LT 52246 Lt52246 Manual

User Manual: LT-52246

Open the PDF directly: View PDF .
Page Count: 49

Download
Open PDF In Browser	View PDF

LCD FLAT PANEL HDTV
MODELS

148 Series

LT-40148, LT-46148, LT-52148

246 Series
LT-46246, LT-52246

OWNER’S GUIDE

•

•
•
•

For questions:
-- Visit our website at www.mitsubishi-tv.com.
-- E-mail us at MDEAservice@mdea.com.
-- Call Consumer Relations at 800-332-2119.
For information on System Reset, please see the back cover.
To order replacement or additional remote controls or Owner’s Guides, visit our website at
www.mitsuparts.com or call 800-553-7278.
Guidelines for setting up and using your new widescreen TV start on page 12.

For Your Records
Record the model number, serial number, and
purchase date of your TV. The model and serial
numbers are on the back of the TV. Refer to this
page when requesting assistance with the TV.
MODEL NUMBER
SERIAL NUMBER
PURCHASE DATE
RETAILER NAME
LOCATION

CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead
symbol within an equilateral triangle is
intended to alert the user of the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may
be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the product.

MAINS DISCONNECTION: The mains plug is used
as the disconnect device. The disconnect device shall
remain readily operable.
TV WEIGHT: This TV is heavy! Exercise extreme care
when lifting or moving it. Lift or move the TV with a
minimum of two adults. To prevent damage to the TV,
avoid jarring or moving it while it is turned on. Always
power off your TV, unplug the power cord, and disconnect all cables before moving it.
WARNING: To reduce the risk of fire or electric shock,
do not expose this apparatus to rain or moisture.
WARNING: This product contains chemicals known
to the State of California to cause cancer and/or birth
defects or other reproductive harm.

FCC Declaration of Conformity
Product:

LCD Flat Panel HDTV

Models:

LT-40148, LT-46148, LT-52148
LT-46246, LT-52246

Responsible
Party:

Mitsubishi Digital Electronics
America, Inc.
9351 Jeronimo Road
Irvine, CA 92618-1904

Telephone:

(800) 332-2119

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and
(2) this device must accept any interference
received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio
or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and the receiver.
-- Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/
TV technician for help.
Changes or modifications not expressly
approved by Mitsubishi could cause harmful
interference and would void the user’s authority
to operate this equipment.

Features and specifications described in this owner’s
guide are subject to change without notice.

Contents
Important Information About Your TV
Important Safety Instructions. . . . . . .
Installation and Operating Notes. . . . .
TV Guide Daily Access Requirements.
Cleaning Recommendations. . . . . . . .

. . . . . . . . .
. . . . . . . . .
. . . . . . . . .
. . . . . . . . .

1 Television Overview
Package Contents. . . . . . . . . . . . . . . . . .
Special Features of Your TV. . . . . . . . . . .
TV Control Panel and Convenience Inputs.
TV Main Panel. . . . . . . . . . . . . . . . . . . . .
Stand Removal. . . . . . . . . . . . . . . . . . . .

6
. 6
. 7
. 9
11

. . . . . .
. . . . .
. . . . .
. . . . .
. . . . .

2 TV Setup
Guidelines for Setting Up and Using Your New
Widescreen TV. . . . . . . . . . . . . . . . . . . . . .
Initial TV Setup.. . . . . . . . . . . . . . . . . . . . . . .
Setting Up TV Inputs. . . . . . . . . . . . . . . . . . .
Controlling A/V Receiver Sound Volume.. . . . .
Using the TV with a Personal Computer. . . . . .
Using a CableCARD.. . . . . . . . . . . . . . . . . . .

. .
. .
. .
. .
. .
. .

3 TV Connections
Before You Begin.. . . . . . . . . . . . . . . . . . . . . . .
Cable Management. . . . . . . . . . . . . . . . . . . . . .
HDTV Cable Box or Satellite Receiver, DVD
Player, or Other Device with Component Video. .
HDMI Device (Cable Box, Satellite Receiver, DVD
Player, or Other Device).. . . . . . . . . . . . . . . . . . .
DVI Video Device (Cable Box, Satellite Receiver,
DVD Player, or Other Device).. . . . . . . . . . . . . .
Standard Cable Box, Satellite Receiver, or Other
Device with S-Video. . . . . . . . . . . . . . . . . . . . .
Wall Outlet Cable (no cable box). . . . . . . . . . . . .
Antenna with a Single Lead.. . . . . . . . . . . . . . . .
Antennas with Separate UHF and VHF Leads. . . .
VCR to an Antenna or Wall Outlet Cable.. . . . . . .
VCR to a Cable Box (Audio & Video).. . . . . . . . . .
Older Cable Box.. . . . . . . . . . . . . . . . . . . . . . . .
A/V Receiver (Sound System) Using the TV’s
Audio Output.. . . . . . . . . . . . . . . . . . . . . . . . .
A/V Receiver with HDMI Output. . . . . . . . . . . . .
Camcorder. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio-Only Device. . . . . . . . . . . . . . . . . . . . . . .
4 TV Operation and Features
Choosing a Viewing Source.. .
Sleep Timer.. . . . . . . . . . . . .
Remote Control. . . . . . . . . . .

4
5
5
5

. . . . . . . . . . . . . .
. . . . . . . . . . . . . .
. . . . . . . . . . . . . .

12
14
14
16
18
20

21
21
22
22
23
23
24
24
24
25
25
26
27
27
28
28

29
29
30

ChannelView Channel Listings.. . . . . . . . . . . . . .
Status Display. . . . . . . . . . . . . . . . . . . . . . . . . .
Fav (Favorite Channels).. . . . . . . . . . . . . . . . . . .
TV Signals and Display Formats. . . . . . . . . . . . .
Viewing Camera Files and GalleryPlayer Images. .
5 TV Menus
Main Menu. . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Control Keys for the TV Menu System. .
AV Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Video Menu . . . . . . . . . . . . . . . . . . . . . . .
Audio Menu . . . . . . . . . . . . . . . . . . . . . . .
Captions Menu. . . . . . . . . . . . . . . . . . . . . . . .
Setup Menu.. . . . . . . . . . . . . . . . . . . . . . . . . .
Inputs Menu. . . . . . . . . . . . . . . . . . . . . . . . . .
Lock Menu. . . . . . . . . . . . . . . . . . . . . . . . . . .
Pass Codes.. . . . . . . . . . . . . . . . . . . . . . .
Parent Menu. . . . . . . . . . . . . . . . . . . . . . .
Other Menu (Alternate Rating System). . . . .
Bypassing TV Locks.. . . . . . . . . . . . . . . . .
6 NetCommand IR Control
About NetCommand IR Control.. . . . . . . . . .
IR Emitter Placement. . . . . . . . . . . . . . . . . .
Initial NetCommand Setup for Most Devices..
Adding or Removing Device Keys from
NetCommand Control.. . . . . . . . . . . . . . . .
NetCommand Specialized Device Keys. . . . .
Operating NetCommand-Controlled Devices.
Setting Up NetCommand Control of an
A/V Receiver. . . . . . . . . . . . . . . . . . . . . . .

.
.
.
.
.
.
.
.
.
.
.

. . .
. . .
. . .

37
37
38
40
42
43
44
50
51
51
51
51
51

54
55
56

. . .

56
57
58

. . .

. . .
. . .

Appendices
Appendix A: Specifications. . . . . . . . . . . . . . .
Appendix B: Bypassing the Parental Lock. . . . .
Appendix C: Programming the Remote Control.
Appendix D: TV Guide Daily (246 Series TVs).. .
Appendix E: NetCommand HDMI Control of
CEC Devices. . . . . . . . . . . . . . . . . . . . . . . . .
Appendix F: Troubleshooting. . . . . . . . . . . . . .

.
.
.
.

66
67
69
76

80
83

. . . . . . . . .

. . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Trademark and License Information. .
Mitsubishi TV Software.
Warranty.
Index. .

.
.

31
32
33
34
35

Important Safety Instructions
Please read the following safeguards for your TV and
retain for future reference. Always follow all warnings
and instructions marked on the television.
1)

Read these instructions.

2) Keep these instructions.
3) Heed all warnings.
4)

Follow all instructions.

5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7)

Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.

10) Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart,
stand, tripod, bracket,
or table specified
by the manufacturer,
or sold with the
apparatus. When
a cart is used, use
caution when moving
the cart/apparatus
combination to avoid
injury from tip-over.

Installation Notes

Cleaning Recommendations

Wall Mount Requirements
For wall-mounting, see “Stand Removal,” page 11.

Normally, light dusting with a dry, non-scratching duster
will keep your TV clean. If cleaning beyond this is
needed, please use the following guidelines:

Use with other than the authorized accessories
may cause the TV to become unstable, which can
cause damage to the product or possible injury.
Custom cabinet installation must allow for proper
air circulation around the television.
NOTE TO CATV SYSTEM INSTALLER: THIS REMINDER
IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER’S
ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR THE PROPER GROUNDING AND,
IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND
SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF
THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY
AS PRACTICAL.

Crystalline liquid may leak from the LCD panel and
broken glass may be scattered.

14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.

CAUTION: The crystalline liquid is toxic. Avoid
contact with your skin, eyes, or mouth. DO NOT
touch the broken glass or crystalline liquid. DO NOT
get glass fragments or crystalline liquid into eyes or
mouth. Should either contact with your eyes or
mouth, rinse the contacted area thoroughly with
water and consult your doctor.

Disposal of Your TV

If an outside antenna or cable system is connected
to the TV, be sure the antenna or cable system is
grounded so as to provide some protection against
voltage surges and built-up static charges.

Replacement Parts
When replacement parts are required, be sure the
service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock or other hazards.

%8!-0,% /& !.4%..! '2/5.$).'

!.4%..!
,%!$ ). 7)2%
'2/5.$ #,!-0

%,%#42)#
3%26)#%
%15)0-%.4

!.4%..!
$)3#(!2'% 5.)4
.%# !24)#,%
'2/5.$).'
#/.$5#4/23
.%# !24)#,%
'2/5.$ #,!-03

.%# .!4)/.!, %,%#42)#!, #/$%

Top and Sides of the TV
•

Occasionally clean dust build-up from the air-intake
grilles on the back and sides of the TV. Clean using
a vacuum cleaner with a brush attachment.
Gently wipe down your TV with a soft, non-abrasive
cloth such as cotton flannel or a clean cloth diaper,
lightly moistened with water. Dry with a second dry,
soft, non-abrasive cloth.
For oily dirt, add a few drops of mild liquid detergent, such as dishwashing detergent, to the water
used to moisten the cloth. Rinse with a second
cloth moistened only with water. Dry with a third
dry, soft, non-abrasive cloth.
Glossy Surfaces: Take special care when cleaning
the TV’s glossy surfaces.
-- Always shake or brush the cleaning cloth first to
remove any dirt particles.
-- Wipe the glossy areas gently, without applying
pressure.
-- If necessary, lightly dampen the cloth with
water. Use no chemical or abrasive cleaners.

•

If Your TV Gets Damaged

13) Unplug this apparatus during lightning storms or
when unused for long periods of time.

Outdoor Antenna Grounding

First, turn off the TV and unplug the power cord from
the power outlet.

0/7%2 3%26)#% '2/5.$).'
%,%#42/$% 3934%.%# !24 0!24 (

•

LCD Screen Cleaning

The LCD panel contains a small amount of crystalline
liquid and the fluorescent tube in the panel contains
mercury. Both are toxic and should not be touched.
DO NOT dispose of the TV with general household
waste. THE LAMPS INSIDE THIS PRODUCT CONTAIN
MERCURY AND MUST BE RECYCLED OR DISPOSED
OF ACCORDING TO LOCAL, STATE, AND FEDERAL
LAWS. For disposal or recycling information, contact
your local authorities or the Electronic Industries Alliance at www.eiae.org.

TV Software

Do not attempt to update the software of this TV with
software or USB drives not provided by or authorized by
Mitsubishi Digital Electronics America, Inc. Non-authorized
software may damage the TV and will not be covered by
the warranty.

TV Guide Daily Access Requirements

TV Guide Daily listings are not provided by Mitsubishi Digital
Electronics America, Inc. Operation of TV Guide Daily
requires over-the-air or direct cable (no cable box) access to
stations carrying TV Guide Daily program listings. If listings
are not available in your area or become discontinued by the
local provider, TV Guide Daily will not operate. TV Guide Daily
does not provide program listings for satellite TV systems.

IMPORTANT
DO NOT apply any type of liquid to the surface of
the TV screen.

•
•
•

Use only use a soft, dry cloth to clean the LCD
screen. Do not use any liquids.
Wipe the screen gently with an up and down
motion.
Clean the entire screen evenly, not just sections of
the screen.

General Cleaning Precautions
•
•
•

•
•

DO NOT allow liquid to enter the TV through the
ventilation slots or any crevice.
DO NOT use any strong or abrasive cleaners, as
these can scratch the surfaces.
DO NOT use any cleaners containing ammonia,
bleach, alcohol, benzene, or thinners, as these can
dull the surfaces.
DO NOT spray liquids or cleaners directly on the
TV’s surfaces.
DO NOT scrub or rub the TV harshly. Wipe it gently.

Television Overview

DVD players, cable boxes, and satellite receivers. NetCommand can “learn” remote control signals directly
from many devices, allowing you to create a customized NetCommand-controlled home-theater system.

POWER SYSTEM
RESET

VOL

ADJ

FORMAT MENU GUIDE INPUT
ENTER

CANCEL

NetCommand for HDMI

Package Contents

16:9 Widescreen Picture Format

Please take a moment to review the following list of
items to ensure that you have received everything.
1.
2.
3.
4.
5.
6.
7.
8.

1. Television Overview

Remote Control
Two AA Batteries
Cable Tie with Pin
Owner’s Guide
Quick Reference Guide
Quick Connect Guide
Product Registration Card
IR Emitter cable (two-ended with 148 series;
four-ended with 246 series)
1

AA
AA

Enjoy a full theatrical experience in the comfort of your
home. View pictures as film directors intended them.
Digital TV broadcasts, DVDs and newer video game
consoles support this widescreen format.

Integrated HDTV Tuner
Your widescreen Mitsubishi HDTV has an internal HDTV
tuner able to receive both over-the-air HDTV broadcasts (received via an antenna) and non-scrambled
digital cable broadcasts, including non-scrambled
HDTV cable programming.

High-Definition Video Inputs
•

8
•

Special Features of Your TV
Your new high-definition widescreen television has
many special features that make it the perfect center of
your home entertainment system, including:

1080p High-Definition LCD Display System
Your Mitsubishi LCD Flat Panel HDTV uses a full 1920
x 1080 LCD panel to create the picture you see on the
screen. All images are displayed at 1080p. The TV
uses Plush 1080p™ to convert lower-resolution signals
to 1080p for display.

Smooth120Hz™ Film Motion
Smooth120Hz™ Film Motion makes fast-moving images
appear smoother and more fluid, free from motion
blur. In this LCD Flat Panel HDTV, Smooth120Hz™
Film Motion doubles the traditional progressive scan
frame rate and creates new frames of video between
the traditional frames to smooth moving images.
Smooth120Hz™ Film Motion also smooths film judder
(image vibration) that may be present in film-based
content such as movies.

Component Video Inputs. Also called Y/Pb/Pr
inputs, these inputs receive standard analog video
formats of 480i, 480p, 720p, and 1080i high-definition signals. This provides a high level of flexibility
when connecting DVD players/recorders, cable
boxes, and satellite receivers.
HDMI Inputs. These inputs accept digital 480i,
480p, 720p, 1080i, and 1080p video signals plus
PCM digital stereo signals. The HDMI™ inputs can
also accept a variety of PC signals and resolutions.
These inputs support HDMI 1.3 Deep Color (up to
36 bits) and the x.v.Color extended color gamut.
Used with an adapter, these inputs also accept
compatible digital DVI video signals. HDMI
inputs provide additional high-performance,
high-definition connections for maximum flexibility
in your choice of home theater products. The HDMI
inputs are HDCP copy-protection compatible.

Easy Connect Auto Input Sensing
Easy Connect™ Auto Input Sensing automatically recognizes when you plug in an input and prompts you to
assign a name to it. The TV ignores any unused inputs,
so the result is an uncluttered Input Selection menu
where you can easily find and select connected devices
by name.

Home Theater Control
NetCommand with IR Learning
Your Mitsubishi HDTV offers a new level of networking
that seamlessly integrates selected older A/V products
with new and future digital products. NetCommand®
supports IR (infrared) control of products such as VCRs,

HDMI devices with Consumer Electronics Control (CEC)
capabilities may be compatible with the TV’s NetCommand for HDMI feature. Compatible devices can
receive control signals through the HDMI connection.

SYSTEM
RESET

GalleryPlayer
GalleryPlayer allows you to transform your TV into
an art showcase. Beautiful high-definition images
to display on your TV are available for purchase at
Mitsubishi.GalleryPlayer.com. Several sample images
are provided with the TV. See page 49.

TV Guide Daily Interactive
Program Guide System
246 Series TVs. The TV Guide Daily system is an
on-screen program guide for cable and over-the-air
reception. This subscription-free guide system lists
regular, digital, and high-definition programming. Note
that when the system is first set up, it may take up to 24
hours to begin receiving TV program listings.

If the TV fails to respond to the remote control, control-panel buttons, or will not power on/off, press the
SYSTEM RESET button on the control panel.
The LED on the front panel will flash quickly for about
one minute. When the LED stops flashing, you may turn
on the TV. Recent setting changes you made before
using SYSTEM RESET may be lost.

Convenience Inputs
•

Swivelling Stand
The included stand
allows the TV to be swiveled manually up to 30
degrees left or right to the
best viewing angle.

System Reset Button

Top View

•

30°

INPUT 4 is a readily accessible set of input jacks for
a camcorder, game, or other audio/video device.
A USB photo port lets you view JPEG images from
a USB drive or card reader.

30°
Front
INPUT 4

The TV can be swiveled
up to 30 degrees left or
right.

TV Control Panel and
Convenience Inputs

Control Panel
Buttons on the control panel duplicate commonly used
keys on the remote control. The upper labels show
control functions when no TV menus are displayed; the
lower labels indicate functions when TV menus are displayed or when a special function has been activated.
See “Remote Control,” page 30, for a full description of
the functions of these buttons.
A/V Reset
If you wish to reset the A/V (Audio/Video) settings back
to the factory defaults:
• To reset all settings at once, press GUIDE and FORMAT
on the control panel at the same time.
• To reset the defaults for individual inputs, use the
Reset selection on the AV menu. See “AV Menu,”
page 38.

Y/
VIDEO

Note:
To connect a standard video
device (composite video):
connect the single (yellow)
video cable to the Y/VIDEO
jack.

AUDIO

USB

1. Television Overview

Front-Panel Indicators
•
•

•

1. Television Overview

STATUS

POWER

STATUS indicator. Off during normal TV
operation.
POWER/TIMER indicator. Lit when TV is
powered on; flashes when TV is powered
off and the auto-on TV Timer is set.
IR Sensor (Infrared Sensor). Detects infrared signals emitted by the remote control.

IR Sensor

TV Main Panel
1. ANT 1/ANT 2 (Antenna)
If you are connecting an antenna or direct cable service
without a cable box, connect the main antenna or cable
source to ANT 1. Use ANT 2 for a second source.

HDMI

POWER

VIDEO: 480i,
480p /720p
1080i /1080p
AUDIO:
PCM STEREO

STATUS
IR Sensor

ANT 1 and ANT 2 can each receive digital and analog
over-the-air channels from a VHF/UHF antenna or nonscrambled digital/analog cable source.

PC: VGA,
W-VGA, SVGA,
W-SVGA, XGA,
W-XGA, SXGA /
3
720p/1080p

148 Series TVs

246 Series TVs

Off

Steady On

Slow Blinking

Fast Blinking

POWER Indicator
LED Color TV Condition
Standby condition.

Normal operation.

Green

TV is powered on.

Normal operation.

Green

TV powered off, auto-on timer is set. Normal operation. TV can be turned on at any time.

Green

Wait approximately one minute for blinking to stop before turning
on. Normal operation.

Y Pb Pr Component Video (480i/480p/720p/1080i)
Use these jacks to connect devices with component video
outputs, such as DVD players, external HDTV receivers, or compatible video game systems. Use the adjacent AUDIO R and L
jacks for INPUT 1 or INPUT 2 if you wish to send audio to the TV.
See Appendix A specifications for signal compatibility.

IR- NetCommand

S-VIDEO

Output / External
Controller Input

2. AC just restored after power failure.

3. TV rebooting after System Reset
used.

Pr
VIDEO

5. You have begun the procedure
to update software from an
authorized flash memory device.

AUDIO
R
Y

DVI/PC

STATUS Indicator
LED Color TV Condition

(480i / 480p / 720p / 1080i)

INPUT3

4. TV rebooting after power fluctuation or receiving abnormal
digital signals from a digital
channel or digital device.

Additional Information

None

Normal TV on or standby condition.

Normal operation.

Red

TV may require service.

Turn off the TV and unplug the set from the AC power source.
Wait one minute and then plug the set back in. See Appendix F.
If the LED is still on, contact your dealer or a Mitsubishi
Authorized Service Center. Go to www.mitsubishi-tv.com or call
1-800-332-2119 to receive Authorized Service Center information.

2
5

AUDIO

R
INPUT2

INPUT1

DIGITAL
AUDIO
OUTPUT

3. AUDIO L and R (INPUT 1, INPUT 2)
Analog stereo inputs shared by more than one video input.
• INPUT 1 audio jacks are for use with INPUT 1 component
video (Y Pb Pr) or composite video (single yellow cable).
• INPUT 2 audio jacks are for use with INPUT 2 component
video exclusively.

4. S-VIDEO (INPUT 3)

Y / VIDEO

ANT 1/MAIN and CableCARD™
Use ANT 1/MAIN to receive premium subscription
cable TV service authorized by the CableCARD™ access card.
The CableCARD access card is provided by your local cable
company.

2. Component Video (INPUT 1, INPUT 2)

Additional Information

None

TV just plugged into AC outlet.

Connect an S-Video device to this input. Use the AUDIO R and L
jacks for INPUT 3 (item 6) if you wish to send audio to the TV.

5. Composite Video (INPUT 1, INPUT 3)
Use the VIDEO jacks to connect a VCR, Super VHS (S-VHS)
VCR, DVD player, standard satellite receiver, or other A/V device
to the TV. Use the adjacent AUDIO R and L inputs for INPUT 1 or
INPUT 3 if you wish to send audio to the TV. Note that the INPUT
3 composite video jack is automatically disabled when you
connect to S-VIDEO.

AVR AUDIO
OUTPUT

10
1
ANT2/AUX
RS-232C jack
offered on 246
Series TVs.

ANT1/MAIN

Subwoofer output
offered on 246
Series TVs.

6. AUDIO L and R (INPUT 3)
Analog stereo inputs shared by INPUT 3 composite
video and S-Video.

7. DVI/PC INPUT AUDIO
Use the DVI/PC INPUT AUDIO jack when connecting
a DVI device to one of the TV’s HDMI inputs using a
DVI-to-HDMI cable. These jacks allow you to send
left and right analog audio from your computer or
other DVI device to the TV.

1. Television Overview

TV Main Panel, continued
8. HDMI™ Inputs (High-Definition
Multimedia Interface)
The HDMI inputs support uncompressed standard and highdefinition digital video formats and PCM digital stereo audio.
Use the HDMI inputs to connect to CEA-861 HDMI compliant devices such as a high-definition receiver or DVD player.
These inputs support 480i, 480p, 720p, 1080i, and 1080p
video formats.
Mitsubishi recommends you use category 2 HDMI cables,
also called high-speed HDMI cables, to connect HDMI 1.3
source devices. High-speed category 2 cables bring you
the full benefits of Deep Color and x.v.Color.
These HDMI inputs can also accept digital DVI video signals.
To connect a DVI input, use an HDMI-to-DVI adapter or
cable plus analog audio cables. Connect the analog audio
cables to the DVI/PC INPUT AUDIO jacks on the TV to
receive left and right stereo audio from your DVI device.
The TV’s HDMI inputs are compatible with many DVI-D and
HDMI computer video signals. For additional information on
PC compatibility, see “Using the TV with a Personal Computer,” page 18, and Appendix A, “Specifications,” page 66.
These inputs are HDCP (High-Bandwidth Digital Copy Protection) compliant.
These inputs are
certified for proper interoperability with other products certified by Simplay™.

9. AVR AUDIO OUTPUT
Use AVR AUDIO OUTPUT to send analog audio of the
program currently shown on the screen to an analog A/V
surround sound receiver or stereo system. Digital audio
from digital channels and HDMI devices is converted to
analog audio by the TV. This is the only audio connection needed between it and the TV if using an analog A/V
receiver or stereo system.
IMPORTANT
Selecting Audio Output Type, 246 Series TVs
The red audio jack can output either right stereo
audio for an A/V receiver or mono bass audio
for a subwoofer. Select the output type when
prompted in the Auto Output Sensing screen.

10. SUBWOOFER OUTPUT
246 Series TVs. Connect a powered subwoofer to the
SUBWOOFER OUTPUT jack. Select Subwoofer when the
Auto Output Sensing screen displays.

11. DIGITAL AUDIO OUTPUT
This output sends Dolby Digital or PCM digital audio to
your digital A/V surround sound receiver. Analog audio
from analog channels and devices is converted by the TV
to PCM digital audio. If you have a digital A/V receiver,

1. Television Overview

Stand Removal
HDMI Cable Categories
HDMI cables are available as Category 1 and Category 2
types.
• Category 2 Cables (also called high-speed HDMI
cables). Newer, HDMI 1.3-compliant DVD players,
video games, and set-top boxes require Category 2
cables, suitable for clock frequencies up to 340 MHz
or data rates of up to 10.2 gigabits per second. Use
category 2 cables for high-speed 1080p HD signals
carrying extended color encodings (i.e., 30 or more
bits, also called Deep Color). Category 2 cables are
also suitable for standard HDTV signals.
• Category 1 Cables (also called standard HDMI
cables). Category 1 cables may be unmarked. They
are suitable for standard HDTV 720p and 1080i
signals with 8-bit color depth. Use category 1 cables
for clock frequencies up to 74.25 MHz or data rates
of up to 2.23 gigabits per second.

CAUTION
At least TWO PEOPLE are needed to safely remove the stand. Have one person hold the TV while the other
person removes the stand. Failure to follow these recommendations may result in personal injury and
damage to the product.

Stand-Removal Procedure:

1. Disconnect the TV’s AC power cord from the AC
2.

in most cases this is the only audio connection needed
between the TV and your A/V receiver.

12. IR NetCommand Output/External
Controller Input
IR emitters connected to this jack are used by the TV’s
NetCommand system to send control signals to external IR
remote-controlled devices such as cable boxes, VCRs, DVD
players, satellite receivers and audio receivers.
When NetCommand is not in use, this jack can be switched
to receive wired IR control signals from external system controllers. To switch this jack to an input, connect the external
controller’s IR output to this jack, then:
1. Press MENU to display the TV menu.
2. Enter the number sequence 2, 4, 7, 0 to display the
Installer menu.
3. Highlight the WIRED IR selection and press ENTER to
change the setting from OFF to ON.
To revert to NetCommand control:
1. Disconnect the IR device.
2. Press MENU to display the TV menu.
3. Enter the number sequence 2, 4, 7, 0 to display the
Installer menu.
4. Highlight the WIRED IR selection and press ENTER to
change the setting from ON to OFF.
Note: When the WIRED IR option is set to ON (control
by an external device), the Low Power setting for
Energy Mode is unavailable.

13. RS-232C
Use the RS-232C interface to receive control signals from
compatible home-theater control devices.

power outlet.
Spread the protective sheet that was wrapped
around the TV on a flat, even surface, such as a
sturdy table. The protective sheet will help prevent
damage to the display.
IMPORTANT: To avoid damaging the screen,
make sure there are no foreign objects under or
on top of the protective sheet.
Position one person on each side of the TV (left and
right sides). Have each person firmly grasp their
side of the TV and gently place it face down on the
protective sheet with the display stand hanging over
the edge of the table. See the illustration to the
right.
Use a magnetic philips screwdriver to remove the
four stand screws from the recessed holes (see
illustration to right). Note: A regular screwdriver
can be used with a separate magnetic pick-up tool.
While one person holds the TV with both hands,
have the other person grasp the plastic portion of
the stand (see illustration to the right) and remove
the stand by pulling it away from the TV in the direction of the large arrow shown in both illustrations.
The TV is now ready for wall mounting. See “Wall
Mount Kit” below.

Wall Mounting Kit (purchased separately)
To order a Wall Mounting Kit, please contact Peerless
Industries, Inc. at (800) 473-3753 or visit www.peerlessmounts.com. Use wall mounting kit Model ST650.
Note: Complete instructions are included with the kit.
To order a Wall Mounting Kit from Mitsubishi Digital
Electronics America, Inc., please visit
www.mitsuparts.com or call (800) 553-7278.

1SPUFDUJWF
TIFFU

4UBOE

5BCMF

TV Back
Cover

Protective Sheet

CAUTION: Using this TV with other than the authorized accessories may cause the TV to become
unstable, which can cause damage to the product
or possible injury.

2. TV Setup

TV Set-Up

Guidelines for Setting Up and Using Your New Widescreen TV
Getting Started
1. Review the important safety, installation, and operating information at the beginning of this book.
2. Choose a location for your TV.
• Allow at least four inches of space on all sides
of the TV to help prevent overheating. Overheating may cause premature failure of the TV.
• Avoid locations where light may reflect off the
screen or where the TV is exposed to direct
sunlight.
• Refer also to “Installation Notes,” page 5.
3. Install the batteries in the remote control. See this
page for instructions. See page 30 for more on use
of the remote control.
4. Plug your TV into a power outlet. The green LED on
the front of the TV will start blinking rapidly. After
the green LED stops blinking, press the POWER key to
power on the TV.
5. When the Welcome screen appears the first time
you power on the TV, select a language for TV
menus. You can later change the language through
the Setup menu.
6. Connect your audio/video (A/V) devices to the TV
and perform initial setup.
• See chapter 3, “TV Connections,” for connection diagrams.
• See the following pages for initial TV setup and
use of the Auto Input Sensing feature.
• To connect the TV to a personal computer, see
“Using the TV with a Personal Computer,” page
18.
• See chapter 6, “NetCommand IR Control,” to
perform NetCommand IR “learning” to set up
control of your home theater.
• To set up NetCommand HDMI control of CECenabled devices, see Appendix E.
7. Mitsubishi recommends you perform a channel
scan for channels received on ANT 1 and ANT 2.
See “Initial TV Setup” page 14.
8. You can now start watching TV or you can perform
additional setup and customization through the TV
menus.

Turning the TV On or Off
To turn the TV on or off, point the remote control at the
front of the TV and press the POWER button. Alternatively, press the POWER button on the TV’s control panel.

Installing the Remote Control
Batteries
1. Remove the remote control’s back cover by
2.
3.

gently pressing in the tab and lifting off the
cover.
Load the batteries, making sure the polarities
(+) and (-) are correct. For best results, insert
the negative (-) end first.
Snap the cover back in place.

The remote
control requires
two AA alkaline
batteries.

When You First Power On the TV
Choosing a Language for Menus
1. Power on the TV for the first time.
2. Press
to select either English or Spanish
for all menus. You can later change the language selection through the Setup > Language menu. See page 44.

Additional TV Setup

TV Operation

1. Review chapter 5, “TV Menus,” to customize TV
operation. Press the MENU key to enter the menu
system. Some examples of settings you may wish
to change include:
• Fav. Use an on-screen menu to create custom
lists of your favorite channels from ANT 1 and
ANT 2. See Setup > Edit, page 45.
• Order. Rearrange the device icons in the Input
Selection menu to put frequently used icons
near the front. See Inputs > Order, page 50.
• Name. Change the device types that appear
in the Input Selection menu. See Inputs >
Name options, page 50.
• Parental Locks. Restrict TV viewing by
program rating, by channel, or by time of day.
You can also disable the control-panel buttons
if you have small children.
-- To restrict TV use by program rating, see
the Lock > Parent menu, page 52.
-- To lock the control-panel buttons, use the
Lock > Control Panel menu, page 53.
-- To restrict TV use by channel, see Setup >
Edit > Lock, page 45.
• Video Settings. Change video adjustments to
get the best picture for your viewing conditions.
See “AV Menu,” page 38.

1. Review chapter 4, “TV Operation and Features,” for
TV features including:
• Input Selection (viewing source). Select a
connected program source to watch, such as a
VCR, DVD player, or antenna. Press INPUT on the
remote control to select from icons for the TV
inputs. See “Choosing a Viewing Source,” page
29.
• Listings. Press GUIDE.
-- For ChannelView™ display of listings
on ANT 1 and ANT 2, see “ChannelView
Channel Listings,” page 31.
-- 246 Series TV. If you have set up and
activated the TV Guide Daily system, press
the GUIDE key to display listings using TV
Guide Daily. See Appendix D,
• Picture Formats. Press FORMAT to cycle through
picture sizes and shapes to find the one best
suited to the current program. See “TV Signals
and Display Formats,” page 34.
2. To view still and moving digital camera images on
the TV, see page 35, “Viewing Camera Files and
GalleryPlayer Images.”
3. To control A/V devices with NetCommand, see
page 58, “Operating NetCommand-Controlled
Devices.”

Note:

TV Cleaning

You may wish to change the Picture Mode from
the default Brilliant to either Bright or Natural,
which are suitable for most home viewing.
2. To see a demo of beautiful images in high-definition
from the Mitsubishi.GalleryPlayer.com collection,
see page 49.
3. To program the remote control to operate A/V
devices not under NetCommand control, see
Appendix C, “Programming the Remote Control.”
4. 246 Series TV. To set up the TV Guide Daily
system, see Appendix D.

See “Cleaning Recommendations,” page 5.

Assistance
•
•

For troubleshooting, service, and product
support, see Appendix F.
For warranty information, see the TV warranty
on page 92.

2. TV Setup

Initial TV Setup
Use the Setup menu for basic TV setup options.
1. Press MENU to open the Main menu.
2. Press to highlight the Setup icon and display the
Setup menu.

Memorizing Channels
For ANT 1 and ANT 2
Note:

246 Series TV. If using a CableCARD, the
TV will automatically acquire the complete list
of available channels from the service provider. Perform channel memorization for ANT 1
CableCARD service only if you need to reacquire
the channel list.

To start channel memorization
1. Connect the incoming cable to ANT 1 or ANT 2.
This is the cable from an antenna or a cable service
without a cable box.
2. With the Setup menu displayed, press to highlight the Scan icon.

2. TV Setup
•

Use the Setup > Edit menu (page 45) for additional
channel options, such as adding or deleting channels from memory, naming channels, and saving
favorite channels in custom memory banks.

See chapter 5, “TV Menu Settings,” to:
• Set the TV clock (page 46)
• Set the TV Timer (page 47) to have the TV power on
at a preset time.
• Select an Energy Mode to manage power use while
the TV is off (page 48).

Setting Up TV Inputs

3. Press

to highlight an input selection based on
your connections:

Input

Condition

Ant 1 Air
Ant 2 Air

When connected to an indoor or
outdoor antenna

Ant 1 Cable
Ant 2 Cable

When connected to direct cable (no
cable box)

4. Press to highlight the on-screen START button.
5. Press ENTER to start automatic channel memoriza-

tion.
To stop channel memorization before
completion, press CANCEL.
When memorization is complete you can:
• Press MENU once to return to the top row of icons.
• Press MENU again to return to the Main menu.
• Press EXIT to watch TV.

After channels have been memorized:
• To tune to memorized channels, press CH
/
while watching TV on the ANT 1 or ANT 2 input.

