Dongguan Taide BT225 Wireless Speaker User Manual awsp 03
Dongguan Taide Industrial Co., Ltd. Wireless Speaker awsp 03
User Manual
4 in
5.6 in
back
front
wireless speaker
included
• Bluetooth Speaker
charging
• Plug micro end of charging cable into back of speaker DC 5V
• Plug USB end of charging cable into a DC 5V USB power supply
• Charging is complete when red light turns o
• Full charge requires approximately 3-4 hours
indicators
• Solid Red - Charging
• No Red Light - Fully charged
Flashing White - Pairing mode
Solid White - Bluetooth connected
• Ascending Tones - Power on
• Descending Tones - Power o
• Three Rapid Tones - Ready to pair
• Single Chime - Paired
• Two Rapid Dings - Low battery
• Quick Ascending Tone - Max volume
• Quick Descending Tone - Min. volume
charge input
hold for
power
aux portmode:
bluetooth/
aux
play/
pause
answer/
end calls
decrease volume/
hold previous track
increase
volume/
hold
next
track
pairing
• Power ON speaker
Flashing white light
• Use Bluetooth settings on your phone to pair with HEYDAY SPEAKER 02
Flashing white light turns solid - Pairing successful
phone calls
• Answer/End Incoming calls - Press phone button
• Refuse Incoming Call - Press and hold phone button
• Dial Last Incoming Call - Press phone button twice
aux/line in
• Insert 3.5mm audio cable (not included) into speaker AUX port
• Insert opposite end of audio cable into the music source
need some help?
Can’t get it to pair? Not accepting phone calls? Just have a question?
call us at: x-xxx-xxx-xxxx e-mail us at: xxxxxxx@xxxx
safety
• Do not use near any water source
• Do not modify or repair this device
• Do not use in high temperatures or extreme weather
• Do not use chemical detergents to clean your device, use a soft dry cloth
troubleshooting
• Speaker not working normally:
Power OFF/ON to reset
• Can’t turn speaker on:
Recharge battery and try again
• Can’t charge speaker:
Ensure power supply works, is 5V > 1A, and connectors are not damaged
• No sound or speaker does not show as an available device on phone:
Ensure speaker is not paired to another phone. Enter Bluetooth settings on
connected phone and unpair device, follow pairing instructions on desired device.
FCC ID: XXXXX-XXXXX Model: awsp-03 SN:T0318 Input: 5V Max .4A Made in China
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not
cause harmful interference, and 2) this device must accept interference received, including interference that may cause
undesired operation. Warning: Changes or modications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Target Corp. Mpls. MN, 55403 Phone: xxx-xxx-xxxx
FCC ID: OYC-BT225 Model: BT225 SN:T0318 Input: 5V Max .4A Made in China