DoorKing Door King Replacement Convenience Open Board Manual 1473 065 F 3 18 0
User Manual: DoorKing DoorKing Replacement Convenience Open Board Manual Owner's Manual
Open the PDF directly: View PDF 
.
Page Count: 18
| Download | |
| Open PDF In Browser | View PDF |
Installation Replacement Convenience Open Board Manual For Pre-2016 Convenience Open Operators ONLY Use this manual for circuit board 1473-010. 1473-065-F-3-18 For Pre-2016 Convenience Open Models: 1600, 1602, 1603, 6100, 6300, 6500, 9150 and 9310 Operators ONLY Replacement Board for 2340-010 Convenience Open Board 610 0 CONFOR ANSI/UL MS TO CAN/CSA CERTIFI -325 63 ED VEHICUC22.2 TO CLASS LAR NO. 53382 247 GATE MODEL OPERA SERIAL TOR HP VOLTS WA RN AMPS MAX GATE LOAD DoorKing PHASE 60 Hz , Inc., Inglewoo 160 d, CA 1 J1 115 VAC INPUT RESET IN G MOVI SERIONG GATE Operate US INJURCAN and free gate Y ORCAUS of only Do people when or not allow E DEATH and gate operate area children obstructi Do gate. is ons.in sight pathnot stand to play while in in gate Read gate gate area path owner’s is moving. or walk manual through and safety instructio ns. 00 CONFOR ANSI/UL MS TO CAN/CS CERTIF -325 A IED VEHIC C22.2 TO NO. CLASS ULAR 247 53382 GATE MODEL OPERA SERIAL TOR HP VOLTS AMPS MAX PHASE GATE DoorKin LOAD g, 60 Hz Inc., Inglewo od, CA HEART BEAT 160 3 P1 1 2 3 4 5 6 7 8 9 10 RUN TIME CLEAR STAT 00 65 BATT STAT TRICKLE CHARGE STAT 1473-010 160 2 WAR ON NI MOV SERI ING OUS 1 2 3 4 ON TIMER AUTO OPEN MOTOR DIR AC ON ACT LIMIT SW2 NG GAT Operat INJUE CAN and e free gate RY CAU of only Do OR people when SE or not allow DEAT and gate operate area childre obstruc H Do gate. is tions. n to in pathnot stand sight play while in in gate Read gate gate area path owner’ is moving or s manua walk . throug l and h safety instruc tions. CONFO ANSI/U RMS TO L-325 CAN/CCERTI SA FIED VEHI C22.2 TO CULA NO. 53382 247 R GATE OPER ATOR CLASS MODE L SERIA 0 915 HP L VOLTS AMPS MAX PHASE GATE DoorK LOAD 60 ing, Hz Inc., Inglew ood, CA 10 93 Date Installed: Installer/Company Name: Operator Circuit Board Serial Number and Revision Letter: Phone Number: Leave Manual with Owner Copyright 2018 DoorKing, Inc. All rights reserved. UL 325 Compliant TABLE OF CONTENTS 1473 CONVENIENCE OPEN BOARD INTRODUCTION 1473 Board Overview DIP-Switches SPECIFIC GATE OPERATOR INSTALLATION 6100, 6300 Swing Gate Operator(s) 6500 Swing Gate Operator(s) 9150 Slide Gate Operator(s) 9310 Slide Gate Operator(s) 1601, 1602, 1603 Barrier Gate Operator(s) Replacement Parts for Convenience Open System 2 2 3 4 4-5 6-7 8-9 10-11 12-13 14 DoorKing, Inc. reserves the right to make changes in the products described in this manual without notice and without obligation of DoorKing, Inc. to notify any persons of any such revisions or changes. Additionally, DoorKing, Inc. makes no representations or warranties with respect to this manual. This manual is copyrighted, all rights reserved. No portion of this manual may be copied, reproduced, translated, or reduced to any electronic medium without prior written consent from DoorKing, Inc. 1473-065-F-3-18 1 1473 CONVENIENCE OPEN BOARD INTRODUCTION Use this manual when replacing a 2340-010 convenience open board on an existing PRE-2106 gate/barrier operator ONLY. The 2340-010 control board is obsolete and cannot be replaced. IMPORTANT • The 1473 convenience open board is a REPLACEMENT board for an existing 2340 convenience open board ONLY. • The convenience open system cannot provide continuous gate operation during a power outage. • Operation of this system is limited to cycling the gate to the open (up) position ONE TIME ONLY. • The convenience open system requires testing on a monthly basis to insure the batteries are fully charged and that the