XRC8 10 12 Instructions Smb97281
User Manual: smb97281
Open the PDF directly: View PDF 
.
Page Count: 17
| Download | |
| Open PDF In Browser | View PDF |
PARTS INCLUDED Winch Solenoid Box Hardware Bag QTY 1 1 1 PARTS INCLUDED Roller Fairlead Clevis Hook Remote Control QTY 1 1 1 SAFETY PRECAUTIONS Warning! Observe safety precautions for personal safety and the safety of others. Improper equipment operation may cause personal injury and equipment damage. Read the following carefully before attempting to operate your winch and keep the instructions for future reference. 1. Dress Properly: -Don’t wear loose clothing or jewelry. They can be caught in moving parts. -Wear leather gloves when handling winch cable. Do not handle cable with bare hands as broken wires can cause injuries. -Non-skid footwear is recommended. -Protective hair covering to contain long hair. 2. Keep a Safe Distance: -Ensure that all persons stand well clear of winch cable and load during winch operation, 1.5 times the cable length recommended. If a cable pulls loose or breaks under load it can lash back and cause serious personal injury or death. -Don’t step over the cable. -All visitors and onlookers should be kept away from the work area. -Keep proper footing and balance at all times. 3. Don’t Abuse the Cord: -Never carry your winch by the cord or yank it to disconnect it from the receptacle. -Keep cord from heat, oil and sharp edges. 4. Don’t Overwork the winch: - If the motor becomes uncomfortably hot to touch, stop and let it cool for a few minutes. - Don’t maintain power to the winch if the motor stalls. - Don’t exceed maximum line pull ratings shown in tables. Shock loads must not exceed these ratings. 5. Avoid Unintentional Starting: - Winch clutch should be disengaged when not in use and fully engaged when in use. 6. Check Damaged Parts: - Before using, you should check your winch carefully. Any part that is damaged should be properly repaired or replaced by an authorized service centre. 7. Repair Your Winch: - When repairing, use only identical replacement parts or it may cause considerable danger to the user. 8. Re-spool the cable: - Leather gloves must be worn while re-spooling. To re-spool correctly, it is necessary to keep a slight load on the cable. Hold the cable with one hand and the remote control switch with the other. Start as far back and in the centre as you can .Walk up keeping load on the cable as the winch is powered in. - Do not allow the cable to slop through your hand and do not approach the winch too closely. - Turn off the winch and repeat the procedure until all the cable except 1m is left. - Disconnect the remote control switch and finish spooling in cable by rotating the drum by hand with clutch disengaged. -On hidden winches, spool in cable under power but keep hands clear. For Technical Support/Warranty Information please call 310-762-9944 Smittybilt, 400 West Artesia Blvd, Compton, CA 90220 Page 2 of 17 Warning: The use of any other accessory or attachment other than those recommended in the Fitting Instructions may present a risk of personal injury. WINCH OPERATION WARNINGS Read the following carefully before attempting to operate your winch and keep the instructions for future reference. 1. The uneven spooling of cable, while pulling a load, is not a problem, unless there is a cable pile up on one end of the drum. If this happens reverse the winch to relieve the load and move your anchor point further to the centre of the vehicle. After the job is done， you can un-spool and rewind for a neat lay of the cable. 2. Store the remote control switch inside your vehicle where it will not become damaged, inspect it before you plug it in. 3. When ready to begin spooling in, plug in remote control switch with clutch disengaged, do not engage clutch with motor running. 4. Never connect the hook back to the cable. This causes cable damage. Always use a sling or chain of suitable strength. 