TimeQplus User Guide_Rev C Time Qplus TQ600 Tqplus Guide En

User Manual: timeQplus TQ600

Open the PDF directly: View PDF .
Page Count: 89

timeQplus User Guide

Publication: 06-0414-000

Date of Publication: Sept. 12, 2013

Revision: C

06-0414-000 Rev. C

Contacting Acroprint

When contacting customer support, please have your product CD and registration information available.

Mailing Address:

Acroprint Time Recorder Company, Inc

timeQplus Support

5640 Departure Drive

Raleigh, North Carolina 27616

Phone:

Toll Free: (800) 334-7190

Web/Internet:

Email: supportdept@acroprint.com

Website: http://www.acroprint.com

iii

06-0414-000 Rev. C

Table of Contents

Welcome ..........................................................................................................................1

Getting Started................................................................................................................2

Before Getting Started................................................................................................................3

timeQplus Setup Wizard.............................................................................................................4

timeQplus Administrator Functions.............................................................................. 5

timeQplus Navigation Bar ..........................................................................................................6

Employees ...................................................................................................................................7

Managing Employees.................................................................................................................7

Employee Options......................................................................................................................9

Employee Finger/Face/Hand Enrollment ...................................................................................9

Removing Employee Finger/Face/Hand Templates ................................................................10

Messages ...................................................................................................................................11

Setup ..........................................................................................................................................12

General.....................................................................................................................................12

Holidays....................................................................................................................................14

Work Codes..............................................................................................................................14

Shifts ..........................................................................................................................................16

Shift Settings ............................................................................................................................16

Lunch Rules .............................................................................................................................20

Overtime...................................................................................................................................22

7th Day Overtime .....................................................................................................................23

Holidays....................................................................................................................................23

Salaried Shift Settings..............................................................................................................24

Punch Editing ............................................................................................................................25

Managing Transactions............................................................................................................26

Editing Total Time Accumulations............................................................................................27

Printing Time Cards..................................................................................................................28

Reports.......................................................................................................................................29

Generating a Report.................................................................................................................29

Future Transactions Report......................................................................................................30

Export.........................................................................................................................................31

Exporting Time and Attendance Data ......................................................................................31

Unapproved Timecards............................................................................................................32

Advanced Payroll Integration ...................................................................................................32

File Payroll Export Formats......................................................................................................32

Custom Export File Builder.......................................................................................................33

QuickBooks® Payroll Integration .............................................................................................37

Peachtree Complete Accounting..............................................................................................39

WellsFargo, Premier, QwikPay and Intuit PC Access Import File............................................41

06-0414-000 Rev. C

ADP Version 7.0.......................................................................................................................41

Generic V2.0 ............................................................................................................................42

Generic ASCII file Export .........................................................................................................43

Genesys & Oryel Payroll Export...............................................................................................43

PayChex Paylink Export...........................................................................................................45

PayChex Preview Export..........................................................................................................45

PayChex IM0007 Import File....................................................................................................46

PrimePay PrimeLink Export .....................................................................................................46

Heartland Plus One Fixed Length File .....................................................................................47

Supervisors................................................................................................................................48

Managing Administrators and Supervisors ..............................................................................48

Supervisor Preferences............................................................................................................50

Time Clock .................................................................................................................................51

Adding an Ethernet Connected Time Clock.............................................................................52

Adding a Serial Connected Time Clock ...................................................................................55

Adding a USB Flash Drive Time Clock ....................................................................................57

Assigning/Removing Employees to/from Time Clocks ............................................................57

Loading Employee Data onto a USB Time Clock ....................................................................58

Uploading Punch Data from the USB flash drive to the timeQplus server...............................59

Poll and Update........................................................................................................................60

Changing Time Clock Connection Types.................................................................................61

Copying Multiple Finger Templates from One Time Clock to Another.....................................63

Hand Punch ...............................................................................................................................64

System Utilities..........................................................................................................................65

Date Tools ................................................................................................................................65

timeQplus Settings ...................................................................................................................67

timeQplus Supervisor Functions ................................................................................68

timeQplus Navigation Bar ........................................................................................................69

Employees .................................................................................................................................70

Work Codes..............................................................................................................................71

Messages ...................................................................................................................................74

Punch Editing ............................................................................................................................75

Reports.......................................................................................................................................75

Time Clock .................................................................................................................................76

Virtual Clock..................................................................................................................77

Login to Virtual Clock...............................................................................................................78

Submit Employee Time Slip.....................................................................................................79

IN/OUT Board.............................................................................................................................80

Glossary.........................................................................................................................81

06-0414-000 Rev. C

Welcome

The timeQplus system allows a company's time & attendance to be managed from a single Windows-

based PC.

Key Time and Attendance Features:

• Easily review employees’ time totals past and present

• Edit Time Sheets

• Save and print reports

• Export data to various file formats and payroll programs

• Create Work Codes and assign to employees

• Report on Archived Pay Periods

• Submit Single Punch or Multiple Punches (TimeSlips)

• Submit Future Transactions using TimeSlips Feature

06-0414-000 Rev. C

Getting Started

This chapter provides information on how to get started with timeQplus. It contains the following

sections:

¾ Before Getting Started

¾ timeQplus Setup Wizard

Getting Started

06-0414-000 Rev. C

Before Getting Started

Before using timeQplus for the first time, you may find it helpful to have your company’s pay period and

time and attendance policies handy.

Here is a list of configuration settings you will review and modify as needed:

1. Adjust the following items located in the Setup section as desired:

• Current Pay Period Start Date

• Pay Period Length

• Pay Period Start Date

• Holiday pay policies

• Time card approval policies

• Date Format

• Time Totals Format

2. For each shift used, adjust the following items located in the Shifts and Lunches section as

desired:

• Set up shift rules

• Maximum Time on the Clock

• Pay Interval Rounding

• Day Change Offset

• Overtime Thresholds

• 7

th Day Overtime

• Set up lunch rules

3. Add Employees to the timeQplus System.

4. Add Supervisors to the timeQplus System and then assign employees to those Supervisors.

After completing the Setup Wizard, we recommend launching the timeQplus software and generating a

Rules Setup Report (click Reports on the navigation bar, then select Rules Setup). Preview or print this

report to verify the application has been configured correctly to reflect your company’s time and

attendance policies.

After checking this report for accuracy and (if necessary) making any desired changes, you may begin

adding employees.

Notes:

• Most settings can be changed at any time and will affect only the total time accumulations in the

Previous and Current Pay Period.

• Changes to the next pay period start date will lengthen or shorten the duration of the current pay

period, but not affect the Previous Pay Period.

Getting Started

06-0414-000 Rev. C

timeQplus Setup Wizard

The first time you launch timeQplus, the system will open the timeQplus Setup Wizard. This wizard will

walk you through a setup procedure to establish the initial settings for your timeQplus system. The

application is configured with default settings, however, if you choose, you can simply click through the

initial pay period setup, add employees and start clocking IN and OUT. However, we strongly suggest

updating these default settings as needed to conform to your company’s policies.

If you are upgrading from a previous version of either Attendance Rx Version 2 or timeQplus Version 3

you must still go through the Setup wizard, but simply press the Enter key for each input. Your existing

settings will later be automatically imported from your existing database.

For new installations, before you proceed through the Setup Wizard, you may find it helpful to review the

Before Getting Started section.

At any time during the Setup Wizard, you can use the Back button to review or change previous settings.

When you have entered all your company’s information, click the Finish button to complete the process

and start timeQplus.

Note: Each of these settings can be changed at any time during normal operation using the Setup and

Shifts screens on the timeQplus Navigation Bar. If you cancel the wizard before completing the setup,

timeQplus will automatically run the Setup Wizard again the next time the software is started.

06-0414-000 Rev. C

timeQplus Administrator Functions

timeQplus has two level of system access:

1. Administrator – has total access to all system functions and data.

2. Supervisor – has limited access with the ability to view/edit employee information (including time

cards) and run reports for assigned employees only.

This chapter provides detailed information on timeQplus functions specific to the administrator role. It

contains the following sections:

¾ timeQplus Navigation Bar

¾ Employees

¾ Messages

¾ Setup

¾ Shifts

¾ Punch Editing

¾ Reports

¾ Export

¾ Supervisors

¾ Time Clock

¾ System Utilities

timeQplus Administrator Functions - Navigation Bar

06-0414-000 Rev. C

timeQplus Navigation Bar

The timeQplus Navigation Bar allows an administrator to manage the timeQplus software. An

administrator can update any configuration settings, add and delete employees, approve time cards and

TimeSlips, export timeQplus data to payroll, and view/print reports.

To see the Navigation Bar, double click the timeQplus icon on your desktop. Ensure that you are

connecting to the correct server and then enter your Administrator Login and Password.

Click the buttons on the left Navigation bar to access these Administrator functions:

• Employees Manage employee information and shift assignments

• Messages View and edit your Company and Employee messages

• Setup Setup company pay rules, Holidays, and Work Codes

• Shifts Define shift hours, lunch rules, overtime, and holiday pay

• Punch Editing View and edit employee Time Cards & Time Slips

• Reports Print or preview reports

• Export Export time cards to payroll or a service provider

• Supervisors Manage administrators and supervisors

• Time Clock Manage time clock devices

• Hand Punch Manage hand punch devices

timeQplus Administrator Functions - Employees

06-0414-000 Rev. C

Employees

The Employees screen allows an administrator to enter and view all employees and their information. An

administrator can add a new employee, delete or modify an existing employee, assign employees to Time

Clocks, or assign Work Codes to employees (please reference the Work Codes section in the timeQplus

Supervisor Functions chapter for more information). An administrator can also enroll finger, face, and/or

hand templates after capturing the templates on an appropriate Time Clock.

To access the Employees screen, click the Employees button on the left Navigation Bar or click View on

the top menu and choose Employees.

Managing Employees

To Add an Employee:

• On the Employees screen, type the new employee information into the top blank row,

entering the employee's Lastname, Firstname, MI (optional), Badge (optional), UserID,

employee Number (optional), Shift, and Hire Date.

o Note: If you wish, employee UserIDs and Numbers can be set to auto-increment

by adjusting the Employee Options located on the top menu bar under ‘File’.

• Press ENTER to save the new employee information and automatically create another blank

line at the top for additional employee entries.

• To erase input information before adding a new employee, press the ESC key on your

keyboard, or click the Refresh button on this screen.

If employees will be using proximity/barcode/magstripe badge Time Clocks to

punch, ensure the Badge field corresponds with the number on the actual badge

assigned to the employee on the Time Clock. Refer to the TQ600 User Manual for

more information.

If employees will be using biometric finger reader or facial recognition Time

Clocks to punch, make a note of the UserID assigned to each employee. It may be a

good idea to print the Employee Profiles report, which lists each employee’s UserID,

which will be used to enroll the employee’s finger/face on the time clock. Refer to the

TQ600 User Manual for more information on capturing finger/face templates.

timeQplus Administrator Functions - Employees

06-0414-000 Rev. C

To Edit an Employee:

• From the Employees screen – On the Employees screen, simply type the updated

information directly into the appropriate field and press ENTER.

• From the Employee Profile screen – Click anywhere on the row containing the employee to

be edited. Click the Detail button at bottom right to launch the Employee Profile window.

This screen allows additional employee information to be recorded and saved. The

Password field must be populated with the password the employee will be using to punch at

the Virtual Clock and/or a connected Time Clock. There are also ten custom fields that can

be used for creating Custom Payroll Exports. You can update the employee’s information and

then click Save. Click Cancel to return to the Employees screen without saving.

To Delete an Employee:

• Click the Employees button on the left Navigation Bar or click View on the top menu bar and

choose Employees.

• Click anywhere on the row containing the employee to be deleted.

• Click the Delete button at lower right.

Note: You will not be able to delete an employee who has punches in the current or previous

pay periods. The employee will be marked for deletion (shown with a red line through the

row), and will be automatically deleted when the employee no longer has active punches in

the current or previous pay periods.)

• Click Yes to confirm the deletion, or click No to cancel.

timeQplus Administrator Functions - Employees

06-0414-000 Rev. C

Employee Options

The Employee Options feature allows an administrator to determine the format of time totals viewed by

employees using the Virtual Clock. Time can be displayed in either minutes or hundredths. Employee

Options also allows employee UserIDs and Numbers to be auto incremented when adding new

employees to timeQplus.

To Change Employee Options:

• Click File on the top menu bar and choose Employee Options.

• Select your preference for Time Totals Format. You may choose to display time totals in minutes

or hundredths.

• To have the software automatically increment new employee UserIDs, check the Auto Increment

New Employee UserIDs box.

• To have the software automatically increment new employee Numbers, check the Auto Increment

New Employee Numbers box.

• Click Ok when done. To exit without saving changes, click Cancel.

Employee Finger/Face/Hand Enrollment

Collecting, enrolling, and assigning an employee’s Finger, Face, or Hand on a Time Clock is a three

step process.

1. Collect the employee’s Finger/Face/Hand template on the Time Clock.

• You will need to know the User ID assigned to the employee in timeQplus. You may find

it helpful to print an Employee Profiles report to ensure you record the templates with

the correct USER ID.

• For detailed instructions, refer to the TQ600 User Manual for finger templates, the

TQ600F User Manual for face templates, and the Hand Punch User Manual for hand

templates. These documents can be found under Documentation on the top menu bar.

• For USB Flash Drive time clocks, after all employees are enrolled, insert a USB flash

drive into the clock to capture finger or face templates.

 On the TQ600B (finger), press Menu > PenDrive Mng > Download User.

 On the TQ600F (face), press Menu > Dn/Upload > Download User.

2. Associate the template with the employee record in the software.

• On the Employees screen, select the row containing the employee’s name.

• Click the appropriate Enroll or Remove button and follow the on-screen instructions.

3. Assign the employee to additional Time Clocks.

• On the Time Clock screen, select the Time Clock the employee will be using to punch.

If using a hand punch, click the Hand Punch tab and select the appropriate time clock.

timeQplus Administrator Functions - Employees

06-0414-000 Rev. C

• Select the employee’s name in the Unassigned Employees list and click the right-

pointing arrow button to move that employee’s name to the Assigned Employees list.

Click the Save button to save the assignment.

Note: Employees can be assigned to and are able to punch at multiple Time Clocks.

Removing Employee Finger/Face/Hand Templates

1. On the Employees screen, select the row containing the employee’s name.

2. Click the appropriate Enroll or Remove button for the template you wish to delete and follow

the on screen instructions.

Note: Once an employee’s template has been removed from timeQplus, it will remain on all time clocks

to which the employee was assigned until after the next scheduled/manual poll or update occurs. Please

see the Time Clocks section, Poll and Update for more information.

timeQplus Administrator Functions - Messages

06-0414-000 Rev. C

Messages

The Messages screen allows an administrator to display a company-wide or employee-specific message

to employees when they punch at a PC on the Virtual Clock.

Note: Messages will only appear on the Virtual Clock screen when an

employee punches. Messages will not display on connected Time Clocks.

To create or edit a company-wide message:

• To access the Messages screen, click the Messages button on the left Navigation Bar or click

View on the top menu and choose Messages.

