Dynabook DCE45380A Tri-Mode Dual-Band Analog/PCS Phone User Manual CDM9155GPXFCC cover

Download:
Mirror Download [FCC.gov]
Document ID	183462
Application ID	zs619E/aL8V5MMIhPv2ESQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	23.05kB (288184 bits)
Date Submitted	2001-12-13 00:00:00
Date Available	2002-01-04 00:00:00
Creation Date	2001-11-28 18:37:47
Producing Software	Acrobat PDFWriter 4.0 Windows
Document Lastmod	2001-12-07 13:48:36
Document Title	æ©¡CDM9155GPXFCC_cover.PDF
Document Creator	æ©¡Microsoft Word
Document Author:	æ©¡ogi

APPLICANT: TOSHIBA CORPORATION
TRANSCEIVER TYPE: CJ6DCE45380A
9155GPX
OWNER'S MANUAL
Draft
December 2001
TABLE OF CONTENTS
SAFETY INFORMATION FOR
WIRELESS HANDHELD PHONES ...........…………........... 1
SAR INFORMATION ......................................…………....... 2
FUNCTIONS .............................................…………............. 3
GETTING STARTED ................................…………............. 5
BASIC OPERATION .......................................…………....... 6
Placing Calls .......................................………….............. 6
Receiving Calls ................................…………................. 8
During Calls..........................................…………............. 9
Standby.................................................…………............. 11
OPERATING PROCEDURES ........................…………....... 12
EXHIBIT Type “User Manual”
SAFETY
SAFETY INFORMATION
INFORMATION FOR
FOR
WIRELESS
WIRELESS HANDHELD
HANDHELD PHONES
PHONES
Read this information before using your handheld
portable Cellular Telephone.
Your wireless handheld portable telephone is a low
power radio transmitter and receiver. When it is ON, it
receives and also sends out radio frequency (RF) signals.
FCC RF EXPOSURE INFORMATION
In August 1996, the Federal Communications Commission (FCC) of the United States, with its action in Report and Order FCC 96-326, adopted an updated safety
standard for human exposure to radio frequency (RF)
electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety
standard previously set by both U.S. and international
standards bodies. The design of this phone complies
with the FCC guidelines and these international standards.
Use only the supplied or an approved antenna. Unauthorized antennas, damaged antennas, modifications,
or attachments could impair call quality, damage the
phone, or result in violation of FCC regulations. Please
contact your local dealer for replacement antenna.
Body-worn Operation
This device was tested for typical body-worn operations
with the BC-9100 belt-clip and LB-9100 holster models, offered by Audiovox as an accessory to this phone,
and found to comply with FCC RF exposure requirements. Third-party belt-clips, holsters and similar accessories should be avoided, as they have not been
tested and may not comply with FCC RF exposure limits.
For more information about RF exposure, please visit
the FCC website at www.fcc.gov .
SAR
SAR INFORMATION
INFORMATION
THIS MODEL PHONE MEETS THE GOVERNMENT’S REQUIREMENTS FOR EXPOSURE TO RADIO WAVES.
Your wireless phone is a radio transmitter and receiver. It is
designed and manufactured not to exceed the emission limits
for exposure to radiofrequency (RF) energy set by the Federal Communications Commission of the U.S. Government.
These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population.
The guidelines are based on standards that were developed
by independent scientific organizations through periodic and
thorough evaluation of scientific studies. The standards include
a substantial safety margin designed to assure the safety of
all persons, regardless of age and health.
The exposure standard for wireless mobile phones employs a
unit of measurement known as the Specific Absorption Rate,
or SAR. The SAR limit set by the FCC is 1.6 W/kg.* Tests for
SAR are conducted with the phone transmitting at its highest
certified power level in all tested frequency bands. Although the
SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below
the maximum value. This is because the phone is designed to
operate at multiple power levels so as to use only the power
required to reach the network. In general, the closer you are to
a wireless base station antenna, the lower the power output.
Before a phone model is available for sale to the public, it
must be tested and certified to the FCC that it does not exceed the limit established by the government-adopted requirement for safe exposure. The tests are performed in positions
and locations (e.g., at the ear and worn on the body) as required by the FCC for each model. The highest SAR value for
this model phone when tested for use at the ear is 1.45 W/kg
and when worn on the body, as described in this user guide,
is 0.72 W/kg. (Body-worn measurements differ among phone
models, depending upon available accessories and FCC requirements). While there may be differences between the SAR
levels of various phones and at various positions, they all meet
the government requirement for safe exposure.
