HT10 Operation Guide Modified With Drawings 12 10 2014 Panelthing_operationguide Panelthing Operationguide

User Manual: panelthing_operationguide

Open the PDF directly: View PDF PDF.
Page Count: 2

DownloadHT10 Operation Guide Modified With Drawings 12-10-2014 Panelthing_operationguide Panelthing Operationguide
Open PDF In BrowserView PDF
Page 1

HT10 Panel Thing - Operation Guide
Use the following procedure to quickly mount hoods, doors, deck lids, lift gates and
tailgates:

Figure 3 Rotate the H56 square bolt ¼
turn to lock on the parts adapter arms
(HD4 or HD5). This step is most
necessary when the arms are pointing
downward.

Figure 1
Step 1: Hold the C2 round tube in the
vertical position.
Step 2: Tighten aluminum clamping
knob to lock C2 in the vertical position. .
Figure 4
Note the indicator hole
showing maximum extension of the D2
horizontal slider.

Figure 2 For small to medium hoods,
doors, lift gates and deck lids, install the
parts HD4 adapter arms pointing
upward as shown. For long hoods and
lift gates, install the HD4 parts adapter
arms horizontal or pointing downward.
For pickup truck tailgates, install the
HD5 arms pointing upward. Use the
arm position that makes your part
balance best for easy rotation

Figure 5 On your body panel, select two
holes about equal distance from center
and near the bottom edge. You can turn
the D3 sliders around to place hooks
near the middle of your part, but try to
keep both lower hooks roughly the same
distance from center.

Page 2

HT10 Panel Thing - Operation Guide

Figure 6

Attaching Body Panels

Steps 1 and 2: Make sure the C2 tube is locked in the vertical position (see Figure 1).
Center the body panel roughly side to side and place it onto the lower hooks.
Step 3: While holding the body panel firmly, move the C2 round slider up or down until the
upper ball handle is slightly above the panel.
Step 4: Tighten the lower T-knob on the C2 slider.
Step 5: Slide the hook on center arm C3 down into a hole near the center of the body
panel. For attachment to doors, you can push the center hook down against the door’s top
inner edge. You may rotate the C3 center arm a few degrees side-to-side to reach offcenter holes.
Step 6: While applying medium down pressure on the C3 center arm, tighten the upper Tknob. As you tighten the upper T-knob, you will see the C3 center arm moving downward.
This downward movement will clamp your part very tightly. If the part feels loose when you
shake the upper ball knob, loosen the upper T-handle three or four turns, pull the center
hook arm down against the panel and retighten the T-handle.
Set rotating friction: Tighten the aluminum clamping knob only enough to hold the panel
still when you are not rotating it.
To remove parts, rotate your body panel to vertical and tighten the main clamping knob
(see Figure 1). While holding the body panel firmly, loosen the upper T-knob and rotate
the C3 center arm out of the way. Along with a helper, lift your panel off the lower hooks.

Copyright 2014 Time Shaver Tools, Inc. Orange, CA
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 2
Title                           : HT10 Operation Guide Modified with drawings 12-10-2014
Author                          : Time Shaver Tools
Subject                         : 
Producer                        : Mac OS X 10.8.5 Quartz PDFContext
Creator                         : Word
Create Date                     : 2014:12:19 16:51:27Z
Modify Date                     : 2014:12:19 16:51:27Z
Apple Keywords                  :
EXIF Metadata provided by EXIF.tools

Navigation menu