Dynabook UPA3234WL 802.11a/b MINIPCI TYPE 3B CARD User Manual cvr imo100 01

Toshiba Corporation 802.11a/b MINIPCI TYPE 3B CARD cvr imo100 01

UserManual.wiki >

Dynabook >

UPA3234WL User Manual >

PotegeM200 User Manual HTML Version

PotegeM200 User Manual

TOSHIBA Portégé M200

Portable Personal Computer

User’s Manual

this manual cannot be reproduced in any form without the prior written permission

of TOSHIBA. No patent liability is assumed, with respect to the use of the informa-

tion contained herein.

TOSHIBA Portégé M200 Portable Personal Computer User’s Manual

First edition November 2003

Disclaimer

This manual has been validated and reviewed for accuracy. The instructions and

descriptions it contains are accurate for the TOSHIBA Portégé M200 Portable

Personal Computer at the time of this manual’s production. However, succeeding

computers and manuals are subject to change without notice. TOSHIBA assumes

no liability for damages incurred directly or indirectly from errors, omissions or

discrepancies between the computer and the manual.

Trademarks

IBM is a registered trademark of International Business Machines Corporation.

Intel, Pentium and Centrino are registered trademarks and SpeedStep is a trademark

of Intel Corporation.

Windows and Microsoft are registered trademarks of Microsoft Corporation.

Bluetooth is a trademark owned by its proprietor and used by TOSHIBA under

licence.

Other trademarks and registered trademarks not listed above may be used in this

manual.

FCC information

Product Name :

Portégé

M200

Model number :

PPM20

FCC notice "Declaration of Conformity

Information"

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installa-

tion. This equipment generates, uses and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interfer-

ence will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

❑Reorient or relocate the receiving antenna.

❑Increase the separation between the equipment and receiver.

❑Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

❑Consult the dealer or an experienced radio/TV technician for help.

WARNING: Only peripherals complying with the FCC class B limits may

be attached to this equipment. Operation with non-compliant peripher-

als or peripherals not recommended by TOSHIBA is likely to result in

interference to radio and TV reception. Shielded cables must be used

between the external devices and the computer’s external monitor port,

USB port and microphone jack. Changes or modifications made to this

equipment, not expressly approved by TOSHIBA or parties authorized by

TOSHIBA could void the user’s authority to operate the equipment. The

modular cable that comes with the computer must be used to connect a

modem.

FCC conditions

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that

may cause undesired operation.

Contact

Address: TOSHIBA America Information Systems, Inc.

9740 Irvine Boulevard

Irvine, California 92618-1697

Telephone: (949) 583-3000

EU Declaration of Conformity

TOSHIBA declares, that the product: PPM20* conforms to the following Standards:

Supplementary Information: “The product complies with the requirements of

the Low Voltage Directive 73/23/EEC, the EMC

Directive 89/336/EEC and/or the R&TTE Directive

1999/05/EEC.”

This product is carrying the CE-Mark in accordance with the related European

Directives. Responsible for CE-Marking is TOSHIBA Europe, Hammfelddamm 8,

41460 Neuss, Germany.

VCCI Class B Information

Modem warning notice

Conformity Statement

The equipment has been approved to [Commission Decision “CTR21”] for pan-

European single terminal connection to the Public Switched Telephone Network

(PSTN).

However, due to differences between the individual PSTNs provided in different

countries/regions the approval does not, of itself, give an unconditional assurance

of successful operation on every PSTN network termination point.

In the event of problems, you should contact your equipment supplier in the first

instance.

Network Compatibility Statement

This product is designed to work with, and is compatible with the following

networks. It has been tested to and found to conform with the additional require-

ments conditional in EG 201 121.

Germany ATAAB AN005,AN006,AN007,AN009,AN010 and

DE03,04,05,08,09,12,14,17

Greece ATAAB AN005,AN006 and GR01,02,03,04

Portugal ATAAB AN001,005,006,007,011 and P03,04,08,10

Spain ATAAB AN005,007,012, and ES01

Switzerland ATAAB AN002

All other countries/regions ATAAB AN003,004

Specific switch settings or software setup are required for each network, please refer

to the relevant sections of the user guide for more details.

The hookflash (timed break register recall) function is subject to separate national

type approvals. It has not been tested for conformity to national type regulations,

and no guarantee of successful operation of that specific function on specific

national networks can be given.

Japan regulations

Region selection

If you are using the computer in Japan, technical regulations described in the

Telecommunications Business Law require that you select the Japan region mode. It

is illegal to use the modem in Japan with any other selection.

Redial

Up to two redial attempts can be made. If more than two redial attempts are made,

the modem will return Black Listed. If you are experiencing problems with the

Black Listed code, set the interval between redials at one minute or longer.

Japan’s Telecommunications Business Law permits up to two redials on analogue

telephones, but the redials must be made within a total of three minutes.

The internal modem is approved by Japan Approvals Institute for Telecommunica-

tions Equipment.

A02-0604JP

Pursuant to FCC CFR 47, Part 68:

When you are ready to install or use the modem, call your local telephone company

and give them the following information:

❑The telephone number of the line to which you will connect the modem

❑The registration number that is located on the device

The FCC registration number of the modem will be found on either the device which

is to be installed, or, if already installed, on the bottom of the computer outside of

the main system label.

❑The Ringer Equivalence Number (REN) of the modem, which can vary. For the

REN of your modem, refer to your modem’s label.

The modem connects to the telephone line by means of a standard jack called the

USOC RJ11C.

Type of service

Your modem is designed to be used on standard-device telephone lines. Connec-

tion to telephone company-provided coin service (central office implemented

systems) is prohibited. Connection to party lines service is subject to state tariffs. If

you have any questions about your telephone line, such as how many pieces of

equipment you can connect to it, the telephone company will provide this informa-

tion upon request.

Telephone company procedures

The goal of the telephone company is to provide you with the best service it can. In

order to do this, it may occasionally be necessary for them to make changes in their

equipment, operations, or procedures. If these changes might affect your service or

the operation of your equipment, the telephone company will give you notice in

writing to allow you to make any changes necessary to maintain uninterrupted

service.

