Simac PastaMatic MX700 Simac_pastamatic_instructions Instructions
User Manual: simac_pastamatic_instructions Fante's Kitchen Shop
Open the PDF directly: View PDF 
.
Page Count: 12
| Download | |
| Open PDF In Browser | View PDF |
Simac PastaMatic MX700 Contents: Assembly Instructions How to Use the PastaMatic Troubleshooting Tips Extruding Discs Parts & Service Manuals The Simac PastaMatic MX700 electric pasta maker makes approximately 1-1½ Lbs of pasta. It comes with 6 extruding discs, a specially sized and marked liquid measuring cup, and a special wrench for changing discs. To get good results, it is important to follow all the instructions and measure ingredients accurately. The dough will seem different from that which is kneaded by hand, and it is essential to know this difference. For basic pasta, you will need flour, plus water or whole eggs. Start with bleached, all purpose flour. Humidity can affect its volume, so use a scale to measure the flour accurately. With some practice, you can experiment with other types of flour after you become familiar with how the dough should feel when it is ready to be extruded. You will also need a flour sifter, timer, and possibly measuring spoons. For other types of flour, the right consistency of the dough is crucial for proper extrusion and to avoid damaging the machine. This consistency differs from that used with manual pasta makers, so we recommend that you start with the basic pasta recipe indicated below, using all purpose flour. You can then use the desired flour and adjust its consistency accordingly during kneading. For a full recipe, plan on using a 10 qt stock pot, filled with 8 qts of water. Add 2 tablespoons of salt when boiling and before adding pasta. You can also add a tablespoon of oil, if you wish, to keep pasta strands from sticking to each other. Add the pasta to the boiling water and start checking for doneness after 30 seconds. Tubular and thicker pasta takes longer. Use it freshly made, for best taste. For use within a few hours, flour and wrap it airtight in plastic wrap and store in the refrigerator. To store it for later use, place it in an airtight container, flouring generously and layering to prevent sticking, and put it in the freezer. It will take longer to cook pasta that is stored. Specifications: UL Listed, 120 VoltsAC, 60 Hz, 2.3 Amps, Max 230 Watts Limited continued use: 20 minutes Equipped with automatic safety device with off switch Weighs 15.6 Lbs 9.75" x 9.75" x 10.25" high 11" deep with Ring Nut in place Made in Italy Simac and PastaMatic are Registered Trademarks Warranty: The PastaMatic MX700 is covered by a one year Limited Warranty covering defects in materials or workmanship. Within the warranty period, DeLonghi will repair or replace such defectives at no other cost than shipping it to a service center. Complete details are on the warranty card included with the machine. Assembly Instructions Here you will learn to assemble (and disassemble) the machine properly. · Step 1. Place the base on a clean, dry surface near an electrical outlet, with the logo facing you. Slide the rotary housing all the way into the open side of the base, ridged side down and rectangular opening facing up. · Step 2. Insert the rotary screw, metal end first, all the way into the rotary housing. It will be necessary to rotate the screw for it to fit in completely. The end of the screw should be flush with the end of the rotary housing. · Step 3. Grasp the shutter slide, and firmly push it all the way into the slot over the rotary housing. It will click in place. · Make sure slide is fully in place before adding any ingredients. Look down inside the bowl to make sure the slide completely covers the opening in the bottom of the bowl. The slide must remain closed securely in place during the mixing cycle to avoid ingredients from entering the rotary housing prematurely, clogging and possibly damaging it. · Step 4. Insert the bowl onto the base, matching the notch on the top edge of the bowl with the tab of the opening located towards the front of the base, and pressing down firmly. · Step 5. Fit the blade, kneading foot down, over the central metal shaft extending up through the bowl. Rotate it until it sits firmly down on the bottom. · Step 6. Place the locking nut on top of the blade shaft and turn it clockwise until it is firmly in place. Your machine is now assembled and ready to work. To operate the Pastamatic: · The bowl must be firmly in place; · The bowl cover lip must be inserted in the slot in back; · The latch must be securely locked in the front. How to Use the PastaMatic Recipe Needs: 1 lb bleached all purpose flour 4 eggs or water Measuring spoons Flour sifter Timer Scale These instructions will help you to make about 1½ Lb of pasta. You can make about ¾ Lb of pasta by using half the ingredients and measures on the cup provided. Read through all the instructions before starting. Extruder