• Enter a company-wide message in the Enter a Company Message field. This message will

appear on the PC screen after each employee punches at the PC.

• Click the Save button to save the message or click the X button to delete the Company Message.

Note: You must delete the Company Message when you no longer wish it to display. It will continue to

display on the PC screen after each employee punch as long as it exists on this screen.

To create or edit employee-specific messages:

Enter employee-specific messages in the Message field next to the employee’s name. This message will

appear once on this employee’s PC screen after the next punch.

timeQplus Administrator Functions - Setup

06-0414-000 Rev. C

Setup

The Setup screen allows an administrator to adjust variables related to the clock, time calculations, pay

periods, holidays and Work Codes. Most items can be changed at any time and the change will be

reflected in the total time accumulations for the current and previous pay periods only.

To access the Setup screen, click the Setup button on the left Navigation Bar or click View on the top

menu bar and choose Setup. Three tabs are available for editing: General, Holidays, and Work Codes.

General

The following items may be edited using the General tab:

• Pay Period – timeQplus supports WEEKLY, BI-WEEKLY, SEMI-MONTHLY, and MONTHLY Pay

Periods.

• Time Card Approvals – timeQplus can be configured to require that timecards be approved by a

supervisor (or an administrator) before they can be exported to payroll.

timeQplus Administrator Functions - Setup

06-0414-000 Rev. C

To Change the Pay Period Length:

Be aware that pay periods are a critical part of time and attendance tracking.

Changing pay periods can have legal and personnel implications. Exercise

caution when changing the pay period after the timeQplus software has been

configured and is in use.

1. Click the Modify button in the Pay Period section of the General tab. This will open the Modify

Active Pay Periods screen.

The available choices are:

o Weekly - Employees are paid once per week

o Bi-weekly - Employees are paid every two weeks

o Semi-Monthly - Employees are paid twice per month

o Monthly - Employees are paid once per month

2. Change the Next Pay Period Start Date if necessary to reflect the new pay period starting date.

You may either click the downward-facing arrow at the right of the field to open a calendar from

which you can select the desired date, or you may simply type the desired date directly in the

Next Pay Period Start Date field.

3. Click the Modify button to save your changes. To exit without saving changes, click the Cancel

button.

timeQplus Administrator Functions - Setup

06-0414-000 Rev. C

To configure Time Card Approvals preferences:

• Check the “Do not export unapproved Time Cards for Hourly Employees” box to prevent the

export of unapproved time cards for hourly employees.

• Check the “Do not export unapproved Time Cards for Salaried Employees” box to prevent the

export of unapproved time cards for salaried employees.

• Click the Save button when done. To quit without saving changes, select another option from the

left Navigation Bar or click the Refresh button at top right and then click No in the Save Changes

dialog box.

Holidays

Optionally, timeQplus can track paid holidays and include this information when exporting to payroll. The

timeQplus software does not automatically calculate holiday dates; they will need to be manually entered

each year. If your company requires that an employee work a certain number of days before becoming

eligible for paid holidays, this can also be configured on this screen.

The following items may be edited using the Holidays tab:

• Holiday Dates - Enter the date or select a date from the popup calendar. Enter the name of the

holiday and press Enter to save. Repeat to add additional holidays.

To delete a holiday, click to highlight the holiday you want to remove, and then click the Delete

button.

• Employee Eligibility for Holidays - In the ‘Eligible for Holiday Pay’ box, enter the number of

days a new employee must work before becoming eligible for Holiday Pay and then click Save.

To quit without saving changes, select another option from the left Navigation Bar or click the

Refresh button at top right and then click No in the Save Changes dialog box.

Work Codes

Work Codes are used to allow a company to calculate how an employee’s work time is applied to a

specific department, project, task, etc. Work codes can be entered, edited or deleted using the Work

Codes tab on the Setup Screen. This list is referred to as the Master List of Work Codes. timeQplus can

be configured to include work code information when exporting punch data to payroll.

The following items may be edited using the Work Codes tab:

• Code – the work code number. After entering the first code number, timeQplus will auto increase

the next work code number by 1. You may choose to keep the new number or just type over to

input another of your choice.

• Name – the work code name.

timeQplus Administrator Functions - Setup

06-0414-000 Rev. C

• Description – a description of the work code; optional but can be very useful.

• Write to Time Clock – Must be checked before the work code can be assigned to employees or

used on any Time Clock (including the Virtual Clock).

The following applies to Hourly employees only:

• A Work Code must have "Write to Time Clock" set before it can be assigned to employees and

used on any Time Clock, including the Virtual Clock.

• Work Code assignments are managed on the Employees screen. Please see the Work Codes

section in the timeQplus Supervisor Functions chapter for detailed instructions.

• Work Codes can be used on TQ600 Time Clocks (Facial, Biometric, Proximity, Barcode, and

Magstripe), and on the Virtual Clock.

• There are two modes for using Work Codes on connected Time Clocks (the Virtual Time Clock

handles Work Codes a bit differently). Consult the user manual for details on setting the

mode on each Time Clock.

o Mode 3 - A Time Clock configured to Mode3 will allow employees to choose only their

assigned Work Codes stored in that Time Clock.

o Mode 4 - A Time Clock configured to Mode 4 will allow any employee to choose any

Work Code that has been stored in that Time Clock.

• Because the Virtual Clock is controlled entirely by the timeQplus software, it reacts differently to

Work Codes:

o If an employee is assigned Work Codes, then only those Work Codes are available to

choose when punching.

o If an employee has no Work Codes assigned, then all Work Codes with ‘Write on Time

Clock’ checked will be available for use when punching.

• A punch is considered a ‘Transfer’ if a Work Code different from the previous punch is selected.

• All OUT punches will have the same Work Code as the previous punch, which could be either an

IN or a TRANSFER.

The following applies to Salaried Employees only:

• To assign a salaried employee a work code, select the employee on the Punch Editing screen.

• In the Transaction area, select the date.

• Select ‘Reg’ from the Type drop down list and enter the time [HH:MM].

• Select a work code from the Work Code drop down list and click Insert to save changes.

timeQplus Administrator Functions - Shifts

06-0414-000 Rev. C

Shifts

A shift can be defined as a set of rules enforcing company policy for a group of employees, related to

start and stop times, lunch times, overtime, and holidays. When an employee is assigned to a shift, the

software then refers to the set of rules defined for that shift and applies those rules to that employee's

transactions in order to derive the total time accumulations.

Up to twelve different shifts can be defined in timeQplus. A shift can be a traditional shift, a department, a

group within a department, etc. Each shift may be defined differently with its own set of rules.

To access the Shifts screen, click the Shifts button on the left Navigation Bar or click View on the top

menu bar and choose Shifts. The Shifts screen consists of four tabs: Shift Settings, Lunch Rules,

Overtime, and Holidays.

Shift Settings

Under the Shift Settings tab, the following items may be edited: Pay Interval Round, Max Time on

Clock, Day Change Offset, Shift Start, Shift Stop, Round, Grace, and Dock. Each setting is described

in the sections that follow. Note: Definitions for all these settings can be found in the Glossary.

To edit a shift’s settings:

• Select a shift to edit from the Select a Shift drop-down list.

• To change the name of a shift, simply type the new name in the Shift Name field.

• Click the Shift Settings tab to modify Pay Interval Round, Max Time on Clock, and Day Change

Offset. Check the Shift Rules Enabled box to modify Shift Start, Shift Stop, Round, Grace and Dock

values. Click the Save button when finished. If you do not wish to make use of the Round, Grace or

Dock features, leave the minutes set to zero.

Pay Interval Rounding

Pay Interval Rounding causes time worked totals for each employee to be rounded to the nearest one,

five, six, ten or fifteen minute increment. It will not affect the actual punch time recorded in the software,

only the worked time totals. If you do not wish for your worked time totals to be rounded, set the Pay

Interval Rounding value to one minute (this is the default).

timeQplus Administrator Functions - Shifts

06-0414-000 Rev. C

Example 1:

Pay Interval Round time set to 10 minutes.

• Punch at 10:14 will be treated as though it occurred at 10:10.

• Punch at 10:15 will be treated as though it occurred at 10:20.

Example 2:

Pay Interval Round time set to 15 minutes.

• Punch at 10:07 will be treated as though it occurred at 10:00.

• Punch at 10:08 will be treaded as though it occurred at 10:15.

To edit Pay Interval Round:

• Click the Shifts button on the left Navigation Bar or click View on the top menu bar and

choose Shifts. Select the shift you want to modify, and then select the ‘Shift Settings’ tab.

• Choose the desired Pay Interval Round value from its drop-down list. Choices include 1, 5, 6,

10 or 15 minute(s). The default value for Pay Interval Rounding is 1 minute.

• Click the Save button when done. To quit without saving changes, select another option from

the left Navigation Bar or click the Refresh button at top right and then click No in the Save

Changes dialog box.

Max Time on Clock

The Max Time on Clock setting prevents the system from calculating erroneously large worked time totals

(and possible overtime) due to missed punches. The system assumes that an employee has missed a

punch after the maximum time on the clock has been exceeded. The system will change the employee's

status to Out with zero accumulated time after the maximum time has passed since the last In/Transfer

punch. A flag will also be set that there is a missing punch on the Punch Editing screen and on the Time

Card and Hours Summary reports.

You can then enter the missing punch via Punch Editing so the employee’s time can be correctly

calculated.

The default value for Max Time on Clock is twelve hours (12:00).

Note: To disable this feature, set Max Time on Clock to zero hours (00:00).

To edit the Max Time on Clock setting:

• Click the Shifts button on the left Navigation Bar or click View on the top menu bar and

choose Shifts. Select the shift you want to modify, and then select the ‘Shift Settings’ tab.

• Enter the desired value in the Max Time on Clock field.

• Click the Save button when done. To quit without saving changes, select another option from

the left Navigation Bar or click the Refresh button at top right and then click No in the Save

Changes dialog box. Changing Max Time on Clock will apply to the Previous, Current and

all future Pay Periods.

Day Change Offset

A normal day by default begins at exactly 12:00 AM. Some companies, however, may have employees

who work shifts that end at 12AM or even into the next day. Also, there may be shifts that begin at 12AM

or earlier.

Day Change Offset can be used to 'move' such employees’ workday change time backward or forward

from 12AM so their hours are credited to the proper workday. The Day Change Offset field displays

HH:MM.

• If you do not have employees that begin or end work through 12AM, leave this setting at the

default value [00:00].

timeQplus Administrator Functions - Shifts

06-0414-000 Rev. C

• If you have employees that begin work on Day1 but end work on Day2, and the hours worked

should be allocated to Day1, set Day Change Offset to the following calculated value:

[Shift Stop Time + Shift Stop Round]

Example: If your shift stops at 4:30 AM and you have a 30-minute shift stop round, the

Day Change Offset is set to [5:00].

• If you have employees that begin work on Day1 and end work on Day2, and the hours worked

should allocated to Day2, set the Day Change Offset to the NEGATIVE of the following calculated

value:

[12:00 – Shift Start Time + Shift Start Round]

Example: If your Shift starts at 11:00 PM and you have a 15-minute shift start round, the

Day Change Offset is set to [-01:15].

To edit Day Change Offset:

• Click the Shifts button on the left Navigation Bar or click View on the top menu bar and

choose Shifts. Select the shift you want to modify, and then click on the ‘Shift Settings’ tab.

• Enter the appropriate value in the Day Change Offset field.

• Click the Save button when done. To quit without saving changes, select another option from

the left Navigation Bar or click the Refresh button at top right and then click No in the Save

Changes dialog box.

timeQplus Administrator Functions - Shifts

06-0414-000 Rev. C

Shift Rules

Check the Shift Rules Enabled box to modify Shift Start, Shift Stop, Round, Grace and Dock values.

Click the Save button when finished. If you do not wish to make use of the Round, Grace or Dock

features, leave the minutes set to zero. The following table describes each setting in more detail.

Shift Name: The name of this shift as you would like it to appear on reports and

screen displays.

Shift Start Time: The time of day employees are scheduled to start work. Pay careful

attention to the AM and PM settings to ensure your times are set

correctly.

Shift Stop Time: The time of day employees are scheduled to stop work. Pay careful

attention to the AM and PM settings to ensure your times are set

correctly.

Shift Round: The number of minutes before the scheduled Start time that an

employee’s "early" punch in will be treated as if it occurred exactly

at the scheduled Start time, or the number of minutes after the

scheduled Stop time that an employee’s "late" punch out will be

treated as if it occurred exactly at the scheduled Stop time.

This setting allows employees to clock in a few minutes early or

clock out a few minutes late, say, for time spent getting a cup of

coffee in the morning or gathering their personal belongings before

leaving work, without accumulating overtime. It does not change

the actual punch time recorded by the system, only how that punch

is treated for the purpose of calculating the employee’s worked

time.

You can set different numbers of minutes for Start Round and Stop

Round, if desired. If you do not wish to use this setting, set Start

Round and Stop Round to zero.

Note that U.S. law prohibits rounding of more than 15 minutes.

Shift Grace: The number of minutes after the scheduled Start time that an

employee’s "late" punch in is still considered on time, or the number

of minutes before the scheduled Stop time that an employee’s

"early" punch out is considered on time.

This setting allows an employee to clock in a few minutes late or

clock out a few minutes early without being docked. It does not

change the actual punch time recorded by the system, only how

that punch is treated for the purpose of calculating the employee’s

worked time.

You can set different numbers of minutes for Start Grace and Stop

Grace, if desired. If you do not wish to use this setting, set Start

Grace and Stop Grace to zero.

timeQplus Administrator Functions - Shifts

06-0414-000 Rev. C

Shift Dock: The number of minutes an employee will lose from their daily total

for punching in late or punching out early outside of the parameters

of the Shift Grace setting.

Shift Dock works together with Shift Grace to determine employees’

calculated work time. If an employee clocks in or out during the

time designated as Shift Grace, the employee’s time will not be

docked. If Start Dock is set to zero, an employee who clocked in

one minute after the end of the Start Grace period would only be

docked the amount of time elapsed form the end of Start Grace. In

other words, if your Shift Grace period is set to five minutes, an

employee who punches in six minutes late would only be docked

one minute.

You can use the Shift Dock setting to override the effect of the Shift

Grace period for employees who punch in a few minutes outside

the Shift Grace period.

For instance, if you set Start Grace to five minutes and Start Dock

to 10 minutes, an employee who clocked in at three minutes after

the scheduled shift start time (within the Shift Grace period) would

not be docked. That employee’s punch would be treated as though

it had occurred at the shift start time for the purpose of calculating

employee worked time.

However, if an employee clocked in at seven minutes after the

scheduled shift start (outside the five minute Shift Grace period but

within the 10 minute Shift Dock period), that employee’s punch

would be treated as though it had occurred at 10 minutes after the

shift start for the purpose of calculating the employee’s work time.

If an employee clocked in at twelve minutes after the scheduled

shift start (outside the periods covered by both Shift Grace and

Shift Dock), that punch would simply be treated as though it

occurred at its actual time for the purpose of calculating the

employee’s worked time.