Auto Input Sensing for CEC-Enabled Devices
When the TV’s NetCommand for HDMI feature is
enabled, most CEC-enabled devices are recognized
and identified automatically by the TV. NetCommand
for HDMI may allow you to control functions of a CECenabled device. See Appendix E, page 80.
Setup Procedure

1. Power on the TV.
2. Connect your devices to the TV, making note

of which TV input is used for each device. See
chapter 3, “TV Connections.”

When You First Connect a Device
The TV’s Easy Connect™ Auto Input Sensing feature
detects most connections automatically.
Note:

Note:

If you wish to use an HDMI device’s CEC capabilities, follow the steps in Appendix E.

For connection and setup of a personal computer, see the information on page 18.

Auto Input Sensing for Most Devices
When you first connect a device, the TV will:
a. Detect the connection and automatically switch
to the input
b. Prompt you to identify the device type (if not
recognized automatically)
c. Prompt you to perform NetCommand set-up for
the device, if available
d. Repeat these steps for any additional newly
detected devices

Start channel memorization from the Setup menu.

Setting Up TV Inputs, continued

See below for connections which trigger Auto Input Sensing.
Auto Input Sensing Available

First select a
device type.
Sample Auto Input Sensing screen.

S-VIDEO
HDMI

USB (USB photo port)
INPUT 4 AUDIO (with video plug, see page 28.
Auto Output Sensing Available

Important Note for NetCommand IR Users
Be sure to select the correct device type here.
Although you can change the device type later in the
Inputs > Name menu, any “learned” NetCommand
IR codes will be erased when you make the change.

4. You can perform NetCommand IR “learning” after

AVR AUDIO OUTPUT (red jack)

No Auto Sensing
ANT 1 and ANT 2

If the device is powered off when connected, detection occurs when the device is next powered on.

See below for how different connections are handled
by Auto Input/Auto Output Sensing.
• Most Device Types. Select the device type
from the on-screen list. The device type you select
here will appear as an icon in the Input Selection
menu.
Press
to move through the device list to highlight
the device type connected to the input. Some device
types also display a sub-menu of names—useful
if using more than one of the same device. See
the sample Auto Input Sensing screen shown.
• A/V Receiver
-- The TV detects audio connections on the
DIGITAL AUDIO OUTPUT jack and the right (red)
AVR AUDIO OUTPUT jack.
-- 246 Series TVs. If using an analog A/V
receiver, highlight AV Receiver when the
Auto Output Sensing screen displays. This
setting causes the TV to pass the full range
of stereo sound to the A/V receiver.
-- For an HDMI connection, select AVR from
the list of device types if the A/V receiver is
not recognized automatically.
• Subwoofer (246 Series TVs). With the subwoofer connected to the right (red) AVR AUDIO
OUTPUT jack, highlight Subwoofer when the
Auto Output Sensing screen displays. With this
setting, a limited range of bass frequencies is
passed to the subwoofer.

Sensing screen for the connection type will display.
Select the device type if required.

Digital Audio OUTPUT (orange jack)
AVR AUDIO OUTPUT/
SUBWOOFER OUTPUT (red jack, 246 Series TVs)

Auto Input/Auto Output Sensing Screens

3. When the TV detects a new connection, the Auto

Y/VIDEO (detected as composite video)
Y/VIDEO plus Pb (detected as component video)

Next perform
IR “learning” if
available.

selecting the device type or at a later time when
convenient. To perform now, highlight the Learn
icon and press ENTER. See “Initial NetCommand
Setup for Most Devices,” page 56 or “Setting Up
NetCommand Control of an A/V Receiver,” page 60.
Press EXIT to close the Auto Sensing screen. The
TV will then display the Auto Sensing screen for
the next connection it finds.
After completing Auto Input/Auto Output Sensing,
you may wish to set up or change control of your
equipment using one of the home-theater control
methods described in this Owner’s Guide. See
“About Home-Theater Control Systems” on page 17.

Auto Output Sensing screen choices for analog audio
•

HDMI Devices Compatible with the TV’s
NetCommand for HDMI Feature. Compatible
CEC-enabled HDMI devices are often recognized
automatically by the TV. After connecting the
device, you may briefly see the standard Auto
Input Sensing screen before the TV recognizes
the device type. See Appendix E.

2. TV Setup

Controlling A/V Receiver Sound Volume

Setting Up TV Inputs, continued
Tips on Auto Sensing and Changing
Connected Devices
•
•
•

Choose a different name for each input.
Antenna inputs (ANT 1/ANT 2) are never detected,
although you can turn off unused antenna inputs in the
Inputs > Name menu.
You can change the device type displayed in the Input
Selection menu by using the Inputs > Name menu (page
50). Any “learned” NetCommand IR codes will be erased,
however.

This summary offers some examples of the control methods available using the TV’s remote control. You may
wish to use one or more of these methods in your home theater after completing Auto Input Sensing.

With a Standard TV Setup

Source device connected directly to the TV

•

Recommended Method: Program the TV’s
remote control for your A/V receiver and enable the
Audio Lock feature. See page 70.
Program the TV’s remote control for your A/V
receiver and set the TV remote’s slide switch to the
AUDIO position to control A/V receiver volume. Set
the switch back to the TV position to control the TV.
Use the remote control that came with the A/V
receiver.

•

1. Disconnect the HDMI device.
2. Delete the HDMI input in the Inputs > Name menu.

With NetCommand IR Control

Disconnecting an Analog A/V Receiver
When you disconnect an analog A/V receiver, be sure
to change the Speakers setting to TV to:
• Hear sound from the TV speakers.
• Redisplay the Auto Output Sensing screen when
you reconnect a device to the AVR AUDIO OUTPUT.

About Home-Theater Control Systems

Use one of the methods below to control sound volume from
the A/V receiver.

Changing Devices on an HDMI Input

See page 50.
Connect the new device and the Auto Input
Sensing screen will display. If you want the device
under NetCommand IR control, perform NetCommand “learning” for the new device.

Set up NetCommand control of the A/V receiver’s
volume functions in the Inputs > AVR menu. The TV’s
remote will then control A/V receiver volume. See page
60.

With NetCommand for HDMI (CEC-Enabled
HDMI A/V Receiver)
The TV’s remote control may control some functions
of the A/V receiver. See “About Home-Theater Control
Systems,” page 17 and Appendix E, page 80.

Remote Control Programming with Any Connection Type
Program the remote control to operate the A/V device. To control the device, set
the slide switch to the correct position for the device type. See Appendix C, “Programming the Remote Control.” In the case of an A/V receiver, use the Audio Lock
feature, page 70.
NetCommand Control with Any Connection Type
Set up NetCommand IR control of the device’s keys as desired. See “IR Emitter
Placement,” page 55, and “Initial NetCommand Setup for Most Devices,” page 56.
CEC-Enabled HDMI Device with HDMI Connection Only
1. Turn on the TV’s NetCommand for HDMI feature. See the instructions in Appendix E, “NetCommand HDMI Control of CEC Devices,” page 80.
2. Experiment with the TV’s remote control (slide switch set to TV) to determine
which device functions it can operate.

246 Series TVs. Follow these steps to enable redisplay
of the Auto Output Sensing screen.
1. Repeatedly press the AUDIO key to display the Subwoofer option and change it to Off.
2. Power off the TV.
3. Disconnect the subwoofer from the TV.
4. Power on the TV.
5. Connect the device to the SUBWOOFER OUTPUT
(AVR AUDIO R) jack and the Auto Output Sensing
screen will display.

Any Connection Type
A/V
Device

TV
HDMI
Cable

CEC-Enabled
A/V Device

Source device connected to an A/V receiver connected to the TV
A/V Receiver with HDMI Output (no CEC)
1. Assign the device to an A/V receiver input to allow you to set up NetCommand
IR control of the A/V receiver’s keys as desired. See “IR Emitter Placement,”
page 55, and “Setting Up NetCommand Control of an A/V Receiver,” page 60.
2. Set up NetCommand IR control of the source device’s keys as desired. See
“Initial NetCommand Setup for Most Devices,” page 56.

Source
Device

Any Connection Type

A/V Receiver
HDMI
Cable

Change the setting using the remote control’s AUDIO key
or the AV > Audio > Speakers menu.
Resetting the SUBWOOFER OUTPUT Jack (AVR
AUDIO R)

2. TV Setup

CEC-Enabled HDMI A/V Receiver
1. Turn on the TV’s NetCommand for HDMI feature. See the instructions in Appendix E, “NetCommand HDMI Control of CEC Devices,” page 80.
2. Try using the TV’s remote control to operate the A/V receiver’s volume and mute
functions.
3. If the source device you want to connect also has CEC capability, see Appendix
E for setup.
4. Try using the TV’s remote control to determine which device functions it can
operate. For example, on a CEC-enabled DVD player, check for a response
to the
(Play),
(Pause), and
(Stop) keys. For a cable box, check for a
response to CH/PAGE
/ .

CEC-Enabled
Source Device
HDMI
Cable
A/V Receiver

HDMI
Cable

2. TV Setup

Using the TV with a Personal Computer

Connecting a Computer to the TV
Use one of the connection methods listed below based
on your computer’s video output.

DVI-to-HDMI cable
or an HDMI cable
with an HDMI-toDVI adapter

Audio
Connection
Stereo audio
cables

HDMI-to-HDMI
cable

Computer with
DVI and stereo
audio outputs

4.
5.

TV main
panel

S-VIDEO

INPUT3

Pr
VIDEO

L
AUDIO

R
Y

DVI/PC

AUDIO

R
INPUT2

INPUT1

DIGITAL
AUDIO
OUTPUT

AUDIO

AVR AUDIO
OUTPUT

ANT2/AUX

ANT1/MAIN

A DVI connection from a personal computer requires
a separate audio connection. Computer connected to
the TV main panel (above).

Computer with
HDMI audio/video
output

HDMI

1
IR- NetCommand

5. Press FORMAT repeatedly to find the

picture format best suited to the
image. See the chart on this page
showing how different computer resolutions can be displayed on the TV.

S-VIDEO

Output / External
Controller Input

INPUT3

Pr
VIDEO

L
AUDIO
R
Y

DVI/PC

Y / VIDEO

AUDIO

R
INPUT2

INPUT1

DIGITAL
AUDIO
OUTPUT

AVR AUDIO
OUTPUT

ANT1/MAIN

TV main panel

An HDMI-to-HDMI connection carries all video and
audio on a single cable.

Tip
Set the computer’s screen saver to display a pattern
after several minutes of inactivity. This acts as a
reminder that the TV is powered on.

this, press INPUT to open the Input Selection menu,
move the highlight to the PC icon, and press ENTER.
Working from the computer, change the resolution
of the computer image. View the computer image
on the TV and maximize the computer resolution
while maintaining a suitable aspect ratio for the
image.
Computer Display Formats
Perform TV video adjustments. Press
VIDEO repeatedly to access videoPress the FORMAT key repeatedly to cycle through the TV displays
adjustment options. The following
available for your computer’s video signal.
additional adjustments are available
for computer video:
Computer Signal
As Displayed on TV Screen
Horiz Position (Horizontal Position).
4X3
16 X 9
Original Format
Zoom
Manually adjust the horizontal
Standard
Standard
position.
VGA
Vert Position (Vertical Position).
640 X 480
Manually adjust the vertical position.

Distortion in Computer Images
Computer images may show distortion
when viewed on the TV, e.g., lines that
should be straight may appear slightly
curved.

ANT2/AUX

If your computer provides digital audio
output (coaxial or digital), you can connect it
directly to a digital A/V receiver and bypass
the TV.

Y / VIDEO

DVI/PC

No additional
audio connection is required.

that your computer signal is compatible with the TV.
Connect the computer’s digital signal output to one
of the TV’s HDMI jacks. See the connection diagrams for the method suited to your equipment.
Connect the computer’s audio output using one of
these options:
• For digital DVI signals, connect analog left/right
audio to the TV’s DVI PC AUDIO INPUT jacks.
• For HDMI signals, no additional audio connection is required.
Power on the TV and computer. The TV will detect
the connection and display the Auto Input Sensing
screen.
In the Auto Input Sensing screen, press
to
highlight PC in the list of device types. It is important to use the name PC so that the TV can process
the video signal correctly.
Press EXIT to close the Auto Input Sensing screen.

Note:

Output / External
Controller Input

1. See the TV specifications in Appendix A to confirm

IMPORTANT
This TV accepts digital computer signals only.

1. Power on the computer if it is not already on.
2. Select PC from the Input Selection menu. To do

HDMI

IR- NetCommand

Note: If the computer’s audio output
is a single mini jack, a mini audio-toRCA-male “Y” adapter cable is also
required.
HDMI

(480i / 480p / 720p / 1080i)

Digital DVI

Video Connection

Computer Video Adjustments

(480i / 480p / 720p / 1080i)

Computer
Video Output

2. TV Setup

Image Resolution

WVGA
848 X 480
SVGA
800 X 600
WSVGA
1064 X 600
Original Format

Zoom

Standard

Reduce

XGA
1024 X 768

Your Mitsubishi TV can display resolutions
from standard VGA (640 x 480) through
1920 x 1080 signals at a refresh rate of
60 Hz. See Appendix A, “Specifications”
(page 66) for more on compatible screen
resolutions.

PC 720p
1280 X 720

In most cases, the computer will select
the best resolution match to display on
the TV. You can override this setting if you
wish. Refer to your computer operating
system’s instructions for information on
changing the screen resolution.

SXGA
1280 X 1024

You may need to restart the computer for
changes to take effect.

Standard

WXGA
1360 X 768

Original Format
PC 1080p
1920 X 1080

2. TV Setup

Using a CableCARD
246 Series TVs
The CableCARD™ system allows your TV to receive,
decode, and unscramble the premium digital channels
included in your cable TV subscription without the use
of a cable box. The system is unidirectional, meaning
that certain digital cable services, such as requests
for video-on-demand and pay-per-view programs, a
cable operator’s enhanced program guide, and dataenhanced television services may require use of a
set-top box instead. For more information, call your
local cable operator.
Note:

CableCARD requires the TV’s Fast Power On
setting. If you insert a CableCARD, the TV will
automatically override a Low Power setting and
change to the Fast Power On setting.

Installing a CableCARD

2.
3.

incoming cable to
ANT1/MAIN on the
back of the TV.
Power on the TV.
Insert the CableCARD
into the CableCARD
slot with the front of
the card oriented as
shown in the diagram
below.

TV main panel

Press EXIT to exit.

Sample CableCARD information screen. Write down
the information before contacting your cable provider.

CableCARD Menu
CableCARD menu
Network Setup
CableCARD(tm) Status
CableCARD(tm) Pairing
Conditional Access
Sample CableCARD menu

HDMI

1
IR- NetCommand

S-VIDEO

Output / External
Controller Input

INPUT3

(480i / 480p / 720p / 1080i)

1. Connect your primary

In order to start cable
service for this device, please contact
your cable provider
1-800-xxx-xxxx
CableCARD(tm): xxx-xxx-xxx-xxx-xxx-x
Host: xxx-xxx-xxx-xxx-x
Data: xxx-xxx-xxx-xx
UnitAddress: xx-xxxxx-xxxxx-xxx

Pr
VIDEO

ANT1/MAIN

L
AUDIO
R
Y

DVI/PC

Y / VIDEO

L
AUDIO

AUDIO

R
INPUT2

INPUT1

DIGITAL
AUDIO
OUTPUT

AVR AUDIO
OUTPUT

ANT2/AUX

ANT1/MAIN

To ANT 1

To display the CableCARD menu with links to applications from your cable provider:
1. While watching CableCARD, press INPUT to open the
Input Selection menu.
2. With the CableCARD icon highlighted, press MENU to
open the CableCARD menu.
3. Press
to highlight a link, then press ENTER to
access the linked page.
4. To redisplay the CableCARD menu, repeat steps 1
and 2.
5. Press EXIT to return to TV viewing.
If there are technical problems with the CableCARD, an
error screen automatically displays with information that
may be needed by your cable provider when you call
them for assistance.

4. Wait a few moments while the CableCARD initial-

izes. A message will display on screen when initialization is complete.

Displaying CableCARD Information
To display information needed by your service provider
to start cable service, press MENU and when the Main
menu appears, press 9 9 9.

Moving Through Other CableCARD Screens
In addition to CableCARD menus, other CableCARD
application screens may display and require you to
make additional selections. When using these screens
on your Mitsubishi television:
• Blue text denotes a function. Press ENTER to perform
the function.
• You cannot move backward through the links. To
exit the CableCARD system, press EXIT. The CANCEL
key may not work with some CableCARD screens.
Contact your cable provider if you have any problems
with the application screen displays.

TV Connections

Before You Begin
Auto Input Sensing

Surround Sound

The TV’s Auto Input Sensing feature automatically recognizes most connections and prompts you to identify
the type of device connected. See page 14 for more on
Auto Input Sensing.

For best surround sound audio quality, route audiosignal cables or HDMI cables from the source device
directly to your A/V receiver or sound system.

Connection Types
Review the connection types available on your input
devices and use connections that will give the best
video quality. For example, choose HDMI over component video, and choose component video over S-video
or composite video.

IMPORTANT
Accessory items such as cables, adapters,
splitters, or combiners required for TV
connections are not supplied with the TV.
These items are available at many electronics
stores.

Picture Quality
For best picture quality, route signals directly from
the input device to the TV; avoid routing video signals
through an A/V receiver, for example.

Cable Management
One cable tie with a locking pin is supplied with the accessories. Use the tie to keep cables organized and connected.

Cable Routing

Installing the Cable Tie
1. Remove the locking pin from the cable tie and
2.

insert the anchor prongs into the hole on the back
of the TV.
Reinsert the pin in the cable tie to secure the tie to
the TV.

Cable tie

)PMFJOCBDLPG57 Cable routing on

back of TV

$BCMFUJF

1JO

Unlatching the Cable Tie

#BDLPG57

)PMFJO
CBDLPG57

IMPORTANT
Be sure to leave enough cable slack below the cable tie
to allow the TV to swivel freely. Without enough slack,
there is a risk of damaging the cables and the TV.

Pry up the latch tab and push or pull
the free end of the tie through the
latch.
You may be able to lift the latch tab
by pinching the tab and latch body
between your thumb and index finger.
You may find it easier to pry up the
latch tab using a plastic wallet card or
similar object.

Pry up tab
to release

3. TV Connections

HDTV Cable Box or Satellite Receiver, DVD Player, or Other Device with
Component Video
If your cable box or satellite receiver has an HDMI
output, use the connections for HDMI devices
described on this page.

Figure 1. Connecting a device with
component video outputs

(480i / 480p / 720p / 1080i)

Analog stereo audio cables and a DVI-to-HDMI cable or
DVI/HDMI adapter and HDMI cable are required.

Pb
3

HDMI cable with DVI/HDMI adapter from the DVI
device’s back panel to the TV’s HDMI jack.

Y / VIDEO

Note:

AUDIO

1
IR- NetCommand

S-VIDEO

Output / External
Controller Input

INPUT1

If you are using a DVI/HDMI adapter, it is important to connect the adapter to the DVI device for
best performance.

INPUT3

Pr
VIDEO

L
AUDIO
R
Y

DVI/PC

Y / VIDEO

AUDIO

INPUT2

DIGITAL
AUDIO
OUTPUT

INPUT1

on the DVI device back panel to the DVI/PC INPUT
AUDIO on the TV main panel. Connect the red
cable to the R jack and the white cable to the L
jack.

AVR AUDIO
OUTPUT

ANT2/AUX

Note:
L
R
AUDIO

ANT1/MAIN

Incoming from
cable service or
satellite dish

CABLE IN or
SATELLITE IN

HDMI Device (Cable Box, Satellite Receiver, DVD Player, or Other Device)

Note: Refer to the cable box or satellite receiver
Owner’s Guide for cable or dish antenna connections to the receiver.

HDMI

Some devices require connection to an analog input
first in order to view on-screen menus and to select DVI
as the ouput. Please review your equipment instructions for DVI connectivity and compatibility.

TV main panel
3

S-VIDEO

TV
main
panel

HDMI

Digital DVI device

S-VIDEO

Output / External
Controller Input

AUDIO
R
L

INPUT3

DVI/PC

AVR AUDIO
OUTPUT

S-VIDEO

INPUT3

(480i / 480p / 720p / 1080i)

VIDEO
INPUT3

AUDIO

Any HDMI
device

Y / VIDEO

R
Y

DVI/PC

AUDIO

R
INPUT2

INPUT2

INPUT1

DIGITAL
AUDIO
OUTPUT

INPUT1

DIGITAL
AUDIO
OUTPUT

R
L
AUDIO

AVR AUDIO
OUTPUT

ANT1/MAIN

TV main
panel

DVI/PC
L

AVR AUDIO
OUTPUT

AUDIO

IMPORTANT
ANT2/AUX

R
ANT2/AUX

ANT1/MAIN

Figure 2. Connecting an HDMI device.
Note: HDMI inputs are
certified for proper
interoperability with other products certified by
Simplay™.

AUDIO

ANT2/AUX

ANT1/MAIN

3.
Incoming
cable from
wall

CABLE IN or
SATELLITE IN

Figure 4. Connecting a device with S-Video

Y / VIDEO

AUDIO

Pr
VIDEO

S-VIDEO

Output / External
Controller Input

DVI/PC

INPUT1

1
IR- NetCommand

Figure 3. Connecting a digital DVI device

AUDIO

Output / External
Controller Input

Connect audio
cables to INPUT
3 AUDIO

AUDIO

DIGITAL
AUDIO
OUTPUT

IR- NetCommand

Y / VIDEO

INPUT2

Any S-Video
device

S-VIDEO
OUT

IR- NetCommand

DVI OUT

AUDIO

HDMI

Digital Surround Sound: The TV’s HDMI inputs
can receive digital stereo audio signals only. To
hear digital surround sound from an HDMI device,
connect the device’s HDMI or digital audio output
directly to your A/V receiver. See the Owner’s
Guides for those devices for instructions.

AUDIO

HDMI and Audio Signals

lite service to CABLE IN or SATELLITE IN on the
cable box or satellite receiver.
Connect an S-Video cable from S-VIDEO OUT on
the cable box or satellite receiver back panel to
INPUT 3 S-VIDEO on the TV main panel.
Connect left (white) and right (red) audio cables
from AUDIO OUT on the cable box or satellite
receiver to INPUT 3 AUDIO L and R on the TV main
panel.

VIDEO

(480i / 480p / 720p / 1080i)

Mitsubishi recommends you use category 2 (highspeed) HDMI cables to connect HDMI 1.3 source
devices. High-speed category 2 cables bring you the
full benefits of Deep Color and x.v.Color. See “HDMI
Cable Categories,” page 10, for more on HDMI cable
types.

1. Connect the cable from the outside cable or satel-

The HDMI connection supports copy protection
(HDCP).

Required: HDMI-to-HDMI cable.
Connect an HDMI cable from the TV main panel to the
HDMI device output. HDMI devices provide video and
audio through the single cable.

Required: S-Video cable and left/right analog stereo
audio cables.

2. Connect a set of audio cables from AUDIO OUT

TV
main
panel

Standard Cable Box, Satellite Receiver,
or Other Device with S-Video

1. Connect the DVI-to-HDMI cable (recommended) or

the cable from the outside cable or satellite service
to CABLE IN or SATELLITE IN on the cable box or
satellite receiver. See your device’s owner’s guide
for instructions and cable compatibility.
To hear digital surround sound, connect the digital
audio output from the device directly to your digital
A/V receiver.

HDMI

3. Cable Box or Satellite Receiver Only: Connect

Note:

DVI Video Device (Cable Box, Satellite
Receiver, DVD Player, or Other Device)
Connect DVI devices (digital only) to the TV’s HDMI
input jacks.

(480i / 480p / 720p / 1080i)

Required: RCA component video cables, left/right
analog stereo audio cables.
1. Connect RCA-type cables from the Y Pb Pr outputs
on the device to the Y Pb Pr inputs on the TV main
panel, matching the colored green, blue, and red
connections.
2. Connect left (white) and right (red) audio cables
from the device to AUDIO L and R on the TV main
panel.

3. TV Connections

(480i / 480p / 720p / 1080i)

R
O

3. TV Connections

It is very important to connect the incoming cable for
your primary viewing source to ANT 1. 3

1. Connect the primary incoming coaxial lead cable to
2

ANT 1 on the TV main panel.

2. For an optional secondary antenna source, connect
1

an antenna (or cable) to ANT 2.

IR- NetCommand

VCR to an Antenna or
Wall Outlet Cable

Antennas with Separate UHF and
VHF Leads
Required: UHF/VHF combiner

1. Connect the UHF and VHF antenna leads to the

Required: Two-way RF splitter, two coaxial cables, right
and left analog audio cables, either S-video or composite video cable.

2. Push the combiner onto ANT 1 on the TV main

1. Connect the incoming cable or antenna to IN on the

UHF/VHF combiner.

RF splitter.

panel.

2. Connect one coaxial cable from OUT on the RF

S-VIDEO

Output / External
Controller Input

splitter to ANTENNA IN on the VCR back panel.
Connect one coaxial cable from OUT on the RF
splitter to ANT 1 on the TV main panel.
Connect either an S-Video or composite video
cable from VIDEO OUT on the VCR back panel to a
VIDEO composite or S-VIDEO jack on the TV main
panel. Connect only one type of video cable;
S-Video is recommended, if available.
To use the TV speakers with the VCR, connect left
(white) and right (red) audio cables from AUDIO OUT
on the VCR to the associated AUDIO L and R jacks
on the TV main panel. If your VCR is mono (nonstereo), connect only the white (left) cable.

(480i / 480p / 720p / 1080i)

INPUT3

Pr
VIDEO

R
Y

DVI/PC

AUDIO

R
INPUT2

INPUT1

ANT1/MAIN

DIGITAL
AUDIO
OUTPUT

Y / VIDEO

ANT2/AUX

HDMI

L
AUDIO

VHF antenna
(channels 2–13)

UHF antenna
(channels 14–69)

Flat twin lead

AVR AUDIO
OUTPUT

To ANT 2

TV
main
panel

ANT1/MAIN

To ANT 1
TV main panel

External antenna
or cable

INPUT3

L
AUDIO
R
Y

DVI/PC

strongly recommends you avoid using
antennas with flat twin leads. Flat twin lead
antenna wires are subject to interference which
may adversely affect the performance of the TV.
We recommend using coaxial antenna cable.

3.
4.

S-VIDEO
OUT

ANT1/MAIN

AVR AUDIO
OUTPUT

S-VIDEO
OUT

1. 300-ohm-to75-

VIDEO
OUT

TV
main
panel

ANTENNA
IN
IR- NetCommand

Pr
VIDEO

L
AUDIO
R
Y

DVI/PC

HDMI

Figure 6. Connecting separate UHF and VHF Antennas

Y / VIDEO

AUDIO

R
INPUT2

TV main panel

B. For cable or antenna with coaxial lead

Connect the coaxial lead directly to ANT 1 on the
TV main panel.

ANT2/AUX

S-VIDEO

IR- NetCommand

VIDEO

INPUT3

Pr
VIDEO

L
AUDIO
R
Y

AUDIO
R
Y

DVI/PC

Y / VIDEO

AUDIO

Y / VIDEO

INPUT2

AUDIO

R
INPUT2

INPUT1

VIDEO

L
AUDIO
R

INPUT1

AUDIO

S-VIDEO

Output / External
Controller Input

A2.

(480i / 480p / 720p / 1080i)

INPUT3

DVI/PC

DIGITAL
AUDIO
OUTPUT

AVR AUDIO
OUTPUT

DIGITAL
AUDIO
OUTPUT

ANT1/MAIN

AVR AUDIO
OUTPUT

A1. Optional 300-ohm-

to75-ohm matching
transformer

S-VIDEO
OUT

Figure 7. Connecting a Single Antenna Lead

ANT2/AUX

INPUT1

ANT1/MAIN

Output / External
Controller Input

AUDIO

AVR AUDIO
OUTPUT

IR- NetCommand

300-ohm
flat twin
lead

ANT1/MAIN

A. For an antenna with flat twin leads

75-ohm
coaxial
lead

VIDEO

DIGITAL
AUDIO
OUTPUT

S-VIDEO
2

Required: 300-ohm-to-75-ohm transformer.
A1. For an antenna with flat twin leads, connect the
300-ohm twin leads to the 300-ohm-to-75-ohm
transformer.
A2. Push the 75-ohm side of the transformer onto
ANT 1 on the TV main panel.

Audio and
video from
cable box
to TV

INPUT3

Antenna with a Single Lead

S-VIDEO

Output / External
Controller Input

ANT1/MAIN

OUT

ohm combiner

ANT2/AUX

Cable 4.
box

S-VIDEO

AUDIO OUT
L
R

VCR

ANTENNA
IN

HDMI

INPUT1

AUDIO OUT
L
R

DIGITAL
AUDIO
OUTPUT

VIDEO
OUT

VCR

R
INPUT2

S-VIDEO
Mitsubishi
OUT

splitter to CABLE IN on the cable box.
Connect one coaxial cable from OUT on the RF
splitter to ANT 1 on the TV main panel.
Connect one coaxial cable from OUT on the cable
box to ANTENNA IN on the VCR back panel.

AUDIO

1. Connect the incoming cable to IN on the RF splitter.
2. Connect one coaxial cable from OUT on the RF

VHF

Required: Two-way RF splitter, three coaxial cables,
right and left audio cables, S-Video or composite video
cable, plus video and audio cables required to connect
the TV to the cable box.

Y / VIDEO

UHF

S-VIDEO

Output / External
Controller Input

VIDEO

Back Side
view view

Figure 5. Wall Outlet Cable

IR- NetCommand

(480i / 480p / 720p / 1080i)

ANT2/AUX

VCR to a Cable Box (Audio & Video)

(480i / 480p / 720p / 1080i)

Wall Outlet Cable (no cable box)
(can be used with a CableCARD™)

3. TV Connections

(480i / 480p / 720p / 1080i)

R
O

ANT1/MAIN

TV main panel

Incoming
cable

Figure 8. Connecting a VCR to allow recording from an
antenna source.

Incoming
cable

Figure 9. Connecting a VCR to a cable box

5. Connect the cable box outputs to the TV as shown

in one of the options listed below. This connection
allows the TV to receive the best available signal
directly from the cable box.
• Figure 1, page 22: Component video output to
the TV’s Y Pb Pr jacks; analog stereo audio to
the associated AUDIO jacks.
• Figure 2, page 22: HDMI output to the TV’s
HDMI jack.
• Figure 4, page 23: S-Video output to the TV’s
INPUT 3 S-VIDEO jack; analog stereo audio to
the INPUT 3 AUDIO jacks.

3. TV Connections

Note: When using this connection configuration with the
connections used in step 5, it is possible to view
live cable programs through the VCR Device. For
best picture quality always view live cable programs
directly from the TV input connected to the cable
box device.

Older Cable Box

A/V Receiver (Sound System) Using
the TV’s Audio Output

Required: One coaxial cable.
Note: This connection is not recommended. The
other connections described in this chapter
provide better quality audio and video to the TV
and allow NetCommand to work with the cable
box.

Most setups require either a digital audio cable or
analog stereo audio cables. To send audio from TV
channels received on ANT 1, ANT 2, or devices connected directly to the TV, you must use one of the connections shown below.

1. Connect the incoming cable to IN on cable box.
2. Connect one coaxial cable from OUT on the cable

The TV makes all audio available in digital and analog
formats:
• Analog audio coming into the TV is output in digital
stereo format on the DIGITAL AUDIO OUTPUT jack.
• Digital incoming audio is output on the analog AVR
AUDIO OUTPUT L and R jacks.

box to ANT 1 on the TV main panel.
HDMI

Incoming
cable

1.
1
IR- NetCommand

Cable
box

S-VIDEO

Output / External
Controller Input

INPUT3

Pr
VIDEO

OUT

L
AUDIO
R
Y

DVI/PC

Y / VIDEO

AUDIO

R
INPUT2

TV main panel

INPUT1

DIGITAL
AUDIO
OUTPUT

Usually, only one of the following audio connections is
required.
• To connect an analog A/V receiver
Connect left (white) and right (red) audio cables
from AVR AUDIO OUTPUT L and R on the TV main
panel to the TV AUDIO INPUT on the A/V receiver.
• To connect a digital A/V receiver with Dolby
Digital surround sound and PCM audio support:
Connect one end of the digital audio cable to
DIGITAL AUDIO OUTPUT on the back of the TV.
Connect the other end to the COAXIAL DIGITAL
INPUT on the back of the A/V receiver.

A/V Receiver with HDMI Output
Required: One HDMI-to-HDMI cable
This option allows you to view content from devices
connected to an A/V receiver. The A/V receiver can
send audio and video to the TV over a single HDMI
cable. You can use an HDMI connection as described
here in addition to an audio connection from the TV’s
audio output.
You may be able to use the TV’s remote control (with
slide switch set to TV) to operate connected CECenabled HDMI devices. Experiment with your equipment to determine which functions are available to the
TV’s remote control. See Appendix E, page 80.
This setup allows you to use NetCommand-controlled
audio and video switching over the HDMI cable. See
“A/V Receiver Control: Automatic Audio and Video
Switching via HDMI” on page 63.

Cable box
TV main
panel

High-definition
DVD player

HDMI

AVR AUDIO
OUTPUT

VCR

DVD player

ANT1/MAIN
ANT2/AUX

IR- NetCommand

Figure 10. Connecting an older cable box

A/V receiver with
HDMI output

ANT1/MAIN

S-VIDEO

Output / External
Controller Input

Pr
VIDEO

L
AUDIO
R

DVI/PC

AUDIO

R
INPUT2

Digital coaxial cable
(for connecting a
digital A/V receiver)

INPUT1

AVR AUDIO
OUTPUT

DIGITAL
AUDIO
OUTPUT

ANT2/AUX

Pr
VIDEO

DIGITAL
AUDIO
OUTPUT

INPUT3

AUDIO

AVR AUDIO
L
OUTPUT

AUDIO

S-VIDEO

Output / External
Controller Input

Y / VIDEO

IR- NetCommand

Stereo analog cables
(for connecting an
analog A/V receiver)

INPUT3

HDMI OUT

(480i / 480p / 720p / 1080i)

cable from VIDEO OUT on the VCR back panel
to a VIDEO composite or S-VIDEO jack on the TV
main panel. Connect only one type of video cable.
S-Video is preferable to composite video, if available.
To use the TV speakers with the VCR, connect left
(white) and right (red) audio cables from AUDIO OUT
on the VCR back panel to the associated INPUT
AUDIO L and R on the TV main panel. If your VCR
is mono (non-stereo), connect only the white (left)
cable.

(480i / 480p / 720p / 1080i)

6. Connect either an S-Video or composite video

3. TV Connections

(480i / 480p / 720p / 1080i)

DVI/PC

OPTICAL
INPUT
COAXIAL
INPUT

Y / VIDEO

HDMI
cable

AUDIO

R
INPUT2

INPUT1

DIGITAL
AUDIO
OUTPUT

(Video to TV)

AVR AUDIO
OUTPUT

DIGITAL
AUDIO
OUTPUT
ANT2/AUX

ANT1/MAIN

A/V receiver back panel

Figure 11. Connecting the TV to an A/V receiver
Note:
• On rare occasions, an HDMI signal may be copyrestricted and cannot be output from the TV as a
digital signal. To hear these copy-protected signals
through the A/V receiver, use the connection for an
analog A/V receiver.
• Check the A/V receiver’s Owner’s Guide for information concerning use of the digital input and
switching between digital sound and analog stereo
sound from the TV.

ANT1/MAIN

AVR AUDIO
OUTPUT

Optional
analog or
digital audio
connection

Audio from TV to A/V Receiver

Figure 12. An A/V receiver connected to the TV with an
HDMI cable may offer special control capabilities.
To hear sound from devices connected to the TV only,
use the optional audio connection to send audio from
the devices through the TV to the A/V receiver..

