DoorKing 8054 065 D 3 12 Door King Series Installation Manual
User Manual: DoorKing DoorKing 8054 Series Installation Manual Installation Manual
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
DoorKing Part Numbers ® MODEL 8054 MicroPLUS RF RECEIVER The model 8054 is a High Security Encrypted “Rotating Code” RF Receiver that is designed for stand alone applications. The encrypted “Rotating Code” programming in this receiver and the companion MicroPLUS® transmitters prevent copied transmitter codes from being used again to access a controlled entry point. The 8054 receiver includes 10 time zones (eight programmable), a history buffer that can store up to 2800 transactions in its memory. A serial printer can be connected to print the stored transactions or the receiver can be programmed to print transactions in real time mode. 8054-081 50 Transmitter Codes 8054-082 100 Transmitter Codes 8054-083 250 Transmitter Codes 8054-084 500 Transmitter Codes 8054-085 1000 Transmitter Codes 8054-086 1250 Transmitter Codes The MicroPLUS® transmitter codes that the 1B 2B 3B utt utt utt on on on receiver will respond to can also be defined by “Facility Codes”, and “Transmitter Button P/N 8069-080 P/N 8070-080 P/N 8071-080 Codes”. For example: an 8054 receiver can be Use ONLY MicroPLUS® Transmitters programmed to respond to only the first button ® on a multiple button MicroPLUS transmitter while a second 8054 receiver can be programmed to respond to only the second button of the same multiple button MicroPLUS® transmitter. Thus allowing a single multiple button MicroPLUS® transmitter to activate two different receivers without fear of both receivers responding to the same transmitter code. There are three (3) different “2 Button” MicroPLUS® transmitter button combinations that each receiver can be programmed to respond to: button-1, button-2 and buttons 1&2 pressed at the same time. There are six (6) different “3 Button” MicroPLUS® transmitter button combinations that each receiver can be programmed to respond to: button-1, button-2, button-3, buttons 1&2 pressed at the same time, buttons 2&3 pressed at the same time and buttons 1&3 pressed at the same time. * Installation This receiver is NOT designed to be installed outdoors without being protected from the weather. An outdoor enclosure is available for the receiver if required Removable (P/N 8057-110 - Metal Outdoor Box). receiver terminal Install the 8054 receiver in a location so the antenna is NOT surrounded by Re for easy wiring. D LE Terceive metal and is in free air as high as possible above the ground. A longer Coax RF mi r n e al Antenna kit is available for the receiver if required (P/N 1514-073 - Includes od r C on steButtge) antenna, mounting “L” bracket and 15 feet of coax cable). An antenna amplifier a 12 M pa 34 ext kit (P/N 8058-080) or a Yagi directional antenna kit (P/N 1514-072) is also 56 en 78 (Se 18” available for the receiver if required. Coax The RF LED on the side of the case will blink as RF energy is received. Cable #1 - Input Power 12-24 Volt AC, 12-24 Volt DC (Negative) If the LED blinks or is on continuously, this indicates that there may #2 - Input Power 12-24 Volt AC, 12-24 Volt DC (Positive) be interference on the frequency (318 MHz) and short range may be #3 - Relay Contact (Normally Open) Terminals 3-4-5 the result. If this happens, try relocating the receiver or remove the #4 - Relay Contact (Normally Closed) rated for 30 volt, source of interference. An antenna amplifier or a directional antenna 1 amp max. #5 - Relay Contact (Common) may be needed. #6 - Printer Data Note: Loop detectors and proximity card readers can cause receiver (P1 DoorKing Printer Interface Terminal) interference. #7 - Printer Signal Ground (P2 DoorKing Printer Interface Terminal) #8 - Printer Busy (P3 DoorKing Printer