PP2 Plus Manual Print V5 Voodoo Lab Pedal Power 2 User Pp2plus
Digital Music Corporation Pedal Power 2 Plus User Manual pp2plus_manual Digital Music Corporation - Pedal Power 2 Plus - User Manual
Voodoo Lab Pedal Power 2 Plus User Manual pp2plus_manual Voodoo Lab - Pedal Power 2 Plus - User Manual
Digital Music Corporation Pedal Power 2 Plus User Manual pp2plus_manual Digital Music Corporation - Pedal Power 2 Plus - User Manual
User Manual: Voodoo Lab Pedal Power 2 Plus User Manual Voodoo Lab - Pedal Power 2 Plus - User Manual
Open the PDF directly: View PDF 
.
Page Count: 12
| Download | |
| Open PDF In Browser | View PDF |
PEDAL POWER 2 PLUS ™ User’s Manual Please visit our web site at: www.voodoolab.com Copyright ©1998-2009 by Digital Music Corporation. This publication is protected by copyright and all rights are reserved. No part of it may be reproduced or transmitted by any means or in any form without the express prior consent in writing from Digital Music Corporation. Voodoo Lab and Pedal Power are trademarks of Digital Music Corp. rev 8/20/09 VOODOO LAB PEDAL POWER User’s Manual Introduction The Voodoo Lab Pedal Power is the finest power supply available for pedal effects. The Pedal Power provides eight 9V outputs which will power any type of battery operated effects. Each output is completely isolated, short-circuit protected, highly filtered and regulated. This insures reliable operation, free of hum and noise. The Pedal Power 2 Plus also powers Line6 modeling pedals, Boss Twin pedals, and includes two variable voltage outputs to simulate worn batteries. The U.S. model (120V input) can operate from 50Hz or 60Hz mains to allow use with a step-down transformer in 50Hz countries. Please take the time to read this entire manual before operating your Voodoo Lab Pedal Power. This will eliminate the possibility of damage to your effects from improper usage. You can also visit our web site at www.voodoolab.com for the latest information on this and other products. Unpacking Your Voodoo Lab Pedal Power box should contain the following: Pedal Power 2 Plus system unit Warranty card AC power cord DC Power cables: 5.5x2.1mm right angle barrel connectors (6) 5.5x2.1mm straight barrel connectors (2) 5.5x2.5mm “red” barrel (1) 3.5mm mini plug (1) 9V battery snap (1) Please take a moment to fill out and mail your warranty card. This will register your warranty, make you eligible for technical support, and allow us to notify you with updates and new product information. Don’t worry, we respect your privacy and never sell our mailing list. System Unit Description 1. AC auxiliary. This is a courtesy AC outlet for convenient powering of AC powered effects or a MIDI foot controller. Note the 200 watt maximum rating. Do NOT plug in your amp here! 2. AC power input jack. This is a standard “IEC-type” connector. 3. Power indicator. This LED indicates the Pedal Power system unit is operating. 4. DC output jacks (8). Each output provides 9 volts of isolated, filtered and regulated DC power for your pedal effects. 5. Voltage selector DIP switches. These switches select the output voltage. Switches 1-8 correspond to DC outputs 1-8. Normal 9V operation is with the switch in the NORMAL (OFF) position. NORMAL 6. SAG controls (not shown). Next to output jacks 7 and 8 are controls to vary the voltage from 4V to 9V. About Pedal Boards Before connecting the Pedal Power to your pedals, let’s talk about pedal boards. The best installation is to mount your pedals and power supply to a suitable pedal board. You can use anything from a piece of plywood to a professionally built unit available from any reliable supplier of road cases. Securely mounting your effects and power supply will make it easy to transport without damage and eliminates excessive flexing of cables which will cause their premature failure. Most devices (pedal effects, power supply, tuner, volume pedals, wah, etc.) can be mounted to the pedal board using an industrial adhesive-backed velcro such as 3M dual lock. Audio cables should be as short as possible. You can use off-the-shelf patch cords, or better yet, make your own exactly to length. Once the cables are all neatly routed, finish the job by securing them with nylon cable ties and cable tie mounts. If you constructed the board itself, heavy duty rubber feet and metal handles are useful and will give a professional appearance. Voodoo Lab can supply you with most necessary materials including dual lock, cable, connectors, hardware and many professional wiring accessories. Contact us