Noctua NH D15 (EN) Manual En

User Manual:

Open the PDF directly: View PDF .
Page Count: 6

Download
Open PDF In Browser	View PDF

LGA115x

Noctua NH-D15 | Installation Manual | LGA115x

Dear customer,
Congratulations on choosing the Noctua NH-D15. Built on the
basis of the legendary NH-D14 and carrying on its quest for ultimate
quiet cooling performance, our flagship model NH-D15 is an eliteclass dual tower cooler for the highest demands. I’m confident that
you will be able to sense some of the research, attention and care
we’ve put into making this cooler. Enjoy your NH-D15!

Yours sincerely,

Roland Mossig, Noctua CEO

This manual will guide you through the installation process
of the SecuFirm2™ mounting system step by step. Prior to
installing the cooler, please consult the compatibility list on
our website (www.noctua.at/compatibility) and verify that the
cooler is fully compatible with your motherboard. Should you
encounter any difficulties, please check the FAQs on our website
(www.noctua.at/faqs) and don’t hesitate to contact our support
team at support@noctua.at. Noctua cannot be held responsible for any damage or losses caused by compatibility issues.

Place the backplate on the rear side of the mainboard so that the
bolts stick through the mounting holes.

Fix the mounting bars using the 4 thumb screws.

Caution: Please make sure that the three cut-outs in the
supplied backplate align with the screws of the mainboard’s stock
backplate.

Caution: Gently tighten the screws until they stop, but don’t use
excessive force.

Step 4
Step 3

Applying thermal paste

First put the plastic spacers onto the bolts of the backplate, then
add the mounting bars.

If there are residual traces of thermal paste or thermal pads on
your CPU, please clean them off first. Then press a small drop
(4-5mm diameter) of NT-H1 onto the centre of the heatspreader.

Installing the mounting bars

Multilingual versions of this manual are available on our
website: www.noctua.at/manuals
Required mounting parts:

1x NM-IBP2 Backplate

2x NM-IMB2 Mounting Bars

Caution:
Choose the alignment of the mounting bars according to the desired
final orientation of the cooler:
4x NM-IPS1 Spacers

4x NM-ITS1 Thumbscrews

Orientation A

Orientation B

Caution: Applying too much thermal paste will lower heat
conductivity and cooling performance!

Step 1

Removing the mainboard

Step 5

In case you want to use the cooler on an assembled system and
your case doesn’t have a cut-out at the rear side of the mainboard
tray, you first have to remove the mainboard from the case in
order to be able to install the supplied backplate.

Caution: Please first take off the center fan as well as the protection cover at the bottom side of the heatsink.

Step 2

Attaching the backplate

Caution: The supplied backplate will install over the mainboard’s
stock backplate, so the mainboard’s stock backplate must not be
taken off.

Fastening the heatsink to the CPU

Caution: Make sure that the curved sides of the mounting bars are
pointing outwards.

LGA115x
Then put the heatsink onto the CPU and screw it to the screw
threads of the mounting bars.

Noctua NH-D15 | Installation Manual | LGA115x
3.

Use the heatsink with the centre fan only in order to guarantee
best compatibility with tall RAM modules. Add the second fan to
the front fin-stack for further improved cooling performance.
Connect the fan(s) to the mainboard’s CPU fan header(s). If
necessary, use the supplied NA-YC1 y-split cable to connect both
fans to one fan header.
Caution: Tighten the screws until they stop.

Step 6

Fan Setup
Reattach the centre fan and, optionally, install the second fan (in
grey) using the supplied steel clips:

Depending on your CPU and the temperature inside the case,
you may interconnect the supplied NA-RC7 Low-Noise Adaptors
(L.N.A.) in order to further reduce the fans’ operating noise.
Caution: Never use one adaptor for both fans by putting it before
the y-split cable.
Low-Noise Adaptor

Y-Split Cable

1.
Mainboard

Y-Split Cable

Fans

Low-Noise Adaptors

Caution: When using the L.N.A.s, check the temperature of your
CPU using appropriate software (e.g. the respective applications
of your mainboard manufacturer), in order to evade automatic
throttling of the CPU due to the increased temperature. If the
cooling performance is insufficient, please increase case ventilation or remove the L.N.A.s.

