Dynabook UPA3489WL Wireless LAN Mini-PCI Express, 802.11a/b/g User Manual Canary UserManual

Toshiba Corporation Wireless LAN Mini-PCI Express, 802.11a/b/g Canary UserManual

TECRA M7 User Manual

User’s ManualTECRA M7
User’s Manual iiTable of ContentsCopyright. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  viDisclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  viTrademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  viFCC information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viiEU Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  viiiVCCI Class B Information  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  viiiModem warning notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  viiiJapan regulations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  ixInstructions for IC CS-03 certified equipment . . . . . . . . . . . . . . . . . . . xiiNotes for Users in Australia and New Zealand . . . . . . . . . . . . . . . . .  xiiiOptical disc drive safety instructions. . . . . . . . . . . . . . . . . . . . . . . . .  xviInternational precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  xxiPrefaceConventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  xxiiiGeneral PrecautionsCreating a computer-friendly environment . . . . . . . . . . . . . . . . . . . . xxvStress injury . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxvHeat injury . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  xxviPressure or impact damage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  xxviPC card overheating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  xxviMobile phones  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  xxviInstruction Manual for Safety & Comfort . . . . . . . . . . . . . . . . . . . . .  xxviChapter 1 Getting StartedEquipment checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1-1Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1-3Operating the computer in Tablet mode. . . . . . . . . . . . . . . . . . . . . . .  1-4Connecting the AC adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1-6Opening the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1-8Turning on the power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1-8Starting up for the first time  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1-9Turning off the power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1-9
User’s Manual iiiTECRA M7Restarting the computer  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1-13Create Optical Recovery Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1-13Restoring the preinstalled software from the Recovery HDD  . . . .  1-14Restoring the preinstalled software from your creating Recovery Media . . . . . . . . . . . . . . . . . . . . . . . . .  1-14Chapter 2 The Grand TourFront with the display closed  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-1Left side. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-3Right side  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-4Back side. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-5Underside  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-7Front with the display open. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-8Operation buttons  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-11System indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-11Keyboard indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-12Optical disc drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-13AC adaptor  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-16Chapter 3 Features, Utilities and OptionsFeatures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-1Special features  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-6Utilities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-8Optional devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-12PC card  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-13Bridge media slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-15Memory expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-22Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-27Universal AC Adaptor  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-28Slice Expansion Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-28Battery Charger  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-29USB FDD Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-29Tablet PC Pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-31Reserve Pen  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-31External monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-31TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-32Displaying movies on a TV or CRT . . . . . . . . . . . . . . . . . . . . . . . . . .  3-33i.LINK (IEEE1394) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-34TOSHIBA Express Port Replicator . . . . . . . . . . . . . . . . . . . . . . . . . .  3-36Bluetooth USB Adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-37Wireless Optical Mouse with Bluetooth Technology  . . . . . . . . . . .  3-37Wireless Stereo Headset with Bluetooth Technology. . . . . . . . . . .  3-37Security lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-37Options  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-38Chapter 4 Operating BasicsUsing the Touch Pad  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-1
User’s Manual ivTECRA M7Using the Tablet PC Pen and Reserve Pen  . . . . . . . . . . . . . . . . . . . .  4-2Changing to the Tablet mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-7Changing the screen orientation. . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-9Using Accelerometer Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-11Changing to the laptop mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-12Using the Fingerprint Sensor  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-12Using optical disc drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-19Writing CDs on DVD-ROM&CD-R/RW drive . . . . . . . . . . . . . . . . . . .  4-23Writing CD/DVDs on DVD Super Multi drive  . . . . . . . . . . . . . . . . . .  4-25Media care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-31Sound System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-32Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-33Wireless communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-36LAN  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-40Cleaning the computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-42Moving the computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-42Using the Hard Disk Drive (HDD) Protection . . . . . . . . . . . . . . . . . .  4-43Heat dispersal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-45Chapter 5 The KeyboardTypewriter keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-1Function keys: F1 … F12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-2Soft keys: Fn key combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-2Hot keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-3Windows special keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-7Keypad overlay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-7Generating ASCII characters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-9Chapter 6 Power and Power-Up ModesPower conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6-1Power indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6-4Battery types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6-5Care and use of the battery pack  . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6-7Replacing the battery pack  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6-11TOSHIBA Password Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6-13Tablet mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6-17Power-up modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6-17Panel power on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6-18System Auto Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6-18Chapter 7 HW Setup & BIOS SetupAccessing HW Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  7-1HW Setup window  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  7-1BIOS Setup Program  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  7-8Chapter 8 TroubleshootingProblem solving process. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  8-1
User’s Manual vTECRA M7Hardware and system checklist  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  8-3TOSHIBA support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  8-22Appendix A SpecificationsPhysical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1Appendix B Display Controller and ModesDisplay controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1Video mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1PowerMizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2Appendix C AT CommandsAppendix D S-registersS-register values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1AT command set result codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-6Appendix E V.90V.90 mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-1AT Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-3Appendix F Wireless LANCard Specifications  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  F-1Radio Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  F-2Supported Frequency Sub-bands. . . . . . . . . . . . . . . . . . . . . . . . . . . .  F-3Appendix G Bluetooth wireless technology InteroperabilityBluetooth wireless technology and your Health . . . . . . . . . . . . . . . . G-3Regulatory statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G-3Using Bluetooth® Card from TOSHIBA equipment in Japan . . . . . . G-5Appendix H AC Power Cord and ConnectorsCertification agencies  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-1Appendix I TOSHIBA Anti-theft Protection TimerAppendix J Legal FootnotesNon-applicable Icons*1  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  J-1CPU*2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  J-1Memory (Main System)*3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  J-2Battery Life*4  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  J-2Hard Disk Drive (HDD) Capacity*5  . . . . . . . . . . . . . . . . . . . . . . . . . . .  J-3LCD*6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  J-3Graphics Processor Unit ("GPU")*7 . . . . . . . . . . . . . . . . . . . . . . . . . .  J-3Wireless LAN*8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  J-3Copy Protection*9  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  J-3Images*10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  J-3GlossaryIndex
User’s Manual viTECRA M7Copyright© 2006 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.TOSHIBA TECRA M7 Portable Personal Computer User’s ManualFirst edition June 2006Copyright authority for music, movies, computer programs, data bases and other intellectual property covered by copyright laws belongs to the author or to the copyright owner. Copyrighted material can be reproduced only for personal use or use within the home. Any other use beyond that stipulated above (including conversion to digital format, alteration, transfer of copied material and distribution on a network) without the permission of the copyright owner is a violation of copyright or author’s rights and is subject to civil damages or criminal action. Please comply with copyright laws in making any reproduction from this manual.DisclaimerThis manual has been validated and reviewed for accuracy. The instructions and descriptions it contains are accurate for the TOSHIBA TECRA M7 Portable Personal Computer at the time of this manual’s production. However, succeeding computers and manuals are subject to change without notice. TOSHIBA assumes no liability for damages incurred directly or indirectly from errors, omissions or discrepancies between the computer and the manual.TrademarksIBM is a registered trademark and IBM PC is a trademark of International Business Machines Corporation.Intel, Intel SpeedStep, Intel Core, Celeron and Centrino are trademarks or registered trademarks of Intel Corporation.Windows and Microsoft are registered trademarks of Microsoft Corporation.Photo CD is a trademark of Eastman Kodak.Sonic RecordNow! is a registered trademark of Sonic Solutions.Bluetooth is a trademark owned by its proprietor and used by TOSHIBA under license.Memory Stick and i.LINK are trademark and registered trademark of Sony Corporation.InterVideo and WinDVD are registered trademarks of InterVideo Inc. Other trademarks and registered trademarks not listed above may be used in this manual.
User’s Manual viiTECRA M7FCC informationProduct Name : TECRA M7Model number : PTM70/PTM71FCC notice "Declaration of Conformity Information"This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:■Reorient or relocate the receiving antenna.■Increase the separation between the equipment and receiver.■Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.■Consult the dealer or an experienced radio/TV technician for help.FCC conditionsThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:1. This device may not cause harmful interference.2. This device must accept any interference received, including interference that may cause undesired operation.ContactAddress: TOSHIBA America Information Systems, Inc.9740 Irvine BoulevardIrvine, California 92618-1697Telephone: (949) 583-3000Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s external monitor port, USB port, IEEE1394 port and microphone jack. Changes or modifications made to this equipment, not expressly approved by TOSHIBA or parties authorized by TOSHIBA could void the user’s authority to operate the equipment.
User’s Manual viiiTECRA M7EU Declaration of ConformityTOSHIBA declares, that the product: PTM70*/PTM71* conforms to the following Standards:This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe Gmblt, Hammfelddamm 8, 41460 Neuss, Germany.VCCI Class B InformationModem warning noticeConformity StatementThe equipment has been approved to [Commission Decision "CTR21"] for pan-European single terminal connection to the Public Switched Telephone Network (PSTN).However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.In the event of problems, you should contact your equipment supplier in the first instance.Supplementary Information: “The product complies with the requirements of the Low Voltage Directive 73/23/EEC, the EMC Directive 89/336/EEC and/or the R&TTE Directive 1999/5/EC.”
User’s Manual ixTECRA M7Network Compatibility StatementThis product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the additional requirements conditional in EG 201 121.Germany ATAAB AN005,AN006,AN007,AN009,AN010 and DE03,04,05,08,09,12,14,17Greece ATAAB AN005,AN006 and GR01,02,03,04Portugal  ATAAB AN001,005,006,007,011 and P03,04,08,10Spain   ATAAB AN005,007,012, and ES01Switzerland ATAAB AN002All other countries/regions ATAAB AN003,004Specific switch settings or software setup are required for each network, please refer to the relevant sections of the user guide for more details.The hookflash (timed break register recall) function is subject to separate national type approvals. It has not been tested for conformity to national type regulations, and no guarantee of successful operation of that specific function on specific national networks can be given.Japan regulationsRegion selectionIf you are using the computer in Japan, technical regulations described in the Telecommunications Business Law require that you select the Japan region mode. It is illegal to use the modem in Japan with any other selection.RedialUp to two redial attempts can be made. If more than two redial attempts are made, the modem will return Black Listed. If you are experiencing problems with the Black Listed code, set the interval between redials at one minute or longer. Japan’s Telecommunications Business Law permits up to two redials on analogue telephones, but the redials must be made within a total of three minutes.The internal modem is approved by Japan Approvals Institute for Telecommunications Equipment.A04-0609001
User’s Manual xTECRA M7One of the labels is located on the module.Pursuant to FCC CFR 47, Part 68:When you are ready to install or use the modem, call your local telephone company and give them the following information:■The telephone number of the line to which you will connect the modem■The registration number that is located on the deviceThe FCC registration number of the modem will be found on either the device which is to be installed, or, if already installed, on the bottom of the computer outside of the main system label.■The Ringer Equivalence Number (REN) of the modem, which can vary. For the REN of your modem, refer to your modem’s label.The modem connects to the telephone line by means of a standard jack called the USOC RJ11C.
User’s Manual xiTECRA M7Type of serviceYour modem is designed to be used on standard-device telephone lines. Connection to telephone company-provided coin service (central office implemented systems) is prohibited. Connection to party lines service is subject to state tariffs. If you have any questions about your telephone line, such as how many pieces of equipment you can connect to it, the telephone company will provide this information upon request.Telephone company proceduresThe goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations, or procedures. If these changes might affect your service or the operation of your equipment, the telephone company will give you notice in writing to allow you to make any changes necessary to maintain uninterrupted service.If problems ariseIf any of your telephone equipment is not operating properly, you should immediately remove it from your telephone line, as it may cause harm to the telephone network. If the telephone company notes a problem, they may temporarily discontinue service. When practical, they will notify you in advance of this disconnection. If advance notice is not feasible, you will be notified as soon as possible. When you are notified, you will be given the opportunity to correct the problem and informed of your right to file a complaint with the FCC. In the event repairs are ever needed on your modem, they should be performed by TOSHIBA Corporation or an authorized representative of TOSHIBA Corporation.DisconnectionIf you should ever decide to permanently disconnect your modem from its present line, please call the telephone company and let them know of this change.Fax brandingThe Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business, other entity or individual sending the message and the telephone number of the sending machine or such business, other entity or individual. In order to program this information into your fax modem, you should complete the setup of your fax software before sending messages.
User’s Manual xiiTECRA M7Instructions for IC CS-03 certified equipment1. The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection.The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe systems, if present, are connected together. This precaution may be particularly important in rural areas.2. The user manual of analog equipment must contain the equipment’s Ringer Equivalence Number (REN) and an explanation notice similar to the following:The Ringer Equivalence Number (REN) of the modem, which can vary. For the REN of your modem, refer to your modem’s label.3. The standard connecting arrangement (telephone jack type) for this equipment is jack type(s): USOC RJ11C.The IC registration number of the modem is shown below.Canada: 4005B-ATHENSUsers should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.