system is operational. • The convenience open system uses two 12-volt, 3.0 amp-hour gel-cell batteries. These batteries should be replaced every two years on average, or sooner if required. A reminder beeper has been designed in the 1473 board, see below. • Batteries are affected by temperature. Cold temperatures will reduce the effectiveness of the batteries and the backup system. High temperatures will result in a shortened battery life. • Batteries are not covered under warranty. • This system cannot be used with SLIDE gate operators that are configured in the Fail-SECURE mode. • If your access control system requires 100% power backup and continuous operation when primary (AC) power has failed, a power inverter / backup system, such as DoorKing’s Model 1000 can be purchased separately. 1473 Board Overview Reset Button Press to reset board. 115 VAC Input (J1) J1 Connect to gate operator’s terminal inputs as shown on following pages, REQUIRED. DO NOT connect to 208/230 VAC input. RUN TIME CLEAR STAT Blinking:Indicates board is operating normally. DIP-Switch 4 MUST be OFF to adjust 4-41 sec. Clockwise increases the run time, Counter-clockwise decreases the run time. See next page. Clear Stat Button Press and hold the CLEAR STAT button for 4 secs clears the battery replacement reminder counter and resets the beeping indication. BATT STAT TRICKLE CHARGE Beeper STAT A beep every 20 seconds indicates that battery replacement is needed. Press and hold the CLEAR STAT button to reset the battery reminder beeping and clear the counter. 1473-010 ON 1 2 3 4 TIMER ON 2 HEART BEAT LED Run Timer Adjustment P1 1 2 3 4 5 6 7 8 9 10 Note: See pages 4-13 for your specific gate operator(s) terminal connection. RESET HEART BEAT 10-Pin Terminal (P4) COMMON-1 Common for open, radio receiver or open limit switch. Note: Radio receiver cannot be connected when the 1473 is installed in a 1601, 1602, 1603, 6500 or 9310 gate operator. OPEN INPUT (LIMIT)-2 Open input. (Open limit switch for 1601, 1602, 1603, 6500, 9310). RADIO POWER-3 24 -Volt power for radio receiver (9150 and 6100/6300 gate operators only). Radio gets powered by operator batteries during power outage. ACTIVATION OUTPUT-4 Radio relay activation or switch closure across terminals 1 and 2 will send an activation signal out of this terminal to the gate operator single-button activation input. 24 VAC INPUT-5-Not Used 24 VAC COMMON-6 BATTERY POSITIVE INPUT-7 BATTERY NEGATIVE INPUT-8 DC MOTOR POSITIVE OUTPUT-9 DC MOTOR NEGATIVE OUTPUT-10 115 VAC INPUT AUTO OPEN MOTOR DIR AC ON ACT LIMIT SW2 1473 DIP-Switches See next page. Battery LEDs BATT STAT LED 2 Blinks: Replace batteries. 3 Blinks: Battery level is too low. 4 Blinks: Batteries are not connected. 5 Blinks: Bad battery. 6 Blinks: Battery charge current exceeds maximum, possible shorted cell. TRICKLE LED Steady Green LED: Battery is fully charged and a trickle charge is being used to maintain a full charge. CHARGE LED Steady Yellow LED: Battery is being bulk charged. Blinking Yellow LED: Battery is 90% of a full charge. STAT LED 3 Blinks: Extreme temperature, charging suspended. 1473-065-F-3-18 1473 DIP-Switches Switch Function 1 Auto Open Operation After Power Outage Setting Description OFF (Manual Mode) Residential application: For 6100/6300 or 9150 operators ONLY. Gate will remain closed after a power outage. A radio receiver input or switch closure device across terminals 1 and 2 will run the operator motor’s “Run Time” set on the 1473 to the open position. (1601, 1602, 1603, 6500 or 9310 models will NOT function in this mode). ON (Auto Mode) Apartment complexes, gated communities, etc.: Gate will automatically run the operator motor’s “Run Time” set on the 1473 OR use the operator’s limits to the open position. This switch MUST be ON for 1601, 1602, 1603, 6500 and 9310 operators. 