Mini 30revised PDF Ruger Mini30

Ruger Mini-30 Ruger Mini-30

User Manual: PDF T E X T F I L E S

Open the PDF directly: View PDF .
Page Count: 46

Download
Open PDF In Browser	View PDF

INSTRUCTION
MANUAL
FOR
BLUED &
STAINLESS
STEEL

CALIBER
7.62 x 39mm

RUGER®
MINI THIRTY RIFLE
AUTOLOADING RIFLE
NOT FOR USE WITH MINI-14 RIFLES (cal. .223)

Use of corrosively primed imported
ammunition can damage or ruin this
rifle. Use only U.S. commercially
manufactured ammunition.

READ THE INSTRUCTIONS AND
WARNINGS IN THIS MANUAL CAREFULLY
BEFORE USING THIS FIREARM
For Product Service on This Model Please Call:
(603) 865-2442 (See p. 34)

STURM, RUGER & Company, Inc.
Southport, Connecticut 06490 U.S.A.
THIS INSTRUCTION MANUAL SHOULD ALWAYS ACCOMPANY THIS FIREARM AND BE TRANSFERRED WITH IT UPON CHANGE OF OWNERSHIP, OR WHEN THE FIREARM IS LOANED OR PRESENTED TO ANOTHER PERSON.

MS3/12-01 R9

State-By-State Warnings
Certain states require by law that their own specified warning
notices in larger-than-normal type be conspicuously included by
the manufacturer, distributor, or retail dealer with firearms sold
in that state. Sturm, Ruger sells its products in compliance with
applicable laws and regulations. Because our products may be
sold in these states, we include the following:

California:

WARNING

ADVERTENCIA
“A los niños los atraen las armas
de fuego y las pueden hacer funcionar. Ellos pueden causarses
lesions graves y la muerte. Evite
que los niños tengan accesso a las
armas de fuego guardándolas
siempre con llave y descargadas
cuando no las esté utilizando. Si
usted tiene un arma de fuego cargada en un lugar en que un niño
tiene acceso a ella y la usa indebidamente, le pueden dar una
multa o enviarlo a la carcel.”

“Children are attracted to and
can operate firearms that can
cause severe injuries or death.
Prevent child access by always
keeping guns locked away and
unloaded when not in use. If you
keep a loaded firearm where a
child obtains and improperly uses
it, you can be fined or sent to
prison.”

Connecticut:
“UNLAWFUL STORAGE OF A LOADED FIREARM MAY
RESULT IN IMPRISONMENT OR FINE.”

Florida:
“IT IS UNLAWFUL, AND PUNISHABLE BY IMPRISONMENT AND FINE, FOR ANY ADULT TO STORE OR
LEAVE A FIREARM IN ANY PLACE WITHIN THE
REACH OR EASY ACCESS OF A MINOR UNDER 18
YEARS OF AGE OR TO KNOWINGLY SELL OR OTHERWISE TRANSFER OWNERSHIP OR POSSESSION OF A
FIREARM TO A MINOR OR A PERSON OF UNSOUND
MIND.”
3

Maine:
“ENDANGERING THE WELFARE OF A CHILD IS A
CRIME. IF YOU LEAVE A FIREARM AND AMMUNITION
WITHIN EASY ACCESS OF A CHILD, YOU MAY BE
SUBJECT TO FINE, IMPRISONMENT OR BOTH. KEEP
FIREARMS AND AMMUNITION SEPARATE. KEEP
FIREARMS AND AMMUNITION LOCKED UP. USE
TRIGGER LOCKS.”

Maryland:
“WARNING: Children can operate firearms which may cause
death or serious injury. It is a crime to store or leave a loaded
firearm in any location where an individual knew or should
have known that an unsupervised minor would gain access to
the firearm. Store your firearm responsibly!”

Massachusetts:
“WARNING FROM THE MASSACHUSETTS ATTORNEY
GENERAL: This handgun is not equipped with a device that
fully blocks use by unauthorized users. More than 200,000
firearms like this one are stolen from their owners every year
in the United States. In addition, there are more than a thousand suicides each year by younger children and teenagers
who get access to firearms. Hundreds more die from accidental discharge. It is likely that many more children sustain serious wounds, or inflict such wounds accidentally on others. In
order to limit the chance of such misuse, it is imperative that
you keep this weapon locked in a secure place and take other
steps necessary to limit the possibility of theft or accident.
Failure to take reasonable preventive steps may result in innocent lives being lost, and in some circumstances may result in
your liability for these deaths.”
“IT IS UNLAWFUL TO STORE OR KEEP A FIREARM,
RIFLE, SHOTGUN OR MACHINE GUN IN ANY PLACE
UNLESS THAT WEAPON IS EQUIPPED WITH A TAMPER-RESISTANT SAFETY DEVICE OR IS STORED OR
KEPT IN A SECURELY LOCKED CONTAINER.”
4

New Jersey:
“IT IS A CRIMINAL OFFENSE TO LEAVE A LOADED
FIREARM WITHIN EASY ACCESS OF A MINOR.”

New York City:
“THE USE OF A LOCKING DEVICE OR SAFETY LOCK IS
ONLY ONE ASPECT OF RESPONSIBLE WEAPONS STORAGE. ALL WEAPONS SHOULD BE STORED UNLOADED
AND LOCKED IN A LOCATION THAT IS BOTH SEPARATE
FROM THEIR AMMUNITION AND INACCESSIBLE TO
CHILDREN AND ANY OTHER UNAUTHORIZED PERSONS.”

North Carolina:
“IT IS UNLAWFUL TO STORE OR LEAVE A FIREARM
THAT CAN BE DISCHARGED IN A MANNER THAT A
REASONABLE PERSON SHOULD KNOW IS ACCESSIBLE
TO A MINOR.”

Texas:
“IT IS UNLAWFUL TO STORE, TRANSPORT, OR ABANDON AN UNSECURED FIREARM IN A PLACE WHERE
CHILDREN ARE LIKELY TO BE AND CAN OBTAIN
ACCESS TO THE FIREARM.”

Wisconsin:
“IF YOU LEAVE A LOADED FIREARM WITHIN THE
REACH OR EASY ACCESS OF A CHILD YOU MAY BE
FINED OR IMPRISONED OR BOTH IF THE CHILD
IMPROPERLY DISCHARGES, POSSESSES, OR EXHIBITS
THE FIREARM.”
* * * * * * * * * * * * * * * * * * * * * *
Please check with your licensed retailer or state police for additional warnings which may be required by local law or regulation. Such regulations change constantly, and local authorities
are in the best position to advise you on such legal matters.
5

WARNING – LOCKING DEVICES

DO NOT INSTALL
INSIDE TRIGGER GUARD

This firearm was originally sold
with a key-operated locking
device. While it can help provide
secure storage for your unloaded
firearm, any locking device can
fail. All guns are designed to fire
if they are loaded and the trigger
is pulled. Therefore, never install
the locking device inside the trigger guard or in any way that it
can possibly pull the trigger! Do
not leave the keys in the lock.
The ultimate responsibility for
secure storage of any firearm
must depend upon its owner and
his or her individual circumstances. Guns should be securely
stored unloaded, in a secure
location, separate from their
ammunition.
See “Storage Warning”, page 30.

NEVER INSTALL
LOCKING DEVICE
INSIDE TRIGGER GUARD

INSTALL LOCK
AS SHOWN HERE

FIREARMS SAFETY-YOUR RESPONSIBILITY
SAFETY MUST BE THE FIRST AND CONSTANT
CONSIDERATION OF EVERY PERSON WHO
HANDLES FIREARMS AND AMMUNITION.
This Instruction Manual is designed to assist you in learning how to use and care
for your RUGER® MINI THIRTY RIFLE properly. Please contact us if
you have any questions about it.
Only when you are certain you fully understand the Manual and can properly
carry out its instructions should you practice loading, etc. with live ammunition.
If you have any doubts about your ability to handle or use a particular type of
gun safely, then you should seek supervised instruction. Such personalized
instruction is often available from gun dealers, gun clubs or police departments.
If none of these sources can help you, write to the National Rifle Association,
11250 Waples Mill Road, Fairfax, VA 22030-7400. They will assist you.
The person possessing a gun has a full-time job. You cannot guess; you cannot
forget. You must know how to use your firearm safely. Do not use any firearm
without having a complete understanding of its particular characteristics and
safe use.
Remember: There is no such thing as a foolproof gun.

TABLE OF CONTENTS

Page
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Operation of Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
The Bolt Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Ammunition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Magazines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
To Load and Fire (With Magazine) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
To Load and Fire (Without Magazine) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
To Unload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
To Reload the Rifle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
To Extract and Eject a Chambered Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
To Remove a Bore Obstruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
To Clear a Malfunction (“Jam”) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
To Minimize Malfunctions (“Jams”) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Reassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Removal and Replacement of Fiberglass Handguard . . . . . . . . . . . . . . . . . . . . . .27
Magazine Inspection and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Care and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Maintenance of Stainless Steel Rifles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Attaching Ruger Scope Rings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Sight Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Service and Parts Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Parts Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
The Basic Rules of Safe Firearms Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

“RUGER” is a registered U.S. trademark.

WARNINGS OF GREAT IMPORTANCE ARE
FOUND ON THE FOLLOWING PAGES:
Locking Devices
Alterations
Manual Safety
Ammunition
Lead Exposure
Firing
Handling
Sustained Firing

6
8
9
11
12
14
15
16

Unloading
Bore Obstructions
Malfunctions
Disassembly
Lubrication
Storage
Parts Purchasers

16
19
22
23
29
30
35

OTHER CAUTIONS AND WARNINGS APPEAR
THROUGHOUT THE MANUAL.
FIREARMS ARE DANGEROUS WEAPONS–
READ THE INSTRUCTIONS AND WARNINGS
IN THIS MANUAL THOROUGHLY AND
CAREFULLY BEFORE USING.

