R.F 47 F Stand by + 10 Ripple Mute Filter circuit Mute 10K 22 + 3.3 F - 15 17 - + + IN 3 19 OUT 3+ Low Level Mute ON 0.22 F + N.C OUT 3- 25 PWR GND3 Protective circuit IN 4 + 14 + - 13 + PRE GND 18 21 23 OUT 4+ OUT 4- 0.22 F ON TIME C 22 F 1-18 + 16 Muting & ON Time Control Circuit PWR GND4 24 KD-S621 2.Terminal layout 3.Pin function LA4743K Pin No. Symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 TAB GND OUTRRSTBY OUTRR+ VCC1/2 OUTRFGND OUTRF+ RIPPLE INRF INRR SGND INLR INLF ONTIME OUTLF+ GND OUTLFVCC3/4 OUTLR+ MUTE OUTLRGND NC Function Header of IC Power GND Outpur(-) for front Rch Stand by input Output (+) for front Rch Power input Output (-) for rear Rch Power GND Output (+) for rear Rch Ripple filter Rear Rch input Front Rch input Signal GND Front Lch input Rear Lch input Power on time control Output (+) for rear Lch Power GND Output (-) for rear Lch Power input Output (+) for front Muting control input Output (-) for front Power GND Non connection 1-19 KD-S621 LA6567H-X(IC541):CD DRIVE 1.Pin layout & blockdiagram CH5 V05+ 3 V04+ 4 CH4 V04- 5 V03+ 6 CH3 VC2+ 8 V02- 9 V01+ 10 CH1 11 12 27 FWD 26 S-GND 25 VCONT 24 VIN4 23 VIN4G 22 VCC-S 11K Signal system power supply 5VREG(PNPTr The outside puuting) 22K 11K VCC1 REV FR CH2 V01- 22K FR Level shift FR 7 Level shift V03- 28 Input 2 Thermal shutdown Output control V05- CH 3,4,5 Power supply Level shift 1 Level shift VCC2 CH1,2 Power supply 22K FR 21 VREF-IN 20 REG-OUT 19 REG-IN 18 VIN3G 17 VIN3 16 VIN2G 15 VIN2 22K 11K VIN1 13 VIN1G 14 11K 1-20 KD-S621 2. Pin function LA6567H-X(2/2) Pin no. Symbol Function 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 VCC2 V05V05+ V04+ V04V03+ V03V02+ V02V01+ V01VCC1 VIN1 VIN1G VIN2 VIN2G VIN3 VIN3G REG-IN REG-OUT VREF-IN VCC-S VIN4G VIN4 VCONT S-GND FWD CH3,4,5 Power supply( It is short with VCC1,VCC-S) Loading output(-) Loading terminal (+) CH4 Output terminal(+) CH4 Output terminal(-) CH3 Output terminal(+) CH3 Output terminal(-) CH2 Output terminal(+) CH2 Output terminal(-) CH1 Output terminal(+) CH1 Output terminal(-) CH1,2(BTL) Power supply(It is short with VCC-S,VCC2) CH1 Input terminal CH1 Input terminal(For gain adjustment) CH2 Input terminal CH2 Input terminal(For gain adjustment) CH3 Input terminal CH3 Input terminal(For gain adjustment) Regulator terminal(Outside putting PNP base) Regulator terminal(Outside putting PNP collector) Standard voltage input terminal Signal system power supply(It is short with VCC1,VCC2) CH4 Input terminal(For gain adjustment) CH4 Input terminal 5CH(VLO) Output voltage set terminal Signal system GND 5CH(VLO)Signal output switch terminal(FWD),Input of logic of loading part 28 REV 5CH(VLO)Signal output switch terminal(REV), Input of logic of loading part Frame(FR)at the center becomes system GND. Please be short-circuited on the outside and use the terminal of the power supply system and three teminals of VCC-S, VCC1,VCC2. 1-21 KD-S621 LC72366-9A73 (IC801) : System CPU 1. Pin layout ~ 1 ~ 64 65 40 41 80 ~ ~ 25 24 2. Pin function Pin No. Symbol 1 XIN 2 TEST2 3 J-BUS SI 4 J-BUS SO 5 J-BUS SCK 6 J-BUS I/O 7 SUBQ 8 9 SQCK 10 RESET 11 LCD SI 12 LCD SO 13 LCD SCK 14 LCD CE 15 FM ILLUMI 16 AM ILLUMI 17 CD ILLUMI 18 DIMMER OUT 19 LM0 20 LM1 21 22 23 24 KS2 25 KS1 26 KS0 27 DETACH 28 K2 29 K1 30 K0 31 Vdd 32 SW2 33 CD LSI RESET 34 MCLK 35 MDATA 36 MLD 37 38 39 SCL 40 SDA 1-22 I/O I I I/O I/O I O O O O O O O O I I I I O O O O O O Function Crystal oscillator input port Connect to ground No use No use No use No use CD LSI subcode data input No use CD LSI subcode clock Micon reset pin No use LCD driver data output LCD driver clock signal LCD driver chip enable port No use No use No use No use CD loading motor output CD loading motor output No use No use No use Output for initial setting diode matrix Output for initial setting diode matrix Output for initial setting diode matrix Front panel detect No use Input for initial setting diode matrix Input for initial setting diode matrix 5V power supply port (+B) CD mechanism detect switch CD LSI reset CD LSI command clock signal CD LSI command data output CD LSI command load signal No use No use E.volume clock output E.volume data output KD-S621 LC72366-9A73(2/2) Pin No. Port Name I/O 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 CD ON RELAY BLKCK BEEP SW4 SW1 SW3 REST FLOCK TLOCK CD SENSE STATUS P.SAVES2 SD/ST REMOCON J BUS INT BAND MONO IFRQ/AGC I I I I I I I I I I I I O O 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 O MUTE I LEVEL I S.METER KEY CHANGE I KEY2 I KEY1 I KEY0 I P.SAVE1 I SENSE FM IF COUNT I NC NC Vdd I AM OSC I FM OSC VSS NC O E0 TEST1 O XOUT Function CD 8V supply on 5V power contorl Sub-code/block/clock signal output No use CD mechanism detect switch CD mechanism detect switch CD mechanism detect switch CD pickup rest position Focus lock signal output