User’s Manual xiiiTECRA M7Notes for Users in Australia and New ZealandModem warning notice for AustraliaModems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compliance with Austel standards when the country/region selection is set to Australia. The use of other country/region setting while the modem is attached to the Australian PSTN would result in you modem being operated in a non-compliant manner. To verify that the country/region is correctly set, enter the command ATI which displays the currently active setting. To set the country/region permanently to Australia, enter the following command sequence:AT%TE=1ATS133=1AT&FAT&WAT%TE=0ATZFailure to set the modem to the Australia country/region setting as shown above will result in the modem being operated in a non-compliant manner. Consequently, there would be no permit in force for this equipment and the Telecoms Act 1991 prescribes a penalty of $12,000 for the connection of non-permitted equipment.Notes for use of this device in New Zealand■The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions. In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers. Failure to operate should not be reported as a fault to Telecom.■In addition to satisfactory line conditions a modem can only work properly if:a/ it is compatible with the modem at the other end of the call and.b/ the application using the modem is compatible with the application at the other end of the call - e.g., accessing the Internet requires suitable software in addition to a modem.■This equipment shall not be used in any manner which could constitute a nuisance to other Telecom customers.
User’s Manual xivTECRA M7■Some parameters required for compliance with Telecom’s PTC Specifications are dependent on the equipment (PC) associated with this modem. The associated equipment shall be set to operate within the following limits for compliance with Telecom Specifications:a/ There shall be no more than 10 call attempts to the same number within any 30 minute period for any single manual call initiation, andb/ The equipment shall go on-hook for a period of not less than 30 seconds between the end of one attempt and the beginning of the next.c/ Automatic calls to different numbers shall be not less than 5 seconds apart.■Immediately disconnect this equipment should it become physically damaged, and arrange for its disposal or repair.■The correct settings for use with this modem in New Zealand are as follows:ATB0 (CCITT operation)AT&G2 (1800 Hz guard tone)AT&P1 (Decadic dialing make-break ratio =33%/67%)ATS0=0 (not auto answer)ATS6=4 (Blind dial delay)ATS7=less than 90 (Time to wait to carrier after dialing)ATS10=less than 150 (loss of carrier to hangup delay, factorydefault of 15 recommended)ATS11=90 (DTMF dialing on/off duration=90 ms)ATX2 (Dial tone detect, but not (U.S.A.) call progress detect)■When used in the Auto Answer mode, the S0 register must be set with a value of 3 or 4. This ensures:■a person calling your modem will hear a short burst of ringing before the modem answers. This confirms that the call has been successfully switched through the network.■caller identification information (which occurs between the first and second ring cadences) is not destroyed.■The preferred method of dialing is to use DTMF tones (ATDT...) as this is faster and more reliable than pulse (decadic) dialing. If for some reason you must use decadic dialing, your communications program must be set up to record numbers using the following translation table as this modem does not implement the New Zealand “Reverse Dialing” standard.Number to be dialed: 0 1 2 3 4 5 6 7 8 9Number to program into computer: 0 9 8 7 6 5 4 3 2 1Note that where DTMF dialing is used, the numbers should be entered normally.
User’s Manual xvTECRA M7■The transmit level from this device is set at a fixed level and because of this there may be circumstances where the performance is less than optimal. Before reporting such occurrences as faults, please check the line with a standard Telepermitted telephone, and only report a fault if the phone performance is impaired.■It is recommended that this equipment be disconnected from the Telecom line during electrical storms.■When relocating the equipment, always disconnect the Telecom line connection before the power connection, and reconnect the power first.■This equipment may not be compatible with Telecom Distinctive Alert cadences and services such as FaxAbility.NOTE THAT FAULT CALLOUTS CAUSED BY ANY OF THE ABOVE CAUSES MAY INCUR A CHARGE FROM TELECOMGeneral conditionsAs required by PTC 100, please ensure that this office is advised of any changes to the specifications of these products which might affect compliance with the relevant PTC Specifications.The grant of this Telepermit is specific to the above products with the marketing description as stated on the Telepermit label artwork. The Telepermit may not be assigned to other parties or other products without Telecom approval.A Telepermit artwork for each device is included from which you may prepare any number of Telepermit labels subject to the general instructions on format, size and color on the attached sheet.The Telepermit label must be displayed on the product at all times as proof to purchasers and service personnel that the product is able to be legitimately connected to the Telecom network.The Telepermit label may also be shown on the packaging of the product and in the sales literature, as required in PTC 100.The charge for a Telepermit assessment is $337.50. An additional charge of $337.50 is payable where an assessment is based on reports against non-Telecom New Zealand Specifications. $112.50 is charged for each variation when submitted at the same time as the original.An invoice for $NZ1237.50 will be sent under separate cover.Following information is only for EU-member states:The use of the symbol indicates that this product may not be treated as household waste. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.
User’s Manual xviTECRA M7Optical disc drive safety instructionsTEACDVD-ROM drive DV-28EBe sure to check the international precautions at the end of this section.■The DVD-ROM drive DV-28E employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.■Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. ■To prevent direct exposure to the laser beam, do not try to open the enclosure.
User’s Manual xviiTECRA M7Panasonic CommunicationsDVD-ROM & CD-R/RW drive UJDA770■The DVD-ROM & CD-R/RW drive UJDA770 employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.■Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. ■To prevent direct exposure to the laser beam, do not try to open the enclosure.
User’s Manual xviiiTECRA M7TEACDVD-ROM & CD-R/RW drive DW-224E■The DVD-ROM & CD-R/RW drive DW-224E employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.■Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. ■To prevent direct exposure to the laser beam, do not try to open the enclosure.
User’s Manual xixTECRA M7Panasonic CommunicationsDVD Super Multi with Double Layer Recording UJ-841■The DVD Super Multi drive with Double Layer Recording model employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.■Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. ■To prevent direct exposure to the laser beam, do not try to open the enclosure.
User’s Manual xxTECRA M7PioneerDVD Super Multi with Double Layer Recording DVR-K16■The DVD Super Multi drive with Double Layer Recording model employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.■Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. ■To prevent direct exposure to the laser beam, do not try to open the enclosure. MFD.SER.NO.CERTIFICATIONTHIS PRODUCT COMPLIES WITH 21 CFR 1040. 10 AND 1040. 11 EXCEPT FOR DEVIATIONS PURSUANT TO LASER NOTICE NO.50.PIONEER CORPORATION. 4-1, MEGURO 1-CHOME, MEGURO-KU, TOKYO, 153-8654, JAPAN
User’s Manual xxiTECRA M7International precautionsCAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure. CLASS 1 LASER PRODUCT LASERSCHUTZKLASSE 1 PRODUKT TOEN60825VORSICHT: Dieses Gerät enthält ein Laser-System und ist als “LASERSCHUTZKLASSE 1 PRODUKT” klassifiziert. Für den richtigen Gebrauch dieses Modells lesen Sie bitte die Bedienungsanleitung sorgfältig durch und bewahren diese bitte als Referenz auf. Falls Probleme mit diesem Modell auftreten, benachrichtigen Sie bitte die nächste “autorisierte Service-Vertretung”. Um einen direkten Kontakt mit dem Laserstrahl zu vermeiden darf das Gerät nicht geöffnet werden. ADVERSEL:USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAF-BRYDER ER UDE AF FUNKTION. UNDGÅ UDSÆTTSLSE FOR STRÅLINGADVARSEL: Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med laserstråler af klasse 1, hviket betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke på apparatets yderside kan bilve udsat for utilladellg kraftig stråling.APPARATET BOR KUN ÅBNES AF FAGFOLK MED SÆRLIGT KENDSKAB TIL APPARATER MED LASERSTRÅLER!Indvendigt i apparatet er anbragt den her gengivne advarselsmækning, som advarer imod at foretage sådanne indgreb i apparatet, at man kan komme til at udsatte sig for laserstråling.
User’s Manual xxiiTECRA M7OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1.VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä.CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.VORSICHT: DIE VERWENDUNG VON ANDEREN STEURUNGEN ODER EINSTELLUNGEN ODER DAS DURCHFÜHREN VON ANDEREN VORGÄNGEN ALS IN DER BEDIENUNGSANLEITUNG BESCHRIEBEN KÖNNEN GEFÄHRLICHE STRAHLENEXPOSITIONEN ZUR FOLGE HABEN.
User’s Manual xxiiiPrefaceCongratulations on your purchase of the TECRA M7 computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing.This manual tells how to set up and begin using your TECRA M7 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting. If you are a new user of computers or if you’re new to portable computing, first read over the Getting Started and Features, Utilities and Optionschapters to familiarize yourself with the computer’s features, components and accessory devices. Then read Getting Started for step-by-step instructions on setting up your computer.If you are an experienced computer user, please continue reading the preface to learn how this manual is organized, then become acquainted with this manual by browsing through its pages. Be sure to look over the Special features section of the Introduction, to learn about features that are uncommon or unique to the computer and carefully read HW Setup & BIOS Setup.If you are going to install PC cards or connect external devices such as a monitor, be sure to read Chapter 3, Features, Utilities and Options.ConventionsThis manual uses the following formats to describe, identify, and highlight terms and operating procedures.AbbreviationsOn first appearance, and whenever necessary for clarity, abbreviations are enclosed in parentheses following their definition. For example: Read Only Memory (ROM). Acronyms are also defined in the Glossary.
User’s Manual xxivTECRA M7IconsIcons identify ports, dials, and other parts of your computer. The indicator panel also uses icons to identify the components it is providing information on.KeysThe keyboard keys are used in the text to describe many computer operations. A distinctive typeface identifies the key top symbols as they appear on the keyboard. For example, Enter identifies the Enter key.Key operationSome operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C. If three keys are used, hold down the first two and at the same time press the third.DisplayMessagesMessages are used in this manual to bring important information to your attention. Each type of message is identified as shown below.ABC When procedures require an action such as clicking an icon or entering text, the icon’s name or the text you are to type in is represented in the type face you see to the left.SABC Names of windows or icons or text generated by the computer that appear on its display screen are presented in the type face you see to the left.Pay attention! A caution informs you that improper use of equipment or failure to follow instructions may cause data loss or damage your equipment.Please read. A note is a hint or advice that helps you make best use of your equipment.Indicates a potentially hazardous situation, which could result in death or serious injury, if you do not follow instructions.
User’s Manual xxvGeneral PrecautionsTOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer.Be certain to read the general precautions below and to note the cautions included in the text of the manual.Creating a computer-friendly environmentPlace the computer on a flat surface that is large enough for the computer and any other items you are using, such as a printer.Leave enough space around the computer and other equipment to provide adequate ventilation. Otherwise, they may overheat.To keep your computer in prime operating condition, protect your work area from:■Dust, moisture, and direct sunlight.■Equipment that generates a strong electromagnetic field, such as stereo speakers(other than speakers that are connected to the computer) or speakerphones.■Rapid changes in temperature or humidity and sources of temperature change such as air conditioner vents or heaters.■Extreme heat, cold, or humidity.■Liquids and corrosive chemicals.Stress injuryCarefully read the Instruction Manual for Safety & Comfort. It contains information on prevention of stress injuries to your hands and wrists than can be caused by extensive keyboard use. Chapter 1, Getting Started, also includes information on work space design, posture and lighting that can help reduce physical stress.
User’s Manual xxviTECRA M7Heat injury■Avoid prolonged physical contact with the computer. If the computer is used for long periods, its surface can become very warm. While the temperature will not feel hot to the touch, if you maintain physical contact with the computer for a long time (if you rest the computer on your lap, or if you keep your hands on the palm rest, for example) your skin might suffer low-heat injury. ■If the computer has been used for a long time, avoid direct contact with the metal plate supporting the I/O ports. It can become hot.■The surface of the AC adaptor can become hot when in use. This condition does not indicate a malfunction. If you need to transport the AC adaptor, disconnect it and let it cool before moving it.■Do not lay the AC adaptor on a material that is sensitive to heat. The material could be damaged.Pressure or impact damageDo not apply heavy pressure to the computer or subject it to strong impact. Excessive pressure or impact can cause damage to computer components or otherwise cause malfunctions.PC card overheatingSome PC cards can become hot with prolonged use. Overheating of a PC card can result in errors or instability in the PC card operation. Also be careful when you remove a PC card that has been used for a long time.Mobile phonesUse of mobile phones can interfere with the audio system. Computer operation is not impaired but it is recommended that a distance of 30 cm be maintained between the computer and a mobile phone in use.Instruction Manual for Safety & ComfortAll important information on the safe and proper use of this computer is described in the enclosed Instruction Manual for Safety & Comfort. Be sure to read it before using the computer.