3. TV Connections

Camcorder
Convenience input jacks on the TV’s
side panel offer the easiest way to
connect a camcorder. Two different
connection options are described on
this page. You can alternatively use
any of the jacks on the main connection
panel.
Use jacks on the TV’s side panel
to connect a camcorder

B: Composite Video Connection
Required: Composite video and analog stereo audio
cables supplied with the camcorder.
1. Connect the composite video cable from VIDEO
OUT on the camcorder to VIDEO/Y on the front of
the TV.
2. Connect left (white) and right (red) audio cables
from AUDIO OUT on the camcorder to AUDIO L and
R on the front of the TV.

A: Y Pb Pr Component Video Connection
Required: Component video and analog stereo audio
cables supplied with the camcorder.
1. Connect component video cables from VIDEO OUT
on the camcorder to the TV’s Y Pb Pr component
convenience jacks.
2. Connect left (white) and right (red) audio cables
from AUDIO OUT on the camcorder to AUDIO L and
R on the TV.
Pr

AUDIO

Y/
VIDEO

A: Component
video plus
audio

If you wish to connect an audio-only device to the TV, such
as an audio CD player or an MP3 player, follow these instructions.

1. Insert an unused RCA-style connector into the

3.
4.

INPUT 4 VIDEO/Y jack. The presence of this connector activates the TV’s Auto Input Sensing
feature.
When the Auto Input Sensing screen displays,
name the new input CD/Audio or MP3 Player.
Connect left (white) and right (red) audio cables from
AUDIO OUT on the device to AUDIO L and R on the TV.
Keep the connector in the VIDEO/Y jack while using
the audio-only device.

Choosing a Viewing Source

Sleep Timer
The Sleep Timer turns the TV off after the length of time
you set. To set the TV to turn on at a certain time, see
the Setup > Timer menu on page 47.
Setting the Sleep Timer
1. Press SLEEP on the remote control.
2. Press SLEEP additional times to increase the time in
30-minute increments up to the maximum of 120
minutes.
3. Press EXIT or wait five seconds without pressing any
keys for the message to disappear.
4. Press SLEEP to view the time remaining before the
sleep timer turns off the TV.

Input Selection menu

Audio-Only Device

TV Operation and Features

TV back

Choose a viewing source from the Input Selection
menu. The current TV input appears as a full-color icon
in this menu.
1. Press INPUT to display the Input Selection menu. If
there are only two inputs to the TV, INPUT switches
between them without displaying the menu.
2. Highlight an input icon using
.
3. Press ENTER to switch to the input and close the
menu.

Cancelling the Sleep Timer
1. Press SLEEP to display the on-screen message.
2. Press SLEEP repeatedly until OFF is displayed.

More About the Input Selection Menu
• To assign meaningful names to the icons, see the
Inputs > Name menu, page 50.
• To rearrange the icons, see the Inputs > Order
menu, page 50.

Note:

After five seconds of inactivity, the message box
will disappear.

TV back

INPUT 4
INPUT 4

Pr
Pr

Pb
Pb

USB

AUDIO

TV convenience
panel

Y/
VIDEO

AUDIO

Y/
VIDEO

2.
B: Composite video
plus audio

Figure 13. Two connection options for a camcorder.

USB

TV convenience
panel

Y/
VIDEO

AUDIO

Y/
VIDEO

TV Tips
Turning the TV On or Off
To turn the TV on or off, point the remote control at the
front of the TV and press the POWER button. Alternatively, press the POWER button on the TV’s control panel.
Controlling Sound Volume

Audio-only device

Figure 14. First insert an unused RCA-type connector
into the VIDEO/Y jack on the TV side or main panel
before connecting audio cables.

•
•

Press VOL
/
to adjust the sound level.
See also “Controlling A/V Receiver Sound Volume” on
page 16.

Changing Channels (antenna sources)
To change channels:
• Enter the channel number using the number keys
on the remote control and press ENTER. For a two-

•
•
•
•
•

—
part digital channel, such as 3-1, press 3 CANCEL 1
to enter a dash (separator).
Press CH/PAGE
/
to change channels one
channel at a time.
Press and hold CH/PAGE
/
to move quickly
through channels.
Press QV (QuickView) to switch back to the previously tuned channel.
Press GUIDE to display ChannelView channel listings,
highlight a channel, and press ENTER.
Use the Fav (Favorites) feature to set up lists of
favorite channels and tune to them with the FAV key.
See Setup > Edit > Fav1–Fav6 on page 45.

NOTE: Perform channel memorization to make finding
channels easier. See Setup > Scan, page 44.

4. TV Operation and Features

Remote Control
1. POWER: Switches TV power on and off.
2. Slide Switch: Selects the A/V device to be operated by the remote control. Set the slide switch
to TV for operation of the TV, and NetCommandcontrolled devices. Control of additional devices
requires programing (see Appendix C, “Programming the Remote Control.”
3. SLEEP: Sets the TV to turn off within 2 hours in increments of 30 minutes.
4. Digits/Letters: Press digits for channel numbers,
then press ENTER for faster tuning. Use numbers
—
and the CANCEL key to enter digital sub-channel
numbers. Use also for entering letters or names in
menus.
To select letters when naming channels, repeatedly
press the associated number key. Press ENTER to set
the letter. Special characters are available with the 1
key (!, &, blank space) and 0 key (/, *, -).
5. —/CANCEL (SUB-Channel/CANCEL): When entering digital
channel numbers, adds a separator between main
and sub-channel numbers. Clears Fav and some
menu entries.
6. QV (QuickView™): Switches between the current
channel and the last channel viewed.
7. MUTE: Turns TV sound on and off.
8. SPLIT: Not used in this model.
9. FAV (Favorites): Scans through memorized lists of
favorite channels. See Setup > Edit > Fav1–Fav6
on page 45.
10. VOL
/
(Volume Up/Down): Changes sound
level.
11. CH/PAGE
/
(Channel or Page Up/Down):
Scans up or down through memorized channels.
Pages up and down through screens when used with
ChannelView or the TV Guide Daily system.
12. FORMAT: Changes the shape and size of the TV
picture.
13. LIST (246 Series Models): Works like the LIST key for
a cable box or satellite receiver when “learned” for
NetCommand or when the remote has been programmed for the device.
14. INPUT: Displays the Input Selection menu from
which you can select an input source to view, such
as an antenna input (ANT 1/2) or a connected
device.
15.
(Adjust Up/Down/Left/Right): Navigate
menus and change settings.
16. ENTER: Selects a channel number or menu item.
17. GUIDE: Displays or removes ChannelView™ channel
listings or, if enabled, TV Guide Daily listings for
ANT 1 and ANT 2. Displays DVD disc or top menu

4. TV Operation and Features

Remote Control, continued
For devices operating independently of
NetCommand: The F1–F4 keys work like the A,
B, C, D buttons on some cable boxes, satellite
receivers, and DVD players. Program the remote
control for your equipment and test the keys. See
Appendix C, “Programming the Remote Control.”

2
3

1
25.

4
5
6

15
16

24.

9
12

13
14

19
17
18
24 25 26

Record/Playback Keys

Use any of these methods to enable the recording and
playback commands of the TV’s remote control:
• Program the remote control for your DVR, VCR, or
DVD player/recorder and set the slide switch to VCR,
DVD, CABLE/SAT, or AUDIO as appropriate.
• Check HDMI devices for compatibility with the TV’s
NetCommand for HDMI feature (see Appendix E).
• Perform NetCommand IR “learning” for the device.

7
8

(Pause): Freezes a broadcast TV picture from an
antenna source, cable box, or satellite receiver (if
key has not been reassigned for NetCommand use).

20
21
22

27 28 29

for a NetCommand-controlled DVD player. Displays the guide for a NetCommand-controlled cable
box or satellite receiver.
18. INFO: Displays an on-screen summary of the current
device in use and any broadcast information available,
including current V-Chip ratings information. See
“Status Display” on page 32 for details.
19. AUDIO: Selects individual audio settings to adjust.
20. VIDEO: Selects individual video settings to adjust.
21. MENU: Displays the main TV menu. When a submenu is open, backs up one menu level.
22. EXIT: Closes TV on-screen menus/displays.
23. F1–F4
For devices under NetCommand control:
Perform NetCommand “Learning” to assign your
choice of functions to the F1–F4 keys.

(Record): Records with a VCR or DVR.

25.

(Pause): Pauses a VCR, DVR, or DVD. See
above for use during TV viewing.

26.

(Stop): Stops play of a VCR, DVR, or DVD.

27.
28.
29.

(Reverse): Rewinds a VCR. Reverse scans a
DVR or DVD.
(Play): Plays a VCR, DVR, or DVD.
(Forward): Fast forwards a VCR. Forward scans
a DVR or DVD.

Note: To operate other audio/video devices using
the TV’s remote control:
• See Appendix C, “Programming the Remote
Control.”
• For HDMI devices compatible with the TV’s NetCommand for HDMI feature, see Appendix E.
• See chapter 6, “NetCommand IR Control,” for
NetCommand IR “Learning” of device keys.
• For use of specific keys with NetCommand-controlled devices, see “Special Operation Methods,”
page 58.

Resetting the Remote Control
If the slide switch is set to TV and the TV does not
respond properly, reset the remote control.
1. Press and hold POWER for several seconds until the
button blinks twice and goes off.
2. Release the POWER button.
3. Press keys 0 0 9 3 5 and the POWER button will blink
twice when you finish entering the code. While
entering the code, pause for a moment between
each key press to ensure it is recognized.

Care of the Remote Control
•
•
•
•
•
•
•

Use only alkaline batteries.
Be within 20 feet of the equipment.
Do not press two or more buttons at the same time
unless instructed to do so.
Do not allow unit to get wet or become heated.
Avoid dropping on hard surfaces.
Do not use harsh chemicals to clean. Use only a
soft, lightly moistened cloth.
Do not mix old and new batteries.

Low-Battery Indicator
If you press a key and the POWER key blinks five times,
replace the remote control’s batteries.

ChannelView Channel Listings
ChannelView™ displays channel names and program
information, as sent by broadcasters or your local cable
service provider, for memorized channels on ANT 1 or ANT
2. Listings may be incomplete. No program information is
displayed for analog channels. An analog channel name is
displayed only if you assigned a name in the Setup > Edit
menu (page 45).
To receive ChannelView updates:
• Keep the Energy Mode set to Fast Power On
• Set the TV clock
• Leave the TV powered off for a while each day to
receive updates.
Notes:
-- Listings are updated for the digital channel you are
currently watching.
-- If the time or date displayed are incorrect, change
the TV’s time, time zone, date, or Daylight Savings
Time settings in the Setup menu.

Using ChannelView
Feature

Press Key

See ChannelView listings Press GUIDE.
from ANT 1 or ANT 2.
Close ChannelView

Press GUIDE or EXIT.

Scan channels one by one. Press and hold

Scan channels quickly.

Press and hold PAGE

Jump to listings for a
specific channel.

Enter the channel
number (see numbers in
upper left of screen).
2. Press ENTER.
1.

See more of the program Press INFO.
description (if available).
Move navigation to the
program listings.

Press

Move navigation to the
channel listings.

Press

Tune to the highlighted
channel.

Press ENTER.

4. TV Operation and Features

Fav (Favorite Channels)

Status Display
Ant 1

Press the INFO key to see the
on-screen status display.
The most common displays
are shown here. You will
rarely, if ever, see all status
indicators at the same time.

6
7
FAV1
English 12

Tuesday 9:10 PM

Sleep 30 min

15 MUTE

Use the six Fav channel banks to store groups of your
favorite channels from ANT 1 and ANT 2. You can set
up a Fav channel bank for each of your favorite program
types or set up a bank for each TV user.

7-1 KABC-HD 4 Monday Night Football

HD 16:9 Standard
TV-PG
9
Stereo
11

On-screen status display
sample information

St. Louis vs. Tampa Bay
8
8

You may prefer to perform Fav channel setup from a
menu. See the Setup > Edit options, page 45.

ANT-1
480i Stretch
TV-PG
Stereo SAP

4
FAV2

FAV

Channel and Fav numbers in the
on-screen status display

Signal Strength 16

Analog Sources

Digital Sources

Source antenna or input

Analog channel being received (antenna sources only)

Digital major and sub-channel numbers (antenna
sources only)

Analog channel name (if named in the Setup >
Edit menu or supplied by TV Guide Daily); antenna
sources only.

Digital Channel Name (if broadcast or if named in the
Setup menu > Edit options; antenna sources only)

Program name (if supplied by TV Guide Daily)

Program name (if broadcast)

Signal Type Being Received

Screen Format in use

Screen Format in Use

Current Fav bank number of channel (antenna
sources only)

Program description (if supplied by TV Guide Daily)

Program description (if broadcast); antenna sources
only)

V-Chip rating (antenna sources or VIDEO composite
and S-VIDEO jacks only)

V-Chip rating (antenna sources only)

10.

Audio Source. Possible:

TV speakers,

4. TV Operation and Features

external sound system

TV speakers,

external sound system

11.

Listen To indicator. Possible: Stereo, Mono, SAP
(antenna sources only))

Listen To indicator. Possible: Stereo, Surround, Dual
Mono

12.

(Does not apply)

Current available language (antenna sources only)

13.

Day and time

14.

Sleep Timer remaining time

15.

Mute indicator

16.

(Does not apply)

Signal strength indicator (antenna sources only)

Using Fav Channels
See the current Fav bank number

Press INFO.

View channels in current Fav bank

1. Press the FAV key. Wait for the TV to tune to a channel in the current Fav bank.
2. Press the FAV key repeatedly to cycle through the channels available in the
current Fav bank.

Change Fav banks

1. Press the FAV key. Wait for the TV to tune to a channel in the current Fav bank.
2. When tuning is complete and while the TV status display is still visible on
screen, press the number key for the desired bank (1–6).
Note: Wait for the channel change to finish before pressing the number key.
Otherwise, the TV may ignore the Fav number.

If no Fav banks are set up

The FAV key switches to the previously tuned channel; works like the QV key.

Fav Setup Using Only the Remote Control
Add Fav channels

1. While watching TV, tune to the channel you want to add to the current
Fav memory bank. The default bank is Fav1. See the instructions above
if you need to change to a different Fav bank.
2. Press and hold the FAV key for about 2 seconds. When FAV and the
memory bank number appear under the channel number, the channel
has been successfully added.

Remove Fav channels
This procedure removes the channel
only from the selected bank and
leaves the other banks unchanged.

1. While watching TV, press the FAV key.
2. While the TV status display is still visible on screen, press the number
key for the memory bank.
3. Press the FAV key repeatedly until you see the desired channel in the onscreen status display.
4. While the channel number and FAV indicator (with correct bank number)
are still displayed on the screen, press CANCEL. You must press CANCEL
while the indicator is displayed. When the FAV indicator disappears
after pressing CANCEL, the channel has been successfully removed.

4. TV Operation and Features

TV Signals and Display Formats
This is a 16:9 widescreen TV suitable for images available from HDTV and many DVDs. You can view olderstyle squarish images (4:3 aspect ratio) using one of the
display formats described on this page. Press the FORMAT
key to cycle through the available display formats. The TV
remembers the format you last used for each input.

DVD Image Definitions
Image information may be stated on the DVD case. Some
DVDs support both of the formats described below.
Anamorphic (or Enhanced for WideScreen TV)
Indicates DVDs recorded to show widescreen images properly on 16:9 TV sets using the TV’s Standard format mode
(recommended).
Non-Anamorphic (or 4:3, 1:33:1, Letter Box, or
Full Screen)
Indicates DVDs recorded for viewing on squarish TV
screens. They may be full screen (4:3 or 1:33:1) which
crops movies to fit the narrow TV, or letter box, which
adds black top and bottom bars.

Original
Signal
TV
Display
Standard

Non-anamorphic or
SD 4:3
Distorted. Not
recommended.

TV Display Format Definitions
Standard: This is the full-screen format used by HDTV
signals. Use this format to display anamorphic DVDs with a
1.78:1 or 1.85:1 aspect ratio. Anamorphic DVDs with a 2.35:1
aspect ratio are displayed correctly but with top and bottom
black bars. Narrow (4:3) images are stretched evenly from
side to side. Available for all signals.
Expand: Enlarges the picture to fill the screen by cropping
the top and bottom; useful for reducing the letter box top and
bottom bars of non-anamorphic DVD images.
Zoom: Enlarges the picture to fill the screen by cropping the
sides, top, and bottom to eliminate black bars. 480i/480p and
SD 4:3 signals: Eliminates top and bottom bars on anamorphic DVDs with a 2.35:1 aspect ratio. 720p, 1080i, SD 16:9,
and HD signals: Eliminates bars added to 4:3 images.
Stretch: Stretches a narrow 4:3 image across the screen
to display the entire image with less distortion than the
Standard format.

JPEG Images and the USB Photo Port
Anamorphic DVD
Recommended

For instructions on viewing the
GalleryPlayer demo or to purchase images, see page 49.
1. Back up the data on
your USB drive before
connecting it to the TV.
Mitsubishi is not responsible for file damage or
Optional
audio
data loss.
device
2. Connect your USB card
reader or USB drive to
the TV’s USB Photo port.
The TV will begin reading files.
3. Wait until you see the
completion message on
screen before continuing.
If GalleryPlayer images
and personal images are
stored on the device, a
menu will display to let you choose which to view.

Expand

Zoom

Stretch

Stretch
Plus

Narrow

Recommended
for letterbox.
See Note 1.

Distorted; not
recommended.
See Note 1.

Distorted. Not
recommended.
See Note 1.

Recommended
for anamorphic
2.35:1 images.
See Note 1.

Recommended
for standard
broadcasts.
See Note 1.

Distorted; not
recommended.
See Note 1.

Recommended
for standard
broadcasts.
See Note 1.

Distorted; not
recommended.
See Note 1.

See Note 1

Distorted; not
recommended.
See Note 1.

Original Signal
SD 16:9 or
HD Digital
720p,
1080i,
1080p
Signal

Display Formats
Standard

Zoom

(except
720p )

Recommended to remove bars from the top,
bottom, and sides.

Full
Best for computer or
Native game images (component and HDMI only)

TV Display Formats. Press the FORMAT key repeatedly to
see the displays available for the current program. Press
the INFO key to see the name of the display format in use.
Note 1: Available for 480i, 480p, and digital SD 4:3 signals only.

Stretch Plus: Similar to Stretch, but minimizes distortion on
the sides by expanding the picture to crop off portions of the
top and bottom. You can adjust the vertical position of the
picture. Press VIDEO repeatedly to show the Vert Adjustment
option, then press ENTER. Use
to move the picture.
Narrow: Displays narrow 4:3 images in their original
shape. Adds black side bars to fill the screen.
Wide Expand: Enlarges the picture, cropping the image on
both sides. Removes or reduces black side bars added to
narrow images converted to 16:9 signals for digital broadcast.
Note: All high-definition channels send widescreen (16:9)
signals, but not all programming was created for this
format. The broadcaster may stretch the image or add
side bars to fill the widescreen area.
Full Native: Displays all pixels in the original image; best for a
computer or game image (component and HDMI inputs only).

Use these keys while viewing JPEG thumbnail images.
Not all keys are available with GalleryPlayer files.
Keys for the JPEG Thumbnail Menu
Move the highlight from image to image.

Y/
VIDEO

FORMAT

Rotate the thumbnail clockwise in 90˚ increments (personal photos only)

or
ENTER

Play the slide show starting with the highlighted thumbnail.

USB

Note:

Use for widescreen images.

Wide Recommended to reExpand move side bars.

JPEG Thumbnail Menu

INPUT 4

Signal Definitions
480i: Traditional interlaced signals from ANT-1 and ANT 2,
composite VIDEO, component Y Pb Pr, and HDMI jacks.
480p: Progressive-scan DVD signals on component Y Pb
Pr and HDMI jacks.
720p and 1080i: High-definition signals received through
component Y Pb Pr and HDMI jacks. These signals are
always 16:9 (widescreen).
SD 4:3: Standard-definition squarish-screen-format
signals from digital channels on ANT 1 and ANT 2.
SD 16:9: Standard-definition widescreen-format signals
from digital channels on ANT 1 and ANT 2.
HD 16:9: High-definition 16:9 widescreen signals from
digital channels on ANT 1 and ANT 2.

Viewing Camera Files and GalleryPlayer Images

AUDIO

If the TV is unable to display photos from an
incompatible device, you can:
- Transfer files to a different USB device.
- Use your camera’s composite video output
as described on the next page.

Highlight the last thumbnail on the current page.
Highlight the first thumbnail on the current page.
CH/PAGE /

Display the next or previous page of thumbnails.

EXIT

Close the Thumbnail menu and display the
USB Photo menu.

Close the Thumbnail menu and display the
Main menu.

INPUT

Close the Thumbnail menu and display the
Input Selection menu.

4. Refer to the table below for use of the USB Photo
5.

menu after files have been read.
Optional: Connect an audio device to the convenient
INPUT 4 AUDIO L and R stereo jacks to play sound
while viewing pictures.

USB Photo Menu Options
Start slide show.

With the Slideshow icon highor ENTER.
lighted, press

Activate menu options. Highlight an icon and press
ENTER to:
• start the slide show
• display picture thumbnails
• open the Media Setup
submenu.
Display or close the
Main menu.

Press MENU.

Display status for the
file source.

Press INFO.

Select a different con- 1. Press INPUT.
nected device
2. Highlight the icon for a different device.
3. Press ENTER.
Clear status display
or menu to show the
USB Photo menu

Press EXIT.

JPEG Thumbnail Menu
Notes on Viewing Images from the USB Photo Port
• The TV ignores all commands while reading files. Wait for
the completion message before continuing.
• Large files or high-capacity storage devices may take
a long time to display. The screen will be blank while
files are read.
• Use only one source device at a time.
• If your USB storage device contains both personal images
and GalleryPlayer images, you can view only one type per
session. To view a different image type, press (STOP) to
stop playback. Press INPUT to display the Input Selection
menu and select the USB input. When the Media menu
displays, select either GalleryPlayer or Photos.
IMPORTANT
Stop playback or change to a different TV input
before disconnecting from the USB photo port.

4. TV Operation and Features

Slide Show

USB Photo Menu Compatible Picture Files

Use these keys during the slide show:

•

Keys for JPEG Picture Slide Show
Begin or resume slide show playback
Pause or resume playback while in automatic advance mode.
or
ENTER

•

Advance to the next slide.
•
Go to the previous slide.

FORMAT

Rotate the slide clockwise in 90˚ increments (personal photos only).

•

Stop slide show and display the USB Photo
menu.

•

INFO

Display status for the viewing device and
current image (personal photos only).

INPUT

Display the Input Selection menu.

Display or remove the TV Main menu.

Note:

Always press (STOP) to stop slide show playback before disconnecting from the USB Photo
port.

Still images recorded on digital cameras using the
Exchangeable Image File Format, version 2.1 (EXIF
2.1) standard for digital still cameras and Design
Rules for Camera File Systems version 1.0 (DCF 1.0)
Some images opened and resaved on a computer
may not play back or may not display in the thumbnail list. This happens if the files were resaved in an
incompatible format.
Full path file names can be no longer than 50 characters and must end in a .jpg extension. Only the
first 20 of the 50 characters will display.
Images on storage devices with a capacity of over
256 MB can take a longer initial time to display.
The storage device must use the FAT/FAT32 files
system.

Main Menu
Press MENU on the remote control to open the Main menu.
Icon

Menu Name and Description

AV Menu

Connect the camera to the TV using a composite video
cable if:
• You are unable to see images using the USB photo
port.
• You wish to view moving video from the camera.

1. Refer to the owner’s manual supplied with the
2.
Media Setup menu
In the Media Setup menu you can adjust the slide show
display, number of repetitions, or display interval.
• Select either Auto or Manual advance. During
manual operation, press
or ENTER to advance to
the next slide.
• For automatic advance, select the time interval for
display of each slide. The interval you select here is
the minimum time between slides; actual time may
be longer for larger files.
• For automatic advance, select the number of times
(frequency) to play the complete slide show: Once,
Twice, or Continuous.
• Press EXIT to close the Media Setup menu and
return to the USB Photo menu.

4.
5.
6.
7.

IMPORTANT
The TV can read JPEG photo files as created by
the camera. If you edit a photo file on a computer
and resave the image, the TV may be unable to
read the resaved file.

AUDIO

Y/
VIDEO

Camera connection
using a composite
video cable

USB

0QUJPOBM
"VEJP$BCMF

Setup Menu

Perform basic TV setup. Set language, scan
(memorize) channels, set the TV clock, edit
channel options, lock TV use by channel, set
Energy Mode, auto-on TV Timer. View a GalleryPlayer demo and obtain a setup key.

Inputs Menu

Assign names to TV inputs, change icon order
in the Input Selection menu, perform NetCommand IR “learning,” set up the TV Guide Daily
system.

Lock Menu

Restrict TV use by program ratings and by time
of day. Disable the control-panel buttons. Set
a pass code.

Main menu

Remote Control Keys for the TV Menu System

5
6

Key

Function

Display or close the Main menu or move back one menu level.

exit

Close all menus and return to TV viewing.

(Adjust Left/Right Keys)

•
•
•

(Adjust Up/Down Keys)

Customize picture and sound settings.
Turn closed captions on and off; customize

Camera Photos and Moving Video as
Composite Video

camera for instructions needed for this setup.
Set the camera’s output signal type to NTSC and
put the camera into playback mode.
With the camera still turned on, connect your digital
camera’s composite video cable (usually yellow) to
the VIDEO/Y jack on the TV. To hear audio, connect
the camera’s audio output cable to the AUDIO L
jack.
When the Auto Input Sensing screen displays,
press EXIT or assign the name Camcorder.
Press INPUT to display the Input Selection menu.
Highlight the icon for the camera input and press
ENTER.
If viewing photos,
advance through
INPUT 4
the images manually or set the
Pr
camera to advance
Pb
automatically.

Page

Captions Menu caption displays.

The TV’s USB Photo menu will be unavailable and
you must control the slide show through the camera.
Display resolution is standard-definition (480i).

Media Setup Menu

TV Menus

4
1
2

Move through screens to select menu options.
Change settings.
Scroll through lists.

ENTER

Start an automatic function or check/uncheck a check box. When
setting time, move from hour digits to minutes digits and from
month to day to year digits.

Numbers
Letters

Enter channel numbers.
Enter custom names in some text boxes.

CANCEL

•
•

INFO

Get context-sensitive help.

Clear a setting or stop an automatic function.
Add a separator in a digital channel number.

5. TV Menus

AV Menu

AV Menu, continued

An on-screen slider displays when making some audio
and video adjustments. Numeric values represented on
the slider range from 0 (minimum) to 63 (maximum), with
31 as the mid-point.

AV Menu Options
Video Mute

On, Off

•

Global

•

The AV menu contains sub-menus for audio and video
adjustments
Audio Only
Screensaver

AV Menu Options

Video

On, Off

•

See the description of video adjustments on page 40.

On: Displays a solid blue background when there is
no video signal from the current input.
Use the On setting to let the colored screen remind
you that the TV is powered on at times when there is
no picture. The TV will power off if it detects no video
signal for five minutes.
Off. The screen appears black if there is no video
signal from the current non-antenna input.
On: Select On to display a random screensaver
pattern while playing an audio-only device. The
device must be named CD/Audio or MP3 Player to
use this feature.
Off: No screensaver pattern displays during play of
an audio-only device.

When playing an audio-only device, the TV will power off
after 12 hours of inactivity.
Audio

See the description of audio adjustments on page 42.
•

Reset

PerfectColor

•

To reset audio and video adjustments for the current input only, highlight the Reset icon
and press ENTER.
Reset has no effect on settings for Balance, Listen To, Language, and Film Mode.

PerfectColor Sliders

Adjust the saturation (intensity) of six colors for the
current image source.

PerfecTint Sliders
(246 Series TVs)

Adjust six hues for the current image source

To use PerfectColor and PerfecTint:
Highlight the PerfectColor™ icon and press ENTER to display the PerfectColor menu. Settings
are retained in memory independently for each TV input.
to move from one color bar to the next.
• Press
• Press
to change settings.
• Press CANCEL to restore default settings.
• Press MENU to return to the Main menu.
• 246 Series TVs. To switch between PerfectColor™ and PerfecTint™ adjustments, highlight Adjust Mode and press
.

Film Mode
(480i and 1080i
signals only)

Auto, Off

In Auto, the TV automatically detects and applies filmdecoding correction to movies filmed at 24 frames per
second. Try the Off setting if images show many jagged
edges.

Smooth 120
Film Motion
(148 Series TVs)

Standard,
High, Off

•
•
•

Smooth 120
Film Motion
(246 Series TVs)
Smooth 120
Demo

Standard: Removes judder (image vibration) and
smooths motion scenes in film-based content such as
movies.
High: Removes more judder in motion scenes in
movies.
Off: Use this setting if Standard or High cause noise.

Removes judder (image vibration) and smooths motion scenes in filmbased content such as movies.
1. Highlight the icon and press ENTER to display an adjustment screen.
2. Press
to change the amount of correction or set to zero to turn off
the correction.
3. Press EXIT to return to normal TV viewing.
Off, On

On displays two screens that demonstrate the benefits of
the enhanced processing provided with your Mitsubishi
TV. Note that 120 Hz processing makes any moving
image appear smoother, while Smooth120 Film Motion
is specifically for smoothing film-based content such as
movies.
Press any key to clear the demo or wait a few moments for
the demo screen to close.

Blue Glow
(246 Series
TVs)

On if TV off,
On if TV on,
Off

Select one of the On settings to see decorative blue lighting on the TV.

5. TV Menus

Video Menu

Video Menu, continued

Mitsubishi recommends you assign names to TV inputs before
making video adjustments (use the Inputs > Name menu).
Otherwise, adjustments will be reset to the defaults if you
name inputs afterwards.
To make video adjustments:
• From the Video menu:
1. Press
to highlight an option.
2. Press
to display the submenu and adjust.
3. Press MENU to return to the AV menu.
• While watching TV: Press the VIDEO key repeatedly to
display the video option you want to change. Press
to change settings.

Video Menu Options
SharpEdge
(246 Series TVs)

On, Off

SharpEdge™ adds special edge enhancements to make the image appear
sharper. Saved by input.

DeepField
Imager
(246 Series TVs)

DeepField™ Imager dynamically enhances black levels in portions of the screen
to provide strong contrast with detail over mixed screen content.

Off

Contrast is adjusted uniformly across the entire screen.

Demo

For comparison, displays a split picture to show On (right side) and Off (left side).

AV menu, Video options

Video Menu Options
Picture Mode

Brilliant

For use under bright light; unavailable when
the current input is named Game or PC.

Game

Optimizes picture and video processing
for gaming consoles. Available only when
the name of the input is Game or PC.

Bright

For most daytime viewing and x.v.Color
sources

Natural

For most nighttime viewing and x.v.Color
sources

Set the Picture Mode first before
changing other video settings, as
some settings are stored independently for each Picture Mode. Use
Picture Modes to get the best image
under different viewing conditions.

Contrast

•
•
•
•
•

Adjusts the white-to-black level
Settings are stored independently for each Picture Mode.
Low contrast shows a variety of shades in darker images
In most home lighting situations, medium contrast looks best.
High contrast shows darker images more uniformly black and makes colors appear more
vibrant. High contrast is good for brightly lit environments.

Brightness

•
•

Adjusts overall picture brightness
Settings are stored independently for each Picture Mode.

Color

Adjusts overall color intensity from no color to fully saturated.

Tint

Adjusts the red-to-green ratio.

Sharpness

Adjusts picture detail and clarity.

Color Temp

Adjusts the white balance. Settings are stored independently for each Picture Mode.
High

Gives white images a cool cast. May provide the most realistic picture under bright
lighting.

Low

Gives white images a warm cast. Natural/Color Temp at the low setting displays
video at approximately the 6500K industry standard for NTSC pictures.

Video Noise

High,
Medium,
Low, Off

Reduces minor noise (graininess) in the picture. Use Low with good-quality signals. Use
High with poor-quality signals. Use Off to leave the picture unaltered. Saved by input.
Depending on the setting for Smooth 120 Film Motion, not all settings may be available.

Backlight

Adjusts peak brightness of the backlight. Factory default is maximum brightness.

Vert Adjustment
(Stretch Plus
format mode only)

•
•

Press the ENTER key to enter adjustment mode (in Stretch Plus only).
Press
to move the picture up or down.

Horiz position
(Computer
image only)

Press

to display the adjustment slider. Press

to shift the image horizontally.

Vert position
(Computer
image only)

Press

to display the adjustment slider. Press

to shift the image vertically.

5. TV Menus

Captions Menu

Audio Menu
To make audio adjustments:
• From the Audio menu:
1. Press
to highlight an option
2. Press
to display the submenu and adjust.
3. Press MENU to return to the AV menu.
• While watching TV: Press the AUDIO key repeatedly
to display the audio option you want to change.
to change settings.
Press

Subwoofer
(246 Series TVs)

AV menu, Audio options

Turns on the internal TV speakers.

AV Receiver

Turns off the TV speakers so you hear sound only from a connected A/V receiver.
Note: When you disconnect an analog A/V receiver, be sure to manually change the Speakers setting to TV to hear sound from the TV speakers.

[Volume
adjustment]

The Subwoofer option displays only if a subwoofer connection has been identified on the SUBWOOFER OUTPUT jack. The setting is applied to all TV inputs. Use Off to turn off audio to a
subwoofer or to reset the AVR AUDIO OUTPUT jack. See reset instructions on page 16.
Highlight Subwoofer and press ENTER to display an adjustment slider for subwoofer volume.

Bass

Controls volume of low-pitched sound from the TV speakers.

Treble

Controls volume of high-pitched sound from the TV speakers.

Balance

Controls audio balance between the right and left TV speakers

Sound Mode

Normal

No special audio effects from the TV speakers

Expand

Modifies audio from the TV speakers.
•
For monaural (non-stereo) programs, creates a simulated stereo effect.
•
For stereo programs, creates a simulated surround sound effect.

Stereo

Default setting. The TV plays stereo broadcasts in stereo and mono broadcasts in mono. The word
Stereo is displayed when you tune to a channel broadcasting in stereo.

Listen To
Available for
analog channels from
ANT1/ANT2 or
an analog VCR
recording.

Language

Level Sound

Mono

Reduces background noise. Use when receiving a weak stereo audio signal. All audio is
played as mono with this setting.

SAP
(Second Audio
Program)

Selects an additional monaural sound track not audible during normal TV viewing. The SAP
signal might be related to the program (such as a sound track in a foreign language), or it might
be unrelated (such as a weather report). If an SAP signal is broadcast, the letters SAP are
displayed when you tune to the channel

English, French, Selects the current language for a digital program from ANT1 or ANT2. Each digital program
German, Italian, may include zero to seven language choices.
Portuguese,
Available for digital channels from ANT1/ANT2 only
Spanish, Other
On, Off

The TV can decode captions from ANT 1/ANT 2 and the
VIDEO composite and S-VIDEO jacks. Broadcasters can
send either standard closed captions or text service. Standard closed captions follow the dialogue of the program and
display in a small section of the screen. Text-service closed
captions often contain information such as weather or
news and cover a large portion of the screen.
•

The Speakers option displays only if an A/V receiver connection has been detected. The setting you select is
applied to all TV inputs.

Off, On

Captions on Digital Channels

Captions on Analog Channels

Audio Menu Options
Speakers

Reduces differences in sound volume between programming segments, such as the difference
between regular broadcast programs and commercial segments.

•

IMPORTANT
Analog text-service options display a large
black or gray box on the screen when no signal
is being broadcast.
The content of captions is determined by the
broadcaster. If captions show strange characters, misspellings, or odd grammar, it is not a
malfunction of the TV.
Closed caption signals are not available through
HDMI or component jacks. See the menus for
these devices for closed-caption decoding.