Active:Low Tracking lock signal output Active :low CD LSI sense signal CD LDI status signal power save 2:+B detect Station detection,Stereo signal input H:SD Remocon input No use FM/AM band selection FM mono selection During FM auto search,IF request output H after SD detected. During AM suto search,AGC output Muting switch Level meter input S meter input Control to GND Key 2 input port Key 1 input port Key 0 input port Power save 1,ACC power detection Voltage sensor port No use FM frequency detecting No use No use 5V power supply (+B) No use FM limited signal input Ground port for power supply No use Error signal output port for PLL Test port for LSI, To connect ground 4.5MHz crystal oscillator output 1-23 KD-S621 LC75823W (IC601) : LCD driver DI CL CE OSC Vss VDD2 VDD1 INH VDD COM3 COM2 COM1 S52 S51 S50 S49 1. Pin Layout & Symbol 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 1 48 2 47 3 46 4 45 5 44 6 43 7 42 8 41 9 40 10 39 11 38 12 37 13 36 14 35 15 34 16 33 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 S48 S47 S46 S45 S44 S43 S42 S41 S40 S39 S38 S37 S36 S35 S34 S33 S17 S18 S19 S20 S21 S22 S23 S24 S25 S26 S27 S28 S29 S30 S31 S32 S1 S2 S3 S4 S5 S6 S7 S8 S9 S10 S11 S12 S13 S14 S15 S16 2. Pin Function Pin No. 1 to 52 Symbol S1 to S52 64 DI I/O Function O Segment output pins used to display data transferred by serial data input. 53 to 55 COM1 to COM3 O Common driver output pins. The frame frequency is given by : t0=(fosc/384)Hz. VDD 56 -- Power supply connection. Provide a voltage of between 4.5 and 6.0V. INH 57 I Display turning off input pin. INT="L" (Vss) ----- off (S1 to S52, COM1 to COM3="L" INT="H" (VDD)----- on Serial data can be transferred in display off mode. VDD1 58 I Used for applying the LCD drive 2/3 bias voltage externally. Must be connected to VDD2 when a 1/2 bias drive scheme is used. VDD2 59 I Used for applying the LCD drive 1/3 bias voltage externally. Must be connected to VDD1 when a 1/2 bias drive scheme is used. Vss 60 -- Power supply connection. Connect to GND. OSC 61 I/O Oscillator connection. An oscillator circuit is formed by connecting an external resistor and capacitor at this pin. Serial data CE : Chip enable 62 CE interface connection CL CL : Sync clock 63 I to the controller. 1-24 DI : Transfer data KD-S621 TEA6320T-X (IC301) : E.volume 1.Pin layout 2.Block diagram 10 SDA GND OUTLR OUTLF TL B2L B1L IVL ILL QSL IDL MUTE ICL IMD IBL IAL 1 2 3 4 5 6 7 8 9 10 11 12 13 CD-CH 14 15 TAPE 16 TUNER 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 SCL VCC OUTRR OUTRF TR B2R B1R IVR ILR QSR IDR Vref ICR CAP IBR IAR 21 31 2 19 16 15 13 11 14 8 9 7 6 5 12 MUTE FUNCTION ZERO CROSS DETECTOR POWER VOLUME 2 0 to 55 dB BALANCE FENDER REAR 3 VOLUME 2 0 to 55 dB BALANCE FENDER FRONT 4 SUPPLY VOLUME 1 +20 to -31 dB LOUDNESS LEFT BASS LEFT +15 dB TREBLE LEFT +12 dB HC BUS REC LOGIC 32 1 SOURCE SELECTOR VOLUME 1 +20 to -31 dB LOUDNESS RIGHT 22 20 18 17 23 25 BASS RIGHT +15 dB 24 26 27 TREBLE RIGHT +12 dB VOLUME 2 0 to -55dB BALANCE FENDER FRONT 29 VOLUME 2 0 to -55dB BALANCE FENDER REAR 30 28 3.Pin functions Pin No. Symbol I/O Functions I/O Serial data input/output. Pin No. Symbol I/O Functions 17 IAR I Input A right source. Ground. 18 IBR I Input B right source. O output left rear. 19 CAP - Electronic filtering for supply. O output left front. 20 ICR I Input C right source. 21 Vref - Reference voltage (0.5Vcc) 22 IDR - Not used 1 SDA 2 GND - 3 OUTLR 4 OUTLF 5 TL I 6 B2L - Treble control capacitor left channel or input from an external equalizer. Bass control capacitor left channel or output to an external equalizer. 7 B1L - Bass control capacitor left channel. 23 QSR O Output source selector right channel. 8 IVL I Input volume 1. left control part. 24 ILR I Input loudness right channel. 9 ILL I Input loudness. left control part. 25 IVR I Input volume 1. right control part. 10 QSL O Output source selector. left channel. 26 B1R - Bass control capacitor right channel 11 IDL - Not used 27 B2R O 12 MUTE - Not used 28 TR I 13 ICL I Input C left source. 29 OUTRF O Output right front. 14 IMO - Not used 30 OUTRR O Output right rear. 15 IBL I Input B left source. 31 Vcc - Supply voltage. 16 IAL I Input A left source. 32 SCL I Serial clock input. Bass control capacitor right channel or output to an external equalizer. Treble control capacitor right channel or input from an external equalizer. 