User’s Manual 1-1Chapter 1Getting StartedThis chapter provides an equipment checklist, and basic information to start using your computer.Equipment checklistCarefully unpack your computer. Save the box and packing materials for future use.HardwareCheck to make sure you have all the following items:■TECRA M7 Portable Personal Computer■AC adaptor and power cord (2-pin plug or 3-pin plug)■USB floppy disk drive (Provided with some models)■Battery pack (It is pre-installed in the computer)■Slice Expansion Battery (Provided with some models)■Tablet PC Pen■Reserve Pen (Provided with some models)Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA.■The Tablet PC Pen is included in the accessory tray of the product when purchased together with spare pen tips and a tip removal tool.■For some models, a Reserve Pen is also included in the accessory tray of the product when purchased.
User’s Manual 1-2Getting StartedDocumentation■TECRA M7 Portable Personal Computer User's Manual■Microsoft Windows XP manual package (Is preinstalled in some regions)■Instruction Manual for Safety & Comfort■End User License AgreementIf any of the items are missing or damaged, contact your dealer immediately.SoftwareMicrosoft® Windows XP Tablet PC Edition■The following software is preinstalled:■Microsoft® Windows XP Tablet PC Edition■Microsoft Internet Explorer■TOSHIBA Utilities■TOSHIBA SD Memory Boot Utility ■DVD Video Player■RecordNow! Basic for TOSHIBA ■DLA for TOSHIBA■Recovery Disc Creator■TOSHIBA TouchPad On/Off Utility■TOSHIBA Power Saver■TOSHIBA Mobile Extension■TOSHIBA Assist■TOSHIBA ConfigFree■TOSHIBA Zooming Utility■TOSHIBA PC Diagnostic Tool■TOSHIBA Controls■TOSHIBA Mic Effect■TOSHIBA Password Utility■TOSHIBA Rotation Utility■TOSHIBA Accelerometer Utilities■TOSHIBA Tablet Access Code Logon Utility■Fingerprint utility■Online manual
User’s Manual 1-3Getting StartedGetting StartedThis section provides basic information to start using your computer. It covers the following topics:■Connecting the AC adaptor■Opening the display■Turning on the power■Starting up for the first time■Turning off the power■Restarting the computer■Creating recovery media■Restoring the preinstalled software from the HDD■All users should be sure to read the section Starting up for the first time.■Be sure to read the enclosed Instruction Manual for Safety & Comfort for information on the safe and proper use of this computer. It is intended to help you be more comfortable and productive while using a notebook computer. By following the recommendations in it you may reduce your chance of developing a painful or disabling injury to your hand, arms, shoulders or neck.■Use a virus-check program and make sure it is updated regularly.■Never format storage media without checking its content. Formatting destroys all stored data.■It is a good idea to periodically back up the internal hard disk or other main storage device to external media. General storage media is not durable or stable over long periods of time and under certain conditions may result in data loss.■Before you install a device or application, save any data in memory to the hard disk drive or other storage media. Failure to do so may result in the loss of data.
User’s Manual 1-4Getting StartedOperating the computer in Tablet modeWhen operating the computer in tablet mode, follow the instructions below.Figure 1-1 Operating the computer in tablet mode■Hold the computer firmly on your forearm. Do not block the vent.■Remove the AC adaptor from the computer when using it in tablet mode held in your forearm.■Do not use the computer while walking or driving a car.■Change to laptop mode and turn off the computer before carrying it. Do not carry the computer with power on or in stand by state. Do not carry the computer while the disk activity LED is glowing.■Do not expose the computer to rapid temperature changes (such as would be the case if you brought the PC from a cold environment into a warm room). When rapid temperature changes are unavoidable, leave the computer for around two hours before turning it on to prevent the formation of condensation.■Remove all external peripheral devices and their connection cables from the computer before carrying. ■Do not drop the computer or apply excessive impact to it. Do not leave the computer in a car or similar environment where it is exposed to direct sunlight.■Do not put the computer in a bag when it is in tablet mode.Change to "The TOSHIBA TECRA M7" computer can be used in two ways, as an ordinary laptop PC and as a Tablet PC. You can use the computer as Tablet PC, operated with the supplied Tablet PC Pen, by turning the LCD display panel through 180 degrees and closing it. This manual calls the use as an ordinary laptop PC "laptop mode", and the use as a Tablet PC "Tablet mode". Refer to Changing to the Tablet mode section in Chapter 4, Operating Basics for details on changing the mode.
User’s Manual 1-5Getting Started■The display panel works as a touch sensitive digitizer screen. However, the outer edges of the screen may be less sensitive. Please keep the Tablet PC Pen inside the display area when you use it near the edges of the display panel. The position of the pen may not be recognized if you move the Tablet PC Pen too fast towards the outer edge. Please be sure to slide the Tablet PC Pen slowly in areas near the edges of the screen.Use the Tablet PC Pen in the areas enclosed by the dotted line as shown in the following figure.Figure 1-2 Use area of a Tablet PC PenDo not block the vent of the computer when holding it. If you continue to expose your skin to the hot air expelled from the vent for a long time, your skin might suffer low temperature injury.
User’s Manual 1-6Getting StartedConnecting the AC adaptorAttach the AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power.The AC adaptor can be connected to any power source supplying from 100 to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to charge the battery pack, refer to Chapter 6, Power and Power-Up Modes.■Always use the TOSHIBA AC adaptor that was provided with your PC and the TOSHIBA Battery Charger (that may have been provided with your PC), or use AC adaptors and battery chargers specified by TOSHIBA to avoid any risk of fire or other damage to the PC. Use of an incompatible AC adaptor or Battery Charger could cause fire or damage to the PC possibly resulting in serious injury. TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor or Battery Charger.■Never plug the AC adaptor or Battery Charger into a power source that does not correspond to both the voltage and the frequency specified on the regulatory label of the unit. Failure to do so could result in a fire or electric shock, possibly resulting in serious injury.■Always use or purchase power cables that comply with the legal voltage and frequency specifications and requirements in the country of use. Failure to do so could result in a fire or electric shock, possibly resulting in serious injury.■The supplied power cord conforms to safety rules and regulations in the region the product is bought and should not be used outside this region. For use in other regions, please buy power cords that conform to safety rules and regulations in the particular region.■Do not use a 3-pin to 2-pin conversion plug.■When you connect the AC adaptor to the computer, always follow the steps in the exact order as described in the User’s Manual. Connecting the power cable to a live electrical outlet should be the last step otherwise the adaptor DC output plug could hold an electrical change and cause an electrical shock or minor bodily injury when touched. As a general safety precaution, avoid touching any metal parts.■Never place your PC or AC adaptor on a wooden surface, furniture, or any other surface that could be marred by exposure to heat since the PC base and AC adaptor's surface increase in temperature during normal use.■Always place your PC or AC adaptor on a flat and hard surface that is resistant to heat damage.Refer to the enclosed Instruction Manual for Safety & Comfort for detailed precautions and handling instructions.
User’s Manual 1-7Getting Started1. Connect the power cord to the AC adaptor.Figure 1-3 Connecting the power cord to the AC adaptor (2-pin plug)Figure 1-4 Connecting the power cord to the AC adaptor (3-pin plug)2. Connect the AC adaptor’s DC output plug to the DC IN 15V jack on the back of the computer.Figure 1-5 Connecting the adaptor to the computer3. Plug the power cord into a live wall outlet. The Battery and DC INindicators on the front of the computer should glow.Depending on the model, a 2-pin plug or 3-pin plug set of the above may be bundled.DC IN 15V jack
User’s Manual 1-8Getting StartedOpening the displayThe computer’s LCD display panel can be opened in a wide range of angles for optimal viewing.1. Push the display latch on the front of the computer to unlatch the display panel.2. While holding down the palm rest with one hand so that the main body is not raised, lift the panel slowly. Adjust the angle of the panel to provide optimal clarity.Figure 1-6 Opening the LCD display panelTurning on the powerThis section describes how to turn on the power.The Power button LED indicates the status. Refer to the Power indicatorssection in Chapter 6, Power and Power-Up Modes.1. Open the computer’s LCD display panel.Use reasonable care when opening and closing the LCD display panel. Opening it vigorously or slamming it shut could damage the computer.Display latchLCD display panel■After you turn on the power for the first time, do not turn it off until you have set up the operating system. Refer to the section Starting up for the first time.■If the USB floppy disk drive is connected, make sure it is empty. If a floppy disk is in the drive, press the eject button and remove the floppy disk.
User’s Manual 1-9Getting Started2. Slide and hold the computer’s power button.Figure 1-7 Turning on the powerStarting up for the first timeWhen you first turn on the power, the computer’s initial screen is the Microsoft Windows XP Startup Screen Logo. Follow the on-screen directions for each screen. During setup, you can click the Back button to return to the previous screen. Turning off the powerThe power can be turned off in one of the following modes: Shut down (Boot), Hibernation or Standby Mode.Shut Down mode (Boot mode)When you turn off the power in Shut Down mode no data is saved and the computer will boot to the operating system’s main screen.1. If you have entered data, save it to the hard disk or to a storage media.2. Make sure all disk (disc) activity has stopped, then remove the CD/DVDs or floppy disk.3. Click start then click Turn Off Computer. From the Turn Off Computer menu select Turn Off.Power buttonBe sure to read the Windows End User License Agreement displaycarefully.■Make sure the hard disk drive indicator is off. If you turn off the power while a disk (disc) is being accessed, you can lose data or damage the disk.■Never turn off the power while an application is running. Doing so could cause loss of data.■Never turn off the power, disconnect an external storage device or remove storage media during data read/write. Doing so can cause data loss.
User’s Manual 1-10Getting Started4. Turn off the power to any peripheral devices.Standby ModeIf you have to interrupt your work, you can turn off the power without exiting from your software. Data is maintained in the computer’s main memory. When you turn on the power again, you can continue working right where you left off. Benefits of standbyThe standby feature provides the following benefits:■Restores the previous working environment more rapidly than does hibernation.■Saves power by shutting down the system when the computer receives no input or hardware access for the duration set by the System Standby feature.■You can use the panel power off feature.Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge.■When the AC adaptor is connected, the computer will go into Standby Mode according to the settings in the TOSHIBA Power Saver. ■To restore operation from Standby Mode, slide the power button or press any key. The latter action only works on the internal keyboard if the Wake-up on Keyboard option is enabled in HW Setup.■If the computer automatically enters Standby Mode while a network application is active, the application might not be restored when the computer wakes up from Standby. ■To prevent the computer from automatically entering Standby Mode, disable Standby in TOSHIBA Power Saver. That action, however, will nullify the computer’s Energy Star compliance.■Before entering Standby Mode, be sure to save your data.■Do not install or remove a memory module while the computer is in Standby Mode. The computer or the module could be damaged.■Do not remove the battery pack while the computer is in Standby Mode (unless the computer is connected to an AC power source). Data in memory will be lost.■If you carry the computer on board an aircraft or into a hospital, be sure to shut down the computer in Hibernation Mode or in shutdown mode to avoid radio signal interference.
User’s Manual 1-11Getting StartedExecuting standbyYou can enter Standby Mode in one of three ways:1. Click start, click Turn Off Computer and click Stand By.2. Close the computer’s LCD display panel. This feature must be enabled. Refer to the Setup Actions tab in TOSHIBA Power Saver located within the Control application (open Performance and Maintenance and then open TOSHIBA Power Saver).3. Slide the power button. This feature must be enabled. Refer to the Setup Actions tab in TOSHIBA Power Saver described in the Control application.Open Performance and Maintenance and open TOSHIBA Power Saver.When you turn the power back on, you can continue where you left when you shut down the computer. Standby limitationsStandby will not function under the following conditions:■Power is turned back on immediately after shutting down.■Memory circuits are exposed to static electricity or electrical noise.Hibernation ModeThe Hibernation Mode feature saves the contents of memory to the hard disk when the computer is turned off. The next time the computer is turned on, the previous state is restored. The Hibernation Mode feature does not save the status of any peripheral devices.You can also enable Standby by pressing Fn + F3. Refer to Chapter 5, The Keyboard, for details.■When the computer is shut down in Standby Mode, the power indicator will blink orange.■If you are operating the computer on battery power, you can lengthen the operating time by shutting down in Hibernation Mode. Standby Mode consumes more power.■Save your data. While entering Hibernation Mode, the computer saves the contents of memory to the hard disk drive. However, for safety sake, it is best to save your data manually.■Data will be lost if you remove the battery or disconnect the AC adaptor before the save is completed. Wait for the HDD indicator to go out.■Do not install or remove a memory module while the computer is in Hibernation Mode. Data will be lost.