You can set different numbers of minutes for Start Dock and Stop

Dock if desired. If you do not wish to use this setting, set Start Dock

and Stop Dock to zero.

Lunch Rules

If you wish to apply lunch rules, click the Lunch Rules tab and then check the Lunch Rules Enabled box.

Enter the scheduled Lunch Start, Lunch End, Lunch Duration, and Auto After values. Click the Save

button when done. To disable the Lunch Duration and/or Auto After feature, set their values to zero.

timeQplus Administrator Functions - Shifts

06-0414-000 Rev. C

The following table describes each lunch setting in more detail.

Lunch Start: The earliest time of day at which an employee can punch out for

lunch. If an employee clocks out before this time, the system

assumes the punch does not relate to a lunch period, and lunch rules

will not be applied.

Lunch End: The latest time of day at which an employee should punch in from

lunch.

The system assumes employees will take their entire lunch

break within the window between Lunch Start and Lunch

End. It assumes a return after Lunch End indicates a longer-

than-normal lunch period.

If an employee clocks out to lunch after Lunch Start but

before Lunch End (which puts Lunch Rules in effect), then

clocks in from lunch after Lunch End, the difference between

Lunch End and the time the employee actually clocks in will

be added to the Lunch Duration to calculate the total time

deducted from the employee’s hours worked total for lunch.

You may need to adjust the hours worked totals for such

employees using the Punch Editing screen if the time

deducted exceeds their actual lunch time taken.

If you find you consistently have to make this adjustment for

many employees, you may wish to consider modifying your

Lunch End setting to a later time.

Lunch Duration: The minimum number of minutes subtracted from time worked totals

for each lunch period. If an employee is clocked out for lunch longer

than the designated Lunch Duration, the system will deduct the

actual amount of time the employee is clocked out. However, if an

employee takes a shortened lunch – that is, clocks out after the

designated Lunch Start and clocks back in before the amount of time

set in the Lunch Duration field has elapsed – the system will

automatically deduct the full Lunch Duration.

This setting can be useful in structured environments such as

a production line, where employees must take standard-length

lunch breaks. Enforcing a standard Lunch Duration will ensure

you do not overpay employees in the event they clock back in

from lunch early before they can actually start work.

In other types of environments, use caution with this setting

to ensure you do not underpay employees who take

shortened lunch breaks. You may need to adjust the hours

worked totals for such employees using the Punch Editing

screen if the time deducted exceeds their actual lunch time

taken.

timeQplus Administrator Functions - Shifts

06-0414-000 Rev. C

Auto Lunch After: The length of time an employee can be on the clock before the

system assumes they have missed punching out for lunch and

automatically deducts the Lunch Duration from their hours worked

total. If the Lunch Duration field is set to zero, the Auto Lunch After

setting will have no effect.

Use caution with this setting. If an employee skips lunch,

and you have Auto Lunch After configured, the Lunch

Duration will automatically be deducted from their hours

worked total. You must manually add that time back using the

Punch Editing screen in order to avoid underpaying that

employee.

You can view the adjustments made to individual punches by the

system as dictated by the shift and lunch rules you configured by

selecting a punch affected by these rules in the Punch Editing screen

and clicking the DETAILS button.

Overtime

Overtime specifies the amount of time an employee must work before overtime will begin to accumulate.

The threshold amounts may be set on both a daily basis and/or weekly basis. Both the daily and weekly

overtime thresholds may be set at two different levels to reflect company policy.

Example 1:

If you pay overtime based only on the number of hours worked in a week, not on the number of hours

worked in a given day, set the Daily Level 1 and Daily Level 2 to 24:00 hours. If you do not pay a second

level of overtime on a weekly basis, set Weekly Level 2 to 168:00 hours.

timeQplus Administrator Functions - Shifts

06-0414-000 Rev. C

Example 2:

You pay employees at 1.5 times their pay rate (time and a half) if a given employee works over 40 hours

in a week and 2 times the normal pay rate (double time) if the employee works over 48 hours in a week.

To implement these rules, set Weekly Level 1 to 40 hours and Weekly Level 2 to 48 hours. If an

employee then works 60 hours in a particular week, the totals generated will be:

• Regular: 40:00

• Overtime 1: 08:00

• Overtime 2: 12:00

To edit the Overtime Threshold Values:

• Click the Shifts button on the left Navigation Bar or click View on the top menu bar and choose

Shifts. Select the shift you want to modify, and then click the ‘Overtime’ tab.

• Check the Overtime Enabled box and type the desired overtime thresholds in the Daily Level 1,

Daily Level 2, Weekly Level 1 and Weekly Level 2 fields.

• Click the Save button when done. To quit without saving changes, select another option from the

left Navigation Bar or click the Refresh button at top right and then click No in the Save Changes

dialog box.

7th Day Overtime

When enabled, 7th Day Overtime will promote all hours worked on the seventh consecutive worked day

to the next higher pay level (Overtime 1 or Overtime 2), provided that the 7 consecutive days start at the

beginning of the a given week of the pay period. This rule affects only the Daily Overtime calculations and

will not overwrite any Weekly Overtime rule settings. To enable 7th Day Overtime, check the ‘Enable 7th

Day Overtime’ box on the Overtime tab.

Note: This feature was designed to accommodate a law commonly referred to as California Overtime.

Holidays

You can override the company-wide settings regarding holiday pay for individual shifts. If you wish

holidays to be paid for employees assigned to this shift, check the ‘Holidays are paid’ box and then enter

the number of hours to be paid for each holiday. Click the Save button when done. To quit without saving

changes, select another option from the left Navigation Bar or click the Refresh button at top right and

then click No in the Save Changes dialog box.

timeQplus Administrator Functions - Shifts

06-0414-000 Rev. C

Salaried Shift Settings

The Salaried shift determines how salaried employees will be paid.

To Change Salaried Employee Settings:

• Click the Shifts button on the left Navigation Bar or click View on the top menu bar and choose

Shifts. Select ‘Salaried’ from the ‘Select a Shift’ drop down list.

• Under the General tab, you can specify the number of hours per Pay Period to pay salaried

employees. The default value is 40 hours, which can be updated if necessary. This value is

exported every pay period to payroll.

• If salaried employees are to be paid for holidays, then under the Holidays tab, check the

Holidays are paid box and enter the number of hours to pay for each holiday in the Hours to pay

for each Holiday field; the default is 8:00 hours.

• Click the Save button when done. To quit without saving changes, select another option from the

left Navigation Bar or click the Refresh button at top right and then click No in the Save Changes

dialog box.

timeQplus Administrator Functions – Punch Editing

06-0414-000 Rev. C

Punch Editing

Punch Editing allows administrators and supervisors to do the following:

• Review and edit employee transactions

• Adjust the total time accumulations

• View the details of transaction totals and how the software calculated the transactions

• Add missed punches

• Modify Work Codes

• Add miscellaneous transactions (Vacation, Sick Time, Other, Holiday, FMLA)

• Approve an employee’s time card

• Print an employee's time card

To access the Punch Editing screen, click the Punch Editing button on the left Navigation Bar or click

View on the top menu bar and choose Punch Editing.

timeQplus can store several different types of transactions:

• PUNCH (CLK): a normal punch In or Out on a connected Time Clock

• INSERTED (INS): an entry inserted using the Punch Editing screen.

• PUNCH (PC): an entry created when an employee clocks In or Out using the Virtual Clock

• TIMESLIP (SLP): an entry created when a salaried employee submits a transaction using the

Submit Employee TimeSlip feature on the Virtual Clock (salaried employees only)

The code (CLK, INS, PC, and SLP) at the left of each transaction line in the Punch Editing screen

identifies the type of transaction. These various types of transactions allow for Salaried Exempt and

Salaried Non-Exempt employees, as well as hourly employees, to use the software.

timeQplus Administrator Functions – Punch Editing

06-0414-000 Rev. C

Managing Transactions

To insert a transaction:

• On the Punch Editing screen, select employee from the ‘Select an Employee’ drop-down list.

• Select the appropriate pay period from the ‘Choose a Pay Period’ drop-down list. Be certain to

confirm transaction being inserted occurs within the date range of the pay period.

Note: Transactions added to the Future pay period will appear in the Future Transactions

Report until such time as the Pay Period in which the transaction occurs becomes the Current

pay period.

• Enter the Date of the transaction you are inserting in the field in the Insert section of the

Transaction area at the bottom left of the screen. You may simply type the desired date in the

field, or click the arrow at the right of the field to open a calendar to select the correct date.

• Select the type of transaction to insert from the ‘Type’ drop-down menu: PUNCH, HOL (Holiday),

VAC (Vacation), SIC (Sick leave), REG (Regular time), FMLA (Family Medical Leave Act) or OTH

(Other). The transaction type is displayed in the IN/OUT column.

Note: The REG transaction is useful to add hours when an employee forgot or otherwise unable

to clock both in and out. The effect of adding hours via the REG transaction is essentially the

same as adding two individual PUNCH transactions for a missed In punch and a missed Out

punch.

• Enter the correct Time for the transaction you are inserting. If you are inserting a PUNCH, enter

the time when the punch should have taken place. For other inserted transactions (HOL, VAC,

SIC, REG, OTH or FMLA), enter the number of Hours to apply to this transaction. You may

simply type the correct value in the field; or, for Time, use the up or down arrows at the right of

the field to adjust the time.

• If applicable, select a Work Code from the drop down list.

• Click the Insert button or press the <ALT> then the "I" key on your computer keyboard.

o When inserting a PUNCH transaction, you will be prompted to enter a comment, maybe

why the transaction was added, for example. Enter text in the blank box and click the

Save button.

o Click the No Comment button to skip entering a comment and save the transaction. To

permanently disable the Comments dialog box, check the Don’t display this dialog again.

o To enable the Comments dialog box after permanently disabling it, click File >

Supervisor Preferences… on the top menu bar, check the Show Punch Comment

Dialog box, and then click Save.

o You can view comments by selecting an inserted PUNCH transaction and clicking the

Details button.

• The transaction will now appear on the Punch Editing Screen.

timeQplus Administrator Functions – Punch Editing

06-0414-000 Rev. C

To delete a transaction:

• On the Punch Editing screen, select employee from the ‘Select an Employee’ drop-down list.

• Select the appropriate pay period from the ‘Choose a Pay Period’ drop-down list.

• Click the transaction to be deleted.

• Click the Delete button, or simultaneously press the <ALT> and D keys on your keyboard.

Note: When a PC or SLP transaction is deleted in Punch Editing, the timeQplus software does not

actually remove the transaction from the database. The transaction will no longer appear in the Punch

Editing screen, but will appear on the Time Card Report in a separate section entitled “Deleted

Transactions”. These deleted transactions are ignored in calculating the employee's total time

accumulation.

To view deleted transactions:

On the Punch Editing screen, select the desired employee and Pay Period from the drop down lists and

then click the View Deleted button. If an employee does not have any deleted punches during the

selected Pay Period, the View Deleted button will be grayed out.

To view the details of a transaction, including adjustments arising from the use of Round, Grace,

Dock or lunch rules:

• On the Punch Editing screen, select employee from the ‘Select an Employee’ drop-down list.

• Select the appropriate pay period from the ‘Choose a Pay Period’ drop-down list.

• Select a transaction. Click the Details button or simultaneously press the <ALT> and T keys your

keyboard. The Punch Details screen appears. It lists the rules applied to both the IN and OUT

punch as well as adjustments made to the total time.

• Click the Ok button to exit the Punch Details screen.

Editing Total Time Accumulations

To edit total time accumulations:

• On the Punch Editing screen, select employee from the ‘Select an Employee’ drop-down list.

• Select the appropriate pay period from the ‘Choose a Pay Period’ drop-down list.

• Click the +/- Edit Totals button or simultaneously press the <ALT> and E keys on your keyboard.

This will launch the Edit Totals screen, which will allow you to add or subtract time from an

employee's totals.

• Enter the number of hours and minutes to be added to or subtracted from the Regular, Overtime

1 or Overtime 2 categories. A value of 0:00 means that no time will be added to or subtracted

from the employee's total time accumulations for that category.

timeQplus Administrator Functions – Punch Editing

06-0414-000 Rev. C

• When subtracting time, enter a minus sign (-) before the number of hours and minutes. When

adding time, simply type the number of hours and minutes to be added. You do NOT need to

insert a plus sign (+) in front of the number.

• Click the Save button to accept changes or the Cancel button to exit the Edit Totals screen

without saving changes. The changes you enter are reflected on the Punch Editing screen in the

Totals area in the Edits and Totals columns.

Note: The edited hours are added to or deleted from the overall pay period totals. They are not allocated

to a particular day.

Printing Time Cards

An employee’s Time Card can be printed from either the Punch Editing screen by clicking the Print

button at the upper right corner or from the Reports screen by following the steps below.

To print a Time Card using Reports:

• Click the Reports button on the left Navigation Bar or click View on the top menu bar and choose

Reports.

• Select the Time Card report.

• Choose the appropriate Pay Period from the ‘Choose a Pay Period’ drop-down list.

• On the Filters and Sorting area, select whether to print all employees, individual employees,

salaried employees only or employees assigned a specific shift.

• To include Work Codes, check the Include work codes box.

• When printing individual employees, select the specific employees to include from the list in the

box at the right of the screen. To print one employee, click that employee’s name. To print

multiple employees, press and hold the CTRL key while clicking each employee name.

• When printing an entire shift, select the desired shift from the drop-down list that appears below

the filter selection.

• Select the desired sort order from the ‘Sort By’ drop-down list. By default, employees are sorted

in alphabetical order by last names. You can change the sort order to alphabetical by first name

or numerical by badge number, employee number or shift.

• To print the report, click the Print button. To preview the report before printing, click the Preview

button.

timeQplus Administrator Functions – Reports

06-0414-000 Rev. C

Reports

The Reports screen allows reports to be generated for preview, print, or export. It also allows

administrators to search for past and present employees using the Employee Search button (located in

the upper right corner of screen). The search results will contain data on when an employee was added to

and, if applicable, removed from the timeQplus software.

To access the Reports screen, click the Reports button on the left Navigation Bar or click View on the

top menu bar and choose Reports.

Certain reports offer filter options: All Employees, selected Individual Employee(s), only Salaried

Employees or Individual Shift; and sorting options: Last Name, First Name, Badge Number, Employee

Number or Shift.

Generating a Report

To generate a report:

• On the Reports screen, select the type of report you wish to print.

• If applicable, select the desired Pay Period, Pay Period Range, or Date Range. Please refer to

Table 1 for a list of reports along with the available options and maximum date range values for

each.

• Select the filter criteria when applicable. For certain reports, you may choose to filter your report

to include All Employees (the default), selected Individual Employee(s), only Salaried Employees

or all employees assigned to an Individual Shift. If filtering is not applicable to the report you have

selected, the options will be grayed out.

• If filtering by Individual Employee(s), select the desired employee's name in the ‘Select

Employees’ box at the right of the screen. To select more than one employee, press and hold

down the CTRL key while clicking each employee name.

• If Individual Shift is selected, select the shift in the drop down list that appears below the filter

selection.

