Drive Medical Design Camping Equipment As 5000 Users Manual ~9101046
AS 5000 to the manual 35647024-ae25-4fc6-a8cb-01cc519b5f93
2015-02-04
: Drive-Medical-Design Drive-Medical-Design-Drive-Medical-Design-Camping-Equipment-As-5000-Users-Manual-514790 drive-medical-design-drive-medical-design-camping-equipment-as-5000-users-manual-514790 drive-medical-design pdf
Open the PDF directly: View PDF 
.
Page Count: 8
15
Drive Medical Design & Manufacturing
99 Seaview Boulevard
Port Washington, NY 11050
Toll Free: 877-224-0946
Local: 516-998-4600
www.drivemedical.com
746002-5150 V1.0
Instruction Manual
PLEASE READ ALL INSTRUCTIONS BEFORE USE.
Low air loss/Alternating pressure mattress
REV2.12.17.13
1
CONTENTS
IMPORTANT SAFEGUARDS...................................................... 2
1. INTRODUCTION .................................................................... 3
2. PRODUCT DESCRIPTION ..................................................... 4
3. INSTALLATION ....................................................................... 5
4. OPERATIONS ......................................................................... 7
5. CLEANING.............................................................................. 8
6. MATTRESS STORAGE .......................................................... 9
7. MAINTENANCE ...................................................................... 9
8. TECHNICAL DESCRIPTION ................................................ 10
APPENDIX A: EMC INFORMATION ......................................... 12
14
a/ The ISM (industrial, scientific and medical) bands between 150 kHz and 80 MHz are 6,765 MHz to 6,795
MHz;13,553 MHz to 13,567 MHz; 26,957 MHz to 27,283 MHz; and 40,66 MHz to 40,70 MHz.
b/ The compliance levels in the ISM frequency bands between 150 kHz and 80 MHz and in the frequency ran
g
e 80
MHz to 2.5 GHz are intended to decrease the likelihood that mobile/portable communications equipment could
cause interference if it is inadvertently brought into patient areas. For this reason, an additional factor of 10/3 is
used in calculating the recommended separation distance for transmitters in these frequency ranges.
c/ Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land
mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with
accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey
should be considered. If the measured field strength in the location in which the device is used exceeds the
applicable RF compliance level above, the device should be observed to verify normal operation. If abnormal
performance is observed, additional measures may be necessary, such as reorienting or relocating the device.
d/ Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.
Recommended separation distances between portable and mobile RF
communications equipment and this device:
This device is intended for use in an electromagnetic environment in which radiated RF disturbances are
controlled. The customer or the user of this device can help prevent electromagnetic interference by
maintaining a minimum distance between portable and mobile RF communications equipment
(transmitters) and this device as recommended below, according to the maximum output power of the
communications equipment
Rated maximum
output power
of transmitter
W
Separation distance according to frequency of transmitter m
150 kHz to 80 MHz
Pd 2.1
80 MHz to 800 MHz
Pd 2.1 800 MHz to 2,5 GHz
Pd 3.2
0.01 0.12 0.12 0.23
0.1 0.38 0.38 0.73
1 1.2 1.2 2.3
10 3.8 3.8 7.3
100 12 12 23
For transmitters rated at a maximum output power not listed above, the recommended separation distance
d
in
meters (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the
maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer.
Note 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
Note 2: These guidelines may not apply in all situations. Electromagnetic propa
g
ation is affected by absorption and
reflection from structures, objects, and people.
13
Guidance and Manufacturer’s Declaration - Electromagnetic Immunity:
This device is intended for use in the electromagnetic environment specified below. The user of this
device should make sure it is used in such an environment.
Immunity Test IEC60601 test level Compliance Electromagnetic Environment-Guidance
Conducted RF
IEC 61000-4-6
Radiated RF
IEC 61000-4-3
3Vrms150 kHz to 80
MHz outside ISM
bandsa
3 V
/
m 80 MHz to 2.5
GHz
3 Vrms
3 V/m
Portable and mobile RF communications
equipment should be used no closer to
any part of this device, including cables,
than there commended separation
distance calculated from the equation
applicable to the frequency of the
transmitter.