WARNING–ALTERATIONS
This product was designed to function
properly in its original condition.
Alterations can make it unsafe. Do not
alter any part or add or substitute
parts or accessories not made by
Sturm, Ruger & Co. Inc.

DO NOT ALTER ANY GUN

GENERAL INFORMATION
AND MECHANICAL CHARACTERISTICS
The RUGER® MINI THIRTY RIFLE is a gas operated, box magazine fed,
autoloading rifle. It is simple, reliable, and consists of a relatively few rugged
components. The mechanism employs the Ruger fixed piston/moving cylinder
gas system in conjunction with a simplified Garand-type rotating bolt. The
Mini Thirty Rifle can be field stripped for cleaning to its basic subassemblies in
seconds without the use of tools. The Ruger Mini Thirty is similar, but not identical, to the Ruger Mini-14 series of rifles, and is adapted to an excellent deer
hunting cartridge, the 7.62 x 39mm.
Music wire coil springs are used throughout the mechanism. The safety, located
in front of the trigger guard, blocks both the hammer and sear and permits the
slide to be cycled with the safety “ON”. A bolt lock mechanism is provided for
convenience in holding the bolt open for loading and inspection. The firing pin is
retracted mechanically as the bolt starts to unlock and the rifle will fire only
when the bolt is locked. The one-piece American hardwood stock is reinforced
with steel liners in stressed and high temperature areas. The handguard and forearm are separated from the barrel by an air space to promote cooling.

The Mini Thirty Rifle incorporates a unique patented buffer system which redirects and effectively absorbs the shock of the slide block striking the receiver
in recoil. The bolt stop fits in a slot in the side of the bolt, and it also serves as
the ejector so that the empty cartridges are ejected from the receiver straight out
to the side in order to clear the lowest mounted scope.
The patented Ruger integral scope mounts take all standard Ruger scope rings of
various heights. A blade front sight is used, with a tip-up type folding rear peep
sight, adjustable for windage and elevation.

NOMENCLATURE
HANDGUARD

SCOPE MOUNT BASES
REAR SIGHT

BOLT LOCK
PLUNGER

EXTRACTOR

RECEIVER

SLIDE HANDLE

MAGAZINE LATCH

TRIGGER

SAFETY SHOWN “ON”

Figure 1. In this illustration the frequently used operating components are identified. Note
that the safety is rearward in the trigger guard and is therefore in its “ON” (safe) position.

WARNING – MANUAL SAFETY

Safety in "ON" Position

Keep the safety on unless actually firing.
Always move the safety fully to its intended
position and check it. The safety is not “ON”
unless it is completely “ON”. Never depend on
a safety mechanism or any other mechanical
device to justify careless handling or permitting the rifle to point in an unsafe direction.
The only “safe” rifle is one in which the bolt is
open, the chamber is empty, and there is no
magazine in the gun.

KNOW HOW TO USE THE SAFETY
9

OPERATION OF SAFETY
The manual safety mechanism is located forward of the trigger for convenient
operation and is “ON” when in its fully rearward position intruding into the trigger guard. (See Fig. 2) The safety can be moved to “ON” (extreme rearward position) only when the hammer is cocked. When the safety is “ON”, it blocks both
the hammer and sear. The safety should always be placed “ON” before loading or
unloading the rifle and should be kept “ON” at all times except when actually firing.

SAFETY “OFF”

SAFETY “ON”

(Ready to Fire)

Figure 2.

THE BOLT LOCK
The Mini Thirty Rifle is designed so that the bolt remains open after the last shot
has been fired, provided there is a magazine in the rifle. When the magazine is
empty, the magazine follower actuates the bolt lock which is designed to retain
the bolt and slide in their rearward position.
WARNING: The bolt lock is not a safety device. It should not be used to hold the
bolt back when there are cartridges in the magazine. A slight jar to the butt end
of the rifle will cause the bolt lock to disengage and to feed a cartridge into the
chamber.
The bolt lock should be relied on only to hold the bolt in its rearward position
when the chamber is empty and an empty magazine is in place. The only purpose
of the bolt lock is for convenience in the rapid changing of magazines and for
holding the bolt in its rearward position when the rifle is unloaded for the purpose of cleaning or inspection.

OPERATION OF BOLT LOCK
To manually engage the bolt lock to keep
the bolt open: (See Figure 3)

1. Pull the slide handle all the way to
the rear.
2. Depress the bolt lock plunger and
allow the slide to move forward
until it stops.
3. Put safety “ON” (push fully rearward).

Figure 3

To release the slide (which allows the
bolt to go forward) keep safety “ON” and
either:

Closing The Bolt
3

Remove the magazine, draw the
slide handle to the rear and
release, or;

With an empty magazine in place,
draw the slide handle fully to the
rear and hold it there. Then, while
holding the slide handle, depress
the magazine follower slightly with Figure 4
the thumb, remove the thumb, and
then allow the slide to go forward. (See Figure 4)

Safety
"ON"

CAUTION: Slide is under heavy spring tension and can injure fingers when it
slams shut.

AMMUNITION
The RUGER MINI THIRTY RIFLES are chambered for the 7.62 x 39mm
cartridge, and can use either standard U.S. military or factory loaded sporting
7.62 x 39mm cartridges manufactured in accordance with U.S. industry practice.
Do not attempt to use any other cartridges in this rifle, even though “7.62mm”
may appear in their names (i.e., 7.62 x 51mm NATO [.308 Winchester]; 7.62
Tokarev; 7.62 x 54 Rimmed Russian, etc.). The only correct ammunition for the
Ruger Mini Thirty is the 7.62 x 39mm. The use of corrosively primed ammunition
is not recommended, See “Ammunition Notice” & “Ammunition Warning”, below.
®

WARNING – AMMUNITION
Death, serious injury, and damage
can result from the use of wrong
ammunition, bore obstructions,
powder overloads, or incorrect cartridge components. Even the
strongest gun can be “blown up” as
a result of excess pressure. Always
wear shooting glasses and hearing
protectors.

IMPROPER AMMUNITION
DESTROYS GUNS

AMMUNITION (CARTRIDGES) NOTICE
WE SPECIFICALLY DISCLAIM RESPONSIBILITY FOR ANY DAMAGE OR
INJURY WHATSOEVER OCCURRING IN CONNECTION WITH, OR AS THE
RESULT OF, THE USE IN RUGER FIREARMS OF FAULTY, OR NON-STANDARD, OR “REMANUFACTURED” OR HAND LOADED (RELOADED) AMMUNITION, OR OF CARTRIDGES OTHER THAN THOSE FOR WHICH THE
FIREARM WAS ORIGINALLY CHAMBERED.

USE ONLY FACTORY AMMUNITION LOADED
TO U.S. INDUSTRY STANDARDS

WARNING – LEAD EXPOSURE
Discharging firearms in poorly ventilated
areas, cleaning firearms, or handling
ammunition may result in exposure to
lead and other substances known to the
state of California to cause birth defects,
reproductive harm, and other serious
physical injury. Have adequate ventilation
at all times. Wash hands thoroughly after
exposure.

SHOOTING OR CLEANING GUNS
MAY EXPOSE YOU TO LEAD

MAGAZINES
RUGER® MINI THIRTY magazines are identified by having only one vertical crease in the side of the magazine versus three vertical creases in the Ruger
Mini-14 magazine. The bottom of the Mini Thirty magazine is more tapered than
the generally rectangular bottom of the Mini-14 magazine, and the follower, visible from the top of the magazine, is distinctly more pointed on the Mini Thirty
(see illustrations below). DO NOT ATTEMPT TO USE MINI-14 MAGAZINES IN
RUGER MINI THIRTY RIFLES.
Ruger Mini Thirty Magazine
(Correct)

Ruger Mini-14 Magazine
(Incorrect)

For Caliber 7.62 x 39mm
Ammunition Only

For Caliber .223
Ammunition Only
Do not use in Mini Thirty

Bottom

Top

Side

Bottom

Top

Side

Never attempt to use caliber .223 ammunition in Ruger Mini Thirty rifles, as it
will not chamber correctly and will “jam” the action.These smaller cases will
split upon firing in the larger Mini Thirty chamber, resulting in the release of
hot powder gases into the action and possible personal injury or damage to the
rifle. As with any firearm, always wear safety shooting glasses and adequate hearing protection.

LOADING THE MAGAZINE
Use only clean ammunition of the proper caliber manufactured to U. S. Industry
specifications, in good condition. (See Notice and Warnings in other sections of
this manual pertaining to Ammunition).
To load the magazine, align each cartridge with the bullet forward (pointing
toward the hole in the front of the magazine body) and push downward until the
cartridge snaps into place. Do not attempt to load more than the designated
number of cartridges for which the magazine has been designed. RUGER®
MINI THIRTY RIFLES are sold with 5 round Ruger magazines.
The RUGER® MINI THIRTY magazine is not interchangeable with the
Ruger Mini-14 magazines. Do not use non-Ruger magazines -- they may cause
malfunctions.

DAMAGED, NON-STANDARD, OR IMPROPERLY
ASSEMBLED MAGAZINES SHOULD NOT BE USED.
THEY CAN CAUSE THE RIFLE TO MALFUNCTION.

INSERTING THE MAGAZINE
See Figure 5. The magazine may be inserted with the bolt either in the closed or
open position (See “Bolt Lock” section p. 10).
1. Hold the magazine at an angle as
shown and insert all the way up
into the magazine well. NOTE:
There is a hole in the top-front
portion of the magazine that
mates with a stud on the inside of
the receiver.