If problems arise

If any of your telephone equipment is not operating properly, you should immedi-

ately remove it from your telephone line, as it may cause harm to the telephone

network. If the telephone company notes a problem, they may temporarily discon-

tinue service. When practical, they will notify you in advance of this disconnection.

If advance notice is not feasible, you will be notified as soon as possible. When

you are notified, you will be given the opportunity to correct the problem and

informed of your right to file a complaint with the FCC. In the event repairs are ever

needed on your modem, they should be performed by TOSHIBA Corporation or an

authorized representative of TOSHIBA Corporation.

Disconnection

If you should ever decide to permanently disconnect your modem from its present

line, please call the telephone company and let them know of this change.

Fax branding

The Telephone Consumer Protection Act of 1991 makes it unlawful for any person

to use a computer or other electronic device to send any message via a telephone

fax machine unless such message clearly contains in a margin at the top or bottom

of each transmitted page or on the first page of the transmission, the date and time it

is sent and an identification of the business, other entity or individual sending the

message and the telephone number of the sending machine or such business, other

entity or individual. In order to program this information into your fax modem, you

should complete the setup of your fax software before sending messages.

Instructions for IC CS-03 certified equipment

1 The Industry Canada label identifies certified equipment. This certification

means that the equipment meets certain telecommunications network protective,

operational and safety requirements as prescribed in the appropriate Terminal

Equipment Technical Requirements document(s). The Department does not

guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be

connected to the facilities of the local telecommunications company. The

equipment must also be installed using an acceptable method of connection.

The customer should be aware that compliance with the above conditions may

not prevent degradation of service in some situations. Repairs to certified

equipment should be coordinated by a representative designated by the

supplier. Any repairs or alterations made by the user to this equipment, or

equipment malfunctions, may give the telecommunications company cause to

request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connec-

tions of the power utility, telephone lines and internal metallic water pipe system,

if present, are connected together. This precaution may be particularly important

in rural areas.

CAUTION: Users should not attempt to make such connections them-

selves, but should contact the appropriate electric inspection authority,

or electrician, as appropriate.

2 The user manual of analog equipment must contain the equipment’s Ringer

Equivalence Number (REN) and an explanation notice similar to the following:

The Ringer Equivalence Number (REN) of the modem, which can vary. For the

REN of your modem, refer to your modem’s label.

NOTICE: The Ringer Equivalence Number (REN) assigned to each

terminal device provides an indication of the maximum number of

terminals allowed to be connected to a telephone interface. The termina-

tion on an interface may consist of any combination of devices subject

only to the requirement that the sum of the Ringer Equivalence Numbers

of all the devices does not exceed 5.

3The standard connecting arrangement (telephone jack type) for this equipment is

jack type(s): USOC RJ11C.

The IC registration number of the modem is shown below.

Canada: 1353A-L4AINT

Notes for Users in Australia and New Zealand

Modem warning notice for Australia

Modems connected to the Australian telecoms network must have a valid Austel

permit. This modem has been designed to specifically configure to ensure compli-

ance with Austel standards when the country/region selection is set to Australia.

The use of other country/region setting while the modem is attached to the

Australian PSTN would result in you modem being operated in a non-compliant

manner. To verify that the country/region is correctly set, enter the command ATI

which displays the currently active setting.

To set the country/region permanently to Australia, enter the following command

sequence:

AT%TE=1

ATS133=1

AT&F

AT&W

AT%TE=0

ATZ

Failure to set the modem to the Australia country/region setting as shown above

will result in the modem being operated in a non-compliant manner. Consequently,

there would be no permit in force for this equipment and the Telecoms Act 1991

prescribes a penalty of $12,000 for the connection of non-permitted equipment.

Notes for use of this device in New Zealand

❑The grant of a Telepermit for a device in no way indicates Telecom acceptance

of responsibility for the correct operation of that device under all operating

conditions. In particular the higher speeds at which this modem is capable of

operating depend on a specific network implementation which is only one of

many ways of delivering high quality voice telephony to customers. Failure to

operate should not be reported as a fault to Telecom.

❑In addition to satisfactory line conditions a modem can only work properly if:

a/ it is compatible with the modem at the other end of the call and

b/ the application using the modem is compatible with the application at the

other end of the call - e.g., accessing the Internet requires suitable

software in addition to a modem.

❑This equipment shall not be used in any manner which could constitute a

nuisance to other Telecom customers.

❑Some parameters required for compliance with Telecom’s PTC Specifications

are dependent on the equipment (PC) associated with this modem. The

associated equipment shall be set to operate within the following limits for

compliance with Telecom Specifications:

a/ There shall be no more than 10 call attempts to the same number within

any 30 minute period for any single manual call initiation, and

b/ The equipment shall go on-hook for a period of not less than 30 seconds

between the end of one attempt and the beginning of the next.

c/ Automatic calls to different numbers shall be not less than 5 seconds

apart.

❑Immediately disconnect this equipment should it become physically damaged,

and arrange for its disposal or repair.

❑The correct settings for use with this modem in New Zealand are as follows:

ATB0 (CCITT operation)

AT&G2 (1800 Hz guard tone)

AT&P1 (Decadic dialing make-break ratio =33%/67%)

ATS0=0 (not auto answer)

ATS6=4 (Blind dial deplay)

ATS7=less than 90 (Time to wait to carrier after dialing)

ATS10=less than 150 (loss of carrier to hang up delay, factory default of 15

recommended)

ATS11=90 (DTMF dialing on/off duration=90 ms)

ATX2 (Dial tone detect, but not (U.S.A.) call progress detect)

❑When used in the Auto Answer mode, the S0 register must be set with a value

of 3 or 4. This ensures:

(a) a person calling your modem will hear a short burst of ringing before the

modem answers. This confirms that the call has been successfully

switched through the network.

(b) caller identification information (which occurs between the first and

second ring cadences) is not destroyed.

❑The preferred method of dialing is to use DTMF tones (ATDT...) as this is

faster and more reliable than pulse (decadic) dialing. If for some reason you

must use decadic dialing, your communications program must be set up to

record numbers using the following translation table as this modem does not

implement the New Zealand “Reverse Dialing” standard.

Number to be dialed: 0 1 2 3 4 5 6 7 8 9

Number to program into computer: 0 9 8 7 6 5 4 3 2 1

Note that where DTMF dialing is used, the numbers should be entered

normally.