5. Observe your winch while winching, if possible while standing at a safe distance. Stop the winching process every meter or so to assure the cable is not piling up in one corner. Jamming the cable can break your winch. 6. Do not attach tow hooks to winch mounting apparatus. They must be attached to vehicle frame. 7. The use of a snatch block will aid recovery operations by providing a doubling of the winch capacity and a halving of the winching speed, and the means to maintain a direct line pull to the centre of the rollers. When double loading during stationary winching, the winch hook should be attached to the chassis of the vehicle. 8. Ensure rated ”D” or bow shackles are used in conjunction with an approved tree trunk protector to provide a safe anchor point. 9. When extending winch cable, ensure that at least FIVE (5) wraps of cable remain on drum at all times. Failure to do this could result in the cable parting from the drum under load. Serious personal injury or property damage may result. 10. All winches are provided with a Red Cable marking to identify that 5 cable wraps remain on the winch drum when this mark appears at the rollers. No recovery should be attempted beyond this marking. 11. Since the greatest pulling power is achieved on the innermost layer of your winch, it is desirable to pull off as much line as you can for heavy pulls (you must leave 5 wraps minimum on the drum-red cable). If this is not practical use a snatch block and double line arrangement. 12. Draping a heavy blanket or similar object over the extended winch cable is recommended as it will dampen any back lash should a failure occur. 13. Neat, tight spooling avoids cable blinding, which is caused when a load is applied and the cable is pinched between the others. If this happens, alternatively power the winch in and out. Do not attempt to work a bound cable under load, free by hand. 14. Apply blocks to wheels when vehicles are on an incline. 15. Battery: - Be sure that the battery is in good condition. Avoid contact with battery acid or other containments. - Always wear eye protection when working around a battery. - Have the engine running when using the winch, to avoid flattening the battery. 16. Winch cable: - Be sure that the cable is in good condition and is attached properly. - Do not use the winch if cable is frayed. - Do not move the vehicle to pull a load. For Technical Support/Warranty Information please call 310-762-9944 Smittybilt, 400 West Artesia Blvd, Compton, CA 90220 Page 3 of 17 - - Do not replace the cable with a cable of lesser strength. The life of cable is directly related to the use and care it receives. Following its first and subsequent uses, a cable must be wound onto the drum under a load of at least 500lbs (230kg) or the outer wraps will draw into the inner wraps and severely damage the cable during winching. The first winch use should be a familiar run while in a relaxed, non-recovery situation. Spool out the cable until the red cable mark appears (about five wraps on the drum), when rewind the cable onto the drum under a load of 500lbs (230kg) or more. This will slightly tension and stretch the new cable and create a tight cable wrap around the drum. Failure to do so may result in cable damage and reduced cable life. When the cable is replaced, be sure to apply locktite, or the cable clamp thread. Tighten the clamp screw properly but do not over-tighten. The lockkite will prevent loosening of the screw in arduous conditions. Locktite 7471 primer and 222 Thread Locker are recommended. 17. Do not attempt to exceed the pulling limits of this winch. 18. Do not drive your vehicle to assist the winch in any way. Vehicle movement in combination with winch operation may overload the cable, the winch itself or cause damaging shock loads. 19. Shock loads when winching are dangerous! A shock load occurs when an increased force is suddenly applied to the cable. A vehicle rolling back on a slack cable may induce a damaging shock load. 20. The winches shown in this manual are solely for vehicle and boat mount, non-industrial applications. 21. Do not use winch in hoisting applications due to required hoist safety factors and features. 