Dongboshi tech R1 electric skateboard User Manual Owners Manual V6

Download:
Mirror Download [FCC.gov]
Document ID	3786872
Application ID	zPK+8HgtY69w+Up2pfvrgg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	300.94kB (3761779 bits)
Date Submitted	2018-03-19 00:00:00
Date Available	2018-03-19 00:00:00
Creation Date	2018-01-05 02:57:06
Producing Software	Mac OS X 10.9.5 Quartz PDFContext
Document Lastmod	2018-03-09 10:16:02
Document Title	Owners Manual V6
Document Creator	Word
Document Author:	Ben Forman

READ BEFORE RIDING
Always wear a helmet. Other safety gear such as gloves, pads,
closed-toe shoes, long sleeves, and long pants are strongly
advised.
Be aware of other cars and vehicles, as they can kill. Always ride
defensively when in the presence of other vehicles. Be aware of
local laws that govern proper usage of your board on public
roads, bike paths, sidewalks, or other places you may ride.
Braking downhill on a full battery can cause a board shutdown.
Internal circuitry will allow for some braking on a downhill at full
charge, but this braking is limited. To avoid this be sure to ride
on flats or uphill to drain the battery before attempting a
downhill after a full charge.
Your board can lose power and brakes at any moment due to
radio interference, a dead remote battery, downhill overcharging
on a full battery, and other factors. Only ride your board at
speeds and on hills where you’d be comfortable without power
and brakes.
Acceleration in Pro mode is rapid and may be dangerous.
Hills and high speed can be very dangerous. Be sure to start slow
and remain extra careful in these conditions, even if you are an
experienced rider.
WARNINGS
Always wear a helmet when riding. Never ride in water, wet
surfaces, in the rain, slippery or uneven surfaces, steep hills,
traffic, cracks, train tracks, gravel, rocks, or any obstacles that
could cause loss of traction. Avoid riding at night, areas with
poor visibility, and narrow spaces.
Whenever you ride a Riptide Electric Skateboard you risk death
or serious injury from loss of control, collisions, and falls. To ride
safely you must read and follow all warnings and instructions in
this manual.
Do not ride the Riptide Electric Skateboard in environments, on
inclines, or at speeds where you would not be safely in control of
an unpowered skateboard. In the event of wireless interference
or battery fault, you may need to rely on skating techniques like
foot braking or sliding to a stop.
Avoid water. Riding in wet conditions or through puddles can
damage the board’s electronics and cause the board to lose
power or stop suddenly, causing a risk of loss of control or falls.
Damage to the board due to water exposure is not covered
under warranty.
Keep your fingers, hair, and clothing away from belts, motors,
wheels and all moving parts. Do not open or tamper with
electronics housings. Electric shock is possible and this also voids
the warranty.
1. Remote Components
2. Board Components
3) Pre-Ride Checklist
•
Always wear a helmet. Other protective
equipment such as gloves, pads, closed-toe
shoes, long sleeves, and long pants are
recommended.
•
Ride in an open, flat area without foot or car
traffic for your first rides. Also make sure you are
in Beginner Mode (Section 11) when you are
learning.
•
Read through the warnings on the first two
pages of this manual.
•
Avoid environments that can cause loss of
control including loose gravel, water, hills,
cracks, train tracks, traffic, low light, or poor
visibility.
•
Check and tighten all hardware.
4) Riding Stance: Regular vs. Goofy?
Riding “Regular” means you stand with your left foot
forward, towards the nose of the board. Riding “Goofy”
means you stand with your right foot forward. How do
you know which one you are? Think about a tug-of-war –
whichever foot you would put forward when competing in
a tug of war to brace yourself, that is the foot you should
put forward when riding. Test and see what works best for
you.
Regular
Stance
Goofy
Stance
5) Power the Remote On/Off
Press the Remote Power Button, found on the underside
of the Remote. The Signal Indicator LED on the side of
the remote will illuminate once it is turned on. When
connected to the board, the Signal Indicator LED will
blink and the Battery Level Indicator LEDs will illuminate
to display the board's battery level.
6) Power the Board On/Off
Underneath the handle,
press and release the
Board Power Button. It
will illuminate once the
board is on. When
connected to the
remote it will blink.
7) Pairing the Remote
When you turn on the Remote and Board for the first time
they should pair automatically. When paired, the Signal
Indicator on the Remote will blink green and the Battery