The FCC has granted an Equipment Authorization for this
model phone with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model phone is on file with the FCC and can be
found under the Display Grant section of http://www.fcc.gov/
oet/fccid after searching on FCC ID CJ6DCE45380A.
Additional information on Specific Absorption Rates (SAR) can
be found on the Cellular Telecommunications & Internet Association (CTIA) web-site at http://phonefacts.net.
In the United States and Canada, the SAR limit for mobile
phones used by the public is 1.6 watts/kg (W/kg) averaged
over one gram of tissue. The standard incorporates a substantial margin of safety to give additional protection for the
public and to account for any variations in measurements.
FUNCTIONS
FUNCTIONS
External View
Retractable
Whip Antenna
Power
Indicator
Receiving
Signal
Strength
Indicator
Earpiece
Digital
Mode
Indicator
IN USE
Indicator
Incoming Call
& Charging
Indicator (LED)
Roaming
Indicator
Message
Indicator
Earphone
Mic Jack
Vibrating
Indicator
Battery Level
Indicator
Soft Key 1
Rm
ABCDEFGHIJKL
MNOPQRSTUVWX
YZ1234567890
Graphic
Display
Send Key
Soft Key 2
Message
Access Key
One-Touch
Emergency Key
Digit Keys
End Key with
Power On/Off
Rcl F
Voice Mail &
Speakerphone
CLR
2ABC
3DEF
4 GHI
5JKL
6 MNO
7PQRS
8TUV
9WXYZ
Multi Function
Key
Up-arrow
Recall
Function
Down-arrow
Clear Key
Vibrating &
Shift Key
Voice Activated
Dialing &
Space Key
Next Key
Microphone
Power/Data
Connector
Function of Keys
Digit Keys
2ABC
3DEF
4 GHI
5JKL
6 MNO
7PQRS
8TUV
9WXYZ
To enter Telephone Numbers.
To enter letters and symbols (see
page 32).
is also used for One-Touch
Emergency feature.
Function Keys
Rcl F
Key- Board Arrangement
CLR
Soft Keys. To function as shown in the
bottom line on the display.
SEND Key. To originate or answer a call.
Rcl
CLR
END Key. To terminate a call and to turn
the phone ON/OFF.
To recall phone numbers from memory.
Also used as left-arrow key.
To be used with other keys to activate
various special features. Also used as
right-arrow key.
To control the volume of Ringer, Key Tone
and Earpiece/Speakerphone.
Also used as up/down-arrow keys.
To access your Voice Mail with only one
key (see page 62) and to activate Speakerphone mode (see page 29).
To review Text Messages or to learn how
many Voice Messages are in your Voice
Mailbox (see page 57).
To clear digits from the display or from a
memory location.
LCD Display Indication
Items
Descriptions
Receiving Signal Strength Indicator.
The number of lines indicates the received
Signal Strength, and is also used as a
POWER ON Indicator.
Digital Mode Indicator. To indicate the
phone is operating in digital mode.
A call is in progress.
The phone is out of Service Area.
Rm
The phone is out of the Home Area.
Message Indicator. To indicate that new
Text Messages are stored in memory or new
Voice Messages are in your Voice Mailbox.
Vibrating Indicator. To indicate that the
vibrating alert is active.
Battery Level Indicator.
Monitors the battery charge condition.
ABCDEFGHIJKL Graphic full-dot matrix display with flexible
MNOPQRSTUVWX font size in 3 to 7 lines.
YZ1234567890
GETTING
GETTING STARTED
STARTED
Turning the Phone On/Off
Press and hold
. All the indicators and the display
will light momentarily, and a tone will be heard. The
indicator will be displayed while the phone is on.
To turn the phone off, press and hold
Antenna Position
The antenna can be used in its fully extended or fully retracted position only. It is recommended that the antenna
should be fully extended for optimum performance and
signal strength or while operating in poor signal areas.
Receiving Signal Strength Indicator (
The number of lines shown by this icon indicates the
strength of the signal your phone is receiving. Four lines
indicates maximum signal strength. The number of lines
may change as you move with the phone to represent
the changing signal strength. If the signal is not strong
enough to place a call, “ ” will appear on the display.
Battery Level Indicator
You can always monitor the battery charge condition
with the constant battery level indicator. The number of
blocks indicates the battery conditions as follows:
Full charge
Low charge
Flashing indicates discharged.
BASIC
BASIC OPERATION
OPERATION
Placing Calls
To Place a Call
1. Enter the phone number.
(A maximum of 32 digits will
be displayed.)
123-456-7890
STO
2. Press
indicator will appear
The
on the display.
Menu
Calling...
123-456-7890
• To Correct a Number
Press CLR to clear the last digit.