Warranty, Support and FAQs
Even with high-grade products and strict quality control, the
possibility of defects cannot be eliminated entirely. Therefore,
we aim at providing the highest possible level of reliability and
convenience by offering a warranty period of 6 years and direct,
fast and straightforward RMA service.
Should you encounter any problems with your NH-D15, please
don’t hesitate to contact our support team (support@noctua.at).
Please also consult the FAQ section on our website:
www.noctua.at/faqs.

LGA2011

Noctua NH-D15 | Installation Manual | LGA2011

Dear customer,

Step 2

Then put the NM-IMB2 mounting-bars onto the bolts.
Congratulations on choosing the Noctua NH-D15.
Built on the basis of the legendary NH-D14 and carrying on its
quest for ultimate quiet cooling performance, our flagship model
NH-D15 is an elite-class dual tower cooler for the highest demands.
I’m confident that you will be able to sense some of the research,
attention and care we’ve put into making this cooler.
Enjoy your NH-D15!

Applying thermal paste
If there are residual traces of thermal paste or thermal pads on
your CPU, please clean them off first. Then press a small drop
(4-5mm diameter) of NT-H1 onto the centre of the heatspreader.

Yours sincerely,
Caution: Choose the alignment of the mounting bars according to
the desired final orientation of the cooler:

Roland Mossig, Noctua CEO

This manual will guide you through the installation process
of the SecuFirm2™ mounting system step by step. Prior to
installing the cooler, please consult the compatibility list on
our website (www.noctua.at/compatibility) and verify that the
cooler is fully compatible with your motherboard. Should you
encounter any difficulties, please check the FAQs on our website
(www.noctua.at/faqs) and don’t hesitate to contact our support
team at support@noctua.at. Noctua cannot be held responsible
for any damage or losses caused by compatibility issues.

Orientation A

Orientation B
Caution: Applying too much thermal paste will lower the heat
conductivity and cooling performance!

Step 3

Fastening the heatsink to the CPU
Caution: Make sure that the curved sides of the mounting bars are
pointing outwards.

Caution: Please first take off the center fan as well as the protection cover at the bottom side of the heatsink.

Multilingual versions of this manual are available on our
website: www.noctua.at/manuals

Required mounting parts:

NM-IBT2 Bolts

NM-IMB2 Mounting Bars

4x NM-ITS1 Thumbscrews

Fix the mounting bars using the 4 thumb screws.

Then put the heatsink onto the CPU and screw it to the screw
threads of the mounting bars.

Step 1

Installing the mounting bars
First screw the NM-IBT2 bolts into the screw threads of the
LGA2011 socket frame.

Caution: Gently tighten the screws until they stop, but don’t use
excessive force.

Caution: Tighten the screws until they stop.

LGA2011

Noctua NH-D15 | Installation Manual | LGA2011

Step 4

Fan Setup
Reattach the centre fan and, optionally, install the second fan
(in grey) using the supplied steel clips:
1.

Caution: Never use one adaptor for both fans by putting it before
the y-split cable.
Low-Noise Adaptor

Mainboard

Y-Split Cable

Fans

Low-Noise Adaptors

Caution: When using the L.N.A.s, check the temperature of your
CPU using appropriate software (e.g. the respective applications
of your mainboard manufacturer), in order to evade automatic
throttling of the CPU due to the increased temperature. If the cooling performance is insufficient, please increase case ventilation or
remove the L.N.A.s.

Please also consult the FAQ section on our website:
www.noctua.at/faqs.

AM2
Dear customer,

Noctua NH-D15 | Installation Manual | AMD
Step 2

Attaching the mounting bars

Congratulations on choosing the Noctua NH-D15.
Built on the basis of the legendary NH-D14 and carrying on
its quest for ultimate quiet cooling performance, our flagship
model NH-D15 is an elite-class dual tower cooler for the highest
demands. I’m confident that you will be able to sense some of the
research, attention and care we’ve put into making this cooler.