for current availability and pricing. Connections The Voodoo Lab Pedal Power has eight DC output jacks. These accept barrel type connectors. Notice that each of your DC power cables have a barrel connector on at least one end. The other end has either another identical barrel connector, a 5.5x2.5mm RED barrel, a 3.5mm mini-plug, or a battery snap.. Use the standard black barrel connector cables with Boss, Ibanez, Voodoo Lab, and most common pedals. If you have a pedal from another manufacturer which appears to use the same connector, you must verify that the polarity is “center negative” to prevent damage to the pedal. This is the standard polarity and virtually all pedals are wired this way. Exceptions are the Fulltone ‘69, SoulBender, and Octafuzz pedals and Big Briar Moogerfoogers, which have their power jacks wired for “center positive”. If you have these or other pedals which require reversed polarity, see “More About Cables” below. Boss Twin pedals, like the DD-20, use the standard barrel connector cables from outputs 5 and 6 only. Keep the corresponding switch in the NORMAL position. When using the cables with 3.5mm mini plugs, you must verify that the polarity is “tip positive”. This is the standard polarity for pedals which use the 3.5mm mini plug for power. Line6 modeling pedals (not Tone Core), like the DL4, use the RED 5.5x2.5mm barrel cable from outputs 5 or 6 only. Remember to set the corresponding switch away from NORMAL. If you have a pedal which has no power jack at all, but it runs on a single 9V battery, you can still power it using your Voodoo Lab Pedal Power. Use the cable with the 9V battery snap on one end. This will mate with the battery snap inside your pedal once its battery has been removed. Voltage Selector DIP Switches On the bottom of the Pedal Power is an 8 position DIP switch with switches numbered 1-8. These switches correspond to outputs 1-8 and select the output voltage. Normally, the switches should all be in the NORMAL position for 9 volt operation. Boss Pedals There are two types of Boss pedals. These are identified by the type of power supply specified, either PSA or ACA. Almost all Boss pedals specify the PSA type adapter and operate at 9V like most other pedals. Boss pedals which specify the ACA type adapter operate at a higher voltage. When powering Boss pedals that require ACA adapters you must use outputs 1-4 only and switch the corresponding voltage selector DIP switch away from NORMAL. The Boss Twin pedals, like the DD-20, have a higher current requirement and will operate from outputs 5 and 6 only. Leave the corresponding switch in the NORMAL position. Line6 Modeling Pedals You can power the Line6 modeling pedals (but not POD) using outputs 5 or 6 and setting the corresponding switch away from NORMAL. Remember to use the RED 5.5x2.5mm barrel cable for these pedals. Line6 Tone Core pedals can be powered from any output with its switch in the NORMAL position, using the black 5.5x2.1mm barrel cable. SAG Outputs Outputs 7 and 8 permit you to adjust or SAG the voltage from 9V down to about 4V. To enable this feature you must set the corresponding switch away from NORMAL. This allows you to simulate worn batteries. This is mostly useful for transistor-based fuzz and distortion circuits, as modern opamp designs are minimally affected by variations in supply voltage. It is not recommended for digital pedals. More About Cables The DC power cables supplied with your Voodoo Lab Pedal Power 2 are suitable for most common pedal effects. If you need additional cables they are available directly from Voodoo Lab. If you need cables of a different length, with reversed polarity, or with a special connector, contact us and we can provide them for you. Visit www.voodoolab.com/cables.htm for more information. Operation Using the above information, connect the DC power cables between the Pedal Power outputs and the power jacks on your pedal effects. Now connect the AC power cord from the AC power input jack on the Pedal Power to a suitable AC outlet. The Pedal Power’s red LED power indicator will light, telling you that it’s working properly. Frequently Asked Questions Check out our online forum for the latest tips and tricks: www.voodoolab.com/forum Can I use my U.S. model Pedal Power in a country with 230V mains? No. Pedal Power units purchased in North America should only be powered with 120VAC. Attempting to use 220-240VAC mains directly will cause permanent damage to your Pedal Power! You must use an appropriate stepdown transformer. Why is the LED