Drill Masters Eldorado Tool Welder 93420 Users Manual 93421 Bi Metal Hole Saws

2015-02-04

: Drill-Masters-Eldorado-Tool Drill-Masters-Eldorado-Tool-Drill-Masters-Eldorado-Tool-Welder-93420-Users-Manual-514785 drill-masters-eldorado-tool-drill-masters-eldorado-tool-welder-93420-users-manual-514785 drill-masters-eldorado-tool pdf

Open the PDF directly: View PDF PDF.
Page Count: 6

DownloadDrill-Masters-Eldorado-Tool Drill-Masters-Eldorado-Tool-Drill-Masters-Eldorado-Tool-Welder-93420-Users-Manual- 93420 93421 Bi Metal Hole Saws  Drill-masters-eldorado-tool-drill-masters-eldorado-tool-welder-93420-users-manual
Open PDF In BrowserView PDF
BI-METAL HOLE SAWS
FOR ELECTRICIANS (MODEL 93420)
FOR PLUMBERS (MODEL 93421)
9 PCS. IN EACH SET

93420
93421
ASSEMBLY & OPERATING INSTRUCTIONS

Due to continuing improvements, actual product may differ slightly from the product described therein.

®

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web Site at www.harborfreight.com
Copyright© 2005 by Harbor Freight Tools®. All rights reserved. No portion of this manual or
any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
For technical questions and replacement parts please call 1-800-444-3353.

THANK YOU for choosing a HARBOR FREIGHT TOOLS product. For future reference, please

complete the owner’s record below:
Model______________

Serial No.___________

Purchase Date_______________

SAVE THE RECEIPT, WARRANTY AND THESE INSTRUCTIONS. It is important that you read
the entire manual to become familiar with the unit BEFORE you begin assembly.
Technical Specifications
The M3 High speed steel cutting edge is electronic beam welded to an alloy steel body for tougher
and longer lasting teeth. Alternate tooth set for smoother and faster cuts with better chip clearance.
The bi-metal construction provides durability and long life. Heat vents for cooler running.
135 degree split point Pilot bit for better penetration and to prevent skating.
Each kit contains 6 Hole Saws, 2 Pilot Bits, 2 Mandrels and a Mandrel Adapter. For Hole Saw sizes
see the listing on page 4.
Maximum RPM:

Maximum drill speeds for various types of material - see chart on page 6.

Safety Warnings and Precautions
WARNING: When using product, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment.
Read all instructions before using this product!
1.

Keep work area clean. Cluttered areas invite injuries.

2.

Observe work area conditions. Keep work area well lighted.

3.

Store idle equipment. When not in use, the Hole Saws must be stored in a safe and clean
location. Always lock up products and keep out of reach of children.

4.

Use the right product for the job. There are certain applications for which the Hole Saws
were designed. Do not modify the Hole Saws and do not use the Hole Saws for a purpose for
which they were not intended.

5.

Check for damaged parts. Before using any product, any part that appears damaged should
be carefully checked to determine that it will operate properly and perform its intended function.
Check for any broken or damaged parts and any other conditions that may affect its operation.
Replace or repair damaged or worn parts immediately.

6.

Replacement parts and accessories. When servicing, use only identical replacement parts.
Use of any other parts will void the warranty.

7.

Do not operate product if under the influence of alcohol or drugs. Read warning labels on
prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there
is any doubt, do not operate the product.

SKU 93420/93421

For technical questions please call 1-800-444-3353.

Page 2

8.

Use eye and ear protection. Always wear ANSI approved impact safety goggles. Wear a full
face shield if you are producing metal filings and wood chips. Wear an ANSI approved dust
mask or respirator when working around metal, wood, and chemical dusts and mists.

9.

Do not overreach. Keep proper footing and balance at all times. Do not reach over or across
running machines.