22. Do not use the winch to lift, support or otherwise transport personnel. 23. Do not move your winch by lifting the cable leads or the clutch handle lever. For Technical Support/Warranty Information please call 310-762-9944 Smittybilt, 400 West Artesia Blvd, Compton, CA 90220 Page 4 of 17 INSTALLATION MOUNTING YOUR WINCH 1 a) The winch is to be mounted into a suitable steel mounting frame using the 4 point foot mounting system in either a horizontal or vertical plane. b) It is very important that the winch be mounted on a flat surface so that the three sections (motor, cable drum and gear housing) are properly aligned. c) Before commencing installation, ensure the mounting facility being used is capable of withstanding the rated capacity of the winch. d) The fitment of winches and / or a frontal protection system may affect the triggering of SRS air bags. Check that the mounting system has been tested and approved for winch fitment in the air bag equipped vehicle. 2. Smittybilt manufactures winch mounting frames and / or Frontal Protection Systems to suit most popular vehicles. Winch frames are packaged with detailed instructions. 3. Should you wish to manufacture your own mounting plate the dimensions below will assist. A steel mount plate of 6mm thickness is recommended. Fasteners should be steel high tensile grade 5 or better. A poorly designed mount may void warranty. 4. The winch should be secured to the mounting with 3/8” UNC* 1-1/4” steel bolts and spring washers provided. 5. The roller fairlead is to be mounted so as to guide the rope onto the drum evenly. LUBRICATION INSTALLATION All moving parts in the winch are permanently lubricated with high temperature lithium grease at the time of assembly. Under normal conditions factory lubrication will suffice. Lubricate cable periodically using light penetrating oil. Inspect for broken strands and replace if necessary. If the cable becomes worn or damaged, it must be replaced. CABLE INSTALLATION Unwind the new cable by rolling it along the ground, to prevent kinking. Remove old cable and observe the manner in which it is attached to the drum flange. For Technical Support/Warranty Information please call 310-762-9944 Smittybilt, 400 West Artesia Blvd, Compton, CA 90220 Page 5 of 17 ELETRICAL CONNECTION For normal self-recovery work, your existing electrical system is adequate. A fully changed battery and proper connections are essential. Run the vehicle engine during winching operations to keep charged. Pay close attention to proper electrical cable connection as follows (refer to Diagram 1) Be sure to observe the following steps for a correct and safe electrical connection: 1. Short Red cable (B’) connecting to the red terminal (B) of winch motor. 2. Short black cable with yellow jacket (C’) connecting to the yellow terminal (C) of the motor. 3. Short black cable with black jacket (D’) connecting to the black terminal (D) of the motor. 4. Thin black cable (A’) connecting to bottom terminal (A) of the motor. 5. Long black cable (1.8m), one terminal (a) connecting to the bottom terminal (A) of the motor, and the other terminal negative (-) connecting to negative (-) terminal of battery. 6. Long red cable positive (+) connecting to positive (+) of battery. For Technical Support/Warranty Information please call 310-762-9944 Smittybilt, 400 West Artesia Blvd, Compton, CA 90220 Page 6 of 17 NOTE: 1. Your battery must be kept in good condition. 2. Be sure battery cables are not drawn taught across any surfaces, which could possibly damage them. 3. Corrosion on electrical connections will reduce performance or may cause a short. 4. Clean all connections especially in remote control switch and receptacle. 5. In salty environments use a silicone sealer to protect from corrosion. 6. Index the heads of the plate sutds into the keyhole slots on the back of the winch. 