First put the plastic spacers onto the screw threads, then fix the
mounting bars using the 4 long screws.

Enjoy your NH-D15!

Yours sincerely,

Roland Mossig, Noctua CEO
Caution: Applying too much thermal paste will lower heat
conductivity and cooling performance!

Step 4

Fastening the heatsink to the CPU
Caution: Make sure that the curved sides of the mounting bars are
pointing inwards.

Caution: Please first take off the center fan as well as the protection cover at the bottom side of the heatsink.

Multilingual versions of this manual are available on our
website: www.noctua.at/manuals
Required mounting parts:

2x NM-AMB1 Mounting Bars

4x NM-ALS1 Screws

4x NM-APS1 Plastic Spacers

Caution: Tighten the screws until they stop.
Then put the heatsink onto the CPU and screw it to the screw
threads of the mounting bars.

Caution: The SecuFirm2™ mounting system requires a backplate, which is preinstalled on most AMD mainboards. If your
mainboard doesn’t have a backplate, please contact our support
team at support@noctua.at.

AMD stock backplate

Step 1

Removing the retention module

Step3

If your mainboard uses a retention module for CPU cooler installation, please remove it first. The SecuFirm2™ mounting system
will install directly to your mainboard’s stock backplate on the rear
side of the socket.

If there are residual traces of thermal paste or thermal pads on
your CPU, please clean them off first. Then press a small drop
(4-5mm diameter) of NT-H1 onto the centre of the heatspreader.

Applying thermal paste

Caution: Tighten the screws until they stop.

AM2

Noctua NH-D15 | Installation Manual | AMD

Step 5

Fan Setup
Reattach the centre fan and, optionally, install the second fan
(in grey) using the supplied steel clips:
1.

Caution: Never use one adaptor for both fans by putting it before
the y-split cable.
Low-Noise Adaptor

Mainboard

Y-Split Cable

Fans

Low-Noise Adaptors

Caution: When using the L.N.A.s, check the temperature of your
CPU using appropriate software (e.g. the respective applications
of your mainboard manufacturer), in order to evade automatic
throttling of the CPU due to the increased temperature. If the cooling performance is insufficient, please increase case ventilation or
remove the L.N.A.s.

Warranty, Support and FAQs
Even with high-grade products and strict quality control, the possibility of defects cannot be eliminated entirely. Therefore, we aim
at providing the highest possible level of reliability and convenience by offering a warranty period of 6 years and direct, fast and
straightforward RMA service.
Should you encounter any problems with your NH-D15, please
don’t hesitate to contact our support team (support@noctua.at).
Please also consult the FAQ section on our website:
www.noctua.at/faqs.

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Instance ID                     : uuid:577368c5-613a-4f9d-b93d-f7bf5c385d2d
Original Document ID            : adobe:docid:indd:7e3471dd-da18-11e0-acad-8cd58205ad45
Document ID                     : xmp.id:A745BA4E80AEE311B3E0A812CBD33842
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:A545BA4E80AEE311B3E0A812CBD33842
Derived From Document ID        : xmp.did:3375054EF619E311AD57E3417C1B32FB
Derived From Original Document ID: adobe:docid:indd:7e3471dd-da18-11e0-acad-8cd58205ad45
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2014:03:18 10:35:35+01:00
Create Date                     : 2014:03:18 10:35:35+01:00
Modify Date                     : 2014:03:18 10:36:24+01:00
Metadata Date                   : 2014:03:18 10:36:24+01:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Format                          : application/pdf
Title                           : Noctua NH-D15 (EN)
Creator                         : 
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Layout                     : SinglePage
Page Count                      : 6
Warning                         : [Minor] Ignored duplicate Info dictionary

EXIF Metadata provided by EXIF.tools

Noctua NH D15 (EN) Manual En

Navigation menu

Versions of this User Manual:

Views

Navigation