Press and hold CLR to erase all the digits entered.
• If the Call Fails to Go Through
Press
and
to redial the number.
To Terminate a Call
Press
display.
. The
indicator will no longer appear in the
Last Number Redial
1. Press the key under Redial , or press Rcl
to
recall the last number dialed.
to place the call.
2. Press
See Call History on page 54 for details. See also Redial Soft Key (F04) on page 89.
To Dial the Last Number Received
Press Rcl
to recall the last number with Caller ID
you received, then press
See Call History on page 54 for details.
Phonebook Dialing
Press Rcl and enter an address (01 to 99) to recall a
number from your phonebook, then press
See Phonebook Recall on page 43 for details.
Tip:
The
key will be used for Voice Mail access. See
page 62.
Tip:
Press and hold
for Voice Activated Dialing. See
page 53.
Speed Dialing
If you know the phonebook address of the telephone
number that you want to call, you may place a call without using Rcl .
1. Enter the one or two digits of your Phonebook address (1 to 9 or 10 to 99).
. The phone number will be displayed.
2. Press
indicator will be displayed and the call will
The
be placed.
Note: If two telephone numbers are stored in the address,
the Primary Number will be dialed.
Quick Dialing
When this feature is on, the Primary number in your
Phonebook address 02 to 09 can be dialed with just
one push of the key. See Quick Dialing (F01) on page
89 to turn this feature on/off.
1. Press a digit key ( 2 to 9 ) for more than one
second.
2. The number in your phonebook is automatically
dialed. The phone number will be displayed. The
indicator will light.
ABC
Note: The key 1
WXYZ
is not for Quick Dialing, but for One-
Touch Emergency Call, page 27.
Emergency Call
This feature permits you to place an emergency call even
if your telephone is in “Phone Lock”, “Keypad Lock” or
“Restrict” mode. Up to 3 numbers can be programmed as
Emergency numbers. The emergency numbers “911” and
“ 911” are already preprogrammed. See To Change
Emergency Numbers (F62) on page 85.
Example: To Call 911 in “Phone Lock” or “Keypad Lock” mode.
1 . The “911” will not be dis1. Enter 9
played.
2. Press
The “911” will be displayed. Calling...
indicator will light,
The
and the call will be placed. Emergency
911
WXYZ
One-Touch Emergency Call
This feature permits you to dial an emergency number
by a single key stroke, even in the “Phone Lock” or
“Restrict” mode. This feature can be turned off to prevent unintentional calls to the emergency number.
See To Turn On/Off One-Touch Emergency Call Feature (F63) on page 85.
1. Press and hold 1 for more than 2 seconds. The
number in emergency memory location “1” will be
dialed.
indicator will be displayed and the
2. Then the
call will be placed. (The factory preset number is
“911”.)
Note: This feature cannot be used if the Keypad Lock is on.
You need to dial all the digits and
Emergency Call Mode
When you dial one of the 3 preprogrammed emergency
numbers, your phone will enter the Emergency Call
Mode. In this mode, the phone will attempt to complete
the emergency call using any available cellular system
from which it can obtain service.
After it places an emergency call, the phone will stay in
the Emergency Call Mode, and will display “Emergency Call Mode, END to exit”. In the Emergency Call
Mode, the phone will attempt to continue to receive
service from the Cellular system that it used to complete the call. The phone will automatically exit the
Emergency Call Mode after 5 minutes or after you
press
Receiving Calls
The phone sounds an alert or vibrates to alert you of
an incoming call. The phone sounds an alert or vibrates
to alert you of an incoming call. Also, the LED on the
top of the phone will flash.
To Receive a Call
When the telephone rings, press
indicator will be displayed.
The
to answer the call.
Note: To mute the ringer or stop the vibrating, press
Any Key Answering
This feature permits you to answer an incoming call by
and Rcl F .
pressing any key on the key pad except
Caller ID with Name
This feature allows you to preview in your display the
number and name of the party calling you before you
answer the call. The name is as you programmed it in
your phonebook.
1. When the phone rings, the Incoming Call
Calling Number appears in
JACK
the display.
123-456-7890
2. The last 10 Caller IDs are stored in the memory
for your review and redial. See Call History on
page 54 for details.
Note: “Number Restricted” or “Number Unavailable” is displayed when the Caller ID is restricted or not available.
Automatic Calls-in-Absence Indicator
This feature indicates the number of unanswered incoming calls. The display indicates “Called XX”, the number of calls (01 to 99) you missed and the LED will blink.
It also indicates the caller number and name of the latest
call, if available. Press the key under Refer to view Incoming Call History.