2. Pull the bottom of the magazine
toward the trigger guard until the
magazine latch at the rear of the
magazine well engages. Check to
be sure that the magazine is
securely latched into place.

Figure 5

REMOVING THE MAGAZINE
To remove the magazine, simply push the magazine latch forward until the rear
end of the magazine drops out of the magazine well. The magazine can then be
withdrawn from the rifle. To minimize the possibility of damage and malfunctions, do not let the magazine drop to the ground (See Figure 6, p. 23).

TO LOAD AND FIRE (WITH MAGAZINE)
Practice this important aspect of gun handling (with an unloaded rifle) until you
can perform each of the steps - described below - with skill and confidence. But
before you do anything with the rifle, please first read completely through this
manual. This procedure begins with an empty rifle with its magazine out.
1. Be certain the muzzle is pointing in a safe direction. (See Rule 2, p. 42).
2. Before inserting loaded magazine, engage the bolt lock so the bolt is held
open. Check the chamber to be certain it is empty. MOVE THE SAFETY TO
THE “ON” POSITION. (See Figure 3, p. 10).
3. Load a magazine with the desired number of cartridges.
4. Insert the loaded magazine into the magazine well, and immediately...
5. Draw the slide handle all the way to the rear and release it, allowing the slide
to snap forward under full spring force. A cartridge will be stripped from the
magazine and chambered by the motion of the bolt.
WARNING: If cartridges do not feed smoothly from the magazine into the
chamber then do not use the rifle until the problem is corrected. (See
“Malfunction Warning” p. 22)
6. The rifle is now cocked and a loaded cartridge is chambered. Visually check to
be certain the safety is in the “ON” position.
7. When you are ready to fire the rifle, move the safety to the “OFF” position.
WARNING: DO NOT TOUCH THE TRIGGER UNTIL YOU ARE ACTUALLY
READY TO FIRE. KEEP THE SAFETY “ON” UNLESS ACTUALLY FIRING.
8. The rifle will fire one shot each time the trigger is pulled until the magazine is
empty. Some of the gas produced by the combustion of the powder is used to
push the slide and bolt to the rear, which extracts and ejects the fired cartridge
case, recocks the gun, and reloads a new cartridge from the magazine into the
firing chamber.

WARNING – FIRING
The bolt automatically opens
and shuts quickly while firing.
Keep face and hands away from
it. Hot brass and powder gas is
ejected quickly and can burn
you. The rifle should be fired
from the right shoulder.
Always wear shooting glasses
and hearing protectors.

BOLT OPENS FAST–
HOT BRASS EJECTED
14

9. Immediately following the firing of a shot, and if a subsequent shot is not to
be fired at once, put the safety “ON” while the rifle is still pointing in a safe
direction down range. The safety should be moved to the “ON” position as
soon as firing is completed, and it should be “ON” at all times except when
the rifle is on target and being fired.
10. When the last cartridge in the magazine has been fired, the bolt lock will
automatically engage and hold the bolt and slide in the rearward, open position. CAUTION: Autoloading firearms have reciprocating bolts and slides. Do
not position your fingers or face so these components can strike you when
the gun is fired.

WARNING – HANDLING
If dropped or
struck with the
safety “off”, the
rifle may fire.
Keep chamber
empty unless
actually firing!
Keep safety “on”
unless actually
firing!

SAFETY IN "OFF" (FIRE)
POSITION

ANY GUN
MAY FIRE IF
DROPPED

WARNING – SUSTAINED FIRING
The Mini Thirty rifle fires from a
closed bolt. Sustained firing can
create excessive heat in the barrel
and can cause “cook-off” of
ammunition (heat-firing of the
cartridge in the chamber). This
“cook-off” can occur a substantial
period of time after firing has
ceased. Always unload the firearm
immediately after you have finished shooting.

HOT BARREL CAN
“COOK-OFF” (FIRE) CARTRIDGE IN CHAMBER

TO LOAD AND FIRE (WITHOUT MAGAZINE)
The rifle can be used as a single shot rifle in the absence of a magazine or for
safety or training purposes. To do so, follow step 1, p. 14. Then, manually load a
cartridge into the chamber, and follow steps 5 and 6 p. 14, disregarding the magazine. Note that the bolt will not automatically lock open after the cartridge is
fired and automatically ejected. Engage the safety between shots.

WARNING – UNLOADING
So that the rifle can be used as a single loader, it
will fire whether or not a magazine is in the gun
if a cartridge is chambered. Removing magazine
does not unload rifle! To unload, first remove
magazine, then pull bolt to rear, eject chambered
cartridge, and visually inspect chamber. The safety should always be in the “on” (safe) position
when loading or unloading the rifle.

GUN WILL FIRE WITH
MAGAZINE OUT

TO UNLOAD
WARNING: This sequence must be followed exactly as spelled out. Failure to do
so can result in the rifle’s chamber becoming unintentionally loaded with a cartridge!
1. Keep the muzzle pointed in a safe direction at all times and keep the fingers
outside the trigger guard. Move the safety to the “ON” position.

2. Remove the magazine. REMEMBER that even though the magazine has been
removed, a cartridge remaining in the chamber can still be fired!
3. Pull the slide handle all the way to the rear, extracting and ejecting the cartridge in the chamber. When the bolt is fully retracted, push down on the bolt
lock plunger and then allow the slide to move forward until it comes to rest
against the bolt stop.
4. Always visually double check the chamber to be certain it is empty.
5. The only “safe” rifle is one in which the bolt is open and the chamber and
magazine are empty.

CORRECT UNLOADING SEQUENCE

2
1

Safety
"ON"

TO RELOAD THE RIFLE
1. Firing all cartridges in the magazine and the chamber will cause the bolt to
automatically lock open. Keep the rifle pointed in a safe direction. Put the
safety “ON”. Reloading can be accomplished by pressing forward on the magazine latch with the thumb or forefinger. The magazine will fall free of the rifle
of its own weight. To avoid the possibility of damage to the magazine, do not
let it fall to the ground unless rapid reloading is absolutely necessary.
2. Insert a loaded magazine. WARNING: The bolt stop is held in place by a spring
detent. Therefore, when there is a loaded magazine in place and the rifle is
jarred, the bolt can fly forward and chamber a cartridge.
3. Release the bolt to move forward by pulling the slide handle fully to the rear
and release the slide. A cartridge will be chambered when the bolt shuts.
WARNING: The rifle is ready for instant use once the bolt moves forward. If
the rifle is not to be fired immediately, keep the safety “ON”. When you are
ready to fire immediately, take the safety “OFF” and resume firing, putting the
safety back “ON” whenever you cease firing, even for a moment.

TO EXTRACT AND
EJECT A CHAMBERED CARTRIDGE
When the rifle is fired, the same gas pressure that drives the bullet forward acts
through the gas port to push the slide and bolt to the rear. This action causes
extraction and ejection of the fired cartridge case. If a cartridge fails to fire or if
the shooter wishes to eject the chambered cartridge manually, follow the procedure “To Unload” step 3, p. 17. When the slide handle is operated there can be a
failure to extract the cartridge from the chamber, or a failure to eject the cartridge clear of the rifle. These failures usually are the result of the slide handle
not being pulled rearward vigorously. From the foregoing, it is clear that the gun
user must:
1. Always visually check the chamber and the breech-face after opening the slide
to eject a chambered cartridge. If the slide is not vigorously retracted, the
extracted cartridge can be “ejected” into the magazine area or remain held to
the breech-face by the extractor.
2. Thoroughly clean the chamber and the extractor as often as necessary.
If an empty magazine is in the rifle when the slide handle is being retracted to
extract a cartridge, the cartridge may drop on top of the magazine or remain
held to the breech-face by the extractor. Then, when the slide goes forward, the
cartridge will be chambered again! REMEMBER -- always remove the magazine
before clearing the chamber, and visually check to ensure that no cartridges
remain in the gun.

TO REMOVE A BORE OBSTRUCTION
Rifles like the Mini Thirty Rifle are susceptible to damage from firing when the
bore is obstructed. Excess oil, grease, water, or raindrops may form an obstruction which could cause damage and injury. If you suspect that your rifle may
have excess oil, grease or cosmoline in the barrel, or if it may have been

exposed to humid conditions which could cause condensation, or to rain or snow
which might have entered the bore, open the bolt and clean out the barrel. Inspect
the bore visually to be sure that it is perfectly clear (See “Ammunition Warning”,
p. 11 and “Care and Cleaning” section p. 29)

WARNING –BORE OBSTRUCTIONS
Before loading or shooting the Mini Thirty rifle,
be certain the bore is unobstructed. Firing the
rifle with any obstruction in the bore may result
in severe damage to the rifle and serious injury to
the shooter and other persons nearby.
A MISFIRE or unusual report (sound) upon firing
is always a signal to cease firing immediately and
after waiting for one minute, examine the chamber and bore of the firearm. It is not sufficient to
retract the slide handle and examine the chamber.
You must remove the magazine, clear the chamber, lock the bolt open and inspect the bore visually - and with a rod if necessary - to be certain it is
completely clear of any obstruction. Failure to
detect and correctly remove a bore obstruction
can result in serious injury to the shooter and
bystanders, and damage to the firearm.