2 Motor Dir Motor Direction OFF Sets the opening direction (up) of the gate. If the gate won’t open after a power outage, reverse this switch. ON 3 AC on ACT Restore Power Operation OFF Physical Input Required: An input (push button, loop, radio receiver, etc.) is required to return the gate to normal operation again. 4 ON Auto: a 1-second pulse is automatically sent to the gate operator input to restore normal operation again. Timer-OFF Timer-OFF 1473 “run timer” is used and MUST be adjusted. For 9150 OR 6100/6300 gate operators ONLY. Limit-ON Operator Type Limit-ON Operator limits are used to stop gate at open/up position. For 1601, 1602, 1603, 6500 and 9310 operators ONLY. Switch 1 OFF: Manual Mode - Residential ONLY Manual mode is designed for residential applications only, for 6100/6300 or 9150 operators ONLY. (1601, 1602, 1603, 6500 or 9310 models will NOT function in this mode). DIP-Switch 1 OFF: the 1473 will not open the gate if a power failure occurs until a manual input is received, either from a wired push button or RF transmitter. This allows the gate to remain closed upon a loss of AC power, but provides a method to open the gate when desired. In manual mode, the STAND-ALONE RF receiver is connected directly to the 1473 control board and is powered by this board. During normal daily operation, when the relay in the radio receiver closes (a valid transmitter code has been received), this “signal” is passed through the 1473 control board’s terminal 4 that has been wired to the gate operator’s main control board terminal open input. If a power failure occurs, the radio receiver is powered from the operator batteries maintaining its operation. When a valid RF transmitter code is received under these conditions, the 1473 control board signals the operator DC motor to run for the set “Run Time”. A push button device wired to terminals 1 and 2 on the 1473 control board will also open the gate after a power outage has occured. Note: The RF transmitter will open the gate when using a stand-alone type receiver. If the gate system uses a receiver that outputs the transmitter code in weigand format to a phone entry system (such as DoorKing’s 1833, 1835, 1837 or 1838), then opening the gate from the RF transmitter under power outage conditions will NOT be possible when the system has been set up this way. Switch 1 ON: Auto Mode - Apartment Complexes, Gated Communities, Etc. DIP-Switch 1 ON: the 1473 will automatically open the gate or raise the barrier arm approximately 2-3 seconds AFTER loss of AC power occurs. Automatic mode is always used for gates in general access applications such as gated communities, apartment complexes, etc. Automatic mode MUST be used with 1601, 1602, 1603, 6500 and 9310 operators. Switch 2: Operator Opening Direction The operator MUST open (Barrier arm goes UP) when power outage occurs. If the operator doesn’t open during a power outage, reverse this switch’s position. Switch 3: Restarting Operator AFTER AC Power Has Been Restored DIP-Switch 3 ON: Automatically “Re-keys” the gate operator to establish normal operation again. DIP-Switch 3 OFF: Requires a “physical input” (push button, loop, radio receiver, etc.) BEFORE the gate operator will resume normal operation again. Switch 4: Using 1473 “Run Timer” or Operator’s Limits for Open Position DIP-Switch 4 ON: Uses the gate operator LIMITS to stop the gate/arm at the open position. For 1601, 1602, 1603, 6500 and 9310 operators ONLY. Not for use on 6100/6300 or 9150 operators. DIP-Switch 4 OFF: Uses the 1473 RUN TIMER setting (4 to 41 secs) to stop the gate at the open position. For 6100/6300 or 9150 operators ONLY. Not for use on 1601, 1602, 1603, 6500 and 9310 operators. 