Called 12
May 21 10:25 am
Depressing any key will clear the JACK
123-456-7890
display. See Redial Soft Key
Refer
(F04) on page 89.
Ringing Tone with Melody
The 9155GPX offers you 15 styles of ringer tones and
melodies for alerting incoming calls. Ringer volume can
also be adjusted. See Ringer Type Selection (F32) on
page 75 and Ringer Volume Control (F31) on page 75
for setting. See also Vibrating Alert (F8) on page 88.
Distinctive Ringing (Audible Caller ID)
You may program different ringer styles for different
phonebook addresses. See To Store a Ringer Type
with the Phone Number on page 40 for setting.
During Calls
To Adjust the Earpiece Volume
Simply press
or
to adjust Earpiece/Speakerphone
Volume during a call.
Ear/SPK Vol.
To Mute a Phone Conversation
There are two ways to mute the microphone during a
call.
F .
1. Press the key under Mute , or press
2. Then the screen displays “Phone is muted!”.
3. To return to normal mode, press the key under
F again.
Unmute , or press
Note: Terminating a call cancels the muting.
Speakerphone Mode (Two-Way)
This feature allows you to engage in a conversation without having to hold the phone.
1. To activate this feature, press V
during a call.
The screen displays “Speaker ON!”.
or
to adjust the earpiece/speak2. Press
erphone volume.
3. To return to normal mode, press V
again.
Notes: 1. Terminating a call cancels the speakerphone mode.
2. It is not recommended to use this feature in a noisy
environment.
Automatic Talk Timer
The talk time of the current call will be automatically
displayed. For example, “1H 23M 45S”.
Scratch Pad Dialing
If you enter a telephone number during a call, the number will be stored in the Scratch Pad memory.
After terminating the call, the number you entered can
be dialed by pressing
Note: You can deactivate “Sending DTMF” so that keypad
tones will not be transmitted to the calling party. See
Sending DTMF (F34) on page 75.
Call Waiting
Your service provider may provide Call Waiting service.
When you are on a call, you may hear a beep tone alerting you of another incoming call.
Your phone displays “New Caller” and the new caller’s
name and number. The name is as you programmed it
in your phonebook.
to answer the new call.
1. Press
again to switch between the two calls.
2. Press
10
Three-Way Calling
Your service provider may provide Three-Way Calling
service. When a call is already in progress, you may
call the third party.
1. Enter a number and press
to call the third
party.
again to connect all three parties.
2. Press
Ask your service provider for the detailed information.
Standby
Indicators on Standby
Your phone displays date and
time, various settings status, and
soft keys in standby.
May 21 Mon
3 : 15 pm
Redial
Web
Ringer Volume is in Silent mode. See page 75.
Automatic Answering is active. See page 89.
Phone Lock is active. See page 72.
Keypad Lock is active. See page 71.
Countdown Timer is active. See page 80.
Clock Alarm is active. See page 79.
Redial : See Last Number Redial on page 25.
Web : See Accessing Internet on page 65.
Note: For displaying date and time, see Clock Indicator (F42)
and Clock Adjustment (F43) on page 79.
Vibrating Alert
To activate Vibrating Alert, press and hold
. The
indicator will be displayed. To deactivate it, press
and hold
again. See also Vibrating Alert (F8) on
page 88.
Multilingual
Your phone provides multiple languages (English, Spanish, French and Portuguese) for displaying the menus
and prompts in the Basic Operation, Phonebook Operation and Function Menu. See Language Selection
(F24) on page 74.
11
OPERATING
OPERATING PROCEDURES
Never violate any of the following Rules and Regulations of the FCC when using your Cellular Phone. Such
violations are punishable by fine, imprisonment or both.
• Never use obscene, indecent, or profane language.
• Never use your Cellular Phone to send false distress calls.
• Never wiretap or otherwise intercept a phone call,
unless you have first obtained the consent of the
parties participating in the call.
• Never make any anonymous calls to annoy, harass, or molest other people.
• Never charge another account without authorization, to avoid payment for service.
• Never willfully or maliciously interfere with any
other radio communications.
• Never refuse to yield the line when informed that
it is needed for an Emergency Call. Also, never
take over a line by stating falsely that it is needed
for an emergency.
12

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Creator                         : .橡.Microsoft Word
Create Date                     : 2001:11:28 18:37:47
Title                           : .橡.CDM9155GPXFCC_cover.PDF
Author                          : .橡.ogi
Producer                        : Acrobat PDFWriter 4.0 Windows
Modify Date                     : 2001:12:07 13:48:36+09:00
Page Count                      : 13

EXIF Metadata provided by EXIF.tools