DO NOT “SHOOT OUT”
A BORE OBSTRUCTION
A gun user should recognize that a lodged bullet is a fairly common form of bore
obstruction. Therefore the following information on how a bullet may become
lodged in the bore, and how it should be removed, deserves most careful reading
and heeding!
1. When firing, a bullet may become lodged in the bore if the cartridge contains
no powder, or the powder fails to ignite and only the primer charge ignites,
producing insufficient force to propel the bullet out of the bore.
2. A bullet may also become lodged in the bore when extracting a cartridge from
the chamber (unloading). If the bullet is not crimped tightly enough in the
cartridge case, the bullet may stick in the bore, with only the case being
extracted.
Experience indicates that the two conditions described above occur most frequently with reloaded ammunition.
When either of the above described (1 or 2) situations occurs, proceed as follows
with the rifle pointing in a safe direction:
a) If the rifle is cocked, move the safety to the “ON” position.
b) Remove the magazine from the rifle.

c) Retract the slide handle and lock it in the open position by pressing in the
bolt lock plunger in the top of the receiver. Retracting the slide handle
should remove the cartridge case. Be certain the safety is in the “ON” position.
d) Check the chamber to be certain there is no cartridge case in it -- if there
is, extract it before proceeding with steps (e) and (f).
e) After making sure that the rifle is unloaded, inspect the bore from the
muzzle end of the barrel. If the bore is obstructed, insert a proper size
cleaning rod (without a tip or brush) into the bore from the muzzle and
dislodge and remove the bullet. If the bullet does not readily dislodge, it
may be necessary to lightly tap the handle end of the cleaning rod. If such
efforts fail to dislodge the bullet, take the rifle to a gunsmith. DO NOT
ATTEMPT TO REMOVE A LODGED BULLET USING A BLANK CARTRIDGE, OR A CARTRIDGE FROM WHICH THE BULLET HAS BEEN
REMOVED, OR BY ANY MEANS OTHER THAN THE USE OF THE PROPER SIZE CLEANING ROD AND REASONABLE FORCE APPLIED TO THE
ROD. BE CERTAIN ALL LOOSE POWDER HAS BEEN REMOVED FROM
THE BORE AND ACTION BEFORE INTRODUCING THE ROD INTO THE
BORE. NEVER TRY TO SHOOT OUT A BORE OBSTRUCTION! See “Bore
Obstruction Warning”, p. 19.
f) Reinspect the bore to be certain it is free of unburned powder particles or
any other debris. At the same time clean the magazine, the magazine well,
and other areas of the mechanism of unburned powder grains.
It is absolutely essential that steps (a) through (f) be followed if there is any
suspicion that a bullet has been lodged in the bore because of the situations
described in 1 or 2 above. Remember that a bullet can be lodged in the bore
of a rifle just where the rifling begins, and a live cartridge can still be chambered and the bolt closed and locked. This can occur because the bullet in the
chambered cartridge is pushed back into the cartridge case far enough to give
the shooter the impression that the loaded cartridge has chambered normally.
Always check the bore for an obstruction if you experience difficulty in chambering a cartridge, experience a failure to extract, have a misfire, or the rifle does
not make a normal loud report on firing.
RELOADERS SHOULD USE ONLY CANNELURED BULLETS AND BE SURE TO
CRIMP THEM SECURELY IN THE CARTRIDGE CASE. NOTE: Sturm, Ruger &
Co. specifically does not recommend the use of reloaded, hand-loaded or remanufactured cartridges. Please see “Ammunition Notice” p. 11.

TO CLEAR A MALFUNCTION (“JAM”)
Before “doing something”, study the situation to determine the nature of the
jam and how best to clear it. Any autoloading firearm may occasionally malfunction. If it does:
1. Be certain the muzzle is pointed in a safe direction and the safety is “ON”.
Keep fingers away from trigger.

2. When attempting to free a jammed cartridge, do not use any type of tool that
is likely to act as a “firing pin” and discharge the cartridge should the tool
impact on the primer. Never use a cartridge as a “tool”.
3. After clearing a jam, inspect the gun mechanism to determine if dirt or debris
might be the cause of the problem. Excess lubricant or grease can cause cartridges to feed sluggishly. An accumulation of grease, dirt or powder grains in
the magazine can contribute to cartridge feeding problems.
4. After clearing a jam, inspect all cartridges that have been removed from the
gun. Safely dispose of any cartridges which are dented or nicked or have bullets that are loose or improperly positioned in the cartridge case.
5. If it appears that the gun and magazine are not at fault and that the jam was
caused by the type of cartridge being used, then try another type.
6. If the above procedures do not result in a smooth and reliable feeding firearm,
don’t use the gun until it feeds cartridges smoothly and reliably. The rifle
should be returned directly to our Newport Product Service Department for
repair. See the “Service and Parts” section p. 34, for packing and shipping
information.
Another precaution: Form the habit of examining fired cartridge cases from time
to time. If fired cases have bulged heads or show splits on any part of the case,
stop using that ammunition and return the rifle to the factory for inspection.
(See page 34)
7. If a cartridge or shell is caught between the bolt and receiver, put the safety
“ON”, retract the slide, and lock it in the open position. Remove the magazine;
then remove the jammed case.
8. If a fired case is in the chamber, use a cleaning rod to knock it out.
9. If an unfired cartridge is stuck in the chamber, remove it from the breech-end
rather than trying to dislodge it with a cleaning rod inserted from the muzzle.
Use a piece of 3/16” brass rod which has one end shaped like a screwdriver tip.
Insert the tip in the extractor groove of the cartridge, use the face of the
receiver ring as a fulcrum and carefully pry out the cartridge. Be careful not to
strike the primer area of the live cartridge! Vigorously brush-clean the chamber with solvent after clearing any jam involving the chamber.

TO MINIMIZE MALFUNCTIONS (“JAMS”)
Autoloading firearms of all makes and types occasionally malfunction when a
cartridge fails to feed from the magazine to the chamber, or when a cartridge (or
fired case) fails to properly extract and eject.
To minimize the possibility of such occurrences the gun user should:
1. Use ammunition of the correct caliber and type which is loaded to Industry
Specifications. Avoid reloads, remanufactured cartridges, and cartridges that
are dirty, corroded, or deformed. (See “Ammunition Warning”, p. 11)
2. Clean and lubricate the gun in accordance with the instructions in this manual.

3. If the mechanism shows signs of not functioning correctly, or if a part is damaged or broken -- don’t use the gun. Have it inspected, and repaired. (See
“Malfunction Warning” below)
4. Use only genuine Ruger® Mini Thirty magazines and carefully load the magazine. Do not exceed the stated magazine capacity. (See “Loading Magazine”, p.
13)
5. Do not ‘ride’ the slide handle when chambering a cartridge from the magazine. The slide should be drawn fully to the rear and then be permitted to snap
forward under the full force of the recoil spring. If a cartridge does not fully
chamber, do not ‘pound’ on the slide handle to force the bolt closed. Rather,
retract the slide, eject the cartridge and determine the cause of the problem.
(See “Bore Obstructions Warning” p. 19)
6. To minimize the probability of an unfired cartridge being jammed should it
‘fall back’ onto the magazine, remove the magazine before retracting the slide.
When extracting an unfired cartridge, tip the right side of the rifle towards the
ground so that gravity will assist the cartridge to fall clear of the magazine
well. Always retract the slide briskly whenever extracting a live cartridge. Take
care to see that a cartridge is not forcibly ejected against a surface where the
primer might be set off.
Alterations to the rifle or use of non-Ruger magazines and accessories may cause
malfunctions. See “Alteration Warning” on page 8. If the above procedures do
not result in a smooth and reliably functioning firearm, don’t use the gun. The
rifle can be returned directly to our Newport, New Hampshire Product Service
Department for repair. See the Service and Parts Policy section, page 34, of this
manual for packing and shipping information.

WARNING – MALFUNCTIONS
A cartridge can be “discharged” before it is chambered if its primer receives a sharp blow. If a cartridge hangs up, jams, or binds when being chambered or when being fed from the magazine into
the chamber, do not attempt to force it into the
chamber by pushing or striking the bolt. Any jam
or feeding problem is a signal to immediately stop
using the gun until it can be determined what is
wrong. Most failures of a cartridge to feed or to
chamber are caused by a damaged magazine,
improper gun handling, or defective ammunition.
Whatever the cause, cartridge jams can result in
the potentially dangerous situation of a cartridge
discharging before it is chambered. If this occurs,
the cartridge case will rupture and its fragments
will fly out of the gun with sufficient force to
cause injury. Always wear shooting glasses and
hearing protectors! Keep face away from chamber!

STRIKING RIM OR PRIMER
CAN BURST CARTRIDGE

WARNING – DISASSEMBLY
4

Always unload a firearm
before cleaning, lubrication,
disassembly or assembly.

2
1

Safety
"ON"

UNLOAD BEFORE CLEANING

DISASSEMBLY
Be Sure Rifle Is Unloaded!
Although The Mini Thirty Rifle can be disassembled, reassembled, and cleaned
in almost any surrounding, it is preferrable to carry out these procedures on a
workbench or table which has a covered top. A piece of shallow nap rug or an
old blanket is an ideal covering. Such a covering keeps the rifle from slipping
and being scratched.

1. With the rifle pointing in a safe
direction, safety “ON”, remove
the magazine by pushing catch
forward to release magazine,
while drawing magazine down
and forward (See Fig. 6).

1
2

2. Pull the slide handle all the way
to the rear and release. Make
sure safety is “ON” (See Fig. 7).
NOTE: Hammer must be cocked
and safety must be “ON” to
accomplish disassembly and
reassembly. Again, be sure chamber is empty!

Figure 7

Figure 6

3. Use a 1/4” diameter steel rod,
punch, screwdriver shank, or
other suitable instrument inserted into the hole in the rear of the
trigger guard as a lever to spring
open the trigger guard from its
latched position
(See Fig. 8).