7. Attached the winch/Adaptor plate assembly to your trailer hitch, by inserting the trailer hitch ball through the shaped hole in the Adaptor plate. WINCH OPERATION SUGGESTION:The best way to get acquainted with how your winch operates is to make a few test runs before you actually need to use it. Plan your test in advance. Remember you can hear your winch as well as you can see it operate. Get to recognize the sound of a light steady pull, a heavy pull, and sounds caused by load jerking or shifting. Soon you will gain confidence in operating your winch and its use will become second nature to you. OPERATING: 1. Ensure the vehicle is secured by applying the parking brake or chocking the wheels. 2. Pull out the winch cable the desired length and connect to an anchor point. The winch clutch allows rapid uncoiling of the cable for hooking onto the load or anchor point. The shifter tab located on the gear housing of the winch operates the clutch as follows: a) To disengage the clutch, move the clutch shifter tab to the “OUT” position. Cable may be free spooled off the drum. b) To engage the clutch, move the clutch shifter tab into the “IN” position. The winch is now ready for pulling. 3. Recheck all cable rigging before proceeding. For Technical Support/Warranty Information please call 310-762-9944 Smittybilt, 400 West Artesia Blvd, Compton, CA 90220 Page 7 of 17 4. Plug in the winch hand control. It is recommended that the winching operation takes place from the driver’s position to ensure safe operation. 5. To commence winching operation, start vehicle engine, select in transmission, maintain engine speed at idle. 6. Operate the remote control switch to IN or OUT until the vehicle has been retrieved. Regularly check the winch to ensure cable is winding onto the drum evenly. Note: 1. Never winch with your vehicle in gear or in park, which would damage your vehicle’s transmission. 2. Never wrap the cable around the object and hook onto the cable itself, this can cause damage to the object being pulled, and kink or fray the cable. 3. Keep hands, clothing, hair and jewelry clear of the drum area and cable when winching. 4. Never use the winch if the cable is frayed, kinked or damaged. 5. Never allow anyone to stand near the cable, or in line with the cable behind the winch while it is under power, if the cable should slip or brake, it can suddenly whip back towards the winch, causing a hazard for anyone in the area. Always stand well to the side while winding. 6. Don’t leave the switch plugged in when winch is not in use. CHECK THE WINCH CAREFULLY AND THOROUGTLY BEFORE OPERATING! MAINTENANCE It is highly recommended that the winch be used regularly (once a month). Simply power the cable out 15m, free spool 5m and then power back in. This will keep all components in good working condition so that the winch can be relied on when needed. Contact your authorized outlet for technical assistance and repairs. SPARE PARTS: A comprehensive range of spare parts is available. For further information please contact Smittybilt Automotive Products. NOTE: The safety precautions and instructions discussed in this manual can’t cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors, which cannot be built into this product, but must be applied by the operator. For Technical Support/Warranty Information please call 310-762-9944 Smittybilt, 400 West Artesia Blvd, Compton, CA 90220 Page 8 of 17 XRC 8 Specifications Rated Line Pull: 8000Lbs (3600kgs) single-line Motor: 5.5hp /12V, Series Wound Control: Remote Switch, 12’ (3.7m) lead Gear Train: 3-Stage Planetary Gear Ratio: 172.8:1 Clutch: Rotating Ring Gear Brake: Automatic In-The-Drum Drum Size: (Diameter x Length) 2.5” x 8.82” (63.5mm x 224mm) Wire Rope: (Diameter x Length) 21/64” x 94’ (8.2mm x 28.5m) Fairlead: 4-Way Roller Remote Control: Included Recommended Battery: 650CCA Minimum for Winching Battery Leads: 25mm2 , 72” (1.8m) Finish: Black Weight: 94.0lbs (42.5Kgs) Mounting Bolt Pattern: 10.0” x 4.50” Line speed and amp draw (first layer) Lbs 2000 Line Pull NO LOAD Kgs 910 Fpm 37.2 18 Line Speed Mpm 11.4 5.5 Motor Current Amps 75 195 Line pull and cable capacity Layer of cable Lbs Rated