❑The transmit level from this device is set at a fixed level and because of this

there may be circumstances where the performance is less than optimal. Before

reporting such occurrences as faults, please check the line with a standard

Telepermitted telephone, and only report a fault if the phone performance is

impaired.

❑It is recommended that this equipment be disconnected from the Telecom line

during electrical storms.

❑When relocating the equipment, always disconnect the Telecom line connec-

tion before the power connection, and reconnect the power first.

❑This equipment may not be compatible with Telecom Distinctive Alert ca-

dences and services such as Fax Ability.

NOTE THAT FAULT CALLOUTS CAUSED BY ANY OF THE ABOVE

CAUSES MAY INCUR A CHARGE FROM TELECOM

General conditions

As required by PTC 100, please ensure that this office is advised of any changes to

the specifications of these products which might affect compliance with the relevant

PTC Specifications.

The grant of this Telepermit is specific to the above products with the marketing

description as stated on the Telepermit label artwork. The Telepermit may not be

assigned to other parties or other products without Telecom approval.

A Telepermit artwork for each device is included from which you may prepare any

number of Telepermit labels subject to the general instructions on format, size and

colour on the attached sheet.

The Telepermit label must be displayed on the product at all times as proof to

purchasers and service personnel that the product is able to be legitimately

connected to the Telecom network.

The Telepermit label may also be shown on the packaging of the product and in the

sales literature, as required in PTC 100.

The charge for a Telepermit assessment is $337.50. An additional charge of $337.50

is payable where an assessment is based on reports against non-Telecom New

Zealand Specifications. $112.50 is charged for each variation when submitted at the

same time as the original.

An invoice for $NZ1237.50 will be sent under separate cover.

xiii

Table of Contents

Preface

Manual contents .................................................................................xix

Conventions .........................................................................................xx

Abbreviations ........................................................................................ xx

Icons .................................................................................................... xx

Keys .................................................................................................... xx

Key operation ...................................................................................... xxi

Display ................................................................................................ xxi

Messages ........................................................................................... xxi

General Precautions

Stress injury ..................................................................................... xxiii

Heat injury .........................................................................................xxiii

Pressure or impact damage...............................................................xxiii

PC card overheating .......................................................................... xxiv

Mobile phone ..................................................................................... xxiv

Central Processing Unit ("CPU") Performance Disclaimer .................. xxiv

Cooling fan .........................................................................................xxv

Chapter 1 Introduction

Equipment checklist .......................................................................... 1-1

Hardware ............................................................................................ 1-1

Software ............................................................................................. 1-1

Features ............................................................................................. 1-2

Special features................................................................................. 1-7

Utilities................................................................................................ 1-9

Options ............................................................................................. 1-11

Chapter 2 The Grand Tour

Front with the display closed ........................................................... 2-1

Left side.............................................................................................. 2-2

Right side ........................................................................................... 2-3

Back side ............................................................................................ 2-4

Underside ........................................................................................... 2-5

xiv

Front with the display open .............................................................. 2-7

Indicators............................................................................................ 2-9

AC adaptor ....................................................................................... 2-12

Chapter 3 Getting Started

Setting up your work space .............................................................. 3-2

General conditions .............................................................................. 3-2

Placement of computer....................................................................... 3-3

Seating and posture ........................................................................... 3-3

Lighting .............................................................................................. 3-4

Work habits ........................................................................................ 3-4

Operating the computer in tablet mode .......................................... 3-5

Connecting the AC adaptor .............................................................. 3-6

Opening the display .......................................................................... 3-8

Turning on the power ....................................................................... 3-9

Starting up for the first time............................................................ 3-10

Turning off the power ..................................................................... 3-10

Shut Down mode (Boot mode) .......................................................... 3-10

Hibernation mode ............................................................................. 3-11

Standby mode .................................................................................. 3-13

Restarting the computer ................................................................. 3-15

Restoring the preinstalled software from

the Product Recovery CD-ROM....................................................... 3-15

Chapter 4 Operating Basics

Using the Touch Pad ......................................................................... 4-1

Using the Tablet PC Pen and Reserve Pen ..................................... 4-2

Inserting the Tablet PC Pen ................................................................ 4-4

Removing the Tablet PC Pen .............................................................. 4-5

Pen actions ........................................................................................ 4-5

Single tap ........................................................................................... 4-5

Double tap .......................................................................................... 4-5

Press and hold ................................................................................... 4-5

Drag ................................................................................................... 4-6

Drag and drop ..................................................................................... 4-6

Replacing the pen tip .......................................................................... 4-6

Inserting the Reserve Pen ................................................................... 4-7

Removing the Reserve Pen ................................................................. 4-7

Changing to the Tablet mode........................................................... 4-8

Changing the screen orientation ................................................... 4-10

Method 1: Changing the screen orientation

using TOSHIBA Accelerometer Utilities ............................................ 4-11

Method 2: Changing the screen orientation

using Enter/Menu Button .................................................................. 4-12

Method 3: Changing the screen orientation

using Task Bar ................................................................................. 4-12

Changing to the laptop mode......................................................... 4-13

Using the USB FDD Kit .................................................................... 4-13

Connecting the USB diskette drive ................................................... 4-14

Disconnecting the USB diskette drive ............................................... 4-15

Diskette care .................................................................................... 4-15

Wireless communications ............................................................... 4-16

Wireless LAN ................................................................................... 4-16

Bluetooth wireless technology .......................................................... 4-17

Wireless communication switch ....................................................... 4-18

Wireless communication Indicator .................................................... 4-18

LAN ................................................................................................... 4-19

LAN cable types ............................................................................... 4-19

Connecting LAN cable ...................................................................... 4-19

Disconnecting LAN cable ................................................................. 4-20

Using the microphones ................................................................... 4-21

Audio ................................................................................................ 4-21

Using the internal modem .............................................................. 4-24

Region selection ............................................................................... 4-25

Properties menu ............................................................................... 4-25

Connecting ....................................................................................... 4-26

Disconnecting................................................................................... 4-27

Cleaning the computer ................................................................... 4-27

Moving the computer ...................................................................... 4-28

Heat dispersal .................................................................................. 4-28

Chapter 5 The Keyboard

Typewriter keys ................................................................................. 5-1