Figure 8

WARNING: Do not use a cartridge to unlatch the trigger guard because of the danger of loosening the bullet in the cartridge case (See Warnings in “Ammunition”
section, p. 11).
Figure 9
4. Fold rear sight down. Invert rifle
and remove trigger housing
assembly by carefully pulling it
upward (See Fig. 9). Be careful
not to damage stock when removing or replacing the trigger housing assembly.

5. Remove barrel/receiver assembly from stock by swinging rear
end away from action slightly,
then pull stock out of engagement with gas block (See Fig.
10).

Figure 10

Figure 11a
11a

6. Remove buffer guide rod and recoil
spring (See Figs. 11a and 11b).
CAUTION: The spring is heavily
compressed -– use eye protection
and care when disassembling and
reassembling to prevent the rod
and spring from escaping forcibly
and possibly causing injury.

Figure 11b
11b

NOTE: When removing the buffer
guide rod, note positioning of the
projection on its end with relation
to the buffer cross pin. The long
tongue portion of the rod (“a”)
must go under the cross pin (“b”)
in Figure 11a, at the time of
reassembly.

7. Remove the buffer cross pin
and the buffer bushing if there
is any concern they will fall out
during remainder of disassembly. Note the position of the flat
on the buffer bushing.

8. Pull slide handle to the rear.
Align locking projections on
slide with disassembly notch on
receiver. Remove slide
(See Fig. 12).

9. Remove bolt lock cover plate by
carefully tapping downward
(with a soft-metal punch) at
point “a”. (See Fig. 13). With
cover plate removed, depress
bolt lock plunger, “b”, which
will allow ejector/bolt stop, “c”,
to be lifted out. (See “Caution”
in step 6, p. 24)

Figure 12

Figure 13

10. Pull the bolt forward until it
can be pivoted out of receiver.
Align firing pin projection with
slot in lower receiver bridge and
remove bolt from receiver (See
Fig. 14). NOTE: Bolt can be
removed from receiver with
ejector/bolt stop in place, but
bolt cannot be installed with
ejector/bolt stop in place.

Figure 14

Removal of the bolt stop assembly is not normally required for routine cleaning.

NOTE: The Mini Thirty Rifle is like the M1 Garand and many other types of
autoloading rifles in that the hammer can fall if the trigger is pulled when
the bolt is partially retracted. It is important for the shooter to realize that
the firing pin cannot contact the cartridge until the bolt is safely locked,
regardless of the position of the slide.

Removal of the gas block assembly is not necessary and is not advisable. The gas
block assembly is factory fitted using special fixtures and torque tools. Attempting
to fit the gas block assembly without the required special equipment can result in
damage to the components and malfunctioning of the rifle.
Further disassembly of the RUGER® MINI THIRTY RIFLE is not required
for normal cleaning purposes and should only be performed by a trained armorer
who is experienced in firearms repair.

REASSEMBLY
Again, Be Sure Rifle and Magazine are Completely Unloaded!
1. Reassembly of bolt into receiver:
(BOLT CANNOT BE RE-INSTALLED WITH EJECTOR/BOLT STOP IN PLACE)
a. Bolt can be reinserted by holding it at approximately a 45o angle to the receiver, with the rear end of the bolt angling downward. Insert the tail of the firing
pin through the slot in the receiver bridge, and “wiggle” the bolt until its rear
end moves back into the receiver. Then, push it forward to its closed and
locked position. It should rotate and move freely into place.
b. If you have removed the bolt stop (step 9, p. 25) reinsert the bolt lock plunger
and spring into its hole in the top of the receiver. Depress the plunger until
the rectangular cut in its side lines up with the round hole seen inside the
receiver on the left side. CAUTION! Plunger will now be under spring tension
and could cause injury if suddenly released. While holding the plunger against
its spring in this position, insert the bolt stop until its rectangular “tab” goes
into the rectangular cut on the bolt lock plunger. Sliding the bolt lock cover
plate upward (prying it upward slightly with a screwdriver if necessary) completes reassembly of the bolt lock. Note that the large inverted triangular protection on the cover plate goes on the outside of the rifle.
2. Reinstalling remaining parts of barrel/receiver group:
a. Retract bolt. Replace operating slide by angling the handle portion upward
between the handguard and receiver ring; then lower the slide so that the cam
track on the inside of the rod fits over the roller on the right locking lug of
the bolt, and the tab adjacent to the slide handle goes into its track on the
right side of the receiver.
b. Push operating rod fully forward. Be sure that the gas piston fits into the hole
in the front of the slide.
c. Replace buffer bushing (open end goes toward front) and cross pin. The cross
pin must be below flush with both sides of its hole. Be sure pin stays in place
for next step.
d. Hold action upside down as show in Figure 11b, p. 24. Carefully insert recoil
spring into hole in rear of slide, and compress the recoil spring until buffer
guide rod can be inserted into buffer bushing (the projection on the guide rod
should be between the buffer bushing cross pin and the barrel).
CAUTION! The recoil spring will be strongly compressed during this step and can
fly out with considerable force, possibly resulting in injury. Keep it under your
control and proceed with care.

3. Final reassembly of rifle:
a. Replace stock by inserting its front end into the gas block at a slight angle.
When the stock is correctly seated into the gas block, the stock can be
swung down into full contact with the receiver.
b. Insert the opened trigger housing assembly, safety “ON”, into the stock (the
hammer must be cocked prior to insertion). When fully seated, swing the
trigger guard fully into place until it locks shut. An audible “click” will be
heard when it is correctly locked. Cycle the slide handle and safety a few
times to be certain the components are correctly assembled. Put the safety
back “ON”.
c. Reinsert an empty magazine and fully withdraw slide. The bolt should lock
open automatically.
GUNS SHOULD NOT BE STORED LOADED!

REMOVAL AND REPLACEMENT
OF FIBERGLASS HANDGUARD
1. MAKE CERTAIN THE RIFLE CONTAINS NO CARTRIDGES AND THAT IT IS
POINTING IN A SAFE DIRECTION.
2. Remove the magazine. Leave the slide in the forward position.
3. With the rifle flat on its side, apply substantial thumb pressure, with both
thumbs, to the projecting underside of the handguard in the area of the retaining spring. (The spring is located underneath the circular projection on the
top of the handguard.) The pressure should be applied so as to raise the rear
portion of the handguard first.
4. To replace the handguard, put the forward end of the handguard under the top
portion of the gas block (as far forward as possible) and squeeze the handguard
down over the barrel.

MAGAZINE INSPECTION AND CARE
Check the magazine frequently. The follower must move freely and have adequate spring tension so that each cartridge is quickly raised to the feeding position.
To test the spring tension, load one cartridge into the magazine and then firmly
press against the cartridge case. Remove your finger quickly. The cartridge
should instantly and fully move in to the feeding position. If it does not, the
magazine should be cleaned. If cleaning does not restore proper spring tension,
do not use the magazine. (NOTE: After testing, remove the test cartridge).
When cleaning is necessary, use a solvent that will not rust the metal components or adversely affect the plastic magazine bottom. The magazine may be disassembled by placing a small screwdriver through the hole located in the magazine bottom and depressing the magazine bottom retainer. Carefully use the

screwdriver to push the magazine bottom rearward as you push down on the
spring-loaded bottom retainer. After the magazine bottom has been slid rearward
off the magazine shell, carefully raise the rear end of the bottom retainer so that
its two small lugs can be slid out the rear of the magazine and carefully remove
the bottom retainer. CAUTION! It is under spring tension from the magazine
spring. The magazine spring and follower may now be removed from the bottom
of the magazine shell, completing its disassembly. After the magazine has been
soaked in solvent to loosen foreign matter, be certain to shake it vigorously (with
the loading opening away from you) to remove solvent or residue from within
the magazine.
Reassembly of the magazine can be accomplished by hooking the magazine
spring into the hole in the magazine bottom from the right side. Reinsert this
assembly upwards into the magazine shell. Carefully compress the spring and
slide the bottom retainer on from the rear. Finally, press the bottom retainer
downward and slide the magazine bottom on from the rear.

Figure 15. Exploded view of the
Mini Thirty magazine components.
This illustration is included to
show the relationship and names
of the magazine components.

DAMAGED, NON-STANDARD, OR IMPROPERLY
ASSEMBLED MAGAZINES SHOULD NOT BE USED.
THEY CAN CAUSE THE RIFLE TO MALFUNCTION.

CARE AND CLEANING
BEFORE CLEANING, BE CERTAIN THE RIFLE AND ITS MAGAZINE CONTAIN NO CARTRIDGES.
At regular intervals, or whenever the rifle has been exposed to sand, dust,
extreme humidity, condensation, immersion in water, or other adverse conditions, disassemble, clean and oil it. Proper periodic maintenance is essential to
the reliable functioning of any firearm.
To clean the rifle, proceed as follows:
1. Disassemble (field-strip) the rifle to the extent described on pages 23 - 25.
2. Using a cleaning rod, run a solvent-wetted patch through the bore several
times. Then attach a solvent-wetted bristle brush to the rod and run it back
and forth the full length of the bore as many times as necessary to remove
grease and dirt from the bore and chamber. Clean bore with dry patches and
examine. Bore fouling can contribute to reduced accuracy, and grease accumulation in the chamber can interfere with proper feeding of cartridges from the
magazine.
3. Using powder solvent on a clean patch or bristle brush, remove powder residue
from all components of the mechanism. After cleaning, run a dry patch
through the bore, then follow with a patch that is very lightly oiled. Wipe all
surfaces clean with cloth, then wipe all surfaces with a patch or cloth that has
been very lightly oiled.
4. NOTE: Only a light application of oil is needed to provide adequate lubrication
of moving parts and to prevent rust. Excess accumulations of oil tend to
attract particles of dust and dirt and may congeal in cold weather which can
interfere with the safe and reliable function of the rifle.

