Perfect 10 Issa Hybrid Exhibit Kit Vk 1508 Setup Instructions

perfect-10-issa-hybrid-exhibit-kit-vk-1508-setup-instructions

User Manual:

Open the PDF directly: View PDF PDF.
Page Count: 9

www.classicexhibits.com
866.652.2100
© 2014
WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - P10 -
Page 1 of 5
Step 1
patent D599,121
VK-1508 Issa - General Layout
Plan View Perspective View
10’
10’
www.classicexhibits.com
866.652.2100
© 2014
WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - P10 -
Page 1 of 5
Step 1
patent D599,121
Issa - Backwall Assembly
Item
1
2
3
3a
4
5
6
7
8
Qty.
1
1
1
1
2
1
1
1
1
Steps:
NOTE: Assembly may be easiest if assembled face down on floor then lifted upright.
1) Connect upper curved vertical extrusions [3a,3,6] to leg assemblies [1,2,5].
2) Connect lower and upper horizontal extrusions between vertical assemblies by slightly
tightening BLACK knobs on backside of extrusion as shown.
NOTE: Make sure velcro faces toward back and knobs face horizontally as shown in detail.
** Various Accessories Available **
Description
Left Leg Assembly
Middle Leg Assembly
Upper Curved Vertical
Upper Curved Vertical
23”w Horizontal
Right Leg Assembly
Upper Curved Vertical
69”w Horizontal
69”w Horizontal
1
2
5
3a
3
6
4
4
7
8
Start Assembly of Backwall face
down on floor. Then lift upright.
Black
Knob
Horizontal
extrusion
Turn Knob Clockwise
to Tighten Lock
STAR indicates location of
knobs on BACKSIDE of unit.
Stopper Stopper
Stopper
Hinge Extrusion
Vertical
Connection Bar
Vertical Connection Bar -
Slide Bar into lower leg
assembly, secure in place.
Slide upper vertical over
bar and secure into place.
Step stool may be required
for assembly.
NOTE: When assembling horizontals they should be
placed approximately one inch from TOP and BOTTOM.
Slide
horizontal into groove
Assure
that a good
connection is made
and tighten to secure.
www.classicexhibits.com
866.652.2100
© 2014
WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - P10 -
Page 2 of 5
Step 2
patent D599,121
Issa - Blade Attachment
Slide A10 Clamp into groove
of square extrusion.
When desired location is
found, tighten set screw
to secure.
Set-
Screw
A10
Tighten plastic knob
to secure Wing in place.
Knob
Decorative Blade Attachment
(if accidently removed)
Attach decorative wing and
blades to A10’s attached to
Backwall as shown.
Hex Key Tool Flathead
Screwdriver
(if necessary)
www.classicexhibits.com
866.652.2100
© 2014
WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - P10 -
Page 3 of 5
Step 3
patent D599,121
Issa - Backwall Attachments
Shelf attaches to section
5 by setting atop pins
located on right side
and securing into place
with thumbscrew on left.
Cubby Attachment
Slide onto back pin first.
When attaching counter you will need to first
slide shelf onto back pin then set down on front
pin.
Pins
Thumbscrew
9
Shelf attaches to back of
sections 1 and 2 by setting
atop pins located on back
left side.
Light Connection
Attach lights to
backwall where
desired and
tighten in place.
Wings
A10’s
When desired location
is found, tighten
set screw to secure.
Slide connector on back
of A10 clamp into groove
of extrusion.
Example of A10 Clamp Attachment
Tighten knob to secure
shelf/wing in place.
Accessary Attachment
Attach header support to backwall
and then slide header into groove.
Header Header
www.classicexhibits.com
866.652.2100
© 2014
WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - P10 -
Page 4 of 5
Step 4
patent D599,121
Workstation Assembly
Part Number
A
B
C
D
Steps:
1) Connect lower horizontal extrusion [C] between bottom of leg assemblies [A and B] as shown.
2) Insert Laminated infill into grooves of leg assemblies [A and B].
3) Attach extrusion door between leg assemblies [A and B] and on top of laminated infill.
4) Attach upper horizontal extrusion w/ door stopper [D] between leg assemblies [A and B],
and set flush with top of legs [A and B].
Description
Left Leg Assembly
Right Leg Assembly
Horizontal Extrusion
Horiontal Extrusion w/ Door Stopper
Black
Knob
Turn Knob Clockwise
to Tighten Lock
DOOR
Laminated Infill
A (left)
B (right)
C
D (w/ Door Stopper)
Knobs face INSIDE
of workstation
Knobs face INSIDE
of workstation
Knobs face FORWARD
Pins are
located on INSIDE
FRONT vertical
of Leg
Assemblies
NOTE: Make sure the lock is flush with extrusion before tightening. If lock will not fully
engage, gently rock lock and extrusion back and forth while turning knob until lock
fully opens.
Align with bottom of leg assemblies [A and B].
www.classicexhibits.com
866.652.2100
© 2014
WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - P10 -
Page 5 of 5
Step 5
patent D599,121
Workstation Assembly (Cont’d)
Part Number
E
F
Steps:
1) Attach horizontal extrusion [E] between vertical leg assemblies [A and B] as shown below.
2) Insert Laminated infill into grooves of vertical leg assemblies [A and B].
3) Attach upper horizontal extrusion [F] between vertical leg assemblies [A and B] atop infill.
4)
Place internal shelf into assembled pedestal atop pins.
.
5) Set Counter atop assembled pedestal and secure with Velcro straps attached to underside of top.
Description
Horizontal Extrusion
Horizontal Extrusion
E
Laminated
Infill
Knobs facing FORWARD
Place internal shelf into
workstation then
place counter atop
assembled workstation.
Internal
Shelf
F
Knobs face INSIDE
of workstation
www.classicexhibits.com
866.652.2100
© 2014
WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - P10 -
patent D599,121
Case Packing - Case 1 of 3
Horizontal Extrusions 7 & 8
Additional Items:
- Setup Hardware
- Graphic
- (3) Lights
Level 1 Level 2 Level 3 Level 4 Level 5
Leg Assembly
1
Leg Assembly
5
Leg Assembly
2
Blade Wing
Wings
Header
Vertical Connection Bar
Vertical Connection Bar
Vertical Connection Bar
Top View of Each Level
Horizontal Extrusion 4
Horizontal Extrusion 4
A10’s
Attached
A10’s
Attached
Header Support
Wing Attachment
www.classicexhibits.com
866.652.2100
© 2014
WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - P10 -
patent D599,121
Case Packing - Case 2 of 3
Top View
Level 1
Backside
Shelf
Cubby
www.classicexhibits.com
866.652.2100
© 2014
WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - P10 -
patent D599,121
Case Packing - Case 3 of 3
Level 1 Level 3
Top View of Each Level
Counter
Internal
Shelf
Level 2
Inserts
Door
Level 4
Leg Assembly
B
Horiz. Extrusion F
Horiz. Extrusion D
Level 5
Leg Assembly
A
Horiz. Extrusion E
Horiz. Extrusion C

Navigation menu