F1 … F12 function keys ..................................................................... 5-2

Soft keys: Fn key combinations........................................................ 5-2

Emulating keys on enhanced keyboard .............................................. 5-2

Hotkeys.............................................................................................. 5-4

Fn Sticky key ..................................................................................... 5-7

Windows special keys ....................................................................... 5-7

Keypad overlay.................................................................................. 5-7

Turning on the overlays ....................................................................... 5-7

xvi

Temporarily using normal keyboard (overlay on).................................. 5-8

Temporarily using overlay (overlay off) ................................................. 5-9

Temporarily changing modes .............................................................. 5-9

Generating ASCII characters ............................................................ 5-9

Chapter 6 Power and Power-Up Modes

Power conditions............................................................................... 6-1

Power indicators ............................................................................... 6-3

Battery indicators ............................................................................... 6-3

DC IN 15V indicator ............................................................................ 6-3

Power indicator ................................................................................... 6-4

Battery types ...................................................................................... 6-4

Battery Pack ...................................................................................... 6-4

Real time clock battery....................................................................... 6-5

Care and use of the Battery Pack .................................................... 6-5

Safety precautions .............................................................................. 6-6

Charging the batteries ........................................................................ 6-9

Monitoring battery capacity .............................................................. 6-10

Maximizing battery operating time .................................................... 6-11

Retaining data with power off ............................................................ 6-12

Extending battery life ........................................................................ 6-12

Replacing the Battery Pack ............................................................ 6-13

Removing the Battery Pack .............................................................. 6-13

Installing the Battery Pack................................................................ 6-15

TOSHIBA Password Utility .............................................................. 6-16

User password ................................................................................. 6-16

Supervisor password ......................................................................... 6-17

Starting the computer by password .................................................. 6-18

Tablet mode..................................................................................... 6-18

Power-up modes ............................................................................. 6-19

Windows utilities .............................................................................. 6-19

Hotkeys............................................................................................ 6-19

Panel power off ............................................................................... 6-19

System Auto Off ............................................................................... 6-20

Chapter 7 HW Setup

HW Setup ........................................................................................... 7-1

Accessing HW Setup ......................................................................... 7-1

HW Setup window .............................................................................. 7-1

xvii

Chapter 8 Optional Devices

PC cards ............................................................................................. 8-2

Inserting a PC card ............................................................................. 8-2

Removing a PC card ........................................................................... 8-3

SD cards ............................................................................................. 8-3

Inserting an SD card ........................................................................... 8-4

Removing an SD card ......................................................................... 8-4

Memory expansion ............................................................................ 8-6

Installing memory module ................................................................... 8-7

Removing memory module .................................................................. 8-9

Battery Pack..................................................................................... 8-10

Universal AC Adaptor ...................................................................... 8-10

Battery Charger ............................................................................... 8-11

USB diskette Kit ............................................................................... 8-11

Tablet Multi Dock............................................................................. 8-11

External monitor .............................................................................. 8-12

Tablet PC Pen set ............................................................................ 8-12

Reserve pen ..................................................................................... 8-12

Security lock .................................................................................... 8-13

Chapter 9 Troubleshooting

Problem solving process ................................................................... 9-1

Preliminary checklist .......................................................................... 9-1

Analyzing the problem ........................................................................ 9-2

Hardware and system checklist........................................................ 9-3

System start-up.................................................................................. 9-3

Self test.............................................................................................. 9-4

Power ................................................................................................. 9-4

Password ........................................................................................... 9-7

Keyboard ............................................................................................ 9-8

LCD panel .......................................................................................... 9-8

Hard disk drive .................................................................................... 9-9

Diskette drive ...................................................................................... 9-9

Infrared port ...................................................................................... 9-10

Pointing device ................................................................................. 9-10

PC card ............................................................................................ 9-13

SD card ............................................................................................ 9-14

Monitor ............................................................................................. 9-14

Sound system .................................................................................. 9-15

USB ................................................................................................. 9-15

Memory expansion ........................................................................... 9-16

xviii

Standby/Hibernation ......................................................................... 9-17

Modem ............................................................................................. 9-17

LAN .................................................................................................. 9-19

Wireless LAN ................................................................................... 9-19

Bluetooth .......................................................................................... 9-20

Real Time Clock ............................................................................... 9-20

TOSHIBA support ............................................................................. 9-21

Before you call ................................................................................. 9-21

Where to write .................................................................................. 9-21

Appendixes

Appendix A

Specifications .....................................................................................A-1

Appendix B

Display Controller and Modes ...........................................................B-1

Appendix C

AT Commands ....................................................................................C-1

Appendix D

S-registers ...........................................................................................D-1

Appendix E

V.90 ...................................................................................................... E-1

Appendix F

Wireless LAN....................................................................................... F-1

Appendix G

AC Power Cord and Connectors....................................................... G-1

Appendix H

Internal Modem Guide .......................................................................H-1

Appendix I

Parts Numbers ..................................................................................... I-1

Glossary

Index

xix

Preface

Congratulations on your purchase of the TOSHIBA Portégé M200 computer. This

powerful, lightweight notebook computer is designed to provide years of reliable,

high-performance computing.

This manual tells how to set up and begin using your TOSHIBA Portégé M200

computer. It also provides detailed information on configuring your computer, basic

operations and care, using optional devices and troubleshooting.

If you are a new user of computers or if you’re new to portable computing, first read

over the Introduction and The Grand Tour chapters to familiarize yourself with the

computer’s features, components and accessory devices. Then read Getting Started

for step-by-step instructions on setting up your computer.

If you are an experienced computer user, please continue reading the preface to

learn how this manual is organized, then become acquainted with this manual by

browsing through its pages. Be sure to look over the Special features section of the

Introduction, to learn about features that are uncommon or unique to the computers

and carefully read HW Setup. If you are going to install PC cards or connect external

devices such as a monitor, be sure to read Chapter 8, Optional Devices.

Manual contents

This manual is composed of nine chapters, nine appendixes, a glossary, and an

index.

Chapter 1, Introduction, is an overview of the computer’s features, capabilities, and

options.

Chapter 2, The Grand Tour, identifies the components of the computer and briefly

explains how they function.

Chapter 3, Getting Started, provides a quick overview of how to begin operating

your computer in laptop mode and tablet mode and gives tips on safety and

designing your work area.

