Sony Ericsson K750i, K750c Installation Instruction, Electrical. Www.s Manuals.com. K750 Electrical
User Manual: Sony Ericsson K750c, K750i - Service manuals and Schematics, Disassembly / Assembly. Free.
Open the PDF directly: View PDF 
.
Page Count: 10
Installation Instruction, Electrical
1/00021-2/FEA 209 544/94 B
Company Internal
©
Sony Ericsson Mobile Communications AB
1(9)
Installation Instruction, Electrical
Applicable for K750i / K750c
Contents
1
General.............................................................................................................................2
2
Go/No Go Testing............................................................................................................2
2.1
Test Set-up Go/No Go test ................................................................................2
2.2
Test Set..............................................................................................................3
2.3
RF Connections Antenna Coupler.....................................................................3
2.4
RF Connections Antenna adapter (optional) .....................................................3
3
Calibration.......................................................................................................................4
3.1
Test set up – SERP (only authorized centers) ...................................................4
3.2
Test Set..............................................................................................................5
3.3
Power Supply.....................................................................................................5
3.4
Battery eliminator..............................................................................................5
3.5
GPIB card and cable..........................................................................................5
3.6
RF Connection...................................................................................................5
3.7
SonyEricsson programming interface – SEPI ...................................................5
3.8
SonyEricsson programming interface cable......................................................5
3.9
USB PC cable....................................................................................................5
4
General Equipment.........................................................................................................6
4.1
Test Set up.........................................................................................................6
4.2
Computer...........................................................................................................7
4.3
Service Card Reader and Service Card..............................................................7
4.4
SonyEricsson programming interface – DCU-60..............................................7
4.5
Label Printer (optional) .....................................................................................7
4.6
Infrared Device..................................................................................................7
4.7
Bluetooth Device...............................................................................................7
5
Software...........................................................................................................................8
5.1
EMMA III..........................................................................................................8
5.2
Labelmake II software (optional) ......................................................................8
5.3
Go/No Go script ................................................................................................8
5.4
SERP (only authorized centers).........................................................................8
6
Revision History..............................................................................................................9
Installation Instruction, Electrical
1/00021-2/FEA 209 544/94 B
Company Internal
©
Sony Ericsson Mobile Communications AB
2(9)
1 General
The Electrical Installation Instructions describes the procedures for installing all of the
hardware and software needed to perform testing, calibration, software loading and repair
activities at an Electrical level for the Sony Ericsson products specified.
NOTE! This product is manufactured with lead-free solder and lead-free components.
During electrical repair, it is critical to make sure that no lead is introduced into the product.
For this reason, certain repair materials and equipment must be designated as lead-free and
labelled accordingly. A lead-free work area must be setup that is completely separated from
work areas that are used to make leaded repairs. Certain items must be designated for lead-
free work only. Some of the items that need to be clearly labelled in this way are listed in the
Equipment List Electrical. Note that any item that contacts the solder must be labelled and
used for lead-free work only.
2 Go/No Go Testing
There are two options for performing a Go No/Go test. One is to use an RF Fixture and the
other is to use an antenna coupler together with a shielding box.
2.1 Test Set-up Go/No Go test
All test hardware necessary for this test set up is documented in the Electrical Equipment List.
Installation Instruction, Electrical
1/00021-2/FEA 209 544/94 B
Company Internal
©
Sony Ericsson Mobile Communications AB
3(9)
2.2 Test Set
An E-GSM 900/GSM 1800/GSM 1900 Test Set approved according to the Instrument List
must be used.
It should be installed according to the Instrument Manufacturer Instructions.
2.3 RF Connections Antenna Coupler
Connect the RF Cable between the RF-port of the Test set and the RF Shield box. The
Antenna Coupler should be installed into the RF Shield Box according to manufacturer
instructions.
2.4 RF Connections Antenna adapter (optional)
Connect the RF-cable between the RF-port of the Test set and the Antenna adapter. Assemble
the RF adapter to the RF-holder according to the information in the Test Instruction
Electrical.
Installation Instruction, Electrical
1/00021-2/FEA 209 544/94 B
Company Internal
©
Sony Ericsson Mobile Communications AB
4(9)
3 Calibration
3.1 Test set up – SERP (only authorized centers)
All test hardware necessary for this test set up is documented in the Electrical Equipment and
Instrument List.
Installation Instruction, Electrical
1/00021-2/FEA 209 544/94 B
Company Internal
©
Sony Ericsson Mobile Communications AB
5(9)
3.2 Test Set
A Test Set approved according to the Instrument List must be used.