Interface Terminal) 0 9 6 8 # 3 5 7 2 4 1 Receiver Terminal Wiring Stand-Alone Power and Device Wiring : 12-24 Volt Transformer Connect 12 - 24 Volt AC or DC power to terminals #1 and #2. Use minimum 18 AWG wire to power the receiver. • If DC power is used (Transformer): Terminal #1 is NEGATIVE and Terminal #2 is POSITIVE. Coax Antenna Kit (Included) • Connect the receiver relay contacts to the device to be activated. - Receiver Terminal #3 is the relay contact Normally OPEN (N.O.) - Receiver Terminal #4 is the relay contact Normally CLOSED (N.C.) - Receiver Terminal #5 is the relay contact Common (C). To Printer Printer: Connect receiver directly to a printer using the printer interface terminal as shown. • Maximum wire run for printer data is 500 ft using Belden 9931, Consolidated 5324-CL or equivalent shielded wire. DO NOT use twisted pair wire for printer data. • Serial printer setting: 9600 baud, 1 start, 8 data, 1 stop. Printer Cable Not Supplied 25-Pin Connector DC Polarity Matters! To Receiver Terminal #1 (Neg.) To Receiver Terminal #2 (Pos.) P1 To Receiver Terminal #6 P2 To Receiver Terminal #7 P3 To Receiver Terminal #8 Printer Interface Terminal P/N 1587-010 120 Glasgow Avenue Inglewood, California 90301 U.S.A. Programming Programming BEEPS: The receiver is equipped with a “beeper” to help guide you through the programming steps. When required data has been entered correctly and the key is pressed, a “BEEP” will be heard. A “BEEEEEEEEEP” indicates programming has ended successfully OR there has been NO data input for 20 seconds. Four (4) long beeps in a row indicates that an error has occured (Examples: Data was entered incorrectly, not enough memory to store all transmitters or receiver is in real time printing mode but printer is not connected or not turned on). Program the Master Code: The master code is the four-digit number required to gain access to the receiver memory for all programming. You MUST program a MASTER CODE first. 0 * 9 6 8 # 3 5 7 1. Press Master Code Button ad yp Ke 2 4 1 RF 12 34 de Co er ton ast But 56 Write Down Your Master Code 1st Digit 2nd Digit 3rd Digit 4th Digit M 78 D LE any four numbers 2. Choose and enter four-digits on the keypad ? ? ? ? then press “BEEP” Important Note: Keep this instruction sheet for future reference after writing down the master code . There is NO way of retrieving the master code after it has been programmed in. If you forget it, you will have to program in a new master code but all other previously programmed information will remain intact. Add a Transmitter: Unique codes located on back of transmitter (Five-digit Transmitter Code - Tr) and (Four-digit Facility Code - Fc). 1. Press 1 0 and the four-digit Master Code. “BEEP” 2. Enter the two-digit transmitter button number that the receiver is to respond to, then press “BEEP” Button 1 - 0 1 Button 2 - 0 2 3. Enter the four-digit facility code, then press “BEEP” Note: Valid facility codes are 0000 - 4095. Button 3 - 0 3 4. Enter the LOWEST five-digit transmitter code, then press “BEEP” Buttons 1&2 together - 1 5. Enter the HIGHEST five-digit transmitter code, then press “BEEP” Note: Valid transmitter codes are 00000 - 65407. If adding a single transmitter, the lowest and highset five-digit number will be the same. Buttons 2&3 together - 2 2 3 Buttons 1&3 together - 1 3 6. Enter the single-digit Time Zone number, then press “BEEP” Note: Valid Time Zones are 0 - 9. There are 10 available time zones. Time zones 2 - 9 are programmable (See “Programming Time Zones” programming on next page). Entering 0 will never allow access to the transmitter(s) being programmed. Entering 1 will always allow access to the transmitter(s) being programmed. When programming a block of transmitter numbers, the receiver will “BEEP” every three seconds. Wait for this beeping to stop before proceeding with any other programming.This may take up to five minitues depending on the memory size and the number of transmitters being programmed. 