Chapter 4, Operating Basics, includes tips on care of the computer and on using the

Touch Pad ,Tablet PC Pen, external diskette drive, Wireless LAN, Bluetooth, LAN,

microphone and internal modem.

User's Manual

Chapter 5, The Keyboard, describes special keyboard functions including the

keypad overlay and hotkeys.

Chapter 6, Power and Power-Up Modes, gives details on the computer’s power

resources and battery save modes and how to set a password.

Chapter 7, HW Setup, explains how to configure the computer using the HW Setup

program.

Chapter 8, Optional Devices, describes the optional hardware available.

Chapter 9, Troubleshooting, provides helpful information on how to perform some

diagnostic tests, and suggests courses of action if the computer doesn’t seem to be

working properly.

The Appendixes provide technical information about your computer.

The Glossary defines general computer terminology and includes a list of acronyms

used in the text.

The Index quickly directs you to the information contained in this manual.

Conventions

This manual uses the following formats to describe, identify, and highlight terms

and operating procedures.

Abbreviations

On first appearance, and whenever necessary for clarity, abbreviations are enclosed

in parentheses following their definition. For example: Read Only Memory

(ROM). Acronyms are also defined in the Glossary.

Icons

Icons identify ports, dials, and other parts of your computer. The indicator panel

also uses icons to identify the components it is providing information on.

Keys

The keyboard keys are used in the text to describe many computer operations. A

distinctive typeface identifies the key top symbols as they appear on the keyboard.

For example, Enter identifies the Enter key.

xxi

Key operation

Some operations require you to simultaneously use two or more keys. We identify

such operations by the key top symbols separated by a plus sign (+). For example,

Ctrl + C means you must hold down Ctrl and at the same time press C. If three

keys are used, hold down the first two and at the same time press the third.

ABC When procedures require an action such as clicking an icon or entering

text, the icon’s name or the text you are to type in is represented in the

type face you see to the left.

Display

ABC Names of Windows® or icons or text generated by the computer that

appears on its display screen is presented in the type face you see to the

left.

Messages

Messages are used in this manual to bring important information to your attention.

Each type of message is identified as shown below.

CAUTION: Pay attention! A caution informs you that improper use of

equipment or failure to follow instructions may cause data loss or

damage your equipment.

NOTE: Please read. A note is a hint or advice that helps you make best

use of your equipment.

Conventions

xxii

User's Manual

xxiii

General Precautions

TOSHIBA computers are designed to optimize safety, minimize strain and withstand

the rigors of portability. However, certain precautions should be observed to further

reduce the risk of personal injury or damage to the computer.

Be certain to read the general precautions below and to note the cautions included

in the text of the manual.

Stress injury

Carefully read the Instruction Manual for Safety & Comfort. It contains information

on prevention of stress injuries to your hands and wrists than can be caused by

extensive keyboard use. Chapter 3, Getting Started, also includes information on

workspace design, posture and lighting that can help reduce physical stress.

Heat injury

❑Avoid prolonged physical contact with the computer. If the computer is used

for long periods, its surface can become very warm. While the temperature will

not feel hot to the touch, if you maintain physical contact with the computer for

a long time (if you rest the computer on your lap, or if you keep your hands on

the palm rest, for example) your skin might suffer low-heat injury.

❑If the computer has been used for a long time, avoid direct contact with the

metal plate supporting the I/O ports. It can become hot.

❑The surface of the AC adaptor can become hot when in use. This condition

does not indicate a malfunction. If you need to transport the AC adaptor,

disconnect it and let it cool before moving it.

❑Do not lay the AC adaptor on a material that is sensitive to heat. The material

could be damaged.

Pressure or impact damage

Do not apply heavy pressure to the computer or subject it to strong impact.

Excessive pressure or impact can cause damage to computer components or

otherwise cause malfunctions.

User's Manual

xxiv

PC card overheating

Some PC cards can become hot with prolonged use. Overheating of a PC card can

result in errors or instability in the PC card operation. Also be careful when you

remove a PC card that has been used for a long time.

Mobile phone

Use of mobile phones can interfere with the audio system. Computer operation is

not impaired but is recommended that a distance of 30 cm be maintained between

the computer and a mobile phone in use.

Central Processing Unit ("CPU") Performance

Disclaimer

CPU Performance in your computer product may vary from specifications under the

following conditions:

1. use of certain peripheral products

2. use of battery power instead of AC power

3. use of certain multimedia games or videos with special effects

4. use of standard telephone lines or low speed network connections

5. use of complex modeling software, such as high end computer aided design

application

6. use of computer in areas with low air pressure (high altitude >1,000 meters or

>3,280 feet above sea level)

7. use of computer at temperatures outside the range of 5°C to 35°C (41°F to

95°F) or >25°C (77°F) at high altitude (all temperature reference are

approximate).

CPU Performance may also vary from specifications due to design configuration.

Under some conditions, your computer product may automatically shut-down. This

is a normal protective feature designed to reduce the risk of lost data or damage to

the product when used outside recommended conditions. To avoid risk of lost data,

always make back-up copies of data by periodically storing it on an external storage

medium. For optimum performance, use your computer product only under

recommended conditions Read additional restrictions under “Environmental

Conditions” in your product Resource Guide. Contact TOSHIBA Service and

Support for more information.

xxv

Cooling fan

This product is equipped with a CPU cooling fan, VGA cooling fan and vent holes.

Please make sure to follow the cautions below to avoid overheat.

❑Clean any dust or dirt that has accumulated on the CPU cooling fan, VGA

cooling fan or vent holes.

❑Do not block the CPU cooling fan, VGA cooling fan or vent holes.

❑Use, place and carry the computer in the recommended manner.

NOTE: Do not block the vents during use. Cooling fans draw in outside air.

CPU cooling fan, VGA cooling fan and vents

Stress injury

CPU COOLING FAN VENT

VGA COOLING FAN VENT

User's Manual

xxvi

NTRODUCTION

Chapter 1

Introduction

Equipment checklist .......................................................................... 1-1

Hardware ............................................................................................ 1-1

Software ............................................................................................. 1-1

Features ............................................................................................. 1-2

Special features................................................................................. 1-7

Utilities................................................................................................ 1-9

Options ............................................................................................. 1-11

INTRODUCTION

1-1

NTRODUCTION

Chapter 1

Introduction

This chapter provides an equipment checklist, and it identifies the computer’s

features, options and accessories.