discs, liquid measuring cup and electric cord are stored in the compartment located at the rear of the unit. See above for more details on assembling the PastaMatic. · Step 1. Check to be sure the main switch is turned "OFF." (When it sticks out, it is "OFF;" when it is pushed in, it is "ON.") Be sure the bowl is empty of all accessories. Push the Shutter Slide all the way into the slot. · Step 2. Put the bowl in place by inserting it into the main housing with the Bowl's Locking Tab fitted to the Bowl Locking Notch, toward the front of the PastaMatic. · Step 3. Put the cover in place by first fitting the Cover Lip into the Slot toward the rear of the top. Push in the Cover Latch and press down to lock the cover. Plug the electric cord into a grounded 3-prong outlet and push the ON/OFF switch to turn it ON. If it does not turn on, remove and replace both the cover and the bowl, making sure they are positioned correctly. · Step 4. Now that you know the unit is working properly, unlatch the cover and remove it. Make sure the slide is fully in place before adding any ingredients. Check from above the bowl to make sure the space at the bottom is fully covered by the closed Shutter Slide. If it is not fully closed, flour and other ingredients can clog and permanently damage the PastaMatic. · Step 5. Measure One Pound of flour, preferably using a scale for greater accuracy and more consistent results. (1 Lb of flour is approximately 3.25 cups dry measure, and 3.75 cups when sifted; humidity and grade of flour can affect this measure. Do yourself a favor and buy a scale.) Place the flour into the mixing bowl. Put the cover in place and lock it shut. Turn the PastaMatic ON. · Step 6. Use either water OR whole eggs. Fill to the 1 Lb line on the cup. Be precise with your measurements. The left side shows the Water measurements and the right side shows the Whole Eggs measurement. The 1 Lb and ½ Lb markings refer to the amount of flour being used. · Step 7. Slowly pour the eggs OR water through the liquid intake hole in the lid. Begin to time the kneading process. · Step 8. Allow the dough to knead for 3 minutes, then unlatch the cover, remove it, and check the consistency of the dough. The consistency is correct when the dough looks like walnut-size lumps that are moist, but not sticky. The dough is too dry if feels floury in small granules. To correct, add 1 teaspoon of water. Close the cover and let knead for 3 more minutes. You can't overknead the dough. The dough is too wet when it feels sticky in large, smooth balls. To correct, add 3 tablespoons of flour. Close the cover and let knead for 3 more minutes. You can't overknead the dough. · Step 9. Unlatch the cover, remove it, and check the consistency of the dough. If it feels too wet or too dry, repeat Step 8 above. You are ready to begin the extrusion process when the dough looks like walnut-sized lumps that are moist, but not sticky. Turn the PastaMatic OFF by pressing the ON/OFF switch so that the button sticks out. Replace and lock the cover. · Step 10. Pull out the Slide, then turn the PastaMatic ON. It will take about one minute for dough to start coming out of the open end of the Rotary Housing. Let the machine run until a couple of the larger sized lumps begin to come out. Turn the machine OFF by pressing the ON/OFF switch so that the button sticks out. Replace the lumps of dough into the Mixing Bowl, and replace and lock the cover. · Step 11. Choose a disc, immerse it for a second in warm water and set it in place on the end of the Rotary Housing. Some discs have three tabs on the back, that must line up with the notches on the Rotary Housing. Screw the Ring Nut in place over the disc, for a fit snug. · Step 12. Turn the machine ON by pressing the ON/OFF button. It will take about 2 minutes for extruded pasta to emerge from the disc. Remove the first 2 or 3 inches of pasta and place it back into the Mixing Bowl. The pasta should now extrude smoothly. Cut to the desired length. · Step 13. When all the dough is out of the Mixing Bowl and very little is extruding, stop the machine. Turn the PastaMatic OFF by pressing the ON/OFF switch so that the button sticks out. Remove the Ring Nut using the Wrench, and remove the disc. Turn the PastaMatic ON by pressing the ON/OFF switch, and let the remaining dough extrude from the open Rotary Housing. Keep hands away from this area. · Step 14. Disassemble the machine, remove excess dough, and leave the parts to dry completely. You can let them dry overnight. Rap the disc sharply against the counter and the dough will fall right out. Wash the disc and other parts completely. All removable parts are toprack dishwasher safe. Dry parts thoroughly, reassemble, and store. WHAT TO DO IF... Troubleshooting Hints ...pasta sticks together This may happen more likely if the strands are thin, but the real reason as it comes out of the is because the dough was too wet before the extrusion. machine