line pull per layer Kgs Ft Cable capacity per layer Mpm 1 8000 3630 16 5 4000 1814 13.1 4.1 260 2 6900 3130 42 12 6000 2720 10.2 3.2 335 3 5850 2650 72 21 8000 3630 8.2 2.6 410 4 5100 2310 94 28 For Technical Support/Warranty Information please call 310-762-9944 Smittybilt, 400 West Artesia Blvd, Compton, CA 90220 Page 9 of 17 XRC 8 WINCH PARTS LIST No. 1 2 3 4 5 6 8 10 11 12 16 17 18 19 20 21 22 Parts No. 97281-01 97281-02 97281-03 97281-04 97281-05 97281-06 97281-08 97281-10 97281-11 97281-12 97281-16 97281-17 97281-18 97281-19 97281-20 97281-21 97281-22 Description Qty No. Sun Gear-Input 1 24 Gear Carrier-Input 1 25 Gear Carrier-Intermediate 1 26 Washer-1.2mm thickness 2 27 Gear Carrier-Output 1 28 Outer Spline 1 29 Drum 1 30 Brake System 1 32 Coupling Joint 1 36 Rotor 1 39 Motor End Cover 1 41 Carbon Frame & Brush Assy 1 45 Stator 1 46 Tie Rod Bolt 1 47 Motor Base 4 49 Nylon Bearing 1 50 Tie Rod 2 Part No. 97281-24 97281-25 97281-26 97281-27 97281-28 97281-29 97281-30 97281-32 97281-36 97281-39 97281-41 97281-45 97281-46 97281-47 97281-49 97281-50 97281 Description Qty Spring Washer 10 Gear Box Base 1 Gasket 1 Inner Gear 1 Clutch Gear 1 Gear Box Tube 1 Gasket 1 Gear Box End Cover 1 Bearing 1 Clutch Lever 1 Wire Rope 1 Winch Mount Bolt 1 Clevis Hook 4 Roller Fairlead 1 Control Box 1 Remote Control 1 1 For Technical Support/Warranty Information please call 310-762-9944 Smittybilt, 400 West Artesia Blvd, Compton, CA 90220 Page 10 of 17 XRC 10 Specifications Rated Line Pull: 1000Lbs (4535kgs) single-line Motor: 5.5hp/12V, Series Wound Control: Remote Switch, 12’ (3.7m) lead Gear Train: 3-Stage Planetary Gear Ratio: 218:1 Clutch: Rotating Ring Gear Brake: Automatic In-The-Drum Drum Size: (Diameter x Length) 2.5” x 8.82” (63.5mm x 224mm) Wire Rope: (Diameter x Length) 23/64” x 94’ (9.2mm x 28.5m) Fairlead: 4-Way Roller Remote Control: Included Recommended Battery: 650CCA Minimum for Winching Battery Leads: 25mm2 , 72” (1.8m) Finish: Black Weight: 99.0lbs (42.5Kgs) Mounting Bolt Pattern: 10.0” x 4.50” Line speed and amp draw (first layer) Lbs 2000 Line Pull NO LOAD Kgs 907 Fpm 29.53 14.44 Line Speed Mpm 9 4.4 Motor Current Amps 70 170 Line pull and cable capacity Layer of cable Lbs Rated line pull per layer Kgs Ft Cable capacity per layer Mpm 1 10000 4535 16 4.88 4000 1814 12.14 3.7 240 2 8633 3915 42 12.8 6000 2721 10.17 3.1 310 3 7716 3499 72 21.95 8000 3628 8.86 2.7 380 10000 4535 7.38 2.25 425 4 7089 3215 94 28.5 For Technical Support/Warranty Information please call 310-762-9944 Smittybilt, 400 West Artesia Blvd, Compton, CA 90220 Page 11 of 17 XRC XRC 10 WINCH PARTS LIST No. Parts No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 97210-01 97281-02 97210-03 97210-04 97210-05 97210-06 97210-07 97210-08 97210-09 97210-10 97210-11 97210-12 97210-13 97210-14 97210-15 97210-16 Gear Box End Cover Gasket Sun Gear-Input Inner Gear Gasket Outer Spline Gear Carrier-Input Gear Carrier-Intermediate Washer-1.2mm thickness Clutch Gear Gear Carrier-Output Gear Box Tube Clutch Handle Assy Outer Spline Link Screw Gear Box Base Qty No. Part No. Description 1 1 1 1 1 2 1 1 2 1 1 1 1 1 4 1 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 97281-24 97210-25 97210-26 97210-27 97210-28 97210-29 97210-30 97210-32 97210-36 97210-39 97210-41 97210-45 97210-46 97210-47 97210-49 Remote Control Control Box Assy Nylon Bearing Tie Rod Drum Brake System Coupling Joint Winch Mount Bolt Motor Base Rotor Stator Carbon Frame & Brush Assy Motor End Cover Roller Fairlead Clevis Hook Wire Rope For Technical Support/Warranty Information please call 310-762-9944 Smittybilt, 400 West Artesia Blvd, Compton, CA 90220 Page 12 of 17 Qty 1 1 2 2 1 1 1 4 1 1 1 1 1 4 1 1 XRC 12 Specification Rated Line Pull: 12000Lbs (5440kgs) single-line Motor: 6.6hp/12V, Series Wound Control: Remote Switch, 12’ (3.7m) lead Gear Train: 3-Stage Planetary Gear Ratio: 265:1 Clutch: Rotating Ring Gear Brake: Automatic In-The-Drum Drum Size: (Diameter x Length) 2.5” x 8.82” (63.5mm x 224mm) Wire Rope: (Diameter x Length) 23/64” x 94’ (9.2mm