Dongguan Digital AV Technology WUS14 WIFI Module User Manual WUS AC14 V 01

Download:
Mirror Download [FCC.gov]
Document ID	3163311
Application ID	m7Ly+MW6LBHPI2ekHTY9BA==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	51.61kB (645187 bits)
Date Submitted	2016-10-14 00:00:00
Date Available	2016-10-25 00:00:00
Creation Date	2016-10-14 09:43:32
Producing Software	Acrobat Distiller 10.1.0 (Windows)
Document Lastmod	2016-10-14 09:43:32
Document Title	Microsoft Word - WUS-AC14 User Manual V.01
Document Creator	PScript5.dll Version 5.2.2
Document Author:	ls

WUS‐AC14USER MANUAL
CONTENTS
Introduction ......................................................................................................................................... 3
Specifications ....................................................................................................................................... 3
Wi‐Fi driver installation – Linux OS...................................................................................................... 4
Regulatory Warning Statements ......................................................................................................... 5
Integrator Instructions ........................................................................................................................ 7
 INTRODUCTION
The wireless dual‐band WUS‐AC13 USB interface adapter delivers powerful wireless AC technology to your
host devices. Simplyplug the adapter into an available USB interface,throughtthe wafer connector,and then
connect to a 2.4GHz or a 5GHzwireless network to access a secure, high‐speed Internet connection atup to
300Mbpsor up to 433Mbps respectively. With the integrated dual‐band technology, Wi‐Fi interference will be
reduced to maximize throughput for a faster data connection.
 SPECIFICATIONS
Item
Descriptions
Wi‐Fi:
IEEE 802.11a/b/g/n/ac standards
External
Interfaces
Supports 2.4GHz or 5GHz for dual‐band wireless operation
2x2 MIMO with two spatial streams with a data rate of up to 866Mbps (AC900)
Antenna: U.FL connectors& Stamp hole
Connectors and
2 x U.FL connectors for Wi‐Fi
Buttons
Power Supply
3.3 VDC from USB Interface
Dimensions
Module Size: 40.5mm x 23mm
Environmental
Operating Temperature: 0°Cto 50 °C
Regulatory
FCC ,IC,CE,TELEC
Certification
voltage regulator
MT7662U DC 3.3V input via Wi‐Fi TX mode: 800mA
Wi‐FI RX mode: 350mA
 WI‐FI DRIVER INSTALLATTION – LINU
UX OS
he folder wheere the driver file is located.
In the terminal and navigate to th
For example, cd CE__MT7662U_CFG80211.
driver: make
Build d
1. Install the driveer onthe OS with
w administraator permissio
on: sudo make
e install
2. Reemove the USSB adapter and
d then re‐inseertthe USB adapter to activvatethe newly installed drivver.
 REGULATORYY WARNINGG STATEMEN
NTS
Federral Commun
nication Commission In
nterferencee Statementt:
This deevice complies with Part 15
5 of the FCC Rules. Operatio
on is subject to
t the followin
ng two conditions: (1)
This deevice may nott cause harmffulinterferencee, and (2) thiss device must accept any interference received,
includiing interferen
nce that may cause
undesireed operation.
This eq
quipment has been tested and found to comply with the
t limits for a Class B digittal device, purrsuant to
Part 15
5 of the FCC Rules.
These limits aredesiggned to provid
de reasonable protection aggainst harmfu
ul
interfeerence in a ressidential instaallation. This equipment
generates, uses and can radiaateradio frequ
uency
energyy and, if not in
nstalled and used in accordance with thee instructions,, may cause haarmful interfeerence to
radio ccommunicatio
ons.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radioor television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference byone of the following
measures:
‐ Reorient or relocate the receiving antenna.
‐ Increase the separation between the equipment and receiver.
‐ Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
‐ Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority tooperate this equipment.
This transmitter must not be co‐located or operating in conjunction with any other antenna or transmitter.