1473 “Run Timer” Description RUN TIME Used for 6100/6300 or 9150 gate operators ONLY. The “run timer” sets the amount of time that the operator’s DC motor will run after it gets activated by the 1473 circuit board. Adjust the run timer so that the gate opens to approximately six inches shy of the full open position and stops. DO NOT allow the DC motor to run beyond the full open position and slip the operator clutch or stall the DC motor. Damage to the circuit board may result from this. Clockwise adjustment increases the run time, counter-clockwise adjustment decreases the run time. Note: The run timer is not used when the 1473 circuit board is installed in the 1601, 1602, 1603, 6500 or 9310 operators. 1473-065-F-3-18 3 SPECIFIC GATE OPERATOR INSTALLATION Select YOUR specific gate operator(s) installation on this page or the following pages. 6100, 6300 Single Swing Gate Operator 610 0 63 00 Single Operator Control Board White Blue 1 1 2 3 4 5 6 7 8 9 10 115 VAC INPUT BATT STAT TRICKLE 1 2 3 4 ON AUTO OPEN MOTOR DIR AC ON ACT LIMIT SW2 CHARGE STAT ON Dry Contact 13 20 4502-010 DATA 12 P 14 15 SW1 NO NC SW2 1 2 3 4 5 6 7 8 Operator DC Motor Red Connect a normally open device to terminals 1-2. This allows another method to open the gate when a power outage occurs if the auto-open mode is NOT used (1473 DIP-Switch 1 is OFF). 13 14 15 16 17 18 19 KEY SWITCH 11 ON Black Dry Contact 10 1 2 3 4 5 6 7 8 HEART BEAT RUN TIME 1473 Control Board Push Button Manual Mode White Adjust Run Timer N.O. This radio receiver will work during normal daily operation as well as during a power outage. The radio receiver will be powered from the operator’s batteries during a power outage. 9 10 11 12 ON RESET 1473-010 Com Stand-Alone 3-Wire Radio Receiver Manual Mode Green TIMER CLEAR STAT Emergency Vehicle Access 6 7 8 9 2 DANGER J1 P1 24 Volt Relay Com 1 HIGH VOLTAGE! 2 3 4 5 Operator DC ON/OFF Power Switch • Operator will function in either manual or auto open mode (1473 DIP-Switch 1). Red/White • 1473 DIP-Switch 4 MUST be OFF (Timer) and run timer MUST be adjusted. 12 V 3 Amp/Hr – + Red Operator Batteries 12 V 3 Amp/Hr – + Black/White 4 1473-065-F-3-18 6100, 6300 Bi-Parting Swing Gate Operators 610 0 Operator Chassis Ground Connect a normally open device to terminals 1-2 of the PRIMARY 1473 ONLY. This allows another method to open the gate when a power outage occurs if the auto-open mode is NOT used (1473 DIP-Switch 1 is OFF). Blue Green White Red Blue 1 Gray to #2 - not required if the auto open feature is turned on. 1 2 3 4 5 6 7 8 9 10 Yellow Green Brown CLEAR STAT BATT STAT SW1 SW2 1 2 3 4 5 6 7 8 ON White HEART BEAT Green to #2 - not required if the auto open feature is turned on. 12 V 3 Amp/Hr Secondary Operator Terminal Green Com 1 2 3 4 5 6 7 8 9 10 CLEAR STAT TIMER 1 3 4 5 6 7 Not Used 8. GRAY Common Pulse 2 12 VAC 7. ORANGE 6. BROWN 5. YELLOW 24 VAC 4. PURPLE 115 VAC Neutral 115 VAC Motor 2 Green 8 Green See above Optional - Gray Orange Brown HEART BEAT RUN TIME Black Secondary DC Motor 12 V 3 Amp/Hr Red – + Secondary DC ON/OFF Power Switch Yellow RESET 1473-010 – + 1 2 3 4 – + ON Red BATT STAT TRICKLE CHARGE STAT ON AUTO OPEN MOTOR DIR AC ON ACT LIMIT SW2 Adjust Run Timer Secondary 1473 Control Board Red 2. BLUE White 115 VAC Motor Operator Chassis Ground 1. RED 115 VAC INPUT 12 V 3 Amp/Hr Blue Blue – + J1 115VAC Input 3. WHITE 1 2 3 4 ON RUN TIME Orange 1 2 3 4 5 6 7 8 NO NC DoorKing Interconnection Cable Sold Separately SECONDARY operator’s 1473 board’s 115VAC Input MUST interconnect to PRIMARY main terminals #2-White & #3-Blue. Red Red/White Black/White 1473-065-F-3-18 15 Primary Operator Control Board Red/White • 1473 DIP-Switch 4 MUST be OFF (Timer) and run timer MUST be adjusted. 