The TV can decode captions from ANT 1/ANT 2 only.
Broadcasters can send up to six different captioning
selections or can send analog captions that match those
sent by the analog station. A TV station may broadcast
only one or two types of captions or none at all.

Digital Settings menu. Check the caption test area
(upper right) to see how custom settings look.

Captions Menu Options
Analog
Captions

On if Mute
CC 1–CC 4
Text 1–Text 4
Off

•

Analog
Background

Gray, Black

Selects either a gray or black text background to make analog
closed captions easier to read.

Digital
Captions

On if Mute
Caption 1–
Caption 6
Off

•

Font

Default
Font 1–Font 7

Default changes settings to those selected by the captions provider, or, if none, to the TV’s own captions defaults. Use Fonts 1
through 7 to give captions a custom appearance.

Font Size

Large
Standard
Small

Large is the recommended size.

Font Color

White, Black, Magenta, etc.

Font Opacity

Translucent, Opaque, Flashing,
Transparent

Background
Color

White, Black, Magenta, etc.

Background
Opacity

Translucent, Opaque, Flashing,
Transparent

Closed
Captions

Digital
Settings

•
•

•

On if Mute: Displays analog closed captions signal CC 1
when audio from the TV speakers is muted. When watching
TV, press MUTE to turn captions on/off.
CC 1–CC 4: Standard closed-caption signals
Text 1–Text 4: Text-service signals

On if Mute: Displays digital closed caption signal Caption 1
when audio from the TV speakers is muted. When watching
TV, press MUTE to turn closed captions on/off.
Caption 1–Caption 6: Caption signals sent by the broadcaster

Guidelines for setting digital captions:
• A white font on a black translucent
background makes an easy-to-read
combination.
• Use contrasting colors for captions and
background.
• Check readability of captions using the
sample text in the upper right corner of
the menu.

5. TV Menus

Setup Menu

Setup Menu, continued

Use the Setup menu to:
• Select English or Spanish for menus and on-screen
text.
• Scan the channels available for the antenna or cable
service connected to the ANT 1 or ANT 2 jacks.
• Edit channel options, including channel locking.
• Set the TV’s internal clock.
• Set the TV Timer to turn on the TV automatically at
a designated time.
• Set the energy mode for power consumption when
the TV is powered off.
• Play the GalleryPlayer demo and get a
GalleryPlayer setup key.

Edit
Virtual Channel Number (digital channels only). A channel
number sent by a local broadcaster. Usually the virtual
number is associated with the corresponding analog
channel number. For example, a broadcaster may associate digital channel 2-1 with their analog channel 2.
Physical Digital Channel Number. The channel number
officially assigned to the actual broadcast frequency; shown
on screen in parentheses.
Setup menu, Scan option

Setup Menu Options

Language

Scan

Ant-1 Air
Ant-1 Cable
Ant-2 Air
Ant-2 Cable

Display on-screen menus in either English or Spanish.
Note: To listen to audio in other languages (when available), see the section
on the AV menu, Audio submenu, and refer to either Listen To > SAP (analog
signal) or Language (digital signal).
Scan memorizes broadcast channels to make them easier to find. To start
channel memorization:
1. Highlight one of the input selections based on your connection to ANT 1
or ANT 2:
• Air when connected to an indoor or outdoor antenna.
• Cable when connected to direct cable (no cable box)
2. Press to highlight START.
3. Press ENTER to start channel memorization for the selected input.

Notes on Scan and channel memorization:
• Channel memorization may take up to 15 minutes
to complete.
• To stop channel memorization before completion,
press CANCEL.
• When watching TV, press CH
to move through
memorized channels.
• To add a digital channel that does not appear in the
Edit menu without repeating channel memorization:
1. Look up the physical channel number
for the new digital channel. The website
www.antennaweb.org can help you find the
physical channel number.
2. Tune to any channel on the Ant 1 or Ant 2
input your antenna is connected to.

3. Use the number keys and CANCEL key to enter the
physical channel number followed by “-1” and ENTER.
For example, for physical channel 36, press
—
3 6 CANCEL 1 ENTER.

•

The TV will search for a digital channel on the
channel 36 frequency. When it finds the channel, it
will:
a. Add the channel to memory.
b. Change the channel number to the virtual
channel number sent by the broadcaster.
c. Add to memory any associated sub-channels.
Rememorize channels if you move the TV to a
different geographic area with a different channel
line-up.
If using TV Guide Daily, the channels displayed and
their order are independent of the TV’s channel memorization. Refer to Appendix D for more information.

Setup menu, Edit channel options

Setup Menu Options

Edit

English
Spanish

Use the Edit menu to edit channel options when ANT 1 or ANT 2 is the current source,
To highlight a channel number to edit:
• Press CH
/
to jump to the next page of channel numbers. Press and hold CH
/
to speed
through pages.
• Press
to move through all channel numbers, one at a time. Press and hold
to speed
through channel numbers.
The TV tunes to the highlighted channel on release of CH
/
or
.
Channel

Channels marked with a check are in memory. To add or delete a channel from
memory, highlight the channel number and press ENTER. To add a single digital channel
not in the list, see the notes under Scan on the opposite page.
Digital channels are listed by virtual channel number with the physical channel number
shown in parentheses.

Name

Assign a custom name up to six characters long to memorized channels. You can
name analog channels and digital channels if broadcast without pre-assigned names.
1. With the cursor in the Name field, press a number key repeatedly to cycle through
the characters associated with the key, including !, &, blank (1 key) and /, *, - (0 key).
2. Press ENTER to set the letter and move to the next letter position. To delete the
current character and move back one position, press CANCEL.

Fav1–Fav6

Use the six Fav channel banks to store groups of your favorite channels. For example,
you can set up a Fav channel bank for each of your favorite program types (e.g., sports,
news, children’s programs) or set up a bank for each TV user.
to move the highlight through the Fav area of the screen.
• Use
• Press ENTER to insert a check mark to add the highlighted channel to one of the Fav
banks.
• The same channel can be added to multiple Fav banks
• To remove a channel from a Fav bank, highlight the check mark and press Enter.
Note: To set up Fav channel banks without using this menu, see “Fav (Favorite Channels)” on page 33.

Lock

Lock channels so that a pass code is required to view them. When you rememorize
channels, all lock settings are cleared.
Highlight the Lock column and enter a pass code when prompted. If you previously
set a pass code to open the main Lock menu, use the same pass code. See “Lock
Menu,” page 51 for more on pass codes.
To lock or unlock a channel, highlight the lock icon for the channel and press Enter to
switch between the locked and unlocked versions of the icon.

5. TV Menus

Setup Menu, continued

Setup Menu, continued
Timer
Use the Timer to set a time for the TV to turn on automatically. Use this menu to set a day, time, input, and
channel for the Timer. If the TV is already on at the
requested time, the TV will automatically tune to the
designated channel.

Clock
Use either the manual or auto method to set the clock.
Set the clock if you wish to:
• Use the TV’s Timer function.
• Maintain accurate ChannelView listings.

•

246 Series TV. If you have enabled the TV Guide Daily
system, there is no need to set the clock; settings are
grayed out and unavailable.

•
Setup menu, Clock options

Setup Menu Options
Settings
Clock

•
•

Manual. To set the clock manually:
1. Select Manual.
2. Set the time of day.
3. Set the date.
4. Select your time zone.
5. Select either Applies or Ignore for Daylight Savings Time.
Note: If using Manual, each time the time change occurs, you must open this
menu and set the TV’s clock ahead or back.
Auto. To set the clock automatically:
1. Select Auto.
2. Select your time zone.
3. Select either Applies or Ignore for Daylight Savings Time.
4. After exiting the menus, tune the TV to an analog station on ANT 1 or ANT 2
carrying XDS data, typically a PBS station.
Note:
• With the Auto setting and Applies selected for Daylight Savings Time, the TV’s
clock adjusts automatically to daylight savings time.
• The TV’s clock will be reset if you tune to a channel sending incorrect time
data. To prevent unwanted clock resets, first use the Auto method to set
the clock from a channel sending the correct time, then change the method
to Manual.

Time
(Manual
option only)

1. With the hour highlighted, press
repeatedly to change the hour and the
AM/PM indicator. Press and hold to change the hour display quickly.
2. Press ENTER to set the hour.
3. With the minutes highlighted, press
to change the minutes. Press and
hold to change the minutes display quickly.

Date
(Manual
option only)

1. With the month highlighted, press
2. With the day highlighted, press
3. With the year highlighted, press

Time Zone

Eastern, Central,
Mountain,
Pacific, etc.

Required for both the Manual and Auto methods.

Daylight
Savings
Time

Applies
Ignore

Required for both the Manual and Auto methods. Select
the option for your area.

to select. Press ENTER to set.
to select. Press ENTER to set.
to select the current year.

•

The TV clock must be set before you can use the
Timer feature.
TV Energy Mode must be set to Fast Power On to
have the TV power on at the set time.
To open the Timer menu, highlight the Timer icon
in the Setup menu and press ENTER.
When the Timer turns on the TV, press any key on
the remote control to keep it on. Otherwise, the TV
will turn off after five minutes.
The POWER indicator on the front of the TV flashes
slowly when the TV is off to indicate the TV Timer
has been set to turn on the TV automatically.

Setup menu, Timer options

Setup Menu Options

Timer

On, Off

Day

Daily, Mon-Fri, (every) Sunday, (every) Monday, (every) Tuesday, etc.
Select the day or days of the week for the Timer to turn on the TV.

Time

To set the time for the TV to come on:
repeatedly to change the hour and the AM/
1. With the hour highlighted, press
PM indicator. Press and hold to change the hour display quickly.
2. Press ENTER to highlight the minutes.
3. Press
to change the minutes. Press and hold to change the minutes display quickly.

Input

Ant-1, Ant-2, DVD, VCR, etc.
Select the input you want displayed when the TV comes on. Choose from the defined
and enabled inputs that appear in the Input Selection menu.

Channel

If the input is an antenna (ANT 1, ANT 2), enter a channel number in any of three ways:
• Enter the number using the remote control’s number keys.
• Press
repeatedly
• Press and hold
to scroll quickly through the available channel numbers.

5. TV Menus

Setup Menu, continued

Setup Menu Options
Energy
Mode
Energy

Demo Mode
Fast Power On

Low Power

Use the Energy Mode option to select the level of
power consumption while the TV is turned off.
The default setting is Fast Power On.
Low Power uses less energy, but TV poweron takes longer and some TV features may be
unavailable.

Off, On

•
GalleryPlayer
Setup Key

CREATE/
EXPORT

•

Keep Energy Mode set to Fast Power On if you need to:
• Have faster power on.
• Receive updates to ChannelView channel listings.
• Keep the TV Clock accurate for the TV Timer. With the Low Power setting, you must reset the
TV Clock if the TV is left turned off for over 48 hours.
• Use the External Controller Input Wired IR option (see page 10).
• 246 Series TV: Receive updates to TV Guide Daily listings.
• 246 Series TV: Receive CableCARD program updates.
Note: 246 Series TV: TV Guide Daily and CableCARD require the Fast Power On setting. If you
activate TV Guide Daily or use a CableCARD, the TV will automatically override a Low Power setting
and change to the Fast Power On setting.

•

Select On to begin play of the sample GalleryPlayer images
included with the TV.
Press any key on the remote control or TV control panel to
end the demo.
Highlight CREATE and press ENTER to create a setup key and
save it to your USB storage device. You only need to create
the key once.
Highlight EXPORT and press ENTER to save a previously
created setup key to your USB storage device.

Note: You must save the setup key to each storage device on
which you save GalleryPlayer images.

Getting Started with GalleryPlayer
Use the TV’s GalleryPlayer Demo Mode to see sample
images included with the TV. Press any key on the
remote control to end the demo.
To get more images, you will need:
• A USB-connectible storage device. The device
can be a USB drive or a memory card inserted
into a USB-connectible card reader.
Note: The device must use the FAT/FAT32 file
system.
• A setup key generated by the TV.
• A computer on a high-speed internet connection.
Getting a Setup Key
If you wish to purchase more images, you must first
get a setup key from the TV.
1. Plug your USB storage device into the TV’s USB
photo port and wait for the TV to switch to it.
2. Press MENU and then open the TV’s Setup >
GalleryPlayer menu.
3. Highlight CREATE and press ENTER. The TV will
save a setup key to the storage device.
4. Unplug the USB device from the TV.

Getting Images
1. Use your computer’s high-speed internet connection to go to Mitsubishi.GalleryPlayer.com where
you can purchase and download collections of
images.
2. Plug the USB storage device into your computer
and download the images to the USB device.
Viewing Images
1. With the TV powered on, connect the USB storage
device to the TV’s USB jack.
2. If your USB device contains GalleryPlayer
images and your own photos, a menu will display
to let you choose which to view. Highlight
GalleryPlayer.
3. The TV’s USB Photo menu will open.
4. With the Slideshow icon highlighted, press ENTER
to start viewing images.
For more on use of the USB Photo menu with GalleryPlayer images, see “Viewing Camera Files and GalleryPlayer Images,” page 35.

5. TV Menus

Lock Menu

Inputs Menu
Inputs Menu Options

Name

TV locks available from the Lock menu are:

Cable Box, Camcorder, CD/
Audio, DVD (DVD, DVD2,
Blu-Ray), DVR, Game (Game,
PS, Xbox, Wii), MP3 Player, PC,
Satellite, VCR, AVR
On/Off (Ant 1 and ANT 2 only)
Delete (deactivated HDMI only)
Control On, Control Off (CECenabled HDMI devices; operates
only when Inputs > NetCommand
HDMI Control is set to On)

•

•
•
•

Lets you assign or change names of inputs appearing in the
Input Selection menu.
-- Press
to move between inputs.
-- Press
to select a name.
Lets you turn Ant-1 and Ant-2 On/Off (to display/hide in Input
Selection menu).
Lets you delete unused HDMI inputs from the Input Selection
menu.
If you change the name of an input after performing NetCommand “learning,” the IR codes you “learned” are erased.

General Notes
When you change an input name in the Name menu and then exit the Name menu:
• The name is changed
• The icon in the Input Selection menu is changed
• Audio and video settings are changed to the defaults for the new device type.
• All previous NetCommand “learning” for the input is erased.
Notes for HDMI devices
• Disconnecting an HDMI device: When you disconnect an HDMI device, the icon remains in the Input Selection
menu until you remove it. Select Delete in the Inputs > Name menu to remove an unwanted icon for an HDMI input.
• NetCommand for HDMI and CEC-Enabled Devices: If CEC conflicts occur, turn off CEC signals in one of
these ways: a) Turn off all NetCommand for HDMI signals from the TV (Inputs > NetCommand HDMI Control
menu), b) Turn off NetCommand HDMI signals for specific devices (Inputs > Name menu), or c) Turn off each
device’s internal CEC capability. See Appendix E for the TV’s NetCommand for HDMI Control or, to turn on/off
a specific device’s response to CEC signals, see the device’s owner’s manual.
• Names of CEC-enabled devices: CEC-enabled devices send their own predefined name to the TV. You
cannot change the name of a CEC-enabled device; applies only when Inputs > NetCommand HDMI Control
is set to On.

Order

Learn

Lets you put frequently used icons at the start of the Input Selection menu.
1. Press
to highlight the icon to move.
2. Press ENTER to confirm the selection.
3. Press
to drag the icon to the desired position.
4. Press ENTER to set the new position.
Sets up or changes NetCommand IR control of the current viewing device.
See detailed instructions in chapter 6, “NetCommand IR Control.”

Parent

Other

Time
Control
Panel

Note:

Lock by Ratings
Restrict access to programming
based on V-Chip rating signals sent
by the broadcaster.
Lock by Time
Restrict TV use by time of day.
Lock Control Panel
Disable the buttons on the TV’s
control panel. Use this option if
small children in the home try to
press control-panel buttons.

Channel Lock is an additional lock that blocks
access to specific channels. Channel Lock is
available under the Setup menu (Setup > Edit
> Lock, page 45).

Pass Codes
Setting a Pass Code
You are prompted to enter a pass code whenever you
select Lock on the Main menu. To set a pass code for
the first time:
Press MENU, highlight Lock, then press . A screen
prompting you for a pass code will display.
2. Input a four-digit pass code using the number keys
on the remote control.
• Press CANCEL to delete a number and move back
one space.
• Press MENU or EXIT to close the menu without
setting a pass code.

3. Press ENTER to set the pass code.
Resetting a Pass Code
See the procedure in Appendix B.

AVR

Sets up NetCommand IR control of an A/V receiver.
See detailed instructions in chapter 6, “NetCommand IR Control,” starting on page 60.

NetCommand
HDMI Control

Guide, Devices, Zip
Code

246 Series TV. See Appendix D for the TV Guide Daily system.

On, Off

Select On or Off to enable or disable the TV’s control of all CEC-enabled
devices. See Appendix E for details.

•

To turn CEC on or off for individual devices, use the Inputs > Name
menu.

The Lock > Parent menu lets you set parental controls
using V-Chip technology.

Parent Menu
The TV comes from the factory with the rating locks
turned off and with pre-set U.S. ratings TV-PG and
movie rating PG. Turn on blocking for U.S. ratings
to activate these rating restrictions. Use the Lock >
Parent menu to change the level of blocking with U.S.
ratings.
Any time you change the channel or device, it may take
up to five seconds for the rating restrictions to take
effect.

Other Menu (Alternate Rating System)
This TV can recognize new rating systems that may
come into effect in the future. The Other menu allows
you to block digital programming when such systems
come into effect.
The first time you tune to a channel broadcasting an
alternate rating system, the TV defaults to the most
restrictive setting if the Lock menu > Other Lock
option is set to On. Use this menu to change the
allowed rating if you are unable to watch a program
broadcast with an alternate system.

Bypassing TV Locks
•

•

Guide

•

Important Notes on Rating Locks
Parent menu rating locks apply only to channels
and signals received on ANT 1, ANT 2, and the
VIDEO composite and S-VIDEO jacks.
Other menu rating locks apply only to digital channels received on ANT 1 or ANT 2.
When viewing a cable box, satellite receiver, or
other device connected to the component Y Pb
Pr or HDMI inputs, check the device’s owner’s
guide for use of parental locks.

•

If you try to watch a blocked program or channel,
or the TV is locked by time, a notice will appear
prompting you for a pass code. To use the TV,
input your four-digit pass code and press ENTER.
-- To reactivate the locks after using a pass code,
power the TV off and then on.
-- To reactivate only the parent ratings lock,
change to a different channel or device.
If a program or channel is blocked, you can still
use the TV without entering a pass code. The lock
allows you to change to a channel airing an allowed
program or change to another device.

5. TV Menus

Lock Menu, continued

Other Menu Options (alternate rating system)

Parent Menu Options (U.S.-based rating system)
Option Name and Description
Lock

Off, On

Disables or enables program blocking based on V-Chip signals and the U.S. rating system.

TV
Rating

TV-Y

Youth. For children under 7.

TV-Y7

Youth 7 and older.

TV-G

General Audience. For the entire family.

TV-PG

Parental Guidance. Parental Guidance recommended; may
not be suitable for some children.

TV-14

Adolescent 14 and older. Not recommended for children under 14.

TV-MA

Mature Audience. For adults only.

Highlight the rating level
you wish to change and
press ENTER to block it
( ) or allow it ( ).
You can apply supplemental content blocking
to the age-based ratings
by using the TV content
categories listed below.

Fantasy Violence. Applies to TV-Y7 only.

Sexual Dialog. Applies in differing degrees to TV-PG and TV-14.

Adult Language. Applies in differing degrees to TV-PG, TV-14, and TV-MA.

Sexual Situations. Applies in differing degrees to TV-PG, TV-14, and TV-MA.

Violence (graphic or realistic). Applies in differing degrees to TV-PG,
TV-14, and TV-MA.

Movie
Rating

General Audience. Designed for the entire family to view.

Parental Guidance. Parental Guidance is recommended, may not be suitable for some children.

PG-13

Parental Guidance, 13 and Older. Not recommended for children under the age of 13.

Restricted. Restricted in theaters to 17 years old and older unless accompanied by an adult.

NC-17

No Children 17 or Under. Restricted in theaters to 18 years old and older.

Adult. Designed for and restricted in theaters to adult audiences only.

Not Rated
Start
Time
Stop
Time

This TV can recognize new rating systems that may come into effect in the future. The Other option remains grayed
out until the TV receives a signal using an alternate rating system. Such alternate rating systems will apply only to
digital programming received on the ANT 1 and ANT 2 inputs.
Option Name and Description
Lock

On, Off

System Name

The rating system available for the channel

Group

Rating groups available in the rating system shown on the screen. Rating groups are defined by
the rating system in effect.

Rating

Rating restrictions available in the selected rating system and group. Highlight the rating and
press ENTER to check (block) or uncheck (allow) rated content.

Enable or disable program blocking.

Time
TV Content
Categories

The program has not been assigned an MPAA rating.

Allows you to set the time of day for enforcement of rating restrictions set in the Parent menu.
1. Highlight the hour digits for Start Time.
repeatedly to change the hour and associated AM/PM indicator. You can also just press
2. Press
and hold to move quickly through the numbers.
3. Press ENTER to highlight the minutes.
4. With the minutes digits highlighted, press
repeatedly to change the minutes. You can also just
press and hold to move quickly through the numbers.
5. Highlight the Stop Time digits and set the time as described above.
Note:

To make rating restrictions active 24 hours a day, make Start Time and Stop Time the same.

Blocks all use of the TV during the time period you specify. You must enter a pass code to use the TV when the time
lock is in effect.
Lock by Time

On, Off

Lock Time,
Unlock Time

To set the lock and unlock times:
1. Highlight the hour digits for the Lock Time.
repeatedly to change the hour and associated AM/PM indicator. To move quickly
2. Press
through the numbers, just press and hold.
3. Press ENTER to set the hour and highlight the minutes.
4. With the minutes highlighted, press
repeatedly to change the minutes. To move quickly
through the numbers, just press and hold.
5. Highlight the Unlock Time digits and set the time as described above.
Note:

Enable or disable Lock by Time.

To make Lock by Time active 24 hours a day, make Start Time and Stop Time the same.

Control Panel
On, Off

On locks and Off unlocks the buttons on the TV’s control panel. Use this option if small children
may try to press TV buttons.
• If the remote control is unavailable, use the TV’s control panel to release the Control Panel
Lock. Press and hold the MENU button for over eight seconds.
• If the TV is powered off, release the lock as described above. The TV will power on.
• To reactivate the lock, you must return to this menu and change the setting to On.

NetCommand IR Control

•
•
•

•

To learn about NetCommand for HDMI devices,
see Appendix E and “About Home-Theater Control Systems,” page 17.
NetCommand setup is optional.
You may wish to use NetCommand IR control to
supplement CEC control.
You can perform NetCommand setup when the TV
first recognizes a device during Auto Input Sensing
or at any convenient time afterward.
NetCommand operates by sending remote control
signals from the TV to your other devices via the IR
emitters, telling the devices to play, record, change
inputs, adjust volume, change channels, or perform
other functions. All this is accomplished with the
TV’s remote control and the slide switch left in the
TV position.
The IR “Learning” feature of NetCommand allows
the TV to learn the IR control signals for your A/V
devices.

Important Note on NetCommand
Be sure to connect the IR emitter cable to the
TV and properly place the emitters so that
NetCommand can control your devices. See
the explanation on the opposite page.

*3TFOTPS
*3TFOTPS

IR Emitter Placement
An IR emitter cable is included with the TV.

HDMI

The NetCommand system uses emitters connected
3
*3TFOTPS
to the IR—NetCommand Output jack to control other *OGSPOU TIBSFECZUXP
BWFSBHFTJ[FEEFWJDFT
devices such as DVD players, cable boxes, satellite
2
*3TFOTPS

receivers, and VCRs.
"73FDFJWFS
1. Connect the plug end of the supplied IR emitter
1
cable to the IR—NetCommand Output jack on the
*OGSPOUPGB TV main panel.
*3TFOTPS
You can choose the level of NetCommand
control
TJOHMFBWFSBHF
for your home theater.
2. Run the cable for each of the emitter ends under,
TJ[FEEFWJDF
Standard Setup. Perform a standard setup if
alongside, or over each device to be controlled so
you want NetCommand to control only a few
that the emitter end is in front of the area where the
IR- NetCommand

Output / External
devices, such as the TV, a playback device (like
remote control sensor is located.
Controller Input
a DVD player), and a cable box. With this setup,
3. Position the emitter end with the emitter bulb facing
you can use the TV’s remote control to operate *3TFOTPS
the remote control sensor. The bulb emits infrared
these devices.
light in a cone-shaped pattern. Place the bulb far
57#BDL1BOFM
A/V Receiver Setup.0OUPQPGBTJOHMF
Perform A/V receiver
enough from the sensor to allow the cone pattern
setup if you want NetCommand
to:
to reach the sensor.
UBMMEFWJDF
Control a surround sound A/V receiver.
The IR sensor is usually behind the plastic window
of the front display panel. It is sometimes visible
Automatically change audio input selections
with the aid of a flashlight and is normally a round
on an A/V receiver when you change inputs
Connecting IR—NetCommand Output
or
square cutout behind the plastic.
on the TV.
If you cannot see the sensor and the device’s
Automatically change audio*3TFOTPS
and video input
*OGSPOUPGBTJOHMF
Owner’s
Guide does not specify the location, you
*3TFOTPS
selections on an A/V receiver with an HDMI
BWFSBHFTJ[FEEFWJDF
can
find
it
by
following
these
steps
using
the
output to the TV.
device’s remote control:
0OUPQPGBTJOHMF
*OGSPOU TIBSFE
*3TFOTPS
*3TFOTPS
*3TFOTPS
UBMMEFWJDF
a.
Hold
the
device’s
remote
about
one-half
inch
*3TFOTPS
CZUXPBWFSBHF
from
the
front
of
the
device.
Starting
from
one
TJ[FEEFWJDFT
*OGSPOU TIBSFECZ
*3TFOTPS
end of the display window plastic, press the
UXPBWFSBHFTJ[FE
POWER button.
EFWJDFT
b. If the device does not respond, move the
Place IR emitters so the signal can be “seen” by the IR
remote control one inch toward the center and
sensor on each device.
try again.
c. Repeat this until the device responds.
d. Note this location and then start over from the
other end of the display window plastic, repeating until the device responds again.
The remote control sensor is somewhere
between these two positions. This is usually
enough accuracy for placement of the IR emitters.
IMPORTANT
In some cases, the emitter works better facing
downward from the top of the device. ExperiPosition IR emitters so that each device’s
ment to find what works best.
sensor “sees” the signal from only one emitter.
Otherwise, a device receiving signals from
4. Secure the emitter ends in place using doublemultiple sources (remote controls, IR emitters)
sided tape.
may not respond at all.
5. Place any unused ends behind the devices to
prevent stray signals from reaching the IR sensors.
$)

% * ( * 5 " -

463306/%

•

0OUPQPGBTJOHMFUBMM
EFWJDF
0UIFS"7%FWJDF

About NetCommand IR Control
Note:

*3TFOTPS

6. NetCommand IR Control

IR- NetCommand

S-VIDEO

Output / External
Controller Input

INPUT3

(480i / 480p / 720p / 1080i)

*OGSPOUPGBTJOHMF
BWFSBHFTJ[FEEFWJDF

VIDEO

AUDIO
R

DVI/PC

Y / VIDEO

AUDIO

INPUT2

INPUT1

$)')4!,
!5$)/
/54054

!62 !5$)/
/54054

ANT2/AUX

ANT1/MAIN

6. NetCommand IR Control

Initial NetCommand Setup for Most Devices

NetCommand Specialized Device Keys

To perform this procedure, you need:
• The remote controls for both the TV and the
device you want to control.
• The IR emitter cable supplied with the TV.

Refer to this chart when “learning” device keys. “Learn”
some, all, or none of the keys used for each device
type. The chart has space for you to write in functions
you assign to the F1–F4 keys.

See the following page for more on keys marked in the
“Special Operation Method” column.

Note:

1.
2.
3.

To set up an A/V receiver, see “Setting Up
NetCommand Control of an A/V Receiver,” page
60.
Connect and position the IR emitters for the
devices you wish to control. See “IR Emitter Placement” on the previous page.
Set the TV’s remote control slide switch to the TV
position and power on the TV if needed.
Open the NetCommand Learn screen in one of two
ways:
• If working from the Auto Input Sensing screen
for the device, highlight the Learn icon and
press ENTER to open the Learn screen for the
device.
• If performing NetCommand setup at any time
after the device has been recognized through
Auto Input Sensing:
a. Press INPUT to open the Input Selection
menu.
b. Highlight the desired input icon and press
ENTER to switch to that input.
c. Press MENU, highlight Inputs, and highlight
Learn to open the Inputs > Learn screen
for the device.

From the Auto Input Sensing screen, highlight the Learn
icon and press ENTER to open the NetCommand Learn
screen.

Inputs > Learn screen

•

4. The first function highlighted in the Learn screen

is always Power On. Aim the TV’s remote control
at the TV and press ENTER to begin learning for that
function.
When the Power On text starts flashing, aim the
device’s remote control at the TV and press and
hold the POWER key until a check mark appears next
to Power On.
• If the text stops flashing before the check mark
appears, repeat the previous step.
• To remove the key from NetCommand control,
press the CANCEL key while the key name is
highlighted.
Press the
keys on the TV’s remote control
to highlight other keys on the list. Repeat steps
4 and 5 for each additional function you wish to
control through NetCommand.
If the device’s remote control has keys that are not
in the list, you can associate up to any four keys
with the F1 through F4 keys. Perform NetCommand
setup for the F keys the same way you did for the
named keys. For example, you can:
• Assign your DVD player’s CHAPTER SKIP FORWARD and
CHAPTER SKIP BACK keys to F1 and F2.

“Learn” your A/V receiver’s DSP options for the
current device.
If the device has a separate POWER OFF key, press
on the TV’s remote to highlight Power Off.
Repeat the earlier steps to “learn” the POWER OFF key.
If the device has no POWER OFF key, skip this step.
Press EXIT to finish NetCommand “learning” for the
current device.

Adding or Removing Device Keys
from NetCommand Control
1. Press INPUT to open the Input Selection menu, highlight the device’s icon and press ENTER.
Open the Inputs menu and highlight the Learn icon.

2.
3. When the Learn screen displays:
•

•

To add keys: Continue as described earlier
under “Initial NetCommand Setup for Most
Devices” on this page.
To delete keys: Highlight the name of the key
you wish to delete and press CANCEL on the TV‘s
remote control to clear the check mark.

Key Name in
Learning Screen

Function

Name on TV
Remote Control

Power On

Power On or Power ON/OFF (toggle)

POWER

Guide

On Screen Program Guide or DVD Disc Menus

GUIDE

Channel Up

Next Channel Higher

CH/PAGE

Channel Dn

Next Channel Lower

CH/PAGE

Page Up

Page Up in Guides

CH/PAGE

Page Dn

Page Down in Guides

CH/PAGE

*
*

Setup menu for device

Adjust Up

Adjust or arrow up

Adjust Dn

Adjust or arrow down

Adjust Lt

Adjust or arrow left

Adjust Rt

Adjust or arrow right

Enter

Enter or Select (menus)

ENTER

Cancel

Cancel or erase (menus)

—/CANCEL

Play

*
*

Start playback

Stop

Stop playback

Forward

Fast Forward

Rewind

Rewind/Fast Reverse

Pause

Pause playback

Record

Start Recording

1, 2, 3, 4, 5, 6, 7, 8, 9, 0

Digit functions

1, 2, 3, 4, 5, 6, 7, 8, 9, 0

Enter (digits)

Use after digits to directly access channels by
number

ENTER

- (separator)

Add digital channel separator between main channel
number and sub-channel number

—/CANCEL

Recall (QV)

Last Channel Recall

Info

On-screen status display or information display

INFO

ASSIGN YOUR
CHOICE OF
SPECIALIZED
FUNCTIONS

F1
F2
F3
F4
Power Off

Power Off

F1
F2
F3
F4
POWER

See Special
Operation
Method Table

*
*

May require two
keypresses

6. NetCommand IR Control

Operating NetCommand-Controlled Devices

Operating NetCommand-Controlled Devices, continued

Controlling Most Device Types

Controlling an A/V Receiver

As an example of NetCommand control, if you are watching your cable box and you wish to tune to the next
channel higher, press CH/PAGE . NetCommand then sends
the “learned” channel-up control signal to the cable box.
1. With an IR emitter properly positioned in front of the
device, use the Inputs > Learn screen to perform
NetCommand setup for the device.
2. When you wish to use the device, press INPUT to
display the Input Selection menu.
3. Press
to highlight the icon for the device.
4. Press ENTER to switch the TV to the device.

See page 60 to set up control of an A/V receiver.

Note: if you have set up automatic input switching for the
A/V receiver, the A/V receiver will automatically
switch to the correct input for the device.
5. To operate the device using the TV’s remote
control, set the slide switch to the TV position.
6. Point the remote control at the TV (not the device)
and press the key for the desired function.

Special Operation Methods

Switching Audio to and from the A/V Receiver

Key Name in
Learning Screen

Special Operation Description and Setup

How to Use

Guide

Displaying the Disc Menu (DVD or high-definition disc format)

While watching the device, press GUIDE to display
the disc menu.

1. Press AUDIO.
2. Press to show the Speakers option.
3. Press to select either AV Receiver or TV.

“Learn” the Disc Menu, Top Menu, or other key as
named on the original remote in the Guide learning position.
Displaying the On-Screen Program Guide
(cable box or satellite receiver)

Controlling A/V Receiver Power

1.
2.
3.
4.

Press AUDIO.
Press
to show the Speakers option.
Press to select AV Receiver.
Point the remote control at the TV (not the A/V receiver)
and press POWER to power the A/V receiver on or off.

Controlling Other A/V Receiver Functions
With the A/V receiver powered on and selected, the
TV’s remote operates the volume and mute functions.
Also, when you switch to a device in the Input Selection menu, the A/V receiver automatically switches to
the correct audio input for the device.

Key Name in
Learning Screen

Special Operation Description and Setup

How to Use

Power On

Manual Power On/Off
Use for devices that have only one POWER key.

1. Press INPUT to display the Input Selection
menu.
2. Press
to highlight the icon for the
device to be powered on or off.
3. With the Input Selection menu still displayed,
press POWER to send the power signal; you may
need to press POWER twice.
If you press POWER without the Input Selection menu displayed, the TV will turn
off.
4. Press ENTER to switch the TV to the device.

1. “Learn” the Guide key on the original remote in
the Guide learning position.
2. Learn the PAGE
and PAGE
keys of the
original remote in the Page Up and Page Dn
learning positions.
Page Up
Page Dn

Enter

Power Off

•
Automatic Power On/Off
This feature is only for devices that have separate
Power On and Power Off keys on their original remote
controls. If your device does not have a separate
Power Off key, do not use the Power Off learning position; use only the Manual Power ON/OFF
method described above.
In the NetCommand Learn screen:
a. “Learn” the Power On command in the Power •
On learning position.
b. “Learn” the Power Off command in the
Power Off learning position.
Displaying the Menu for a Device

To Power On the Device
1. Press INPUT to display the Input Selection
menu.
2. Press
to highlight the icon for
the device to be powered on or off.
3. Press ENTER to switch the TV to the device
and NetCommand will send the Power
On command to the device.

Inside the Guide
Press CH/PAGE
/
commands.

to send the Page Up/Dn

Outside the Guide
Press CH/PAGE
Dn signal.

to send the Channel Up/

Enter Functions (cable boxes, satellite receivers, etc.)
Some devices have two keys that have “enter” functions. One key is for menus and is often labelled
SELECT or OK. A second key is for use with number keys for direct channel selection. NetCommand
uses the same ENTER key for both operations.
1. Press MENU or GUIDE to display the device’s
menu or guide.
2. Press ENTER within the menu and
NetCommand will send the Enter signal for
menus.

