PiHPSDR Controller Users Guide Pi HPSDR V1.1.3
User Manual:
Open the PDF directly: View PDF
Page Count: 91
- 1. Introduction 5
- 2. Controller connection requirements 6
- 3. Front panel controls 8
- 4. Front Panel Display 9
- 5. Side panel connections 10
- 6. Quick Start Instructions 11
- 7. Discovery Menu 12
- 8. Main Menu 14
- 9. On-Screen Controls and toolbar Buttons 34
- 10. Tuning 56
- 11. TUNE/SWR/FWD Power 56
- 12. Appendix 57
- 13. Reference materials 60
- 14. Steve Wilson KA6S special addition for Fldigi 61
- 15. Supported CAT Commands 69
- 16. Apache Support 74
- 17. Apache Service and Repair 74
- Early prototypes by John Melton G0ORX (circa: 2015) 75
- 1. Introduction
- 2. Controller connection requirements
- Network LAN Connection
- Controller Hardware requirements
- Controller software requirements:
- 3. Front panel controls
- Default assignments of switches and rotary encoders
- Power ON/OFF – switches external 12vdc 2A power to the Controller
- TUN – MOX/TUNE
- S1 – Band
- S2 – Band Stack
- S3 – Mode
- S4 – Filter
- S5 – Noise Blanker
- S6 – AGC
- FN – Function switch to toggle 8 on screen touch buttons such as TUNE or MOX
- E1 – push encoder knob for selection from Encoder Assignment menu of 11 functions
- E2 – push encoder knob for selection from Encoder Assignment menu of 11 functions
- E3 – push encoder knob for selection from Encoder Assignment menu of 11 functions
- E4 – VFO – main tuning knob
- 4. Front Panel Display
- 5. Side panel connections
- 6. Quick Start Instructions
- Hardware Setup
- Software Setup
- 7. Discovery Menu
- Discover Ethernet Connections to RPi
- Pihpsdr program START button
- 8. Main Menu
- Menu → Exit piHPSDR
- E1, E2, E3 Click-Set Assignments
- Menu → Radio
- Menu → Rx
- Note that if one receiver’s audio is set to output to the plughw device the other receiver cannot be connected to the dmix device for that audio output.
- Menu → Rx (continued)
- Menu → TX with USB Input Source
- Menu → TX Transceiver MIC input
- Menu → PA Gain by Band
- Menu → CW
- Weight – sets the dot/dash weighting.
- Menu → ANT
- Menu → DSP
- Menu → OC Open Collector Aux I/O connectors
- Menu → Display
- Menu → Display (continued)
- Menu → XVTR
- Menu → Equalizers
- Menu → Step
- Menu → Meter
- Menu → VOX
- 9. On-Screen Controls and toolbar Buttons
- Touch Direct Frequency Entry
- Toolbar – Function button
- There are eight (8) switches on the pihpsdr Controller. Switches S1 through S6 change function as you push the FN key
- Four Toolbar menus – select with Function button or front panel switch
- Toolbar – MOX
- Toolbar – Band selection
- Toolbar – Bandstack for each VFO selected
- Toolbar – Mode
- Toolbar – Filter
- Toolbar – NOISE
- Toolbar – AGC
- AGC default value is Medium
- Toolbar – Function button
- Toolbar VFO Lock
- Toolbar CTUN – Click Tuning
- Toolbar A>B A<B A<>B
- Toolbar SPLIT
- Toolbar FREQ
- Toolbar MEM
- Toolbar RIT
- RIT – Receiver Incremental Tuning
- Tapping the RIT OFF/ON enables or disables Receiver Incremental Tuning
- Tapping on the RIT+ (plus) or RIT- (minus) button will
- Tapping the RIT OFF or ON toggles the RIT function
- Tapping RIT CL = RIT CLEAR
- Note: RIT offset shown in YELLOW TEXT below VFO-A
- Toolbar → TUNE
- Note: the FWD power and SWR measurements are indicated in the upper right
- AF Gain Slider
- MIC Gain Slider
- PA Drive Slider
- Tune Drive Slider
- AGC Gain Slider
- Receive Attenuation Slider
- Main screen HIDE
- Menu or Toolbar → Meter
- 10. Tuning
- VFO Encoder
- Touch Screen
- Mouse
- 11. TUNE/SWR/FWD Power
- 12. Appendix
- Encoders and Switches
- Encoders and Switches (continued)
- Switch or Encoder
- E1 E2 E3 click set 11 assignments
- GPIO pin Assignments (RaspberryPi)
- 13. Reference materials
- G0ORX Friedrichshaven pdf and video
- 14. Steve Wilson KA6S special addition for Fldigi
- Using PiHPSDR with other applications:
- Mapping a Serial Port to TCP/IP port in Linux
- Example: Set up GRIG to talk to PiHPSDR
- Example: Connect FLDIGI to PiHPSDR
- Also – check the PTT via CAT button in the lower left corner.
- Now Choose Config/Setup/TCPIP
- Setting up rigctld
- Multi-Client Support
- Running applications with the latest version of Hamlib
- KA6S Summary
- 15. Supported CAT Commands
- 6. Quick Start Instructions
- 5. Side panel connections