7. Repeat steps 2 - 7 to enter an additional transmitter or block of transmitters or press 0 to end the programming. A “BEEEEEEEEEP” will be heard when finished. at the same time or simply wait 20 seconds Delete a Transmitter One at a Time: Unique codes located on back of transmitter (Five-digit Transmitter Code - Tr) and (Four-digit Facility Code - Fc). 1. Press 1 2 and the four-digit Master Code. “BEEP” 2. Enter the two-digit transmitter button number to be deleted, then press 3. Enter the four-digit facility code to be deleted, then press 4. Enter the five-digit transmitter code to be deleted, then press “BEEP” “BEEP” “BEEP” 3. Repeat steps 2 - 4 to delete additional transmitters if desired or press 0 to end the programming. A “BEEEEEEEEEP” will be heard when finished. at the same time or simply wait 20 seconds Delete ALL Transmitters at Once: WARNING: Deleted transmitters CANNOT be retrieved. 1. Press 1 3 and the four-digit Master Code. “BEEP” 2. Enter 9999, then press “BEEP” 3. After approximately 1 1/2 minutes of “BEEPS” every three seconds, one long “BEEEEEEEEEP” will be heard when finished. 120 Glasgow Avenue Inglewood, California 90301 U.S.A. Programming Continued Relay Strike Time: The amount of time the receiver relay activates. 1. Press 0 3 and the four-digit Master Code. “BEEP” 2. Enter a two-digit number (01-99) for the relay activation in seconds, then press 3. Press 0 “BEEP” TOGETHER to end programming or wait 20 seconds.“BEEEEEEEEEP” Program Current Time and Day: Current hour and minute, AM or PM, current month, current day and current year. 1. Press 3 3 and the four-digit Master Code. “BEEP” 2. Enter a four-digit current hour and minute (time example - 7:43 - 0743), then press “BEEP” 3. Enter 0 for AM or 1 for PM, then press “BEEP” 4. Enter a two-digit current month (01 - 12), then press “BEEP” 5. Enter a two-digit current day of the month (01 - 31), then press 6. Enter the last two-digits of the current year, then press “BEEP” “BEEP” 7. Enter a single-digit day of the week (1 = Sunday, 2 = Monday, 3 = Tuesday...... 7 = Saturday), then press 8. Press 0 “BEEP” TOGETHER to end programming or wait 20 seconds. “BEEEEEEEEEP” Programming Time Zones: Can be used for Step 6 of “Add a Transmitter” on the previous page. 3 8 and the four-digit Master Code. “BEEP” 2. Enter a single-digit time zone to be programmed (ONLY 2 - 9 time zones are valid), then press “BEEP” 1. Press “BEEP” 3. Enter the Beginning time using four-digits for the hours and minutes (time example - 9:45 - 0945), then press 4. Enter 0 for AM or 1 for PM, then press “BEEP” 5. Enter the Ending time using four-digits for the hours and minutes (time example - 5:00 - 0500), then press 6. Enter 0 for AM or 1 for PM, then press “BEEP” “BEEP” 7. Enter a seven-digit number for the days of the week that the time zone is active, then press “BEEP” Use the key to skip days that are not active (1 = Sunday, 2 = Monday, 3 = Tuesday...... 7 = Saturday). Example 1: If the time zone is active Monday - Friday only, then enter 2 3 4 5 Example 2: If the time zone is active Monday, Wednesday and Friday only, then enter 2 6 4 6 8. Repeat steps 2 - 7 to program additional time zones or press 0 at the same time or simply wait 20 seconds to end the programming. A “BEEEEEEEEEP” will be heard when finished. 120 Glasgow Avenue Inglewood, California 90301 U.S.A. Programming Continued Print Mode: Turn “Real Time Mode” ON or OFF. 1. Press 3 5 and the four-digit Master Code. “BEEP” 2. Enter 1 to print in “Real Time Mode” or enter 0 NOT to print in real time mode, then press “BEEP” In either case, the transactions are stored in the receiver’s buffer and can be printed later (See “Print” below). If programmed for “Real Time Mode”, printer MUST be connected and turned ON, otherwise the receiver will sound four long beeps. 