• Select the sorting method, if applicable. You may choose from alphabetical by first name or last

name (the default) or numerical by badge number, employee number, or shift.

timeQplus Administrator Functions – Reports

06-0414-000 Rev. C

• Select the output (where you want the report to go). Choices include:

o Print – print a paper copy of the report

o Preview – preview a copy of the report before printing

o Export – create an electronic copy of the report. Format options include:

 Image (*.tiff)

 Adobe PDF (*.pdf)

 Web Archive(*.mhtml)

 Microsoft Excel (*.xls)

 CSV (*.csv)

Table 1

Available Report Options

Report Pay

Period

Pay

Period

Range

Date

Range

Max # of Weeks in

Pay Period Range

or Date Range

Approaching Overtime

Average Totals By Employee 9 52

Daily Totals By Day 9 9 5

Daily Totals By Employee 9 9 5

Employees By Supervisor

Employee Default Work Codes

Employee Profiles

Holidays 9

Hours Summary 9 9 53

Missing Punches 9

Punch Comments By Employee 9

Raw Transactions 9

Rules Setup 9

Shifts 9

Supervisors By Employee

Time Card 9 9 53

Time Card Approvals 9

Who’s IN, Who’s OUT

Work Codes Totals By Employee 9 9 5

Work Codes Totals By Work Code 9 9 5

Future Transactions Report

The Future Transactions Report shows all transactions that have been entered into the system with

dates that occur after the end of the current pay period. These transactions will automatically be properly

inserted into the appropriate pay period as it becomes current. To print a Future Transactions report:

• On the Reports screen, select the Time Card report.

• Select the Pay Period option and then choose the Future pay period from the drop down list.

• Click the Preview button to view the report on-screen, the Print button to produce a paper copy,

or the Export button to produce an electronic copy of the report.

timeQplus Administrator Functions – Export

06-0414-000 Rev. C

Export

The timeQplus system is designed to work with most common payroll programs. The Export screen

allows employee time and attendance data to be exported to a file so it can later be imported into a

database, spreadsheet, payroll software, or payroll service provider.

To access the Export screen, click the Export button in the left Navigation Bar or click View in the top

menu bar and choose Export.

Exporting Time and Attendance Data

To export time and attendance data:

• Select the Pay Period you want to export. You can choose to export data for the current, previous

or archived pay period.

• Select the desired filter option. You can choose from All Employees, all employees assigned to

an Individual Shift, or Individual Employee(s). If you choose Individual Shift, select the desired

shift from the drop down list that appears below the filter selection. If you choose Individual

Employee(s), select the desired employee name from the box at the right. To include multiple

employees in the export, you may hold down the CTRL key while clicking each employee name.

• Select the desired Output Format from the drop-down list.

• Click the Export button. The first time you attempt to export to a particular Output Format you will

be presented with a configuration screen in which you can set options specific to that format.

Once you have configured the output format as necessary, click the Save button to continue with

the export. On subsequent exports to that output format, the export will begin immediately.

• A Save As dialog will appear. Enter the file name and location for the data to be exported. Click

the Ok button to save the file, or click the Cancel button to return to the Export screen.

• To edit a previously configured Output Format, select the desired format from the drop down list

and click the Setup button to open the configuration screen for that format. Make the necessary

changes and click the Save button or click the Cancel button to exit.

timeQplus Administrator Functions – Export

06-0414-000 Rev. C

Unapproved Timecards

The Unapproved Time Cards window is displayed when attempting to export time card and/or time

sheet data to payroll and not all employees’ Time Cards and TimeSlips have been approved. This feature

can be disabled by de-selecting the option to require approval in the Setup screen.

From this window you can print a list of unapproved time cards and time slips by clicking the Print button

or click the Close button to exit.

To approve an employee Time Card, go to the Punch Editing screen, select the employee from the

‘Select an Employee’ drop down list, choose the appropriate pay period, and click the Approve button.

Advanced Payroll Integration

QuickBooks Payroll Integration

File Payroll Export Formats

Custom Export File Builder V1.5 Peachtree Complete Import File V7.0

Generic V2.0 Premier Import File V2.0

Generic ASCII Export file builder Premier Plus Import File V2.0

ADP Version 7.0 PrimePay PrimeLink Import File V10001

Genesys Inbound Timecard QuickBooks Integration

Intuit PC Access Import File V2.0 QuikPay Import File V2.0

Intuit PC Access Jr Import File V2.0 QuikPay Plus Import File V2.0

Oryel Payroll Export Wells Fargo Import File V2.0

PayChex Paylink Import File 5.0 Wells Fargo Plus Import File V2.0

PayChex Preview Import File V0002 Wells Fargo Timeclock Import File

PayChex IM0007 Import File Heartland PlusOne Fixed Length File

Peachtree Complete 2006 Import File

timeQplus Administrator Functions – Export

06-0414-000 Rev. C

Custom Export File Builder

Click Here to Open an Existing Template

Opens a saved Export setup.

Insert Quotes Around Non-Numeric Select Y to put quotes around all Alpha or Alpha-

Numeric values.

Note: Quotes will only appear in .txt Export File

Formats.

Include Column Heading … Select Y to include the Column Heading in the

export.

Example: the column heading for "Vacation" could

be "Vacation", "Vac", "V", etc. The exact name that a

payroll program needs can be entered into the

"Properties" table by typing over the default name in

the "Export Code" column.

Custom Export File Header Lines

Lines per Employee

Custom Export File Trailer Lines

You can specify the number of lines of data that will

appear in the Header and Trailer records. You can

also specify the number of lines that will be

displayed for each employee in the Employee Data

Section.

timeQplus Administrator Functions – Export

06-0414-000 Rev. C

Include in Total Lines Checksum

Header Lines

Employee Data Lines

Trailer Lines

Determines which lines of data are used to compute the

Total Lines in the Export. This is used as a checksum or a

comparison value by some Payroll programs. Select Y to

include the lines in the Total Lines checksum.

Line Terminator:

CRLF - Carriage Return Line Feed

CR - Carriage Return

LF - Line Feed

Custom

Custom Line Terminator – appears when Custom is chosen. Enter a single

character that your payroll program treats as a line terminator (the end of a

line of data).

Field Separator:

Tab

Comma

Slash

Semi-Colon

Custom

Custom Separator – appears when Custom is chosen. Enter a single

character that your payroll program treats as the beginning and end of a data

element.

Fixed Length – sets the length of each attribute to a fixed length. When Fixed

Length is chosen a "Fixed Length" column will be displayed in the Properties

Table where each attribute can be set to the required fixed length.

Time Format: HH:MM (hours : minutes)

HH.XX (hours.decimal hours)

HHMM (hours minutes) (Export without colon)

HHXX (hours decimal hours) (Export without decimal)

Date Format: MM / DD / YYYY

DD / MM / YYYY

MM.DD.YYYY

DD.MM.YYYY

MM-DD-YYYY

DD-MM-YYYY

YYYY/MM/DD

YYYY-MM-DD

YYYY.MM.DD

MMDDYYYY

DDMMYYYY

YYYYMMDD

timeQplus Administrator Functions – Export

06-0414-000 Rev. C

User Defined Fields in Export Number of Custom Export Fields; valid values are 0 to 999.

This value will set the number of Custom Export fields (lines) in

the Properties Table.

Totals Exported by: Pay Period

Day

Export File Format: csv Comma separated values

txt Text Document

Configure Export File Layout

The Export Layout has three sections:

1. Header Record - contains info that identifies the payroll export such as Export ID, Company

Name, Payperiod Start Date, Payperiod End Date, Export Creation Date, Export Creation Time,

etc.

2. Employee Data - contains all data necessary for processing the payroll, i.e., the actual time and

benefits that each employee accumulated or used.

3. Trailer Record - The trailer record usually reiterates information contained in the header record.

The number of lines that appears in each section depends on the number of lines specified for each

section in the Main Setup Screen.

The "# of Field" is where the number of data elements for each line can be specified. If you type "4" in the

block you will see (4) blank fields appear with each field having a drop down list of the elements you can

select to specify the field. Note that you can increase the number of fields per line at any time in order to

add additional fields. You can also decrease the number of fields at any time. The fields at the end of the

line will drop off as you decrease the number.

Click Save to save and exit the Export Layout. Click Cancel to exit without saving your changes.

Export Properties Table Setup

If “Fixed Length” is selected from the ‘Field Separator’ drop down list, the Custom Export Properties Table

appears as follows:

timeQplus Administrator Functions – Export

06-0414-000 Rev. C

When any other selection except “Fixed Length” is selected from the ‘Field Separator’ drop down list, the

Custom Export Properties Table appears as follows:

• Export Field – The values in this column are all the data elements that are available for export to

a payroll program. Note that the number of “Custom x” data elements is controlled by "User

Defined Fields in Export" in the Main Setup Screen.

• Export Code - For all fields you can type in the required name for any attribute that your Payroll

program requires in the "Export Code" column. Example: the attribute "Overtime Level 1" may

be imported by a Payroll program as "OT1". In the "Export Code" column beside "Overtime Level

1" you would type the name "OT1" over the default name "Overtime Level 1".

• Custom Value – The "Custom x" attributes are static data elements that are exported with every

export. An example might be "Company Name". You would type the Company Name in the

"Custom value" column beside Custom 1 over the default value "Custom 1". Custom Value only

applies to the Custom data attributes. Typing a value for any of the other data elements will not

have an effect.

timeQplus Administrator Functions – Export

06-0414-000 Rev. C

• Format – The format of each data element can be set as either Alphanumeric, Numeric, Date or

Time. To change the default value, click on the field and select the new value from the pull-down

list.

• Fixed Length – When Fixed Length is chosen for the field separator the "Fixed Length" column

will be shown in the Properties Table. Each attribute has a default Fixed Length value. To

change the value simply type the new value over the default value, i.e., if "First Name" must be

limited to 8 characters by the payroll program type "8" over the default value of "10". Only the

first "8" characters of the First Name will be exported (Right or Left Alignment has no effect on

which characters are exported).

• Alignment – When Fixed Length is chosen for the field separator the "Alignment" column will be

shown in the Properties Table.

Save Template Saves the current Export file setup as a .dat file in the "ExportTemplates"

folder.

Note: You must click "Save" in order to save the current template as the

active template. If you do not click "Save" the current template form will

not be available the next time you open the export. You will have to

reconfigure it or retrieve a saved template.

Template Location Win XP: C:\Program Files\Acroprint\timeQplusV3\exporttemplates

Vista, Win7 & 2008 Server: C:\Program Data\Acroprint\timeQplus\Export

Templates

Clear Form: clears all data from the current Export and returns all settings to default values

Help: activates timeQplus Help

Layout Preview: gives a quick view of the layout of the Export.

• This is not a preview of the actual export but simply shows the data elements (if column headings

are chosen for display) and the Field Separators and Line Terminators.

• If the Export Date and Export Time are part of the export they will show as actual values.

Save: saves the current Export settings

Cancel: closes the Main Setup screen without saving any changes

QuickBooks® Payroll Integration

timeQplus easily exports employee Time Card data to QuickBooks. Work Codes can be included in the

export as well.

The following topics will guide you throughout the export process:

• Setting up QuickBooks® to communicate with timeQplus

• Setting up timeQplus to Communicate with QuickBooks®

• Exporting timeQplus data to QuickBooks®

Setting up QuickBooks® to communicate with timeQplus

Before You Begin

Make sure QuickBooks® Pro/Premier is installed on your local computer and that you have access to the

company file (*.QBW).

Enable Time Tracking in QuickBooks®

To turn on time tracking (in QuickBooks Pro/Premier 2013 or later):

1. From the Edit menu, choose Preferences.

2. In the Preferences window, select Time & Expenses from the scroll box on the left.

3. Click the Company Preferences tab and select Yes for "Do You Track Time?"

timeQplus Administrator Functions – Export

06-0414-000 Rev. C

Note: QuickBooks may close all windows after this setting has been changed.

4. In the Preferences window, select Payroll & Employees from the scroll box on the left.

5. On the Company Preferences tab, click the Employee Defaults button.

6. If not already, check "Use time data to create paychecks”.

7. Click OK to close the Employee Defaults window, and then click OK again to close the

Preferences window.

Note: In previous versions of QuickBooks Pro/Premier, some items listed on the left in the Preferences

window may be labeled differently. Please refer to your QuickBooks ® documentation for more

information on these settings.

If employees were added to QuickBooks prior to enabling time tracking, each employee must be set up to

use timesheets to track hours. This must be done one employee at a time.

To turn on time tracking for a single employee:

1. On the top menu bar, choose Employees > Employee Center.

2. Double-click the employee in question.

3. Choose Change Tabs > Payroll and Compensation Info. In QuickBooks 2013, click the

Payroll Info tab.

4. Under the Earnings box, check the Use time data to create paychecks box.

5. In Pay Frequency ensure the employee is set up for the correct frequency (i.e. If an

employee has a Pay Frequency set for Annual all time sheets from the ending pay

period date to the prior year will be pulled into the paycheck), be sure Pay Period and

Payroll Schedule are correct.

6. Click OK.

Create Hourly Wage Pay Items in QuickBooks®

QuickBooks must be setup with a unique Hourly Wage Pay Item for each of the following timeQplus time

types: Regular, Overtime 1, Overtime 2, Vacation, Holiday, Sick, and Other. Please refer to your

QuickBooks® documentation for information on how to create and modify Hourly Wage Pay Items.

In timeQplus, the default values for each Hourly Wage Pay Item are:

• Regular Pay • Holiday Pay

• Overtime Pay • Sick Pay

• Premium Overtime Pay • Other Pay

• Vacation Pay

Please make note of the exact name for each Hourly Wage Pay Item from QuickBooks. This information

will need to be entered in timeQplus prior to exporting employee time card data.

Add Employees

If you attempt to export an employee’s timecard to QuickBooks®, and the employee does not exist in the

application, you will be prompted to add the employee(s) at the time of the export.

Add Work Codes

If Work Codes should be included when exporting to QuickBooks®, they will need to be defined as

customers. The spelling of the customer name in QuickBooks® must exactly match the spelling of the

work code name in timeQplus. Please refer to your QuickBooks® documentation for information on how

to create and modify your customer list.

Setting up timeQplus to Communicate with QuickBooks®

For the QuickBooks® Integration, each employee name must be a unique combination of characters.

Since timeQplus does NOT enforce uniqueness among employee names, it uses the Export ID assigned

to each employee to export time card data to QuickBooks.

When adding to timeQplus an employee who already exists in QuickBooks, enter the full employee name,

exactly as it appears in QuickBooks, in the Export ID field on the employee’s Employee Profile screen in

timeQplus.

timeQplus Administrator Functions – Export

06-0414-000 Rev. C

When adding to QuickBooks employees who already exist in timeQplus, make sure each employee name

entered in QuickBooks exactly matches the Export ID of each employee in timeQplus.

Exporting timeQplus data to QuickBooks®

1. On the Export screen, select the Output Format: QuickBooks Integration.

2. Click the Export button

Note: If you have never chosen a QuickBooks® company file (*.QBW) or mapped your pay codes and

work codes (if applicable), you will need to do so before you can run the integration.

