P2 16td2p
User Manual: p2-16td2p Productivity2000 User Manual and Inserts
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
Output Specifications 2000 Outputs per Module Voltage Rating Operating Voltage Range Maximum Output Current 16 sourcing 24VDC 21.6-26.4 VDC 0.25 A continuous On Voltage Drop 0.7 VDC Maximum Inrush Current OFF to ON Response ON to OFF Response Overcurrent Trip Self-limited 0.5 ms 0.5 ms 0.6 A min., 1.2 A max. Minimum Load Current to Avoid Open Load Fault Detection 113µA Overtemperature Shutdown Load Resistance to Avoid Open Load Fault Detection Status Indicators External 24V Error Indicator Fault Condition Indicator Commons Fuses External DC Power Required Document Name P2-16TD2P-DS Independent to each output <58kΩ Logic Side (16 points) Logic Side (1 point) Logic Side (16 points) 1 None 24VDC @ 55mA (not including 0.25 A per point) Edition/Revision 1st Ed. Date 3/16/2015 Copyright 2015, AutomationDirect.com Incorporated/All Rights Reserved Worldwide Sales 800-633-0405 P2-16TD2P Sourcing Protected DC Output The P2-16TD2P DC Output Module provides sixteen 24 VDC sourcing outputs with short-circuit and overload protection for use with the Productivity2000 System. Output Specifications................................................ 1 Module Installation.................................................... 2 Wiring Options........................................................... 2 Wiring Diagram and Schematic................................. 3 QR Code................................................................... 3 Hot Swap Information................................................ 3 Warning..................................................................... 4 Removable Terminal Block Specifications............................................................ 4 General Specifications.............................................. 4 LED Status................................................................ 4 Terminal Block sold separately, (see wiring options on page 2). Warranty: Thirty-day money-back guarantee. Two-year limited replacement. (See www.productivity2000.com for details). www.productivity2000.com 1 Module Installation Wiring Options WARNING: Do not apply field power until the following steps are completed. See hot-swapping procedure for exceptions. 1 2 rotate to seated position ZIPLink Connection System Cable + ZIPLink Module = Complete System ZIPLink pre-wired terminal block cables 0.5 m (1.6 ft) cable 1.0 m (3.3 ft) cable 2.0 m (6.6 ft) cable Step One: Align module catch with base slot and rotate module into connector. 1 Align with slot Step Two: Pull top locking tab toward module face. Click indicates lock is engaged. ZIPLink Modules Feed through Locked Terminal Block with pigtail cable 1.0 m (3.3 ft) cable 2.0 m (6.6 ft) cable Step Three: Attach field wiring using the removable terminal block or ZIPLink wiring system. WIRE STRIP LENGTH www.productivity2000.com ZL-RTB20 Unlocked 2 2 ZL-P2-CBL18 ZL-P2-CBL18-1 ZL-P2-CBL18-2 3 4 Screw Terminal Block only Spring Clamp Terminal Block only Tech Support 770-844-4200 ZL-P2-CBL18-1P ZL-P2-CBL18-2P P2-RTB (Quantity 1) P2-RTB-1 (Quantity 1) Wiring Diagram and Schematic Source +24V QR Code INTERNAL MODULE DIGITAL ISOLATION +24VDC L COM 1 3 2 4 3 5 4 6 5 7 6 8 7 9 10 11 12 13 14 15 16 17 18 L L L L L L L L 24V 2 L L L L L L L L 1 24VDC – + Sales 800-633-0405 8 COM 9 10 11 12 13 14 15 16 Use any QR Code reader application to display the module’s product insert. Caution: If possible, remove field power prior to proceeding. If not, then EXTREME care MUST be taken to prevent damage to the module, or even personal injury due to a short circuit from the live terminal block. Important Hot-Swap Information The Productivity2000 supports hot-swap! Individual modules can be taken offline, removed, and replaced while the rest of the system continues controlling your process. Before attempting to use the hot-swap feature, be sure to read the hot-swap topic in the programming software’s help file or our online documentation at AutomationDirect.com for details on how to plan your installation for use of this powerful feature. www.productivity2000.com 3 WARNING: To minimize the risk of potential safety problems, you should follow all applicable local and national codes that regulate the installation and operation of your