1-25 KD-S621 NJM4565M-WE (IC151) : Ope. amp A OUTPUT 1 1-26 8 V+ A - INPUT 2 7 B OUTPUT A+INPUT 3 6 B - INPUT V- 4 5 B+INPUT KD-S621 Block diagram CJ701 ANT 5 TU701 FM/AM TUNER LOADING MOTOR FEED MOTOR SPINDLE MOTOR SW1 SW4 PICK UP LOADING SPINDLE FEED TRACKING FOCUS LOADING FEED TRV,TVD,ECM,ECS, KICK,TRD,FOD IC561 DSP & DAC OUT L OUT R VA,VB,VC VE,VF,MD,LD SPINDLE SW1 IC541 SERVO BTL DRIVER MONO EQ CN501 4 LM0 LM1 REST REST SWITCH IC501 RF AMP TBAL FBAL FE,TE TRCRS VDET LDON ARF BDO OFTR RFDET RFENV SW4 A,B,C LD,MD E,F,TRACKING FOCUS 3 IC151 CD LPF CD,SENSE CD,RESET STATUS SUBQ,SQCK BLKCK,TLOCK FLOCK,MLD MDATA,MCLK TU.LCH TU.RCH FM/AM FM.OSC IFC AGC S.METER SD/ST LRO RRO IC321 POWER AMP IC301 E.VOL SDA SCL CJ302 LINE OUT OUT LF OUT RF OUT LR OUT RR IC801 MICON CD LCH CD RCH CD.LCH CD.RCH LF RF LR RR IC901 REGULATOR EACH BLOCK SPK BATTERY S601 S620 KEY MATRIX IC602 REMOCON KEY0 KEY1 KEY2 LCD1 COM1 COM2 COM3 S1 S48 IC601 LCD DRIVER CN801 CJ601 REMOCON 2 LCD_CLK LCD_SO LCD_LE 1 A B C D E F G 2-1 KD-S621 Standard schematic diagrams KD-S621 Main amp section TU701 QAU0257-001 CJ701 QNB0100-002 L701 Q861 DTA114EKA-X 4.7u R799 C862 Q701 DTC114EKA-X 0.01 1SS355-X 2.2k Q332 2SD1781K/QR/-X R436 Q432 2SD1781K/QR/-X R434 2.2k R433 1SS355-X RRO 1k 100 R708 C711 R336 TU.RCH MONO TU.LCH R798 22k SW5V AGC S.METER Q702 DTC144EKA-X 15 R796 100 D332 D333 47k R704 8.2k C715 15 R795 FM/AM 9V EO FM.OSC IFC 1k R792 Q793 DTC114EKA-X 2SC2412K/R/-X 10k R793 R794 Q732 D792 1SS355-X C733 2SC2412K/R/-X D731 Q731 4 2.2k 10k D791 1SS355-X 1k C732 0.001 R734 470 R733 MTZJ10B-T2 2.2/50 R732 220/10 C731 10k C713 R702 R791 Q792 2SA1037AK/RS/-X SD/ST R731 1.5k R334 LRO Q791 2SB1197K/QR/-X CJ321 QNN0170-001 1SS355-X D866 1SS355-X D868 1SS355-X D861 MTZJ4.7B-T2 C861 220/6.3 R333 1k 0.082 1/50 C201 R862 1/50 C101 R102 R202 220/10 0.1/50 C712 10k R705 C709 C710 *C714 C720 R725 0.1/50 0.01 0.1/50 0.022 C703 C718 C702 220p 47/10 C716 C725 1SS254-T2 1SS254-T2 D701 D702 C717 C701 10 R797 1k D869 1k R701 470 R201 R101 R703 470 1SS355-X R861 D867 MUTE 5 IC321 47k R304 47k 4.7/25 C419 C420 220p 220p LR- LF+ LF- R322 470 D904 RF+ C327 4.7/25 9V SW5V CRS03-W 47k C902 D903 2200/16 Q902 1SS254-T2 D901 1N5401-TU-15 2SC2412K/R/-X L901 220/10 R907 RF+ RR+ LR+ LF+ 0.1 C914 RFRRLRLF- C904 22/16 F1 QMFZ047-150-T C903 22/16 0.1 R901 9.1k 0.01 22/16 C905 C906 100/10 C908 C907 R903 100/10 C909 4.7k R905 R904 100K 4.7k R906 68k R909 27k R908 47k Q903 2SA1037AK/RS/-X R910 39k QQR0703-001 KEY1 KEY0 CD8V D902 SB10-03A3-T2 C901 C911 D321 1SS254-T2 Q321 DTC114EKA-X 0.01 R5V C910 0.01 47k IC901 HA13164A 4.7u R823 L801 4.7k 47k 47k 47k 47k 47k VDD KEY2 S.METER R831 R829 R828 R827 R826 R825 RF- R321 47k C329 4.7/25 22k R830 4.7k 47k FM/AM MONO AGC 2.2k R817 0 R844 R818 0 REMOCON 47k SD/ST 47k 47k 47k R845 STATUS 47k 47k R816 R840 R841 R842 REST FLOCK TLOCK CD.SENSE R814 R815 R822 0 R843 47k SW4 SW1 SW3 R807 C432 0.1 MUTE 47k 47k R404 R403 2.2k 1/50 C433 0.1 C321 100/16 RR+ RR- 100/10 C309 C310 0.01 4.7/25 0.18 C402 0.0082 C403 C311 100/10 C312 R402 27k 10k 47k R810 100k R809 IC801 C328 47/16 C331 0.022 C330 0.022 2.2 22k C434 C915 R832 22k R407 R911 3.3k SDA LR+ C319 220p R303 4.7/25 C308 C306 C320 220p C435 1/50 R323 1k 4.7k 22k 4.7k R834 R835 SCL 3.3k C408 0.033 4.7/25 0.22 R401 220/6.3 10/16 R833 R811 R812 D828 D827 D826 47k D810 C807 BLKCK UDZS6.2B-X UDZS6.2B-X UDZS6.2B-X UDZS6.2B-X UDZS6.2B-X UDZS6.2B-X UDZS6.2B-X D824 D825 UDZS6.2B-X 0.1 D823 0.1 C822 C823 D821 0.01 C801 IFC LC72366-9A73 D822 0.1 C821 1SS355-X R836 SW2 CD.RESET MCLK MDATA 47/16 TU.RCH C802 0.0056 C405 C407 C404 C406 EO FM.OSC R813 KEY1 KEY2 1/50 C804 33p 1k C333 0.1 C427 22/16 C335 R808 DETACH MLD GND RRO SDA X801 27k QAX0406-001Z 1SS254-T2 22p ILL_10V LCD.SCK LCD.SO LCD.CE KEY0 R308 0.033 TU.LCH R5V REMOCON 0.0056 C307 R302 2.2k 0.18 C302 0.0082 C303 C305 R408 DETACH 2 C304 4.7k CD.LCH 9V 22k C803 CD.RCH CN801 VMC0334-001 CD.LCH CD.RCH SUBQ SQCK 10K R801 LCD.SO D801 C332 0.1 R301 TEA6320T-X 0.22 1SS254-T2 MCLK BLKCK IC301 R307 C334 1/50 27k 27k 1SS254-T2 D804 MLD MDATA 3.3k 1SS254-T2 D802 TLOCK FLOCK CD.SENSE R803 SUBQ SQCK 3.3k 3.3k 1SS254-T2 D805 R805 R804 LM1 LM0 D803 CD.RESET STATUS 3 LCD.CE LCD.SCK ILL_10V ILL_10V REST SW1 SW2 SW3 SW4 LM1 LM0 CD8V LRO SCL LA4743K C916 2.2/50 R902 1k 1 Tuner Signal CD signal Parts are safety assurance parts. When replacing those parts make sure to use the specified one. A B C 2-2 D E F Front signal Rear signal G H KD-S621 LM1 TRD 220/10 KICK TRV REST 620 R541 8.2k IC561 MCLK SW4 0.01 R561 1k R564 1k R563 1k R562 1k R568 1k R567 1k R579 1k R569 1k SW3 LM1 LM0 4.3k 150k R547 C542 R548 MN6627482WA 0.0047 R551 22/16 Q541 2SA1706/ST/-T R570 1k C541 0.033 R549 20k C562 0.01 C543 SW2 C561 TLOCK FLOCK CD.SENSE MLD MDATA STATUS SUBQ SQCK BLKCK SW1 CD.RESET TVD FOD 4.3k 12k 56k R545 R546 DSK10C-T1 R542 ECS R544 R543 5 3.3k 30k ECM C552 D551 0.01 C551 LM0 CD servo & control section CD8V CD.RESET TRV TVD IC541 STATUS SUBQ LA6557H-X ECM ECS KICK TRD FOD 4 SQCK TLOCK FLOCK R550 MLD C573 MDATA 220/6.3 MCLK OFTR TRCRS RFDET BDO TRACKING+ TRACKING- FOCUSFOCUS+ FEED+ FEED- LOADING+ SPINDLESPINDLE+ CD.SENSE 0.01 TE RFENV VDET 6.8k LOADING- C574 FBAL TBAL FE BLKCK R560 CD.RCH 100( 1/8W) LDON GND CD.LCH VB 12k R516 VA 12k R517 TE TP R508 100k C521 560p C520 47p