WARNING – LUBRICATION

Firing a rifle with oil, grease, or any other
material even partially obstructing the bore
may result in damage to the rifle and serious
injury to the shooter and those nearby. Do not
spray or apply lubricants directly on ammunition. If the powder of a cartridge is affected by
the lubricant, it may not be ignited, but the
primer firing may push the bullet into the bore
where it may be lodged. Firing a subsequent
bullet into the obstructed bore may damage the
rifle and cause serious injury or death to the
shooter and those nearby. Use lubricants properly. You are responsible for the proper care and
maintenance of your firearms.

IMPROPER LUBRICATION
DESTROYS GUNS
29

STORAGE
GUNS SHOULD NOT BE STORED LOADED!
USE THE LOCKING DEVICE SUPPLIED WITH THE RIFLE FOR STORAGE.
(SEE PAGE 6)

Do not store the rifle in a leather case or scabbard. Leather attracts moisture,
even though it may appear to be dry.

TO RENDER THE RIFLE INOPERATIVE FOR SAFE STORAGE
With the muzzle pointed in a safe direction, remove the magazine, retract the
slide handle, and retract the bolt fully to the rear. Lock the bolt open and check
the chamber to be sure the rifle is completely unloaded! With the muzzle pointed in a safe direction, pull downward on the rear end of the trigger guard and
remove the trigger housing assembly from the bottom of the rifle.
Store the rifle and the trigger housing assembly in different locations. When disassembled in this manner, the rifle is inoperable. It is impossible to fire the rifle
until the trigger housing assembly has been correctly replaced.
To reassemble the rifle for firing, reinsert the trigger housing assembly into the
receiver from the bottom. Swing the trigger guard upward and rearward until it
latches securely in place. Check to be sure that the bolt can be operated fully and
freely by operating the slide handle back and forth. The rifle is now reassembled
and can be loaded and fired normally.
While the rifle is less likely to be used by unauthorized persons when disassembled in the above manner, it is always safest to store a firearm with the
supplied locking device correctly installed, or to store the firearm in a gun safe
or other secure location, away from children and unauthorized adults. Guns
should always be stored securely, unloaded and separate from their ammunition.

WARNING – STORAGE
Never place or store any firearm in
such a manner that it may be dislodged. Firearms should always be
stored securely and unloaded, away
from children and careless adults. Use
the locking device originally supplied
with this firearm for storage.
The use of a locking device or safety
lock is only one aspect of responsible
firearms storage. For increased safety,
firearms should be stored unloaded
and locked in a location that is both
separate from their ammunition and
inaccessible to children and any other
unauthorized person.

STORE SECURELY & UNLOADED
30

MAINTENANCE OF STAINLESS STEEL RIFLES
Firearms and components made of stainless steel are relatively more resistant to
corrosion than those of blued steel. However, in the interest of proper operation
and long life of a stainless steel firearm, inspect it frequently and clean, lubricate
and apply an appropriate rust preventative.
Sometimes discoloration occurs from perspiration or from contact with some
types of gun cases. Rusting may occur as a result of the firearm being exposed to
moisture, salt air or chemicals.
Minor discoloration can usually be removed by rubbing the stainless area with an
abrasive ink eraser, crocus cloth, or a “metal polishing” compound. When using
any of these abrasives, proceed with care and use light pressure to achieve a
blending of “color” with those areas that are not discolored. Do NOT use abrasives
on the clear coating of the aluminum alloy trigger housing.
External surfaces most subject to rusting from handling, or from exposure to the
elements should be cleaned and wiped dry after use or after exposure to adverse
conditions. If the rifle is to be stored, coat it with a light film of oil or preservative. Where the rifle is in continuing use, and the presence of oil or grease would
be objectionable, then the external surfaces can be coated (after cleaning and
drying) with a paste wax formulated for use on metals. Apply the wax sparingly,
allow time for it to dry hard, then buff lightly with a soft cloth. When applying
the wax, take care that it does not get into the mechanism or on the functioning
parts or in the bore.

ATTACHING RUGER SCOPE RINGS
Each Ruger telescope ring is a mated assembly of a top and a base. Do not mix
the parts of the two ring assemblies as they are not interchangeable. On the
underside of each mounting ring assembly there is an integral lug located off
center with respect to the front and back sides of the mount. The lug is nearer to
the front surface. By reference to the lug, the mounting can be correctly assembled with the front of the ring toward the muzzle of the rifle.

1. Fold rear sight down. Disassemble one ring and reassemble over the scope
body between the turret and the eyepiece. Remember - the lug on the base
should be on the front side of the scope.
2. Install the four top screws. Do not tighten.
3. Disassemble the other ring and install it on the forward section of the scope
tube with the lug forwardly also. Install the four top screws. Again, do not
tighten.
4. Assemble the rings to the receiver with the lugs engaging the recesses in the
top surface of the receiver. Tighten the clamp nuts so that the rings are locked
to the semicircular cuts on the sides of the receiver.
5. Rotate the scope until cross-hairs are aligned properly and slide scope to
desired eye relief. Then tighten the eight top screw each a bit at a time to grip
the scope body.
6. Sight in according to the directions with your scope.

SIGHT ADJUSTMENT
Shooting to determine the setting of the elevation slide (aperture) should be
done from a bench rest and over a measured distance.
The rear sight is adjustable for both windage and elevation. Lateral (windage)
adjustment is made by loosening the Rear Sight Windage Lock Screw (with the
hex-head wrench provided with the rifle) until the sight base requires finger pressure to be moved. (See illustration below). Move the sight in the direction you
wish to move the point of impact. Before moving the sight, pencil mark an index
line on the sight base and on the receiver so that the amount of sight movement
can be detected. After desired positioning of the sight base has been achieved,
tighten the lock screw firmly.

To Move Impact To Right
Move Sight Right

To Move Impact To Left,
Move Sight Left
1

WINDAGE ADJUSTMENT: To move the bullet impact point to the left, move
the rear sight base to the left. To move the bullet impact point to the right,
move the rear sight base to the right. Be sure to retighten lock screw after
adjustment.

To Move Impact Down,
Lower Sight

To Move Impact Up,
Raise Sight

ELEVATION ADJUSTMENT: To move the bullet impact point up or down, move
the elevation slide (the “peep”) by loosening both its screws (using a small
screwdriver with a blade tip that exactly fits the screw-head) only slightly so the
slide doesn’t move too freely. Move the slide in the direction you want the point
of impact of the bullet to move. When the slide is positioned at the desired
height, carefully retighten both screws.

SUGGESTED SIGHT PICTURE
The front sight is aligned in the
center of the rear sight aperture
(“peep”) and the target (bullseye) is
positioned to appear as if it is sitting on top of the front sight.

SERVICE AND PARTS POLICY
If you have any questions with regard to the performance of your RUGER®
MINI THIRTY RIFLE please write or call (603-865-2442) our Product
Service Department in Newport, New Hampshire 03773, fully describing all circumstances and conditions involved. If you should return your rifle to the factory
for repair, or order parts for it, please comply with the following suggestions for
prompt service:

WARNING: BEFORE SHIPPING ANY FIREARM,
BE ABSOLUTELY CERTAIN THAT IT AND ITS MAGAZINE ARE UNLOADED. DO NOT SHIP CARTRIDGES
WITH A FIREARM.

SHIPPING FIREARMS FOR REPAIR
RUGER® MINI THIRTY RIFLES returned to the factory for repair
should be sent to: Sturm, Ruger & Company, Inc., Product Service Department,
411 Sunapee St., Newport, New Hampshire 03773. Telephone (603) 865-2442.
Guns should be sent prepaid. We will not accept collect shipments.
The Federal Gun Control Act, as well as the laws of most States and localities, do
not prohibit an individual (who is not otherwise barred from purchasing or possessing a firearm) from shipping a firearm directly to the manufacturer for
repair. However, before you ship your rifle to us, be certain that your State or
locality does not have a law or regulation which will prohibit you from receiving
the rifle from us after it has been repaired. If such receiving is prohibited, then
please have a Federally Licensed firearms dealer ship the gun to us. If your rifle
is sent to us by a dealer, it will be returned to him after being repaired. If a handgun (pistol or revolver) is shipped by an individual who does not hold a Federal
Firearms License, it must be shipped via U.P.S. (Next Day Air) Persons who do
not hold a Federal Firearms License are prohibited by Federal law from shipping
a handgun by Mail. Handguns mailed in violation of the law are impounded by
the Post Office.
DO NOT SEND GUN BOXES OR LITERATURE THAT YOU CONSIDER TO BE
COLLECTOR’S ITEMS – THESE ARE INVARIABLY DAMAGED OR
DESTROYED IN SHIPMENT. Please do not include rifle case, sling, telescopic
sights or custom accessories with a firearm being shipped to the factory for service. Rifles and shotguns may be shipped via Parcel Post. Always insure your shipment.
Enclose a letter which includes your name, address, telephone number, serial
number and model of the firearm. Describe in detail the trouble you have experienced with your firearm, or the work you wish to have done. Merely stating that
the firearm “needs repair” is inadequate information.
Work performed will bear a net minimum labor charge of $20.00 plus a $12.00
shipping and handling charge. The charge for rebluing the RUGER® MINI
THIRTY RIFLE is $50.00 plus a $12.00 shipping and handling charge.
Custom gunsmithing service or nonstandard alterations are NOT AVAILABLE
from Ruger Product Service Departments.

WARNING –PARTS PURCHASERS
It is the purchaser’s responsibility to be absolutely certain that any parts ordered from the factory
are correctly fitted and installed. Firearms are
complicated mechanisms and IMPROPER FITTING OF PARTS MAY RESULT IN A DANGEROUS MALFUNCTION, DAMAGE TO THE
FIREARM, AND SERIOUS INJURY TO THE
SHOOTER AND OTHER PERSONS. The purchaser and installer of parts must accept full
responsibility for the correct adjustment and
functioning of the rifle after such installation.