14 20 Primary DC ON/OFF Power Switch • Operator will function in either manual or auto open mode (1473 DIP-Switch 1). DATA ON RESET 1473-010 13 Operator LED 12 Purple TRICKLE CHARGE STAT ON AUTO OPEN MOTOR DIR AC ON ACT LIMIT SW2 13 14 15 16 17 18 19 Secondary KEY EY S SWITCH H 11 White TIMER This radio receiver will work during normal daily operation as well as during a power Com outage. The radio N.O. receiver will be powered from the operator’s batteries Push Button Manual Mode during a power outage. Dry Contact Dry Contact Primary Operator LED 9 Stand-Alone 3-Wire Radio Receiver Manual Mode Primary DC Motor Primary Batteries 4502-010 10 Black Black/White DANGER White Blue 115 VAC INPUT 6 7 8 9 Purple 2 Secondary Operator Motor Terminal 10 11 12 Emergency Vehicle Access Adjust Run Timer 1 HIGH VOLTAGE! 2 3 4 5 Wht J1 P1 24 Volt Relay Com Primary 1473 Control Board Red 63 00 12 V 3 Amp/Hr Secondary Batteries 5 6500 Single Swing Gate Operator 65 00 • Operator will ONLY function in auto open mode (1473 DIP-Switch 1 ON). • 1473 DIP-Switch 4 MUST be ON (Limit). This allows the 1473 to use the 6500’s magnetic limit for the gate OPEN position. Orange Limit Sensors Plug REV SENSE PRIMARY REVERSE LOOP DANGER 20 4405-010 HIGH VOLTAGE! 16 17 18 19 20 115 VAC INPUT 13 14 15 1473-010 AUTO OPEN MOTOR DIR AC ON ACT LIMIT SW2 1 2 3 4 TIMER 10 11 12 NC NO ON ON 8 BATT STAT 7 TIME DELAY CLEAR STAT 6 STAT 6 7 8 9 RESET POWER REV SENSE SECONDARY DO NOT use Run Timer 5 J1 1 2 3 4 ON SW2 4 4 CHARGE 3 TRICKLE 2 RUN TIME 1 P1 LMT HEART BEAT 2 3 4 5 2 1 2 3 4 5 6 7 8 9 10 Orange Green Blue EXIT LOOP 1 SW1 1 2 3 4 5 6 7 8 P8 ON P2 White White Black Red Single Operator Control Board Operator DC Motor Red/White – + – + Black/White Red 12 V 3 Amp/Hr Operator Batteries 6 12 V 3 Amp/Hr Operator DC ON/OFF Power Switch 1473-065-F-3-18 6500 Bi-Parting Swing Gate Operators Primary Operator Control Board 65 00 Orange Limit Sensors Plug REV SENSE SECONDARY REV SENSE PRIMARY REVERSE LOOP DANGER Spare Limit COM 6 7 8 Orange Purple Gray Limit 5 Brown 4 Yellow 3 White 2 Red 1 Blue Blue Blue 1473-010 White Primary DC ON/OFF • Operator will ONLY Power function in auto open mode Switch (1473 DIP-Switch 1 ON). White Primary Operator 8-Pin Secondary Interface Terminal • 1473 DIP-Switch 4 MUST be ON (Limit). This allows the 1473 to use the 6500’s magnetic limit for the gate OPEN position. Primary Batteries SECONDARY operator’s 1473 board’s 115VAC Input MUST interconnect to PRIMARY main terminals #19-Blue & #20-White. Green AUTO OPEN MOTOR DIR AC ON ACT LIMIT SW2 J1 White 8 24VAC 7 Neutral 6 Motor 5 Motor 4 Green Primary DC Motor 3 Black Red 12 V 3 Amp/Hr Red/White Operator Chassis Ground 2 16 17 18 19 20 4405-010 1 1 2 3 4 5 6 7 8 9 10 Orange Black/White HIGH VOLTAGE! 13 14 15 20 ON BATT STAT 10 11 12 NC NO 12 V 3 Amp/Hr 3 4 5 6 7 8 Motor Motor Neutral 24VAC Limit Spare Limit COM 4 5 6 7 8 Blue 1473-010 AUTO OPEN MOTOR DIR AC ON ACT LIMIT SW2 TIMER 115VAC Input P1 3 1 2 3 4 Red Secondary DC ON/OFF Power Switch Secondary Batteries 12 V 3 Amp/Hr Red J1 2 115 VAC INPUT White 1 ON STAT CHARGE CLEAR STAT TRICKLE BATT STAT ON Secondary DC Motor Black – + Secondary Operator Terminal 2 – + RUN TIME HEART BEAT RESET DO NOT use Run Timer Sold Separately 1 – + Red Secondary 1473 Control Board DoorKing Interconnection Cable 1 2 3 4 TIMER 8 ON CLEAR STAT 7 TIME DELAY RUN TIME 6 7 8 9 6 STAT 5 POWER DO NOT use Run Timer P1 1 2 3 4 ON SW2 4 4 CHARGE 3 TRICKLE 2 RESET 1 HEART BEAT 2 3 4 5 2 LMT 115 VAC INPUT EXIT LOOP 1 SW1 1 2 3 4 5 6 7 8 P8 ON P2 Green 1473-065-F-3-18 Gray Orange Brown Yellow Purple Red White Red/White Black/White – + Operator Chassis Ground Blue 1 2 3 4 5 6 7 8 9 10 12 V 3 