x 28.5m) Fairlead: 4-Way Roller Remote Control: Included Recommended Battery: 650CCA Minimum for Winching Battery Leads: 25mm2 , 72” (1.8m) Finish: Black Weight: 99.0lbs (45.0Kgs) Mounting Bolt Pattern: 10.0” x 4.50” Line speed and amp draw (first layer) Lbs 2000 Line Pull NO LOAD Kgs 907 Fpm 23.5 12.8 Line Speed Mpm 7.2 3.9 Motor Current Amps 65 120 Line pull and cable capacity Layer of cable Lbs Rated line pull per layer Kgs Ft Cable capacity per layer Mpm 1 120000 5440 16 5 4000 1814 10.5 3.2 165 6000 2722 9.4 2.9 215 8000 3629 7.4 2.3 270 2 10270 4654 42 12 3 9200 4169 72 21 4 8500 3852 94 28 10000 4532 6.3 1.9 320 12000 5440 5 1.5 370 For Technical Support/Warranty Information please call 310-762-9944 Smittybilt, 400 West Artesia Blvd, Compton, CA 90220 Page 13 of 17 XRC 12 WINCH PARTS LIST No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Parts No. 97212-01 97212-02 97212-03 97212-04 97212-05 97212-06 97212-07 97212-08 97212-09 97212-10 97212-11 97212-12 97212-13 97212-14 97212-15 97212-16 97212-17 97212-18 97212-19 97212-20 97212-21 97212-22 97212-23 97212-24 97212-25 Description Qty No. Washer 2 26 Sun Gear-Input 1 27 Gear Carrie-Input 1 28 Gear Carrier-Intermediate 1 29 Washer-1.2mm thickness 2 30 Gear Carrier-Output 1 31 Outer Spline 1 32 Spline Positioning Ring 1 33 Drum 1 34 Motor Long Bolt 1 35 Brake Assy 1 36 Coupling Joint 1 37 Rotor 1 38 Washer 2 39 Long Bolt 2 40 Motor End Cover 1 41 Carbon Assy 1 42 Stator 1 43 Link Srew 4 44 Motor Base 1 45 Nylon Bearing 2 46 Tie Bar 2 47 Bolt 9 48 Lock Washer 19 49 Gear Box Base 1 Part No. 97212-26 97212-27 97212-28 97212-29 97212-30 97212-31 97212-32 97212-33 97212-34 97212-35 97212-36 97212-37 97212-38 97212-39 97212-40 97212-41 97212-42 97212-43 97212-44 97212-45 97212-46 97212-47 97212-48 97212-49 Description Qty Gear Box Tube 1 Inner Gear 1 Inner Gear 1 Gasket 9500 3 Gear Box End Cover 1 Bolt 10 Brand 1 Shaft Sleeve 1 Clutch Spring 1 Washer 1 Washer 1 Clutch Steel Ball 1 Connection of Clutch Handle 1 Bolt 1 Wire Rope 1 Mount Nut 4 Lock Washer 4 Mounting Bolt 4 Clevis Hook 1 Roller Fairlead 1 Fairlead Mount Nut 1 Fairlead Mount Bolt 2 Control Box Assy 2 Handle Remote Control 1 1 For Technical Support/Warranty Information please call 310-762-9944 Smittybilt, 400 West Artesia Blvd, Compton, CA 90220 Page 14 of 17 For Technical Support/Warranty Information please call 310-762-9944 Smittybilt, 400 West Artesia Blvd, Compton, CA 90220 Page 15 of 17 Troubleshooting SYMPTOM POSSIBLE CAUSE Switch Assy not connected properly SUGGESTED REMEDY Insert Switch Assy firmly to the connector. Tighten units on cable connectors Loose battery cable Solenoid malfunctioning Tap solenoid to free contact, applying 12 volts to coil terminal directly. Motor does not turn on Defective Switch Assembly Makes an audible clicking when activating. Replace Switch Assy Defective Motor Water has entered motor Motor runs too hot Motor runs slowly or without normal power Check for voltage at armature port with switch pressed. If voltage is present, replace motor. Drain and dry. Run in short bursts without load until completely dry. Long period of operation Let winch cool down periodically. Battery runs down Insufficient current or voltage Recharge battery by running vehicle’s engine. Clean, tighten or replace the connector. Motor runs but cable drum Clutch not engaged does not turn Ensure lever is completely in “engaged” position. If that does not work, contact qualified technician to check and repair. Motor runs direction only Tap solenoid to free contacts. Repair or replace solenoid, Replace Switch Assy in one Defective or stuck solenoid Defective Switch Assy For Technical Support/Warranty Information please call 310-762-9944 Smittybilt, 400 West Artesia Blvd, Compton, CA 90220 Page 16 of 17 Warranty Limited 2 Year Warranty Smittybilt, Inc. offers a limited two (2) year warranty (to the original retail purchaser) fro each new Smittybilt consumer/RV electric winch against manufacturing defects in workmanship and materials on all the mechanical components. Electrical