CAUTION: Some of the features described in this manual may not

function properly if you use an operating system that was not prein-

stalled by TOSHIBA.

Equipment checklist

Hardware

Carefully unpack your computer. Save the box and packing materials for future use.

Check to make sure you have all the following items:

❑Portégé M200 Portable Personal Computer

❑Universal AC adaptor and power cord

❑Modular cable

❑Tablet PC Pen

NOTE: Tablet PC Pen is included in the carton of pen set with the

product when purchased. Spare pen tip and draw-out tool are also

included in the carton.

Software

❑The following software is preinstalled:

•Microsoft® Windows XP Tablet PC Edition

• TOSHIBA Modem driver

• TOSHIBA Display driver

• TOSHIBA Touch Pad driver

• TOSHIBA Sound driver

1-2

User's Manual

INTRODUCTION

• TOSHIBA Bluetooth drivers (Can be used only in Bluetooth models)

• TOSHIBA Wireless LAN Driver

• TOSHIBA Mobile Extension3

• TOSHIBA Utilities

• TOSHIBA Hotkey Utility for Display Devices

• TOSHIBA Tablet Access code Logon Utility

• TOSHIBA Zooming Utility

• TOSHIBA Rotation Utility

• TOSHIBA Accelerometer Utilities

•TOSHIBA Power Saver

•TOSHIBA Common Modules

• TOSHIBA Console

• TOSHIBA Config Free

• TOSHIBA SD Memory Boot Utility

• TOSHIBA Skins for Windows Media Player

• SD card Driver Set

•PC Diagnosis Tool

•Online manual

•Sensiva Symbol Commander

❑Documentation:

•Portégé M200 Portable Personal Computer User’s Manual

•Microsoft Windows XP Tablet PC Edition manual package

•Instruction Manual for Safety & Comfort

•End User License Agreement

•International Limited Warranty (ILW) Instruction

(This instruction is included only with computers sold in ILW supported

areas.)

❑Product Recovery CD-ROM (contains TOSHIBA Management Console, which

is not preinstalled)

Features

The computer uses TOSHIBA’s advanced Large Scale Integration (LSI),

Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to

provide compact size, minimum weight, low power usage, and high reliability. This

computer incorporates the following features and benefits:

1-3

NTRODUCTION

Processor

Built-in The computer is equipped with an Intel®, which

incorporates a math co-processor, a 32 KB level 1 cache

memory and a 1MB level 2 cache memory. It also supports

Enhanced Intel® SpeedStep™ technology.

Intel® Pentium® M processor 1.4 GHz

Intel® Pentium® M processor 1.5 GHz

Intel® Pentium® M processor 1.6 GHz

Intel® Pentium® M processor 1.7 GHz

NOTE: Some models of the computers carry Intel® Centrino™

technology, which is based on three separate technologies of

Intel® Pentium® M, Intel® PRO/Wireless Network Connection, and

Intel® 855 Chipset Family.

Memory

Slot The slot accepts a 128, 256, 512 or 1,024 MB memory

module can be installed in the two memory slots for a

maximum of 2GB system memory.

Level 2 cache 1 MB level 2 cache is provided to maximize performance.

Video RAM 32MB of RAM is provided for Video display

Disks

Built-in Hard disk

• 40 billion bytes (37.26 GB)

• 60 billion bytes (55.87 GB)

• 80 billion bytes (74.53 GB)

Display

The computer’s LCD panel supports high-resolution video graphics. The screen

can be set at a wide range of viewing angles for maximum comfort and readability.

Built-in 12.1" SXGA+-TFT, 1400 horizontal × 1050 vertical pixels,

up to 16 M colors

Graphics controller Graphics controller maximizes display performance. Refer

to Appendix B for more information.

Features

1-4

User's Manual

INTRODUCTION

Keyboard

Built-in 84 keys or 85 keys, compatible with IBM ® enhanced

keyboard, embedded numeric overlay, dedicated cursor

control, and keys. See Chapter5, The Keyboard,

for details.

Touch pad

Built-in A touch pad and control buttons in the palm rest enable

control of the on-screen pointer and scrolling of windows.

Tablet PC Pen

Supplied A pen enables data entry directly through the display

screen.

Reserve pen A pen enables data entry directly through the display

screen. Supplied pen uses a pen instead of Supplied pen

at the time of loss or breakage.

Power

Battery pack The computer is powered by one rechargeable lithium-ion

battery pack.

RTC battery The internal RTC battery backs up the Real Time Clock

(RTC) and calendar.

AC adaptor The universal AC adaptor provides power to the system

and recharges the batteries when they are low. It comes

with a detachable power cord. Because it is universal, it

can receive a range of AC voltage between 100 and 240

volts.

Ports

Headphone Enables connection of a stereo headphone

Microphone Enables connection of a monaural microphone

Infrared The serial infrared port is compatible with Infrared Data

Association (IrDA 1.1) standards. It enables cableless 4

Mbps, 1.152 Mbps, 115.2 kbps, 57.6 kbps, 38.4 kbps, 19.2

kbps or 9.6 kbps data transfer with IrDA 1.1 compatible

external devices.

1-5

NTRODUCTION

External monitor 15-pin, analog VGA port supports VESA DDC2B compat-

ible functions.

Docking Special port for connecting an Tablet Multi Dock.

Universal Serial Bus The computer has two Universal Serial Bus ports that

(USB 2.0) comply with the USB 2.0 standard, which enables data

transfer speeds 40 times faster than the USB 1.1 standard.

(The ports also support USB 1.1.)

Slots

PC card A PC card slot accommodates one 5mm Type II card.

SD card This slot lets you easily transfer data from devices, such

as digital cameras and Personal Digital Assistants, that use

SD card flash-memory.

You can use memory module in this slot.

Multimedia

Sound System Windows Sound System compatible sound system

provides internal speaker as well as jacks for an external

microphone and headphone.