Enter (digits) When ENTER is for channel changes, i.e., the original Press digit key(s) and then press ENTER.
remote control has a separate ENTER key for this
NetCommand will send the Enter signal for
function):
channel selection.
Learn the ENTER key for channel selection in the
NetCommand Enter (digits) learning position.
Use this learning position only if the original
remote control has separate keys for Enter in
menus and Enter for channel selection.
Cancel

CANCEL as the Cancel or Exit Function
“Learn” the Cancel or Exit function in the
NetCommand Cancel learning position

—
(separator)

The symbol “—” can serve as the separator
between a digital channel’s main and subchannel digits, e.g., digital channel 12-1 (main
channel is 12, sub-channel is 1).
“Learn” the channel separator function in the
NetCommand – (separator) learning position.

To Power Off the Device
When you turn the TV off, the TV sends all
learned Power Off commands to all devices.

1. While watching a device, press INPUT to display
the Input Selection menu with the device
icon highlighted.
2. Press MENU to send the menu signal to the
device. The Input Selection menu will automatically clear from the screen.

1. While watching the device, press GUIDE to
display the guide.
2. Press CH/PAGE
/
to send the Page Up/Dn
commands for the guide.

•
Using Page Up/Down
If the device’s original remote control has separate
keys for Channel Up/Dn and Page Up/Dn, the TV
/
key can work like
remote control’s CH/PAGE
•
the two separate keys.
1. “Learn” CHANNEL / in the Channel Up/Dn
positions.
2. “Learn” PAGE / in the Page Up/Dn positions.

When ENTER has a menu or guide function or when
the original remote control uses the same key for
menus and channel selection:
Learn the ENTER, SELECT, or OK key in the
NetCommand Enter learning position.

Note:

Power On

6. NetCommand IR Control

1. Press MENU or GUIDE to display the menu or
guide.
—
2. Press CANCEL and NetCommand will send
the Cancel or Exit signal.
—
Press digit key(s) and press CANCEL .
NetCommand will send the channel-separator
signal.

6. NetCommand IR Control

Setting Up NetCommand Control of an A/V Receiver

To perform this setup you need:
• The remote controls for both the TV and the
A/V receiver.
• The IR emitter cable supplied with the TV.

key on the TV’s remote control to highlight
other keys in the list. Repeat steps 2 and 3 for each additional function you wish to control through NetCommand.
If the A/V receiver has a separate POWER OFF key,
press on the TV’s remote to highlight Power Off.
Repeat steps 2 and 3 to “learn” the POWER OFF key.
When finished “learning” the power and volume
keys, either press EXIT to watch TV or leave the AVR
screen open to continue with NetCommand setup
to control switching of A/V receiver inputs.

Before You Begin

1. Connect your A/V receiver to the TV and any addi-

tional devices. See chapter 3, “TV Connections,”
for suggestions.
Connect the IR emitter cable to the TV and position
the IR emitter where it can send signals to the A/V
receiver. See “IR Emitter Placement,” page 55.
Set the TV’s remote control slide switch to the TV
position and power on the TV if not already on.

Audio Switching Setup 1

If using the Auto Output or Auto Input
Sensing screen for the A/V receiver, highlight
the Learn icon and press ENTER to open the AVR
screen.
• If performing NetCommand setup at any time
after the A/V receiver has been recognized
through Auto Output/Auto Input Sensing:
Press MENU, highlight Inputs, and highlight AVR
to open the AVR screen.
The first function highlighted in the AVR screen is
always Power On. Aim the TV’s remote control at
the TV and press ENTER to begin learning for Power
On.
•

%7%1MBZFS EJHJUBMTVSSPVOETPVOE
XJUI
%JHJUBM
4VSSPVOE
WJEFP
4PVOE

*ODPNJOH
audio output
from BVEJP WJEFP
$PBYJBM
TV (digital
or analog)
$BCMF

TV audio
out

DVD audio
WJEFP
input
TV audio input

•

%7%BVEJP
JOQVU
"73FDFJWFS

Audio Switching Setup 2: Audio from a device
providing surround sound is sent directly to the A/V
receiver.

A/V Receiver
Incoming Coaxial Cable
to ANT 1/ANT 2

Audio Switching Setup 1: A/V receiver audio from the
TV’s digital or analog audio output
•

IMPORTANT
To hear audio sent from the TV to the A/V receiver,
you must have:
• Physically connected the TV to the A/V
receiver.
• Assigned, if needed, the name AVR if using an
HDMI A/V receiver.
• Selected the A/V receiver as the audio source.
Press AUDIO, then
to show the Speakers
option, then to select the A/V Receiver.
• “Learned” the IR codes for the A/V receiver
inputs.
• Assigned the TV’s audio output to the correct
input in the NetCommand A/V Receiver Learn
screen.

Audio Switching Setup 2

VCR with
Analog Audio Output

Setup to Control A/V Receiver Power and Volume

1. Open the AVR screen in one of two ways:

ment. To switch both audio and video via an HDMI
connection, see page 64.
Audio Switching Setup 1: Automatic A/V Receiver
Switching to TV Audio Input
Audio Switching Setup 2: Automatic A/V Receiver
Switching to a device sending audio directly to the A/V
%7%1MBZFSXJUI
receiver. You must
use setup 2 to hear digital sur- EJHJUBMTVSSP
%JHJUBM4VSSPVOE4PVOE
round sound from the source device.

Two different setups are described here. Review the
descriptions to find the setup needed for your equip-

4. Press the

Perform this setup to operate the A/V receiver’s power
and volume functions with the TV’s remote control.

To set up control of an A/V receiver you need:
• The remote controls for both the TV and the A/V
receiver.
• The IR emitter cable supplied with the TV.
• Connecting cables

BOBMPHBVEJP

A/V receiver’s remote control at the TV and press
and hold the POWER or POWER ON key until a check mark
appears next to Power On.
• If the text stops flashing before the check mark
appears, repeat this step.
• To remove the key from NetCommand control,
press the CANCEL key while the key name is
highlighted.

Perform one of these setups to enable the A/V receiver
to switch automatically to the correct audio input when
you select a device in the TV’s Input Selection menu.

WJEFP

A/V Receiver Control: Power and Volume

3. When the Power On text starts flashing, aim the

A/V Receiver Control: Automatic Audio Switching

analog audio

To set up control of other device types, see
“Initial NetCommand Setup for Most Devices,”
page 56.

AVR screen. Perform
NetCommand IR
“learning” for A/V
receiver power and
volume keys.

video

Note:

Setting Up NetCommand Control of an A/V Receiver, continued

audio + video

Several types of A/V receiver control can be set up
using the Inputs > AVR menu, shown on the following
pages.
• Controlling power and volume is described on this
page.
• Automatic audio switching, suitable for most equipment setups, is described under “A/V Receiver
Control: Automatic Audio Switching” on the opposite page.
• Automatic audio and video switching can be set up
If your A/V receiver has an HDMI output. You can
send audio and video from multiple devices to the
A/V receiver and then through a single cable to the
TV. See “A/V Receiver Control: Automatic Audio
and Video Switching via HDMI,” page 63.

6. NetCommand IR Control

Audio Available from TV only
Audio from ANT 1 and ANT 2 must be sent to
the A/V receiver from the TV’s DIGITAL AUDIO
OUTPUT or analog AVR AUDIO OUTPUT.
Use Setup 1 to make the A/V receiver switch to its
designated TV audio input when viewing these sources.
Analog Stereo Audio
Audio from sources with only analog stereo output
(such as a VCR) can be sent either directly to the
A/V receiver or through to the TV and then on to the
A/V receiver.
Mitsubishi recommends you send audio through
the TV as shown in the example. Setup 1 causes
the A/V receiver to switch to its input designated for
TV audio.
If you have a digital A/V receiver, the TV makes the
audio available by converting analog audio to a
digital output.
HDMI Digital Stereo Audio
Digital stereo audio from an HDMI connection
is available both in digital format (from the TV’s
DIGITAL AUDIO OUTPUT jack) and in analog
format (from the TV’s AVR AUDIO OUTPUT jack).

Note: This setup is required to hear digital surround sound
A device can send digital surround sound such as
Dolby Digital or DTS directly to the A/V receiver,
bypassing the TV entirely. The device might be a DVD
player, cable box, or satellite receiver, and could have
HDMI output. A DVD player is used in this example.
Your setup may include additional devices with digital
surround sound connected directly to the A/V receiver.
These devices might be a DVD player plus a cable box
or satellite receiver.

6. NetCommand IR Control

Setting Up NetCommand Control of an A/V Receiver, continued

2.
3.

your A/V receiver to the audio outputs on the TV
and the DVD player. See chapter 3, “TV Connections,” for suggestions. Important: To use Setup
1, you must connect the A/V receiver to the TV’s
audio output; i.e., the TV’s AVR AUDIO OUTPUT or
DIGITAL AUDIO OUTPUT jack.
Position NetCommand IR emitters as described in
“IR Emitter Placement,” page 55.
Open the Inputs > AVR menu.

Note:

The terms Input1–Input5 used in the AVR menu
are names used by the TV to uniquely identify
A/V receiver inputs.

Audio Switching Setup 2: Automatic A/V Receiver
Switching to a Surround
Sound Device
%7%1MBZFSXJUI

Most devices are set up like the VCR in this example, in
which analog audio from the device is sent through the TV.

Use this setup to send digital surround sound directly
from a device to an A/V receiver.
1. Under Learn, highlight Input2.
In this example, the IR code for the A/V receiver’s
DVD Audio input will be “learned” as Input2.
2. Press ENTER on the TV’s remote control.

1. Under Learn, highlight Input1.
2.
3.

B
D

In this example, the IR code for the A/V receiver’s
TV Audio input will be “learned” as Input 1.
*ODPNJOH
Press ENTER on the TV’s remote control.
$PBYJBM
$BCMF
While the text Input1 is flashing, press and hold the
TV INPUT key on the A/V receiver’s remote control.
When a check appears next to Input 1, release the
TV INPUT key.
• If the text stops flashing before the check mark
appears, repeat this step.
• To erase the IR code just “learned,” press CANCEL
while the name is highlighted.

5. Press
C
AV Receiver menu to set up audio switching

%JHJUBM4VSSPVOE4PVOE

Use this setup for:
• Sources providing only analog stereo output,
such as a VCR.
• Audio from ANT 1 and ANT 2

A/V Receiver Control: Automatic Audio
and Video Switching via HDMI
EJHJUBMTVSSPVOETPVOE

Audio Switching Setup 1: Automatic A/V Receiver
Switching to the TV Audio Input

once to highlight TV Audio (TV audio
output) in the Assign Input1 column. The triangular
marker is always next to the assigned sound source.
Press EXIT if finished or continue with setup for
another TV audio source.

%7%1MBZFS EJHJUBMTVSSPVOETPVOE
XJUI
%JHJUBM
4VSSPVOE
WJEFP
4PVOE

BVEJP WJEFP

If your A/V receiver has an HDMI output, you can use
this procedure to set up control of the A/V receiver’s
audio and video switching. The HDMI connection
allows you to route video signals from multiple devices
over a single cable to the TV. See the diagram on this
page. The connected devices can be analog, digital, or
a mixture or the two.

%7%BVEJP
JOQVU

Cable box
TV main
panel

"73FDFJWFS

Setup 2: A/V receiver audio from a device providing
surround sound directly to the A/V receiver

IR- NetCommand

INPUT3

Pr
VIDEO

L
AUDIO
R
Y

DVI/PC

Y / VIDEO

HDMI
cable

AUDIO

R
INPUT2

INPUT1

DIGITAL
AUDIO
OUTPUT

Completed NetCommand setup described for
controlling A/V receiver switching to an A/V receiver
input “learned” as Input2.

B A check mark next to a key name indicates it has
been “learned” by NetCommand.

(Video to TV)

DIGITAL
AUDIO
OUTPUT
ANT2/AUX

3. While the text Input2 is flashing, press and hold the

C Input1 through Input5 are arbitrary names the
TV uses to uniquely identify A/V receiver inputs.

4.
Completed NetCommand setup described for
controlling A/V receiver switching to the A/V receiver’s
audio input from the TV’s AUDIO OUTPUT.

DVD INPUT key on the A/V receiver’s remote control.
When a check appears next to Input2, release the
DVD INPUT key.
• If the text stops flashing before the check mark
appears, repeat this step.
• To erase the IR code just “learned,” press CANCEL
while the name is highlighted.

5. Press
IMPORTANT
All audio from what you are watching on the
TV is always available from both the TV’s AVR
AUDIO OUTPUT and DIGITAL AUDIO OUTPUT
jacks.
To use the digital surround sound capabilities
of your A/V receiver however, you must connect
your DVD player, satellite receiver, or cable box
directly to the A/V receiver, as surround sound
may not be available from the TV’s audio output.

HDMI OUT

S-VIDEO

Output / External
Controller Input

AVR AUDIO
OUTPUT

A The Learn column lists “learnable” input keys on
the A/V receiver’s remote control.

To summarize for the given example:
1. Connect the TV’s audio output to the A/V receiver’s
TV audio input.
2. Using this screen, “learn” the IR code for the A/V
receiver’s TV audio input as Input1 (item C above).
3. In the Assign Input1 column (item D above), assign
the name TV Audio (the default) to the A/V receiver
IR code previously learned as Input1.
4. Connect the DVD player’s audio output to the A/V
receiver’s DVD input.
5. Using this screen, “learn” the IR code for the A/V
receiver’s DVD audio input as Input2.
6. In the Assign Input2 column, assign the name DVD
to the A/V receiver IR code previously learned as
Input2 in this screen.

A/V receiver with
HDMI output

D After “learning” IR codes for A/V receiver inputs,
use the Assign Input column to identify the device
connected to the TV and the associated A/V
receiver input.

High-definition
DVD player

WJEFP

VCR

DVD player

HDMI

BOBMPHBVEJP

1. Connect your A/V devices to the TV and connect

Setting Up NetCommand Control of an A/V Receiver, continued

WJEFP

Before You Begin

6. NetCommand IR Control

(480i / 480p / 720p / 1080i)

6.
7.

once to automatically move the highlight to
the Assign Input2 column.
Use
to highlight DVD in the list of devices
recognized by the TV. The triangular marker always
shows the assigned sound source.
Press EXIT if finished or continue for additional TV
sources.

ANT1/MAIN

AVR AUDIO
OUTPUT

Optional
analog or
digital audio
connection

Audio from TV to A/V Receiver

Multiple video inputs on a single HDMI cable. You can
connect multiple video devices to an A/V receiver that
has an HDMI output. The optional audio connection
allows you to hear, through the A/V receiver, devices
connected to the TV only.
More About Using an HDMI Connection with this
Setup
•

Audio from devices connected directly to the TV
can be heard from the TV speakers only. This is
because audio signals are sent on the HDMI cable
in one direction only—from the A/V receiver to the
TV speakers.
To send audio to the A/V receiver from a device
connected directly to the TV, use one of the optional
audio connections shown in the diagram. For

6. NetCommand IR Control

Setting Up NetCommand Control of an A/V Receiver, continued

•

example, use an optional audio connection if you
wish to use the A/V receiver speakers to hear audio
from:
-- The ANT 1 or ANT 2 inputs
-- A device connected to the convenience input
(input 4), such as a game or camcorder.

6. When the Auto Input Sensing screen displays,

In some circumstances, audio from a device connected to the A/V receiver may not be passed over
the HDMI cable to the TV speakers. You must use
the A/V receiver speakers to hear audio in these
cases.

Setup to Control Switching to the TV’s Audio Output

Before You Begin
To complete these steps you will need:
• The remote controls for both the TV and the
A/V receiver.
• The IR emitter cable supplied with the TV.
• An HDMI-to-HDMI cable to connect the A/V
receiver to the TV and cables necessary to
connect devices to the A/V receiver.

1. Connect your audio/video devices to the A/V

2.
3.
4.
5.

receiver. Note the name of the device connected
to each A/V receiver input. This information will be
needed later to set up NetCommand’s automatic
input switching.
Connect the A/V receiver to the TV with an HDMIto-HDMI cable.
Connect the IR emitter cable to the TV and position
the IR emitter where it can send signals to the A/V
receiver. See “IR Emitter Placement,” page 55.
Power on the A/V receiver.
Set the TV’s remote control slide switch to the TV
position and power on the TV if needed.

Setting Up NetCommand Control of an A/V Receiver, continued

select device name AVR.

Setup to Control A/V Receiver Power and Volume

Perform the steps under “A/V Receiver Control: Power
and Volume,” page 60.
If you have used one of the optional audio connections to the TV’s AVR AUDIO OUTPUT or DIGITAL AUDIO
OUTPUT jacks, set up NetCommand to control switching
to the TV audio input. Perform the steps under “Audio
Switching Setup 1: Automatic A/V Receiver Switching
to the TV Audio Input,” page 62.

3. Press ENTER and the highlighted Input label will start

Use this setup to have NetCommand control a device
sending audio and video through the A/V receiver to the
TV via HDMI.

4. While the Input text is flashing, press and hold the

Note:

flashing to indicate readiness for “learning.”

Setup to Control Automatic Audio
and Video Switching via HDMI
Follow these steps if you wish NetCommand to control
switching of A/V receiver video as well as audio inputs.
When this setup is complete, you can use the TV’s
Input Selection menu to select a video device connected to the A/V receiver. You can also perform additional NetCommand setup to control devices connected
to the A/V receiver.

4
3

A/V Receiver

The labels Input1 through Input5 in the Learn
column are names used by the TV to uniquely
identify A/V receiver inputs.
With the highlight in the Learn column, highlight
one of the Input labels Input2 through Input5; it
is recommended you leave Input1 reserved for TV
Audio.

3 A check mark next to a key name indicates it has
been “learned” by NetCommand.
The Assign Input column provides a list
of possible device types. Use this list to
select the device type connected to the
associated A/V receiver input. The assigned
device name will appear in the Input Selection
menu.
4

Any Connection Type
HDMI
Cable

TV
2. Press EXIT to close any open menus and return to
3.
4.
6. On the TV’s remote control, press

1 The Learn column lists “learnable” keys from the
A/V receiver’s remote control.

If your A/V receiver and the connected device
have CEC capability, use this procedure to add
commands not available with CEC.
Set up NetCommand control of A/V receiver audio/
video switching via HDMI as described under “A/V
Receiver Control: Automatic Audio and Video
Switching via HDMI,” page 63.
Source
Device

Note:

2 Input1 through Input5 are arbitrary names used
by the TV to uniquely identify “learnable” A/V
receiver inputs.

key on the A/V receiver’s remote control for the
input you wish to associate with the selected Input
label.
When a check appears next to the Input label,
release the remote control key.
• If the text stops flashing before the check mark
appears, repeat this step.
• To erase the IR code just “learned,” press CANCEL
while the name is highlighted.

1. Display the Inputs > AVR menu.

The device type you select here will appear as an
icon in the TV’s Input Selection menu. You can
assign each device type in the list only once.
Press EXIT if finished or repeat these steps for additional video sources connected to the A/V receiver.

NetCommand IR Control: Device
Connected to an A/V Receiver

AVR menu for audio and video switching with
HDMI output

6. NetCommand IR Control

once. The
highlight will move automatically to the associated Assign Input column (Assign Input1 through
Assign Input5).
Use
to highlight the device type connected to
the A/V receiver input just “learned.” The Assign
Input column contains a list of possible device
types.
In the example above, a DVD player is connected to
the A/V receiver input the TV knows as Input2.

5.
6.
7.

normal TV viewing.
Press INPUT to open the Input Selection menu.
Highlight the icon for the A/V receiver input you
wish to control.
The A/V receiver’s remote control key for the input
must have been “learned” previously using “Setup
to Control Automatic Audio and Video Switching via
HDMI” on the opposite page.
Press ENTER to switch the TV to the A/V receiver and
the A/V receiver to the device.
Open the Inputs > Learn menu.
Perform NetCommand “learning” for the device by
following the steps in “Initial NetCommand Setup
for Most Devices,” page 56.

Appendices

Appendix A: Specifications

Appendix B: Bypassing the Parental
Lock
Inputs
Type

Dimensions (inches)

HDMI (digital
video/audio)

With Stand/Without Stand
Model

Qty.
4

Input Specifications

Height

Width

Depth

Weight (lbs.)

LT-40148

25.0/23.4

36.7

11.2/4.9

51.8/45.4

LT-46148

28.0/26.4

42.0

11.2/4.9

61.7/55.3

PC (digital signals only):

LT-46246

28.0/26.4

42.0

11.2/4.9

61.7/55.3

LT-52148

31.2/29.8

47.7

14.1/4.9

80.9/73

LT-52246

31.2/29.8

47.7

14.1/4.9

80.9/73

VGA (640 x 480, 60 Hz)
W-VGA (848 x 480, 60 Hz)
SVGA (800 x 600, 60 Hz)
W-SVGA (1064 x 600, 60 Hz)
XGA (1024 x 768, 60 Hz)
1280 x 720 (60 Hz)
SXGA (1280 x 1024, 60 Hz)
1920 x 1080 (60 Hz)
WXGA (1360 x 768, 60 Hz)

Picture Technology
Item

Specifications

LCD Screen

Color active matrix LCD, 1920 x 1080 dots,
16:9 aspect ratio

Channel
Frequency
Reception

Channel
Type*

Over-the-Air: VHF 2–13, UHF 14–69
Analog Cable: 1–125
Digital Cable: 1–135
Over the Air:

Analog NTSC, Digital ATSC with
sub-channels (all 18 video formats)

Cable:

Analog NTSC (non-scrambled)
Digital QAM 64 and 256 with subchannels (non-scrambled)

Composite
Video

S-Video

Component
Video (Y/Pr/Pb)

up
to 3

up
to 3
sets

Description
Audio Speakers

Qty.
2

Analog Audio
(Signal)

1
pair

Digital Audio
(Signal)

Output Specifications
5.5" x 2.2"
RCA Pin Plug, 500 mV rms + 200 mV
(full scale) for analog sources, 1.5
Vrms + 0.5 Vrms (full scale) for digital
sources.

1 dedicated set of component video
jacks; 2 sets share a jack with composite video
USB Photo Port

Antenna/Cable
input

Qty.
2

HDMI

1
5
pairs

For reading camera JPEG files and
GalleryPlayer files.
Analog left and right audio
RCA Pin Plug 500 mV (full scale), 43-k
ohm

The HDMI inputs are compliant with CEA-861D standards for standard, extended, and high-definition video; digital audio, and HDCP
copy protection.

If you forget your pass code, you can view the locked
TV without entering your pass code. When you are
prompted for your pass code, press the number 9 and
QV keys on the TV remote control at the same time. This
process temporarily unlocks the TV.
When entering the Lock menu, this process deletes
your old pass code and prompts you to enter a new
pass code.
•

You can either enter a new pass code to open the
Lock menu and make changes or press EXIT to close
the menu.

•

If any of the locks are turned on and you exit the
menus when prompted for a new code, the old
code and all lock settings are retained.

•

If all locks are turned off and you exit the menus
when prompted for a new code, then the previous
code is erased.

RCA Pin Plug, Signal Type Dolby
Digital, PCM stereo

Inputs
Type

CEA-770.1 & CEA 770.2 480i, 480p,
CEA 770.3 720p and 1080i (TV
analog component video standards)
RCA Pin Plug

1.0 Vp-p (includes sync),
75-ohm
Pr: 700 mV p-p, 75-ohm
Pb: 700 mV p-p, 75-ohm

Audio Inputs

Outputs

Four-Pin DIN Plug
Y: 1.0 Vp-p 75-ohm
C: 0.286 Vp-p (burst signal), 75-ohm

CableCARD™ Authorized scrambled and non(246 Series TVs) scrambled digital channels
* Note for Digital Channels: The channel numbers displayed on screen are
determined by the broadcaster or cable company and can vary from the standard
frequency number. If there is no channel-number information provided by the
broadcaster or cable company, the TV creates a channel number. The created
channel number uses the frequency number as the main channel number and the
program number as the sub-channel number.

NTSC 480i only
Video:
RCA Pin Plug, 1.0 V p-p,
75 ohm
1 dedicated composite video jack; 2
jacks shared with component video Y

Bypassing the Parental Lock
After you set the lock, you must use your pass code
to view a locked program, view the locked TV, view
a locked channel, cancel the lock, or enter the Lock
menus.

CEA-861D standard for digital audio
and video via HDMI
HDMI standard connector
Video:
60 Hz: 480i, 480p, 720p, 1080i
24 Hz, 30 Hz, 60 Hz: 1080p
Audio: PCM stereo

Lock Bypass Instructions Have Been Filed for
Future Reference

Size and Weight

Input Specifications
RF
F connector, 75-ohm

IMPORTANT
Cut along the dotted line and file bypass
instructions in a safe place for future reference.

IMPORTANT
When changing or deleting your pass code,
you must use the remote control included
with this TV. You cannot use a Mitsubishi
remote control from another component or a
“universal” remote.

Appendices

This page intentionally left blank

Appendix C: Programming the Remote Control
This appendix explains programming the TV’s remote
control to operate other A/V devices. This is distinct
from NetCommand control. The TV’s remote control
can operate other devices by three different methods:

VCRs and DVRs
CH
/
POWER
SLEEP
(FAST Forward)
(Pause)
(Play)

•

Remote Control Programming: You must move
the slide switch to the position specific to the
type of device.

•
•
•
•
•
•

•

NetCommand® IR “learning”: You can operate
other devices with the slide switch in the TV
position.

Mitsubishi VCRs are compatible with some additional
buttons.

•

NetCommand for HDMI devices: You may be
able to operate compatible CEC-enabled HDMI
devices with the slide switch in the TV position.
See the device’s Owner’s Guide and Appendix E.

•
•

Functions Available for Other A/V Devices
The TV’s remote control can be programmed to operate
other types and brands of A/V products. To use the
remote when programmed, set the slide switch to the
position labelled for the product type. The functions
performed in each switch position can vary depending
on the product. Not all functions work for all models.
The most common functions available are listed on this
page.

•
•
•
•
•
•

(Record)
(Reverse)
(Stop)
GUIDE (DVR only)
MENU (DVR only)
0–9 Number Buttons

Cable Boxes and Satellite Receivers

•
•
•
•
•
•
•
•

AUDIO (PAGE UP)
Cancel (on some
models)
CH
/
ENTER (on some models)
GUIDE (on some models)
LIST (246 Series TVs)
POWER
(on some
models)
VIDEO (PAGE DOWN)
QV (ENTER; for channels
on some models)

•
•

0–9 Number Buttons
(on some models)
F1–F4 (A, B, C, D keys
on some models)

The record/playback keys
(on some models):
•
(FAST Forward)
•
(Pause)
•
(Play)
•
(Record)
•
(Reverse)
•
(Stop)

A/V Receivers
•
•
•
•
•

MUTE
POWER
SLEEP
VOLUME
0–9 Number Buttons

•

Direct Input Selection
buttons: numbers,
FAV and QV (on some
Mitsubishi models)

CD Players
(not all functions for all models)

Set the remote control’s slide
switch to the type of device you
wish to program for or control.

•
•
•
•

SLEEP
(FAST Forward)
(Pause)
(Play)

•
•
•

(Reverse)
(Stop)
0–9 Number Buttons

DVD and Laser Disc Players
(not all functions for all models)
•
•

IMPORTANT
Some manufacturers may change their
products or they may use more than one
remote control system. The TV’s remote
control may be unable to operate your A/V
equipment in these cases.

•
•
•
•
•

CANCEL (on some
models)
CH
/
(for track
skip on some models)
ENTER
MENU
POWER
SLEEP
(on some
models)

•
•
•
•
•
•
•

(FAST Forward)
(Pause)
(Play)
(Record)
(Reverse)
(Stop)
0-9 Number Buttons
(on some models)

Appendices

Appendix C: Programming the Remote Control, continued
Programming the Remote Control

Switch Position

Affected Device

Cable/SAT

Cable Box
DTV Receiver
Satellite Receiver

VCR

VCR
DVR
Laser Disc Player
DVD Player/Recorder

DVD

DVD Player/Recorder
DVR
Laser Disc Player
VCR

Audio

A/V Receiver
Audio Amplifier
CD Player

2. Press and hold POWER on the remote control for
3.
4.

several seconds until the button blinks twice and
goes off.
Release the POWER button.
Enter the first five-digit code listed for your equipment.
• The POWER button blinks twice when you start to
enter the code and then once for each additional keypress.
• The POWER button blinks twice when you finish
entering a valid code.
• Move the slide switch to another position if you
need to start over or wish to exit programming
mode.
Point the remote control at the equipment and
press POWER. If the product has no power on/off
function, press a different key, such as
(Play),
(Stop), VOL , or MUTE.
• If the equipment responds, the remote control
is properly programmed to operate the equipment.
• If the equipment does not respond, repeat
steps 2–4 with the next five-digit code listed for
your equipment.

the space below for future reference.

Switch Position

Device Type

Code

VCR
DVD
AUDIO
Code Verification
To determine the code programmed for any position of
the slide switch:
1. Move the slide switch to the position you wish to
verify.
2. Press and hold POWER on the remote control for
several seconds until the button blinks twice and
goes off.
3. Press keys 9 9 0
4. Press 1 and count the blinks of the power button.
Write down the number of blinks as the first digit of
the code.
5. Repeat step 4 for the second, third, fourth, and fifth
digits of the code.

Audio Lock: Universal A/V Receiver Control
With Audio Lock active, the remote control operates
the volume and mute functions of the A/V receiver in all
positions of the slide switch. Activate Audio Lock if you
normally use an A/V receiver with your TV and other
A/V equipment.

1. Program the AUDIO position for your A/V receiver as
2.
3.

Programming Codes
Audio Amplifiers

CABLE/SAT

described earlier in this section.
With the slide switch in the AUDIO position, press
and hold POWER on the remote control for several
seconds until the button blinks twice and goes off.
Press keys 9 9 3 ENTER
The POWER button will blink twice to indicate Audio
Lock is active.

To Reset the Remote Control to Operate Volume
and Mute for the TV Speakers

1. Press and hold POWER for several seconds until the
2.

IMPORTANT
You may need to reprogram the remote
control after changing the batteries.

Appendix C: Programming the Remote Control, continued

6. Once you have found the correct code, write it in

1. Move the slide switch at the top of the remote to

the position for the product you want to control.
Refer to the table below. Only one of each device
type can be controlled in each slide-switch position.

Appendices

key blinks twice and goes off.
Press keys 9 9 3 VOL .
The POWER key will blink four times to indicate Audio
Lock has cleared.