Amp/Hr 7 9150 Single Slide Gate Operator 0 915 3 4 5 115 VAC Hot Gate Operator Power Terminal DANGER Neu HIGH VOLTAGE! White Blue Single Operator Control Board 1 24 Volt Relay Com 1 2 3 4 5 6 7 8 9 10 J1 115 VAC INPUT P1 TIMER CLEAR STAT Emergency Vehicle Access Dry Contact BATT STAT TRICKLE CHARGE STAT ON 1 2 3 4 ON AUTO OPEN MOTOR DIR AC ON ACT LIMIT SW2 Com N.O. RESET 1473-010 This radio receiver will work during normal daily operation as well as during a power outage. The radio receiver will be powered from the operator’s batteries during a power outage. Dry Contact 4602-010 10 11 12 13 14 15 16 17 18 1 2 3 4 5 SW1 ON Operator DC Motor Connect a normally open device to terminals 1-2. This allows another method to open the gate when a power outage occurs if the auto-open mode is NOT used (1473 DIP-Switch 1 is OFF). KEY SWITCH ON HEART BEAT RUN TIME Black Red Push Button Manual Mode EXIT LOOP 6 7 8 9 Stand-Alone 3-Wire Radio Receiver Manual Mode White Adjust Run Timer Green 2 3 4 5 SW2 NC NO SW1 SW2 Operator DC ON/OFF Power Switch Red/White • Operator will function in either manual or auto open mode (1473 DIP-Switch 1). • 1473 DIP-Switch 4 MUST be OFF and run timer MUST be adjusted. 12 V 3 Amp/Hr – + Red Operator Batteries 12 V 3 Amp/Hr – + Black/White 8 1473-065-F-3-18 9150 Bi-Parting Slide Gate Operators Operator Chassis Ground 0 DANGER 3 4 5 • 1473 DIP-Switch 4 MUST be OFF and run timer MUST be adjusted. 115 VAC Primary Power Terminal Hot White 915 • Operator will function in either manual or auto open mode (1473 DIP-Switch 1). HIGH VOLTAGE! Blue Primary Operator Control Board Green Gray to #2 - not required if the auto open feature is turned ON. 1 1 2 3 4 5 6 7 8 9 10 J1 115 VAC INPUT P1 Stand-Alone 3-Wire Radio Receiver Manual Mode BATT STAT TRICKLE CHARGE STAT ON 1 2 3 4 ON AUTO OPEN MOTOR DIR AC ON ACT LIMIT SW2 RESET 1473-010 Yellow Purple Brown HEART BEAT RUN TIME Primary 1473 Control Board Black Primary DC Motor Red/White HIGH VOLTAGE! Secondary Power Terminal Primary DC ON/OFF Power Switch Primary 12 V Batteries 3 Amp/Hr 3 Hot 4 5 Neu White Blue Optional Gray to #2 See above White Orange – + Black/White 1 2 3 4 5 6 7 8 9 10 J1 Yellow Purple 115 VAC INPUT – + P1 Brown CLEAR STAT TIMER BATT STAT RESET Gray #1 White #2 Blue #3 Red #4 HEART BEAT 1 2 3 4 ON RUN TIME Secondary 1473 Control Board Black Red Black/White 16 17 18 1 2 3 4 5 SW1 Entrapment Protection Terminal SW2 SW1 NC NO Secondary DC Motor White Orange 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 EXIT LOOP KEY SWITCH 4602-010 1 2 3 4 5 SW1 Entrapment Protection Terminal ON – + – + 1473-065-F-3-18 Adjust Run Timer Red/White Red 12 V 3 Amp/Hr TRICKLE 1473-010 12 V 3 Amp/Hr CHARGE STAT ON AUTO OPEN MOTOR DIR AC ON ACT LIMIT SW2 Secondary Batteries 4602-010 10 11 12 1 Green Secondary DC ON/OFF Power Switch KEY SWITCH Secondary Operator Control Board White 12 V 3 Amp/Hr EXIT LOOP DoorKing 7-Wire Interconnection Cable Sold Separately Green Red 6 7 8 9 13 14 15 DANGER 115 VAC Operator Chassis Ground Gray #1 White #2 Blue #3 Red #4 2 3 4 5 ON This radio receiver will work during normal daily operation as well as during a power Com outage. The radio receiver will be N.O. powered from the Push Button operator’s batteries Manual Mode during a power outage. Dry Contact Connect a normally open device to terminals 1-2 of the PRIMARY 1473 ONLY. This allows another method to open the gate when a power outage occurs if the auto-open mode is NOT used (1473 DIP-Switch 1 is OFF). Green Dry Contact Entrapment Protection 4-Wire Cable TIMER CLEAR STAT Emergency Vehicle Access Adjust Run Timer Red White 24 Volt Relay Com SW2 NC NO SW1 9 9310 Single Slide Gate Operator 10 93 • Operator will ONLY function in auto open mode (1473 