Communications

Modem An internal modem provides capability for data and fax

communication. It supports V.90 (V.92). Refer to Appendix

E. The speed of data transfer and fax depends on analog

telephone line conditions. It has a modem jack for connect-

ing to a telephone line. It is preinstalled as a standard

device in some markets. Both of V.90 and V.92 are

supported only in USA, Canada and Australia. Only V.90

is available in other regions.

LAN The computer is equipped with a LAN card that supports

Ethernet LAN (10 Mbit/s, 10BASE-T) and Fast Ethernet

LAN (100 Mbit/s, 100BASE-TX). It is preinstalled as a

standard device in some markets.

Features

1-6

User's Manual

INTRODUCTION

Wireless LAN Some computers in this series are equipped with a wireless

LAN mini-PCI card that is compatible with other LAN

systems based on Direct Sequence Spread Spectrum/

Orthogonal Frequency Division Multiplexing radio

technology that complies with the IEEE802.11 Standard.

The configuration of the built-in Wireless LAN depends

on the model you purchased.(Revision B or G)

Revision G support a data transfer rate up to 54 Mbit/s.

Revision B support a data transfer rate up to 11 Mbit/s.

Turbo Mode support a data transfer rate up to 108 Mbit/s.

Wireless This switch turns the Wireless LAN and Bluetooth

communication switch communication switchfunctions on and off.

Bluetooth Some computers in this series are equipped with Bluetooth

functions. Bluetooth wireless technology eliminates the

need for cables between electronic devices such as

computers and printers. Bluetooth provides fast, reliable,

and secure wireless communication in a small space.

Security

Security lock slot Connects an optional security lock to anchor the computer

to a desk or other large object.

Software

Operating System One of the following operating systems are Windows XP

Tablet PC Edition. Refer to the preinstalled software

section at the front of this chapter.

TOSHIBA Utilities A number of utilities and drivers are preinstalled to make

your computer more convenient to use. Refer to the

Utilities section in this chapter.

Plug and Play When you connect an external device to the computer or

when you install a component, Plug and Play capability

enables the system to recognize the connection and make

the necessary configurations automatically.

1-7

NTRODUCTION

Special features

The following features are either unique to TOSHIBA computers or are advanced

features, which make the computer more convenient to use.

Hot keys Key combinations let you quickly modify the system

configuration directly from the keyboard without running a

system configuration program.

Keypad overlay Gray keys with gray lettering make up the keypad overlay,

which lets you use the keyboard for ten-key operations or

cursor control.

Display automatic This feature automatically cuts off power to the internal

power off display when there is no keyboard input for a time

specified. Power is restored when any key is pressed. You

can specify the time in the Turn off monitor item of the

Power Save Mode window in TOSHIBA Power Saver.

HDD automatic This feature automatically cuts off power to the hard disk

power off drive when it is not accessed for a time specified. Power is

restored when the hard disk is accessed. You can specify

the time in the Turn off hard disks item of the Power Save

Mode window in TOSHIBA Power Saver.

System automatic This feature automatically turns off power to the system

power off when there is no input for a time specified. You can specify

the time in the System standby or System hibernate item of

the System Power Mode window in TOSHIBA Power

Saver.

Battery save mode This feature lets you save battery power. You can specify

the Power Save Mode in the Running on batteries item of

the Power Save Modes window in TOSHIBA Power Saver.

Power on password Two levels of password security are available: supervisor

and user. This feature prevents unauthorized access to

your computer.

Instant security A hot key function blanks the screen and disables the

computer providing quick and easy data security.

Special features

1-8

User's Manual

INTRODUCTION

Advanced Instant This function is a utility (one of the acceleration sensor

Security utilities) with the following functions.

❑It performs from CrossMenu and PC is changed into a

WorkStation lock state.

❑If PC is moved in the state of a WorkStation lock, beep

sound will sound. Cancel a WorkStation lock, in order

to stop beep sound.

❑ If a WorkStation lock is canceled, a program will be

ended automatically.

Panel power on/off This feature turns power to the computer off when the

display panel is closed and turns it back on when the panel

is opened. You can specify the setting in the When I close

the lid item of the System Power Mode window in

TOSHIBA Power Saver.

Auto power on This feature lets you set a time and date for the computer

to turn on automatically. The feature is useful for receiving

remote communications while you are asleep or away. You

can specify the setting in Scheduled Tasks.

Standby If you have to interrupt your work, you can turn off the

power without exiting from your software. Data is main-

tained in the computer’s main memory. When you turn on

the power again, you can continue working right where

you left off.

Hibernation This feature lets you turn off the power without exiting

from your software. The contents of main memory are

saved to the hard disk, when you turn on the power again,

you can continue working right where you left off.

Heat dispersal To protect from overheating, the CPU has an internal

temperature sensor. If the computer’s internal temperature

rises to a certain level, the cooling fan is turned on or the

processing speed is lowered. Use the Fan item of the

Power Save Modes window in TOSHIBA Power Saver.

Maximum Turns on fan first, then if necessary

Performance lowers CPU processing speed.

Performance Uses a combination of fan and

lowering the CPU processing speed.

Battery optimized Lowers the CPU processing speed

first, then if necessary turns on the

fan.

1-9

NTRODUCTION

TOSHIBA When TOSHIBA Accelerometer Utilities is enabled, you

Accelerometer can invoke the Start menu, switch active windows or

Utilities launch predefined applications by shaking the computer

vertically or horizontally, or tilting it.

You can boot TOSHIBA Accelerometer Utilities from the

menu bar as follows.

[Start]-[All Programs]- [TOSHIBA]-[Tablet PC]-[Setting of

TOSHIBA Accelerometer Utilities]

The Setting of TOSHIBA Accelerometer Utilities screen

appears.

Utilities

This section describes preinstalled utilities and tells how to start them. For details

on operations, refer to each utility’s online manual, help files or readme.txt files.

TOSHIBA Power Saver To access this power savings management program, open

the Control Panel, click Performance and Maintenance and

click the TOSHIBA Power Saver icon.

HW Setup This program lets you customize your hardware settings

according to the way you work with your computer and

the peripherals you use. To start the utility, open the

Control Panel, click Printers and Other Hardware and click

the TOSHIBA HW Setup icon.

Fn-esse This Windows program lets you define your own “short-

cut” keys to quickly launch applications and speed your

work in Windows. To start the utility, click the Windows

Start button, point to All Programs, point to TOSHIBA,

point to Utilities and click Fn-esse.