Recommended separation distance
Pd 2.1 150kHz to 80MHz
Pd 2.1 150kHz to 80MHz
Pd 3.280 MHz to 2.5G MHz
Where P is the maximum output power
rating of the transmitter in watts (W)
accordin
g
to the transmitter manufacturer
and d is the recommended separation
distance in meters (m).b
Field stren
g
ths from fixed RF transmitters,
as determined by an electromagnetic site
survey c, should be less than the
compliance level in each frequency
ranged.
Interference may occur in the vicinity of
equipment marked with the following
symbol:
NOTE 1: At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption
and reflection from structures, objects and people.
2
IMPORTANT SAFEGUARDS
READ ALL INSTRUCTIONS BEFORE USE
DANGER - To reduce the risk of electrical shock:
1. Always unplug this product immediately after using.
2. Do not use while bathing.
3. Do not place or store product where it can fall or be pulled into a tub or sink.
4. Do not place in or drop into water or other liquids.
5. Do not reach for a product that has fallen into water. Unplug immediately.
WARNING - To reduce the risk of burns, electrical shock, fire, or injury:
1. This product should never be left unattended when plugged in.
2. Close supervision is necessary when this product is used by, on, or near children or invalids.
3. Use this product only for its intended use as described in this manual.
4. Do not use attachments not recommended by the manufacturer.
5. Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been
dropped or damaged, or exposed to water. Return the product to a service center for examination
and repair.
6. Keep the cord away from heated surfaces.
7. Never block the air openings of this product. Never place the product on a soft surface, such as a bed
or couch, where the air openings may become blocked. Keep the air openings free of lint, hair, and
other similar particles.
8. Never drop or insert any object into any opening or hose on this product.
9. Connect this product to a properly grounded outlet only. See Grounding Instructions.
NOTEs, CAUTIONs AND WARNINGs:
NOTE - Calls attention to useful information, tips, reminders.
CAUTION - Calls attention to correct operating or maintenance procedures in order to prevent
damage to or destruction of the equipment or other property.
WARNING - Calls attention to a potential danger that requires correct operating procedures or
practices in order to prevent personal injury.
SYMBOL Definitions
Authorized representative in the European community.
Manufacturer
Complies with standards protecting against electric shock for type BF equipment.
Attention, you should read the accompanying information carefully!
Attention – Observe proper Disposal of Electrical & Electronic Equipment (WEEE):
This product should be handed over to an appropriate collection point for the recycling of
electrical and electronic equipment. For more detailed information about the recycling of
this product, please contact your local city office, household waste disposal service or the
retail store where you purchased this product.
Consult operating instructions
Class II
Functional earth.
3
1. INTRODUCTION
This manual should be used for initial set up of the system and for reference purposes.
1.1 GENERAL INFORMATION
This system is a high quality, affordable mattress system, suitable for the treatment and prevention of
pressure ulcers. This product has been tested and successfully approved for the following standards:
FOR US AND CANADA ONLY
Le produit à été testé avec des équipements médicaux et respecte les normes UL 60601-1 & CAN/CSA
C22.2 No.601.1. prévenant les choc électrique, le feu et les risques de blessures physiques.
1.2 INTENDED USE
This product is intended:
to help and reduce the incidence of pressure ulcers while optimizing patient comfort.
for long term home care of patients suffering from pressure ulcers.
for pain management as prescribed by a physician.
NOTE: This equipment is not suitable for use in the presence of flammable anesthetic
mixture with air or with pure oxygen or nitrous oxide.
NOTE: L’équipement ne peut être utilisé s’il y a risque de mélange d’un anesthésique
inflammable avec l’air ou l’oxygène ou oxyde nitreux.