Make

Acurus
Adcom
Altec Lansing
Aragon
Bel Canto
Design
Bose
Carver
Cary Audio
Design
Classe
Curtis Mathes
Durabrand
Flextronics
GE
Halcro
Harman/
Kardon
JVC
Klipsch
Krell
Left Coast
Lenoxx
Lexicon
Marantz
Mark Levinson
McIntosh
Modulaire
Mondial
Optimus
Parasound
Philips
Pioneer
Polk Audio
Primare
RadioShack
RCA
Realistic
Soundesign
Technics
Victor
Wards
Yamaha

Code

30765
31100, 30577
31742
30765
31583
30674
30892
31879
31461
30300
31561
31879
30078
31934
30892
30331
30765
31837
30892
31561
31802, 31145
30892
31483
30251
30395
30765
30823, 30395, 30300,
30013
31934
30892
30823, 30300, 30013
30892
31395
30395
30823, 30300, 30013
30013, 30395
30078
30372
30331
30078, 30013
30354

Cable Boxes
Make
Code
A-Mark
ABC

Accuphase
Acorn
Action
Active
Americast
Archer
BCC
Bell & Howell
Bell South
British
Telecom
Century
Clearmaster

10144, 10008
10237, 10014, 10011,
10008, 10007, 10003
10014, 10011, 10007,
10003
10237
10237
10237
10899
10237
10276
10014
10899
10003
10008
10883

Cable Boxes
Make
Code
ClearMax
Comtronics
Cool Box
Coolmax
Digeo
Digi
Director
Dumont
Emerson
Everquest
Fosgate
GC Electronics
GE
General
Instrument
Gibralter
GMI
GoldStar
Hamlin
Hitachi
Houston
Hytek
Hytex
Insight
Jebsee
Jerrold
Memorex
Mitsubishi
Motorola
Multitech
Nova Vision
Novaplex
NSC
Oak
Pace
Panasonic
Panther
Paragon
Penney
Philips
Pioneer
Prism
Pulsar
Pulser
Quasar
R-Line
RadioShack
RCA
Regal
Regency
Rembrandt
Runco
Samsung
Scientific
Atlanta

10883
10040
10883
10883
11187
10637
10476
10637
10014
10040
10276
10040

10144
10810, 10476, 10276,
10020, 10014, 10012,
10011, 10003
10003
10883
10144, 10040
10273, 10259, 10020
10011, 10008, 10003
10011
10007
10007
10476, 10810
10014
10810, 10476, 10276,
10020, 10014, 10012,
10011, 10003
10000
10003
11376, 11254, 11187,
11106, 10810, 10476,
10276, 10014
10883
10008
10008
10637, 10012
10007
11877, 10877, 10237,
10008
10144, 10107, 10008,
10000
10637
10525, 10008, 10000
10637, 10000
11305, 10317, 10259
11877, 10877, 10533,
10144
10012
10040, 10000
10040
10000
10040
10883
11256
10279, 10276, 10273,
10259, 10020
10020
10040, 10011
10000
10144, 10040, 10003
11877, 10877, 10477,
10237, 10012, 10008,
10003, 10000

Cable Boxes
Make
Code
Signal
Signature
SL Marx
Sony
Sprucer
Starcom
Stargate
Storm
Supercable
Supermax
Teleavia
Teleview
Thomson
Timeless
Tocom
Torx
Toshiba
Tristar
TV86
United Artists
United Cable
US Electronics
V2
Videoway
Viewmaster
Vision
Vortex View
Zenith

10040, 10011
10011
10040
11006
10144
10014, 10003
10040, 10014
10637
10276
10883
10040
10040
11256
10040
10012
10003
10000
10883
10040
10007
10276, 10014, 10011,
10003
10276, 10008, 10003
10883
10000
10883
10883
10883
10899, 10525, 10000

CD Players
Make
Code
Acoustic
Research
Aiwa
Akai
Arcam
Audio Pro
Audio
Research
Burmester
Cairn
California
Audio Labs
Cambridge
Soundworks
Carver
Cary Audio
Design
Classic
Curtis Mathes
Denon
DKK
DMX Electronics
Fisher
Garrard
Genexxa
GPX
Grundig
Hafler
Harman/
Kardon

30420

30157
30083
30157
30437
30157
30420
30157
30303, 30029
30157
30437, 30179, 30157
31876
31297
30032
30766, 30034, 30003
30000
30157
31325, 30179, 30000
30420
30032
31296
30157
30173
31202, 30173, 30157,
30100, 30083

CD Players
Make
Code
Hitachi
Inkel
Integra
Jerrold
JVC
Kenwood

KLH
Koss
Krell
LG
Linn
LXI
Magnavox
Marantz
Mark
Levinson
Matsui
McIntosh
MCS
Memorex
MGA
Micromega
Miro
Mission
Mitsubishi
Modulaire
MTC
Myryad
NAD
NSM
Onkyo
Optimus

Panasonic
Parasound
Penney
Philips
Pioneer
Polk Audio
Primare
Proceed
Proton
QED
Quad
Quasar
RadioShack
RCA
Realistic
Revox
Roksan
Rotel

30032
30180, 30157
30101
30003
31294, 30072, 30032
30626, 30190, 30037,
30029, 30028, 30000
31711, 31318
31317
30157
31208
30157
30179
30274, 30157, 30038
30626, 30435, 30180,
30157, 30038, 30029
31484
30157
31703, 30660, 30290,
30256
30029
30468, 30437, 30420,
30179, 30032, 30000
30083
30157
30000
30157
30098, 30083
30468, 30437, 30420,
30180, 30179, 30145,
30087, 30032, 30000
30420
30157
31208
30157
31327, 30101
31075, 30468, 30437,
30420, 30179, 30145,
30087, 30037, 30032,
30000
30752, 30388, 30303,
30029
30420
30029
30626, 30274, 30157
31087, 31062, 30468,
30032
30157
31852
30420
30157
30157
30157
30029
31075, 30468, 30437,
30420, 30180, 30179,
30032, 30000
30032, 30053, 30179,
30420, 30468, 31062
30468, 30437, 30420,
30180, 30179, 30145,
30087, 30032, 30000
30157
30435
30420, 30157

Appendices

Appendix C: Programming the Remote Control, continued

Appendix C: Programming the Remote Control, continued
Programming Codes, continued

Programming Codes, continued
CD Players
Make
Code
SAE
Sansui
Sanyo
Sears
Sharp
Sherwood
Sonic Frontiers
Sony

30157
30157, 30000
30179, 30087, 30000
30179
30180, 30037
31950, 30180
30157

31364, 30490, 30185,
30100, 30000
Soundesign 30145
Sugden
30157
Sylvania
30157
Symphonic
30180
TAG McLaren 30157
Tandy
30032
Tascam
30420
TDK
31208
Teac
30490, 30420, 30180
Technics
30029, 30303
Techwood
30303
Thule Audio 30157
Tivoli Audio
31553
Universum
30437
Victor
30072
Wards
30179, 30157, 30087,
30053, 30032
Yamaha
31292, 30490, 30036
Yorx
30000

Laser Disc Players
Make
Code
Carver
Denon
Harman/
Kardon
Magnavox

Marantz
Mitsubishi
NAD
Optimus
Panasonic
Philips
Pioneer
Polk Audio
Quasar
Sony
Technics
Theta Digital
Toshiba
Wards
Yamaha

20194, 20064
20241, 20172, 20059
20194
20241, 20217, 20194,
20064
20194, 20064
20243, 20241, 20059
20059
20059
20204
20194, 20064
20241, 20059
20194
20204
20201, 20193
20204
20194
20059
20059
20217

A/V Receivers
Make
Code
ADC
Adcom
Aiwa
Akai
Alco
AMC

30531
31617, 31616
31641, 31405, 31388,
31347, 31321, 31243,
30189, 30121
31255
31390
31077

Appendices

A/V Receivers
Make
Code
Amplifier
Technologies
Anam
Apex Digital
Arcam
Atlantic Technology
Audiophase
Audiotronic
Audiovox
B&K
Bel Canto
Design
BK
Bose
Brix
Cairn
Cambridge
Soundworks
Capetronic
Carver

31584

31609, 31074
31774, 31430, 31257
31189
31487
31387
31189
31627, 31390
30840, 30820, 30702,
30701
31584
30702
31933, 31253, 31229,
30639
31602
30189
31477

30531
31289, 31189, 30189,
30121
Classe
31920
Clatronic
30797
Coby
31263
Curtis
31263, 30797
Curtis Mathes 30014
Delphi
31414
Denon
31360, 31311, 31306,
31142, 30121
Electrohome 32026
Emerson
30531
Fisher
31801, 31409, 30797
Fosgate
31487
Glory Horse 31263
Goodmans
30797
GPX
31299
Grundig
31387, 30189
Harman/
31306, 31304, 31289,
Kardon
30891, 30189, 30110
Hitachi
31801, 31273
Insignia
31077, 31030
Integra
31805, 31320, 31298,
30842, 30135
JBL
31306, 30110
JVC
31811, 31643, 31495,
31374, 31282, 31263,
31058
Kawasaki
31390
Kenwood
31570, 31569, 31363,
31313
KLH
31428, 31390
Koss
31497, 31366
Linn
30189
Liquid Video 31497
Magnavox
31514, 31269, 31266,
31189, 30531, 30189
Marantz
31289, 31269, 31189,
30891, 30200, 30189
McIntosh
31289
Micromega
31189, 30189
Mitsubishi
31957, 31922, 31921,
31920, 31393
Myryad
31189

A/V Receivers
Make
Code
Nakamichi
Onkyo

31555, 31313, 30097
31805, 31320, 31298,
30842, 30135
Optimus
31074, 31023, 30849,
30797, 30670, 30531,
30121, 30014
Oritron
31497, 31366
Outlaw
31487
Panasonic
32967, 31764, 31763,
31633, 31548, 31518,
31509, 31363, 31350,
31316, 31308, 31288,
30309
Philips
31368, 31365, 31283,
31269, 31268, 31266,
31189, 30891, 30189
Pioneer
31384, 31343, 31123,
31023, 30630, 30531,
30150, 30014
Polk Audio
31414, 31289, 30189
Proceed
31922
RadioShack 31609, 31263
RCA
31609, 31511, 31390,
31123, 31074, 31023,
30531
Realistic
31609, 30121
Revox
30189
Rio
31869
Samsung
31500, 31304, 31295
Sangean
32165
Sansui
31189, 30189
Sanyo
31801
Sharp
31386, 31361
Sharper
31416, 31411, 31410,
Image
31409, 31385, 31263,
30797
Sherwood
31077
Sirius
31811, 31627, 31602
Sonic Blue
31869
Sony
31858, 31759, 31758,
31658, 31622, 31558,
31529, 31503, 31458,
31441, 31406, 31382,
31371, 31367, 31258,
31131, 31058
Soundesign 30670
Stereophonics 31023
Sunfire
31313
Sylvania
30797
Teac
31528, 31390, 31267,
31074
Technics
31633, 31518, 31308,
30309
Thorens
31189
Toshiba
31788, 31123, 30842,
30135
Venturer
31390, 30849
Wards
30189, 30014
XM
31414, 31406
Yamaha
31815, 31476, 31375,
31331, 31276, 31176,
31023, 30176
YBA
31921

Satellite Receivers
Make
Code
AlphaStar
Bell ExpressVu
Chaparral
Crossdigital
DirecTV

Dish Network
System
Dishpro
Echostar
Expressvu
Fortec Star
Funai
GE
GOI
Goodmans
Hitachi
Houston
HTS
Hughes
Network
Systems
Humax
Innova
JVC
LG
Magnavox
Memorex
Mitsubishi
Motorola
NEC
Netsat
Optimus
Panasonic
Pansat
Paysat
Philips

Pioneer
Proscan
RadioShack
RCA
Samsung
Sanyo
SKY
Sony
Star Trak
Thomson
Tivo
Toshiba
UltimateTV

10772
11170, 10775
10216
11109
11856, 11749, 11640,
11639, 11609, 11444,
11443, 11442, 11414,
11392, 11377, 11142,
11109, 11108, 11076,
10819, 10749, 10724,
10639, 10566, 10392,
10247, 10099
11775, 11505, 11170,
11005, 10775
11775, 11505, 11005,
10775
11775, 11505, 11170,
11005, 10775
11775, 10775
11821
11377
10566, 10392
11775, 10775
11246
11250, 10819, 10749
10775
11775, 10775
11749, 11444, 11443,
11442, 11142, 10749
11790, 11781
10099
11775, 11170, 10775
11414, 11226
10724, 10722
10724
10749
10856
11270
10099
10724
10701, 10247
11807
10724
11749, 11442, 11142,
11076, 10819, 10775,
10749, 10724, 10722,
10099
11442, 11142
10566, 10392
10775, 10566
11442, 11392, 11142,
10855, 10775, 10566,
10392, 10143
11609, 11442, 11377,
11276, 11142, 11109,
11108
11219
10856, 10099
11640, 11639, 10639
10772
10566, 10392
11444, 11443, 11442,
11142
11749, 10790, 10749
11640, 11392

Satellite Receivers
Make
Code
Uniden
Zenith

VCRs
Make
A-Mark

ABS
Accurian
Admiral
Adventura
Adyson
Aiko
Aiwa
Akai
Alba
Alienware
Allegro
America
Action
American High
Amstrad
Asha
Astra
Audiovox
Avis
Beaumark
Bell & Howell

10724, 10722
11856, 11810, 10856

Code

20278, 20240, 20046,
20037, 20000
21972
20000
20479, 20209, 20104,
20060, 20048, 20047,
20039
20240, 20037, 20000
20072
20278
20124, 20037, 20000
20242, 20175, 20041
20278, 20209, 20072
21972
20039
20278

20081, 20035
20000
20240
20240, 20035
20278, 20038, 20037
20072, 20000
20240
20479, 20104, 20048,
20046, 20039, 20035,
20000
Broksonic
20479, 20209, 20184,
20121, 20002
Calix
20037
Candle
20037, 20038
Canon
20035
Capehart
20002
Carrera
20240
Carver
20035, 20081
CCE
20072, 20278
Cineral
20278
Citizen
20479, 20278, 20240,
20209, 20037, 20035,
20000
Classic
20037
Colortyme
20278, 20060, 20045,
20035
Colt
20072, 20000
Craig
20240, 20072, 20047,
20037
Criterion
20072, 20000
Crosley
20081, 20035, 20000
Crown
20278, 20072
Curtis Mathes 20432, 20278, 20240,
20162, 20060, 20041,
20035, 20000
Cybernex
20240
CyberPower
21972
Daewoo
20278, 20046, 20045,
20037
Daytron
20278, 20037
Dell
21972
Denon
20081, 20042
Derwent
20041

VCRs
Make

DirecTV
Dual
Durabrand
Dynatech
Electrohome

Code

20739
20000
20039, 20038
20240, 20000
20240, 20209, 20060,
20043, 20037, 20000
Electrophonic 20037
Emerald
20184, 20121
Emerex
20032
Emerson
21593, 20593, 20479,
20278, 20240, 20209,
20184, 20121, 20043,
20037, 20002, 20000
Fisher
20104, 20047, 20046,
20039, 20000
Fuji
20035, 20033
Fujitsu
20000
Funai
21593, 20593, 20278,
20072, 20037, 20000
Garrard
20000
Gateway
21972
GE
20240, 20060, 20048,
20035, 20000
Gemini
20060
Genexxa
20278, 20037, 20000
Go Video
20614, 20526, 20432,
20240
GoldStar
20278, 20039, 20038,
20037, 20035, 20000
Goodmans
20278, 20081, 20072,
20037, 20000
Gradiente
20000
Granada
20081, 20042
Grundig
20081
Harley David- 20000
son
Harman/
20081, 20075, 20038
Kardon
Harvard
20072
Harwood
20072
Headquarter 20046
Hewlett
21972
Packard
HI-Q
20047, 20035, 20000
Hitachi
20089, 20045, 20042,
20041, 20037, 20035,
20000
Howard Com- 21972
puters
HP
21972
Hughes
20739, 20042
Network
Systems
Humax
21988, 21797, 20739
Hush
21972
Hytek
20072, 20047, 20000
iBUYPOWER 21972
ITT Nokia
20240, 20041
Janeil
20240
Jensen
20067, 20041
JVC
21162, 20067, 20041
KEC
20278, 20037
Kenwood
20067, 20046, 20041,
20038
KLH
20072
Kodak
20037, 20035

VCRs
Make
KTV
LG

Linksys
Lloyd’s
Loewe
Logik
Lumatron
Luxor
LXI
M Electronic
Magnasonic
Magnavox

Magnin
Marantz
Marta
Matsui
Matsushita
Media Center
PC
MEI
Memorex

Code

20000
21037, 20240, 20038,
20037
21972
20240, 20072, 20038,
20000
20081
20240, 20072, 20000
20278
20046
20067, 20042, 20037,
20000
20240
20593, 20278, 20240,
20072, 20037, 20000
21593, 20618, 20593,
20563, 20240, 20081,
20048, 20039, 20037,
20035, 20000
20240
20081, 20038, 20035
20037
20209, 20037
21162, 20162, 20081,
20035
21972

20035
21262, 21162, 21037,
20479, 20278, 20240,
20209, 20162, 20104,
20072, 20048, 20047,
20046, 20039, 20037,
20035, 20000
Metz
20037
MGA
20240, 20060, 20043
MGN Technol- 20240
ogy
Microsoft
21972
Midland
20240
Mind
21972
Minolta
20042
Mitsubishi
20443, 20242, 20214,
20173, 20075, 20067,
20060, 20048, 20047,
20043, 20042, 20041,
20000
Motorola
20048, 20035
Movie Walker 20072
MTC
20240, 20072, 20000
MTX
20000
Multitech
20072, 20039, 20000
NAD
20240, 20104
NEC
20104, 20067, 20041,
20038
New Tech
20072
Nikko
20278, 20037
Nikkodo
20278, 20037
Nishi
20240
Niveus Media 21972
Noblex
20240
Northgate
21972
Olympus
20162, 20104, 20035
Onkyo
20222

VCRs
Make

Optimus

Orion
Panama
Panasonic
Penney

Pentax
Philco
Philips

Pilot
Pioneer
Polk Audio
Portland
Presidian
Profitronic
Proscan
Protec
Protech
Pulsar
Pulser
Quarter
Quartz
Quasar
RadioShack

Radix
Randex
RCA
Realistic

ReplayTV
Ricavision
Runco
Salora
Samsung
Samtron
Sanky
Sansui

Code

21262, 21162, 21062,
21048, 20593, 20432,
20240, 20162, 20104,
20048, 20047, 20037,
20035, 20000
20479, 20278, 20240,
20209, 20184, 20121,
20104, 20002, 20000
20035
21262, 21162, 21062,
20616, 20614, 20225,
20162, 20035, 20000
20240, 20162, 20081,
20067, 20047, 20042,
20038, 20037, 20035,
20000
20042
20479, 20209, 20081,
20035, 20000
21181, 21081, 20739,
20618, 20616, 20209,
20162, 20081, 20048,
20045, 20035, 20000
20037
20162, 20081, 20067,
20042
20081
20278
21593
20240
20060
20072, 20000
20072
20278, 20240, 20039
20240
20046
20047, 20046, 20035
21162, 20162, 20035,
20002
21162, 21037, 20240,
20162, 20104, 20048,
20047, 20046, 20037,
20035, 20000
20037
20037
20880, 20240, 20060,
20048, 20045, 20042,
20035, 20000
21162, 20278, 20240,
20162, 20121, 20104,
20048, 20047, 20046,
20037, 20035, 20000
20616, 20614
21972
20039
20075
20739, 20432, 20240,
20060, 20045, 20038,
20000
20240
20048, 20039
20479, 20240, 20209,
20072, 20067, 20041,
20002, 20000

Appendices

Appendix C: Programming the Remote Control, continued

Programming Codes, continued
VCRs
Make
Sanyo

Code

20479, 20240, 20159,
20104, 20047, 20046,
20000
Scott
20184, 20121, 20045,
20043
Sears
20209, 20162, 20104,
20072, 20067, 20060,
20048, 20047, 20046,
20045, 20043, 20042,
20041, 20039, 20037,
20035, 20033, 20000
Sharp
20848, 20048, 20047,
20032, 20000
Shintom
20240, 20072, 20039,
20000
Shogun
20240
Siemens
20037, 20104
Signature
20479, 20060, 20048,
20046, 20037, 20035,
20000
Singer
20240, 20072, 20037
Sonic Blue
20616, 20614
Sonographe
20046
Sony
21972, 21032, 20636,
20067, 20047, 20046,
20035, 20033, 20032,
20000
Soundmaster 20000
Stack 9
21972
STS
20042
SV2000
20072, 20000
SVA
20000
Sylvania
21593, 20593, 20081,
20043, 20035, 20000
Symphonic
21593, 20593, 20240,
20002, 20000
Systemax
21972
Tagar Systems 21972
Tandy
20104, 20000
Tatung
20081, 20067, 20048,
20041, 20000
Teac
20067, 20041, 20000
Technics
20162, 20037, 20035,
20000
Teknika
20037, 20035, 20000
Telecorder
20240
Telefunken
20041
Tevion
20479
Thomas
20002, 20000
Thomson
20060, 20041
Tisonic
20278
Tivo
20739, 20636, 20618
TMK
20240, 20000
TNIX
20037
Tocom
20240
Toshiba
21988, 21972, 21008,
20240, 20209, 20045,
20043, 20041, 20000
Tosonic
20278
Totevision
20240, 20037
Touch
21972
Trix
20037
Ultra
20278, 20045
Unitech
20240
Vector
20045

VCRs
Make

Vector
Research
Vextra
Victor
Video Concepts
Videomagic
Videosonic
Viewsonic
Villain
Voodoo
Wards

Programming Codes, continued
Code

20184, 20038
20072
20067, 20041
20242, 20045

20037
20240, 20072, 20000
21972
20000
21972
20479, 20240, 20081,
20072, 20060, 20048,
20047, 20046, 20045,
20043, 20042, 20041,
20038, 20037, 20035,
20033, 20000
Wharfedale
20593
White
20479, 20278, 20209,
Westinghouse 20072, 20000
World
20479, 20209, 20002
XR-1000
20240, 20072, 20035,
20000
Yamaha
20041, 20038
Zenith
21139, 20479, 20278,
20209, 20041, 20039,
20037, 20033, 20000
ZT Group
21972

DVD Players
Make
Code
3D LAB
Acoustic Solutions
Accurian
Adcom
Afreey
Aiwa
Akai
Alba
Alco
Allegro
Amphion
Media Works
AMW
Apex Digital
Arrgo
Aspire Digital
Audiovox
Awa
Axion
B&K
BBK
Bel Canto
Design
Blaupunkt
Blue Parade
Blue Sky
Brandt
Broksonic

20539, 20503
20730
21416, 21072, 20675
21094
20698
20641
21089, 20770, 20705,
20695
20717, 20672
20790
20869
20872
20872
21061, 21056, 21020,
20794, 20755, 20717,
20672, 20533
21023
21407, 21168
21072, 21041, 20790,
20717
20730
21072
20662, 20655
21224
21571
20717
20571
20699, 20695
20651
20695

DVD Players
Make
Code
California
Audio Labs
Celestial
Centrex
Cinea
CineVision
Citizen

20490

21020
20672
20831
20876, 20869, 20833
22116, 21587, 21277,
21003, 20695
Clairtone
20571
Coby
21351, 21177, 21165,
21107, 21086, 21077,
20852, 20778
Craig
20831
Creative
20539, 20503
Curtis Mathes 21087
CyberHome
21537, 21502, 21129,
21117, 21024, 21023,
20874, 20816
Cytron
20705
Daewoo
21242, 21234, 21172,
21169, 20869, 20833,
20784, 20770, 20705
Dansai
20770
Daytek
20872
Decca
20770
Denon
20634, 20490
Denver
20778
Desay
21407
Digitrex
20672
Disney
21270, 20675
DiViDo
20705
Dual
21085, 21068, 20675
Durabrand
21127
DVD2000
20521
Electrohome 22116, 21003
Emerson
21268, 20675, 20591
Enterprise
20591
Entivo
20539, 20503
Enzer
20770
ESA
21268
Firstline
20651
Fisher
20670
Funai
21334, 21268, 20675
Gateway
21158, 21077, 21073
GE
20815, 20717, 20522
Go Video
21730, 21304, 21158,
21144, 21099, 21075,
21044, 20869, 20833,
20783, 20744, 20741,
20717, 20715, 20573
Go Vision
21072
GoldStar
20869, 20741
Goodmans
20790
GPX
20769, 20699
Gradiente
20651, 20490
Greenhill
20717
Grundig
20705, 20539
Harman/
20702, 20582
Kardon
Hello Kitty
20831
Hitachi
20664, 20573
Hiteker
20672
iLo
21348
Initial
20717
Insignia
22095, 21268
Integra
20627, 20571

DVD Players
Make
Code
IRT
Jaton
JBL
JMB
JSI
JVC

jWin
Kawasaki
Kenwood
KLH
Kloss
Konka
Koss
Lasonic
Lecson
Lenoxx
LG
LiteOn
Loewe
Logix
Magnasonic
Magnavox
Malata
Marantz
McIntosh
Medion
Memorex
Microsoft
Minato
Mintek
Mitsubishi
Momitsu
Mustek
Myryad
NAD
Naiko
Nakamichi
NEC
Nesa
NexxTech
Nintaus
Norcent
Onkyo
Oppo
Optimus
OptoMedia
Electronics
Oritron
Palsonic
Panasonic
Philco
Philips
Phonotrend
PianoDisc
Pioneer
Polaroid

20783
21078
20702
20695
21423
21164, 20867, 20623,
20558
21051, 21049
20790
20534, 20490
21149, 21020, 20790,
20717
20533
20721, 20711
21423, 21061, 20896,
20769, 20651
21173, 20798, 20627
21533
21127
20869, 20741, 20591
21440, 21416, 21158,
21058
20741, 20511
20783
20675, 20651
21506, 21268, 20675,
20646, 20539, 20503
21159, 20782
20675, 20539, 20503
21533, 21273
20651
21270, 20831, 20695
22083, 20522
20752
20839, 20717
21521, 20521
21082
20730
20894
20741
20770
21222
20869, 20785
20717
21402
21051
21265, 21107, 21003,
20872
21769, 20627, 20503
21525, 21224, 20575
20571
20896
20651
20852, 20672
21762, 21641, 20703,
20571, 20503, 20490
20675
22084, 22056, 21354,
21267, 20675, 20646,
20539, 20503
20699
21024
21571, 20631, 20571,
20525, 20142
21086, 21061, 21020

DVD Players
Make
Code
Polk Audio
Portland
Presidian
Proceed
Proscan
Prosonic
ProVision
Qwestar
Radionette
RadioShack
RCA
Realistic
Reoc
Revoy
Rio
RJTech
Rotel
Rowa
Saba
Sampo
Samsung
Sansui
Sanyo
Schneider
Schwaiger
Sensory
Science
Sharp

20539
20770
21072, 20675
20672
20522
20699
20778
20651
20741
20571
21769, 20822, 20790,
20717, 20571, 20522
20571
20752
20699
20869
21360
21178, 20623
20823
20651
20752, 20698
21075, 21044, 20820,
20744, 20573, 20490,
20199
20695
21334, 20873, 20695,
20675, 20670
20783
20752
21158

21256, 20752, 20675,
20630
Sharper Image 21117
Sherwood
21077, 21043, 20770,
20633
Shinsonic
20839, 20533
Slim Art
20784
SM Electronic 20730
Sonic Blue
21099, 20869, 20783,
20715, 20573
Sony
21536, 21533, 21516,
21431, 21070, 21033,
20864, 20533
Sungale
21074
SVA
21105, 20860, 20717
Sylvania
21268, 20675
Symphonic
21334, 21268, 20675
TAG McLaren 20894
Tatung
20770
Teac
20790, 20717, 20571
Technics
20703, 20490
Technika
20770
Technosonic 20730
Tevion
20651
Theta Digital 20571
Thomson
20522, 20511
Tivo
21503
Toshiba
21769, 21608,, 21515,
21503, 21154, 20695,
20573, 20539, 20503
Tredex
20804, 20803, 20800
Unimax
20770
United
20730
Universum
20591

DVD Players
Make
Code
Urban Concepts
US Logic
V
Venturer
Vizio
Vocopro
Wesder
Xbox
Yamaha
Yamakawa
Zenith
Zeus
Zoece

20539, 20503
20839
21226, 21064
20790
21226, 21064
21360
20699
22083, 20522
20545, 20539, 20497,
20490
20872
20869, 20741, 20591,
20503
20784
21265

Appendices

Appendix D: TV Guide Daily (246 Series TVs)

Active Selection
Source and Channel
Information
Info Box
Clock

Appendix D: TV Guide Daily (246 Series TVs), continued

Program
Rating Icons
Info Bar

Progress
Indicator

Setting Up TV Guide Daily

Navigating the Guide

Setup of the TV Guide Daily system is optional.
1. Display the Inputs > Guide menu to display TV
Guide Daily setup options.
2. To enable the TV Guide Daily system, highlight On.
If you wish to disable the system, highlight Off.

To navigate within the Guide, move the highlight through
the screen using the TV remote control’s
and
CH/Page keys. The highlight indicates the currently active
tile in the Guide. Press INFO to see help and program
information.

Info Icon

Video Window
Program
Title Tile
Highlighted Tile
(indicates active
selection)

Ad Panel

Channel
Call Letters

Channel
Number

HD
(high-definition)
Icon

Inputs > Guide menu for TV Guide Daily setup
3. Select program sources on TV antenna inputs for
the listings. You can select one over-the-air source
or one direct-cable source for TV Guide Daily. If,
however, you have multiple cable sources, the
channel-number assignments may not match up
correctly. See the following table and notes for the
preferred connection combinations.
•

This appendix explains the free TV Guide Daily service
available with this TV. Use this optional service to:
• View 24 hours of show listings.
• Change how channels are displayed (channel
call letters, numbers, or both).
• Watch the currently tuned channel while browsing listings.
• Get quick program information; icons indicate
show ratings, new episodes, stereo, HD broadcasts, and closed captioning availability.
• Quickly tune the TV to a selected channel.
• View show descriptions and “what’s on next”
information for a selected channel in an
expandable INFO box.
• Customize the channel lineup and listings

Initial Guide Setup
Before you can use TV Guide Daily, you must perform
the initial setup from the TV’s Inputs menu. See
“Setting Up TV Guide Daily,” page 77. Note: These
settings can be changed at a later date using the same
procedure.

Main Guide Screen Elements
•

•

•
•

The TV Guide Daily screen provides basic
program information, channel call letters and
number, current time, program rating, and high
definition programming (HD) icons.
The Highlight indicates the current active
selection. To navigate the screen, move
the highlight using the TV remote control’s
keys.
The Info Bar displays specific broadcast
information (new episode, TV or movie rating)
and a show progress indicator. The Info Icon
indicates that information or help is available.
The Info Box displays selected program
information, upcoming channel programming,
and help information.
The Video Window displays current channel
programming while in the Guide.
The Ad Panel displays program or product
information.

•

IMPORTANT
Leave the TV powered off for a while each day to
allow new listings to download.
Energy Mode. When you activate TV Guide
Daily, the TV automatically overrides a Low
Power setting and changes to the Fast Power
On setting.

If One Source Is:
Ant-1 Channels via Cable

The Other Source Can Be:
Ant-1 Air

Ant-2 Air

N/A

Ant-2 Channels via Cable

N/A

Note:
• Inputs to TV Guide Daily can include only one overthe-air source or only one direct-cable source.
• TV Guide Daily listings can be downloaded from an
over-the-air antenna or direct cable connected to
ANT 1 or ANT 2.
4. Highlight the ZIP Code digits and enter the fivedigit ZIP code for your location. To receive the
correct program listings for your area, you must
enter the ZIP code.

Using the TV Guide Daily System
With the Guide set up and enabled, press the GUIDE key
on the remote control to launch the TV Guide Daily system.

To open and close the Guide
• Press GUIDE to open or close TV Guide Daily (EXIT can
also be used to close the Guide).
Note: Until the initial 24 hours of program listings
have downloaded, the Setup Progress screen
appears when you first open the Guide. Once the
initial listings download is complete, the screen will
go directly to the Guide.
To navigate through screens
to move the highlight one item at a
• Press
time.
• Press CH/PAGE
/
(Channel/Page Up/Down) to
move up or down one full screen at a time.
• Press INFO to open the Info Box for on-screen help
and program information. When the Info Icon is
displayed on the Info Bar, press INFO repeatedly to
view either full or brief information.
Program Information. With a program title
highlighted, press the INFO key to see information in
the Info Box for currently available and upcoming
programs.
• While in the Guide, press MENU to display the Guide
Setup screen. See also “Modify Guide Setup” on
the next page.
To jump to a specific channel in the Listings
Enter a channel number using the remote control’s
number keys. Use the –/cancel key to enter the separator
for a digital sub-channel number. Press ENTER to move
the highlight to the channel just entered.
Note: If the channel number entered does not exist,
the highlight will move to the closest channel that is
present in the listing.
To tune the TV to a program in the listings
Highlight the desired program title in the listings, then
press ENTER.
Note: If the highlighted program airs sometime in the
future, the TV will tune to the channel on which that
show will air.
To check Guide setup progress
The Setup Progress screen displays the current Guide
setup status. To open the Setup Progress screen:
1. While in the Guide Listings, press MENU. This displays the Setup Screen.

Appendices

Appendix D: TV Guide Daily (246 Series TVs), continued
2. In the Setup Screen, press

to highlight “Display
setup progress” and press ENTER. The Setup Progress screen appears.

3. Press GUIDE to exit the Guide or press ENTER to return
to the Setup Screen.

Looking at Ads
To view promotions linked to ads
• Repeatedly press to move the highlight to the Ad
panel. A screen with additional Ad information will
appear.
• To close the Ad screen, press to move the highlight back to the listings.
Note: Some ads promote currently airing programs.
If the ad is linked to a currently airing show,
highlight the ad and press ENTER to watch the show.

Customizing Guide Listings
You can customize how the Listings screen displays
channel call letters/numbers. The options are:
• Both. Both the channel call letters and number are
displayed.
• Call Letters. Only call letters are displayed.
• Number. Only channel numbers are displayed.
To change the Channel ID display
1. Press to move the highlight to the desired channel
tile (channel number/call letters).

2. Press ENTER to change the display (Both, Call Letters,
3.

or Number). Each press of the ENTER key cycles
through the choices.
To save changes, press to move the highlight
back to the program listings.

Modifying the Guide Setup

From the Guide Setup screen, you can change the
channel lineup, change channel display settings, and
view setup progress (e.g., when the next listings update
will occur).
To select a channel lineup
You can view or change the channel lineup if more than
one is available. Use the following procedure:
1. While in the Guide Listings, press MENU. This displays the Setup Screen.
2. Press to highlight “Change channel lineup” and
press ENTER. A selection screen will appear.
3. Make your lineup selection:
• If only one selection is available, Next will be
highlighted. Press ENTER.
• If more than one selection is available, but you
want to use the one already selected (check
marked), press ENTER.
• If more than one selection is available and you
want to select a different lineup, press to
move the highlight back to selections. Press
to move the highlight to the desired lineup
and press ENTER to select it (add a check mark).
Press to highlight Next and press ENTER.
A confirmation screen will appear.
4. In the confirmation screen, verify the lineup selection:
• If the selection is correct, press ENTER to select
Yes (add check mark), press to highlight
Next, and then press ENTER.
• If the selection is incorrect, press to highlight
No, press ENTER to select (add check mark),
press
to highlight Next, and then press ENTER
to return to the Make Lineup Selection screen.
Note: You may need to try several lineup options
before you receive the correct one for your area. To
edit a specific tune channel number in the Listings grid,
see “To Modify Channel Settings” below.
To modify channel settings
You can edit how channels appear in the Guide Listing.
Note: The default settings for each channel are determined by the broadcast data received by your TV.
Available Options
• Position. Order of the channel in the Listings.
• Channel. Determines whether or not the channel
is displayed in the Listings (On, Auto-hide, and Off).
Auto-hide displays channels only when show information is available.
• Tune Channel. Shows the channel number that
displays in the Listings and which channel number
is used when tuning to that channel.

Appendix D: TV Guide Daily (246 Series TVs), continued
Procedure
1. While in the Guide Listings, press MENU. This displays the Setup Screen.
2. Highlight “Change channel display” and press
ENTER. The channel editor screen will appear.
3. Use
to highlight the desired row setting to be
changed.

•

To change channel position (Position Number
highlighted), press to move the position or
enter a new channel position number. When
correct, press
to move the highlight to
another position on the grid to save changes.
To change channel display status (status tile
highlighted; next to position number), repeatedly press ENTER to cycle through choices (on,

•

auto, off). When correct, press
to move
the highlight to another position on the grid to
save changes.
To change tune channel number* (Channel
Tune Number highlighted; far right), enter
desired number with remote control number
keys (—/CANCEL key for digital sub-channel
separator). When correct, press
to move
highlight to another position on the grid to save
changes.

*Note: If you receive both analog and digital versions
of the same channel, do not change the tune channel
number of the digital channel to match the analog
station, as this may hinder the ability of the Guide to
receive data. Instead, locate the digital station in the
channel editor and, if necessary, change the channel
row position to a location you prefer.

TV Guide Daily Troubleshooting Tips
Symptom

Remarks

When I enter the Guide I see a Setup Progress You have not yet received all of the program listings (it may take up
screen.
to 24 hours to receive a full grid of listings).

Listings reads “Listings Pending.”

The Guide has not yet completed initial setup, changes you made
have not completed, or the Guide is setup incorrectly. Verify that
your TV is properly connected to the input source. Then, verify that
the ZIP code and input source (entered during initial setup of Guide)
are correct. See “Setting Up TV Guide Daily,” page 77 for more
information.

Tiles in Listings read “No Listing” or “Title
Unavailable.”

The Guide has not received updated show information or no information was available the last time the Guide received an update,
update did not occur, or there was a power failure. Make sure you
turn the TV off when not in use to allow for updates. In the case of a
power failure, it may take up to 24 hours to update listings.

Tiles in Listings read “Turned Off.”

The channel you were watching before entering the Guide is turned
OFF in the grid. Use the channel editor to change the channel
setting to ON (see previous page, “Modify Guide Setup”).

There are repeated or missing time slots in the The Guide is close to the time that a Daylight Savings time adjustListings.
ment is needed. The Guide automatically adjusts accordingly when
the local time is 2:00 a.m. to account for the affected hour of programming. Once the adjustment is made, the Listings should return
to normal within 24 hours.

My channel lineup is incorrect or I see a
channel lineup screen when I enter the Guide.

An incorrect lineup for your area is selected in the Guide setup.
Select the correct channel lineup for your area (see previous page,
“Modify Guide Setup”).

My TV is tuned to a different channel than the
one I was watching the last time the TV was
turned off.

The Guide changes the channel to receive updates and does not
change the channel back until the update is complete. If the TV
is turned on before the update is complete, the channel will not
change back automatically.

Appendices

Appendix E: NetCommand HDMI Control of CEC Devices
Many new HDMI devices have a feature called CEC
(Consumer Electronics Control) or HDMI Control.
Mitsubishi calls this feature NetCommand HDMI Control
or NetCommand for HDMI. HDMI CEC allows one device,
such as the TV, to control other devices, such as an A/V
receiver or disc player. CEC use is optional.
Each manufacturer chooses which CEC functions to support
so it is difficult to predict which devices and features are
compatible with Mitsubishi’s NetCommand for HDMI. You
may find that CEC functions for a specific device are limited.
To use CEC, you must enable operation in all three
of the following:
• The TV’s Inputs > NetCommand HDMI Control
menu. When off, the TV sends no control signals to CEC
devices. NetCommand HDMI control is off by default.
• The TV’s Inputs > Name menu. You can turn
on or off the TV’s control signals to individual
CEC devices. This option operates only when
NetCommand HDMI Control is enabled.
• The device setup menus. Most devices with HDMI
CEC compatibility let you turn it on or off in the device
menus, where it is typically listed as “HDMI Control.”

Enabling or Disabling the TV’s NetCommand
HDMI Control
1. Press MENU to display the TV Main menu.
2. Highlight Inputs using
.
3. Press and then to select NetCommand HDMI
4.

•

1.
2.

First turn on the device and allow the power-on
sequence (boot up) to complete. Stop any playback,
and then connect the HDMI cable as described next.
Turn on the device and allow it to complete the
power-on sequence (boot up).
Connect the device to one of the TV’s HDMI inputs.
When the TV detects the connection, the Auto Input
Sensing screen will appear and provide additional
instructions. You will see one of the following
screens, depending on your equipment.
• Figure 2 (TV recognizes the CEC device). The
TV’s NetCommand HDMI Control is on and the
device’s CEC capability is on. This screen confirms the device is CEC compatible by showing
the name provided by CEC. The screen shown in
figure 3 may display first before figure 2 appears.