TOSHIBA Password The TOSHIBA Password Utility provides two levels of

Utility password security: User and Supervisor.

Display Driver The display driver enables simultaneous display on the

for Windows internal LCD, and on an external computer monitor. To

enable this function, use the Display Properties dialogue

box.

Symbol Commander This software enables the user to run an application or to

show home page by drawing a simple mark on the display

with the Tablet PC Pen. You can customize the action to

boot the computer and to run the application.

Utilities

1-10

User's Manual

INTRODUCTION

Sound drivers A broad range of audio controls are available through the

ADI sound driver, including Software Synthesize, Mic

Volume, Noise Resudction and Audio Power Management.

Click Control Panel and click SoundMAX icon to change

the Mic Noise Reduction settings and the Power

Management settings.

For other sound settings, use the Windows Device

Manager, Multimedia Panel or Volume Dial.

TOSHIBA This utility lets you make the Fn key sticky, that is, you

Accessibility can press it once, release it, and they press an “F number”

key. The Fn key remains active until another key is

pressed.

TOSHIBA Mobile This utility allows you to dock with or undock from a

Extension3 docker or port replicator, while your system is powered on,

or while in Stand-by or Hibernation. Settings can be

modified from the "TOSHIBA Mobile Extension3" icon in

the TOSHIBA Console.

Hot key utility This utility lets you display or hide a confirmation message

when you press Fn + F3 or Fn + F4.

TOSHIBA Tablet This utility allows you to logon to the system.

Access Code If a password has been set, a dialog box with a prompt

Logon Utility (e.g. Password=) appears when you turn the power on.

If the system is in tablet mode, you can enter a password

by clicking on keys of the soft keyboard with the Tablet

PC Pen.

TOSHIBA Zooming This utility allows you to enlarge or reduce the text size

Utility on the Internet Explorer window and the icon size on

the desktop.

TOSHIBA Console TOSHIBA Console is a graphical user interface that

provides easy access to help and services. It is the default

function launched by the TOSHIBA Console button.

PC Diagnosis TOSHIBA PC Diagnostic Tool displays the basic in

Tool formation on PC, and the test of built-in devices can also

be performed.You can boot TOSHIBA PC Diagnostic Tool

form the menu bar as follows.

[Start]-[All Programs]-[TOSHIBA]-[Utilities]-[PC Diagnos-

tic Tool]

1-11

NTRODUCTION

Bluetooth TOSHIBA This software enables communication between remote

Stack Bluetooth devices. Refer to the Quick Start Guide.

NOTE: Bluetooth cannot be used in models that do not have a Bluetooth

module installed.

TOSHIBAConfigFree TOSHIBA ConfigFree is a suite of utilities to allow easy

control of communication device and network connec-

tions. TOSHIBA ConfigFree also allows you to find

communication problems and create profiles for easy

switching between location and communication networks.

You can boot TOSHIBA ConfigFree from the menu bar as

follows.

[Start] - [All Programs] - [TOSHIBA] - [Netnor king] -

[ConfigFree]

TOSHIBA SD The TOSHIBA SD memory boot utility is a utility which

Memory Boot Utility can create SD memory card to a boot disk. You can boot

TOSHIBA SD Memory Boot Utility from the menu bar as

follows.

[Start] - [All Programs] - [TOSHIBA] - [Utility] - [SD

Memory Boot Utility]

Dragon Drop The setup image for Drag'n Drop CD+DVD is located

CD+DVD in C:\TOSHIBA.Before using it, please execute the "Setup.exe"

for installation.However, you can only use Drag'n Drop

CD+DVD with the following drives:

• The CD/DVD recordable drives which can connect to the

slim select bay of Tablet Multi Dock

• External CD-RW/DVD-ROM Drive (PA3352x)

Options

You can add a number of options to make your computer even more powerful

and convenient to use. The following options are available:

Memory expansion A 128, 256, 512 or 1,024 MB memory module (PC2700 DDR)

can easily be installed in the computer.

Battery Pack An addition Battery Pack can be purchased from your

TOSHIBA dealer. The Battery Pack is identical to the one

that came with your computer. Use it as a spare or replace-

ment.

Options

1-12

User's Manual

INTRODUCTION

Universal AC Adaptor If you use your computer at more than one site, it may be

convenient to purchase an additional Universal AC

Adaptor (PA3282,PA3283) for each site so you will not

have to carry the adaptor with you.

USB FDD Kit A 3 1/2" diskette drive accommodates 1.44-megabyte or

720-kilobyte diskettes. It connects to a USB port. (You

cannot format 720-kilobyte diskettes on Windows XP, but

you can use previously formatted disks.)

Battery Charger The Battery Charger lets you charge extra batteries outside

the computer.

Security locks The slots are available to attach a security cable to the

computer to deter theft.

Tablet Multi The Tablet Multi Dock provides the ports available

Dock on the computer in addition to separate lineout jack,

External monitor port, Universal Serial Bus port × 3, LAN

jack and Slim Select Bay module.

Wireless LAN Kit This option enables Wireless LAN functions in computer

that does not have preinstalled Wireless LAN. It is

installed by dealers only.

Bluetooth Kit This option enables Bluetooth wireless communications in

computer that does not have preinstalled Bluetooth. It is

installed by dealers only.

Tablet PC Pen Tablet PC Pen can be purchased from your TOSHIBA

dealer. Use it as a spare to your computer.

Spare pen tip and draw-out tool are included.

Reserve pen Tablet PC Pen can be purchased from your TOSHIBA

dealer. Supplied pen uses a pen instead of Supplied pen at

the time of loss or breakage. The pen is set inside the

computer, which connects a battery pack.

DVD-ROM Drive DVD-ROM Drive is available as an optional external

optical disk drive. You can buy the drive from TOSHIBA

dealer.

External CD-RW/ External CD-RW/DVD-RW is an optional accessory

DVD-RW compatible with USB 2.0 port on this computer. You can

buy the drive from TOSHIBA dealer.

Bluetooth SD card2 Bluetooth SD card is an optional accessory compatible

with the SD Card slot of this computer. You can buy the

drive from TOSHIBA dealer.

RAND

OUR

Chapter 2

The Grand Tour