It should be installed according to the Instrument Manufacturer Instructions.
3.3 Power Supply
Power Supply according to Instrument List must be used.
3.4 Battery eliminator
Battery eliminator is to be used together with a power supply to power the phone during the
calibration. Connect the cables from the battery eliminator to the power supply, red cable to
positive output terminal and black cable to negative output terminal.
3.5 GPIB card and cable
GPIB card and cable according to the Equipment List. Use the GPIB cable to connect the
GPIB card to the test instrument.
3.6 RF Connection
RF-holder and RF adapter according to Equipment List. Connect the RF adapter to the RF
cable. The RF adapter is held on the phone with the RF fixture.
3.7 SonyEricsson programming interface – SEPI
The USB programming interface is delivered with the necessary software and instruction for
installation. The USB programming interface (SEPI) should be connected to an USB-port on
the computer.
3.8 SonyEricsson programming interface cable
The cable is the interface between the USB programming interface (SEPI) and the phone.
3.9 USB PC cable
The A-B Plug-Plug cable is the interface between the computer and the USB programming
interface (SEPI). Connect the cable between the USB programming interface and the
computer.
Installation Instruction, Electrical
1/00021-2/FEA 209 544/94 B
Company Internal
©
Sony Ericsson Mobile Communications AB
6(9)
4 General Equipment
4.1 Test Set up
General Test set up to perform SW loading and manual test according to Test Instruction. All
necessary hardware for this test set up is documented in the Electrical Equipment list.
Installation Instruction, Electrical
1/00021-2/FEA 209 544/94 B
Company Internal
©
Sony Ericsson Mobile Communications AB
7(9)
4.2 Computer
IBM compatible computer is required. The computer should include at least two USB-ports.
Refer to Equipment List for minimum requirements.
4.3 Service Card Reader and Service Card
The Service Card Reader is delivered with the necessary software and instructions for
installation. The Service Card Reader should be connected to an USB-port on the computer.
4.4 SonyEricsson programming interface – DCU-60
The cable is the interface between the computer and the phone. DCU-60 cable should be
connected to an USB-port on the computer.
4.5 Label Printer (optional)
A Zebra printer model 90xi, 90xiII or 4000 deluxe shall be used. Connect the printer with a
standard RS 232 serial printer cable [refer to the Zebra printer manual] to the serial port on
the computer. Read the Zebra installation manual for more information about the installation.
4.6 Infrared Device
RS 232 or USB type infrared adapter may be used. Install according to the manufactures
instructions.
4.7 Bluetooth Device
Any Bluetooth device as headset, other Bluetooth phone or other Bluetooth device can be
used to verify the Bluetooth function in the phone. Set up the connection according to the
chosen equipments manufacturer.
Installation Instruction, Electrical
1/00021-2/FEA 209 544/94 B
Company Internal
©
Sony Ericsson Mobile Communications AB
8(9)
5 Software
5.1 EMMA III
EMMA III contains all software required to service the product. Installation and user manuals
are available in the EMMA III start page.
http://ma3.extranet.sonyericsson.com/ma3/
5.2 Labelmake II software (optional)
LabelMake II is an application installed through Java Web Start.
Access the Labelmake software from CSPN Web page.
You will find LabelMake II in the dropdown menu on the CSPN web page.
http://cspn.extranet.sonyericsson.com
Press “START LabelMake II “button and you will be directed to the LABELMAKE II client
page.
Product labels are downloaded on-line from a remote server database.
5.3 Go/No Go script
An approved Sony Ericsson Test Script must be installed in the Test Instrument. The script
can be downloaded from CSPN. The Test Script is located on CSPN under Repair
Instructions / Standard.
http://cspn.extranet.sonyericsson.com
Install the script according to the Instrument Manufacture’s Instruction.
5.4 SERP (only authorized centers)
Download the latest revision of SERP application from CSPN. This application is located
under Repair Instructions/Standard/SERP Install package
http://cspn.extranet.sonyericsson.com
Unzip the file and open the Installation instructions.
Follow the Install instructions to install SERP.
Installation Instruction, Electrical
1/00021-2/FEA 209 544/94 B
Company Internal
©
Sony Ericsson Mobile Communications AB
9(9)
6 Revision History
Rev. Date Changes / Comments
A 2005-05-13 Initial release
B 2005-05-19 Updated information about Labelmake II