GND IC2 BT BT GNDGND C572 100/10 C571 0.001 C579 220 R575 0.1 0.01 C153 12k 150p 47/6.3 R154 R156 22k 22k IC151 NJM4565M-WE C251 0.001 C513 330p R519 C512 R254 R256 22k 22k C255 47/6.3 0.01 1M C511 0.0047 C510 0.027 100p C509 1/50 C508 R251 18k L501 C252 4.7/25 R252 C253 12k 150p R253 R255 27k 1.5k 4.7U C256 3.9k R504 0.1 C507 3p C506 C505 0.01 100/10 C504 68p C530 1k C503 68p R503 C502 100/10 RF RFDET OFTR BDO LDON TP ARF R502 22 R501 VCC 22 1.5k GND MD C527 0.022 R155 27k R152 C155 BT BT C151 0.001 GND IC501 R153 4.7/25 GND AN8806SB-W 0.01 C577 C152 18k Q501 2SA1706/ST/-T 0 RFENV R151 C501 R576 22k 0.047 R509 22k 12k LD 0 0.0015 R506 C519 QGB2027M1-26S 2 R581 220 R574 C576 0.47 0.01 C568 C567 100/10 0.1 C565 C566 100k 33k R577 R571 220k 0.27 R580 C564 C529 0.0012 0.0018 VDET TRCRS TE FE FBAL FE TP 4.7U 0.022 L561 0.001 12k R515 0.1 56k R514 TP C514 R513 VC 33k 220k VF C523 0.22 R505 0.022 C525 R507 0.001 R573 X561 QAX0714-001Z 100/10 CN501 56k VREF C515 VB VF VCC C522 0.01 VC VE VA C524 C516 VB VF VCC VREF MD R512 VE 4.7U 0.001 ARF 100/10 VC VE VA TRACKING+ FOCUS+ FOCUS- 8.2k C518 MD VR SW2 SW1 SW3 SW4 LD TRACKING- 8.2k FOCUSVREF TP R518 LD TRACKINGTRACKING+ FOCUS+ L562 C563 ARF C528 SW2 SW1 SW3 SW4 3 SPINDLESPINDLE+ REST LOADING+ LOADINGGND TBAL SPINDLE+ REST LOADING+ LOADING- FEEDFEED+ R511 270k R510 150k FEEDFEED+ SPINDLE- 1 CD signal A B C D E F G 2-3 KD-S621 KD-S621 LCD & key control section 5 4 C611 0.012 D644 LCD1 QLD0210-002 R661 C612 4.7/6.3 R662 470 IC602 RPM6938-SV4 UDZS5.1B-X CJ601 VMC0335-001 10k ILL_10V R5V S35 S34 S33 S48 S47 S46 S45 S44 S43 S42 S41 S40 S39 S38 S37 S36 COM3 COM1 COM2 S45 S46 S47 S48 S39 S40 S41 S42 S43 S44 S37 S38 S36 S34 S35 S29 S30 S31 S32 S33 S21 S22 S23 S24 S25 S26 S27 S28 S19 S20 S17 S18 S12 S13 S14 S15 S16 S10 S11 S6 S7 S8 S9 S1 S2 S3 S4 S5 REMOCON LCD.SCK LCD.SD LCD.CE KEY0 IC601 LC75823W KEY1 KEY2 R607 R606 560 680 VOL+ LOUD 2 6 D602 D604 D608 D612 VOL- S620 S619 S618 S617 S616 CD PL602 POWER S615 R653 DOWN D605 D609 D614 D617 4 EJECT AM LCD.SD R654 R655 R631 R632 R633 D643 S21 S20 S19 S18 S17 10k 10k 10k 10k R656 D642 820 820 820 510 510 S26 S25 S24 S23 S22 D619 DISP R634 680 KEY2 D641 UDZS5.1B-X R652 2.2k R612 1.5k 560 S607 S608 D616 SCM R635 R613 UP D613 R636 680 S609 COM3 D645 LCD.CE LCD.SCK 1.5k R614 MODE 3 D620 PL601 FM R637 910 S610 510 R615 820 1.2k S611 R644 R616 R645 1.5k S612 R643 R617 820 S613 SEL D618 D615 KEY1 270 R608 680 R638 910 D611 270 R609 1.2k D607 R639 R610 1.5k 270 R611 D603 COM1 COM2 R651 2.2k 1SS355-X 1SS355-X R658 180k S16 D601 5 S8 S9 S10 S11 S12 S13 S14 S15 S601 S602 D610 1 270 S603 D606 R640 S604 R641 S605 510 S606 KEY0 S1 S2 S3 S4 S5 S6 S7 680 R657 51k R601 560 680P R602 680 C602 R603 910 C601 0.022 R604 1.2k UDZS6.2B-X R605 R642 3 GND S32 S31 S30 S29 S28 S27 S614 C603 10/6.3 2 1 A B C 2-4 D E F G H 17 3-2 18 6 20 25 6 29 24 19 21 1 22 6 2 27 23 26 Front board 28 7 33 14 31 10 30 15 7 32 31 9 36 11 16 3 34 38 12 13 Main board 43 35 9 45 41 40 44 8 39 48 8 48 42 47 5 46 8 4 KD-S621 Exploded view of general assembly and parts list Block No. M 1 M M KD-S621 Parts list (General assembly) A A Item Parts number Block No. M1MM Parts name Description Q'ty 1 ------------ CD MECHA 1 TN-CCD1001Z 2 FSJC1029-404 TOP CHASSIS 1 3 FSMH3001-202 SIDE PANEL 1 4 FSKM3011-002 BOTTOM COVER 1 5 FSMA3004-203 INSULATOR 1 6 QYSDST2604Z SCREW 3 CHASSIS+MECHA BKT 7 FSKZ4005-001 SCREW 2 CHASSIS+SIDE PANEL 8 QYSDST2604Z SCREW 3 CHASSIS+REAR BKT 9 QYSDST2606Z SCREW 2 CHASSIS+MAIN PWB 10 FSKZ4005-001 SCREW 1 SIDE PANEL+IC BKT 11 FSJC2013-013 FRONT CHASSIS 1 12 FSKS3010-001 LOCK LEVER 1 13 FSKW4005-003 TORSION SPRING 1 FOR LOCK LEVEL 14 FSXP3026-002 RLS KNOB 1 15 FSKW3002-015 COMP.SPRING 1 16 FSPK3009-002 BLIND 1 17 GE10037-001A FRONT PANEL 1 18 GE30300-008A FINDER ASSY 1 19 GE20119-001A PRESET BUTTON 1 20 GE30304-001A POWER BUTTON 1 21 GE30305-001A EJECT BUTTON 1 22 GE20131-001A D FUNC BUTTON 1 FM/CD/AM 23 GE30307-001A SND FTN BUTTON 1 24 GE20130-001A PUSH BUTTON 1 25 GE20118-001A +/- BUTTON 1 26 GE20120-001A UP/DOWN BUTTON 1 27 GE30306-001A DETACH BUTTON 1 28 FSKW3002-012 COMP. SPRING 1 FOR DETACH BUTTON 29 GE30117-001A LIGHT LENS 1 30 GE10038-001A REAR COVER 1 31 VKZ4777-001 MINI SCREW 4 FRONT+REAR 32 QLD0210-002 LCD 1 33 GE30302-002A LCD CASE 1 34 FSJK3035-001 LCD LENS 1 35 FSKS3022-003 LENS CASE 1 36 FSYH4078-002 LIGHTING SHEET 1 38 QNZ0442-001 RUBBER CONNE 1 39 GE30348-002A NAME PLATE 1 40 QMFZ047-150-T FUSE 1 41 VMA4652-001SS EARTH PLATE 1 42 FSKM3010-020 REAR BRACKET 1 43 FSKL4024-001 IC BRACKET 1 44 GE40104-001B HEAT SINK 1 45 GE40103-001A REGULATOR BKT 1 46 QYSDST2606Z SCREW 1 FOR ANT 47 QYSDSF3006Z SCREW 1 LINE OUT 48 QYSDST2606Z SCREW 3 16P & TR BRACK Area 3-3 KD-S621 CD mechanism assembly and parts list Grease G-31SA G-31SA(Bottom side) RX-405 Block No. M B M M TN-CCD1001Z-136J 102 23 102 49 23 1 101 