User’s Manual 1-12Getting StartedBenefits of Hibernation ModeThe Hibernation Mode feature provides the following benefits:■Saves data to the hard disk when the computer automatically shuts down because of a low battery.■You can return to your previous working environment immediately when you turn on the computer.■Saves power by shutting down the system when the computer receives no input or hardware access for the duration set by the System hibernate feature.■You can use the panel power off feature.Starting Hibernation ModeTo enter Hibernation Mode, follow the steps below.1. Click start.2. Select Turn Off Computer.3. Open the Turn Off Computer dialog box.4. Click Hibernate.Automatic HibernationThe computer will enter Hibernate mode automatically when you slide the power button or close the lid. First, however, make the appropriate settings according to the steps below.1. Click start and open the Control Panel.2. Open Performance and Maintenance and open Power Options.3. Select the Hibernate tab in the Power Options Properties, select the Enable hibernation check box and click the Apply button.4. Open TOSHIBA Power Saver.5. Select the Setup Actions tab.6. Enable the desired Hibernation settings for When I press the power button and When I close the lid.7. Click the OK button.For the computer to shut down in Hibernation Mode, this feature must be enabled in two places: the Hibernate tab in Power Options and Setup Actions tab in TOSHIBA Power Saver.If you do not configure this feature, the computer will shut down in Standby Mode - if battery power becomes depleted, data saved in Standby Mode will be lost.You can also enable Hibernation Mode by pressing Fn + F4. Refer to Chapter 5, The Keyboard, for details.
User’s Manual 1-13Getting StartedData save in Hibernation ModeWhen you turn off the power in Hibernation Mode, the computer takes a moment to save current memory data to the hard disk. During this time, the HDD indicator will light.After you turn off the computer, and the content of memory has been saved to the hard disk, turn off the power to any peripheral devices.Restarting the computerCertain conditions require that you reset the system. For example, if:■You change certain computer settings.■An error occurs and the computer does not respond to your keyboard commands.■There are three ways to reset the computer system:1. Click start then click Turn off computer. From the Turn off computer menu select Restart.2. Press Ctrl + Alt + Del to display the Windows Task Manager, then select Shut Down and Restart.3. Slide the power button and hold it down for five seconds. Wait 10 to 15 seconds, then turn the power on again by sliding the power button.Create Optical Recovery DiscsA recovery image of your computer is stored on the hard disk. You may use this image to create CD or DVD recovery discs using the following steps:1. Select either blank CDs or DVD media.2. The application will allow you to choose a type of media to create recovery CDs/DVD including: CD-R, CD-RW, DVD-R, DVD-RW, DVD+R and DVD+RW.3. Turn on your computer without a PC card storage device such as HDD to open Windows XP.4. Insert the (first) blank media into the tray of the optical disc drive.5. Double click the Recovery Disc Creator Launcher icon on the Windows XP desktop, or Select the application from start Menu.6. After Recovery Disc Creator starts, select the type of media and the title you wish to copy to the media then click the Burn button.Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge.Some media may not be compatible with the optical disc drive of your computer. Please verify your optical disc drive supports the blank media you choose.
User’s Manual 1-14Getting StartedRestoring the preinstalled software from the Recovery HDDAbout 2.5GB of hard disk space is reserved for recovery partition.When re-setting up your hard disk, do not change, delete or add partitions in a manner other than specified in the manual. Otherwise, space for software may be destroyed.In addition, if you use a third-party partitioning program to reconfigure partitions on your hard disk, it may become impossible to re-setup your computer.1. Turn off your computer.2. While holding down 0(zero) key on the keyboard, turn on your computer.3. A menu appears. Follow the on-screen instructions.Restoring the preinstalled software from your creating Recovery MediaIf preinstalled files are damaged, you can either use the Recovery Media you have created or the hard disk drive recovery to restore them. To restore the operating system and all preinstalled software, follow the steps below.1. Load the Recovery Media in the optional optical disc drive and turn off the computer’s power.2. Hold down the F12 key and turn on the power. When In Touch with Tomorrow TOSHIBA appears, release the F12 key.3. Use the left or right cursor key to select the CD-ROM icon in the display menu. For details, refer to the Boot Priority section in Chapter 7, HW Setup & BIOS Setup.4. A menu appears. Follow the on-screen instructions.If your optical disc drive can only write to CDs, select "CD" as the "Type" on Recovery Disc Creator. If your optical disc drive of your computer can write to either CD or DVDs, select the one you are using as the "Type" on Recovery Disc Creator.When sound mute is turned ON by the Fn + Esc key, turn OFF before starting restore. Refer to Chapter 5, The Keyboard, for details.When sound is muted by the Fn + Esc key, turn it on before starting the restore procedure. Refer to Chapter 5, The Keyboard, for details.When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost.
User’s Manual 2-1Chapter 2The Grand TourThis chapter identifies the various components of your computer. Become familiar with each component before you operate the computer.Front with the display closedThe following figure the computer’s front with its LCD display panel in the closed position.Figure 2-1 Front of the computer with LCD display panel closedLegal Footnote (Non-applicable Icons)*1For more information on the Legal Footnote regarding Non-applicable Icons, please refer to the Legal Footnotes section in Appendix J. Click the *1.Display latchSystemindicatorsWireless communication switchVolume controlMicrophone jackHeadphone jackMicrophone
User’s Manual 2-2The Grand TourSystem indicators These LEDs let you monitor the status of various computer functions. Refer to the System indicators section for details.Wireless communication switchSlide this switch to the left to turn off Wireless LAN and Bluetooth functions. Slide it to the right to turn on the functions.All models are provided with a Wireless Communication switch although only some models are equipped with both Wireless LAN and Bluetooth functions.■Turn Wi-Fi® and Bluetooth functionalities off when near a person who may have a cardiac pacemaker implant or other medical electric device. Radio waves may affect pacemaker or medical device operation, possibly resulting in serious injury. Follow the instruction of your medical device when using any Wi-Fi or Bluetooth functionality.■Always turn off Wi-Fi or Bluetooth functionality if the PC is near automatic control equipment or appliances such as automatic doors or fire detectors. Radio waves can cause malfunction of such equipment, possibly resulting in serious injury.■Do not use the Wi-Fi or Bluetooth functionalities near a microwave oven or in areas subject to radio interference or magnetic fields. Interference from a microwave oven or other source can disrupt Wi-Fi or Bluetooth operation.Microphones The built-in microphones let you record sound into your applications. Refer to the Sound System section in Chapter 4, Operating Basics.Microphone jack A 3.5 mm mini microphone jack enables connection of a three-conductor mini jack for monaural microphone input.Headphone jack A 3.5 mm mini headphone jack enables connection of stereo headphones.
User’s Manual 2-3The Grand TourLeft sideThe following figure shows the computer’s left side.Figure 2-2 The left side of the computerVolume control Use this dial to adjust the volume of the stereo speakers and the stereo headphones.Move the Volume control to the right to increase the volume and to the left to decrease the volume.Press the Volume control to Mute the sound. Press the Volume control again to turn Mute off. The mute icon will be displayed when the Volume control is pressed. The same function can be performed by pressing the Fn + Esc keys. Refer to the Hot keys section in Chapter 5 for details on the Fn + Esc keys.Display latch This latch secures the LCD panel in its closed position. Push the latch to open the display.Cooling ventsSecurity lock slot PC card slotPC card eject buttoni.LINK (IEEE1394) portUniversal Serial bus(USB 2.0) port Bridge media slotSecurity lock slot A security cable attaches to this slot. The optional security cable anchors your computer to a desk or other large object to deter theft.Cooling vents Cooling vents help CPU keep from overheating.Do not block the cooling vents. Keep foreign metal objects, such as screws, staples and paper clips, out of the cooling vents. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.Universal Serial Bus (USB 2.0) portThe Universal Serial Bus port is on the left side. The port comply with the USB 2.0 standard.
User’s Manual 2-4The Grand TourRight sideThe following figure shows the computer’s right side.Figure 2-3 The right side of the computerKeep foreign metal objects, such as screws, staples and paper clips, out of the USB connectors. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.Operation of all functions of all USB devices has not been confirmed. Some functions might not execute properly.i.LINK (IEEE1394) portThis port allows you to connect an external device, such as a digital video camera for high-speed data transfer.Bridge media slot This slot lets you insert an SD card, Memory Stick (Pro), xD picture card, MultiMediaCard or SDIO card device. Refer to Chapter 3, Features, Utilities and Options.Keep foreign metal objects, such as screws, staples and paper clips, out of the Bridge Media Slot. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.PC card slot The PC card slot can accommodate a Type II card. The slot supports 16-bit PC cards and CardBus PC cards.PC card eject button This button is used to remove a PC card from the PC card slot.Keep foreign metal objects, such as screws, staples and paper clips, out of the PC Card slot. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.Tablet PC PenOptical disc driveTablet PC Pen slot Universal Serial bus (USB 2.0) port
User’s Manual 2-5The Grand TourBack sideThe following figure shows the computer’s back side.Figure 2-4 The back side of the computerTablet PC Pen slot The Tablet PC Pen slot provides storage for the Tablet PC Pen.Tablet PC Pen The Tablet PC Pen is stored within the right side of the computer and enables direct data entry through the display screen. Refer to the Using the Tablet PC Pen and Reserve Pen section in Chapter 4, Operating Basics.Optical disc drive The computer is configured with a DVD-ROM drive, a DVD-ROM&CD-R/RW drive or a DVD Super Multi drive.Universal Serial Bus (USB 2.0) portThe Universal Serial Bus port is on the right side. Refer to Left side section, for details.DC IN 15V jack External monitor portModem jack LAN jackLAN active indicator (orange) Link indicator (green)Universal Serial bus (USB 2.0) portsS-Video out portDC IN 15V jack The AC adaptor connects to this jack. Use only the model of AC adaptor that comes with the computer. Using the wrong adaptor can damage your computer.Modem jack The modem jack lets you use a modular cable to connect the modem directly to a telephone line.
User’s Manual 2-6The Grand Tour■Connection to any communication line other than an analog phone line could cause a PC system failure.■Connect the built-in modem only to ordinary analog phone lines.■Never connect the built-in modem to a digital line (ISDN).■Never connect the built-in modem to the digital connector on a public telephone or to a digital private branch exchange (PBX).■Never connect the built-in modem to a key telephone system for residences or offices. ■Never operate your PC on AC power during a thunderstorm. If you see lightning or hear thunder, immediately turn off the PC. An electric surge caused by the storm, may result in a system failure, loss of data or hardware damage.S-Video out port Plug an S-Video cable into this jack for S-Video. The S-Video cable carries video signal.Data output depends on the type of device connected to the S-Video cable.LAN jack This jack lets you connect to a LAN. The adaptor has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) and Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T). The LAN has two indicators. Refer to Chapter 4, Operating Basics,for details.■Do not connect any cable other than a LAN cable to the LAN jack. It could cause damage or malfunction.■Do not connect the LAN cable to a power supply. It could cause damage or malfunction.Link indicator (green)This indicator glows green when the computer is connected to a LAN and the LAN is functioning properly.LAN active indicator (orange)This indicator glows orange when data is being exchanged between the computer and the LAN.Universal Serial Bus (USB 2.0) portsTwo Universal Serial Bus ports are on the back side. Refer to Left side section, for details.External monitor portThis external monitor port lets you connect an external video display. Analog VGA port supports VESA DDC2B compatible functions.
User’s Manual 2-7The Grand TourUndersideThe following figure shows the underside of the computer. Make sure the display is closed before turning over your computer.Figure 2-5 The underside of the computerNotchesBattery lockDocking portReserve Pen Battery packBattery release latchCooling ventsNotches Notches on the computer engage hooks on the TOSHIBA Express Port Replicator to ensure a secure connection.Docking port This port enables connection of an optional TOSHIBA Express Port Replicator and a Slice Expansion Battery described in Chapter 3, Features, Utilities and Options.Keep foreign objects out of the docking port. A pin or similar object can damage the computer's circuitry. A plastic shutter protects the connector.Battery pack The battery pack powers the computer when the AC adaptor is not connected. For detailed information on the battery pack, refer to Chapter 6, Power and Power-Up Modes.Battery lock  Slide the battery lock to release the battery pack for removal.Cooling vents The cooling vents is on the underside. Refer to Left side section, for details.