10. Maintain tools with care. Keep tools sharp and clean for better and safer performance. Follow
instructions for lubricating and changing accessories. Inspect tool cords periodically and, if
damaged, have them repaired by an authorized technician. Inspect all components of the BiMetal Hole Saw for damage. Never use a damaged or cracked drill bit, hole saw blade or
mandrel.
11. Always check hardware and assembled parts after assembling. All connections should be
tight and hardware tightened.
12. Do not force this product. Do not use inappropriate attachments in an attempt to exceed the
Hole Saw’s capacity.
13. Keep children away. Children must never be allowed in the work area.
14. Read the instruction manual provided by your drill’s manufacturer and adhere to all
warnings and instructions.
15. Before each use check to see that the drill bit is tightly mounted to the Mandrel. The
Mandrel’s screw tip should be in contact with the step flat portion of the bit before tightening the
screw.
Warning:

The warnings, cautions, and instructions discussed in this instruction manual cannot
cover all possible conditions and situations that may occur. It must be understood by
the operator that common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities, contain chemicals known [to the State of California] to cause
cancer, birth defects or other reproductive harm. Examples are: A) Lead from leadbased paints, B) Crystalline silica from bricks and cement or other masonry
products, C) Arsenic and chromium from chemically treated lumber. (California
Health & Safety Code § 25249.5, et seq. )
Unpacking

When unpacking your Bi-Metal Hole Saws, make certain that all parts on page 5 of this manual are
included. If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at
1-800-444-3353.
Assembly and Operation
Your 9 PC Bi-Metal Hole Saw will require some easy assembly. It is important that you read the
entire manual to become familiar with the product BEFORE you assemble and use the Hole Saws.
Wearing work gloves are recommended when assembling this product.
Electrician’s Hole Saw (93420)
Hole Saw sizes 2-1/2”, 2”, 1-3/4” and 1-3/8” can be used with either the 1/4” Mandrel or the 7/16”
Mandrel. The Mandrel you choose to use will depend on the size of the Pilot Bit desired.
Decide on the Hole Saw size to be used-refer to the Parts List on page 5.
SKU 93420/93421

For technical questions please call 1-800-444-3353.

Page 3

Using the 7/16” Mandrel with 2-1/2”, 2”, 1-3/4”, 1-3/8”
1. Thread the Hole Saw onto the end of the Mandrel.
2. Slide the Pin Connecting Ring up so that the Guiding Pins fit into two of the holes on the base of
the Hole Saw-see Figure 1 A.
93420-Using the 7/16” Mandrel (Cont’d)
3. Thread the nut up (toward the bit) to tighten the Pin Connecting Ring against the Hole Saw.
93420-Using the 1/4” Mandrel with 2-1/2”, 2”, 1-3/4”, 1-3/8”
1.

Thread the Mandrel Adapter (11) down onto the Mandrel.

2.

Slide on the Mandrel Ring (13). Thread on the Hole Saw-see Figure 1 B.
93420-Using the 1/4” Mandrel with 1-1/8” and 7/8”
The 1-1/8” Hole Saw and the 7/8” Hole Saw can only be used with the 1/4” Mandrel.

1.

Thread the Hole Saw down onto the Mandrel.
Mounting to the Drill

1.

After attaching the Hole Saw to the desired Mandrel, the Hole Saw is now ready to be
mounted to the drill. Read the drill owner’s manual for instructions on properly mounting drill
bits.

2.

Before using the Hole Saw, make certain that the work piece is firmly clamped in place.
Mark the center of the hole to be drilled using a centerpunch. Place the drill bit in the
centerpunch impression, and slowly begin drilling into the workpiece. Always hold the drill
firmly with both hands to ensure safe operation of the Hole Saw.
Figure 1
B

A
Pin

Hole Saw

Mandrel Ring (13)

1/4” Mandrel

Adapter (11)

Plumbers Hole Saw (93421)
Hole Saw sizes 2-1/4”, 1-3/4” and 1-1/2” can be used with either the 1/4” Mandrel or the 7/16”
Mandrel. The Mandrel you choose to use will depend on the size of the Pilot Bit desired.
Decide on the Hole Saw size to be used-refer to the Parts List on page 5.
93421-Using the 7/16” Mandrel with 2-1/4”,1-3/4”, 1-1/2”
1. Thread the Hole Saw onto the end of the Mandrel.
2. Slide the Pin Connecting Ring up so that the Guiding Pins fit into two of the holes on the base of
the Hole Saw-see Figure 1 A.
3. Thread the nut up (toward the bit) to tighten the Pin Connecting Ring against the Hole Saw.
SKU 93420/93421

For technical questions please call 1-800-444-3353.

Page 4

93421-Using the 1/4” Mandrel with 2-1/4”,1-3/4”, 1-1/2”
1.

Thread the Mandrel Adapter (11) down onto the Mandrel.