equipment. These codes vary from area to area and it is your responsibility to determine which codes should be followed, and to verify that the equipment, installation, and operation are in compliance with the latest revision of these codes. Equipment damage or serious injury to personnel can result from the failure to follow all applicable codes and standards. We do not guarantee the products described in this publication are suitable for your particular application, nor do we assume any responsibility for your product design, installation, or operation. If you have any questions concerning the installation or operation of this equipment, or if you need additional information, please call Technical Support at 770-844-4200. This publication is based on information that was available at the time it was printed. At AutomationDirect.com® we constantly strive to improve our products and services, so we reserve the right to make changes to the products and/or publications at any time without notice and without any obligation. This publication may also discuss features that may not be available in certain revisions of the product. Removable Terminal Block Specifications Part Number Number of Positions Wire Range Conductors Screw Driver Width Screw Size Screw Torque 4 P2-RTB P2-RTB-1 18 Screw Terminals 18 Spring Clamp Terminals 30-16 AWG (0.051 - 1.31 mm²) 28-16 AWG (0.081 - 1.31 mm²) Solid / Stranded Conductor Solid / Stranded Conductor 3/64 in. (1.2 mm) Insulation Maximum 3/64 in. (1.2 mm) Insulation Maximum 1/4 in. (6-7 mm) Strip Length 19/64 in. (7-8 mm) Strip Length “USE COPPER CONDUCTORS, 75°C” or Equivalent. 1/8 inch (3.8 mm) Maximum M2 2.5 lb·in (0.28 N·m) www.productivity2000.com N/A N/A General Specifications Operating Temperature Storage Temperature Humidity Environmental Air Vibration Shock Field to Logic Side Isolation Insulation Resistance Heat Dissipation Enclosure Type Module Keying to Backplane 0° to 60°C (32° to 140°F), -20° to 70°C (-4° to 158°F) 5 to 95% (non-condensing) No corrosive gases permitted IEC60068-2-6 (Test Fc) IEC60068-2-27 (Test Ea) 1800VAC applied for 1 second >10MΩ @ 500VDC 2.6W Open Equipment UL508 file E139594, Canada & USA CE (EN61131-2*) Electronic Module Location Any I/O slot in a Productivity2000 System. Agency Approvals Use ZIPLink Wiring System or removable terminal block (not included). See “Wiring Options” on page 2. See the “EU Directive” topic in the EU Directive Productivity2000 Help File. Information can also be obtained at: www.productivity2000.com Connector Type (not included) 18 Position Removable Terminal Block Weight 90g (3.2oz) Field Wiring *Meets EMC and Safety requirements. See the D.O.C. for details. LED Status Fault Condition Fault Status Indication Missing External 24VDC V1 LED is ON Open Load (Note 1) F LED is ON (Note 2) Over Temperature or Over Load Current Operation to Reset Fault Apply external 24 VDC Connect the load Turn the output OFF or cycle power Note 1: O pen Load Fault is always enabled, but is only valid when output is OFF. If Open Load Fault happens while output is ON, fault will not appear until you turn OFF output. Note 2: The SEL button cycles between the output status and fault status. If the “F” LED is OFF the numbered LEDs are showing output status. If the “F” LED is ON the numbered LEDs are showing fault status of each output. The “V1” LED is independent of fault or output display. Tech Support 770-844-4200
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Create Date : 2015:03:16 11:24:19-04:00 Metadata Date : 2015:03:16 11:24:48-04:00 Modify Date : 2015:03:16 11:24:48-04:00 Creator Tool : Adobe InDesign CC (Windows) Instance ID : uuid:82d83ab6-bab8-4345-8acd-fd6bf68cb766 Original Document ID : xmp.did:4CC8A9817BEDE311AD9E8A5FA38FC23B Document ID : xmp.id:f05978bb-235a-254c-887e-bc20e51e8d9e Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:f1d9d565-ee70-634f-8130-e2dfb3298b4d Derived From Document ID : xmp.did:047BBF606CFCE311B967B674276BA900 Derived From Original Document ID: xmp.did:4CC8A9817BEDE311AD9E8A5FA38FC23B Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC (Windows) History Changed : / History When : 2015:03:16 11:24:19-04:00 Format : application/pdf Producer : Adobe PDF Library 11.0 Trapped : False Page Count : 4 Creator : Adobe InDesign CC (Windows)EXIF Metadata provided by EXIF.tools