Data Export Setup Screen

Step 1 – Select Company File

Click Select to select the QuickBooks® company file (*.QBW) you created for your company.

Step 2 – Setup Pay Codes

Map the timeQplus Pay Code to the corresponding Wage Pay Item in QuickBooks®.

If this is the first time you are running the integration, please have QuickBooks® running and your

company file opened. You will not be required to have QuickBooks® running in the future.

Step 3 – Include Work Codes

If work codes are to be included in the export, check the ‘Include Work Codes’ box.

Note: In order for work codes to be properly exported to QuickBooks®, they will need to be defined

in QuickBooks® as customers (timeQplus does not currently support the export of work codes when

defined as jobs in QuickBooks®). The work code name in timeQplus must exactly match the

customer name as defined in QuickBooks®.

Step 4 – Click OK to run the integration

If this is the first time you are running the integration, QuickBooks® will prompt you that an

application without a certificate is attempting to access your company file.

Click Yes, Always to allow timeQplus to integrate with QuickBooks®

Add Missing Employees to QuickBooks

If you are attempting to export timecard data for an employee who is not found in QuickBooks® you will

be prompted by timeQplus to add the missing employee to QuickBooks.

Missing Payroll Items

If you are attempting to export timeQplus Pay Codes that do not exactly match one of the QuickBooks®

Payroll Items, you will be prompted by timeQplus and the integration will be canceled.

Note: The spelling of the Pay Codes and corresponding Payroll Items must be identical.

Missing Work Codes

If you are attempting to export timeQplus Work Codes that do not exactly match one of the

QuickBooks® Customer names, an error will occur and the integration will be canceled. If the ‘Include

Work Codes’ box is checked, each work code in timeQplus must be defined as a customer in

QuickBooks® before the export can continue.

Note: The spelling of the Work Code names and the corresponding Customer names must be identical.

Peachtree Complete Accounting

Before exporting employee time card data to Peachtree Complete Accounting, you must first configure

the following:

• Inventory Items – You must set up inventory item(s) that are associated with REG, OT1, OT2,

VAC,HOL, SIC and OTH hourly wages. Normally, this is one item but may be defined individually for

each level. Please see Peachtree Accounting help for instructions on setting up Employee Time slip

Items.

timeQplus Administrator Functions – Export

06-0414-000 Rev. C

• Employees – Before you can import Time Card data to Peachtree Complete Accounting, you must

make sure that the employee IDs assigned to the employees in Peachtree match the Export IDs for

each of the employees defined in the timeQplus software.

Mismatched employee IDs will generate an error when attempting to import to Peachtree Complete

Accounting and may cause unexpected results.

Also, for each employee, you must enter Pay Rates for the 3 levels of the inventory item associated

with hourly wages along with vacation, holiday, sick and other wages. By default, the first pay level

will receive imported REGULAR hours, the second will receive imported OVERTIME1 hours and the

third will receive imported OVERTIME2 hours. The vacation, holiday, sick and other wages levels

must be set according to the desired outcome.

After creating a Peachtree Compatible file from timeQplus data, go to the Import/Export form in your

Peachtree Complete Accounting software and create a new export format including all fields and with

Field Headers in first Record selected. Then selected the timeQplus export file you just created and

execute the import to Peachtree.

Peachtree Complete Accounting Export

• On the Export screen, select Output Format Peachtree Complete Import File V7.0 or

Peachtree Complete 2006 Import File.

• Click the Export button. The first time you attempt to export you will be presented with a

configuration screen in which you can set options specific to this format. Once you have

configured the output format as necessary, click the Save button to continue with the export. You

will not be required to configure the output format options on subsequent exports.

• The software will then prompt you for the name of the Peachtree Complete export file (*.csv).

Specify a file name and location on your hard drive and click the Save button to export the data.

timeQplus exports employee time card data to a Peachtree Complete Accounting import file format based

on values entered for the following fields:

Regular Pay Level

The Peachtree Pay Level (1-20) associated with Regular Pay

Regular Pay Item Code

The Peachtree Pay Item Code associated with Regular Pay

Overtime 1 Pay Level

The Peachtree Pay Level (1-20) associated with Overtime

Level 1 Pay

Overtime 1 Pay Item Code

The Peachtree Pay Item Code associated with Overtime Level

1 Pay

Overtime 2 Pay Level

The Peachtree Pay Level (1-20) associated with Overtime

Level 2 Pay

Overtime 2 Pay Item Code

The Peachtree Pay Item Code associated with Overtime Level

2 Pay

Vacation Pay Level

The Peachtree Pay Level (1-20) associated with Vacation Pay

Vacation Pay Item Code

The Peachtree Pay Item Code associated with Vacation Pay

Holiday Pay Level

The Peachtree Pay Level (1-20) associated with Holiday Pay

Holiday Pay Item Code

The Peachtree Pay Item Code associated with Holiday Pay

Sick Pay Level

The Peachtree Pay Level (1-20) associated with Sick Pay

timeQplus Administrator Functions – Export

06-0414-000 Rev. C

Sick Pay Item Code

The Peachtree Pay Item Code associated with Sick Pay

Other Pay Level

The Peachtree Pay Level (1-20) associated with Other Pay

Other Pay Item Code

The Peachtree Pay Item Code associated with Other Pay

Output Field Titles

This value should match the Peachtree Import option chosen

when executing the actual import to Peachtree. The default is

NO.

Batch Sequence Number The first ticket number that will be used in the resultant output

file. This number should be modified only if a previous

installation of timeQplus has already been used to export

employee time cards to Peachtree. Any arbitrary changes to

this field can cause imports to Peachtree to fail.

WellsFargo, Premier, QwikPay and Intuit PC Access Import File

timeQplus exports employee hours summary data to Wells Fargo ®, Premier ® and QwikPay ® payroll

packages using the Intuit PC Access ® Time Clock Interface import file format. The following list

describes the required export configuration fields when exporting using this format.

Company Name Payroll application company name

Determined by the payroll application being used.

Regular Pay Code Payroll application pay code assigned to Regular Worked Hours

'PLUS' only...ignored in applications that use PC Access JR

format

Overtime Level 1 Pay Code Payroll application pay code assigned to Overtime Level 1 Worked

Hours 'PLUS' only...ignored in applications that use PC Access JR

format

Overtime Level 2 Pay Code Payroll application pay code assigned to Overtime Level 2 Worked

Hours

Vacation Code Payroll application pay code assigned to Vacation Hours. Check

'Export as Deduction' to export as negative hours

Holiday Code Payroll application pay code assigned to Holiday Hours. Check

'Export as Deduction' to export as negative hours

Sick Code Payroll application pay code assigned to Sick Hours. Check

'Export as Deduction' to export as negative hours

Other Code Payroll application pay code assigned to Other Hours.

Check 'Export as Deduction' to export as negative hours

ADP Version 7.0

timeQplus exports employee profile and time card data to two ADP import file formats based on values

entered for the following fields:

Company Code

The 3-character alpha-numeric ADP Company Code

Batch Sequence Number The numeric ADP Import Batch Number

timeQplus Administrator Functions – Export

06-0414-000 Rev. C

Pay Number The numeric ADP Pay Number

Overtime Level 2 Pay Code The value to use in the ADP import Coded Hours field

for Overtime Level 2 Hours

Overtime Level 2 Pay Code Name The name of the value to use in the ADP import Coded

Hours field for Overtime Level 2 Hours

Vacation Pay Code The value to use in the ADP import Coded Hours field

for Vacation Hours

Vacation Pay Code Name The name of the value to use in the ADP import Coded

Hours field for Vacation Hours

Holiday Pay Code The value to use in the ADP import Coded Hours field

for Holiday Hours

Holiday Pay Code Name The name of the value to use in the ADP import Coded

Hours field for Holiday Hours

Sick Pay Code The value to use in the ADP import Coded Hours field

for Sick Hours

Sick Pay Code Name The name of the value to use in the ADP import Coded

Hours field for Sick Hours

Other Pay Code The value to use in the ADP import Coded Hours field

for Other Hours

Other Pay Code Name The name of the value to use in the ADP import Coded

Hours field for Other Hours

Output to ADP CSV format Chooses ADP Comma Delimited format for ADP Data

Import (WINDOWS)

Output to ADP EPIP format Chooses ADP EPIP format for ADP Data Import (DOS)

Generic V2.0

timeQplus exports employee profile and time card data to a Generic ASCII delimited file based on values

entered in the following screen. Click the Save button when done.

timeQplus Administrator Functions – Export

06-0414-000 Rev. C

Generic ASCII file Export

The timeQplus software exports employee profile and time card data to a Generic ASCII delimited file

based on values entered for the following fields. Click a row and then click the Edit button to edit a

column header. Click a row and then click the up/down arrows to maneuver a row to its appropriate

position. Click the Save button when done.

Genesys & Oryel Payroll Export

Inbound timecard file layout

The purpose of these specifications is to provide you with the required format to produce time entry files.

Each record is 80 bytes long and should be padded to that length. The file is fixed without field delimiters

(such as commas, semicolons, tabs, etc. between each data field). There cannot be any null fields or

blank positions. Fields or positions that do not have data should be filled with spaces (" ") or zeroes ("0")

according to the specific field requirements.

Format Legend

Format Type Description

A Alpha

AN Alphanumeric

N Numeric

N2 Numeric 2 decimals

implied

timeQplus Administrator Functions – Export

06-0414-000 Rev. C

N4 Numeric 4 decimals

implied

File Layout

If an employee only has hours worked with no cost center or rate overrides, the following layout may be

used.

Field # Positions Length Format Field Name and Description

1 1-3 3 AN Company Identifier; Ex "PMC"

2 4-5 2 N Group Identifier Ex: 05

3 6-14 9 AN Social Security Number (no dashes)

4 15-20 6 A Space Fill

5 21-22 2 AN Literal ‘85’

6 23-27 5 AN Sequence Field ‘YMMDD’

7 28 1 AN Literal ‘1’

8 29-30 2 N Earning number Ex ‘01’ for Regular

9 31-36 6 N2 Hours, Units or Dollars and Cents

If no additional Earnings are needed, space fill the

remaining fields

10 37-38 2 N Earning number Ex ‘02’ for Overtime

11 39-44 6 N2 Hours, Units or Dollars and Cents

12 45-46 2 N Earning Number Ex ‘03’ for Doubletime

13 47-52 6 N2 Hours, Units or Dollars and Cents

14 53-54 2 N Earning Number Ex ‘05’ for Shift 2

15 55-60 6 N2 Hours, Units or Dollars and Cents

16 61-62 2 N Earning Number Ex ‘17’ Holiday

17 63-68 6 N2 Hours, Units or Dollars and Cents

18 69-70 2 N Earning Number Ex ‘19’ Jury Duty

19 71-76 6 N2 Hours, Units or Dollars and Cents

20 77-80 4 A Space Fill

If an employee has cost center or rate overrides, the following layout may be used.

Field # Positions Length Format Field Name and Description

1 1-3 3 AN Company Identifier; Ex "PMC"

2 4-5 2 N Group Identifier Ex: 05

3 6-14 9 AN Social Security Number (no dashes)

4 15-20 6 A Space Fill

5 21-22 2 AN Literal ‘82’

6 23-27 5 AN Sequence Field ‘YMMDD’

timeQplus Administrator Functions – Export

06-0414-000 Rev. C

7 28 1 AN Literal ‘1’

8 29-30 2 N Earning number Ex ‘01’ for Regular

9 31-36 6 N2 Hours, Units or Dollars and Cents

10 37-42 6 N4 Rate Override (space fill if none)

11 43-44 2 N Earning number Ex ‘02’ for Overtime

12 45-50 6 N2 Hours, Units or Dollars and Cents

13 51-56 6 N4 Rate Override (space fill if none)

14 57-62 6 A Space Fill

15 63-80 17 AN Cost Center Override

PayChex Paylink Export

timeQplus exports employee profile and time card data to a PayChex PayLink import file based on values

entered for the following fields:

Office Number The PayChex Paylink office number

Client ID Your PayChex Paylink Client ID

Site Number The PayChex Paylink Site number for the employees entered in the

Time and Attendance Software

Sequence Number The PayChex Paylink Import Sequence Number

Vacation Pay Code A valid PayChex Paylink pay code for Vacation Pay

Holiday Pay Code A valid PayChex Paylink pay code for Holiday Pay

Sick Pay Code A valid PayChex Paylink pay code for Sick Pay

Other Pay Code A valid PayChex Paylink pay code for Other Pay

PayChex Preview Export

timeQplus exports employee profile and time card data to a PayChex Preview import file based on values

entered for the following fields:

Client Number Your PayChex Preview Client ID

Regular Pay Code PayChex Preview Pay Code for Regular Hourly Wages

Overtime Level 1 Pay Code PayChex Preview Pay Code for Overtime Level 1 Hourly

Wages

Overtime Level 2 Pay Code PayChex Preview Pay Code for Overtime Level 2 Hourly

Wages

Vacation Pay Code PayChex Preview Pay Code for Vacation Hourly Wages

Holiday Pay Code PayChex Preview Pay Code for Holiday Hourly Wages

Sick Pay Code PayChex Preview Pay Code for Sick Hourly Wages

Other Pay Code PayChex Preview Pay Code for Other Hourly Wages

timeQplus Administrator Functions – Export

06-0414-000 Rev. C

Vacation Export as Deduction If checked, export Vacation as a deduction (otherwise as

earning)

Holiday Export as Deduction If checked, export Holiday as a deduction (otherwise as

earning)

Sick Export as Deduction If checked, export Sick as a deduction (otherwise as earning)

Other Export as Deduction If checked, export Other as a deduction (otherwise as

earning)

Sequence The PayChex Preview Import Sequence Number

PayChex IM0007 Import File

timeQplus exports employee profile and time card data to a PayChex IM0007 import file based on values

entered in the following screen. Click the Save button when finished.

PrimePay PrimeLink Export

timeQplus exports employee profile and time card data to a PrimePay PrimeLink import file based on

values entered for the following fields.

Batch Sequence Number The numeric PrimePay PrimeLink Import Batch Number

Overtime Level 1 Pay Code The value to use in the PrimePay PrimeLink import Coded

Hours field for Overtime Level 1 Hours

Overtime Level 2 Pay Code The value to use in the PrimePay PrimeLink import Coded

Hours field for Overtime Level 2 Hours

Vacation Pay Code The value to use in the PrimePay PrimeLink import Coded

Hours field for Vacation Hours

Holiday Pay Code The value to use in the PrimePay PrimeLink import Coded

Hours field for Holiday Hours

Sick Pay Code The value to use in the PrimePay PrimeLink import Coded

Hours field for Sick Hours

Other Pay Code The value to use in the PrimePay PrimeLink import Coded

Hours field for Other Hours

timeQplus Administrator Functions – Export

06-0414-000 Rev. C

Heartland Plus One Fixed Length File

This page describes the file format Heartland PlusOne will accept. If a file does not match these

specifications, it will not import correctly. Imported files should be verified by the payroll user prior to

submitting to assure accuracy.