2.

Slide on the Mandrel Ring (13). Thread on the Hole Saw-see Figure 1 B.
93421-Using the 1/4” Mandrel with 1-1/8”, 7/8” and 3/4”

The 1-1/8” Hole Saw, the 7/8” and the 3/4” can only be used with the 1/4” Mandrel.
1.

Thread the Hole Saw down onto the Mandrel.
Mounting to the Drill

1.

After attaching the Hole Saw to the desired Mandrel, the Hole Saw is now ready to be
mounted to the drill. Read the drill owner’s manual for instructions on properly mounting drill
bits.

2.

Before using the Hole Saw, make certain that the work piece is firmly clamped in place.
Mark the center of the hole to be drilled using a centerpunch. Place the drill bit in the
centerpunch impression, and slowly begin drilling into the workpiece. Always hold the drill
firmly with both hands to ensure safe operation of the Hole Saw.
Maintenance

1.

Check the Hole Saw and Mandrel before each use. Make certain that the Hole Saw is tightly
in place and that no part is worn or damaged.

2.

Clean the Metal Hole Saws after each use. Remove any debris, grease, oil and dirt.

3.

Store in the Blow Mold Case in a secure place out of the reach of children.
Parts List-93420-Electrician

Part #
1
2
3
4
5
6
7

Description
Quantity Part # Description
Quantity
Saw 7/8”D x 2”H
1
8
Pilot Bit-1-7/8” L x 1/4”1
Saw 1-1/8”D x 2” H 1
9
Mandrel-1/4”
1
Saw-1-3/8” D x 2” H 1
10
Mandrel-7/16”
1
Saw-1-3/4”Dx1-3/4”H 1
11
Mandrel Adapter
1
Saw-2”D x 1-3/4” H 1
12
Blow Mold Case
1
Saw 2-1/2”Dx1-3/4”H 1
13
Mandrel Ring
1
Pilot Bit-2-1/8”Lx1/4”D1
Parts List-93421-Plumber

Part #
1
2
3
4
5
6

Description
Quantity
Saw 3/4” D x 2” H
1
Saw 7/8” D x 2” H
1
Saw-1-1/8” D x 2” H 1
Saw-1-1/2”Dx1-3/4”H 1
Saw-1-3/4” Dx1-3/4”H1
Saw 2-1/4” x 1-3/4” H 1

SKU 93420/93421

Part #
8
9
10
11
12
13

Description
Quantity
Pilot Bit-1-7/8” L x 1/4”1
Mandrel-1/4”
1
Mandrel-7/16’
1
Mandrel Adapter
1
Blow Mold Case
1
Mandrel Ring
1

For technical questions please call 1-800-444-3353.

Page 5

Parts Diagram
6

5

10
8
9

7

4

11

3

13

2

1

#12-Blow Mold Case not shown
Note: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A
REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR
WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT
OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE
UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL
RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT
PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Figure 2-Maximum RPMs
Size

Mild Steel

3/4”
7/8”
1-1/8”
1-3/8”
1-1/2”
1-3/4”
2”
2-1/4
2-1/2”

SKU 93420/93421

460
390
325
285
230
195
170
150
135

Stainless Steel Cast Iron

230
195
155
145
115
95
85
75
65

300
260
205
190
150
130
115
100
90

Brass

600
520
415
380
300
250
230
200
180

Aluminum

690
585
465
425
345
295
255
225
205

For technical questions please call 1-800-444-3353.

Page 6



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Modify, Copy, Annotate, Fill forms, Extract, Assemble, Print high-res
Modify Date                     : 2005:09:06 13:44:22-06:00
Create Date                     : 2005:09:06 13:44:08-07:00
Author                          : mnix
Subject                         : 93420 93421 Bi Metal Hole Saws
Page Count                      : 6
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:db09e3d6-082a-426c-bd1c-d9744bb5e06c
Producer                        : Acrobat Distiller 6.0 (Windows)
Keywords                        : 
Creator Tool                    : Adobe PageMaker 7.0
Document ID                     : uuid:db8b08b3-e712-4729-a334-02d43c74008d
Format                          : application/pdf
Description                     : 93420 93421 Bi Metal Hole Saws
Title                           : 93420 93421 Bi Metal Hole Saws
Creator                         : mnix
EXIF Metadata provided by EXIF.tools

Navigation menu