FCC ID Label on the final system must be labeled with “Contains FCC ID: 2AGM4‐WUS14”
Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and
are safe for intended operation as described in this manual. The further RF exposure reduction can be
achieved if the product can be kept as far as possible from the user body or set the device to lower output
power if such function is available. The Device should at least 20cm separation distance ayway from the
human body
Industry Canada statement:
This device complies with RSS‐210 of the Industry Canada Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Cedispositifestconforme a la norme CNR‐210 d’Industrie Canada applicable aux appareils radio exempts de
licence. Son fonctionnementestsujetaux deux conditions suivantes: (1) le dispositif ne doit pas produire de
brouillageprejudiciable, et (2) cedispositifdoit accepter tout brouillagerecuycompris un brouillage susceptible
de provoquer un fonctionnementindesirable.
 INTEGRATOR INSTRUCTIONS
Part Number: WUS‐AC14
FCC ID: 2AGM4‐WUS14
IC: 20960‐WUS14
1. Additional Regulatory Conformance Testing and/or Submissions
Required by the Integrator
The global modular certifications apply to radio conformance for the Module only.
The OEM integrator is responsible for additional system‐level EMI/EMC and Product
Safety testing and certification that applies in the U.S. and other countries to the host
system containing the Module. This includes, but is not limited to, Federal
Communications Commission (“FCC”) Part 15 Class B Digital Emissions, and ETSI EN
301 489‐17.
These system‐level EMC tests are to be done with the Module installed and
included in the scope of the submission.
Some of the countries for which modular certifications are provided require
additional submissions, authorizations or import permission by the system‐vendor or
importer. The integrator is responsible for these additional actions.
By way of example, the OEM integrator must take additional action for radio
certification in these countries:
Malaysia
Each importer/distributor needs to file for import permission
Singapore
Recommend use of importer’s own local radio dealer number
Israel
Additional approval certificate required for importer
Indonesia
Certificate B is required for each importer
China
Modular approval not accepted. Requires system approval
Brazil
Tablets require system level SAR evaluation and submission to Anatel.
Philippines
Modular approval not accepted. Requires system approval
Vietnam
Modular approval not accepted. Requires system approval
Indonesia
Modular approval not acceped. Requires system approval
Modular radio certification is not possible in some countries. For such countries, OEM integrators
must ensure radio certification for the end system is obtained, before placing the product on the
market.
2. ALLOWABLE ANTENNAS TO USE WITH THE RADIO MODULE
The module is certified to support following external PCB antennas with IPEX connector.
Table 1 Allowed Maximum Gain (dBi), Including Antenna Cable Loss
WARNING:
Use of other antenna types or the same type of external antenna with higher gain
is not allowed without additional testing and appropriate FCC approval.
3. ANTENNA PLACEMENT INSIDE THE HOST SYSTEM AND RF SAFETY
The FCC and other countries’ regulatory bodies impose strict conditions and limitations on
the RF exposure levels of end products. Acceptable RF exposure levels for this Module
depend on transmit power, the location of the transmitting antenna(s) inside the host
system, the expected separation of the transmitting antennas to the end user, as well as if
there is/are collocated RF transmitter(s) in the same host system. OEM integrators must
take great care to ensure each host system complies with the applicable RF exposure
requirements.
4. SIMULTANEOUS TRANSMISSION WITH OTHER INTEGRATED OR PLUG‐IN RADIOS
The FCC imposes conditions and limitations when additional radio(s) are co‐located in the
same host system as the Module with capability to transmit simultaneously. The detailed
rules from the FCC are described in various Knowledge Database publications that may be
found using the instructions below. Co‐locating other radios such as an integrated or plug
in Wireless WAN/cellular radio with the module requires additional evaluation and
possibly submission for authorization from the FCC.
Because the rules are highly dependent on the characteristics of the particular radios that
are co‐located and simultaneously transmitting, the OEM integrator should seek guidance
from a knowledgeable test lab or consultant to determine if additional testing and FCC
certification is required. In this case, failure to evaluate and follow the required FCC
procedures will invalidate the FCC certification of the Module and end system.
To download the FCC rules for collocated radios:
1. https://apps.fcc.gov/oetcf/kdb/index.cfm
2. Enter 616217 in the ‘publication number’ search box
3. Download latest applicable version of KDB 616217 document.
For expert advice regarding collocation rules, we recommend you contact an
FCC‐approved
Telecommunication Certification Body (“TCB”)::
4. https://apps.fcc.gov/oetcf/kdb/index.cfm.