• Company Identifier – Heartland Company Identifier.

• Pay Codes – Earnings code defined in Heartland Payroll.

• Department code zero len format – specifies the number of leading zeros to include when

exporting department codes.

timeQplus Administrator Functions - Supervisors

06-0414-000 Rev. C

Supervisors

As previously mentioned, timeQplus has two levels of system access: Administrator and Supervisor. Both

types are managed on the Supervisors screen. All users defined as administrators have access to the

Supervisors screen, which allows them to add/delete other administrators and supervisors, reset user

passwords, and edit a supervisor’s list of assigned employees.

To access the Supervisors screen, click the Supervisors button on the left Navigation Bar or click View

on the top menu bar and choose Supervisors.

Managing Administrators and Supervisors

To add a new administrator:

• On the Supervisors screen, click the blank top row under the Login column and enter the

username of the new administrator.

• Check the box under the Administrator column.

• Press the Enter key to save the entry.

To add a new supervisor:

• On the Supervisors screen, click the blank top row under the Login column and enter the

username of the new supervisor.

• Press the Enter key to save the entry.

Note: The default password for a new user will be the same as the Login ID. The system will prompt user

to choose a new password when logging in for the first time.

To delete an administrator/supervisor:

• On the Supervisors screen, click the row displaying the Login ID of the user to be deleted.

• Click the Delete button. Click Yes in the dialog box to confirm deletion. Click No to cancel.

timeQplus Administrator Functions – Supervisors

06-0414-000 Rev. C

An Administrator/Supervisor may change his/her password at any time by logging in and choosing

Change Password from the File menu (on top bar). This will open the Change Password dialog box.

Enter the desired new password in the New Password field as well as in the Confirmation field. Both

entries must be identical. Click the Ok button to change the password. Click the Cancel button to exit.

To reset the password of another administrator/supervisor:

• On the Supervisors screen, click the row displaying the Login ID of the user whose password

you want to reset.

• Click the Reset Password button. Click Yes in the dialog box to reset the password to the user’s

Note: After password reset, the system will prompt the user to choose a new password during next logon.

To edit a supervisor’s list of assigned employees:

• On the Supervisors screen, click the row displaying the Login ID of the supervisor whose

employee list is to be edited.

• Click the Assign/Unassign Employees button. The Employee Assignments screen is

displayed for this supervisor.

• To assign an employee to this supervisor, click the employee’s name under the Unassigned

Employees column and then click the right arrow button to move the employee’s name to the

Assigned Employees column. To assign all employees, click the double right arrows.

• To remove an employee from this supervisor’s assigned list, click the employee’s name under

the Assigned Employees column and then click the left arrow button to move the employee’s

name to the Unassigned Employees column. To remove all employees, click the double left

arrows.

Note: To select multiple employee names, press and hold the CTRL key while clicking each name.

• Click the Save button when done or click Cancel to exit without saving.

timeQplus Administrator Functions – Supervisors

06-0414-000 Rev. C

Supervisor Preferences

The Supervisor Preferences feature allows you to modify your individual preferences for Time Totals

Format and whether you want the Punch Comment dialog box to display by default when you insert

punches through the Punch Editing screen.

To view or change your Supervisor Preferences:

• Log in to the timeQplus software.

• Click File on the top menu bar and choose Supervisor Preferences.

• Select your preference for Time Totals Format. You may choose to display time totals in minutes

or hundredths.

• If you generally like to enter comments when you insert transactions, check the Show Punch

Comment Dialog box. This will cause the Comment dialog box to pop up by default every time

you insert a punch. If you generally do not wish to enter comments when you insert transactions,

uncheck the box.

• Click the Save button when done. To exit without saving change, click the Cancel button.

timeQplus Administrator Functions – Time Clock

06-0414-000 Rev. C

Time Clock

The Time Clock screen allows an administrator to configure and manage Time Clocks that are used with

timeQplus. To access the Time Clock screen, click the Time Clock button on the left Navigation Bar or

click View on the top menu bar and choose Time Clock.

• The Time Clock screen consists of two horizontal tabs: Employees Rights and Device Events, and

three side tabs: Ethernet, Comm Port (which includes RS232 and USB connections), and USB Flash

Drive.

• The Employees Rights tab allows you to assign or un-assign employees to Time Clocks.

• The Device Events tab allows you to view the selected Time Clock event log which includes punches

that were retrieved from the Time Clock.

• Time Clocks that are currently connected via Ethernet to timeQplus are shown with a green dot and

the IP address. A Time Clock that has a red dot is currently not connected or there is some other

network issue at play.

• Time Clocks that are currently connected via Serial [Comm Port] Port are shown with a Proxy IP

address and a COM # and a green dot. If a red dot appears, this Time Clock is no longer connected.

• Times Clocks that require a Flash drive to communicate with the timeQplus system appear on the list

showing the Device #.

• When the mouse pointer is hovered over a listed Time Clock, the user is presented with a small pop-

up that shows what was input in the description field of that Time Clock.

• Select the Ethernet Tab when adding a new network Time Clock or removing a network connected

Time Clock.

• Select the Comm Port side tab when adding a serially connected [Comm Port] Time Clock using an

RS232 [Serial] or a USB using an RS232 adapter connection.

• Select the USB Flash Drive side tab when using a USB flash drive to upload and download data

to/from the computer.

timeQplus Administrator Functions – Time Clock

06-0414-000 Rev. C

Adding an Ethernet Connected Time Clock

• Click the Time Clock button on the left Navigation Bar or click View on the top menu bar and

choose Time Clock. If you’re adding a hand punch, click the Hand Punch button on the left

Navigation Bar or click View on the top menu bar and choose Hand Punch.

• Click the Ethernet tab on the left of Time Clock Manager screen.

• Click the Add Time Clock button. The "Add Time Clock wizard" window will appear.

• Click the Next button. timeQplus will then automatically search your network for time clocks. Only

time clocks that have not been previously added to the software will be listed. If adding a hand

punch, you will need to manually enter the IP address information.

• Select the Time Clock you want to add, and then click the Next button. Note: You can also

manually input the IP address for Time Clocks outside the LAN but can possibly still be accessed

by timeQplus. To initiate this process, check the "I want to set the IP Address manually" box on

lower left, and then click the Next button.

• On the Network Connection window:

o If applicable, enter the Time Clock’s password (the COMM key value assigned on the

Time Clock). A password safeguards the Time Clock against unauthorized network

access.

o Enter a description, which is optional, but recommended. A description such as "Front

Lobby" or "Production Entrance C" can be useful if you have a number of Ethernet

connected Time Clocks.

o Select the Time Clock’s time zone.

o If not adding a hand punch, select a type for the Time Clock: Biometric (Finger), Badge

(Proximity/Barcode/Magstripe), or Facial Recognition.

• Click the Next button when finished.

timeQplus Administrator Functions – Time Clock

06-0414-000 Rev. C

• The "Test Connection" window will appear and indicate if the Time Clock was successfully

connected to timeQplus. If so, click the Next button. If not, click the Back button to review the

setup information on the previous window and try again or click Cancel to exit the wizard and

diagnose the problem.

• When a successful connection is made, the next window will ask if you want to Clear

Transactions (aka punches) on this Time Clock. To clear transactions, check the "Clear device

transactions…" box and click the Next button.

• The "Clear Users" window will ask if you want to delete all existing users on this Time Clock. To

delete all users, click the Clear users button; otherwise, click the Next button to continue.

timeQplus Administrator Functions – Time Clock

06-0414-000 Rev. C

• On the last screen, although not required, performing a manual poll is highly recommended.

Click the Finish button to exit the wizard. The Time Clock should now appear in the list.

timeQplus Administrator Functions – Time Clock

06-0414-000 Rev. C

Adding a Serial Connected Time Clock

Make sure the Time Clock is powered on and you have a USB cable connected correctly to the timeQplus

Server or client PC. Note: Serial connectivity is only available with Biometric (Finger), Proximity, and

Hand Punch Time Clocks.

Step 1 - The Server/PC

• Navigate to Control Panel>Device Manager>Ports

• Locate the Time Clock just connected and note the COM#. This # will be input as the Serial Port

# later.

• Right click on this Time Clock, then select ‘Properties’, then select the ‘Port Settings’ tab

• Select and note for future use the value in the ‘Bits per second’ drop down field. This value will be

input as the Baud Rate later.

Step 2 - The Time Clock

For Biometric or Proximity:

• Press ‘Menu’.

• Select Options and press OK.

• Select Comm Opt and press OK.

• Navigate to and input the desired values for:

o BaudRate

o Dev Num (will be used on the timeQplus Serial Connection setup window)

• The following must be set as noted:

o Ethernet N

o RS232 N

o RS485 N

o USB Y

o COMM Key 0

• Once changes are complete, press ESC and then press OK to save.

Note: For Hand Punch, please refer to the hand punch user manual for configuration instructions.

Step 3 - timeQplus

• Click the Time Clock button on the left Navigation Bar or click View on the top menu bar and

choose Time Clock.

• Click the Comm Port (RS232) tab on the left of Time Clock Manager screen.

• Click the ‘Add Time Clock’ button. The "Serial Connection" window will appear.

timeQplus Administrator Functions – Time Clock

06-0414-000 Rev. C

• The Proxy Server field defaults to the tQp Server machine. Click the search button and

select the proxy server designation for the computer to which this time clock is physically

connected.

• Select the correct values for Serial port, Baud Rate, Device ID, Time Zone, and Time Clock type.

• Enter a description, which is optional, but recommended. A description such as "Front Lobby" or

"Production Entrance C" can be useful if you have a number of connected Time Clocks.

• Click the Next button to continue.

• The "Test Connection" window will appear and indicate if the Time Clock was successfully

connected to timeQplus. If so, click the Next button. If not, click the Back button to review the

setup information on the previous window and try again or click Cancel to exit the wizard and

diagnose the problem.

• When a successful connection is made, the next window will ask if you want to Clear

Transactions (aka punches) on this Time Clock. To clear transactions, check the "Clear device

transactions…" box and click the Next button.

• The "Clear Users" window will ask if you want to delete all existing users on this Time Clock. To

delete all users, click the Clear users button; otherwise, click the Next button to continue

• On the last screen, although not required, performing a manual poll is recommended as noted.

Click the Finish button to exit the wizard. This Time Clock should now be listed on the “Comm

Port (RS232)” tab.

timeQplus Administrator Functions – Time Clock

06-0414-000 Rev. C

Adding a USB Flash Drive Time Clock

This communication type is used when a Time Clock cannot be connected via an Ethernet or a Serial

Connection. It is essentially not connected at all so data is transferred to and from the Time Clock using a

USB flash drive.

• Click the Time Clock button on the left Navigation Bar or click View on the top menu bar and

choose Time Clock.

• Click the USB flash drive tab on the left of Time Clock Manager Screen.

• Click the "Add Time Clock" button and then click "Next". The Remote Time Clock settings can

now be configured.

• Select the Device ID (from the Time Clock)

• Enter a Description (optional but recommended), such as the location of the Time Clock.

• Select the Time Zone.

• Select the Time Clock type: Biometric (finger reader); Badge (proximity/magnetic stripe/barcode

badge reader); Face Recognition.

• Click ‘Next’ and then "Finish".

Assigning/Removing Employees to/from Time Clocks

• Ensure the Employee Rights tab is selected at the top of the screen.

• Click the appropriate tab on the left to select the type of Time Clock communications. (Note: Use

Comm Port for USB-connected Time Clocks.)

• Click to select the desired Time Clock from the list.

• To assign an employee to that Time Clock, click to select the desired employee name in the

Unassigned Employees box.

o Click the right arrow button to move the employee’s name into the Assigned Employees

box.

o To quickly and easily assign all employees to the Time Clock, click the double right arrow

button.

• To remove an employee from that Time Clock (meaning they will no longer be able to use that

Time Clock to punch), click to select that employee’s name in the Assigned Employees box and

then click the left arrow button to move the employee’s name back to the Unassigned Employees

box.

timeQplus Administrator Functions – Time Clock

06-0414-000 Rev. C

• When you have assigned [or removed] all the desired employees on that Time Clock, click the

Save button.

Note: Occasionally, a Time Clock may display a red dot to the left of its name (indicating a loss of

communications). This condition almost always indicates a problem with your company LAN. Normally,

the communications connection would be re-established automatically at the next polling interval, when

the software polls the Time Clocks. If you need to work with a Time Clock before then, such as to assign

employees, press the POLL button. This usually works to re-establish the connection between the

software and the Time Clock. If this fails to solve the problem, it is recommended you contact your

company technical resources for assistance before contacting Acroprint. Contacting Acroprint for this type

of problem may be a fee based communication.

Loading Employee Data onto a USB Time Clock

You can load Employee Data on a Time Clock using one of three methods:

• Method 1: Uploading Employee Information from timeQplus via a flash drive.

• Method 2: Connect the Time Clock via cable (Ethernet or serial) to the timeQplus Server or Client

PC, assign employees, and then, in timeQplus, change the Time Clock to a USB Flash Drive.

• Method 3: Manually adding employees to the Time Clock thru the Time Clock menu.

Methods 1 and 2 are equally preferred ways to load employee information onto a Time Clock. Either

method eliminates the possibility of keying in erroneous information for an employee and is much faster if

you have more than a few employees. In both cases, the employee’s name is displayed when punching.

Method 1 – Uploading Employee Info via Flash Drive

1. Download the employee data from the timeQplus software to a USB flash drive.

a. Insert a flash drive into the PC where the timeQplus server is running.

b. Navigate to the Time Clock screen on the timeQplus software and click the "USB flash

drive" tab.

c. Select the employees you want to assign to the Remote Time Clock and click "Save".

d. If there are multiple USB storage devices connected to the PC, you will need to specify to

which flash drive on which you want to save the employee information. (See image

below)

e. Click the "Save to USB" button.

Two or four files will be downloaded to the Flash Drive. Two if you are not using Work Codes, four if

you are. The files are: user.dat, template.dat, globalworkcodes.dat, and userworkcodes.dat.

Note: For the Face Verify Time Clock, you will see ssrface.dat instead of template.dat.

IMPORTANT!

• Each time you click "Save to USB"; all assigned employees will be downloaded to the Flash

Drive even if they have already been downloaded previously.

• If you want to assign only certain employees to a given Time Clock, you will need to delete

any existing files on the Flash drive before saving the next group of employees to the Flash

drive for the next Time Clock.

2. After downloading all employee information, connect the flash drive to the Time Clock.

3. Press the "Menu’ button.

timeQplus Administrator Functions – Time Clock

06-0414-000 Rev. C

Note: For a facial recognition Time Clock, skip to step 6.

4. Select ‘PenDrive Mng’ and press ‘OK’.

5. Select ‘UpLoad User’ and press ‘OK’. You will see ‘Copy Data Suc‘ when upload is complete.

6. Press Menu > Dn/Upload > Upload User. You will see ‘Upload Successfully’ when upload is

complete.

7. Remove flash drive. Now employees can punch as needed.

Method 3 - Manually Adding Employees to the Time Clock:

You can add employees directly to the time clock. You must make sure that the User ID of each

employee matches that employee’s User ID in the timeQplus software.