User’s Manual 2-8The Grand TourFront with the display openThis section shows the computer with the LCD display panel open. Refer to the appropriate illustration for details. To open the display, push the display latch on the front of the LCD display panel and lift up. Position the LCD display panel at a comfortable viewing angle.Figure 2-6 The front of the computer with the LCD panel openBattery releaselatchSlide and hold this latch to release the battery pack for removal.For detailed information on removing the battery pack, refer to Chapter 6, Power and Power-Up Modes.Reserve Pen The Reserve Pen is contained in the recess on the underside of the battery pack and enables data entry directly through display screen in addition to the main Tablet PC Pen. Refer to the Using the Tablet PC Pen and Reserve Pensection in Chapter 4, Operating Basics.Display screenTouch Padcontrol buttonsTOSHIBA Presentation buttonTOSHIBA Assist buttonPower buttonLCD Sensor switch(Not shown)ESC/Rotation buttonWindows Security tablet buttonFingerprint SensorCross Function buttonStereospeaker (Left)Stereo speaker (Right)Display hinge Touch PadOperation buttonsKeyboard
User’s Manual 2-9The Grand TourDisplay hinge The display hinge holds the LCD display panel at easy-to-view angles.Display screen The LCD screen displays high-contrast text and graphics. Refer to Display Controller and Modessection in Appendix B.When the computer operates on the AC adaptor the LCD screen’s image will be somewhat brighter than when it operates on battery power. The lower brightness level is intended to save battery power.Stereo speakers The speakers emit sound generated by your software as well as audio alarms, such as low battery condition, generated by the system.Touch Pad A Touch Pad located in the center of the palm rest is used to control the on-screen pointer and scrolling of windows. Refer to the Using the Touch Pad section in Chapter 4, Operating Basics.Touch Pad control buttonsControl buttons below the Touch Pad let you select menu items or manipulate text and graphics designated by the on-screen pointer.Keyboard 84 keys or 85 keys, compatible with IBM®enhanced keyboard, embedded numeric overlay, dedicated cursor control,   and   keys. Refer to Chapter 5, The Keyboard, for details.Power button Slide the power button to turn the computer’s power on and off.Cross Function buttonThis button functions the same as the Enter key when tapped, or shows the menu screen when pressed for more than a second.ESC/Rotation button This button functions the same as the ESC key when tapped, or changes the orientation of the screen when pressed for more than a second.Windows Security tablet buttonThis button functions the same as the Ctrl + Alt + Del keys to show Windows Task Manager.
User’s Manual 2-10The Grand TourTOSHIBA Assist buttonPress this button to launch the TOSHIBA Assist utility (default) or some other predefined application.When the computer is switched off, or is in standby or hibernation mode, press this button to start the computer and launch the assigned application.You can specify the function of the TOSHIBA Assist button in the TOSHIBA Controls properties.TOSHIBA Presentation buttonPress this button to display the same image on both internal and external monitors, or to use multi-monitor display (Windows XP Only).The default setting is "Presentation (Same Image 1024 × 768)" - this means the same image will be displayed on both internal and external monitors with a resolution of 1024 × 768 pixels.When using the "Presentation (Different Image)" setting, you can use the internal and external monitors in wide screen mode (Windows XP only).Pressing this button again changes to single display mode on the internal monitor only.You can specify the function of the TOSHIBA Presentation button in the TOSHIBA Controls properties.Fingerprint SensorThis sensor enables you to enroll and recognize a fingerprint.For detailed information on Fingerprint Sensor, refer to Chapter4, Using the Fingerprint Sensor.LCD Sensor switch This switch senses when the computer’s LCD display panel is closed or opened and activates the Panel Power Off/On feature. When you close the LCD display panel the computer enters Hibernation Mode and shuts down. When you open the computer's LCD display panel the computer starts in Hibernation Mode. Use the TOSHIBA Power Saver to enable or disable this feature. The default is "enabled".Refer to the TOSHIBA Power Saver and Panel Power Off/On items in Chapter 3, Special features, for details on settings.Do not put a magnetic object close to the switch. The computer will automatically enter Hibernation Mode and shut down even if the Panel Power Off feature is disabled.
User’s Manual 2-11The Grand TourOperation buttonsThis section describes the operation buttons.System indicatorsLEDs above icons, light when various computer operations are in progress.Figure 2-7 System indicatorsPlease do not press the buttons too strenuously.Application 1 This button allows you to run applications and access utilities. An application and a function to assign can be configured individually.When the computer is switched off, or is in standby or hibernation mode, press this button to start the computer and launch the assigned application.This button settings can be changed only by administrator.Application 2 This button allows you to run applications and access utilities. An application and a function to assign can be configured individually.When the computer is switched off, or is in standby or hibernation mode, press this button to start the computer and launch the assigned application.This button settings can be changed only by administrator.Bridge Media The Bridge Media indicator glows green when the computer is accessing the Bridge media slot.DC IN The DC IN indicator glows green when DC power is supplied from the AC power adaptor. If the adaptor’s output voltage is abnormal or if the power supply malfunctions, this indicator flashes orange.
User’s Manual 2-12The Grand TourKeyboard indicatorsThe figures below show the positions of the keypad overlay indicators and the Caps Lock indicator.When the Arrow mode indicator glows the keypad overlay lets you control the cursor.When the Numeric mode indicator glows the keypad overlay lets you enter numbers.When the Caps Lock indicator glows the keyboard is in all-caps mode.Figure 2-8 Caps Lock indicatorPower The Power indicator glows green when the computer is on. If you select Stand by from the Turn off computer window, this indicator flashing (one second on, two seconds off) while the computer Standby mode.Battery The Battery indicator shows the condition of the battery’s charge: Green indicates full charge, orange indicates battery charging and flashing orange indicates a low battery charge. Refer toChapter 6, Power and Power-Up Modes.2nd battery The 2nd battery indicator shows the condition of the charge of a Slice Expansion Battery. Green means fully charged and orange means being charged. Refer to Chapter 6, Power and Power-Up Modes.HDD The HDD indicator glows green when the computer is accessing the built-in Hard Disk Drive.Wireless communicationThe Wireless communication indicator glows when the Bluetooth and wireless LAN functions are turned on.All models are provided with a Wireless Communication switch although only some models are equipped with both Wireless LAN and Bluetooth functions.Caps Lock indicatorCaps Lock This indicator glows green when the alphabet keys are locked in uppercase.
User’s Manual 2-13The Grand TourFigure 2-9 Keypad overlay indicatorsOptical disc drivesThe computer is installed with either a DVD-ROM, DVD-ROM&CD-R/RW or a DVD Super Multi drive. An ATAPI interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows.For information on loading and unloading discs refer to the Using optical disc drives section in Chapter 4, Operating Basics.Region codes for DVD drives and mediaDVD-ROM, DVD-ROM&CD-R/RW, DVD Super Multi drives and their associated media are manufactured according to the specifications of six marketing regions. When you purchase DVD-Video, make sure it matches your drive, otherwise it will not play properly.Numeric mode indicatorArrow mode indicatorArrow mode When the Arrow mode indicator lights green, you can use the keypad overlay (gray labeled keys) as cursor keys. Refer to the Keypad overlay section in Chapter 5, The Keyboard.Numeric mode You can use the keypad overlay (gray labeled keys) for numeric input when the Numeric modeindicator lights green. Refer to the Keypad overlay section in Chapter 5, The Keyboard.Code Region1Canada, United States2Japan, Europe, South Africa, Middle East3Southeast Asia, East Asia4Australia, New Zealand, Pacific Islands, Central  America, South America, Caribbean
User’s Manual 2-14The Grand TourWritable discsThis section describes the types of writable CD/DVD discs. Check the specifications of your drive to see the types of discs it can write. Use RecordNow! to write compact discs. Refer to Chapter 3, Features, Utilities and Options.CDs■CD-R discs can be written only once. The recorded data cannot be erased or changed.■CD-RW discs including multi speed CD-RW discs, high-speed CD-RW discs and ultra-speed CD-RW discs can be recorded more than once. DVDs■DVD-R and DVD+R discs can be written only once. The recorded data cannot be erased or changed.■DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than once.FormatsThe drives support the following formats. DVD-ROM drive The drive supports the formats CD-ROM, DVD-ROM, DVD-Video, CD-DA, CD-Text, Photo CDTM (single/multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-EXTRA) and Addressing Method 2.DVD-ROM&CD-R/RW driveThe drive supports the formats in addition to the DVD-ROM drive, and CD-R, CD-RW.DVD Super Multi drive Double LayerThe drive supports the formats in addition to the DVD-ROM&CD-R/RW drive, and DVD-R, DVD-RW, DVD+R, DVD+RW, DVD-RAM, DVD-R DL (Format1), DVD+R DL.5Russia, Indian Subcontinent, Africa, North Korea, Mongolia6ChinaSome types and formats of DVD-R DL and DVD+R DL discs may be unreadable.
User’s Manual 2-15The Grand TourDVD-ROM driveThe full-size DVD-ROM drive module lets you run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor.DVD-ROM&CD-R/RW driveThe full-size DVD-ROM&CD-R/RW drive module lets you record data to rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor.DVD Super Multi drive Double LayerThe full-size DVD Super Multi drive module lets you record data to rewritable CD/DVDs as well as run either 12 cm (4.72") or 8cm (3.15") CD/DVDs without using an adaptor.The read speed is slower at the center of a disc and faster at the outer edge.DVD read 8 speed (maximum)CD read 24 speed (maximum)The read speed is slower at the center of a disc and faster at the outer edge.DVD read 8 speed (maximum)CD read 24 speed (maximum)CD-R write 24 speed (maximum)CD-RW write 24 speed (maximum, Ultra-speed media)The read speed is slower at the center of a disc and faster at the outer edge.DVD read 8 speed (maximum)DVD-R write 8 speed (maximum)DVD-R DL write 2 speed (maximum)DVD-RW write 4 speed (maximum)DVD+R write 8 speed (maximum)DVD+R DL write      2.4 speed (maximum)DVD+RW write 4 speed (maximum)DVD-RAM write 5 speed (maximum)CD read 24 speed (maximum)CD-R write 24 speed (maximum)CD-RW write 10 speed (maximum, Ultra-speed media)
User’s Manual 2-16The Grand TourAC adaptorThe AC adaptor can automatically adjust to any voltage ranging from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use this computer in almost any country/region. The adaptor converts AC power to DC power and reduces the voltage supplied to this computer.To recharge the battery, simply connect the AC adaptor to a power source and the computer. Refer to Chapter 6, Power and Power-Up Modes for details.Figure 2-10 The AC adaptor (2-pin plug)Figure 2-11 The AC adaptor (3-pin plug)■Depending on the model, a 2-pin plug or 3-pin plug set of the above may be bundled.■Do not use a 3-pin to 2-pin conversion plug.■The supplied power cord conforms to safety rules and regulations in the region the product is bought and should not be used outside this region. For use in other regions, please buy power cords that conform to safety rules and regulations in the particular region.Always use the TOSHIBA AC adaptor that was provided with your PC and the TOSHIBA Battery Charger (that may have been provided with your PC), or use AC adaptors and battery chargers specified by TOSHIBA to avoid any risk of fire or other damage to the PC. Use of an incompatible AC adaptor or Battery Charger could cause fire or damage to the PC possibly resulting in serious injury.
User’s Manual 3-1Chapter 3Features, Utilities and OptionsFeaturesThe computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits:ProcessorBuilt-in The computer is equipped with one of the following Intel® processors.■Intel® CoreTM Duo Processor, which incorporates a 2MB level2 cache memory. It also supports Enhanced Intel® SpeedStep®Technology.■Intel® CoreTM Solo Processor, which incorporates a 2MB level2 cache memory. It also supports Enhanced Intel® SpeedStep®Technology.■Intel® Celeron® M Processor, which incorporates a 1MB level2 cache memory.■Some models in the range are equipped with Intel® Centrino® Duo Mobile Technology, which is based on three separate technologies of Intel® CoreTM Duo processor, Intel® PRO/Wireless Network Connection, and Mobile Intel® 945 Express Chipset Family.■In addition, some models in the range are equipped with carry Intel®Centrino® Mobile Technology, which is based on three separate technologies of Intel® CoreTM Solo processor, Intel® PRO/Wireless Network Connection, and Mobile Intel® 945 Express Chipset Family.
User’s Manual 3-2Features, Utilities and OptionsMemoryPowerLegal Footnote (CPU)*2For more information on the Legal Footnote regarding CPU, please refer to the Legal Footnotes section in Appendix J. Click the *2.Slots 256, 512, 1,024 or 2,048 MB memory modules can be installed in the two memory slots for a maximum of 4,096 MB system memory.Video RAM There are two different types of graphics controllers. The Video RAM specifications will differ depending on the type of graphics controller used in the computer.■Intel internal graphics system model: Up to 128MB of main system memory may be allocated to this graphics controller for use as Video memory.■nVIDIA Quadro NVS 110M model: This graphics controller is equipped with 128MB of on-board video RAM (memory), and may use up to 128MB of main system memory as additional video memory for a combined total of up to 256MB of video memory.Legal Footnote (Memory (Main System))*3For more information on the Legal Footnote regarding Memory (Main System), please refer to the Legal Footnotes section in Appendix J. Click the *3.Battery pack The computer is powered by one rechargeable lithium-ion battery pack.Slice Expansion BatteryThis battery pack increases your computer's operating time when main battery pack is also installed.Legal Footnote (Battery Life)*4For more information on the Legal Footnote regarding Battery Life, please refer to the Legal Footnotes section in Appendix J. Click the *4.