PARTS MUST FIT CORRECTLY

ORDERING PARTS
Please contact the New Hampshire Product Service Department for parts availability and current prices. All parts orders for the RUGER® MINI THIRTY
RIFLE should be sent to: Sturm, Ruger & Co., Inc., Product Service
Department, 411 Sunapee Street, Newport, New Hampshire 03773, 603-8652442. We cannot comply with open account or C.O.D. orders. Payment in the
form of a check, money order, Visa or Mastercard must accompany your order.
Credit Card orders must include the account number, expiration date and
whether it is a Visa or Mastercard account. Minimum parts order is $1.00 plus
$3.50 shipping and handling charge. Order parts by Part Name and Part Number
and include the entire serial number of the firearm for which the parts are being
ordered. There is a minimum net labor charge of $20.00 plus $12.00 shipping
and handling charge if the parts are factory fitted. All factory fitted parts are fit
on an exchange basis only. We will not return the replaced parts.
Barrels, and a number of other component parts must be fitted at the factory.
Company policy is to proof-test and/or function fire all barrels after fitting to the
receivers in which they are to be used. This procedure ensures maximum protection to our customers. The special proof-test ammunition used in this testing is
sold only to bonafide firearms manufacturers and is not available to gun shops,
gunsmiths, or individuals.
Because the receiver of the RUGER® MINI THIRTY RIFLE is a serial
numbered component, it is defined as a “firearm” by Federal law and is not sold
as a separate component.
*Parts designated by an asterisk must be factory fitted. These parts are fitted on
an exchange basis only. We will not return the replaced parts. We will not return
any part that is broken, malfunctioning, badly worn or has been modified. See
“Warning – Parts Purchasers”, above.

CAUTION: A gun containing modified, broken, malfunctioning,
or badly worn parts should not be fired.
35

RUGER® MINI THIRTY RIFLE
PARTS LIST

Design, prices and specifications subject to change without notice.
SPECIFY MODEL WHEN ORDERING
(See Exploded View on Page 41)

*
*
*
*
*
*

Part Name
Barrel, Specify Model & Serial Number
Barrel, Specify Model & Serial Number
Bolt
Bolt
Bolt Assembly
Bolt Assembly
Bolt Lock Cover Plate
Bolt Lock Cover Plate
Bolt Lock Plunger
Bolt Lock Plunger
Bolt Lock Plunger Spring
Buffer Bushing
Buffer Bushing
Buffer Cross Pin
Buffer Cross Pin
Buffer Guide Rod
Buffer Guide Rod
Butt Plate

Part No.
0M8002
K0M8002
MS01003
KMS01003
MS11003
KMS11003
MS06700
KMS06700
MS04500
KMS04500
KMS04600
MS04010
KMS04010
MS06610
KMS06610
MS03901
KMS03901
C-63

Model
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
All Mini Thirty Models
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
Mini Thirty - Wood Stock Models

37
*
*

*
*

Part Name
Butt Plate Screw, (2 Req’d.)
Butt Plate Screw, (2 Req’d.)
Ejector Bolt Stop
Ejector Bolt Stop
Extractor
Extractor
Extractor Plunger
Extractor Spring
Firing Pin
Forearm Liner & Stock Cap Assembly
Forearm Liner & Stock Cap Assembly
Front Sight
Front Sight
Front Sight Cross Pin
Front Sight Cross Pin
Gas Block, Top & Bottom, (2 pieces)
Gas Block, Top & Bottom, (2 pieces)
Gas Block Screw, (4 Req’d.)
Gas Block Screw, (4 Req’d.)
Gas Pipe
Gas Pipe
Gas Port Bushing
Hammer
Hammer
Hammer Pivot Pin
Hammer Pivot Pin
Hammer Spring

Part No.
B-64
B-91
MS03211
KMS03211
MS01403
KMS01403
KMS01600
MS01500
KMS01103
MS02200
KMS02200
MS04403
KMS04403
MS07200
KMS07200
MS03503
KMS03503
MS06500
KMS06500
MS03600
KMS03600
KMS02503
MS01700
KMS01700
MS01900
KMS01900
KMS04700

Model
Mini Thirty - Wood Stock Models
Mini Thirty - Synthetic Stock Model
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
All Mini Thirty Models
All Mini Thirty Models
All Mini Thirty Models
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
All Mini Thirty Models
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
All Mini Thirty Models

Part Name
Hammer Strut
Hammer Strut
Hammer Strut Assembly
Hammer Strut Assembly
Handguard Assembly, Fiberglass
Magazine, Complete, 5-Shot Capacity
Magazine Bottom
Magazine Bottom Retainer
Magazine Follower
Magazine Latch
Magazine Latch
Magazine Latch Pivot Pin
Magazine Latch Pivot Pin
Magazine Latch Spring
Magazine Latch Spring
Magazine Shell
Magazine Spring
Pistol Grip Cap
Pistol Grip Cap Medallion
Pistol Grip Cap Screw
Rear Sight Assembly, Complete
Rear Sight Peep Blade
Rear Sight Windage Lock
Rear Sight Windage Lock Screw
Receiver
Receiver
Recoil Pad

Part No.
MS01800
KMS01800
MS01800A
KMS01800A
MFH
MAG/762
MS03404
MS02602
MS03004
MS03103
KMS03102
MS01200
KMS01200
MS05000
KMS05000
MS02704
MS02804
D-80SB
D-82
C-96SM
MS25501
MS05210
MS05910
MS05710
MS00103
KMS00103
D06315

Model
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
All Mini Thirty Models
All Mini Thirty Models
All Mini Thirty Models
All Mini Thirty Models
All Mini Thirty Models
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
All Mini Thirty Models
All Mini Thirty Models
Mini Thirty - Synthetic Stock Model
Mini Thrity - Synthetic Stock Model
Mini Thirty - Synthetic Stock Model
All Mini Thirty Models
All Mini Thirty Models
All Mini Thirty Models
All Mini Thirty Models
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
Mini Thirty - Synthetic Stock Model

Part Name
Part No.
Safety Assembly
MS13800A
Safety Assembly
KMS13800A
Safety Detent Spring
KMS04900
Safety Spring Retaining Pin
MS06200
Safety Spring Retaining Pin
KMS06200
Scope Ring Clamp
D-74
Scope Ring Clamp, Matte Finish
KD-74M
Scope Ring Nut
D-73
Scope Ring Nut, Matte Finish
KD-73M
Scope Base Torx® Head Screw (8 Req’d.)
MPF07600
Scope Base Torx® Head Screw (8 Req’d.)
KMPF07600
Scope Rings, Medium Rings
S100RM
Accommodates a 42mm Lens
Scope Rings, Medium Rings
KD72M-MATTE
Accommodates a 42mm Lens (stainless matte finish)
* Secondary Sear
MS02300
* Secondary Sear
KMS02300
Secondary Sear Spring
KMS02400
Slide Assembly
MS23703
Slide Assembly
KMS23703
Slide Spring/Recoil Spring
KMS05101
Sling, Carrying, Nylon, Not Illustrated
MA-132
Sling Swivel Assembly, Rear
MS07601
Sling Swivel Assembly, Rear
KMS07600

Model
Mini Thirty - Blued Model
Mini Thirty - Stainless Model
All Mini Thirty Models
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
Mini Thirty - Wood Stock Models
Mini Thirty - Synthetic Stock Model
Mini Thirty - Wood Stock Models
Mini Thirty - Synthetic Stock Model
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
All Mini Thirty Models
All Mini Thirty Models
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
All Mini Thirty Models
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
All Mini Thirty Models
All Mini Thirty Models
Mini Thirty - Blued Model
Mini Thirty - Stainless Models

Part Name
Sling Swivel, Front
Sling Swivel, Front
Stock (Wood w/Butt Plate Attached)
Stock Assembly, Complete, Synthetic
Stock Reinforcement Assembly
Stock Reinforcement Assembly
Stock Reinforcement Lock Washer,
(2 Req’d.)
Stock Reinforcement Screw, (2 Req’d.)
Stock Reinforcement Screw, (2 Req’d.)
Torx® Key Wrench, Not Illustrated
(for scope base Torx® Head Screw)
* Trigger
* Trigger
Trigger Bushing
Trigger Bushing
Trigger Guard
Trigger Guard
Trigger Housing
Trigger Housing
Trigger Housing
Trigger Pivot Pin
Trigger Pivot Pin
Trigger Spring

Part No.
MS07500
KMS07500
MS00403
KMS30427
MS20702
KMS20702
MS08000

Model
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
All Mini Thirty Models
Mini Thirty - Synthetic Stock Model
Mini Thirty - Blued Model
Mini Thirty - Stainless Model
All Mini Thirty Models

MS06900
KMS06900
MPF07601

Mini Thirty - Blued Model
Mini Thirty - Stainless Model
All Mini Thirty Models

MS02000
KMS02000
MS04300
KMS04300
MS00200
KMS00200
P01300
KP01300
KMS01301
MS02100
KMS02100
KMS04800

Mini Thirty - Blued Model
Mini Thirty - Stainless Models
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
Mini Thirty - Blued Model
Mini Thirty - Stainless Model
Mini Thirty - Synthetic Stock Model
Mini Thirty - Blued Model
Mini Thirty - Stainless Models
All Mini Thirty Models

* PARTS SO MARKED MUST BE FACTORY FITTED

RUGER® MINI THIRTY RIFLE
EXPLODED VIEW

THE BASIC RULES OF SAFE FIREARMS HANDLING
We believe that Americans have a right to purchase and use firearms for lawful
purposes. The private ownership of firearms in America is traditional, but that
ownership imposes the responsibility on the gun owner to use his firearms in a
way which will ensure his own safety and that of others. When firearms are used in
a safe and responsible manner, they are a great source of pleasure and satisfaction,
and represent a fundamental part of our personal liberty.
Firearms do not cause accidents! Firearms accidents are almost always found to
have been the result of carelessness, or ignorance on the part of the shooter of the
basic rules of safe gun handling.
The following rules must be observed by gun users at all times. Safe gun handling
is not just desirable, it is absolutely essential to your safety, the safety of others, and
the continuation of gun ownership and sport shooting as we know it today.