If you add employees via this method, a punch will show the employee User ID #. The employee name

will not be displayed when punching.

Downloading Punch Data from a Time Clock to a flash drive

• Connect your flash drive to your Time Clock. For facial recognition time clocks, skip to step 3.

• On the Time Clock, press Menu> PenDrive Mng> Download AttLog. Skip to step 4.

• On the facial recognition Time Clock, press Menu > Dn/Upload > Download Transactions.

• Once the Time Clock has copied all punch data to the Flash Drive, a message, "Copy Data Suc"

or "Download Successfully" will appear on the Time Clock display indicating that the transfer of

punch data was successful.

• Remove the Flash Drive.

A single flash drive can be used with multiple Time Clocks since each transaction data file is identified

with the device number of the Time Clock. For example, 1_attlog.dat, 2_attlog.dat, etc.

All transactions will be downloaded including any that existed before the last download, assuming they

have not been manually deleted.

To delete transactions from the Time Clock (only after downloading to a flash drive and uploading to your

timeQplus Server):

• On face recognition time clocks, press Menu > Data Mgt. > Delete Transactions.

• On badge or biometric time clocks:

o Press Menu.

o Select ‘Options’ and press ‘OK’.

o Select ‘System Opt’ and press ‘OK’

o Select ‘Adv Option’ and press ‘OK’

o Select ‘Del AttLogs’ and press ’OK’

Uploading Punch Data from the USB flash drive to the timeQplus server

Note: Time Clock data can only be uploaded to the timeQplus Server and not to any client PCs.

• Connect the flash drive to the PC.

• Navigate to the Time Clock screen on the timeQplus software and click the "USB flash drive" tab.

• Click "Import USB drive" or alternatively from the timeQplus Systems Utility Screen, you can click

"timeQplus Import USB drive".

Note: If there are multiple Flash Drives with punch data connected to the PC, please take care to

select the one with the data you want for this import.

• Select the appropriate flash drive and click ‘OK’. The Import Tool screen will appear:

timeQplus Administrator Functions – Time Clock

06-0414-000 Rev. C

• To view transaction data before importing, highlight a data file and click ‘View file transactions’.

• To import transaction data, highlight the file(s) you wish to import and click ‘Import selected

files…’ To select multiple files, press and hold the CTRL key while clicking the file name(s).

• After the import is complete, you will be prompted to backup the file(s). Click ‘Yes" to create a

backup file on the flash drive as an archive; otherwise, click ‘No’.

• You will then be prompted to delete (from the flash drive) the file(s) that were just imported. Click

‘Yes’ to remove the files from the flash drive; otherwise, click ‘No’ to finish.

Poll and Update

The Polling process performs the following actions in timeQplus:

• Polling retrieves punches that have been made on any connected Time Clock and updates the

timeQplus server with punches since the last Polling event.

• Polling will clear the Time Clock of all punches after retrieval. A visual record of punches will,

however, remain on the ‘Device Events’ screen on the Time Clock tab.

• Polling sends the timeQplus server time and date to any connected Time Clock.

• Removes from connected Time Clocks employees that are ‘marked for deletion’, i.e., employees

whose templates have been removed from the timeQplus software.

The Update process performs the following actions in timeQplus:

• A polling event is the first action launched when you start the Update process. Polling is done to

obtain an accurate In/Out status for employees assigned to the Time Clock.

• Updates a connected Time Clock with employee name changes.

• Updates the hours worked for the current pay period for each employee assigned to a connected

Time Clock. If an employee is assigned to multiple Time Clocks, each Time Clock is updated.

• Refreshes the current Work Code list to update all additions and deletions.

To schedule the automatic poll and update of all Time Clocks:

• From the File menu, choose System Utilities.

• Click the timeQplus Settings tab.

• Enter a value for the polling interval. The default is 60 minutes, with a 10 minute minimum

allowed.

• Set the update time. The default is 12am.

• Enter the frequency of the update. The default is 24 hours, with a 1 hour minimum allowed.

• If applicable, set the polling interval, update time, and frequency for hand punch time clocks.

timeQplus Administrator Functions – Time Clock

06-0414-000 Rev. C

• Click Ok when done or Cancel to exit.

To manually poll or update a single connected Time Clock:

• Navigate to the Time Clock screen and click the appropriate tab on the left.

• Click a Time Clock in the list to highlight and then click the Poll Clock button.

• Click a Time Clock in the list to highlight and then click the Update Clock button.

To manually poll or update multiple connected time clocks simultaneously:

• Click the Multi Time Clock Poll & Update button located at upper right of Time Clock screen.

• Check the box to the left of the Time Clocks you wish to include (identified by IP address).

• Select either Poll or Update and then click Next to proceed.

Changing Time Clock Connection Types

Use caution when making changes to the Time Clock configuration.

Incorrect settings can cause the software to be unable to

communicate with the Time Clock.

In certain instances, it may be necessary to change an Ethernet or Serial connected Time Clock to a USB

Time Clock. Some reasons for this action:

- A previously installed Ethernet or serial connected Time Clock is being moved to a location

without a network or serial connection.

- Communication to an existing Ethernet connected Time Clock has been lost and the user needs

to get the transaction data from the clock.

To change a Time Clock’s connection type from Ethernet or Serial to USB:

• Select the Time Clock and click the Time Clock Details button. The Time Clock Details screen

will appear.

• Click USB flash drive and then click Save.

timeQplus Administrator Functions – Time Clock

06-0414-000 Rev. C

This Time Clock is now moved from the Ethernet or Comm Port connections tab to the USB Flash Drive

connection tab. All employees assigned to the Time Clock will still remained assigned.

Note: If you want to assign additional employees, you will have to add them to the Time Clock manually

or via a Flash Drive.

To change a Time Clock’s connection type from USB to Ethernet or Serial:

• Select the desired USB Flash Drive Time Clock and click "Time Clock Details".

• Check "Network Device" or "Serial Device".

o When selecting "Network Device", make sure you input the correct IP Address and

Password (if applicable).

o When selecting "Serial Device", make sure you enter the correct Serial Port number and

Baud Rate

• Click the Save button when finished.

The Time Clock is now moved from the USB Flash Drive tab to the Ethernet or Comm Port connection

tab.

timeQplus Administrator Functions – Time Clock

06-0414-000 Rev. C

Copying Multiple Finger Templates from One Time Clock to Another

timeQplus is capable of storing only one (1) primary finger template for each employee; however the

TQ600B Time Clock is capable of storing up to ten (10) finger templates for each employee.

If you wish to enroll multiple finger templates for employees on more than one Time Clock, you will need

to download the finger templates from a Time Clock to a USB flash drive then upload the finger templates

to one or more additional Time Clocks.

The process is as follows:

1. Insert a flash drive into the Time Clock that has the multiple finger templates.

2. Select Menu, then PenDrive Mng and then press OK.

3. Select DwnLoad User and then press OK. You will see “Copy Data Suc” displayed once

download is complete.

4. Press ESC until you see the Welcome screen.

5. Remove the flash drive.

6. Insert the Flash Drive into the next Time Clock.

7. Select Menu, then PenDrive Mng and then press OK

8. Select UpLoad User and then press OK. You will see “Copy Data Suc” displayed once upload is

complete.

9. Press ESC until you see the Welcome screen.

10. Remove the Flash Drive.

11. Test an employee with multiple Fingers to see if all finger templates were uploaded successfully.

12. Repeat steps 6 -11 for all remaining Time Clocks.

timeQplus Administrator Functions – Hand Punch

06-0414-000 Rev. C

Hand Punch

A new install key is required to be able to see the Hand Punch button and screen unless it was supplied

as a new purchase.

A Hand Punch time clock can be connected to the timeQplus software via an Ethernet or Serial

connection only. Select the appropriate tab on this screen when adding a hand punch.

An employee cannot use a UserID and Password combination to punch. For this reason, only employees

with an enrolled hand template can be seen on the Hand Punch screen.

Once an employee’s hand template is enrolled, the employee will be placed in the Assigned Employees

area for that Hand Punch time clock.

When assigned, an employee can be unassigned and will appear in the Unassigned Employees area.

timeQplus Administrator Functions – System Utilities

06-0414-000 Rev. C

System Utilities

Date Tools

The Data Tools tab of the System Utilities screen allows an administrator to manage important

configuration options and troubleshoot the timeQplus database, as well as upgrade the number of

employees allowed by the system.

• Select System Language – Click the appropriate button to select the desired system language.

The default is English. Note: Changing the language setting will require restarting the system.

• Initialize Database – Clear all information from the database and invoke the setup wizard.

WARNING! Use of this option will delete all existing information, including employee

timeQplus Administrator Functions – System Utilities

06-0414-000 Rev. C

profiles and punch data unless the Administrator performing this operation chooses to

keep existing employees in the database.

• Initialize Users – Deletes all users (both Administrators and Supervisors) defined on the

Supervisors tab except the default admin login ID. The password for the admin login ID is reset to

“admin”.

• Import QuickBooks – Import employees from QuickBooks.

• Import timeQplus or Attendance RX – When upgrading from Attendance RX or timeQplus

Version 2 the Previous and Current pay period data from the old system will be imported into the

new timeQplus Version 4.xx database. The archive databases will remain on, and be accessible

to your computer where the current time and attendance applications are installed.

• Backup – Backs up the current timeQplus database to a SQL Server database

• Restore – Restores the most recent database stored in SQL Server to timeQplus.

• Upgrade – Allows you to install an increased number of employees or additional features that

you can configure in your timeQplus software. Requires a purchased upgrade from Acroprint.

• View Event Log – Lists the date and time of critical events such as pay period rollover and setup

rules changes.

• Upload Data – Automatically uploads a copy of your database to Acroprint Customer Support

group to assist you and the Acroprint technician in resolving issues.

• Realign Transactions – If a punch is recorded at the Time Clock, but the Time Clock is not

polled until the system has rolled to the next pay period, some punches could be associated with

the incorrect pay period. Use this feature to move the misaligned punch(es) to the appropriate

pay period.

• timeQplus Debug Tool – Use this tool to troubleshoot communications issues with your

timeQplus Time Clock devices and validate data that is stored on the Time Clocks.

• timeQplus Import USB drive – When a Time Clock is installed as USB flash drive which has no

wired data connection to the server, an Administrator takes a USB drive to the Time Clock and

retrieves the Punch data. The punch data is then uploaded to the timeQplus database by

connecting the USB drive to the computer which contains the timeQplus server/database.

• timeQplus Import Tool – Use this tool to import Time Clock transactions from log files stored in

the timeQplus database.

Use extreme caution when changing settings on the Data Tools tab.

Changes made on this screen can have a significant impact on the

database and operations of timeQplus.

timeQplus Administrator Functions – System Utilities

06-0414-000 Rev. C

timeQplus Settings

The timeQplus Settings tab of the System Utilities screen allows an administrator to enable and

configure the automatic polling and update of all time clocks in addition to resetting the position of the

virtual clock.

Note: The settings on the timeQplus Settings screen apply to all online Time Clocks.

• Enter the desired Polling Interval (in minutes). This determines how often the system will poll the

Time Clock(s) and bring new punch data in to the central database. The default is every 60

minutes. When setting the Polling Interval, you should keep in mind employees cannot clock

In/Out while the Time Clock is being polled. Also, polling too frequently may affect the availability

of computer system resources.

• Enter the desired Update Time for employee status on the Time Clocks. For TQ600 clocks, this

is the time of day at which the system will determine and set the correct IN/OUT status of each

employee, and also calculate and store in the Time Clocks the number of hours worked this pay

period for each hourly employee. The system will also "push" to the Time Clocks any employee

name changes that have occurred since the last status update.

• Enter the Frequency (in hours) at which employee statuses should be updated. The default is

once every 24 hours.

• Click the Reset Virtual Clock Position button to center the Virtual Clock on the currently active

display. This will take affect the next time the Virtual Clock is launched.

06-0414-000 Rev. C

timeQplus Supervisor Functions

This chapter provides detailed information on timeQplus functions specific to the supervisor role. It

contains the following sections:

¾ timeQplus Navigation Bar

¾ Employees

¾ Messages

¾ Punch Editing

¾ Reports

¾ Time Clock

timeQplus Supervisor Functions

06-0414-000 Rev. C

timeQplus Navigation Bar

The timeQplus Navigation Bar for supervisors allows them to view/edit employee information, approve

time cards and TimeSlips, and view/print reports.

To see the Navigation Bar, double click the timeQplus icon on your desktop. Ensure that you are

connecting to the correct server and then enter your Supervisor Login and Password.

Click the buttons on the left Navigation bar to access the Supervisor functions:

• Employees Manage employee information and shift assignments

• Messages View and Edit your Employee Messages

• Punch Editing View and Edit Employee Time Cards & Time Slips

• Reports Print or Preview Reports

• Time Clock Update Time Clocks

timeQplus Supervisor Functions

06-0414-000 Rev. C

Employees

On the Employees screen, supervisors can view/edit employee information or assign Work Codes to

employees. This applies to assigned employees only.

To access the Employees screen, click the Employees button on the left Navigation Bar or click View on

the top menu and choose Employees.

To edit an employee’s information:

• From the Employees screen – On the Employees screen, simply type the updated information

directly into the appropriate field and press ENTER.

• From the Employee Profile screen – Click anywhere on the row containing the employee to be

edited. Click the Detail button to launch the Employee Profile screen, which allows additional

employee information to be recorded and saved. Click Save when done or click Cancel to exit

without saving. Please reference the Managing Employees section in the timeQplus Administrator

Functions chapter for more information.

timeQplus Supervisor Functions

06-0414-000 Rev. C

Work Codes

To edit an employee’s list of work codes:

• On the Employees screen, click the row containing the employee’s name.

• Click the Work Codes button to display the Employee Work Codes screen.

• From the “Choose a Pay Period” drop down list, select the pay period for which the work code

assignments should apply. The selection defaults to the Current pay period.

• To assign a work code(s) to this employee, click a single work code or, to select multiple work

codes, press and hold the CTRL key while clicking each code under the Unassigned Work

Codes column. Click the right arrow button to move the work code(s) to the Assigned Work

Codes column. To assign all work codes, click the double right arrows.

timeQplus Supervisor Functions

06-0414-000 Rev. C

• To remove a work code(s) from this employee’s assigned list, click a single work code or, to

select multiple work codes, press and hold the CTRL key while clicking each code under the

Assigned Work Codes column. Click the left arrow button to move the work code(s) to the

Unassigned Work Codes column. To remove all work codes, click the double left arrows.

When a work code(s) is unassigned and the chosen pay period is Current, you will be asked if

you want to unassign only from future pay periods:

o Click No if the work code(s) should be unassigned from both the current and future pay

periods.

o Click Yes if the work code(s) should be unassigned starting with the next pay period moving

forward. An expiration date (the start date of the next pay period) will be displayed for each

unassigned work code. When the next pay period begins, the work code will be

automatically removed from this employee’s assigned work codes list.