101 101 14 101 15 100 17 12 10 16 70 13 100 11 7 71 90 19 3 18 113 105 8 6 91 68 d 65 2 4 7 62 b 9 5 b 64 20 a 43 66 c 110 67 61 62 72 48 41 86 103 113 80 50 135 134 42 49 104 40 51 107 79 102 88 c 49 84 82 81 116 22 92 117 d 131 36 d 107 93 89 57 52 109 130 132 107 33 62 3-4 63 107 22 101 a 38 56 133 39 32 108 106 29 106 108 KD-S621 Parts list (CD mechanism) A Item Block No. MBMM Parts number Parts name Description Q'ty 1 30310101T FRAME 1 2 30310103T DANPER PIN 2 3 30310107T UPPER PLATE 1 4 30310108T SEL STOP PLATE 1 5 30310142T SEL ARM (L)L 1 6 30310143T SEL ARM (R)L 1 7 30310145T S ARM SPRING(L) 2 8 30310112T TRIG LEVER 1 9 30310155T TRIG PL(Z) 1 10 30310115T TRIG PL SPRING 1 11 30310116T TRIG ARM 1 12 30310134T FIX ARM (L)B 1 13 30310159T FIX ARM (R)Z 1 14 30310150T FIX PL (L)Z 1 15 30310156T FIX PL (R) Z 1 16 30310138T LDG GR (6)B 1 17 30310122T LDG GEAR (6)SP 1 18 30310148T S.L ARM(N) 1 19 30310125T S.L ARM SPRING 1 20 30310149T REAR DAM BKT(Z) 1 22 30310151T HUNG UP SP (FZ) 2 23 30310129T HUNG UP SP (R) 2 29 30300510T PU GEAR(B) 1 32 30310544T F.M.BASE(Z) 1 33 30310547T FD GR BLK(Z) 1 36 30310546T PU GUIDE(Z) 1 38 30310533T THRUST SPR(M) 1 39 30310548T PU M NUT(Z) 1 40 30310512T NUT PUSH SPR PL 1 41 30310558T CLP ARM(Z) 1 42 30310514T CLP ARM SPRING 1 43 30310552T CLAMPER(Z) 1 48 30310557T CLAMPER PLATE(Z 1 49 30310524T DAMPER (J) 3 50 30310525T CLP ARM SPR (L) 1 51 30310545T F SCREW GUIDE(Z 1 52 30310556T PU G.SP PLT(Z) 1 56 64180405T DET SW 1 ESE11SF4 57 OPTIMA-720L1 C.D PICK (CAR) 1 61 30311035T FPC HOLDER(Z) 1 62 19501403T WIRE CLAMPER 3 63 30311037T PICK UP FPC(Z) 1 64 30311036T CONNECT.PCB(Z-J 1 65 30311038T WIRE (5P-Z) 1 66 30311039T WIRE (LD-Z) 1 67 30311040T WIRE (FD-Z) 1 68 30311041T WIRE (RS-Z) 1 70 64180402T DET SWITCH 2 ESE22MH1 Area 3-5 KD-S621 Parts list (CD mechanism) A 3-6 Item Block No. MBMM Parts number Parts name Description Q'ty 71 64180403T DET SWITCH 2 ESE22MH3 72 68150232T CONNECTOR 1 TKC-W26X-C1 79 30311105T SOPPORT PLATE 1 80 30311138T GR MT BLK(N) 1 81 30311109T LDG GEAR (2) 1 82 30311110T LDG GEAR (3) 1 84 30311112T LDG GEAR (5) 1 86 30311136T LDG ROLLER 2 88 30311118T L.P SPRING (L) 1 89 30311119T L.P SPRING (R) 1 90 30311123T SW PCB 1 91 30311124T SW ACTUATOR 1 92 30311129T LDG BELT 1 93 30311140T FRONT BRKT (J) 1 100 9C0620503T C B TAP SCREW 2 M2X5 101 9C2020401T C SCREW TS.G 5 M2X4 102 9C4320403T C B TAP SCREW 4 M2X4 103 9C0117223T SCREW 2 M1.7X2.2 104 9C0917703T C TAP SCREW S3 1 M1.7X7 105 9C0320201T C TAP SCREW S3 1 M2X2 106 9C4920013T C TAP SCREW S3 2 M2X10 107 9C4920603T C TAP SCREW B3 4 M2X6 108 9P0220031T TAMS SCREW 2 M2X3 109 9C0314203T C TAP SCREW 1 M1.4X2 110 9C0420253 C TAP SCREW 1 M2X2.5 113 9W0330276 NW BLUE 2 2.9X5X0.3 116 9W0725030T LUMILAR W 1 2.3X9.8X0.25 117 9W0640030T WASHER 1 1.4X3.2X0.4 130 303105310T FEED MO ASSY 1 131 303105311T SPINDLE MO ASSY 1 132 303105312T FEED SCREW ASSY 1 133 303111301T LDG MOTOR ASSY 1 134 303111302T RDG RLR SFT ASY 1 135 303105502T T.T.BASE ASSY 1 Area KD-S621 Electrical parts list (Main board) A Item Parts number Parts name C 101 QERF1HM-105Z E CAPACITOR C 151 NCB31HK-102X C CAPACITOR C 152 QEKJ1EM-475Z E CAPACITOR C 153 NDC31HJ-151X C CAPACITOR C 155 QEKJ0JM-476Z E CAPACITOR C 201 QERF1HM-105Z E CAPACITOR C 251 NCB31HK-102X C CAPACITOR C 252 QERF1EM-475Z E CAPACITOR C 253 NDC31HJ-151X C CAPACITOR C 255 QERF0JM-476Z E CAPACITOR C 256 QERF1AM-107Z E CAPACITOR C 302 NCB31HK-822X C CAPACITOR C 303 NCB21CK-184X C 304 Block No. 01 Remarks 1.0MF 20% 50V Area A Item Parts number Parts name Remarks C 516 QEKJ1AM-107Z E CAPACITOR C 518 NCB31AK-224X C CAPACITOR C 519 NCB31EK-473X C CAPACITOR C 520 NDC31HJ-470X C CAPACITOR 47MF 20% 6.3V C 521 NCS31HJ-561X C CAPACITOR 1.0MF 20% 50V C 522 NCB31HK-223X C CAPACITOR C 523 NCB31HK-223X C CAPACITOR C 524 NCB31HK-102X C CAPACITOR C 525 NCB31HK-102X C CAPACITOR 47MF 20% 6.3V C 527 NCB31EK-223X C CAPACITOR 100MF 20% 10V C 528 NCB31HK-182X C CAPACITOR C 529 NCB31HK-122X C CAPACITOR C CAPACITOR C 530 NDC31HJ-680X C CAPACITOR NCB21CK-224X C CAPACITOR C 541 QERF1CM-226Z E CAPACITOR C 305 NCB21HK-333X C CAPACITOR C 542 NCB31HK-472X C CAPACITOR C 306 NCB31HK-562X C CAPACITOR C 543 NCB31EK-333X C CAPACITOR C 307 QERF1EM-475Z E CAPACITOR 4.7MF 20% 25V C 551 QERF1AM-227Z E CAPACITOR C 308 QERF1EM-475Z E CAPACITOR 4.7MF 20% 25V C 552 NCB31EK-103X C CAPACITOR C 309 QEKJ1AM-107Z E CAPACITOR 100MF 20% 10V C 561 NCB31EK-103X C CAPACITOR C 310 NCB31HK-103X C CAPACITOR C 562 NCB31EK-103X C CAPACITOR C 311 QEKJ1AM-107Z E CAPACITOR 100MF 20% 10V C 563 NCB31HK-102X C CAPACITOR C 312 QEKJ1CM-476Z E CAPACITOR 47MF 20% 16V C 564 NCB21CK-274X C CAPACITOR C 319 NCS31HJ-221X C CAPACITOR C 565 NCB31EK-104X C CAPACITOR C 320 NCS31HJ-221X C CAPACITOR C 566 NCB31AK-474X C CAPACITOR C 321 QERF1CM-107Z E CAPACITOR 100MF 20% 16V C 567 QERF1AM-107Z E CAPACITOR C 