DIP-Switch 1 ON). • 1473 DIP-Switch 4 MUST be ON (Limit). This allows the 1473 to use the 9310’s magnetic limit for the gate OPEN position. Orange Connects to “OPEN” limit Blue or Yellow wire, depending on mounting position (open left/open right) of the operator. Limit Sensor Plug 1 2 3 4 ON Blue Wire Limit Yellow Wire Limit PRT Com Com 1 2 3 4 5 6 7 8 LMT ON EXIT LOOP 1 2 3 4 5 10 11 12 NO DANGER 20 CLEAR STAT RUN TIME BATT STAT TRICKLE CHARGE STAT 1473-010 ON TIMER 1 2 3 4 13 14 15 16 17 18 19 DO NOT use Run Timer ON 4403-010 HIGH VOLTAGE! REVERSE LOOP 1 2 3 4 5 6 7 8 9 10 NC Green REV SENSE CLOSE RESET P1 White TIME DELAY 115 VAC INPUT HEART BEAT 6 7 8 9 POWER REV SENSE OPEN J1 AUTO OPEN MOTOR DIR AC ON ACT LIMIT SW2 1473 Control Board Blue Black Red White Operator DC Motor Single Operator Control Board Red/White Operator DC ON/OFF Power Switch 12 V 3 Amp/Hr – + Red – + Black/White 10 Operator Batteries 12 V 3 Amp/Hr 1473-065-F-3-18 9310 Bi-Parting Slide Gate Operators 10 93 Connects to “OPEN” limit Blue or Yellow wire, depending on mounting position (open left/open right) of the operator. Limit Sensor Plug Orange 6 7 8 9 J1 P1 TRICKLE CHARGE STAT 1473-010 ON Blue White TIMER Red/White DoorKing Interconnection Cable Sold Separately Primary DC ON/OFF Power Switch – + Connects to “OPEN” limit Blue or Yellow wire, depending on mounting position (open left/open right) of the operator. CLEAR STAT Secondary DC Motor RUN TIME Secondary DC ON/OFF Power Switch BATT STAT Secondary Batteries TRICKLE CHARGE STAT 1473-010 1 2 3 4 TIMER AUTO OPEN MOTOR DIR AC ON ACT LIMIT SW2 12 V 3 Amp/Hr Red ON ON DANGER DO NOT use Run Timer Black Red HIGH VOLTAGE! RESET P1 1 2 3 4 5 6 7 8 9 10 Black/White 1473-065-F-3-18 115 VAC INPUT HEART BEAT Red/White 13 14 15 16 17 18 19 20 Secondary Operator Control Board J1 10 11 12 NO REVERSE LOOP 4403-010 Secondary 1473 Control Board Yellow NC Gray Blue REV SENSE CLOSE 12 V 3 Amp/Hr Orange White REV SENSE OPEN Primary Batteries Brown White Blue Wire Limit Yellow Wire Limit PRT Com Com TIME DELAY Green – + 1 2 3 4 ON POWER PO 6 7 8 9 White 12 V 3 Amp/Hr Red Black/White 1 2 3 4 5 6 7 8 ON LMT 1 2 3 4 5 6 Primary DC Motor Red • 1473 DIP-Switch 4 MUST be ON (Limit). This allows the 1473 to use the 9310’s magnetic limit for the gate OPEN position. 2 3 4 5 AUTO OPEN MOTOR DIR AC ON ACT LIMIT SW2 Black • Operator will ONLY function in auto open mode (1473 DIP-Switch 1 ON). EXIT LOOP RUN TIME BATT STAT 1 2 3 4 DANGER CLEAR STAT Primary Operator Control Board 1 DO NOT use Run Timer ON HIGH VOLTAGE! 13 14 15 16 17 18 19 20 Limit Sensor Plug RESET 1 2 3 4 5 6 7 8 9 10 REVERSE LOOP 115 VAC INPUT HEART BEAT 10 11 12 NO 4403-010 1473 Control Board Green NC Brown Gray White REV SENSE CLOSE Jumper Yellow Blue Wire Limit Yellow Wire Limit PRT Com Com 1 2 3 4 5 6 TIME DELAY REV SENSE OPEN 2 3 4 5 – + 1 2 3 4 ON 1 – + 1 2 3 4 5 6 7 8 LMT ON EXIT LOOP 12 V 3 Amp/Hr 11 1601, 1602, 1603 Single Barrier Gate Operator 160 0 Operator Control Board TIME DELAY UP LOOP Blue 1 2 3 4 5 6 7 8 9 10 J1 115 VAC INPUT P1 Factory Installed DC Magnetic Up Limit Sensor 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 ON Com Yellow N.O. Orange CLEAR STAT TIMER BATT STAT TRICKLE 1 2 3 4 ON AUTO OPEN MOTOR DIR AC ON ACT LIMIT SW2 CHARGE STAT ON 1601-010 POWER RESET 1473-010 DO NOT use Run Timer REVERSE SENSITIVITY RUN TIME HEART BEAT DOWN LOOP 1473 Control Board Black Red NC NO Operator DC Motor DANGER HIGH VOLTAGE! 