Connecting HDMI Devices to the TV
When setting up CEC control:
• Switch on the TV’s NetCommand HDMI control as
described above. NetCommand for HDMI is off by
default.
• Connect and set up HDMI devices one at a time.

Appendix E: NetCommand HDMI Control of CEC Devices, continued
not be compatible with CEC. Control the
device with its own remote control or use the
TV’s NetCommand IR control.
•

Note:

6. If the A/V receiver is HDMI CEC compatible, turn on

HDMI control in the A/V receiver (see the A/V receiver
menus). If the A/V receiver menu does not show
HDMI control, the A/V receiver may not be compatible with CEC.

Figure 4 (NetCommand HDMI Control is off).
The TV’s NetCommand for HDMI Control is
turned off.
Action: Follow the instructions in “Enabling or
Disabling the TV’s NetCommand HDMI Control”
on the opposite page.
You may not see the screen in figure 2 if the
HDMI device has previously been detected by
the TV. To check if CEC is enabled for the device, see the Inputs > Name menu. If you are
unable to change the device name, it indicates
CEC is enabled.

Cable box

DVD player

HDMI

HDMI
Cable

A/V receiver with
HDMI output

1
IR- NetCommand

HDMI OUT

DIGITAL
AUDIO
INPUT

S-VIDEO

Output / External
Controller Input

INPUT3

Pr
VIDEO

L
AUDIO
R
Y

DVI/PC

HDMI
cable
(Video
to TV)

Y / VIDEO

AUDIO

R
INPUT2

INPUT1

DIGITAL
AUDIO
OUTPUT

AVR AUDIO
OUTPUT

DIGITAL
AUDIO
OUTPUT
ANT2/AUX

Figure 2. TV recognizes the CEC device. The TV’s
NetCommand for HDMI is on and the connected device’s
HDMI Control is also on.

Control and open the menu shown in figure 1.
Use
to turn NetCommand HDMI Control On or
Off; Off shuts off all NetCommand for HDMI signals.

Figure 1. The TV menu Inputs > NetCommand HDMI
Control lets you set HDMI control either on or off.

Appendices

(480i / 480p / 720p / 1080i)

Figure 4. NetCommand HDMI Control is off.

3. With the HDMI CEC device powered on, switch the

Figure 3. “Power on the device.” The TV’s NetCommand
HDMI Control is on but either the connected device’s
HDMI Control is off or the device is not CEC compatible
• Figure 3 (“power on the device”). One of these
conditions applies:
-- The TV’s NetCommand HDMI Control is
turned on, but HDMI control is turned off in
the menu of the new device.
Action: Enable the device’s CEC capabilities in the device’s setup menus. Within a few
minutes you may see the screen in figure 2.
-- The device has not yet been detected (e.g.,
no power).
Action: Power on the device.
-- The device does not have CEC compatibility.
Action: Check the device’s setup menus. If
there is no HDMI control listed, the device may

TV to the device (press the INPUT key, highlight the
device icon, press ENTER). Within a few minutes CEC
will be established. You may see the screen shown
in figure 2. If the screen does not display, ensure
HDMI control is turned on in the device’s menus.
Once CEC has been established, CEC will automatically name the device. Any name you may
have previously selected in figure 3 or figure 4 will
be changed to the new name.

NetCommand HDMI Control for an HDMI
A/V Receiver and Connected Devices

TV main panel

2.
3.

4.
5.

Audio from TV to
A/V Receiver

Connecting HDMI devices. The optional digital audio
connection allows you to hear audio through the A/V
receiver from devices connected to the TV only.

7. Plug in the AC power cord and power on the first

8.
9.

1. Turn on the TV’s NetCommand for HDMI feature.

See “Enabling or Disabling the TV’s NetCommand
HDMI Control” on the opposite page.
Connect the A/V receiver to the TV before connecting any other device to the A/V receiver.
If you want to be able to switch between the A/V
receiver speakers and the TV speakers, also
connect the TV’s DIGITAL AUDIO OUTPUT to an
input on the A/V receiver.
Power on the TV and A/V receiver and allow both to
complete the power-on sequence (boot up).
Connect the HDMI output of the A/V receiver to the
TV’s HDMI input. The TV will automatically switch
to the input.

ANT1/MAIN

Optional digital
audio connection

HDMI device, such as a disc player, cable box or satellite receiver, and allow the device to complete the
power-on sequence (boot up). Stop playback if the
device starts playing.
Connect the device to the A/V receiver with an HDMI cable.
Select the device’s HDMI input on the A/V receiver’s
front panel controls or remote control.
• If the new device has the HDMI CEC Control
feature turned on, the TV will show a display
similar to Figure 2 and automatically name the
device.
• If the new device has the HDMI CEC Control
feature turned off or if it is not CEC compatible,
there will be no display.
Check the new device’s menu for the HDMI
Control feature and turn it on. If there is no HDMI
Control feature listed, this device may not be
compatible with HDMI CEC and you will need to
control the device manually.

10. After the present device has been connected and set
11.

up, repeat steps 7 through 9 for the next HDMI device.
If desired, perform NetCommand IR Learning to
supplement CEC functions.

Appendices

Appendix E: NetCommand HDMI Control of CEC Devices, continued

Appendix F: Troubleshooting

Resolving CEC Conflicts, Changing HDMI
Connections, Removing HDMI Devices
Because each manufacturer selects which CEC functions to support, some devices can conflict with other
devices. If control conflicts arise, you can:
• Turn off CEC in the other device’s setup menu.
• Turn off TV control of an individual CEC device (see
below).
• Reset TV control of an individual CEC device (see
below).
Turning Off the TV’s HDMI Control of an Individual
CEC Device (Figure 5)

1. Press MENU on the TV remote control to enter the TV
2.
3.
4.
5.
6.

Main menu.
keys.
Select the Inputs menu using the
Select the Inputs > Name menu using the key.
Highlight the device using the key and then the
key.
With the device highlighted, select Control Off to
turn off the TV’s ability to control the device.
Press EXIT to clear the menus.

TV Reset Comparison Guide
You can resolve many common TV problems using
the reset functions described in the following table.
See also the troubleshooting suggestions later in this
appendix.
IMPORTANT
Before you change sound or picture settings: If
picture or sound settings seem wrong for a broadcast
Figure 6. Inputs > Name menu with AVR DVD deleted.

As an example of using NetCommand for HDMI
devices, you would press PLAY on the device itself to:
• Turn on the TV if not already on
• Switch to the device (no need to display the Input
Selection menu)
• Begin play of the device
Test your equipment with the TV’s remote control to
find out which commands are supported. See the table
below for commands that may be available, depending
on the individual device.

When to Use

Format

Press the FORMAT key to cycle through
When the picture
shape seems incorrect, the available formats to find the best
format for the current picture.
use FORMAT to change
the shape of the
picture.

The last-used format for a signal
type is memorized for each input.
The next time the same input and
the same signal type is viewed,
the last-used format will be
recalled.

PerfectColor™
and PerfecTint™
Reset
(for the single
input currently
being watched))

When the color
intensities seem out
of balance, use the
PerfectColor/PerfecTint
reset to reset the color
balances to the original
factory settings.
Both PerfectColor and
PerfecTint and are reset
at the same time.

1. While viewing the input to be
reset, press MENU to display the
Main menu with the A/V icon
highlighted.
2. Use to highlight PerfectColor
and press ENTER to display the
PerfectColor adjustment screen.
3. Press CANCEL to reset the colors.

All PerfectColor/PerfecTint sliders
are reset to the original center
position. The PefectColor/PerfecTint
settings for other inputs remain
unchanged.

A/V Memory
Reset
(for the single
input currently
being watched)

When audio and/
or video settings for
a single input seem
incorrect, use A/V
Memory Reset to
return the input to
the original factory
settings.

1. While viewing the input to be
reset, press MENU to display the
Main menu with the A/V icon
highlighted.
2. Use to highlight the Reset
icon and press ENTER to reset.

All Audio and Video settings
for the individual input are
reset except for the Listen To,
Language, audio Balance, and
Closed Caption settings.

A/V Reset
(for all inputs)

To reset audio and
While viewing the TV, press the
video adjustments for
control-panel buttons GUIDE and
all inputs to the original FORMAT at the same time.
factory settings.

Channel
Memorization

To erase and
re-memorize channels
on Ant 1 or Ant 2.

CEC-enabled VCR, DVD, and DVR functions that
may be available:
Menu
Navigation

Channel Tuning
CH

Enter

Figure 5. Inputs > Name menu with HDMI Control for
AVR Tuner turned off
Resetting HDMI Control or Removing an HDMI
Device (Figure 6)

1. Power off the device.
2. Disconnect the HDMI cable.
3. Press MENU on the TV remote control to enter the TV
4.
5.
6.
7.
8.

Main menu.
Select the Inputs menu using the
keys.
Select the Inputs > Name menu using the key.
Highlight the device to reset using the key and
then the key.
With the device highlighted, select Delete to reset
HDMI Control.
Press EXIT to clear the menus.
Reconnect the device to display the Auto Input
Sensing screen.

—
CANCEL
(to cancel)

—
Digits 0–9, CANCEL
ENTER

Other
Guide

F1 (content)
MENU

The F1 key defaults to work like the device’s LIST key.

If you have a CEC-enabled A/V receiver, CEC-enabled
devices connected to the A/V receiver with an HDMI
cable may also be controllable. They can be selected
from the TV’s Input Selection menu.

CEC-enabled A/V receiver functions that may be
available:
• Try the VOL, MUTE, and menu-navigation keys.
• To open the A/V receiver menu, follow these steps:
1. While watching TV, press AUDIO.
2. Press repeatedly until the Speakers option
displays.
3. While Speakers is still displayed, press MENU.
You can use NetCommand IR “learning” to add commands to those supported by CEC. You must first
connect and place IR emitters for the devices.

channel (a channel from ANT 1, ANT 2, a cable box, or
satellite receiver), first check other channels from the
same input before changing settings. If most other
channels from the same input seem correct, there is
likely a problem with the broadcast rather than with the
TV. Use care in this case, as changes you make to fix
problems on individual channels also affect all other
channels on the same input.

Reset Name

Using NetCommand HDMI Control

Record/
Playback

How to Use

1. While viewing the TV, press MENU
to display the Main menu.
2. Press to highlight the Setup
icon.
3. Press to highlight the Scan
icon.
4. Press to highlight the antenna
input and reception mode, e.g.
Ant 1 Air.
5. Press to highlight the Start
button icon and press ENTER to
start the memorization.

Resulting Action

All Audio and Video settings are
returned to the original factory
settings, including Listen To and
Language, plus Closed Captions
settings and Format settings.
All previously memorized channels for the selected antenna
input are erased and a new
set of memorized channels is
created. All custom settings for
Fav, channel names, and channel
locks are deleted. To add or
delete individual channels, see
Edit menu instructions on page
45.
246 Series TV. CableCARD
channels are reacquired.

Appendices

Appendix F: Troubleshooting, continued

Reset Name

When to Use

How to Use

Resulting Action

Lock Menu
Pass Code

To change your Lock
menu pass code

See the cutout page in Appendix B,
page 67.

Allows a new code to be
established.

Control-Panel
Lock Release

To re-enable the
control-panel buttons
after activation of the
Control-Panel Lock

Press and hold the MENU button
on the control panel for over eight
seconds. This works even if the TV
is powered off.

Allows the control panel to be
unlocked if the remote control is
misplaced.

System Reset

If the TV does not turn
on or off, does not
respond to the remote
control or controlpanel buttons, or has
audio but no video.

Press the SYSTEM RESET button on the
control panel.

The TV will turn off and the green
LED will flash quickly for about
one minute. When the green LED
stops flashing, you may turn on the
TV. The changes you made most
recently, before using SYSTEM RESET,
may be lost. Changes you made
previously, however, are not lost.

To reset all consumeraccessible settings
and all memories to
the original factory
defaults.

1. While viewing the TV, press MENU
to display the TV Main menu.
2. With the Main menu displayed,
press number keys 1 2 3 to
display the Reset menu.
3. READ THE ON-SCREEN
WARNING AND INSTRUCTIONS.
• If you do not wish to use this
reset, press EXIT or MENU to
back out.
• If you do wish to use the
reset, press ENTER to erase all
memories and settings.

TV Reset
IMPORTANT:
Use this reset
only if all other
resets have
been unsuccessful.

CAUTION: All ownerperformed setups and
adjustments will be
erased.

The TV will start the initialization
process. The TV will then turn off
and the front green LED will start
flashing. When the LED stops
flashing, you can turn the TV on
again. The Parental Lock Pass
code will remain unaffected, but
all other memories and settings
outlined in this Owner’s Guide
will need to be set again.

General TV Operation
1.

Symptom

Remarks

The TV remote control does not work.

•
•
•
•
•
•

Service and Customer Support

Customer Support

Service

•

DO NOT adjust any controls other than those
described in this Owner’s Guide.

•

DO NOT remove the protective back cover of
your TV.

•

To order replacement or additional remote controls or Owner’s Guides, visit our website at www.
mitsuparts.com or call (800) 553-7278.
For questions:
Call Consumer Relations at 800-332-2119.
E-mail: MDEAservice@mdea.com
Website: www.mitsubishi-tv.com

Check that the batteries are fresh and installed correctly.
Check that the slide switch on the remote is set to TV.
Be no more than 20 feet from the TV when using the remote
control.
Program the remote control to operate the TV or other device.
Reset the remote control.
If you have a custom home theater controller but prefer to use
the TV’s remote control, unplug the controller cable from the
TV’s IR—NetCommand® Output/External Controller Input.

When I try to use the remote control, the
POWER key blinks five times.

Replace the batteries.

TV does not respond to the remote control or to
control-panel buttons and TV will not power on
or off.

•
•
•

Unplug the AC power cord for 10 seconds.
Use the System Reset button.
If you have a custom home theater controller but prefer to use
the TV’s remote control, unplug the controller cable from the
TV’s IR—NetCommand® Output/External Controller Input.

When a device is selected from the Input Selection menu, the screen is blue or black (no signal
source).

•
•

Make sure the selected device is turned on.
Begin play of the device.

You have forgotten your Lock menu pass code.

See Appendix B, “Bypassing the Parental Lock,” page 67.

Rating restrictions are not working.

Open the Parental Lock menu and:
• Verify that the U.S. Ratings or Other Ratings setting is On.
• Check the Lock Time/Unlock Time to check if rating restrictions are disabled.
• Rating restrictions apply only to content on ANT 1 and ANT
2, and VIDEO composite video jacks.
• Not all broadcasters send ratings. Contact your local
broadcaster or cable provider.

On-screen displays appear each time you
change a function.

Normal TV operation.

I am using CEC for my HDMI devices but control •
is erratic and I wish to disable it.
•
•

If you are unable to correct a problem with your TV,
consult your Mitsubishi dealer or Mitsubishi Consumer Relations at (800) 332-2119.

Turn off the TV’s CEC control. See Inputs > Name menu,
page 50.
Disable CEC on the device itself (see the device’s instructions),
If the problem persists, even after disabling the device’s
CEC, do the following:
1. Disconnect the device from the TV.
2. Open the Inputs > Name menu. Highlight the device
and select Delete to remove the device from the Input
Selection menu.
3. Reconnect the device to the TV and Auto Input Sensing
will recognize the device as a non-CEC device.

TV Channels
1.

Symptom

Remarks

The TV takes several seconds to respond to
channel changes.

•
•
•
•

It is normal for digital channels to take longer to tune in.
Press ENTER after a entering channel number to avoid delays.
Use a 4-digit number for an over-the-air digital channel.
Use a 6-digit number for digital cable channels if your cable
service is able to recognize 6-digit channel numbers.

Appendices

Appendix F: Troubleshooting, continued
TV Channels
2.

Appendix F: Troubleshooting, continued
Picture

Symptom

Remarks

You cannot access a channel.

•
•
•
•
•
•

Use number keys instead of CH / .
Be sure the channel you want to view is in memory. See Setup >
Scan on page 44.
Check that the TV is switched to the correct device or antenna for
that channel by pressing the INPUT key.
Make sure Channel Lock is off.
Make sure the Lock > Parent menu lock is set to off.
If you cannot tune to a virtual digital channel even though the
TV has already memorized digital channels, tune to the physical
channel number used by the broadcaster. The virtual channel will
then be automatically added to memory.

Name options are not available for some
channels.

You can name only memorized analog channels and memorized
digital channels not named by the broadcaster.

When ChannelView list is displayed, information appears incomplete

•
•

Available information is sent from the broadcaster or cable
provider. No other data is available.
Make sure the TV clock is set correctly.

Symptom

Remarks

You cannot view a picture when playing a
VHS tape.

Check your VCR’s owner’s guide for further troubleshooting.

VCR or DVD player’s on-screen menus jitter
up and down.

Possible cause: Many VCRs and DVD players provide onscreen menus at only half-resolution. These lower-resolution
graphics may appear to jitter up and down when the TV converts them to high-definition graphics.

When viewing a stopped VCR, white lines
are rolling on the screen.

•
•
•

A color program appears as a black and
white image, or the colors are dim, or the
screen is black.

The PerfectColor color balance has been incorrectly set. Reset
the PerfectColor balance.

Picture from an HDMI input is noisy (poor
quality).

•
•

The image from a computer appears distorted when viewed on the TV.

Normal TV operation. The TV does not correct distortion in the
picture from a computer because the correction process may
cut off the edges of the image.

TV Power On/Off
1.

Symptom

Remarks

TV takes an excessively long time to power
on.

•
•

You cannot program the TV to turn on automatically (Timer function)

•
•
•

When switched on, the TV needs time to boot up, just as a
computer does.
TV Energy Mode is set to Low Power. Change TV Energy
Mode to Fast Power On in the Setup menu.

The TV will not turn on after being plugged in. If light on front panel is blinking, wait at least one and a half
minutes for the light to turn off, then press POWER again.

TV turned itself off and the light on the front
panel started to blink.

•
•

Momentary power fluctuation or unusual digital signal
caused the TV to turn off to prevent damage. Wait for the
green light to stop flashing and turn the TV on again.
If the TV does not stay on, use the System Reset button on
the control panel. If this happens frequently, obtain an AC
line power conditioner/surge protector.

TV turned itself off and the STATUS light is a
steady red.

The TV has overheated. Clear blocked air vents and ensure at
least four inches of clearance on all sides of the TV.

TV will not power off.

Use the System Reset button.

Remarks

Picture does not look like a high-definition
picture.

Not all signals are high-definition signals. To receive high-definition programming from your cable or satellite provider, you must
subscribe to the provider’s high-definition service. Some overthe-air broadcasts are in high-definition and can be received with
a high-quality antenna suited to your location.

There is a large black or gray rectangle on
the screen.

The TV’s analog closed captioning has been set to text mode in
the Captions menu. Turn off text mode because there is no text
information being broadcast.

Try using a different HDMI cable.
If the signal is 1080p, upgrade a Category 1 (unmarked)
HDMI cable to a Category 2 high-speed HDMI cable.

Symptom

Remarks

There is no sound even when the
volume is turned up.

•
•
•
•
•

Check if the MUTE button is on.
The TV’s “Listen to:” audio setting may be set to SAP.
Check that the Speakers option is set to TV to hear sound from the
TV speakers.
If using an A/V receiver, check that the Speakers option is set to AV
Receiver to hear sound from the A/V receiver speakers.
Perform a System Reset.

I set the Speakers option to AV
Receiver, but hear sound from the TV
speakers instead of the A/V receiver.

Make sure the A/V receiver is connected to one of the TV’s audio
outputs (AVR AUDIO OUTPUT or DIGITAL AUDIO OUTPUT).

The sound does not match the screen
picture.

The TV’s Listen to: setting may be set to SAP. See page 42.

The sound from my A/V receiver does
not match the screen picture (I should
hear the correct audio from my A/V
receiver).

•

Picture
Symptom

Turn off video mute for the VCR.
Begin playing the tape.
Change the VCR input to the antenna input.

Sound (see also NetCommand troubleshooting for additional help with A/V receiver concerns)

The TV may be locked.
The clock may not be set.
TV Energy Mode is set to Low Power. Change to Fast
Power On in Setup menu.

•

The sound from my A/V receiver does
•
not match the screen picture (my source
device should be sending both audio
and video through the A/V receiver).
•

Cannot select an audio-only device; it
does not appear in the Input Selection
Menu.

Check that DIGITAL AUDIO OUTPUT and/or AVR AUDIO OUTPUT
on TV’s main panel is connected to the A/V receiver.
Without this connection, devices connected only to the TV (and
not the A/V receiver) can be heard only from the TV speakers.
Note that this includes the ANT 1/ANT 2 inputs, a device (such as
a camcorder) connected to the convenience jacks, and any other
device sending audio to the TV only.
Check A/V receiver input selection in the Inputs > AVR menu. If
NetCommand is set up incorrectly for the A/V receiver, see “A/V
Receiver Control: Automatic Audio Switching,” page 61.
Check A/V receiver input selection in the Inputs > AVR menu.
If NetCommand is set up incorrectly for the A/V receiver, see
“Setup to Control Automatic Audio and Video Switching via
HDMI,” page 64.
The TV’s Listen to: setting may be set to SAP. See page 42.

Plug a video plug into any composite VIDEO jack for the Auto Input
Sensing screen to appear. See “Audio-Only Device,” page 28.

Appendices

Appendix F: Troubleshooting, continued

Indicators

NetCommand IR Control

Symptom

Remarks

Symptom

STATUS indicator light is a steady red.

•

•
2.

STATUS indicator light is a steady/flashing
red.

•
•
•

Room temperature has exceeded proper levels. Cool the
room.
The TV has overheated. Clear blocked air vents and ensure at
least four inches of clearance on all sides of the TV.

NetCommand IR Control
Symptom

Remarks

•

Cannot see the menu from the A/V Receiver.

•
•

NetCommand unable to learn specific device
keys.

•
•
•
•
•

A/V Receiver Set Up for Audio-Only Switching
The A/V Receiver is not connected to any video input of
the TV. To check the A/V Receiver menu, temporarily plug
into an unused input of the TV, such as Input 3. Exit the
Auto Input Sensing screen and select Input 3 from the Input
Selection menu. Press MENU.
A/V Receiver Set Up for Audio and Video Switching over HDMI
Use the MENU key on the A/V receiver’s remote control.
A/V Receiver with NetCommand for HDMI.
Press INPUT to open the Input Selection menu. Highlight
the A/V receiver icon and press MENU.
A/V Device does not use IR format for remote control
signal. ITT and RF formats cannot be learned.
Room lighting may affect the signal. Have the remotes very
close (6 inches or less) to the TV during Learning.
If learning a Mitsubishi remote control, make sure slide
switch is not set to TV position.
Some, but not all, device key functions can be learned by
NetCommand. For example, POWER and PLAY may be
learned, but other functions may not.
The signal from the remote control may not be strong
enough. Insert fresh batteries and try Learning again.

Remarks

The A/V receiver is the selected audio source •
but there is no sound.
•

Unplug set from AC power. Plug back in and wait one minute
for blinking to stop.
Press SYSTEM RESET button and wait for blinking to stop.
If blinking continues, service is required. Contact your dealer
or a Mitsubishi Authorized Service Center to arrange for a
service evaluation. Listings of Mitsubishi Authorized Service
locations can be obtained from our web site, www.mitsubishi-tv.com or by calling 1-800-332-2119.

•

Check to see if the A/V Receiver power is turned on.
A/V Receiver Set Up for Audio-Only Switching
-- With A/V receiver power turned on, redisplay the
Input Selection menu and press ENTER to allow
NetCommand to correctly select the A/V Receiver
input.
-- Incorrect setup in the Inputs > AVR menu. Check the
device connection assigned in the AV Receiver menu.
A/V Receiver Set Up for Audio and Video Switching over HDMI
-- If the device is connected only to the TV (e.g., on ANT1,
ANT 2, or the convenience jacks), verify that the TV’s
AUDIO OUTPUT is connected to the A/V receiver.
-- The A/V receiver is not switching properly because
you have not learned the inputs. See “Setting Up
NetCommand Control of an A/V Receiver,” page 60.

There is no sound from the A/V receiver
for my DVD player or other surround sound
device even though I learned the IR code for
the A/V receiver’s DVD input or other input.
(A/V Receiver Set Up for Audio-Only Switching)

NetCommand A/V receiver setup for the DVD player or digital
surround sound device or other device is not switching properly. See chapter 6, “NetCommand IR Control,” and perform
A/V receiver setup for a digital surround sound device as
described under “A/V Receiver Control: Automatic Audio
Switching,” page 61.

There is no sound or picture from the A/V
receiver for my DVD player or other device
connected to the A/V receiver; the A/V
receiver should be sending video to the TV
over an HDMI cable.
(A/V Receiver Set Up for Audio and Video
Switching over HDMI)

NetCommand A/V receiver setup is not switching audio and
video inputs properly. See “Setup to Control Automatic Audio
and Video Switching via HDMI,” page 64.

I’ve selected my DVD player or other surround sound device in combination with the
TV speakers but hear no sound from the TV
speakers.

•

A/V Receiver Set Up for Audio-Only Switching
If you have only an audio connection from the device to the
A/V receiver, a physical audio connection from the device
to the TV is also required.
-- Connect the left and right audio output from the device
to the appropriate TV audio input. Now you can hear
audio from the device through either the TV speakers or
the A/V receiver.
to
-- To switch audio sources, press AUDIO, press
show the Speakers option, then press to select AV
Receiver or TV.
A/V Receiver Set Up for Audio and Video Switching over HDMI
With your DVD player connected to the A/V receiver, only
video is passed from the A/V receiver to the TV because of
copy-protection restrictions on the HDMI signal

I “learned” the RECORD key for my VCR/DVR Check that the VCR or DVR is receiving a signal directly from
but when I pressed the RECORD key, the
your cable box or satellite receiver.
VCR/DVR did not record anything.

Trademark and License Information

Trademark and License Information
LICENSOR’S SUPPLIERS DO NOT MAKE OR PASS ON TO END USER OR ANY OTHER THIRD PARTY, ANY
EXPRESS, IMPLIED OR STATUTORY WARRANTY OR REPRESENTATION ON BEHALF OF SUCH SUPPLIERS,
INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, TITLE, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
CableCARD™ is a trademark of Cable Television Laboratories, Inc.
FlashFX ProT is a trademark of Datalight, Inc. Datalight® is a registered trademark of Datalight, Inc. Copyright 1989-2008
Datalight, Inc., all rights reserved.
Manufactured under license from Dolby Laboratories. “Dolby” and “Pro Logic” are trademarks of Dolby Laboratories.
GalleryPlayer® and the GalleryPlayer logo are either registered trademarks or trademarks of GalleryPlayer, Inc., in the United
States and/or other countries.
HDMI™ the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
The software in this TV is based in part on the work of the Independent JPEG Group, copyright © 1991-1998, Thomas G. Lane, all
rights reserved.

The

logo and the words “Simplay™” and “Simplay HD™” are the trademarks of Silicon Image, Inc.

In the United States, TV Guide and other related marks are registered marks of Gemstar-TV Guide International, Inc. and/or one of
its affiliates.
The TV Guide Daily system is manufactured under license from Gemstar-TV Guide International, Inc. and/or one of its affiliates.
The TV Guide Daily system is protected by one or more of the following United States patents 6,498,895; 6,850,693; 6,396,546;
5,940,073; 6,239,794 to Gemstar-TV Guide International, Inc. and/or its subsidiaries.
Gemstar-TV Guide International, Inc. and/or its related affiliates are not in any way liable for the accuracy or availability of the program
schedule information or other data in the TV Guide Daily system and cannot guarantee service availability in your area. In no event shall
Gemstar-TV Guide International, Inc. and/or its related affiliates be liable for any damages in connection with the accuracy or availability
of the program schedule information or other data in the TV Guide Daily system.
x.v.Color and the x.v.Color logo are trademarks of Sony Corporation.
ChannelView™, DeepField™ Imager, Easy Connect™, NetCommand®, PerfectColor™, Plush 1080p®, QuickView™, SharpEdge™,
Smooth120Hz™ are trademarks of Mitsubishi Digital Electronics America, Inc.

Trademark and License Information

Mitsubishi TV Software
END-USER LICENSE AGREEMENT FOR EMBEDDED SOFTWARE
IMPORTANT – READ CAREFULLY: This License Agreement is a legal agreement between you (either an individual or an entity) and
Mitsubishi Digital Electronics America, Inc. (MDEA) for all software pre installed and/or provided along with this television (“Software”).
By utilizing this television and Software, you agree to be bound by the terms of this License Agreement.
The Software is protected by United States copyright laws and international treaty provisions, as well as other intellectual property laws
and treaties. The Software is licensed, not sold.
1.
LICENSE GRANT. MDEA grants you a non-exclusive, non-transferable, limited right and license to use one copy of the Software
only with the Mitsubishi television model that included this owner’s guide and owned by you.
2.
RIGHTS AND LIMITATIONS.
Software Not for Resale. You may not resell or otherwise transfer for value the Software, except in conjunction with a sale of the TV that
Software has been pre installed.
Prohibition on Reverse Engineering, Decompilation and Disassembly. The Software contains trade secrets or other proprietary material
in its human perceivable form and to protect them, you may not reverse engineer, decompile, or disassemble, or otherwise reduce the
Software to any human perceivable form, except to the extent that the foregoing restriction is expressly prohibited by applicable law.
Separation of Components. The Software is licensed as a single product. Its component parts may not be separated for use on more
than one TV.
No Rental. You may not rent, lease, lend, or sublicense the Software.
Trademarks. This License Agreement does not grant you any rights to any trademarks of MDEA.
3.
VIOLATIONS. You understand that any use, copying or transfer of the Software, except as permitted pursuant to this License,
may subject you to serious criminal and civil penalties including damages and an award to MDEA of attorneys’ fees in connection with
any violation of this License. You further understand that you may be held legally responsible for any copyright infringement or other
violation of intellectual property rights that is caused, encouraged, or induced by your failure to abide by the terms of the License. This
license is effective until terminated, and will terminate immediately without notice from MDEA or judicial resolution if you fail to comply
with any provision of this License.
4.
COPYRIGHT. All title and intellectual property rights in and to the Software (including but not limited to any images, photographs,
animations, video, audio, music, text, and “applets” incorporated into the Software), and any accompanying printed materials are
owned by or licensed to MDEA. All title and intellectual property rights in and to the content which may be accessed through use of the
Software is the property of the respective content owner and may be protected by applicable copyright or other intellectual property
laws and treaties. This License Agreement grants you no rights to use such content, except that you own the media on which the
Software is recorded, but MDEA and its licensors retain ownership of the Software itself. All rights not expressly granted are reserved
by MDEA.
5.
EXPORT RESTRICTIONS. MDEA is licensing the Software for use within the United States. You agree that you will not export
or re-export the Software. You specifically agree not to export or re-export the Software: (i) to any country to which the U.S. has
embargoed or restricted the export of goods or services, which currently include, but are not necessarily limited to Cuba, Iran, Iraq,
Libya, North Korea, Sudan, and Syria, or to any national of any such country, wherever located, who intends to transmit or transport the
Software back to such country; (ii) to any person or entity who you know or have reason to know will utilize the Software in the design,
development, or production of nuclear, chemical, or biological weapons; or (iii) to any person or entity who has been prohibited from
participating in U.S. export transactions by any federal agency of the U.S. government. You warrant and represent that neither the BXA
nor any other U.S. federal agency has suspended, revoked, or denied your export privileges.
6.
DISCLAIMER OF WARRANTY. EXCEPT AS OTHERWISE PROVIDED IN THIS LICENSE OR IN THE LIMITED WARRANTY
APPLICABLE TO THE TV, MDEA MAKES NO OTHER WARRANTIES OF ANY KIND WHATSOEVER REGARDING THE SOFTWARE
AND HEREBY EXPRESSLY DISCLAIMS ALL WARRANTIES OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED, WITH
RESPECT TO THE SOFTWARE. ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXPRESSLY DISCLAIMED BY MDEA. IN
NO EVENT SHALL MDEA BE LIABLE TO YOU OR ANY THIRD PARTIES, IN CONTRACT, IN TORT OR OTHERWISE, FOR ANY
DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND OR NATURE. BECAUSE SOME
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IMPLIED WARRANTIES, THE ABOVE LIMITATION MAY
NOT APPLY TO YOU.
7.
LIMITATION OF LIABILITY. MDEA SHALL NOT, UNDER ANY CIRCUMSTANCES BE LIABLE TO YOU OR ANY THIRD
PARTIES FOR ANY DAMAGES OF ANY NATURE, WHETHER INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL
OR OTHERWISE, INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOST PROFITS, LOSS OF GOOD WILL OR
EXPENDITURES MADE OR COMMITTED FOR IN RELIANCE ON THE CONTINUATION OF THIS LICENSE. YOU AGREE THAT
NEITHER MDEA’S BREACH OF THIS LICENSE NOR ITS FAILURE TO REPAIR A DEFECT, ERROR OR BUG SHALL CONSTITUTE
A FAILURE OF THE ESSENTIAL PURPOSE OF THIS LICENSE. BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATIONS MAY
NOT APPLY TO YOU. MDEA’s liability to you for direct damages for any cause whatsoever and regardless of the form of the
action, will be limited to the money paid by you for the TV (based on fair market value of the TV) that caused the damages.
8.
GENERAL. This License Agreement will be governed by the laws of the State of California.