3. Press 0 TOGETHER to end programming or wait 20 seconds.“BEEEEEEEEEP” Print: Print all transactions stored in the receiver’s buffer. 1. Press 3 7 and the four-digit Master Code. “BEEP” The transactions stored in the receivers buffer will print. The receiver will sound one long “BEEEEEEEEEP” when finished. Print Transactions for a Specific Day ONLY: Used to print only a desired day’s transactions and not the entire buffer. 1. Press 3 4 and the four-digit Master Code. “BEEP” 2. Enter the two-digit specific month desired (01 - 12), then press “BEEP” 3. Enter the two-digit specific day of the month desired (01 - 31), then press “BEEP” Only the desired day’s transactions stored in the receiver’s buffer will print. The receiver will sound one long “BEEEEEEEEEP” when finished. Clear Transaction Buffer: WARNING: Deleted transactions CANNOT be retrieved. Up to 2800 transactions are stored in buffer. 1. Press 3 6 and the four-digit Master Code. “BEEP” 2. Enter 9999, then press “BEEP” This sequence will take about 5 minutes of “BEEPS” every three seconds, one long “BEEEEEEEEEP” will be heard when finished. This device complies with the FCC Rules Part 15. Operation is subject to the following two conditions: 1.) This device may not cause harmful interference. 2.) This device must accept and interference received, including interference that may cause undesired operation. This class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouilleur du Canada. 8054-065-D-3-12 Copyright 2012 DoorKing, Inc. All rights reserved. 120 Glasgow Avenue Inglewood, California 90301 U.S.A.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print, Modify, Annotate, Fill forms, Extract, Print high-res Author : mitch freed Create Date : 2012:03:14 09:38:55-07:00 Modify Date : 2013:08:22 14:51:54-07:00 XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Creator Tool : Adobe Illustrator CS4 Metadata Date : 2013:08:22 14:51:54-07:00 Thumbnail Width : 192 Thumbnail Height : 256 Thumbnail Format : JPEG Thumbnail Image : (Binary data 15015 bytes, use -b option to extract) Format : application/pdf Creator : mitch freed Title : 8054-065-D-3-12.indd Document ID : xmp.did:74117FD920071168B5D4F45612C98A0C Instance ID : uuid:ef9f387c-0a5b-e748-8893-d24d45a01581 Original Document ID : xmp.did:74117FC6200711689D0BDBD6DB57A403 History Action : converted, converted, converted, saved, converted, converted, converted, converted, converted, converted, converted, converted, converted, converted, converted, converted, converted, converted, converted, converted, converted, converted, saved, converted, converted, converted, converted, converted, converted, converted, converted, converted, converted, converted, converted, converted, converted, saved, converted, converted, converted, converted, converted, converted History Parameters : from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator History Instance ID : xmp.iid:74117FC6200711689D0BDBD6DB57A403, xmp.iid:74117FCF20071168B0DFC7EC263EF110, xmp.iid:74117FD920071168B5D4F45612C98A0C History When : 2011:08:05 14:34:11-07:00, 2011:08:10 06:18:06-07:00, 2011:08:19 05:03:25-07:00 History Software Agent : Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4 History Changed : /, /, / Derived From Instance ID : xmp.iid:74117FCF20071168B0DFC7EC263EF110 Derived From Document ID : xmp.did:74117FCF20071168B0DFC7EC263EF110 Derived From Original Document ID: xmp.did:74117FC6200711689D0BDBD6DB57A403 N Pages : 1 Has Visible Transparency : False Has Visible Overprint : False Max Page Size W : 8.500000 Max Page Size H : 11.000000 Max Page Size Unit : Inches Font Name : Helvetica-Condensed-Bold, Helvetica-Condensed, Impact Font Family : Helvetica, Helvetica, Impact Font Face : Bold Condensed, Medium Condensed, Regular Font Type : Type 1, Type 1, TrueType Font Version : 003.001, 003.001, Version 2.35 Font Composite : False, False, False Font File Name : HelveConBol; Helvetica Condensed, HelveCon; Helvetica Condensed, Impact Plate Names : Cyan, Magenta, Yellow, Black Swatch Group Name : Default Swatch Group Swatch Group Type : 0 Swatch Colorant Swatch Name : White, Black, Magenta, Red, Crimson, Orange, Peach, Custard, Yellow, Lime, Dried Sage, Green, Forest, Mediterranean, Bright Blue, Pure Cyan, Night Blue, Slate, Periwinkle, Plum, Lavender, Baby Pink, Bisque, Cafe Con Leche, Malt, Mocha, Pigeon, Battleship, Global Black, Global Red, Global Orange, Global Yellow, Global Lime, Global Green, Global Blue, Global Night, Global Periwinkle, Global Plum, Global Pink, Global Malt, New Color Swatch 3, New Color Swatch 1, New Color Swatch 2, New Color Swatch 4, PANTONE 185 C, New Color Swatch 5, New Color Swatch 6, New Color Swatch 7, New Color Swatch 8, R=95 G=138 B=100, R=162 G=197 B=154, R=139 G=175 B=133, K=20, K=71, K=60 Swatch Colorant Mode : CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK Swatch Colorant Type : PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, SPOT, PROCESS, SPOT, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS Swatch Colorant Cyan : 0.000000, 0.000000, 0.000000, 0.000000, 26.999998, 0.000000, 2.999997, 0.000000, 0.000000, 33.000000, 36.000000, 80.000000, 90.000000, 100.000000, 45.999996, 100.000000, 100.000000, 30.000002, 42.999996, 50.000000, 18.000000, 0.000000, 6.999999, 25.000000, 33.000000, 42.999996, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 33.000000, 80.000000, 45.999996, 100.000000, 42.999996, 50.000000, 0.000000, 32.549999, 92.549995, 0.000000, 8.630000, 11.000002, 0.000000, 49.360001, 56.029999, 62.349998, 56.079994, 65.896103, 38.638897, 49.298798, 16.891701, 58.886101, 52.086700 Swatch Colorant Magenta : 0.000000, 0.000000, 100.000000, 100.000000, 94.000000, 50.000000, 26.000000, 13.000000, 0.000000, 0.000000, 10.000002, 0.000000, 30.000002, 0.000000, 0.000000, 0.000000, 50.000000, 0.000000, 27.999996, 90.000000, 45.999996, 25.000000, 24.000000, 41.999996, 44.000000, 52.000000, 0.000000, 0.000000, 0.000000, 100.000000, 50.000000, 0.000000, 0.000000, 0.000000, 0.000000, 50.000000, 28.000000, 90.000000, 25.000000, 44.309998, 0.000000, 6.500000, 10.200001, 13.000000, 91.000000, 38.489998, 43.690002, 48.629997, 3.140002, 28.439798, 8.084200, 16.931400, 12.332300, 49.778000, 42.627602 Swatch Colorant Yellow : 0.000000, 0.000000, 0.000000, 100.000000, 94.000000, 100.000000, 81.000000, 63.000000, 100.000000, 72.999992, 47.000004, 100.000000, 90.000000, 30.000002, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 37.000000, 48.000000, 53.999996, 80.000000, 0.000000, 0.000000, 0.000000, 100.000000, 100.000000, 100.000000, 72.999992, 100.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 53.730000, 100.000000, 13.000000, 61.959999, 26.000000, 76.000000, 38.489998, 43.690002, 48.629997, 89.800003, 70.519600, 47.620399, 57.643997, 12.082100, 47.208397, 41.037601 Swatch Colorant Black : 0.000000, 100.000000, 0.000000, 0.000000, 26.000000, 0.000000, 4.000002, 0.000000, 0.000000, 0.000000, 1.999998, 0.000000, 17.000002, 5.000001, 0.000000, 0.000000, 0.000000, 42.999996, 0.000000, 0.000000, 0.000000, 0.000000, 1.999998, 11.000002, 19.000000, 38.000000, 30.000002, 70.000000, 100.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 19.610001, 0.000000, 0.000000, 0.390000, 1.999998, 0.000000, 38.000000, 41.999996, 47.840000, 0.389999, 9.033300, 0.000000, 0.598200, 0.000000, 15.829700, 6.289800 Swatch Colorant Tint : 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000 Producer : Acrobat Distiller 9.5.0 (Macintosh) Page Count : 4EXIF Metadata provided by EXIF.tools