User’s Manual 3-3Features, Utilities and OptionsDisksOptical disc driveRTC battery The internal RTC battery backs up the Real Time Clock (RTC) and calendar.AC adaptor The AC adaptor provides power to the system and recharges the batteries when they are low. It comes with a detachable power cord which will either have a 2-pin or 3-pin plug enclosure.Because it is universal, it can receive a range of AC voltage from 100 to 240 volts; however, the output current varies among different models. Using the wrong model can damage your computer. Refer to the AC adaptor section in chapter 2, The Grand Tour.Hard disk drive Available in five sizes.■40.0 billion bytes (37.26 GB)■60.0 billion bytes (55.89 GB)■80.0 billion bytes (74.53 GB)■100.0 billion bytes (93.16 GB)■120.0 billion bytes (111.79 GB)Part of the space in the hard disk drive is reserved as administration space.Legal Footnote (Hard Disk Drive (HDD) Capacity)*5For more information on the Legal Footnote regarding Hard Disk Drive (HDD) Capacity, please refer to the Legal Footnotes section in Appendix J. Click the *5.Drive This computer is equipped with one of the following drive types. The type of drive varies according to model.■DVD-ROM drive■DVD-ROM & CD-R/RW drive■DVD Super Multi drive Double Layer drive
User’s Manual 3-4Features, Utilities and OptionsDisplayThe computer’s LCD display panel supports high-resolution video graphics. The LCD screen can be set at a wide range of viewing angles for maximum comfort and readability. SoundBuilt-in 14.1" TFT LCD screen, 16 million colors, with a resolution of 1440 horizontal × 900 vertical pixels WXGA+.Legal Footnote (LCD)*6For more information on the Legal Footnote regarding LCD, please refer to the Legal Footnotes section in Appendix J. Click the *6.Graphics controller The graphics controller maximizes display performance. Refer to Display Controller and Modes section in Appendix B for more information.Legal Footnote (Graphics Processor Unit ("GPU"))*7For more information on the Legal Footnote regarding Graphics Processor Unit (“GPU”), please refer to the Legal Footnotes section in Appendix J. Click the *7.Sound system The Windows sound system compatible sound system provides output to internal speakers and input from one internal microphone as well as supports jacks for an external microphone and headphones.
User’s Manual 3-5Features, Utilities and OptionsCommunicationsModem An internal modem provides capability for data and fax communication. It supports V.90 (V.92). Refer to V.90 section in Appendix E. The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line. It is preinstalled as a standard device in some markets. Both of V.90 and V.92 are supported only in USA and Canada. Only V.90 is available in other regions.LAN The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) and Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T). It is preinstalled as a standard device in some markets.Bluetooth Some computers in this series are equipped with Bluetooth functions. Bluetooth wireless technology eliminates the need for cables between electronic devices such as computers and printers. Bluetooth provides fast, reliable, and secure wireless communication in a small space. Wireless LAN Some computers in this series are equipped with a Wireless LAN card that is compatible with other LAN systems based on Direct Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing radio technology that complies with the IEEE 802.11 Standard (Revision A, B or G).Legal Footnote (Wireless LAN)*8For more information on the Legal Footnote regarding Wireless LAN, please refer to the Legal Footnotes section in Appendix J. Click the *8.
User’s Manual 3-6Features, Utilities and OptionsSpecial featuresThe following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use.Hot keys Hot keys are specific key combinations that let you quickly change the system configuration directly from the keyboard without running a system program.Display automatic power offThis feature automatically cuts off power to the computer’s LCD display panel when there is no keyboard input for a specified time. Power is restored when any key is pressed. You can specify the time in the Monitor power off item of the Basic Setup tab in TOSHIBA Power Saver.HDD automatic power offThis feature automatically cuts off power to the hard disk drive when it is not accessed for a specified time. Power is restored when the hard disk is accessed. You can specify the time in the HDD power off item of the Basic Setup tab in TOSHIBA Power Saver.System automatic Standby/HibernationThis feature automatically shuts down the system into either Standby Mode or Hibernation Mode when there is no input or hardware access for a specified time. You can specify the time and select either the System Standby or System Hibernation item of the Basic Setup tab in TOSHIBA Power Saver.Keypad overlay A ten-key pad is integrated into the keyboard. Refer to the Keypad overlay section in Chapter 5, The Keyboard, for instructions on using the keypad overlay.Power on password Two levels of password security, supervisor and user, are available to prevent unauthorized access to your computer.Instant security A hot key function blanks the LCD screen and disables the computer providing data security.Intelligent power supplyA microprocessor in the computer’s intelligent power supply detects the battery’s charge and calculates the remaining battery capacity. It also protects electronic components from abnormal conditions, such as voltage overload from an AC adaptor. You can monitor remaining battery capacity by using the Battery remaining item in TOSHIBA Power Saver.
User’s Manual 3-7Features, Utilities and OptionsBattery save mode This feature lets you save battery power. You can specify the Power Save Mode in the Profile item in TOSHIBA Power Saver.Panel power on/off This feature turns power to the computer off when the computer’s LCD display panel is closed and turns it back on when the computer’s LCD display panel is opened. You can specify the setting in the When I close the lid item of the Setup Actions tab in TOSHIBA Power Saver.Low battery automatic hibernationWhen battery power is exhausted to the point that computer operation cannot be continued, the system automatically enters Hibernation and shuts down. You can specify the setting in the Setup Actions tab in TOSHIBA Power Saver.Heat dispersal To protect from overheating, the CPU has an internal temperature sensor. If the computer’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered. Use the Cooling Method item of the Basic Setup tab in TOSHIBA Power Saver.Optical Drive Power Use this to turn the power of the optical disc drive on or off. Clicking on the Optical Drive Power icon in the taskbar will turn the power to the optical disc drive on or off. If the Optical Drive Power is set to off, the disc tray will not open even if the eject button is pushed - in this instance the power to the drive can be turned on by again clicking the Optical Drive Power icon.TOSHIBA HDD ProtectionUsing the acceleration sensor built in the computer, the TOSHIBA HDD Protection function detects vibrations and shocks, and automatically moves the hard disk drive's read/write head to a safe position to reduce the risk of damage that could be caused by head-to-disk contact. Refer to the Using the Hard Disk Drive (HDD) Protectionsection in Chapter 4, Operating Basics, for details.The TOSHIBA HDD Protection function does not guarantee that the hard disk drive will not be damaged.
User’s Manual 3-8Features, Utilities and OptionsUtilitiesThis section describes preinstalled utilities and tells how to start them. For details on usage and operation, refer to each utility’s online manual, help files or readme.txt files.Hibernation This feature lets you turn off the power without exiting from your software. The contents of main memory are saved to the hard disk so that when you next turn the power on again, you can continue working right where you left off. Refer to the Turning on the power section in Chapter 1, Getting Started, for details.Standby If you have to interrupt your work, you can turn off the power without exiting from your software. Data is maintained in the computer’s main memory. When you turn on the power again, you can continue working right where you left off.TOSHIBA Power SaverTo access this power savings management program, click start, click Control Panel, click Performance and Maintenance and click the TOSHIBA Power Saver icon.HW Setup This program lets you customize your hardware settings according to the way you work with your computer and the peripherals you use. To start the utility, to access this utility, click start, click Control Panel, click Printers and Other Hardware and click the TOSHIBA HWSetupicon.TOSHIBA Controls This utility have a section to let you do the following:■Buttons: Assign applications or functions to the 4 buttons (TOSHIBA Assist, TOSHIBA Presentation, Application1, Application2).
User’s Manual 3-9Features, Utilities and OptionsFingerprint utility This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints. By enrolling the ID and password to the fingerprint authentication device, it is no longer necessary to input the password from the keyboard. Fingerprint feature enables you to:■Logon to Windows and access a security-enabled homepage through IE (Internet Explorer).■Files and folders can be encrypted/decrypted and third party access to them prevented.■Disable the password-protected screen-saver when returning from power-saving (e.g., standby) mode.■Authentication of the User Password (and, if applicable, the HDD(Hard Disk Drive) Password) when booting up the computer (Power-on Security).■Single Sign-on featureFn-esse This Windows program lets you define your own “shortcut” keys to quickly launch applications and speed your work in Windows. To start the utility, click start, point to All Programs, point to TOSHIBA, point to Utilities and click Fn-esse.DVD Video Player The DVD Video Player is used to play DVD-Video. It has an on-screen interface and functions. Click start, point to All Programs,point to InterVideo WinDVD, then click InterVideo WinDVD.Bluetooth Stack for Windows by Toshiba This software enables communication between remote Bluetooth devices.Bluetooth cannot be used in models that do not have a Bluetooth module installed.TOSHIBA SD Memory Boot UtilityThe TOSHIBA SD memory boot utility allows you to create a bootable SD memory card to start the system. You can access the TOSHIBA SD Memory Boot Utility from the menu bar by clicking start, point to All Programs, point to TOSHIBA, point to Utilities and click SD Memory Boot Utility.TOSHIBA Zooming UtilityThis utility allows you to enlarge or reduce the icon size on the desktop or the application window.
User’s Manual 3-10Features, Utilities and OptionsRecordNow! Basic for TOSHIBAYou can create CD/DVDs in several formats including audio CDs that can be played on a standard stereo CD player and data CD/DVDs to store the files and folders on your hard disk drive. This software can be used on models equipped with a DVD-ROM & CD-R/RW drive or a DVD Super Multi drive.TOSHIBA Assist TOSHIBA Assist is a graphical user interface that provides easy access to help and services. It is the default function launched by the TOSHIBA Assist button.TOSHIBA PC Diagnostic ToolTOSHIBA PC Diagnostic Tool displays the basic information on the computer's configuration and allows some of the built-in devices functionality to be tested. To start TOSHIBA PC Diagnostic Tool, click start, point to All Programs, point to TOSHIBA, point to Utilities and click PCDiagnostic Tool.TOSHIBA Mobile ExtensionThis utility enhances the function of your computer when docking to an optional TOSHIBA Express Port Replicator. To access the utility, select TOSHIBA Mobile Extension from the TOSHIBA Assist application.TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities to allow easy control of communication devices and network connections. TOSHIBA ConfigFree also allows you to find communication problems and create profiles for easy switching between locations and communication networks. To start ConfigFree, click start, point to All Programs,point to TOSHIBA, point to Networking and click ConfigFree.TOSHIBA TouchPad On/Off UtilityThis utility allows you to disable/enable the Touch Pad using the Fn +F9 Hot key.TOSHIBA Mic Effect The TOSHIBA Mic Effect utility provides you with Echo Canceller and Microphone Array functions.For more instructions for this software, click start, point to All Programs, point to TOSHIBA,point to Utilities and click TOSHIBA Mic Effect Help.TOSHIBA Password UtilityThis utility lets you set a password that restricts access to the computer.TOSHIBA AccessibilityThis utility lets you make the Fn key sticky, that is, you can press it once, release it, and they press an "F number" key. The Fn key remains active until another key is pressed.
User’s Manual 3-11Features, Utilities and OptionsDLA for TOSHIBA DLA (Drive Letter Access) is the packet writing software which provides the function to write files and/or folders to DVD-RW, CD-RW and DVD+RW discs via a drive letter like a floppy disk or other removable disks.TOSHIBA Hotkey Utility for Display DevicesThis utility allows you to select the display device as well as change the display resolution on that device. Press the Fn +F5 Hot key to change the active display device and press the Fn +Space Hot key to change the display resolution.TOSHIBA SD Memory Card FormatThe TOSHIBA SD Memory Card Format utility allows you to format an SD memory card by the SD standard format.CD/DVD Drive Acoustic SilencerThis utility allows you to configure the read speed of the CD drive. You can either configure Normal Mode, which operates the drive at its maximum speed for quick data access, or Quiet Mode which runs it at single speed for CD audio play back and which lessens operational noise.This utility has no effect when access DVD media.TOSHIBA Accelerometer UtilitiesWhen TOSHIBA Accelerometer Utilities is enabled, you can invoke the Start menu, switch active windows or launch predefined applications by shaking the computer vertically or horizontally, or by tilting it.You can start TOSHIBA Accelerometer Utilities by clicking start, click All Programs, click TOSHIBA, click Tablet PC and Setup for TOSHIBA Accelerometer Utilities.The Setting of TOSHIBA Accelerometer Utilities screen appears.