Level Indicator LEDs will illuminate to display the board's
battery level. Engaging the Thumb Throttle will spin the
motors. If the Remote and Board do not properly pair:
Step 1: Turn on the Board and Remote.
Step 2: Press and hold the Board Power Button for five
seconds until it begins blinking.
Step 3: As seen to the
right, press the Remote
Pairing Button using a thin
object such as a pen or
paperclip.
The Board Power Button
and Signal Indicator will
begin flashing when they
are paired.
8) Riding the Riptide
Extend your thumb on the
Thumb Throttle to accelerate.
Pull back on the Thumb
Throttle to brake.
• Always move the Thumb Throttle in small increments.
• Bend your knees and keep a wide stance.
• Don’t put your rear foot too far back onto the tail, as
this may cause you to lose your balance.
• Lean forward when accelerating, lean back when
braking.
10
Accelerating
First, bend your knees and shift your weight forward
towards the board’s nose. Gently extend your thumb to
push the Thumb Throttle away from you until the motors
begin to engage. The further you roll the Thumb Throttle
forward, the faster the Riptide Electric Skateboard will go.
At any time you can release the Thumb Throttle to coast
or roll it backwards to brake.
Braking
When you are ready to brake make sure to bend your
knees and shift your weight to the rear of the deck. Gently
roll the Thumb Throttle downwards until you feel the
board’s motors begin to actively slow the board down.
For additional braking power roll the Thumb Throttle
downward at a faster rate, but be sure your stance is
prepared so you don’t lose your balance and have to step
off the board.
11
Coasting
To coast, simply release the Thumb Throttle. This will cut
power to the motors though you still will feel added
friction from the drive train.
Reverse
To switch the board into Reverse,
press the Reverse Button located
on the side of the Remote below
the row of LEDs. Now, roll the
Thumb Throttle up to go in
reverse and down to brake
(slowing down your reverse
speed). The board must be
stationary to change between
forward and reverse. If you press
the Reverse Button while moving,
the board will be unresponsive to
Remote input until either the
board comes to a stop or the
Reverse Button is pressed again
to re-engage power in the
forward direction.
12
9) Check the Board Battery Level on the Board
100% 75% 50% 25%
When fully charged, all four LEDs on the Board Battery
Meter will illuminate. As the battery capacity diminishes,
fewer LEDs will remain lit. When battery level is critically
low, the board will make an audible beeping and
eventually cut power to the motors. Braking will remain
enabled.
10) Check Battery Levels on the Remote
Remote
Battery
Remaining
Board
Battery
Remaining
Green: OK
Red: Charge
Remote
75% - 100%
50% - 75%
25% - 50%
1 blinking LED: <25%
When looking at the Remote’s LEDs, the single LED to the
left shows the Remote’s battery level. The three LEDs to
the right show the Board’s battery level.
13
11) Change the Riding Mode
Beginner
Toggle Switch at top
Top Speed: Min
Acceleration: Slow
Eco
Toggle Switch in middle
Top Speed: Max
Acceleration: Slow
Pro
Toggle Switch at bottom
Top Speed: Max
Acceleration: Fast
You can change the riding mode at any time, even when
moving. In close quarters or crowds of people, “Pro”
mode may be too sensitive. Try shifting to a lower Riding
Mode for more refined control at low speed.
Note: To go in Reverse, see Section 8.
14
12) Charging the Board
When properly
charging the LED
on the charger will
turn red.
When charging is
complete this LED
will turn green.
13) Charging the Remote
Use the included Micro-USB cord.
When the Remote is charging
properly an LED will turn red
under where the lanyard
connects. This LED will turn
off when the Remote is
fully charged.
15
w w w. r i d e r i p t i d e . c o m
instagram.com/rideriptide
youtube.com/rideriptide
facebook.com/rideriptide
t w i t t e r. c o m / r i d e r i p t i d e
FCC Caution：
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 5.6-c015 81.157285, 2014/12/12-00:43:15
Format                          : application/pdf
Creator                         : Ben Forman
Title                           : Owners Manual V6
Create Date                     : 2018:01:05 02:57:06Z
Creator Tool                    : Word
Modify Date                     : 2018:03:09 10:16:02+08:00
Metadata Date                   : 2018:03:09 10:16:02+08:00
Producer                        : Mac OS X 10.9.5 Quartz PDFContext
Document ID                     : uuid:9d33ce51-c6d7-4c77-bae7-8f1966ae20a6
Instance ID                     : uuid:f9aefb40-15c8-44e2-bf2b-7fd3ce8da3de
Page Count                      : 17
Author                          : Ben Forman

EXIF Metadata provided by EXIF.tools