DoorKing Door King 1601 Lighted Aluminum Arm Installation Kit 536 D 2 18 Pwr Harness

User Manual: DoorKing DoorKing 1601 Lighted Aluminum Arm Installation Kit Installation Manual

Open the PDF directly: View PDF .
Page Count: 2

Download
Open PDF In Browser	View PDF

DoorKing Part Number

LIGHTED ALUMINUM ARM INSTALLATION KIT

1601-535

This kit is designed for use on a 1601 or 1603 barrier gate operators. Not for use on a 1602 operator. This kit provides a wire
harness to install an aluminum arm WITH LED lights, aluminum arm with LEDs sold separately (P/N 1601-518).

Kit Includes: Wire Harness, Power Transformer, Zip Ties, Adhesive Zip Ties.

Wire Run Options in Operator Cabinet

Shorten Arm Length if Desired

Far

S
Op ide
tion

Kn

ock

Re

Ou

flec
Tap tive
e

t

ed
cur
Se inet
n
Ru ab
re f C
Wi op o
T
to

Inc
l
Ad uded
h
Zip esive
Tie
s

ONLY cut LED tape on
Indicated cut marks.

Kn

ock

Ne
ar
Op Side
tion

LED Tape

Ou

t

Peel back reflective tape on both sides
of arm. Cut the LED tape with scissors
ONLY where indicated on the tape or
LED wiring inside the tape WILL GET
DAMAGED AND NOT LIGHT!

Exi
s
Wi ting
re
Re
str
ain
er

stic
Pla Cap
d
En
LED Tape

Cut arm where desired with a fine tooth saw. Be careful not to damage the
LED tape with the saw. Re stick reflective tape back over LEDs. Reinstall
plastic end cap over end of arm.

Installation

Op

Mount Wire Guard
in Knock-Out hole
on operator cabinet.

Hub MUST already be installed on
gate operator. See Installation/
Owner’s manual for correct hub
installation.

era

tor

Cab
Use existing wire
ine
t
restrainers to secure wire
harness in operator cabinet.
Make sure wire is clear of moving
parts.

Allow enough
slack in the wire
for rotating arm.

Secure arm bracket to hub
with hub/arm bracket
hardware (4 nuts, bolts,
lockwashers and washers)
as shown.

Hu
b

Note for Older 1601/1603 Operators: A 5/8” hole
will have to be drilled in the operator cabinet
approximately where Knock-Out is shown. Make
sure 5/8” hole is clear of all internal components.

A
Secrm
ur
Bo ing
lts

Arm

re
Wi ss
e
n
r
Ha

Bra
c

Secure Wire Harness

ket

Blu

Use included zip ties to secure ALL wires to
arm bracket/Hub after making connections.
Make sure that all wires remain clear of the
rotating arm and the plastic cover.

e

Blu

e Red

Re
d

LED

Alu

min

Lig

hts

um

Arm

wit

hL

ED

s(

So

ld S
epa

rat

Pla

stic

Co

ver

1601-536-D-2-18
1

ely

)

DoorKing Part Number

Power Arm LEDs from Operator

01

Connect power transformer to 115 VAC power.
Use existing wire restrainers and included zip ties to secure wire.
Make sure all wires are clear of moving parts.

Wire
Harness

1601-535

16

Plug power transformer into wire harness.

/16

03

re

i
gW
stin ner
i
x
E trai
s
Re

AC e
5 V nc
11 venie
n
Co et
tl
Ou

BlackRed+

Tra
n

sfo

rm

r er
we
Po sform
n
Tra
er

Plu

g

Wire Schematic for LEDs to Operator
Wire Guard

115 VAC
Convenience Outlet

Wire Harness
Blue-

Power
Transformer

Red+

Allow enough
slack in wire
for rotating arm.

Blue-

LED Lights
Black-

Red+

12 V

Red+

LED Lights are on Arm P/N 1601-518 (Sold Separately)

Plastic Cover

Manual Release when NO “convenience open” or “manual release kit” are used
To manually release an aluminum arm when
NO convenience open or manual release kit
are being used:

Hu

1

2

b

3

W
Gu ire
ard
Wi
r
Ha e
rn

ess

Po
w
Tra er
nsf
orm

er

Un-plug power transformer
from wire harness.
1601-536-D-2-18

Un-bolt arm from the hub
(4 bolts) and remove arm.

Ha Wire
rne
ss

Un-screw wire guard and remove
wire harness from operator.
Copyright 2018 DoorKing, Inc. All rights reserved.
2

120 S. Glasgow Avenue
Inglewood, California 90301 U.S.A.



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Modify, Annotate, Fill forms, Extract, Print high-res
Create Date                     : 2018:02:19 09:31:38-08:00
Modify Date                     : 2018:02:19 10:05:08-08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c006 80.159825, 2016/09/16-03:31:08
Metadata Date                   : 2018:02:19 10:05:08-08:00
Producer                        : Acrobat Distiller 10.1.16 (Macintosh)
Format                          : application/pdf
Title                           : untitled
Document ID                     : uuid:64c87f13-f4b8-f943-a6cd-5aab531afca3
Instance ID                     : uuid:9b4ef12d-0ca2-4bf6-87d4-f74370182511
Page Count                      : 2

EXIF Metadata provided by EXIF.tools