Dream Technology DT100 Bluetooth Headset User Manual
Dream Technology Co., Ltd. Bluetooth Headset
User Manual
DT100
User Manual
Package Contents
Features
Charging
Power On / Off
Pairing / Reconnection
This headset has its own battery inside. The internal battery
Must be fully charged before first time use.
72 hours3 hours2 hours
Standby TimeTalk TimeCharging Time
-. Charging in progress : Red light on
-. Charging completed : Blue light on
Press and hold down Power/Call Button
Until Red light flashes 3 times.
(Approx. 3 seconds)
Off
Press and hold down Power/Call Button
until Blue light flashes 4 times.
(Approx. 3 seconds)
On
instructionFunction
Pairing
Pair the headset with the mobile phone before using the device.
Pairing is a process which establishes a new relationship
between two Bluetooth enabled devices through the
exchange of a link key.
ⒶMake sure that the headset is turned off.
ⒷSet the headset to a pairable state.
Press and hold down for 5 seconds until blue light is
turned on.
ⒸSearch for the headset on your mobile phone according
to the guide of the phone. In most cases, selecting ¡set¡
and ¡connection¡ from the menu to search for the bluetooth
device. You may also select the option to add the device
directly.
ⒹWhen the mobile phone finds DT100, pair it with the phone.
ⒺIn case the mobile phone asks for passkey or PIN, enter
0000 to connect the two devices.
Reconnection
Reconnection is needed when you are out of range and then
Come back into range or when the headset is powered on again.
Tap the Power/Call Button once.
Specifications
Functions
Make a Call
-. Last number Redialing
Tapping the Power/Call Button once displays the list and
Tap the Power/Call Button to make a call
Notes) For some mobile phones, calls can be directly made displaying the list.
-. Voice Dial
Tapping the Power/Call Button once and say the person¡s
name.
Notes) Voice dial can be used only if the mobile phone has voice recognition
feature and the headset is registered under handsfree service.
Please see the user guide of your phone for detail.
End a Call
-. Tap the Power/Call Button once.
Accept a Call
-. Tap the Power/Call Button once after the tone (incoming)
Reject a Call
-. Press and hold down the Power/Call Button for 1 second.
Notes) The reject call function can be used only if the mobile photo has a reject
call feature. The headset must be registered under a handsfree service
Adjust volume
-. Tap the volume Button (▲or ▼) to adjust volume
accordingly.
Microphone Mute
-. Press the volume Button (▲or ▼) for 1 second during
a call.
Cancellation is same.
Call Transfer
-. Tap the Power/Call Button once.
Notes) you can switch to the headset only once when you receive a call from the
mobile phone.
Call waiting
-. Press the Power/Call Button for 1 second when another
call arrives during a call.
Notes) The function can be used only if the service provides the call waiting
function. The headset must be registered under the handsfree service.
Please see the user guide for detail.
10gWeight
65.7(L) X 18 (W) X 16 (H)Dimensions (mm)
Up to 72 hoursStandby Time
Up to 3 hoursTalk Time
Up to 10m (33 feet)Operating Range
Version 2.0 (Class 2)Bluetooth Version
<<NOTICE>>
* Section 15.19 Labelling requirements
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference and
(2) This device must accept any interference received,
(3) including interference that may cause
undesired operation.
* Section 15.21 Information to user
The changes or modifications not expressly approved by
the party responsible for compliance
could void the user’s authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure
compliance requirements, no change to the antenna or the
device is permitted. Any change to the antenna or the device
could result in the device exceeding the RF exposure requirements
and void user’s authority to operate the device.