1 2 3 4 5 6 7 8 9 10 11 12 13 14 White Operator DC ON/OFF Power Switch Red/White – + – + 12 Green White 12 V 3 Amp/Hr Red Black/White Blue Purple 12 V 3 Amp/Hr • Operator will ONLY function in auto open mode (1473 DIP-Switch 1 ON). • 1473 DIP-Switch 4 MUST be ON (Limit). This allows the 1473 to use the 1600’s magnetic limit for the arm UP position. Operator Batteries 1473-065-F-3-18 1601, 1602, 1603 Bi-Parting Barrier Gate Operators Primary Control Board TIME DELAY 160 0 UP LOOP Green Operator Chassis Ground 1 2 3 4 5 6 7 8 9 10 BATT STAT HEART BEAT 1 2 3 4 ON RUN TIME Green White Purple Red/White Yellow Brown Orange Gray Operator Chassis Ground Green Factory Installed DC Magnetic Up Limit Sensor – + Red HIGH VOLTAGE! 1 2 3 4 5 6 7 8 9 10 11 12 13 14 • 1473 DIP-Switch 4 MUST be ON (Limit). This allows the 1473 to use the 1600’s magnetic limit for the arm UP position. Primary DC ON/OFF Power Switch 12 V 3 Amp/Hr NC NO DANGER 1 2 3 4 5 6 7 8 9 10 POWER 1 2 3 4 5 6 7 8 115 VAC INPUT 1601-010 ON J1 P1 – + TIMER REVERSE SENSITIVITY DOWN LOOP BATT STAT TRICKLE RESET DO NOT use Run Timer NC NO White 1 2 3 4 ON 1473-010 DANGER HIGH VOLTAGE! 1 2 3 4 5 6 7 8 9 10 11 12 13 14 HEART BEAT RUN TIME – + 12 V 3 Amp/Hr CHARGE STAT ON AUTO OPEN MOTOR DIR AC ON ACT LIMIT SW2 Red/White Blue White CLEAR STAT Secondary DC ON/OFF Power Switch Secondary 1473 Control Board Red Black – + 1473-065-F-3-18 UP LOOP 1 2 3 4 5 6 7 8 Primary Batteries TIME DELAY ON Black/White 12 V 3 Amp/Hr Secondary Control Board Interconnection Cable Sold Separately RESET 1473-010 Primary DC Motor • Operator will ONLY function in auto open mode (1473 DIP-Switch 1 ON). DoorKing TRICKLE CHARGE STAT ON AUTO OPEN MOTOR DIR AC ON ACT LIMIT SW2 N.O. Orange Black 12 V 3 Amp/Hr 1 2 3 4 5 6 7 8 REVERSE SENSITIVITY DOWN LOOP Primary 1473 Control Board Secondary Batteries ON TIMER CLEAR STAT Com Yellow DO NOT use Run Timer Red POWER 1 2 3 4 5 6 7 8 115 VAC INPUT P1 1601-010 Factory Installed DC Magnetic Up Limit Sensor ON J1 Blue White Red Black/White Green Secondary DC Motor White Purple Yellow Brown Orange Gray 13 Replacement Parts for Convenience Open System Part Number Quantity 1473-010 1801-009 1601-041 2600-196 1601-253 2600-817 2600-688 7082-010 1 2 1 1 1 1 1 1 Description Control Board Battery, 12 Volt, 3.0 Amp Hour Toggle Switch DC Motor Assembly Magnetic Sensor Switch, Barrier Operators Only Magnet, Barrier Operators Only V-Belt 115 VAC Cable Harness Magnetic Sensor Switch P/N 1601-253 Barrier Operators Only Battery 12 Volt 3 Amp/Hr P/N 1801-009 Two (2) required. Magnet P/N 2600-817 Barrier Operators Only J1 115 VAC INPUT RESET HEART BEAT Toggle Switch P/N 1601-041 P1 1 2 3 4 5 6 7 8 9 10 115 VAC Cable Harness P/N 7082-010 RUN TIME CLEAR STAT BATT STAT TRICKLE CHARGE STAT 1473-010 ON 1 2 3 4 ON TIMER AUTO OPEN MOTOR DIR AC ON ACT LIMIT SW2 1473 Control Board P/N 1473-010 V-Belt P/N 2600-688 14 DC Motor P/N 2600-196 1473 Control Board Kit P/N 1473-121 Control board, wire harness and installation manual 1473-065-F-3-18 1473-065-F-3-18 15 Installation Replacement Convenience Open Board Manual For Pre-2016 Convenience Open Operators ONLY Use this manual for circuit board 1473-010. 1473-065-F-3-18 For Pre-2016 Convenience Open Models: 1600, 1602, 1603, 6100, 6300, 6500, 9150 and 9310 Operators ONLY Replacement Board for 2340-010 Convenience Open Board www.doorking.com DoorKing, Inc. 120 S. Glasgow Avenue Inglewood, California 90301 U.S.A. Phone: 310-645-0023 Fax: 310-641-1586
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print, Modify, Annotate, Fill forms, Extract, Print high-res Create Date : 2018:03:16 08:03:10-07:00 Modify Date : 2018:03:16 09:06:24-07:00 XMP Toolkit : Adobe XMP Core 5.4-c006 80.159825, 2016/09/16-03:31:08 Metadata Date : 2018:03:16 09:06:24-07:00 Producer : Acrobat Distiller 10.1.16 (Macintosh) Format : application/pdf Title : untitled Document ID : uuid:539c98d0-2475-e544-8754-dfe6c715ba8c Instance ID : uuid:cbb15bbf-6dc4-4176-8094-ef91cc64c949 Page Count : 18EXIF Metadata provided by EXIF.tools