components consisting of motors, solenoids, wiring, wire connectors and associated parts have a limited one (1) year warranty. New cable assemblies are warranted against defects in workmanship and materials when received by the retail purchaser. There is no applicable warranty after initial use. Warranty registration cards for each winch must be submitted at the time of purchase or within 30 days by the end user. Warranty will only be valid for the original purchaser of the winch and installed on the vehicle for which it was originally registered. Smittybilt electric winches are intended for recreational self-recovery usage. The warranty is void if the winch is used in commercial/industrial applications. The obligation under this warranty, statutory or otherwise, is limited to the replacement or repair at the manufacturer’s factory, or at a point designated by the manufacturers, of such part(s) as shall appear to the manufacturer, upon inspection of such part(s) as shall appear to the manufacturer, upon inspection of such part(s), to have been defective in material of workmanship. This warranty does not obligate Smittybilt,Inc. to bear the cost of labor or transportation charges in connection with the replacement or repair of defective parts, nor shall it apply to a product upon which repairs or alterations have been made, unless authorized by the manufacturer, or for equipment misused, neglected or improperly installed. IMPORTANT NOTICE To the fullest extent permitted by applicable law, the following are hereby excluded and disclaimed: 1) All warranties of fitness for a particular purpose; 2) All warranties of merchantability; 3) All claims for consequential or incidental damages. There are no warranties that extend beyond the description that appears on the face hereof. Some states do not allow the above exclusions or disclaimers in consumer transactions and as such this disclaimer/exclusion may not apply to you. To the extent such warranties of fitness or merchantability are deemed to apply to this product, they exist for only so long as the express limited warranty elsewhere set forth is in existence. Smittybilt, Inc. reserves the right to change, alter or improve its products in design, materials or appearance without incurring any obligation to incorporate such changes in products that were previously manufactured. This Warranty gives you specific legal rights and you may have other legal rights, which vary from state to state. To submit a warranty claim contact: Smittybilt 1-8888-717-5795 400 West Artesia Blvd Compton, CA 90220 For Technical Support/Warranty Information please call 310-762-9944 Smittybilt, 400 West Artesia Blvd, Compton, CA 90220 Page 17 of 17 Warranty Information Card First name: Last name: Age: Sex: Marital Status: Level of Education: City/Province: Zip/Postal Code: Country: Telephone Number: Email Address: Which Smittybilt winch did you purchase? Model Number: Date of Purchase: Where did you purchase this product? Store or catalog name: Store Location: How satisfied were you with the dealer and/or sales staff? Who installed or will install your Smittybilt product? Is this the first time you have purchase a winch? If no, what brand have you brought before? What type of vehicle will this Smittybilt winch be installed on? Year: Make: Model: 2WD: 4WD: What is the vehicles main use? What other accessories have you purchased for your vehicle? For Technical Support/Warranty Information please call 310-762-9944 Smittybilt, 400 West Artesia Blvd, Compton, CA 90220 Page 18 of 17
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 17 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : 74611fae-4d27-11de-0000-4fb9d1e5b2b1 Producer : GPL Ghostscript 8.61 Modify Date : 2009:05:27 07:37:06-07:00 Create Date : 2009:05:27 07:37:06-07:00 Creator Tool : PDFCreator Version 0.9.5 Document ID : 74611fae-4d27-11de-0000-4fb9d1e5b2b1 Format : application/pdf Title : XRC8 10 12 Instructions Creator : mwesthoff Author : mwesthoff Subject :EXIF Metadata provided by EXIF.tools