User’s Manual 3-12Features, Utilities and OptionsOptional devicesOptional devices can expand the computer’s capabilities and its versatility. This section describes connection or installation of the following devices.Cards/memory■PC card■Bridge media slot■SD card (SD memory card, SDIO card)■Memory Stick/Memory Stick Pro■xD picture card■MultiMediaCard■Memory expansionPower devices■Battery Pack■Universal AC Adaptor■Slice Expansion Battery■Battery ChargerTOSHIBA Tablet Access Code Logon UtilityIf a Windows password has been set, you can logon to the operating system by entering a handwriting signature into the dialog box using the Tablet PC Pen when prompted.TOSHIBA Rotation UtilityThis utility controls the screen orientation setting for both PC mode and Tablet mode.You can set four types of orientation setting:■Primary landscape■Primary portrait■Secondary landscape■Secondary portraitThe default setting of PC mode is Primary Landscape while that for Tablet mode is Primary Portrait.To start TOSHIBA Rotation Utility, Click start,click All Programs, click TOSHIBA, click Tablet PC and Rotation Utility.
User’s Manual 3-13Features, Utilities and OptionsPeripheral devices■USB FDD Kit■Tablet PC Pen■Reserve pen■External monitor■TV■i.LINK (IEEE1394)■TOSHIBA Express Port Replicator ■Bluetooth USB Adaptor■Wireless Optical Mouse with Bluetooth Technology■Wireless Stereo Headset with Bluetooth TechnologyOther■Security lockPC cardThe computer is equipped with a PC card slot that can accommodate a Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards. CardBus supports the new standard of 32-bit PC cards. The bus provides superior performance for the greater demands of multimedia data transmission.Inserting a PC cardWindows hot-install feature lets you insert PC cards while the computer’s power is on.To insert a PC card, follow the steps below:1. Insert a PC card in the PC card slot.PC cards can sometimes become hot during PC operation. Before you remove a PC card always wait for it to cool. You could get burned removing a hot PC card.Do not insert a PC card while the computer is in Standby or Hibernation Mode. Some cards might not work properly.
User’s Manual 3-14Features, Utilities and Options2. Press gently to ensure a firm connection.Figure 3-1 Inserting the PC card3. After inserting the PC card, refer to the PC card’s documentation and check the configuration in Windows to make sure it is appropriate for your PC card.Removing a PC cardTo remove the PC card, follow the steps below.1. Open the Safely Remove Hardware icon on the Task Bar.2. Point to PC card and click.3. Press the PC card eject button to extend it.4. Press the extended eject button to pop the card out slightly. 5. Grasp the PC card and draw it out.Figure 3-2 Removing the PC cardPC cardPC card slotIf the PC card is not inserted all the way, the eject button may not cause it to pop out sufficiently to allows it to be grasped. Be sure to push the PC card firmly into the computer and slide the eject button again.PC cardPC card eject button
User’s Manual 3-15Features, Utilities and OptionsBridge media slotThis slot lets you insert SD memory card, SDIO card, Memory Stick (Pro), xD picture card or MultiMediaCard. Media careObserve the following precautions when handling the card.Card care■Do not twist or bend cards.■Do not expose cards to liquids or store in humid areas or lay media close to containers of liquid.■Do not touch the metal part of a card or expose it to liquids or let it get dirty.■After using card, return it to its case.■The card is designed so that it can be inserted only one way. Do not try to force the card into the slot.■Do not leave a card partially inserted in the slot. Press the card until you hear it click into place.Memory card care■Set the write-protect switch to the lock position, if you do not want to record data.■Memory cards are consumable items, so make sure you back up important data.■Do not write to an SD card if the battery power is low. Low power could affect writing accuracy.■Do not remove an SD card while read/write is in progress.This Bridge media slot supports the following cards.■SD card (SD memory card, SDIO card)■Memory Stick■Memory Stick PRO■xD picture card■MultiMediaCardPrecautions on using cards.Please note that not all cards have been tested and verified to work correctly. Therefore, it is not possible to guarantee that all cards will operate properly.For more details on using memory cards, see manuals accompanying the cards.
User’s Manual 3-16Features, Utilities and OptionsSD cardSet the SD-card type SD memory cards and Bluetooth® SDIO cards in the Bridge Media slot.Inserting an SD cardTo insert an SD card, follow the steps below.1. Insert an SD card in the Bridge media slot.2. Press gently to ensure a firm connection.Figure 3-3 Inserting an SD card Keep foreign objects out of the Bridge media slot. Never allow metal objects, such as screws, staples and paper clips, to enter the PC or keyboard. Foreign metal objects can create a short circuit, which can cause PC damage and fire, possibly resulting in serious injury.SD cardBridge media slot■Make sure the SD card is oriented properly before you insert it. ■Do not turn the computer off or switch to Standby Mode or Hibernate Mode while files are being copied - doing so may cause data to be lost.
User’s Manual 3-17Features, Utilities and OptionsRemoving an SD cardTo remove an SD card, follow the steps below.1. Open the Safely Remove Hardware icon on the Task Bar.2. Point to SD card and click.3. Push in the card and release it to pop the card out slightly.4. Grasp the card and remove it.Figure 3-4 Removing an SD card SD memory cardSD cards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use SD card flash-memory. The cards have a high level of security and copy protection features. SD cardBridge media slot■Make sure the Bridge media slot indicator is out before you remove the SD card or turn off the computer’s power. If you remove the SD card or turn off the power while the computer is accessing the SD card you may lose data or damage the card.■Do not remove an SD card while the computer is in Standby or Hibernation mode. The computer could become unstable or data in the SD card could be lost.SD memory cards comply with SDMI (Secure Digital Music Initiative), which is a technology adopted to prevent unlawful copy or playback of digital music. For this reason, you cannot copy or playback protected material on another computer or other device. You may not use the reproduction of any copyrighted material except for your personal enjoyment.
User’s Manual 3-18Features, Utilities and OptionsFormatting an SD cardSD memory cards are sold already formatted in conformity to specific standards. If you format the SD card again, be sure to format it with the TOSHIBA SD Memory Card Format utility, not with the format commands provided within Windows.In order to run TOSHIBA SD Memory Card Format, click start, point to AllPrograms, point to TOSHIBA, point to Utilities and click SD Memory Card Format.The TOSHIBA SD Memory Card Format utility does not format the protected area of the SD memory card. Should you need to format all areas of the memory card, including the protected area, you will need to obtain an appropriate application that applies the copy protection system.SDIO cardAdd the Bluetooth® wireless communication function to a computer with the SDIO card.Memory Stick/Memory Stick ProThe computer is equipped with a Bridge media slot that can accommodate Memory Stick/Memory Stick Pro flash memory cards with various memory capacities. Memory Stick let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use Memory Stick technology.Write protectionMemory Stick can be write protected to safeguard your data. To write-protect a Memory Stick, slide the lock on the back of the Memory Stick to the lock position.Inserting a Memory StickTo insert a Memory Stick, follow the steps below. 1. Insert the Memory Stick into the Bridge media slot.Keep foreign objects out of the Bridge media slot. Never allow metal objects, such as screws, staples and paper clips, to enter the PC or keyboard. Foreign metal objects can create a short circuit, which can cause PC damage and fire, possibly resulting in serious injury.■The slot does not support Magic Gate functions.■Memory Stick Duo/PRO Duo and the Memory Stick adaptor are not compatible with the Bridge media slot. Do not insert Memory Stick Duo/PRO Duo into the slot. Data may be lost or damaged if you use any card other than those supported.
User’s Manual 3-19Features, Utilities and Options2. Press gently to ensure a firm connection.Figure 3-5 Inserting a Memory StickRemoving a Memory StickTo remove a Memory Stick, follow the steps below. 1. Open the Safely Remove Hardware icon on the Task Bar. 2. Point to Memory Stick and click.3. Push in the card and release it to pop the card out slightly.4. Grasp the card and remove it.xD picture cardThe computer is equipped with a Bridge media slot that can accommodate xD picture cards with various memory capacities. The xD picture card let you easily transfer data from devices, such as digital cameras that use xD picture card flash-memory. Memory StickBridge media slot■Make sure the Bridge media slot indicator is out before you remove the Memory Stick or turn off the computer's power. If you remove the Memory Stick or turn off the power while the computer is accessing the Memory Stick you may lose data or damage the card.■Do not remove a Memory Stick while the computer is in Standby or Hibernation mode. The computer could become unstable or data in the Memory Stick could be lost.Keep foreign objects out of the Bridge media slot. Never allow metal objects, such as screws, staples and paper clips, to enter the PC or keyboard. Foreign metal objects can create a short circuit, which can cause PC damage and fire, possibly resulting in serious injury.
User’s Manual 3-20Features, Utilities and OptionsInserting an xD picture cardTo insert an xD picture card, follow the steps below. 1. Insert the xD picture card into the Bridge media slot.2. Press gently to ensure a firm connection.Figure 3-6 Inserting an xD picture cardRemoving an xD picture cardTo remove an xD picture card, follow the steps below. 1. Open the Safely Remove Hardware icon on the Task Bar. 2. Point to xD picture card and click.3. Push in the card and release it to pop the card out slightly.4. Grasp the card and remove it.MultiMediaCardThe computer is equipped with the Bridge media slot that can accommodate MultiMediaCard flash memory technology with various memory capacities. MultiMediaCards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use MultiMediaCard flash-memory. The cards have a high level of security and copy protection features.xD picture cardBridge media slot■Make sure the Bridge media slot indicator is out before you remove the xD picture card or turn off the computer's power. If you remove the xD picture card or turn off the power while the computer is accessing the xD picture card you may lose data or damage the card.■Do not remove an xD picture card while the computer is in Standby or Hibernation mode. The computer could become unstable or data in the xD picture card could be lost.Keep foreign objects out of the Bridge media slot. Never allow metal objects, such as screws, staples and paper clips, to enter the PC or keyboard. Foreign metal objects can create a short circuit, which can cause PC damage and fire, possibly resulting in serious injury.
User’s Manual 3-21Features, Utilities and OptionsInserting a MultiMediaCardTo insert a MultiMediaCard, follow the steps below.1. Insert the MultiMediaCard into the Bridge media slot.2. Press gently to ensure a firm connection.Figure 3-7 Inserting a MultiMediaCard Removing a MultiMediaCardTo remove a MultiMediaCard, follow the steps below.1. Open the Safely Remove Hardware icon on the Task Bar.2. Point to MultiMediaCard and click.3. Push in the card and release it to pop the card out slightly.4. Grasp the card and remove it.Figure 3-8 Removing a MultiMediaCard MultiMediaCards comply with SDMI (Secure Digital Music Initiative), which is a technology adopted to prevent unlawful copy or playback of digital music. For this reason, you cannot copy or playback protected material on another computer or other device. You may not use the reproduction of any copyrighted material except for your personal enjoyment.MultiMediaCardBridge media slotMake sure the MultiMediaCard is oriented properly before you insert it. MultiMediaCardBridge media slot
User’s Manual 3-22Features, Utilities and OptionsMemory expansionYou can install additional memory in the computer’s memory module slot to increase the amount of RAM. This section describes how to install and remove a memory module.■Make sure the Bridge media slot indicator is out before you remove the MultiMediaCard or turn off the computer’s power. If you remove the MultiMediaCard or turn off the power while the computer is accessing the MultiMediaCard you may lose data or damage the card.■Do not remove a MultiMediaCard while the computer is in Standby or Hibernation mode. The computer could become unstable or data in the MultiMediaCard could be lost.■Place a mat beneath the computer to prevent scratching or damaging the computer's lid when installing/replacing the memory module. Avoid mats made of materials that generate static electricity.■When you install or remove a memory module, ensure that you do not touch any other internal areas of the computer.■Use only memory modules approved by TOSHIBA.■Do not try to install or remove a memory module under the following conditions as you can damage the computer and/or the module, and you risk losing data:a. The computer is turned on.b. The computer was shut down using either Standby Mode or Hibernation mode.c. Wake-up on LAN is enabled.d. Wake-up on Wireless LAN is enabled.■Be careful not to let screws or other foreign matter fall into the computer. It could cause malfunction or electric shock.■Expansion memory is a precision electronic component that may be fatally damaged by static electricity. Since the human body can carry static electricity, it is important that you discharge yourself before touching or installing any expansion memory modules. To discharge your body’s static electricity, simply touch any metal close to you with bare hands.