1. LEARN THE MECHANICAL AND HANDLING CHARACTERISTICS OF THE FIREARM YOU ARE USING.

R U G E R AL

MANU
CTION
INSTRU
CTIONS
E INSTRU
READ TH NINGS IN THIS
RE
AND WARCAREFULLY BEFO
L
MANUA IS FIREARM.
USING TH

Not all firearms are the same. The
method of carrying and handling
firearms varies in accordance with
the mechanical provisions for avoiding accidental discharge and the various proper procedures for loading
and unloading. No person should
handle any firearm without first having thoroughly familiarized himself
with the particular type of firearm he
is using, and with safe gun handling
in general.

2. ALWAYS KEEP THE
MUZZLE POINTED IN A
SAFE DIRECTION.
Be sure of the bullet stop behind
your target, even when dry-firing.
Never let the muzzle of a firearm
point at any part of your body or at
another person. This is particularly
important when loading or unloading a firearm. In the event of an accidental discharge, no injury can occur
as long as the muzzle is pointing in a
safe direction. A safe direction means
a direction which will not permit a
discharged bullet to strike a person,
or to strike an object from which the
bullet may ricochet.
42

A safe direction must take into account the fact that a bullet may penetrate a wall, ceiling, floor, window, etc., and strike a person or damage
property. Make it a habit to know exactly where the muzzle of your gun
is pointing whenever you handle it, and be sure that you are always in
control of the direction in which the muzzle is pointing, even if you fall
or stumble. Keep your finger off the trigger until you are ready to shoot.

3. FIREARMS SHOULD BE UNLOADED WHEN NOT IN
USE.
Firearms should be loaded only when you are in the field or on the target
range or shooting area, ready to
shoot. Firearms and ammunition
should be securely locked in safes,
racks or cabinets, or by using the
locking device supplied with the
firearm, when not in use.
Ammunition should safely be
stored separate from firearms.
Store your firearms out of sight of
visitors and children. It is the gun
owner’s responsibility to be certain
that children and persons unfamiliar with firearms cannot gain
access to firearms,
ammunition, or components.
4

Safety
"ON"

4. BE SURE THE BARREL IS CLEAR OF OBSTRUCTIONS
BEFORE SHOOTING.
Even a bit of mud, snow or excess
lubricating oil or grease in the
bore may cause the barrel to
bulge, or even burst on firing, and
can cause serious injury to the
shooter and bystanders. Be sure
that you are using ammunition of
the proper caliber and loading for
the gun you are using. If the
report or recoil on firing seems
weak, or doesn’t seem quite right,
CEASE FIRING IMMEDIATELY,
unload your firearm, and check to
be sure that no obstruction has
become lodged in the barrel. Never
try to shoot out an obstruction!

5. BE SURE OF YOUR
TARGET BEFORE YOU
SHOOT.
Don’t shoot unless you know
exactly where your bullet is going
to strike. Be sure of the bullet
stop behind your target, even
when dry-firing with an unloaded
gun. If you are in the field hunting, do not fire at a movement or
noise. Take the time to be
absolutely certain of your target
before you pull the trigger.

6. WEAR SHOOTING
GLASSES AND HEARING
PROTECTORS WHEN
YOU SHOOT.
All shooters should wear protective shooting glasses and adequate hearing protectors when
shooting. Exposure to shooting
noise can damage hearing, and
adequate eye protection when
shooting is essential.

7. NEVER CLIMB A TREE
OR FENCE WITH A
LOADED FIREARM.
Put the firearm down carefully
before climbing a fence, and
unload it before climbing or
descending a tree or jumping over
a ditch or other obstruction. Never
pull or push a loaded firearm
toward yourself or another person.
When in doubt, or whenever you
are about to do anything awkward,
unload your gun!

8. DON’T SHOOT AT A
HARD SURFACE, OR AT
WATER.
Bullets can glance off many surfaces like rocks or the surface of
water and travel in unpredictable
directions with considerable
velocity.

9. NEVER TRANSPORT A
LOADED FIREARM.
Firearms should always be
unloaded before being placed in a
vehicle. A suitable carrying case
or scabbard should be used to
carry an unloaded firearm to and
from the shooting area.

10. AVOID ALCOHOLIC
BEVERAGES WHEN
SHOOTING.
Don’t drink until the day’s shooting is over. Handling firearms
while under the influence of alcohol in any form, or medications
that could affect your judgement
or co-ordination, constitutes a
criminal disregard for the safety
of others.

A BRIEF ACCOUNT OF AN EXTRAORDINARY
ACHIEVEMENT: RUGER FIREARMS
One of the few American firearms manufacturers whose management has remained unchanged since starting in business, Sturm, Ruger &
Company, Inc., had its beginning in a small machine shop occupying a
rented frame building in Southport, Connecticut. In January, 1949, with
an initial investment of only $50,000 and an idea, William B. Ruger and
Alexander M. Sturm started production of a .22 caliber autoloading pistol
– a design which was so successful that it became the cornerstone upon
which one of the most comprehensive lines of sporting firearms ever made
in America was established. After Alex Sturm’s death in 1951, William B.
Ruger continued to direct the company alone and today, as Chairman
Emeritus of the Board, he continues to provide the guidance which has
made this 52-year-old company a sound and successful enterprise.
Sturm, Ruger & Company, in this relatively short time, has established
itself as a leading small arms design organization, developing a unique and
broad line of fine quality sporting, military and police firearms to become
one of the world’s most famous producers of revolvers, pistols, rifles and
shotguns. From 1949 thru 2001 Ruger craftsmen have built many millions
of firearms.
During its five decades of growth and progress under the leadership of
William B. Ruger, the company has developed a business philosophy and
implemented policies which represent a constructive influence in the life
of modern America. From the beginning, Sturm, Ruger & Company played
a positive role in conservation efforts and has supported the interests of
shooters through such groups as the National Rifle Association, National
Shooting Sports Foundation, and many regional sportsmen’s organizations. The company has always endeavored to market its firearms for constructive and recreational purposes, to emphasize the traditional aspects of
shooting, to render meaningful public services and to encourage shooters
in constructive, responsible, and safe participation in the shooting sports.
Today, Sturm, Ruger & Company is particularly mindful of those elements
which have contributed to the creation of its success, and extends heartfelt
thanks to its many loyal employees and customers.

A current catalog of Ruger firearms is available free upon request to
Sturm, Ruger & Co., Inc., Southport, CT 06490.

WHY NO WARRANTY CARD HAS BEEN
PACKED WITH THIS NEW RUGER FIREARM
The Magnuson-Moss Act (Public Law 93-637) does not require any
seller or manufacturer of a consumer product to give a written warranty. It does provide that if a written warranty is given, it must be
designated as “limited” or as “full” and sets minimum standards for a
“full” warranty. Sturm, Ruger & Company, Inc. has elected not to provide any written warranty, either “limited” or “full”, rather than to
attempt to comply with the provisions of the Magnuson-Moss Act and
the regulations issued thereunder. There are certain implied warranties under state law with respect to sales of consumer goods. As
the extent and interpretation of these implied warranties varies from
state to state, you should refer to your state statutes. Sturm, Ruger &
Company wishes to assure its customers of its continued interest in
providing service to owners of Ruger firearms.

STURM, RUGER & Company, Inc.
Southport, Connecticut 06490 U.S.A.
http://www.ruger.com
“Arms Makers For Responsible Citizens”
A COPY OF THE INSTRUCTION MANUAL FOR ANY RUGER
FIREARM IS AVAILABLE FROM THE FACTORY FREE ON REQUEST.
THESE INSTRUCTION MANUALS CONTAIN IMPORTANT
WARNINGS WHICH MUST BE UNDERSTOOD
BEFORE USING THESE FIREARMS.

“RUGER”, the Sturm, Ruger logo, “SINGLE-SIX”, “BLACKHAWK”, “REDHAWK”, “SECURITY-SIX”,
“SPEED-SIX”, “SERVICE-SIX”, “BEARCAT”, “OLD ARMY”, “10/22”, “MINI-14”, “MINI THIRTY”,
“RANCH RIFLE”, “M77”, “77/22”, “GP-100”, “SP101”, “P-85” and “VAQUERO”
are registered U.S. trademarks.
“77/50” is a Ruger trademark.

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Create Date                     : 2003:01:21 19:45:11Z
Modify Date                     : 2003:01:22 09:21:57-08:00
Page Count                      : 46
Creation Date                   : 2003:01:21 19:45:11Z
Mod Date                        : 2003:01:22 09:21:57-08:00
Producer                        : Acrobat Distiller 5.0.5 for Macintosh
Author                          : Kevin Sperrazza
Metadata Date                   : 2003:01:22 09:21:57-08:00
Creator                         : Kevin Sperrazza
Title                           : mini 30revised

EXIF Metadata provided by EXIF.tools

Mini 30revised PDF Ruger Mini30

Ruger Mini-30 Ruger Mini-30

Navigation menu

Versions of this User Manual:

Views

Navigation