327 QEKJ1EM-475Z E CAPACITOR 4.7MF 20% 25V C 568 NCB31EK-103X C CAPACITOR C 328 QEKJ1CM-476Z E CAPACITOR 47MF 20% 16V C 571 NCB31EK-103X C CAPACITOR C 329 QEKJ1EM-475Z E CAPACITOR 4.7MF 20% 25V C 572 QEKJ1AM-107Z E CAPACITOR 100MF 20% 10V C 330 NCB31HK-223X C CAPACITOR C 573 QERF1AM-227Z E CAPACITOR 220MF 20% 10V C 331 NCB31HK-223X C CAPACITOR C 574 NCB31EK-103X C CAPACITOR C 332 NCB31EK-104X C CAPACITOR C 576 NCB31HK-152X C CAPACITOR C 333 NCB31EK-104X C CAPACITOR C 577 NCB31EK-104X C CAPACITOR C 334 QERF1HM-105Z E CAPACITOR 1.0MF 20% 50V C 579 NCB31HK-102X C CAPACITOR C 335 QERF1HM-105Z E CAPACITOR 1.0MF 20% 50V C 701 QERF1AM-476Z E CAPACITOR 47MF 20% 10V C 402 NCB31HK-822X C CAPACITOR C 702 QEKJ1HM-104Z E CAPACITOR .10MF 20% 50V C 403 NCB21CK-184X C CAPACITOR C 703 QERF1HM-104Z E CAPACITOR .10MF 20% 50V C 404 NCB21CK-224X C CAPACITOR C 709 NCB31EK-223X C CAPACITOR C 405 NCB21HK-333X C CAPACITOR C 710 NCB31EK-223X C CAPACITOR C 406 NCB31HK-562X C CAPACITOR C 711 NCB31EK-103X C CAPACITOR C 407 QERF1EM-475Z E CAPACITOR 4.7MF 20% 25V C 712 QEKJ1HM-104Z E CAPACITOR C 408 QERF1EM-475Z E CAPACITOR 4.7MF 20% 25V C 713 NDC31HJ-101X C CAPACITOR C 419 NCS31HJ-221X C CAPACITOR C 714 NCB31HK-103X C CAPACITOR C 420 NCS31HJ-221X C CAPACITOR C 715 NDC31HJ-151X C CAPACITOR C 427 QEKJ1CM-226Z E CAPACITOR C 717 NCS31HJ-221X C CAPACITOR C 432 NCB31EK-104X C CAPACITOR C 718 NCB31EK-223X C CAPACITOR 4.7MF 20% 25V 4.7MF 20% 25V 22MF 20% 16V C 433 NCB31EK-104X C CAPACITOR C 720 QERF1AM-227Z E CAPACITOR C 434 QERF1HM-105Z E CAPACITOR 1.0MF 20% 50V C 725 NCB31EK-103X C CAPACITOR C 435 QERF1HM-105Z E CAPACITOR 1.0MF 20% 50V C 731 QERF1HM-225Z E CAPACITOR C 501 NCB31EK-103X C CAPACITOR C 732 NCB31HK-102X C CAPACITOR C 502 QEKJ1AM-107Z E CAPACITOR C 503 NCS31HJ-680X C CAPACITOR C 504 QEKJ1AM-107Z E CAPACITOR C 505 NCB31EK-103X C 506 NDC31HJ-3R0X C 507 100MF 20% 10V 22MF 20% 16V 220MF 20% 10V 100MF 20% 10V .10MF 20% 50V 220MF 20% 10V 2.2MF 20% 50V C 733 QERF1AM-227Z E CAPACITOR 220MF 20% 10V C 801 QEKJ0JM-227Z E CAPACITOR 220MF 20% 6.3V C 802 NCB31EK-103X C CAPACITOR C CAPACITOR C 803 NDC31HJ-220X C CAPACITOR C CAPACITOR C 804 NDC31HJ-330X C CAPACITOR NCB31EK-104X C CAPACITOR C 807 QERF1CM-106Z E CAPACITOR C 508 QEKJ1HM-105Z E CAPACITOR C 821 NCB31EK-104X C CAPACITOR C 509 NDC31HJ-101X C CAPACITOR C 822 NCB31EK-104X C CAPACITOR C 510 NCB31EK-273X C CAPACITOR C 823 NCB31EK-104X C CAPACITOR C 511 NCB31HK-472X C CAPACITOR C 861 QEKJ0JM-227Z E CAPACITOR C 512 NCB31HK-103X C CAPACITOR C 862 NCB31EK-823X C CAPACITOR C 513 NDC31HJ-331X C CAPACITOR C 901 QEZ0337-228 E CAPACITOR C 514 NCB31EK-104X C CAPACITOR C 902 NCB31HK-103X C CAPACITOR C 515 NCB31EK-103X C CAPACITOR C 903 QEKJ1CM-226Z E CAPACITOR 100MF 20% 10V 1.0MF 20% 50V Area 100MF 20% 10V 10MF 20% 16V 220MF 20% 6.3V 2200MF 22MF 20% 16V 3-7 KD-S621 Electrical parts list (Main board) A Item C 904 3-8 Parts number Parts name Block No. 01 Remarks Area A Item Parts number Parts name QERF1CM-226Z E CAPACITOR 22MF 20% 16V Q 701 DTC114EKA-X C 905 QERF1CM-226Z E CAPACITOR 22MF 20% 16V Q 702 DTC144EKA-X TRANSISTOR C 906 NCB31EK-104X C CAPACITOR Q 731 2SC1623/5-6/-X TRANSISTOR C 907 NCB31HK-103X C CAPACITOR Q 732 2SC1623/5-6/-X TRANSISTOR C 908 QERF1AM-107Z E CAPACITOR 100MF 20% 10V Q 791 2SB1197K/QR/-X TRANSISTOR C 909 QERF1AM-107Z E CAPACITOR 100MF 20% 10V Q 792 2SA812/5-6/-X TRANSISTOR C 910 NCB31HK-103X C CAPACITOR Q 793 DTC114EKA-X TRANSISTOR C 911 QERF1AM-227Z E CAPACITOR Q 861 DTA114EKA-X DIGI TRANSISTOR C 914 NCB31EK-104X C CAPACITOR Q 902 2SC1623/5-6/-X TRANSISTOR C 915 NCB11CK-225X C CAPACITOR Q 903 2SA812/5-6/-X TRANSISTOR C 916 QERF1HM-225Z E CAPACITOR R 101 NRSA63J-471X MG RESISTOR CJ321 QNN0170-001 PIN JACK (REEL) R 102 NRSA63J-752X MG RESISTOR CJ701 QNB0100-002 ANT TERMINAL R 151 NRSA63J-183X MG RESISTOR CN501 QGB2027M1-26S CONNECTOR R 152 NRSA63J-123X MG RESISTOR CN801 VMC0334-001 CONNECTOR R 153 NRSA63J-273X MG RESISTOR CN901 QNZ0002-001 CONNECTOR R 154 NRSA63J-223X MG RESISTOR D 321 1SS254-T2 SI DIODE R 155 NRSA63J-152X MG RESISTOR D 332 1SS355-X DIODE R 156 NRS181J-223X MG RESISTOR D 333 1SS355-X DIODE R 201 NRSA63J-471X MG RESISTOR D 551 DSK10C-T1 DIODE R 202 NRSA63J-752X MG RESISTOR D 701 1SS254-T2 SI DIODE R 251 NRSA63J-183X MG RESISTOR D 702 1SS254-T2 SI DIODE R 252 NRSA63J-123X MG RESISTOR D 731 MTZJ10B-T2 Z DIODE R 253 NRSA63J-273X MG RESISTOR D 791 1SS355-X DIODE R 254 NRSA63J-223X MG RESISTOR D 792 1SS355-X DIODE R 255 NRSA63J-152X MG RESISTOR D 804 1SS254-T2 SI DIODE R 256 NRS181J-223X MG RESISTOR 220MF 20% 10V 2.2MF 20% 50V TRANSISTOR D 810 1SS355-X DIODE R 301 NRSA63J-223X MG RESISTOR D 821 UDZS6.2B-X SI DIODE R 302 NRSA63J-222X MG RESISTOR D 822 UDZS6.2B-X SI DIODE R 303 NRSA63J-473X MG RESISTOR D 823 UDZS6.2B-X SI DIODE R 304 NRSA63J-473X MG RESISTOR D 824 UDZS6.2B-X SI DIODE R 307 NRSA63J-273X MG RESISTOR