5. Choose your country and or state from the pull‐down list.
6. Scroll through the search results and choose a TCB contact from which to seek advice.
5. MODULE MAY NOT BE INSTALLED BY END USERS
FCC rules require this Module to be installed in host systems at the factory by the OEM
integrator. Thus, end users of the system may not install the Module. Therefore, the host
product user instructions must not advise the end user on how to access or remove the
Module. Additional FCC authorization/filing is needed to allow end user installation of radio
modules.
10
6. REQUIRED LABELING ON THE OUTSIDE OF THE HOST
NOTE:
5.1
Explanatory text in red font must not be included in the final label.
FCC
The FCC requires a label on the outside of the host system visible to the end
user. Example wording is:
Contains:
FCC ID: XXX‐XXXXXXX
IC: XXXXX‐XXXXXX
(Replace X’s with actual IDs found in section 2).
The FCC requires a logo signifying emissions compliance on the outside of the host system.
Additional options are available for placement of the FCC label on the host. Please refer
to the FCC Knowledge Database KDB784748 found at
https://apps.fcc.gov/oetcf/kdb/index.cfm.
NOTE:
The Integrator is responsible to perform FCC Part 15 Class B digital emissions
testing on the end system with the radio Module installed. The FCC logo below should not
be affixed unless the OEM integrator has obtained the necessary Part 15 approval, e.g.,
self‐declaration of conformity.
11
If the host system is approved to FCC Class B digital emissions limits under a grant of
certification issued by a TCB, the FCC ID number shown on the grant should be used on the
label instead of the FCC logo below.
5.2
European Community R&TTE
The European Community R&TTE Directive requires the CE Marking shown below on
theoutside of the host AND on the outside of the shipping container/packaging:
The European Community R&TTE Directive also requires the following note to consumers
on the outside of the shipping container/packaging:
Important Notice: This product is a Radio LAN
device operating in 2.4 & 5 GHz bands for
Home and Office use in the E.E.A. States with
restrictive use are highlighted in grey. Refer to
user documentation for details.
AT
BE
CH
CY
CZ
DE
DK
ES
FI
FR
GB
GR
EE
HU
IT
IE
IS
LI
LT
LU
LV
MT
NL
NO
PL
PT
SE
SI
SK
NOTE:
The Integrator is expected to translate the text in this Section into the appropriate
local languages for the European countries in which the product will be marketed or sold.
5.3
FCC labeling on the Module
12
The Integrator must ensure that the FCC ID (as indicated in section 2) is affixed on the
Module along with other country certification numbers and logos as described herein.
NOTE:
The Module ODM may affix regulatory labeling at time of Module manufacturing.
However, the OEM Integrator must ensure the Module label is complete, correct and
applicable for all countries to which the host system is to be imported, marketed, or sold.
RF Exposure Information and Statement
This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance of 20 cm between the radiator and
your body. This transmitter must not be co‐located or operating in conjunction with any other antenna or
transmitter.
RF exposure assessment has been performed below to prove that this unit will not generate the harmful EM
emission above ther reference level as specified in EC Council Recommendation (1999/519/EC). The
Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the
device and the human body. To maintain compliance with RF exposure requirement, use product that
maintain a 20cm distance between the device and human body.
The FCC and other countries’ regulatory bodies impose strict conditions and limitations on the RF exposure
levels of end products. Acceptable RF exposure levels for this Module depend on transmit power, the location
of the transmitting antenna(s) inside the host system, the expected separation of the transmitting antennas
to the end user, as well as if there is/are collocated RF transmitter(s) int the same host system. OEM
integrators must take great care to ensure each host system complies with the applicable RF exposure
requirments.
13

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : ls
Create Date                     : 2016:10:14 09:43:32+08:00
Modify Date                     : 2016:10:14 09:43:32+08:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - WUS-AC14 User Manual V.01
Creator                         : ls
Producer                        : Acrobat Distiller 10.1.0 (Windows)
Document ID                     : uuid:3001c333-1518-4dac-8f2a-02ea8b92dc03
Instance ID                     : uuid:979f03d8-9d83-4546-adb1-3efec6efe4b1
Page Count                      : 13

EXIF Metadata provided by EXIF.tools