• Click Next to proceed with selecting the employee’s default work code.

timeQplus Supervisor Functions

06-0414-000 Rev. C

• On the Default Work Code screen, select the work code that should be the employee’s default.

Check the “Select a different default work code for the future pay period” box to choose a different

default work code for the next pay period. Please note that this option is only visible when the

chosen pay period is Current.

Note: Only the employee’s assigned work codes are populated in the Default Work Code drop

down list. If the employee has no assigned work codes, then the Default Work Code drop down

list will contain all available work codes.

• After selecting a default work code, click Next. For work codes that were unassigned, the

software will then determine if there are existing transactions in the chosen pay period that

use those work codes. If so, an error message will be displayed indicating which work codes

are in use. In order to continue, you will need to click the Back button to reassign the work

code(s) or click the Cancel button to exit. No work code can be unassigned if it is being used

by at least one transaction.

timeQplus Supervisor Functions

06-0414-000 Rev. C

• If there are no errors, the “Save Changes on Time Clocks” screen is displayed. The work

code changes will be sent to each time clock to which the employee is assigned. The Result

column will indicate whether the time clock was updated successfully.

Messages

The Messages screen allows supervisors to display employee-specific messages to their assigned

employees when they punch at a PC on the Virtual Clock.

To create or edit employee-specific messages:

Enter employee-specific messages in the Message field next to the employee’s name. This message

will appear once on this employee’s PC screen after the next punch.

timeQplus Supervisor Functions

06-0414-000 Rev. C

Punch Editing

On the Punch Editing screen, supervisors have access to all of the same functionality as

administrators. The only difference is that supervisors have access to their assigned employees only.

Please reference the Punch Editing section in the timeQplus Administrator Functions chapter for more

details.

Reports

The Reports screen allows supervisors to generate reports to preview, print, or export. Supervisors

have access to the reports listed below and, for reports involving employee data, can view data for their

assigned employees only. The Reports screen also allows supervisors to search for past and present

(assigned) employees using the Employee Search button (located in the upper right corner of screen).

The search results will contain data on when an employee was added to and, if applicable, removed

from the timeQplus software.

• Employee Profiles • Approaching Overtime

• Shifts • Daily Totals By Day

• Time Card • Daily Totals by Employee

• Holidays • Work Codes Total By Work Code

• Hours Summary • Work Codes Totals By Employee

• Raw Transactions • Missing Punches

• Who’s IN, Who’s OUT • Employee Default Work Codes

• Time Card Approvals • Punch Comments By Employee

Please reference the Reports section in the timeQplus Administrator Functions chapter for detailed

information on generating and exporting reports.

timeQplus Supervisor Functions

06-0414-000 Rev. C

Time Clock

The Time Clock screen allows supervisors to send employee changes to all time clocks. During the

update process, a poll of each time clock is also performed and an accurate IN/OUT status is obtained

for each employee.

Click the Update Time Clocks button to initiate an update of all time clocks. Once complete, the Result

column will indicate whether each time clock was successfully updated. If a failure is observed, please

contact your timeQplus Administrator for further assistance.

06-0414-000 Rev. C

Virtual Clock

This chapter describes the Virtual Clock functions. It contains the following sections:

¾ Login to Virtual Clock

¾ Submit Employee TimeSlip

¾ IN/OUT Board

timeQplus User Guide – Virtual Clock

06-0414-000 Rev. C

Click the Virtual Clock icon on your Desktop:

Enter employee UserID and Password and then press the Enter key or click the Ok button. The

following window will appear:

• To punch, select a work code from the ‘Work code’ drop down list (if applicable) and then click the

Punch button. If a work code is assigned, the ‘Work code’ field will be pre-populated with the

employee’s default work code; otherwise, it will be blank.

• To view the time card for the previous pay period, click View the Previous Time Card.

• To view the time card for the current pay period, click View the Current Time Card.

timeQplus User Guide – Virtual Clock

06-0414-000 Rev. C

Submit Employee Time Slip

This feature is for use by salaried employees for whom overtime pay is not applicable. Access to this

feature requires a User ID and Password assigned by a timeQplus Adminstrator/Supervisor.

Employees may enter a batch of transactions as a single TimeSlip. This can be useful for employees who

wish to submit vacation or holiday hours in advance, or employees who track their own hours and submit

their time at the end of each pay period.

Each TimeSlip applies to a single pay period. Employees may submit multiple TimeSlips to record

transactions in Current, Previous or Future pay periods.

Note: A salaried employee who punches into timeQplus will show a red check mark under the column

heading "@" on the day(s) at least one punch was made. This feature may be useful to validate a salaried

employee was on site on a given date.

To Access Your TimeSlip:

• Double click the Virtual Clock icon on your desktop.

• Enter your UserID and Password and then press the Enter key or click the Ok button.

• Click Submit Employee TimeSlip (located on top menu bar).

• Choose the Pay Period you would like to view from the ‘Pay Period’ drop-down list.

To Edit Your TimeSlip:

Once you have accessed the desired TimeSlip, you can edit the totals for any day which are listed on the

left side of the screen.

• Locate the row corresponding to the date you want to edit.

• Click to select the field in that row under the category you want to edit.

• Type over the existing value with your new total and press the Enter key on your computer

keyboard, or click on another row. Enter the elapsed time in hours and minutes.

• The Pay Period Totals will be updated to reflect your revised entry.

To Submit Your TimeSlip:

• You may select another pay period, add more transactions, or delete transactions until you are

satisfied with the contents of each pay period's TimeSlip.

timeQplus User Guide – Virtual Clock

06-0414-000 Rev. C

• When you have finished entering hours and are ready to submit your TimeSlip(s), click the

Submit button to submit to the Supervisor. Click the Cancel button to exit the process without

submitting.

IN/OUT Board

The Employee IN/OUT Board displays the most recent known status of all employees. Employees who

are clocked in appear in the left pane while employees who are clocked out appear in the right pane.

Note: Since Time Clocks are polled at set intervals, the information on the IN/OUT board will not be

displayed in real time. The board will display the employees’ status as of the most recent Time Clock

polling cycle. You can force an IN/OUT board update by going to the Time Clock screen and pressing the

Poll button.

06-0414-000 Rev. C

Glossary

The timeQplus system is a Windows-based PC application designed to offer simple yet effective

employee time and attendance management.

Active Transaction

Any time card entry that exists in any active (previous, current, or future) pay period.

Transaction types include: Punch, VAC, SIC, HOL, OTH, FMLA, REG

Approaching OT

The Approaching Overtime report lists employees whose total time worked places them at risk of incurring

overtime for the pay period

Auto Lunch After

The number of hours of an employee being clocked in without clocking out for lunch, after which the

system assumes the employee forgot to clock out and automatically subtracts the Lunch Duration from

the employee’s total hours worked.

Average Totals By Employee

The Average Totals By Employee report shows the weekly and monthly time averages (worked and time

off) for each employee for the specified date range. If an employee has any missing punches, an

asterisk (*) is display next to that employee’s name.

California Overtime

California Overtime Rule settings as of the release of this product are as follows:

Daily Weekly

Overtime Level 1 Threshold: 8 hours 40 hours

Overtime Level 2 Threshold: 12 hours 168 hours (disabled)

7th Day Overtime: ENABLED

Daily Overtime Threshold

The Daily Overtime Thresholds specify the amount of time worked in a day, after which, overtime will

begin to accumulate. Any time worked after the overtime-level 2 threshold will be accumulated in overtime

2. Any time worked after the overtime level 1 threshold but not over the level 2 threshold will be

accumulated in overtime 1. Note: Leave the threshold at 24 hours if you only pay overtime based on a

40-hour week only.

The default value for Daily overtime threshold is 24 Hours.

Daily Totals by Day

The Daily Totals by Day report shows the time totals for each employees grouped by day for the selected

pay period or pay period range.

Daily Totals by Employee

The Daily Totals by Employee report shows time totals for each day grouped by employee for the

selected pay period or pay period range.

Day Change Offset

By setting a Day Change Time, the user can adjust the time of day that one day changes to the next to a

time other than midnight.

(For more information, please see Day Change Offset)

Glossary

06-0414-000 Rev. C

Edit Time Totals

The Edit Time Totals feature allows an employee's total time accumulations to be adjusted without

altering the punch information. Adjustments can be made, for both current and the previous pay periods,

to regular, overtime 1, and overtime 2-hour accumulations.

Employee Badge Number

This number can be up to 10 digits, must be unique among employees and can range between 1 and

9999999999. This must be set to the same number as the employee’s badge used at the badge reader

time clock.

Employees By Supervisor Report

The Employees By Supervisor report lists for each supervisor his/her assigned employees.

Employee Default Work Codes

The Employee Default Work Codes report lists each employee along with his or her assigned default

work code. If the employee does not have an assigned work code, the first work code in the global work

code list will be displayed.

Employee Name

The employee name is associated with a particular badge number. The employee name will show up in

reports. Reports can be sorted alphabetically. Enter last names first if reports need to be sorted by last

name.

Employee Number

This is the number to be associated with an employee. This is a payroll number.

Alert: This number is not encrypted by the system. For security reasons,

we strongly suggest you do not use employees’ Social Security numbers

as their employee numbers in the timeQplus software.

Employee Profile Report

The Employee Profiles report lists all employees in the timeQplus system. It displays each employee’s

last name, first name, middle initial, badge, employee number, export id, user id, and shift number.

Employee Shift Assignment

The shift number defines which set of shift and lunch rules are to be associated with a particular

employee.

Employee UserID

This number must be unique among employees and between 1 and 9999. This number is used to clock in

and out at the PC.

Enter Current Pay Period Start Date

The first item required is the start date of your company's current Pay Period.

Export ID

The Employee Alternate Export ID is a 48-character alphanumeric field that can be used to identify

employees when exporting to OEM applications.

Holiday Report

The Holiday Report lists all holidays that have been entered into the timeQplus system as of the selected

pay period.

Glossary

06-0414-000 Rev. C

Hours Summary Report

The Hours Summary report lists hours worked by regular and overtime hours for a specified pay period or

pay period range. This report can be generated for an individual employee, a specific shift, or all

employees. If an employee has any missing punches, an asterisk (*) is display next to that employee’s

name.

Lunch Duration

The standard number of minutes for lunch that will be subtracted from time worked totals. Lunch Duration

is ignored if the employee's lunch rules are disabled.

Lunch End

This is the latest time of day at which an employee should punch back in from lunch. The system may

adjust an employee's IN from lunch punch to make sure that a full Lunch Duration is taken.

Lunch Start

This is the earliest time of day at which an employee can punch out for lunch. The system may adjust an

employee's out to lunch punch to make sure that a full Lunch Duration is taken.

Max Time On Clock

Max Time on Clock specifies how long an employee can be punched in before assuming that the

employee forgot to punch out.

(For more information, please see Max Time on Clock)

Missing Punches Report

The Missing Punches report lists all employees with missing punches for the selected pay period.

Next Pay Period Start Date

(Required For Semi-Monthly Pay Periods only)

When using Semi-Monthly Pay Periods, each month contains two Pay Periods. After selecting a current

pay period start date and semi-monthly pay period type, the user must also specify the start date of the

NEXT pay period in order to establish the two days of each month that mark the beginning of each Semi-

monthly pay period.

Overtime Thresholds

Overtime thresholds specify how employee hours will be divided among Regular, Overtime1 and

Overtime2 during the course of each day and of each week.

For more information on overtime calculations in general, see Overtime Thresholds.

Pay Interval Rounding

The timeQplus Pay Period Setup Wizard allows the user to specify how time intervals will be rounded.

timeQplus supports rounding to the nearest one(1), five(5), six(6), ten(10) or fifteen(15) minute interval.

(For More information, Please see Pay Interval Rounding)

Pay Period Type

The timeQplus supports WEEKLY, BI-WEEKLY, SEMI-MONTHLY, and MONTHLY Pay Periods.

Punch Comments By Employee Report

The Punch Comments report lists by employee all comments and their associated punches for the

selected pay period.

Glossary

06-0414-000 Rev. C

Raw Transactions Report

The Raw Transactions report lists each transaction in the selected pay period. It allows you to see how

and when transactions were entered into the system.

Rules Setup Report

The Rules Setup report lists all of the Setup rules plus all users, both Administrators and Supervisors for

the selected pay period.

Shift Dock

The maximum number of minutes an employee will lose from time worked totals for punching IN late or

punching OUT early.

Shift Grace

The number of minutes after the Shift Start Time or before the Shift Stop Time in which employee

punches will be treated as if they had occurred exactly on the Shift Start and Stop Times.

Shift Round

The number of minutes before the Shift Start Time or after the Shift Stop Time in which employee

punches will be treated as if they had occurred exactly on the Shift Start and Stop Times.

Shift Start Time

The time of day employees in this shift are scheduled to begin work.

Shift Stop Time

The time of day employees on the shift are scheduled to stop working.

Shifts Report

The Shifts Report displays the Shift rules and Lunch rules for each shift, including holiday settings.

Supervisors By Employee Report

The Supervisors By Employee report lists for each employee his/her assigned supervisor(s).

Time Card Approval Report

The Time Card Approvals report displays a two-column listing of employee names, with those whose time

cards have been approved listed on the left and those whose time cards have not been approved listed

on the right. The Time Card Approval feature can be turned on or off by an Administrator using the Setup

screen.

Time Card Report

The Time Card Report lists an employee's transactions and accumulations of time worked. This may be

for a selected pay period or pay period range. The report may be for one employee, employees on a

specific shift, or for all employees.

Weekly Overtime Threshold

The Weekly Overtime Thresholds specify the amount of time worked in a week, after which, overtime will

begin to accumulate. If an employee's Regular hours for the week reach the Weekly Overtime Level 1

Threshold, all subsequent hours worked for the week will begin to accrue to Overtime Level 1. Once an

employee's combined Regular hours have exceeded Weekly Overtime 1 Threshold, AND the employee's

combined Regular and Overtime 1 hours for the week have reached the Weekly Overtime Level 2

Threshold, all subsequent hours worked for the week will accrue to Overtime Level 2. To disable either

Weekly Overtime 1 or Weekly Overtime 2, set the Overtime Level 1 or Overtime Level 2 threshold to zero

(0), or set either Overtime Threshold to a large value that can never be reached.

Glossary

06-0414-000 Rev. C

The default value for Weekly Overtime Threshold Level 1 is 40 hours. The default value for Weekly

Overtime Threshold Level 2 is 168 hours (disabled, logically unreachable).

Who's In and Who's Out Report

The Who's In, Who's Out report lists the IN/OUT status of all employees. This function is disabled on the

original default installations. If Time Clocks are used, the In/Out status will be delayed until the Time

Clocks are polled by the software.

Work Codes Totals By Employee

The Work Codes Totals By Employee report shows the time totals for each work code grouped by

employee for the selected pay period or pay period range.

Work Codes Totals By Work Code

The Work Codes Totals By Work Code report shows the time totals for each employee grouped by work

code for the selected pay period or pay period range.

TimeQplus User Guide_Rev C Time Qplus TQ600 Tqplus Guide En

Navigation menu

Versions of this User Manual:

Views

Navigation