D 825 UDZS6.2B-X SI DIODE R 308 NRSA63J-273X MG RESISTOR D 826 UDZS6.2B-X SI DIODE R 321 NRS181J-473X MG RESISTOR D 827 UDZS6.2B-X SI DIODE R 322 NRS181J-471X MG RESISTOR D 828 UDZS6.2B-X SI DIODE R 323 NRS181J-102X MG RESISTOR D 861 MTZJ4.7B-T2 Z DIODE R 333 NRSA63J-102X MG RESISTOR D 866 1SS355-X DIODE R 334 NRSA63J-101X MG RESISTOR D 867 1SS355-X DIODE R 336 NRSA63J-222X MG RESISTOR D 868 1SS355-X DIODE R 401 NRSA63J-223X MG RESISTOR D 869 1SS355-X DIODE R 402 NRSA63J-222X MG RESISTOR D 901 1N5401-TU-15 DIODE R 403 NRSA63J-473X MG RESISTOR D 902 SB10-03A3-T2 SB DIODE R 404 NRSA63J-473X MG RESISTOR D 903 1SS254-T2 SI DIODE R 407 NRSA63J-273X MG RESISTOR D 904 CRS03-W SB DIODE R 408 NRSA63J-273X MG RESISTOR IC151 NJM4565M-WE IC R 433 NRSA63J-102X MG RESISTOR IC301 TEA6320T-X IC R 434 NRSA63J-101X MG RESISTOR IC321 LA4743K IC R 436 NRSA63J-222X MG RESISTOR IC501 AN8806SB-W IC R 501 NRS181J-220X MG RESISTOR IC541 LA6567H-X IC R 502 NRS181J-220X MG RESISTOR IC561 MN6627482WA IC R 503 NRS181J-102X MG RESISTOR IC801 LC72366-9A73 IC R 504 NRSA63J-392X MG RESISTOR IC901 HA13164A IC R 505 NRSA63J-224X MG RESISTOR L 501 QQL231K-4R7Y INDUCTOR R 506 NRSA63J-223X MG RESISTOR L 561 QQL231K-4R7Y INDUCTOR R 507 NRSA63J-822X MG RESISTOR L 562 QQL231K-4R7Y INDUCTOR R 508 NRSA63J-104X MG RESISTOR L 701 QQL231K-4R7Y INDUCTOR R 509 NRSA63J-223X MG RESISTOR L 801 QQL231K-4R7Y INDUCTOR R 510 NRSA63J-154X MG RESISTOR L 901 QQR0703-001 CHOKE COIL R 511 NRSA63J-274X MG RESISTOR Q 321 DTC114EKA-X TRANSISTOR R 512 NRSA63J-563X MG RESISTOR Q 332 2SD1781K/QR/-X TRANSISTOR R 513 NRSA63J-563X MG RESISTOR Q 432 2SD1781K/QR/-X TRANSISTOR R 514 NRSA63J-123X MG RESISTOR Q 501 2SA1706/ST/-T TRANSISTOR R 515 NRSA63J-123X MG RESISTOR Q 541 2SA1706/ST/-T TRANSISTOR R 516 NRSA63J-123X MG RESISTOR Remarks Area KD-S621 Electrical parts list (Main board) A Item Parts number Parts name Block No. 01 Remarks Area A Item Parts number Parts name R 517 NRSA63J-123X MG RESISTOR R 814 NRSA63J-473X MG RESISTOR R 518 NRSA63J-822X MG RESISTOR R 815 NRSA63J-473X MG RESISTOR R 519 NRSA63J-105X MG RESISTOR R 816 NRSA63J-473X MG RESISTOR R 541 NRS181J-621X MG RESISTOR R 817 NRS181J-472X MG RESISTOR R 542 NRSA63J-432X MG RESISTOR R 818 NRS181J-473X MG RESISTOR R 543 NRSA63J-303X MG RESISTOR R 822 NRSA63J-222X MG RESISTOR R 544 NRSA63J-332X MG RESISTOR R 823 NRSA63J-473X MG RESISTOR R 545 NRSA63J-123X MG RESISTOR R 825 NRS181J-473X MG RESISTOR R 546 NRSA63J-563X MG RESISTOR R 826 NRSA63J-473X MG RESISTOR R 547 NRSA63J-154X MG RESISTOR R 827 NRSA63J-473X MG RESISTOR R 548 NRSA63J-432X MG RESISTOR R 828 NRSA63J-473X MG RESISTOR R 549 NRSA63J-203X MG RESISTOR R 829 NRS181J-473X MG RESISTOR R 550 NRSA63J-682X MG RESISTOR R 830 NRS181J-223X MG RESISTOR R 551 NRSA63J-822X MG RESISTOR R 831 NRS181J-472X MG RESISTOR R 560 NRS181J-101X MG RESISTOR R 832 NRS181J-223X MG RESISTOR R 561 NRSA63J-102X MG RESISTOR R 833 NRS181J-472X MG RESISTOR R 562 NRSA63J-102X MG RESISTOR R 834 NRS181J-223X MG RESISTOR R 563 NRSA63J-102X MG RESISTOR R 835 NRS181J-472X MG RESISTOR R 564 NRSA63J-102X MG RESISTOR R 836 NRSA63J-473X MG RESISTOR R 567 NRSA63J-102X MG RESISTOR R 840 NRSA63J-473X MG RESISTOR R 568 NRSA63J-102X MG RESISTOR R 841 NRSA63J-473X MG RESISTOR R 569 NRSA63J-102X MG RESISTOR R 842 NRSA63J-473X MG RESISTOR R 570 NRSA63J-102X MG RESISTOR R 843 NRSA63J-0R0X MG RESISTOR R 571 NRS181J-333X MG RESISTOR R 844 NRSA63J-0R0X MG RESISTOR R 573 NRSA63J-333X MG RESISTOR R 845 NRSA63J-0R0X MG RESISTOR R 574 NRSA63J-221X MG RESISTOR R 861 NRS181J-471X MG RESISTOR R 575 NRSA63J-221X MG RESISTOR R 862 NRS181J-471X MG RESISTOR R 576 NRSA63J-0R0X MG RESISTOR R 901 NRSA63J-912X MG RESISTOR R 577 NRSA63J-104X MG RESISTOR R 902 QRZ0125-102X C RESISTOR R 579 NRSA63J-102X MG RESISTOR R 903 NRSA63J-472X MG RESISTOR R 580 NRSA63J-224X MG RESISTOR R 904 NRSA63J-104X MG RESISTOR R 581 NRSA63J-0R0X MG RESISTOR R 905 NRSA63J-472X MG RESISTOR R 701 NRSA63J-102X MG RESISTOR R 906 NRSA63J-472X MG RESISTOR R 702 NRSA63J-151X MG RESISTOR R 907 NRSA63J-393X MG RESISTOR R 703 NRSA63J-102X MG RESISTOR R 908 NRSA63J-683X MG RESISTOR R 704 NRSA63J-151X MG RESISTOR R 909 NRSA63J-273X MG RESISTOR R 705 NRSA63J-103X MG RESISTOR R 910 NRSA63J-473X MG RESISTOR R 708 NRSA63J-822X MG RESISTOR R 911 NRS181J-473X MG RESISTOR R 725 NRSA63J-820X MG RESISTOR TU701 QAU0257-001 TUNER R 731 NRS181J-152X MG RESISTOR X 561 QAX0714-001Z C RESONATOR R 732 NRSA63J-102X MG RESISTOR X 801 QAX0406-001Z CRYSTAL R 733 NRSA63J-103X MG RESISTOR R 734 NRS181J-471X MG RESISTOR R 791 NRSA63J-103X MG RESISTOR R 792 NRSA63J-102X MG RESISTOR R 793 NRSA63J-103X MG RESISTOR R 794 NRSA63J-222X MG RESISTOR R 795 NRS181J-150X MG RESISTOR R 796 NRS181J-150X MG RESISTOR R 797 NRS181J-100X MG RESISTOR R 798 NRSA63J-223X MG RESISTOR R 799 NRSA63J-473X MG RESISTOR R 801 NRS181J-103X MG RESISTOR R 803 