EN 60601-1
EN 60601-1-2
EN 55011 Class B
IEC61000-3-2
IEC 61000-3-3
Medical Equipment-Air Pump
with respect to electrical shock, fire and
mechanical hazards only in accordance with
UL60601-1 AND CAN/CSA C22.2 NO.601.1
E245395
53DG
12
APPENDIX A: EMC INFORMATION
Guidance and Manufacturer’s Declaration- Electromagnetic Emissions:
This device is intended for use in the electromagnetic environment specified below. The user of this
device should make sure it is used in such an environment.
Emissions Test Compliance Electromagnetic Environment-Guidance
Harmonic emissions
IEC61000-3-2 Class A The device is suitable for use in all establishments,
including domestic establishments and those directly
connected to the public low-voltage power supply
network.
Voltage fluctuations /
Flicker emissions
IEC61000-3-3
Complies
Guidance and Manufacturer’s Declaration- Electromagnetic Immunity:
This device is intended for use in the electromagnetic environment specified below. The user of this
device should make sure it is used in such an environment.
Immunity Test IEC60601
test level Compliance Electromagnetic
Environment-Guidance
Electrostatic Discharge (ESD)
IEC61000-4-2 ±6kV contact
±8kV air
±6kV contact
±8kV air
Floors should be wood, concrete or
ceramic tile. If floors are covered
with synthetic material, the relative
humidity should be at least 30%.
Electrical fast transient/ burst
IEC61000-4-4
±2kV for power
supply line
±1kV for input/out
line
±2kV for power
supply line
±1kV for input/out
line
Mains power quality should be that
of a typical commercial or hospital
environment.
Surge
IEC61000-4-5
± 1 kV line(s) to
line(s)
± 2 kV line(s) to earth
± 1 kV line(s) to
line(s)
± 2 kV line(s) to earth
Mains power quality should be that
of a typical commercial or hospital
environment.
Voltage dips, short
interruptions and voltage
variations on power supply
input lines
IEC61000-4-11
<5 % UT (>95 % dip
in UT)for 0,5 cycle
40 % UT (60 % dip in
UT)for 5 cycles
70 % UT (30 % dip in
UT)for 25 cycles
<5 % UT (>95 % dip
in UT)for 5 sec
<5 % UT (>95 % dip
in UT) for 0,5 cycle
40 % UT (60 % dip in
UT) for 5 cycles
70 % UT (30 % dip in
UT) for 25 cycles
<5 % UT (>95 % dip
in UT) for 5 sec
Mains power quality should be that
of a typical commercial or hospital
environment. If the user of this
device requires continued operation
durin
g
power mains interruptions, it
is recommended that the device be
powered from an uninterruptible
power supply or a battery.
Power frequency
(50/60Hz) magnetic field
IEC61000-4-8
3 A/m 3 A/m
Power frequency magnetic fields
should be at levels characteristic of
a typical location in a typical
commercial or hospital environment.
NOTE: UT is the a.c. mains voltage prior to the application of the test level
11
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This product should be grounded. In the event of an electrical short circuit grounding reduces the risk of
electric shock by providing an escape wire for the electric current. This product is equipped with a cord
having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly
installed and grounded.
DANGER - Improper use of the grounding plug can result in a risk of electric shock.
If repair or replacement of the cord or plug is necessary, do not connect the grounding wire to either flat
blade terminal. The wire with insulation having an outer surface that is green with or without yellow
stripes is the grounding wire.
NOTE - If the repair or replacement of the cord is necessary, please contact a qualified electrician or
serviceman. To reduce the risk of electric shock, do not modify the cord or plug in any way.
Check with a qualified electrician or serviceman if the grounding instructions are not completely
understood, or if in doubt as to whether the product is properly grounded.
4
2. PRODUCT DESCRIPTION
2.1 PUMP AND MATTRESS SYSTEM
2.2 PUMP UNIT
1. CPR Tags
2. Pump unit
3. Mattress unit
4. Quick Connector
Front View
1. Quick Connector Slot
2. Front Panel
Rear View
1. Power Switch
2. Power Cord
3. Bed Frame Hangers
1
2
3
1
2
5
3. INSTALLATION
Unpack the box and check the package contents for completeness.