Lightly oil or flour your hands and run the pasta through to coat it as it comes out of the machine. Remember to check the dough next time, for proper consistency, before you begin to extrude. ...strands aren't all the same length Hold strands out as they extrude, or the bottom strands will be shorter than the upper strands. ...strands are raggedy This should improve somewhat as the dough extrudes and the disc gets warmer. along the edges It will only affect the first 20 or so inches or pasta. Cut the strands that are raggedy and put them back in the Mixing Bowl. ...dough revolves around blade and isn't pushed out by kneading foot; strands come out gummy and stick to each other This dough is too wet. Replace the Shutter Slide and remove the disc. Add a little more flour and knead until proper consistency, for 3 to 5 or more minutes more. Then remove the Shutter Slide, attach the disc and continue the extrusion process. ...cover pops open and Push the dough down into the Mixing Bowl, or remove some of the dough so that it won't rise all the way up the bowl to the cover as it stops the machine kneads. You can add the dough back later. ...dough is almost used up and what remains won't go through Stop the machine, remove the cover and break the remaining dough into pieces small enough to fit into the hole at the bottom of the bowl. Dough should now come through the disc. This can happen if the dough was too wet before the extrusion. Remember to check the dough the next time, for proper consistency, before you begin to extrude. ...flour sprinkles out Don't pull the Shutter Slide out completely. of shutter slide opening while pasta is You can leave it in part way as long as it doesn't block the dough from dropping into the Rotary Housing chamber. extruding Let the pasta dry after disassembling the housing and discs. ...you want a quick way to clean the parts Just tap each piece on a hard surface, and the dried pasta will fall right after making the off. dough ...dough sticks in deep Put disc in freezer for 10 minutes, tap on a hard surface and clean up with a nut pick, if necessary. slots of some discs and is hard to flake The frozen dough should come off easily. away to clean ...you don't want to cook the pasta right away Wrap it airtight in plastic wrap and refrigerate if storing for only several hours. Or, the dough can be wrapped airtight in plastic wrap, aluminum foil or airtight container, and frozen until you want to use it. Re-read the directions, then contact the distributor, listed at the bottom ...these hints don't answer your question of this page. The model and serial numbers of your PastaMatic are on a label either on the back or on the bottom of the unit. PastaMatic Discs 6 discs* are included with the Simac PastaMatic MX700 Others available from the distributor (see below). Discs fit Simac, Lello, Cuisinart and DeLonghi Pasta Makers. #1 Capellini (Angel Hair) * #2 Spaghetti * #5 Linguine * #6 Small Fettuccine * #9 Sfoglie (Lasagne) #13 Penne (Ziti) #10 Bucatini (Hollow Spaghetti) #14 Maccheroni (Macaroni) * #3 Spaghettoni (Large Spaghetti) #4 Chitarre (Square Spaghetti) #7 Tagliatelle (Fettuccine) #8 Pappardelle (Large Fettuccine) #12 Bucato #11 Bucatini (Large Hollow Rigati Spaghetti) (Ridged Hollow Spaghetti) #15 Pizza (Pizza Dough) #16 Cookies * #17 Grissini (Breadsticks) #18 Gnocchi #19 Conchigliette (Small Shells) #20 Pasta Del Contadino (Farmer's Pasta) #21 Fili D'Oro (Golden Threads) #22 Maccheroni Quadrati (Square Macaroni) #23 Maccheroni Quadrifoglio (Clover Macaroni) #24 Sfoglia Larga per Ravioli (Wide Width for Ravioli) All the discs for the Simac (MX 700, PastaMatic 1000, PastaMatic 1400) also fit the Lello (PastaMaster 2200 and PastaMaster 3000PRO), the DeLonghi (PastaMatic), and the Cuisinart pasta machines. FOR PARTS & SERVICE, CONTACT: De'Longhi www.delonghi.com 800-865-6330 (8:30 am – 5:00 pm EST Mon -Fri) www.delonghi-accessories.com By Mail: Fox International 23600 Aurora Rd., Bedford Heights, OH 44146 Simac-Vetrelli S.p.A., Italy Divisione Commerciale SIMAC De'Longhi Appliances Via L. Seitz, No. 47, 31100 Treviso (TV) - Italy Tel. + 39 0422 4131 Fax + 39 0422 41309 www.simac-vetrella.com Manuals: Simac PastaMatic Recipe Book (11.5MB) Simac PastaMatic 1400, 1000, and 700 User Manual & Recipes (3.5MB) Current as of 3/17/10
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Producer : Acrobat Distiller 8.1.0 (Windows) Source Modified : D:20100319003628 Create Date : 2010:03:18 20:43:47-04:00 Modify Date : 2010:03:21 00:56:12-04:00 Creator Tool : Acrobat PDFMaker 8.1 for Word Metadata Date : 2010:03:21 00:56:12-04:00 Document ID : uuid:ebf90d1b-bc5c-427b-bc4b-84f72a6202fe Instance ID : uuid:d07d0e35-6118-420a-81c9-99639f96b53c Subject : 2 Format : application/pdf Creator : Simac Title : Simac PastaMatic MX700 Description : Simac PastaMatic MX700 User Manual Page Count : 12 Page Layout : OneColumn Author : SimacEXIF Metadata provided by EXIF.tools