NRS181J-332X MG RESISTOR R 804 NRS181J-332X MG RESISTOR R 805 NRS181J-332X MG RESISTOR R 807 NRS181J-473X MG RESISTOR R 808 NRS181J-102X MG RESISTOR R 809 NRS181J-103X MG RESISTOR R 810 NRSA63J-104X MG RESISTOR R 811 NRSA63J-332X MG RESISTOR R 812 NRSA63J-332X MG RESISTOR R 813 NRSA63J-473X MG RESISTOR Remarks Area 1.0K 1W 3-9 KD-S621 Electrical parts list (Front board) A 3-10 Item Parts number C 601 NCB31HK-223X C 602 C 603 Parts name Block No. 02 Remarks Area A Item Parts number Remarks Parts name C CAPACITOR R 651 NRSA63J-222X MG RESISTOR NCS31HJ-681X C CAPACITOR R 652 NRSA63J-222X MG RESISTOR NBE20JM-106X TS E CAP SVB20J R 653 NRSA63J-103X MG RESISTOR CJ601 VMC0335-001 CONNECTOR R 654 NRSA63J-103X MG RESISTOR D 601 LNJ308G81/1-3/X LED VOL+ G LED R 655 NRSA63J-103X MG RESISTOR D 602 LNJ308G81/1-3/X LED VOL- G LED R 656 NRSA63J-103X MG RESISTOR D 603 LNJ308G81/1-3/X LED LOUD G LED R 657 NRSA63J-513X MG RESISTOR D 604 LNJ308G81/1-3/X LED SEL G LED R 658 NRSA63J-184X MG RESISTOR D 605 LNJ308G81/1-3/X LED DISP G LED S 601 NSW0066-001X TACT SWITCH POWER D 606 LNJ308G81/1-3/X LED 1 G LED S 602 NSW0066-001X TACT SWITCH VOL- D 607 LNJ308G81/1-3/X LED 2 G LED S 603 NSW0066-001X TACT SWITCH VOL+ D 608 LNJ308G81/1-3/X LED 3 G LED S 604 NSW0066-001X TACT SWITCH LOUD D 609 LNJ308G81/1-3/X LED 4 G LED S 605 NSW0066-001X TACT SWITCH DISP D 610 LNJ308G81/1-3/X LED 5 G LED S 606 NSW0066-001X TACT SWITCH 1 D 611 LNJ308G81/1-3/X LED 6 G LED S 607 NSW0066-001X TACT SWITCH SELECT D 612 LNJ308G81/1-3/X LED MODE G LED S 608 NSW0066-001X TACT SWITCH 2 D 613 SML-310VT/JK/-X LED SCM R LED S 609 NSW0066-001X TACT SWITCH 3 D 614 LNJ308G81/1-3/X LED EJECT G LED S 610 NSW0066-001X TACT SWITCH 4 D 615 LNJ308G81/1-3/X LED FM G LED S 611 NSW0066-001X TACT SWITCH 5 D 616 LNJ308G81/1-3/X LED CD G LED S 612 NSW0066-001X TACT SWITCH EJECT D 617 LNJ308G81/1-3/X LED AM G LED S 613 NSW0066-001X TACT SWITCH UP D 618 LNJ308G81/1-3/X LED UP G LED S 614 NSW0066-001X TACT SWITCH 6 D 619 LNJ308G81/1-3/X LED DOWN G LED S 615 NSW0066-001X TACT SWITCH MODE D 620 SML-310LT/MN/-X LED POWER R LED S 616 NSW0066-001X TACT SWITCH SCM D 641 UDZS5.1B-X Z DIODE S 617 NSW0066-001X TACT SWITCH DOWN D 642 1SS355-X DIODE S 618 NSW0066-001X TACT SWITCH AM D 643 1SS355-X DIODE S 619 NSW0066-001X TACT SWITCH FM D 645 UDZS6.2B-X SI DIODE S 620 NSW0066-001X TACT SWITCH CD IC601 LC75823W IC PL601 QLL0056-001 PILOT LAMP PL602 QLL0056-001 PILOT LAMP R 601 NRSA63J-681X MG RESISTOR R 602 NRSA63J-561X MG RESISTOR R 603 NRSA63J-681X MG RESISTOR R 604 NRSA63J-911X MG RESISTOR R 605 NRSA63J-122X MG RESISTOR R 606 NRSA02J-681X MG RESISTOR R 607 NRSA02J-561X MG RESISTOR R 608 NRSA02J-681X MG RESISTOR R 609 NRSA02J-911X MG RESISTOR R 610 NRSA63J-122X MG RESISTOR R 611 NRSA63J-152X MG RESISTOR R 612 NRSA63J-681X MG RESISTOR R 613 NRSA63J-561X MG RESISTOR R 614 NRSA63J-681X MG RESISTOR R 615 NRSA63J-911X MG RESISTOR R 616 NRSA63J-122X MG RESISTOR R 617 NRSA63J-152X MG RESISTOR R 631 NRSA02J-821X MG RESISTOR R 632 NRSA02J-821X MG RESISTOR R 633 NRSA02J-821X MG RESISTOR R 634 NRSA02J-511X MG RESISTOR R 635 NRSA02J-511X MG RESISTOR R 636 NRSA02J-152X MG RESISTOR R 637 NRSA02J-152X MG RESISTOR R 638 NRSA02J-221X MG RESISTOR R 639 NRSA02J-221X MG RESISTOR R 640 NRSA02J-221X MG RESISTOR R 641 NRSA02J-221X MG RESISTOR R 642 NRSA02J-511X MG RESISTOR R 643 NRSA02J-511X MG RESISTOR R 644 NRSA02J-821X MG RESISTOR R 645 NRSA02J-821X MG RESISTOR Area KD-S621 Packing materials and accessories parts list Block No. M 3 M M Block No. M 5 M M P1 A1~A5 P8 P7 A6 P6 A13 P5 A15 A14 P8 P2 KIT : A7~A11 P1 A1 P3 P4 A12 3-12 KD-S621 Parts list (Packing) A Item Block No. M3MM Parts number Parts name Description Q'ty P 1 FSPG4002-001 POLY BAG 2 FOR INST BOOK P 2 QPA00801205 POLY BAG 1 FOR SCREW KIT P 3 QPA01003003 POLY BAG 1 FOR HARD CASE P 4 FSYH4036-068 SHEET 1 P 5 QPA01003003 POLY BAG 1 FOR CORD ASSY P 6 QPC03004315P POLY BAG 1 FOR SET P 7 GE30407-017A CARTON 1 P 8 GE10036-001A EPS CUSHION 2 Parts list (Accessories) A Item Area Block No. M5MM Parts number Parts name Description Q'ty Area A 1 GET0066-001A INST BOOK 1 ENG, GER, FRE, DUT A 2 GET0066-002A INST BOOK GET0066-003A INSTALL MANUAL 1 SPA, ITA, SWE, FIN 1 ENG, GER, FRE, DUT E A 3 A 4 GET0066-004A INSTALL MANUAL 1 SPA, ITA, SWE, FIN E A 5 BT-54013-2 W.CARD 1 A 6 LV40978-001A CAUTION SHEET 1 A 7 VKZ4027-202 PLUG NUT 1 A 8 VKH4871-001SS MOUNT BOLT 1 A 9 VKZ4328-001 LOCK NUT 1 A 10 WNS5000Z WASHER 1 A 11 FSKL4010-002 HOOK 2 A 12 FSJB3001-30C HARD CASE 1 A 13 FSKM2004-202 MOUNTING SLEEVE 1 A 14 QAM0089-001 16P CORD ASSY 1 A 15 FSJD2034-001 TRIM PLATE 1 KDGS717K-SCREW1 SCREW PARTS KIT 1 A7~A11 KIT 3-13 KD-S621 VICTOR COMPANY OF JAPAN, LIMITED MOBILE ELECTRONICS DIVISION PERSONAL & MOBILE NETWORK BUSINESS UNIT. 10-1,1Chome,Ohwatari-machi,Maebashi-city,371-8543,Japan 200201 (No.49675) www.s-manuals.com