on my Boss pedal so dim? Check to see if your Boss pedal is supposed to operate with an ACA type adapter. It will say this either on a sticker near the power jack, or on the bottom plate. You need to operate this pedal at a higher voltage by setting the appropriate voltage selector DIP switch on the bottom of the Pedal Power away from NORMAL. See the section above, “Boss Pedals.” Can the Pedal Power fit in a rack? The height of the Pedal Power was intentionally kept to 1-3/4 inches so that it can fit in one rack space. What if my pedal uses reversed polarity (positive ground)? Because the Pedal Power has each of its DC outputs isolated, it doesn’t matter whether your pedals are negative or positive ground. What does matter is that the power jack has the correct polarity. The barrel connectors provided are for center negative and the 3.5mm mini plugs are for tip positive. If your pedal is different from this, contact Voodoo Lab to obtain the correct cable. Doesn’t my pedal need a 300mA power supply? Not if it runs on a standard 9V battery. The adapter available from the pedal’s manufacturer may be able to supply up to 200 or 300mA, but pedal effects which will run on a battery will not draw more than about 65mA. Can I power my pedal which requires 18V (uses two 9V batteries)? Yes. Because the Pedal Power’s outputs are individually isolated, you can wire two of them in series for 18V. Be sure to observe proper polarity. Voodoo Lab can provide you with a custom cable to do this. How can I get additional DC power cables? Contact Voodoo Lab or go to www.voodoolab.com/cables.htm for more information. What if I need a special cable? Voodoo Lab can provide any cable you need. What is a toroidal transformer and why does my Pedal Power have one? Power transformers create a magnetic field that can cause hum and noise in your effects. A toroidal transformer has a specially designed core that greatly reduces this field. The Pedal Power uses this type of transformer so that your pedal board is quiet. Specifications IEC connector 120V 50/60Hz (North America model) 100V 60Hz (Japan model) 230V 50/60Hz (Europe/Australia model) Model and input power are marked on the bottom of unit. Input: Outputs: 5.5x2.1mm barrel connectors center negative Short circuit protected. DIP Switch: NORMAL Output 1-4 (ACA) 5-6 (L6) 7-8 (SAG) DC Voltage 9V 9V 9V Max current 100mA 250mA 100mA DC Voltage 12.3V 14.5V / 12V (unregulated) Adjustable 4V - 9V Max current 60mA 50mA / 200mA+ 100mA DIP Switch: ON Output 1-4 (ACA) 5-6 (L6) 7-8 (SAG) Physical: 6” wide x 3.4” deep x 1.75” tall (152x86x45mm) Weight 2 lbs. (0.9 kg). Special: Toroidal power transformer. Auxiliary AC outlet, 200 watts max. Warranty Voodoo Lab warrants this product against defects that are due to faulty material or workmanship for a period of five years from the date of original retail purchase. This warranty does not include damage to the product resulting from accident or misuse. This warranty is given to the original purchaser only and it is not assignable to any other person. If the product should become defective within the warranty period, Voodoo Lab will repair it or replace it free of charge, provided it is returned freight prepaid to Voodoo Lab with a valid RMA (return material authorization) number. This warranty shall not apply to any goods that have been repaired or altered by anyone other than the manufacturer. There are no warranties which extend beyond the terms described herein. Should you experience any difficulty with this Voodoo Lab product, contact us as described below. If it is determined that the product must be returned to the factory for repair, you will be issued an RMA and given shipping and packaging instructions. How to Reach Us You can reach us by any of the following: Tel: 707 545 0600 Fax: 707 545 9777 Mail: Voodoo Lab 3165 Coffey Lane, Santa Rosa, CA 95403 Email: info@voodoolab.com Forum: www.voodoolab.com/forum
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:56:37 Create Date : 2009:08:24 11:48:25Z Creator Tool : QuarkXPress(R) 7.5 Modify Date : 2009:08:24 11:51:35-07:00 Metadata Date : 2009:08:24 11:51:35-07:00 Producer : QuarkXPress(R) 7.5 Format : application/pdf Title : PP2 Plus Manual-print v5 X Press Private : %%DocumentProcessColors: Cyan Magenta Yellow Black.%%EndComments Document ID : uuid:78ed3d50-3e54-5348-a246-9c9f919b10e5 Instance ID : uuid:0d0f1d74-20c1-594d-abfc-e0850c4ab41d Page Layout : SinglePage Page Mode : UseThumbs Page Count : 12 Creator : QuarkXPress(R) 7.5EXIF Metadata provided by EXIF.tools