Warranty

MITSUBISHI LCD FLAT PANEL HDTV LIMITED WARRANTY
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. (“MDEA”) warrants to the original purchaser of this LCD Flat
Panel HDTV that if purchased from an authorized MITSUBISHI Audio/Video Dealer, should it prove defective by
reason of improper workmanship and/or material:
a. Parts. All parts (except any software incorporated into this HDTV are warranted for a period of one year from
the date of the original purchase at retail. We will repair or replace, at our option, any defective part without charge
for the part. Parts used for replacement may be replaced with those of like kind and quality and may be new or
remanufactured. Parts used for replacement are warranted for the remainder of the original warranty period.
b. Embedded Software. MDEA warrants that all software incorporated into this HDTV (the “Embedded Software”)
will perform in accordance with the functional description of Embedded Software in all material respects, but
MDEA does not warrant that the Embedded Software is error-free. MDEA also does not warrant that the Embedded
Software will be compatible under IEEE 1394 AV/C and HAVi software standards with products produced by any
other manufacturer. The warranty contained in this section shall continue for a period of one year, from the date of
the original purchase from the dealer. If, after prompt notice within the warranty period, MDEA determines that the
Embedded Software has failed to perform in accordance with such functional description in all material respects and
if such failure is not due to accident, misuse, modification or misapplication of the Embedded Software, then MDEA
shall modify or replace the nonconforming Embedded Software at no charge to you, which at MDEA’s sole discretion
may be fulfilled by means of modification or replacement software contained on a replacement memory card for
Customer installation. The foregoing shall be MDEA’s sole obligation to you under this limited warranty. All rights
under this limited warranty on the Embedded Software also subject to your compliance with the terms of the Software
License Agreement applicable to this HDTV, and this limited warranty on the Embedded Software shall be null and
void if the Embedded Software is modified or changed in any manner except as specifically authorized by MDEA.
c. Labor. For certain items that are designed to be replaced by the consumer, including (but not limited to) some
Embedded Software, the consumer is solely responsible for any replacement labor. For all other parts, we will provide
the labor for a warranty repair by an authorized MITSUBISHI service center without charge for one year from the
original date of purchase at retail.
d. Notice. To obtain warranty service, you must notify an authorized MITSUBISHI service center of any defect within
the applicable warranty time period.
BEFORE REQUESTING SERVICE, please review the TV owner’s guide to insure proper installation and
correct customer control adjustment. If the problem persists, please arrange for warranty service.
1. TO OBTAIN WARRANTY SERVICE:
a. Contact your nearest authorized MITSUBISHI service center whose name and address can be obtained from your
MITSUBISHI dealer, by writing to the address provided below, calling MDEA at 800-332-2119, or using the support
feature of our website at www.Mitsubishi-tv.com.
b. Warranty service will be provided in your home or, if required, at an authorized service shop, provided that your
television is located within the geographic territory customarily covered by an authorized MITSUBISHI service center.
If not, you must either deliver your television to an authorized service location at your own expense, or pay for any
travel and/or transportation costs the service center may charge to and from you home. Actual service labor will be
provided without charge.
c. Proof of purchase date from an authorized MITSUBISHI dealer is required when requesting warranty service.
Present your sales receipt or other document which establishes proof and date of purchase. THE RETURN OF THE
OWNER REGISTRATION CARD IS NOT A CONDITION OF WARRANTY COVERAGE. However, please return the
Owner Registration Card so that we can contact you should a question of safety arise which could affect you.
2. THIS LIMITED WARRANTY DOES NOT COVER:
a. Up to .01% pixel outages (small dot picture elements that are dark or incorrectly illuminated).
b. Cosmetic damage or any other damage where such damage is caused by unauthorized modification, alteration,
repairs to or service of the product by anyone other than an authorized MITSUBISHI service center; physical abuse
to or misuse of the product (or any product damaged by excessive physical or electrical stress); any products that
have had a serial number or any part thereof altered, defaced or removed; product use in any manner contrary to
the Owner’s Guide; freight damage; or any damage caused by acts of God or other factors beyond the reasonable
control of MDEA, such as power surge damage caused by electrical system or damages caused by use of third party
mounting brackets or stands. This limited warranty also excludes service calls where no defect in the product covered
under this warranty is found, service calls related to unsatisfactory audio or visual reception or signal unless caused
by a defect in the product that is covered under this limited warranty, all costs, expenses or any other damages

Warranty

arising from product installation, removal from or re-installation into custom installations or on wall mountings, or
set-ups, any adjustments of user controls (including contrast, brightness, color, tint, fine tuning, sharpness), other
adjustment necessary to prepare the unit for display or use, connection with any external audio receiver, antenna,
cable or satellite systems, or service of products purchased or serviced outside the U.S.A.
Please consult the operating instructions contained in the Owner’s Guide furnished with the product for information
regarding user controls.
3. ANY EXPRESS WARRANTY NOT PROVIDED HEREIN, AND ANY REMEDY WHICH, BUT FOR THIS PROVISION,
MIGHT ARISE BY IMPLICATION OR OPERATION OF LAW, IS HEREBY EXCLUDED AND DISCLAIMED. THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR ANY PARTICULAR PURPOSE ARE EXPRESSLY
LIMITED TO A TERM OF ONE YEAR.
4. UNDER NO CIRCUMSTANCES SHALL MDEA BE LIABLE TO PURCHASER OR ANY OTHER PERSON FOR ANY
INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER ARISING OUT OF BREACH OF WARRANTY,
BREACH OF CONTRACT, OR OTHERWISE.
5. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of
incidental, special, or consequential damages, so the above limitations or exclusions may not apply to you.
6. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to
state.
7. In the event of any dispute under this limited warranty, jurisdiction and venue for resolving that dispute will be in the
state where the television was purchased and the laws of such state will govern.
In no event shall Mitsubishi have any liability, including with out limitation, for general, consequential, incidental, or
special damages for loss, destruction, damage or corruption of recorded data, media or software resulting from use
of this television, or cost of recovery of lost data, media or software therefore.

MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC.
9351 Jeronimo Road
Irvine, CA 92618-1904

Index

Index
A

Adjust Keys (Up/Down/Left/Right)
30, 37
Anamorphic Picture Format 34
Antenna
Connecting 24
Signal Strength for Digital Channels 32
Antenna Inputs (ANT 1, ANT 2) 9
Audio Lock (A/V receiver control) 70
AUDIO OUTPUT Jacks 10
Auto Input/Auto Output Sensing 14,
16
Auto-Off (Sleep Timer) 29
Auto-On (Timer) 47
A/V Memory Reset 83
A/V Receiver
and TV Speakers 42
and TV’s Remote Control 60, 64,
69
Audio Lock 70
Connecting 10, 27
Controlling Sound Volume 16
Disconnecting Analog 16
NetCommand IR Control 54, 58,
60
Controlling a Device Connected
to the A/V Receiver 17, 65
Video and Audio Switching via
HDMI 64

A/V Reset 7, 83

Backlight (Video Setting) 40
Batteries 12
Blue Glow 39
Brightness (picture adjustment) 40

Cable Box
and TV’s Remote Control 31, 69
Connecting 22, 23, 25, 26
CableCARD 9, 20, 24, 48
Channel Memorization 14
Cable Management 21
Camcorder 28
Captions Menu 43
CEC (Consumer Electronics Control)
7, 17, 69
A/V Receiver 16, 81, 88
CEC-Enabled Devices and the
Inputs Name menu 50
Disabling CEC for a Device 50
NetCommand for HDMI/CEC 80
Troubleshooting 85

Index
Channels
Add Single Channel to Memory
44, 45
antennaweb.org 44
Changing Channels 29
Channel Lock 45
Digital Channel Numbers 66
Edit Channels (menu) 45
Favorites (Fav) 33, 45
Memorizing 14, 44
Naming 45
Physical/Virtual Channel Numbers 44, 45
Scan (memorize) 44
Status Display 32
Troubleshooting 85
ChannelView Channel Listings 31
Cleaning 5
Clock, Set Date and Time 46
Closed Captions 43
Color Adjustments 38, 40
Reset Color 38, 83
Computer
and Display Formats 19, 66
Connecting 18
Contrast 40
Controller Output 10
Control Panel Lock 53
Customer Service and Support 84

Date. See Clock
DeepField Imager (video adjustment)
41
Defaults, Resetting 83
DIGITAL AUDIO OUTPUT 10
Dolby Digital 10, 27, 61, 66
DVD Player
and TV’s Remote Control 31, 69
Connecting 22, 23
DVI Device, Connecting 23

GalleryPlayer 35, 49
Game
Game as Input Name 50
Game Picture Mode 40
HDMI Cables for Games 10
Global Menu 39
GUIDE Key 30, 69
ChannelView 31
TV Guide Daily 77

HD (High-Definition) Signal) 34
HDMI
Changing Out an HDMI Device
and Auto Input Sensing 16
Connecting an HDMI Device 22
A/V Receiver 27

HDMI Cable Categories 10
HDMI Jack 10
NetCommand for HDMI Devices
7, 69, 82, 88
Removing an HDMI Device from
the Input Selection Menu 50

INFO Key
ChannelView 31
in TV Menus 37
Status Display 32
USB Photo Menu 35
Input Selection Menu
Choose Viewing Source 29
Disconnected HDMI Device 16,
50, 82
Icon Order 50
INPUT Key 30
Inputs Menu 50
Inputs > Name Menu and CEC
Devices 82
IR (infrared) Emitter Placement
55

Edit Menu (channels) 45
Energy Mode 48

F1–F4 Keys 30, 56
Fast Power On 20, 48, 77
FAV (Favorite Channels) 33, 45
Film Mode 39
Font (digital closed captions) 43
Freeze Picture 31
Front Panel
Blue Glow 39
Indicators 8
Full Native 34

JPEG Photo Files 35
Language
in Digital Programs 42
SAP (Second Audio Program) 42
Language Menu 44
Learn 50. See also NetCommand IR
Control
Learn Menu 50
Letter Box Image Display 34
Level Sound 42
Light, Decorative 39
Listen To (Audio setting) 42

Listings
ChannelView 31
TV Guide Daily 76
Lock TV
Bypassing the Lock 67
Lock by Channel 45
Lock by Ratings 52
Lock by Time 53
Lock Control Panel 53
Preset V-Chip Blocking 51
Low Power (Energy Mode) 48
Wired IR option 10

Main Panel 9, 10
Media Setup Menu 36
Memorizing Channels 14, 44
Memory Reset, A/V 83
Mute
Closed Captions 43
MUTE key 30
Video Mute 39

Name (Inputs > Name menu) 50
NetCommand for HDMI Devices 7,
69, 80, 82
NetCommand IR Control
About 54
A/V Receiver Control 60
Compared to Programming the
Remote Control 69
Initial Setup for Most Devices 56
Operating 58, 59
Specialized Device Keys 57
Troubleshooting 88
Noise, Video 40

Order Menu (Inputs > Order) 50

Parent Menu 52
Pass Code
Resetting 67
Setting 51
PAUSE Key 31
PC (personal computer). See Computer
PerfectColor 38
PerfectTint 38, 83
Photo Viewing 36
Physical Channel Number 45
Picture
AV Menu Controls 38
Picture Quality and Film Mode
39
Troubleshooting 86

Picture Mode 40
Power Consumption
Energy Mode 48
Power On/Off
Troubleshooting 86

QV Key (QuickView™) 30
and FAV Key 33

Ratings (TV and Movie) 52
Set Viewing Restrictions 51
Remote Control
Keys and Functions 30, 31
Programming Codes (reference
chart) 71
Programming, Compared to
NetCommand “Learning” 69
Programming Instructions 70
Reset 31
Reset
AV Menu Reset (by input) 38
A/V Reset (all settings) 7
Color 83
Pass Code 67
Remote Control 31
Remote Control Audio Lock 70
System Reset 7
TV Reset Comparison Guide 83
RS-232C 10

Safety Instructions 4, 5
SAP (second audio program) 42
Satellite Receiver
and the Remote Control 69
Connecting 22, 23
Scan (memorize channels) 44
Screen Saver 39
SD (Standard-Definition Signal) 34
Setup Menu 44
SharpEdge (video adjustment) 41
Signal Definitions 34
Signal Strength Indicator 32
Sleep Timer 29
Smooth120Hz Film Motion 6, 39
Video Noise Settings 40
Software Updating 5
Sound
Audio Menu 42
Controlling A/V Receiver Volume
16, 60, 64
Level Sound 42
Sound Mode (audio effects) 42
Speakers Option 42
Specifications, TV 66
Standard-Definition Signal 34
Stand Removal 11

Status Display 32
Stereo System. See A/V Receiver
Subwoofer (Audio Menu) 42
SUBWOOFER Jack 10, 16
Surround Sound 27, 62, 63
Simulated Surround Sound 42
S-Video
Connecting 23, 25
S-VIDEO Jack 9
System Reset 7, 84

Time. See Clock
Timer (auto-on) 47
Time Zone. See Clock
Troubleshooting 83
TV Guide Daily
Access Requirements 5
Channel Memorization 44
Setup 76, 77
Troubleshooting 79
TV Energy Mode 48

V-Chip Ratings
Applying Restrictions 51
Definitions 52
In Status Display 32
VCR
Connecting 9, 25
Troubleshooting 87
Vert Adjustment 41
Video from a Digital Camera 36
Video Game. See Game
Video Menu 40
Video Mute 39
Video Noise 40
Viewing Device. See Input Selection
Menu
Virtual Channel 45

Wall Mount Kit 11
Wall Outlet Cable 24

x.v.Color 10, 22, 40

ZIP code 77

Website:

www.mitsubishi-tv.com

E-mail:

MDEAservice@mdea.com

For questions, call Consumer Relations at
800-332-2119
To order replacement or additional
remote controls or Owner’s Guides
Visit our website www.mitsuparts.com
or call
800-553-7278

SYSTEM RESET
If the TV does not respond to the remote control,
control-panel buttons, or will not power on/off, press
the SYSTEM RESET button on the control panel.
The green LED will flash quickly for about one
minute. When the green LED stops flashing, you
may turn on the TV. Settings changes you made
most recently, before using SYSTEM RESET, may be lost.

Written and Printed in U.S.A.
VLP39+, VLP39+++

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c006 1.236519, Wed Jun 14 2006 08:31:24
Create Date                     : 2008:06:20 13:13:39-07:00
Modify Date                     : 2008:06:20 13:14:28-07:00
Metadata Date                   : 2008:06:20 13:14:28-07:00
Creator Tool                    : Adobe InDesign CS3 (5.0.2)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 9463 bytes, use -b option to extract)
Version ID                      : 1
Instance ID                     : uuid:31f5e420-ad6e-42d9-881e-236f493cf1a5
Document ID                     : adobe:docid:indd:4109e6c6-3e25-11dd-aa0c-a27af0be41e0
Rendition Class                 : proof:pdf
Derived From Instance ID        : 4109e6c5-3e25-11dd-aa0c-a27af0be41e0
Derived From Document ID        : adobe:docid:indd:4109e6c4-3e25-11dd-aa0c-a27af0be41e0
Derived From Version ID         : 1
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 200.00, 72.00, 200.00, 200.00, 200.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 200.00, 72.00, 200.00, 200.00, 200.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:361e7d19-db53-481d-83c1-41af29dc77c3, uuid:37c84421-1d16-41c8-b96e-38fd72747256, uuid:60dd11ca-3e10-47ae-8f29-e1a53b326576, uuid:8d27cb8e-6426-4225-b31e-f9aacf9eb007, uuid:9dcaa4be-2b1d-44e8-8839-87930baa8039, uuid:59f623b0-0799-4880-adb9-55d9ae54b9b5, uuid:87e6df43-1237-42e4-a5db-ccb5f3953d85, uuid:feaee984-344c-468f-8bd3-12b72678c06d, uuid:8175d174-b0ca-4b14-83f6-7cee84bd77d8, uuid:a881e7f9-e94e-480b-aeeb-59fcaca2a7d3, uuid:6cd26871-8b5d-496a-a56d-3a60ec135de0, uuid:9f1833e5-4961-4f0b-8a0d-2ed0e5ee9948, uuid:90427ef0-622a-4a54-acbb-5639a3193388, uuid:259ad4aa-4627-45ae-a419-c53d38c03633, uuid:19c9d208-af58-43c5-931b-ea4600b0e992, uuid:1374c6cc-219a-4fa7-aa63-11e0c2515079, uuid:c52d8506-51a7-4b8d-83a2-36a3752a92ed, uuid:25e9e269-5ced-429b-9887-17b3748df8cf, uuid:9f1833e5-4961-4f0b-8a0d-2ed0e5ee9948, uuid:4878bd9a-44a6-4254-8824-933e42968c30, uuid:aae8b890-ef41-47bc-85e2-095b42e00ced, uuid:8175d174-b0ca-4b14-83f6-7cee84bd77d8, uuid:8175d174-b0ca-4b14-83f6-7cee84bd77d8, uuid:58bc17ed-ba6b-4877-b871-6cda1db30eb0, uuid:f27e9503-5e05-489a-9a35-50d5a214d0cb, uuid:fd89589f-f046-44c5-8d7d-f3271839ae56, uuid:7d05310d-852b-451d-a79e-a30ef325665d, uuid:7e9e6e22-d7e9-479a-84c9-8ea7ee3666e2, uuid:0b3d5758-503d-4e09-8ccc-645ed4bfa952, uuid:1005d59e-dcaa-475c-a99f-e85feaac5b3b, uuid:7b4fcdea-fdf2-4211-a319-9b3bb0a80e82, uuid:6cbef37d-d0fa-11dc-8a27-fb6b64813dba, uuid:406eadc7-f482-11dc-b97a-90185018ca8f, uuid:406eadc7-f482-11dc-b97a-90185018ca8f, uuid:406eadc7-f482-11dc-b97a-90185018ca8f, uuid:998e68d3-fd27-11dc-a002-a50105bab3dd, uuid:998e68d3-fd27-11dc-a002-a50105bab3dd, uuid:04daafb7-3ab5-460f-8530-7dfc3e1f0d00, uuid:04daafb7-3ab5-460f-8530-7dfc3e1f0d00, uuid:04daafb7-3ab5-460f-8530-7dfc3e1f0d00, uuid:04daafb7-3ab5-460f-8530-7dfc3e1f0d00, uuid:04daafb7-3ab5-460f-8530-7dfc3e1f0d00, uuid:bda09830-8854-40ff-b8eb-7bd462df27e4, uuid:afeceb76-69ae-4510-a003-8d7dc4a9f3d2, uuid:3dfb0a3a-ac6f-402b-8e49-fd5ecfcd9371, uuid:8f3fbf19-035d-480b-8377-09d56c48b790, uuid:5b238618-17d6-443e-a5a9-6c01da59ad24, uuid:005430f2-8f6e-40fc-ba96-4a80afbcd5a2, uuid:5f7e60a2-2821-4307-8bba-d4ddd145a800, uuid:5f7e60a2-2821-4307-8bba-d4ddd145a800, uuid:a9a98633-ec95-4d0c-8c4c-3da1a9e3fc0c, uuid:829bb72a-e9f7-4fe6-845d-4c0eba376846, uuid:945c26eb-959f-49d4-a716-7bcf11fa457f, uuid:fd89589f-f046-44c5-8d7d-f3271839ae56, uuid:2fbbd8c2-f83e-4254-a254-40c502d2faaa, uuid:5cf12b82-4a06-4269-848e-b95524ee8dda, uuid:fddf86ee-4239-4418-91a0-5701e386cec7, uuid:0e464a9d-7b75-45ac-bd77-cba4a8dcde8e, uuid:116c4d47-29c0-4d7c-a13e-6c064fd76cd4, uuid:49cb07d9-a7a0-444b-8a87-ae7425c5ab48, uuid:31426878-be8f-4f83-968d-8feb31a9589b, uuid:6f8da720-0a08-4615-a306-544a61d33268, uuid:e9db7c48-60c2-4fd9-994a-a8bc57da2d31, uuid:7ff79c6b-2c9b-4a77-8cdc-2023ff9d3367, uuid:ee870051-b676-4e1f-88f8-8e7482f076f2, uuid:441fd60d-8063-42a4-99ae-da30228d0703, uuid:9f1833e5-4961-4f0b-8a0d-2ed0e5ee9948, uuid:470768a2-f53b-11dc-b97a-90185018ca8f, uuid:00f7bad7-12ef-4044-b25a-e4e9e87bea2c, uuid:7cea744c-0a31-11dc-a2df-de8e205f211a, uuid:6f34bd8d-570a-43b3-a330-1eecb9a70a58, uuid:8aa0b241-e502-11da-9e33-c7eab616b17a, uuid:9f1833e5-4961-4f0b-8a0d-2ed0e5ee9948, uuid:c0781ec7-b656-4819-b113-1f0fe340b79f, uuid:83ed19c6-f53a-11dc-b97a-90185018ca8f, uuid:208d999a-dbfc-11dc-9b9a-81a0fb521c58, uuid:d22f5b01-27bd-4670-9026-7491f73c057d, uuid:d615c778-fcdd-4b95-b08f-d7484f48294d, uuid:ac5a96f5-914f-11dc-ac6d-fd4b8fe4d062, uuid:ac5a96f5-914f-11dc-ac6d-fd4b8fe4d062, uuid:f1a411b3-d0fa-11dc-8a27-fb6b64813dba, uuid:92f86bb5-d372-11dc-96b0-d239ca376213, uuid:1552b082-e01a-11dc-9593-e619b6fdc8c5, uuid:25a83492-d0fc-11dc-8a27-fb6b64813dba, uuid:6cbef37d-d0fa-11dc-8a27-fb6b64813dba, uuid:5710c426-d0ff-11dc-8a27-fb6b64813dba, uuid:82e48ee3-d108-11dc-8a27-fb6b64813dba, uuid:82e48ee6-d108-11dc-8a27-fb6b64813dba, uuid:516654ad-fabb-11dc-a002-a50105bab3dd, uuid:0f1d5035-fa93-11dc-a002-a50105bab3dd, uuid:11152319-cf95-11dc-9d7d-b8fedb7d8dc0, uuid:e8d93d9c-27d2-4efa-abec-2cca5285e833, uuid:77906f2e-d1d8-4c97-96c2-be1be1227e07, uuid:be3d4992-290d-11dd-ba34-ff05faf10e2d, uuid:be3d4992-290d-11dd-ba34-ff05faf10e2d, uuid:406eadc7-f482-11dc-b97a-90185018ca8f, uuid:406eadc7-f482-11dc-b97a-90185018ca8f, uuid:66b66c99-290e-11dd-ba34-ff05faf10e2d, uuid:66b66c99-290e-11dd-ba34-ff05faf10e2d, uuid:85ab0760-39ef-4ae4-ab95-f2b7a4ad0b24, uuid:45464817-76c7-411f-b4e2-eda46a81ad47, uuid:24f59052-290e-11dd-ba34-ff05faf10e2d, uuid:24f59052-290e-11dd-ba34-ff05faf10e2d, uuid:24f59052-290e-11dd-ba34-ff05faf10e2d, uuid:24f59052-290e-11dd-ba34-ff05faf10e2d, uuid:24f59052-290e-11dd-ba34-ff05faf10e2d, uuid:24f59052-290e-11dd-ba34-ff05faf10e2d, uuid:85ab0760-39ef-4ae4-ab95-f2b7a4ad0b24, uuid:24f59052-290e-11dd-ba34-ff05faf10e2d, uuid:24f59052-290e-11dd-ba34-ff05faf10e2d, uuid:24f59052-290e-11dd-ba34-ff05faf10e2d, uuid:24f59052-290e-11dd-ba34-ff05faf10e2d, uuid:7ff79c6b-2c9b-4a77-8cdc-2023ff9d3367, uuid:66b66c96-290e-11dd-ba34-ff05faf10e2d, uuid:66b66c96-290e-11dd-ba34-ff05faf10e2d, uuid:66b66c96-290e-11dd-ba34-ff05faf10e2d, uuid:66b66c96-290e-11dd-ba34-ff05faf10e2d, uuid:66b66c96-290e-11dd-ba34-ff05faf10e2d, uuid:66b66c96-290e-11dd-ba34-ff05faf10e2d, uuid:66b66c96-290e-11dd-ba34-ff05faf10e2d, uuid:66b66c96-290e-11dd-ba34-ff05faf10e2d, uuid:66b66c96-290e-11dd-ba34-ff05faf10e2d, uuid:04daafb7-3ab5-460f-8530-7dfc3e1f0d00, uuid:5758c49c-ffe0-4bde-93b9-c06fc73c373c, uuid:ac09a788-8af0-457d-bb62-b63f989f87d6, uuid:7a6daa10-fa92-11dc-a002-a50105bab3dd, uuid:be3d498f-290d-11dd-ba34-ff05faf10e2d, uuid:0f1d502f-fa93-11dc-a002-a50105bab3dd, uuid:7a13a075-f985-11db-94d7-8df597580276, uuid:9d278631-e76c-11db-b3ce-e6a58ee09365, uuid:ae5afed4-059e-11dd-a10c-a8354372e141, uuid:ae5afed4-059e-11dd-a10c-a8354372e141, uuid:ae5afeda-059e-11dd-a10c-a8354372e141, uuid:ae5afeda-059e-11dd-a10c-a8354372e141, uuid:66b66c9e-290e-11dd-ba34-ff05faf10e2d, uuid:66b66c9e-290e-11dd-ba34-ff05faf10e2d, uuid:fe4c651f-059e-11dd-a10c-a8354372e141, uuid:fe4c651f-059e-11dd-a10c-a8354372e141, uuid:f8b3eeb7-6107-4a96-88ff-f003f12ab865, uuid:cba2a7ff-291d-11dd-ba34-ff05faf10e2d, uuid:cba2a7fa-291d-11dd-ba34-ff05faf10e2d, uuid:cba2a7fa-291d-11dd-ba34-ff05faf10e2d, uuid:cba2a7fa-291d-11dd-ba34-ff05faf10e2d, uuid:fd89589f-f046-44c5-8d7d-f3271839ae56, uuid:47156e38-14fe-47a8-b9bd-952c388c4b38, uuid:6be66ad2-24ff-45fc-82f7-f2eb54f2a63c
Manifest Reference Document ID  : uuid:10C8B93ADABE11DBBBA5BF98F8380F6A, uuid:1771eeae-6724-11da-8cd0-000a95784b7c, uuid:3249127ADCEBDC118C8ACA3BFFAD6721, uuid:182d88bf-b2cd-4f72-ad47-965180433e8f, uuid:AE6E7892ADF6DC118769CB3E7CADB7CC, uuid:282bdac2-6e96-4f9d-a503-1c6d517f5d2c, uuid:258abee8-4990-4f38-ab30-6db949e527ba, uuid:501a15ec-f503-41df-904c-8f97ae4468db, uuid:f5c7b439-c641-4ec5-ad56-c90a80573352, uuid:b99e6c4e-30b8-44d4-b742-ebe0d2fb97e2, uuid:B06E7892ADF6DC118769CB3E7CADB7CC, uuid:5bfe7a2f-aaf1-415e-a211-1d561852cb3e, uuid:3b7b45ec-5170-4e04-8055-b91edbe46de2, uuid:91755d41-9af5-4c9a-8d10-e0e84116d1c1, uuid:f5c7b439-c641-4ec5-ad56-c90a80573352, uuid:B36E7892ADF6DC118769CB3E7CADB7CC, uuid:DA89EF82D2F9DC119F75B12726087366, uuid:722D86A375FBDC11A9009E93566E5E48, uuid:9F8D75A4511DDD11A2EAE50FCE95C8CA, uuid:1771eeae-6724-11da-8cd0-000a95784b7c, uuid:13cf22fd-ca7d-4675-9537-089fd94bdc69, adobe:docid:photoshop:8b15ee5c-6daf-11da-b06e-a132874f22a6, adobe:docid:photoshop:63383b6f-6db0-11da-b06e-a132874f22a6, adobe:docid:photoshop:9d6ec069-ae63-11dc-a308-a0b8e4b701ed, adobe:docid:photoshop:95f8e568-92f9-11dc-98e5-f9d39d5d28c7, adobe:docid:photoshop:95f8e568-92f9-11dc-98e5-f9d39d5d28c7, adobe:docid:photoshop:95f8e568-92f9-11dc-98e5-f9d39d5d28c7, adobe:docid:photoshop:998e68d2-fd27-11dc-a002-a50105bab3dd, adobe:docid:photoshop:998e68d2-fd27-11dc-a002-a50105bab3dd, uuid:9f7df3cf-701d-4353-a812-545d0962ed6a, uuid:9f7df3cf-701d-4353-a812-545d0962ed6a, uuid:9f7df3cf-701d-4353-a812-545d0962ed6a, uuid:9f7df3cf-701d-4353-a812-545d0962ed6a, uuid:9f7df3cf-701d-4353-a812-545d0962ed6a, uuid:7a1c4ccd-dba2-4893-8797-38e09bb00b76, uuid:7a1c4ccd-dba2-4893-8797-38e09bb00b76, uuid:5AEA4A2978FBDC11A9009E93566E5E48, uuid:58EA4A2978FBDC11A9009E93566E5E48, uuid:FE8BC8ECEBF9DC1186629816A8BC15F4, uuid:21860057-bd91-41e6-a902-d06280db6c30, uuid:05fbfe70-f41f-4b97-bc02-e0e0c9e5b9d2, uuid:05fbfe70-f41f-4b97-bc02-e0e0c9e5b9d2, uuid:0A420012BEECDC11B501E85215E17004, uuid:7a1c4ccd-dba2-4893-8797-38e09bb00b76, uuid:7a1c4ccd-dba2-4893-8797-38e09bb00b76, uuid:1771eeae-6724-11da-8cd0-000a95784b7c, uuid:7a1c4ccd-dba2-4893-8797-38e09bb00b76, uuid:7a1c4ccd-dba2-4893-8797-38e09bb00b76, uuid:7a1c4ccd-dba2-4893-8797-38e09bb00b76, uuid:7a1c4ccd-dba2-4893-8797-38e09bb00b76, uuid:A0FC15F64028DD11BB21E2BABB8D20E9, uuid:D7F80FAD4428DD11BB21E2BABB8D20E9, uuid:7a1c4ccd-dba2-4893-8797-38e09bb00b76, uuid:7a1c4ccd-dba2-4893-8797-38e09bb00b76, uuid:7a1c4ccd-dba2-4893-8797-38e09bb00b76, uuid:7a1c4ccd-dba2-4893-8797-38e09bb00b76, uuid:7a1c4ccd-dba2-4893-8797-38e09bb00b76, uuid:7a1c4ccd-dba2-4893-8797-38e09bb00b76, uuid:f5c7b439-c641-4ec5-ad56-c90a80573352, adobe:docid:photoshop:f617b51b-9ec9-11dc-a541-f20938be402d, uuid:91755d41-9af5-4c9a-8d10-e0e84116d1c1, adobe:docid:photoshop:8b9370a6-0a28-11dc-a2df-de8e205f211a, uuid:91755d41-9af5-4c9a-8d10-e0e84116d1c1, adobe:docid:photoshop:8aa0b23d-e502-11da-9e33-c7eab616b17a, uuid:f5c7b439-c641-4ec5-ad56-c90a80573352, uuid:b99e6c4e-30b8-44d4-b742-ebe0d2fb97e2, adobe:docid:photoshop:83ed19c2-f53a-11dc-b97a-90185018ca8f, adobe:docid:photoshop:208d9996-dbfc-11dc-9b9a-81a0fb521c58, uuid:d54d53bb-ef8f-4de6-932b-610a409ca3e9, uuid:91755d41-9af5-4c9a-8d10-e0e84116d1c1, adobe:docid:photoshop:ac5a96f4-914f-11dc-ac6d-fd4b8fe4d062, adobe:docid:photoshop:ac5a96f4-914f-11dc-ac6d-fd4b8fe4d062, adobe:docid:photoshop:e64b03ee-92d8-11dc-98e5-f9d39d5d28c7, adobe:docid:photoshop:92f86bb4-d372-11dc-96b0-d239ca376213, adobe:docid:photoshop:1552b081-e01a-11dc-9593-e619b6fdc8c5, adobe:docid:photoshop:8095d847-b632-11db-a9be-f1583d2d1097, adobe:docid:photoshop:9d6ec069-ae63-11dc-a308-a0b8e4b701ed, adobe:docid:photoshop:25a83498-d0fc-11dc-8a27-fb6b64813dba, adobe:docid:photoshop:5710c42a-d0ff-11dc-8a27-fb6b64813dba, adobe:docid:photoshop:82e48ee0-d108-11dc-8a27-fb6b64813dba, adobe:docid:photoshop:516654ac-fabb-11dc-a002-a50105bab3dd, adobe:docid:photoshop:0f1d5034-fa93-11dc-a002-a50105bab3dd, adobe:docid:photoshop:11152318-cf95-11dc-9d7d-b8fedb7d8dc0, uuid:6bc471bf-13fe-4c66-a52c-83004cddab1c, uuid:c4da9026-1efa-4a4c-b61e-7775944ebaec, adobe:docid:photoshop:05ec2aaa-9e11-11dc-a541-f20938be402d, adobe:docid:photoshop:05ec2aaa-9e11-11dc-a541-f20938be402d, adobe:docid:photoshop:95f8e568-92f9-11dc-98e5-f9d39d5d28c7, adobe:docid:photoshop:95f8e568-92f9-11dc-98e5-f9d39d5d28c7, adobe:docid:photoshop:05ec2ab2-9e11-11dc-a541-f20938be402d, adobe:docid:photoshop:05ec2ab2-9e11-11dc-a541-f20938be402d, uuid:0896539c-8363-497e-bf70-d805b4c78cc0, uuid:d65d5df7-6866-4e51-aed2-6e3ef20fbb5e, adobe:docid:photoshop:f7f4a6e6-1df1-11dd-ab3d-b0bd15bc3a09, adobe:docid:photoshop:f7f4a6e6-1df1-11dd-ab3d-b0bd15bc3a09, adobe:docid:photoshop:f7f4a6e6-1df1-11dd-ab3d-b0bd15bc3a09, adobe:docid:photoshop:f7f4a6e6-1df1-11dd-ab3d-b0bd15bc3a09, adobe:docid:photoshop:f7f4a6e6-1df1-11dd-ab3d-b0bd15bc3a09, adobe:docid:photoshop:f7f4a6e6-1df1-11dd-ab3d-b0bd15bc3a09, uuid:0896539c-8363-497e-bf70-d805b4c78cc0, adobe:docid:photoshop:f7f4a6e6-1df1-11dd-ab3d-b0bd15bc3a09, adobe:docid:photoshop:f7f4a6e6-1df1-11dd-ab3d-b0bd15bc3a09, adobe:docid:photoshop:f7f4a6e6-1df1-11dd-ab3d-b0bd15bc3a09, adobe:docid:photoshop:f7f4a6e6-1df1-11dd-ab3d-b0bd15bc3a09, uuid:7a1c4ccd-dba2-4893-8797-38e09bb00b76, adobe:docid:photoshop:91178147-1007-11dd-a8de-c3829ebd7b61, adobe:docid:photoshop:91178147-1007-11dd-a8de-c3829ebd7b61, adobe:docid:photoshop:91178147-1007-11dd-a8de-c3829ebd7b61, adobe:docid:photoshop:91178147-1007-11dd-a8de-c3829ebd7b61, adobe:docid:photoshop:91178147-1007-11dd-a8de-c3829ebd7b61, adobe:docid:photoshop:91178147-1007-11dd-a8de-c3829ebd7b61, adobe:docid:photoshop:91178147-1007-11dd-a8de-c3829ebd7b61, adobe:docid:photoshop:91178147-1007-11dd-a8de-c3829ebd7b61, adobe:docid:photoshop:91178147-1007-11dd-a8de-c3829ebd7b61, uuid:9f7df3cf-701d-4353-a812-545d0962ed6a, uuid:91755d41-9af5-4c9a-8d10-e0e84116d1c1, uuid:91755d41-9af5-4c9a-8d10-e0e84116d1c1, adobe:docid:photoshop:7a6daa0f-fa92-11dc-a002-a50105bab3dd, adobe:docid:photoshop:7a6daa09-fa92-11dc-a002-a50105bab3dd, adobe:docid:photoshop:0f1d502e-fa93-11dc-a002-a50105bab3dd, adobe:docid:photoshop:315b7735-e76c-11db-b160-9e51a5eb555c, adobe:docid:photoshop:9d278630-e76c-11db-b3ce-e6a58ee09365, adobe:docid:photoshop:ae5afed3-059e-11dd-a10c-a8354372e141, adobe:docid:photoshop:ae5afed3-059e-11dd-a10c-a8354372e141, adobe:docid:photoshop:ae5afed9-059e-11dd-a10c-a8354372e141, adobe:docid:photoshop:ae5afed9-059e-11dd-a10c-a8354372e141, adobe:docid:photoshop:60cedd0f-04fb-11dd-a10c-a8354372e141, adobe:docid:photoshop:60cedd0f-04fb-11dd-a10c-a8354372e141, adobe:docid:photoshop:fe4c651e-059e-11dd-a10c-a8354372e141, adobe:docid:photoshop:fe4c651e-059e-11dd-a10c-a8354372e141, uuid:B4B9605E8B05DD1196EC9E9226C5BB61, adobe:docid:photoshop:fa1432bb-05a0-11dd-a10c-a8354372e141, adobe:docid:photoshop:fa1432b5-05a0-11dd-a10c-a8354372e141, adobe:docid:photoshop:fa1432b5-05a0-11dd-a10c-a8354372e141, adobe:docid:photoshop:fa1432b5-05a0-11dd-a10c-a8354372e141, uuid:1771eeae-6724-11da-8cd0-000a95784b7c, uuid:6bbded27-0a07-4093-99b3-0dfc1f75e9cf, uuid:10C8B93ADABE11DBBBA5BF98F8380F6A
Format                          : application/pdf
Producer                        : Adobe PDF Library 8.0
Trapped                         : False
Page Count                      : 49
Creator                         : Adobe InDesign CS3 (5.0.2)

EXIF Metadata provided by EXIF.tools

LT 52246 Lt52246 Manual

Navigation menu

Versions of this User Manual:

Views

Navigation