Package Content List
n Mattress unit x 1 (may not be included if only pump unit is purchased)
n Pump Unit x 1
n User Manual x 1
Inspect equipment for damage which may have occurred during shipment. If there is damage, please
contact your dealer immediately.
3.1 PUMP & MATTRESS INSTALLATION
1. Place the mattress or pad on top of a bed frame.
Orient the mattress so that the foot-markers on the
mattress are situated towards the end of the bed
(where pump will be located).
2. Place the pump hangers over the bed railing at the
foot of the bed. Support the pump from the bottom
and turn the hangers outward (or inward) to secure
the pump against the railing.
If no bed railing is available, place the pump on a flat,
sturdy surface or on the floor, beneath the bed.
3. Connect the Quick Connector on the air hose (from
air mattress) to the pump unit Quick Connector Slot.
When you hear a "click", the connection will be
secured.
NOTE: Check and ensure the air hoses are
not kinked or tucked under the
mattress.
10
8. TECHNICAL DESCRIPTION
Specifications:
Item Specification
Power Supply (Note: See
rating label on the product) AC 100-120V 60 Hz, 0.16 A 14W (For 120V System)
Fuse Rating T1A, 250V
Cycle time Fixed, 8 min @ 60Hz,
Dimension (L x W x H) 29 x 18.5 x 12.6 (cm) or 11.4" x 7.3" x 5.0"
Weight 2.2 Kg or 5 lb
Environment
Temperature
Operation:10° C to 40° C (50° F to 104° F)
Storage: -15° C to 50° C (5° F to 122° F)
Shipping: -15° C to 70° C (5° F to 158° F)
Humidity
Operation: 10% to 90% non-condensing
Storage: 10% to 90% non-condensing
Shipping:10 % to 90% non-condensing
Classification
Class II with functional earth(NOTE:5*), Type BF, IPX0
Applied Part: Air Mattress
Not suitable for use in the presence of a flammable
anesthetic mixture (No AP or APG protection)
Mattress Specification
Model 8” Replacement
Dimension (L x W x H) 200 x 90 x 20.3 (cm)
or 78.7” x 35.4” x 8”
Weight 7.5 kg 16.5 lb
egnaR erusserP
NOTE: 1. Consult the distributor or EU representative for further technical documents.
2. These specifications are also applicable for other regions operating with the
same power supply.
3. The manufacturer reserves the right to modify the specifications without notice.
4. The earthing terminal is served as functional earth, not protective earth.
Adjustable Weight Settings
9
6. MATTRESS STORAGE
1. Lay the mattress on a flat surface, upside-down.
2. Roll-up the mattress starting from the head until you reach the foot of the mattress.
3. Use the straps at the end of the mattress and stretch them around the mattress to prevent it from
unraveling.
Note: Do not fold, crease or stack the mattresses.
7. MAINTENANCE
7.1 GENERAL
1. Check the main power cord and plug for abrasions or excess wear.
2. Check the mattress cover for signs of wear or damage.
3. Disconnect the air tube from the mattress. Then check the airflow coming from the two air outlets
on the pump. They should be alternately delivering air when the pump is set at “alternate” mode.
4. Check the air hoses for kinks or breaks. For replacement, please contact your local distributor.
6
4. Plug the power cord into a electrical outlet with the
appropriate voltage.
NOTE: The pump unit must be suitable for the
local power voltage.
NOTE: S’assure que la pompe est compatible
au voltage local ou disponible.
6. Turn the main power switch (on pump) to the ON
position. After you turn on power to the pump, you
will have to wait at least 20 minutes for the mattress
to become fully inflated.
The low pressure indicator (yellow LED) will
illuminate while the mattress is pressurizing.
When the appropriate pressure is reached, the Low
Pressure indicator (yellow LED) will go off and the
Normal Pressure indicator (green LED) will illuminate.
The bed is now ready for use.
NOTE: You can unplug the unit to power-off the device.
NOTE: L’appareil est également muni d’une fiehe de connexion à l’électricité.
CAUTION: The pump supplied with the mattress can only be used for mattresses recommended
by the manufacturer. Do not use it for any other purpose. (applied part: air mattress)
AVERTISSEMENT : La pompe ne peut être utilisée qu’avec le matelas designé ou r
recommandé par le manufactureier,. Ne pas server d’ysage autre que celui auquel
elle a été conçu
NOTE: (For models WITHOUT the low-air-loss function) During power outages, you can
cover the Quick Connector with the transport cap to maintain air pressure inside the
air cells.
NOTE: After installation, make sure any excess cord or tubing is removed from possible foot
traffic to avoid accidental tripping. All EQUIPMENT should be positioned to always
allow unhindered patient access by physicians and caregivers.
ON
7
4. OPERATIONS
NOTE: Always read the operating instructions before use.
4.1 PANEL OPERATIONS
1. Pressure Adjustment Knob
The pressure adjustment knob controls the air pressure in the mattress. Turning the knob clockwise
will increase the pressure; counter-clockwise decreases the pressure. Higher pressures will support
heavier patients. The pressure should be adjusted according to individual comfort preferences.
When the mattress is finished pressurizing to the desired level of firmness, the Normal Pressure
LED indicator will illuminate.
NOTE: You can also check if the pressure is suitable for the patient by sliding one hand
beneath the air cells at the level of the patient's buttocks. The air cells will alternately inflate
and deflate. You should feel slight contact with the buttocks when the air cells beneath the
buttocks deflate.
NOTE: Every time the mattress is initialized (inflated), it is recommended that you set the
pressure knob to "Max" to hasten inflation. You can then adjust the air mattress to the desired
firmness later.
2. Normal Pressure Indicator
When the green LED illuminates, the pressure inside of air mattress has reached the desired
pressure setting (preset on the Pressure Adjustment Knob).
3. Low Pressure Indicator
When the mattress is initializing, the Low Pressure LED will illuminate until the appropriate pressure
is reached (according to the Pressure Adjustment Knob); this is normal. Otherwise, the Low
Pressure LED is a warning, indicating that the pressure in mattress is unusually low. Check to
ensure all connections are secured and correctly installed as per the installation instructions.
4
2 3
1
8
NOTE: If the pressure level is consistently low, check for any leakage (tubes or air hoses). If
necessary, replace any damaged tubes or hoses or contact your local qualified dealer
for repair.
4. Alternate / Static Switch
The ALTERNATE/STATIC switch selects between Alternate Pressure mode and Static Pressure
mode. With Alternate Pressure mode, alternating air cells are partially deflated and inflated,
avoiding prolonged pressure on any single point beneath the patient; this is to prevent pressure
ulcers. With Static Pressure mode, all of the air cells are equally inflated.
4.2 Emergency CPR Operations
CPR must be performed on a firm surface. Therefore, if an
emergency CPR situation occurs with the patient on the
mattress, the mattress must be quickly deflated. This is
done by quickly pulling on the CPR tag located at the head
of the mattress on the patient’s right-side. The quick
connector found from the pump unit can also be
disconnected to hasten deflation.
5. CLEANING
It is important to follow the cleaning procedures before first-time use with any patient; this is to avoid the
possibility of transmission of pathogens between patients and caregivers.
Wipe down the pump unit with a damp cloth pre-soaked with a mild detergent. Avoid contact with dust
and proximity to dusty areas. Make sure that any cleaning agents you use will not harm or corrode the
plastic casing on the pump unit.
CAUTION: Do not immerse or soak the pump unit in liquids.
Wipe-down the mattress unit with a damp cloth pre-soaked with warm water (do not exceed 65 ℃)
containing a mild detergent. Avoid dust and proximity to dusty areas. The cover may also be cleaned
using sodium hypochlorite diluted in water. All components should be air dried thoroughly before use.
CAUTION: Do not use phenolic based products for cleaning.
CAUTION: Do no dry the mattress in direct sunlight.
The carrying bag (if available) should be turned inside-out and completely wiped-down using
disinfectant solutions. Allow it to air-dry thoroughly and then turn it back and wipe down the outside of
the bag with disinfectant solutions.