User’s Manual 3-23Features, Utilities and OptionsIf you install a memory module that is not compatible with the computer,  the power LED will flashes (on for 0.5 seconds, off for 0.5 seconds) in the following ways;If there is only an error in Slot A: repeatedly flashes orange twice, then green.If there is only an error in Slot B: repeatedly flashes orange, then green twice.If there is an error in Slot A and in Slot B: repeatedly flashes orange twice, then green twice.In all instances you should shut down the computer and remove the incompatible module(s).Installing a memory moduleThere are slots for two memory modules. The procedures are the same for installing either module.1. Set the computer to boot mode and turn the computer’s power off. Make sure the Power indicator is off. Refer to the Turning on the power section in Chapter 1, Getting Started.2. Remove AC adaptor and all cables connected to the computer.3. Turn the computer upside down and remove the battery pack. Refer to Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, for details.4. Turn your computer over.5. Push the display latch on the front of the computer and open the LCD display panel.6. Remove the 2 keyboard braces at the top and bottom of the keyboard. Slip your finger under a notch at the end of the keyboard braces and lift up to release latches and remove the keyboard braces.Figure 3-9 Removing the keyboard bracesUse a point size 1 Phillips screwdriver to remove and fasten the screws. Use of an incorrect screwdriver can damage the screw heads.Keyboard braces
User’s Manual 3-24Features, Utilities and Options7. Remove two screws securing the keyboard.8. Open the latch which holds the keyboard in place, then lift the back of the keyboard toward you, and lay it face down on the palm rest.Figure 3-10 Removing two screws and rotate the keyboard9. Remove the two screws and take off the memory module cover.Figure 3-11 Removing the memory module coverUse a point size 1 Phillips screwdriver.■When you move the keyboard forward, do not touch the keys. Doing so could cause misalignment. Hold the keyboard by the sides and lay it gently on the palm rest.■The keyboard is connected to the computer by a keyboard ribbon cable. Be careful not to apply tension to this cable when you lift up the keyboard. Do not try to disconnect this cable.ScrewsScrewsMemory module cover■Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems.■The memory module cover will be hot after using the computer for long periods of time. Exercise caution when removing.
User’s Manual 3-25Features, Utilities and Options10. Fit the memory module's connectors into the socket at about a 45 degree angle and push the module down until latches on either side snap into place.Align the notch of the memory module with that of the memory slot and gently insert the module into the slot.Figure 3-12 Installing the memory module11. Screw in the two screws and replace the memory module cover.Figure 3-13 Seating the memory module coverThe slot A is reserved for main memory. Use the slot B for expanded memory. If only one card is installed, use the slot A.Slot BSlot AScrewsMemory module cover
User’s Manual 3-26Features, Utilities and Options12. Tuck the keyboard ribbon cable into the groove under the palm rest.Figure 3-14 Tuck the keyboard ribbon cable13. Insert the tabs on the front of the keyboard into the corresponding notches on the computer and place the keyboard down.14. Screw the two screws and secure the keyboard.15. Set the keyboard braces into its groove and press down to secure the latches.16. Install the battery pack. Refer to Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, for details.17. Turn your computer over.18. Turn the power on and make sure the added memory is recognized. Click start, click Control Panel, click Performance and Maintenanceand select the System icon. Open System Properties window and click General tab.Removing a memory moduleTo remove the memory module, make sure the computer is in boot mode then:1. Set the computer to boot mode and turn the computer’s power off. Make sure the Power indicator is off.2. Remove AC adaptor and all cables connected to the computer.Keyboard ribboncableDo not bend the keyboard ribbon cable.When seating the keyboard, be sure to connect the circuit board if the keyboard ribbon cable was pulled out while you were removing the keyboard.Be sure to use all two screws removed in step 7. Make sure no screw was dropped into the computer. Make sure no foreign matter can be found.
User’s Manual 3-27Features, Utilities and Options3. Turn the computer upside down and remove the battery pack. Refer to Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, for details.4. Follow steps 4 through 9 in Installing memory module to remove the memory module cover.5. Push the latches to the outside to release the memory module. A spring will force one end of the memory module up.6. Grasp the sides of the module and pull it out.Figure 3-15 Removing the memory module7. Rotate the keyboard back into place and secure the keyboard brace as described in the previous section.8. Install the battery pack. Refer to Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, for details.9. Turn your computer over.Battery PackYou can increase the portability of the computer with additional battery packs. If you’re away from an AC power source and your battery runs low, you can replace it with a freshly charged battery. Refer to Chapter 6, Powerand Power-Up Modes.■If you use the computer for a long time, the memory modules and the circuits locating close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them. Or you will get burnt if you touch any of them.■Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems.Latches
User’s Manual 3-28Features, Utilities and OptionsUniversal AC AdaptorIf you frequently transport the computer between different sites such as your home and office, purchasing an AC adaptor for each location will reduce the weight and bulk of your carrying load.Slice Expansion BatteryThis battery pack increases your computer's operating time when a main battery pack is also installed. For details on using the battery pack, follow the steps below.Connecting the Slice Expansion BatteryFollow the steps below to connect the Slice Expansion Battery to the computer1. Be sure the computer’s power is off and all cables are disconnected.2. Lay the computer upside down.3. Remove the protective cap from the Slice Expansion Battery.4. Open the latches on the Slice Expansion Battery (1).5. Fit the battery's tab into the groove on the underside of the computer (2).6. Connect the battery's connector to the docking port (3).7. Close the latches to secure the Slice Expansion Battery to the computer (4).Figure 3-16 Securing the latchesWhen handling Slice Expansion Battery, be careful not to short circuit the terminals. Also do not drop, hit or otherwise apply impact; do not scratch or break the casing and do not twist or bend the latches of it.LatchLatch Tab
User’s Manual 3-29Features, Utilities and OptionsDisconnecting the Slice Expansion BatteryFollow the steps below to disconnect the Slice Expansion Battery to the computer.1. Save your work.2. Turn the computer’s power off. Make sure the Power indicator is off.3. Remove all cables connected to the computer.4. Lay the computer upside down.5. Push the release latches in the direction of the arrows (1).6. Lift off the Slice Expansion Battery (2).Figure 3-17 Removing the Slice Expansion Battery7. Be sure to replace the protective cap before storing the Slice Expansion Battery.Battery ChargerThe battery charger provides a convenient way to charge battery packs without requiring the use of your computer. The battery charger holds up to two battery packs (lithium ion).USB FDD KitThe USB floppy disk drive accommodates 1.44-megabyte or 720-kilobyte floppy disks and connects to the USB port. It is supplied as standard with some models and as an option with others.LatchLatch
User’s Manual 3-30Features, Utilities and OptionsConnecting USB floppy disk driveTo connect the drive, plug the floppy disk drive’s USB connector into a computer’s USB port. Figure 3-18 Connecting the USB floppy disk driveDisconnecting USB floppy disk driveWhen you have finished using the USB floppy disk drive, follow the procedures below to disconnect it:1. Wait for the indicator light to go out to make sure all floppy disk activity has stopped. 2. Click the Safely Remove Hardware icon on the Task Bar.3. Click USB floppy disk drive device that you want remove.4. Pull the floppy disk drive’s USB connector out of the computer’s USB port.Make sure the connector is properly aligned with the socket. Do not try to force the connection, doing so can damage the connecting pins.USB connector USB portIf you connect the USB floppy disk drive after turning on the computer, it will take about 10 seconds for the computer to recognize the drive. Do not disconnect and reconnect before 10 seconds has elapsed.If you disconnect the USB floppy disk drive or turn off the power while the computer is accessing the drive you may lose data or damage the floppy disk or the drive.
User’s Manual 3-31Features, Utilities and OptionsTablet PC PenUse it as a spare to your computer. Spare pen tip and draw-out tool are included. Refer to Chapter 4, Operating Basics, for the detailed usage.Reserve PenSupplied pen uses a pen instead of Supplied pen at the time of loss or breakage. Refer to Chapter 4, Operating Basics, for the detailed usage.External monitorAn external analog monitor can be connected to the external monitor port on the computer. To connect a monitor, follow the steps below.1. Turn the computer’s power off.2. Connect the monitor cable to the external monitor port and tighten the screws on the left and right hand side.Figure 3-19 Connecting the monitor cable to the external monitor port3. Turn the monitor’s power on.4. Turn the computer’s power on. When you turn on the power, the computer automatically recognizes the monitor and determines whether it is color or monochrome.However, the Windows Desktop appears on a display device that you used last time to shut down your computer, if the display device exists when you turn on the power.To change the display settings, press Fn + F5. If you disconnect the external monitor before you turn the computer’s power off, be sure to press Fn + F5 to switch to the internal display. Refer to Chapter 5, The Keyboard,for details on using hot keys to change the display setting.External monitor portMonitor cable
User’s Manual 3-32Features, Utilities and OptionsTVYou can connect a television set to the S-Video out port on the computer. Follow the steps below.As an example, this is the setup method for the TOSHIBA Assist button.Buttons other than the TOSHIBA Assist button can also be re-assigned.Using the TOSHIBA Assist button1. Connect the TV adaptor cable’s S-Video plug to the S-Video out port on the computer.Figure 3-20 Connecting the TV adaptor cable to the S-Video out port2. Connect the TV adaptor cable’s S-Video plug to the S-Video out port on the TV.3. Press the TOSHIBA Assist button.You can use the hot keys Fn + F5 to change the display device. Refer to Chapter 5, The Keyboard.To use "TV OUT" function by "TOSHIBA Assist button", it is necessary to change the settings of "TOSHIBA Assist button" in advance.To open "TOSHIBA Controls" properties, click start, click Control Panel,click Printers and Other Hardware, select "TOSHIBA Controls", and set "TV OUT" to "TOSHIBA Assist button" on "Buttons" tab.S-Video out portTV adaptor cable
User’s Manual 3-33Features, Utilities and OptionsChanging the resolutionIf you want to change the resolution, follow the steps below.1. Open Display properties and select the Settings tab.2. Select Advanced.3. Select the Adapter tab, then select List all modes.4. Select a resolution from the menu.Displaying movies on a TV or CRTThis section describes how to set up your system to display movies simultaneously on your computer’s internal LCD and on an external TV or CRT monitor. Please use the following settings if your computer is equipped with the Quadro NVS 110M video card.Follow the steps below.1. Open the Control Panel and click Appearance and Themes.2. Click Display.3. Select the Settings tab and click Advanced button.If a television is connected to the computer, set the TV type in Display Properties. Follow the steps below.nVIDIA Quadro NVS 110M modela. Click start and click Control Panel.b. Click Appearance and Themes and click the Display to open the Display Properties window.c. Click the Settings tab and click the Advanced button.d. Click the Quadro NVS 110M tab, click Device Settings and click Select TV format.e. Select Advanced and select TV Settings in the TV Settings window.f. Select the Signal format box and select the format that your TV supports.Intel internal graphics system modela. Click start and click Control Panel.b. Click Appearance and Themes and click the Display to open the Display Properties window.c. Click the Settings tab and click the Advanced button.d. Click the Intel® Graphics Media Accelerator Driver for Mobiletab, click Graphics Properties... button.e. Select Television in the Display Device tab.f. Select the TV format from the Video Standard pull down menu in the Display Setting tab.
User’s Manual 3-34Features, Utilities and Options4. Select the Quadro NVS 110M tab.a. Click the Quadro NVS 110M button.b. Click Full Screen Video in the small menu.c. From the Full screen device drop down menu, select Primary display or Secondary display to enable movie display on an external TV or CRT monitor. Primary Device: Movies will be displayed full screen on the computer's internal LCD and in a window on the TV or CRT monitor. Secondary Device: Movies will be displayed full screen on the TV or CRT monitor and in a window on the computer's internal LCD.Disable: Movies will not be displayed on a TV or CRT monitor.d. Click OK.e. Click OK in the Display Properties screen.i.LINK (IEEE1394)i.LINK (IEEE1394) is used for high-speed data transfer for a range of compatible devices such as:■Digital video cameras■Hard disk drives■MO drives■Writable optical disc drivesPrecautions■Make a back-up of your data before transferring it to the computer. There is a possibility that the original data will be damaged. There is a particular risk that some frames will be deleted in the case of digital video transfer. TOSHIBA assumes no liability for such loss of data.■Do not transfer data in areas where static electricity is easily generated or in areas subjected to electronic noise. Data can be destroyed.■If you are transferring data through an IEEE1394 hub, do not connect or disconnect other devices from the hub during data transfer. There is a likelihood that data will be damaged. Connect all devices to the hub before you turn on the computer’s power.■You may not use any copyrighted video or music data copied from a video camera except for your personal enjoyment.■If you connect/disconnect an i.LINK device to/from another i.LINK device that is currently exchanging data with the computer, data frames might be dropped. Even if the above does not set up, there are some as which the movies is simultaneously displayed depending on the type of the movies.i.LINK uses a four-pin connector, which does not carry any electric current. External devices will need their own power supply to operate.
User’s Manual 3-35Features, Utilities and Options■Make sure data transfer has ended or turn off the computer, before you:■Connect/disconnect an i.LINK device to/from the computer.■Connect/disconnect an i.LINK device to/from another i.LINK device that is connected to the computer.Connecting1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394) cable into the computer.Figure 3-21 Connecting the i.LINK (IEEE1394) cable into the computer2. Plug the other end of the cable into the device.Note the following when you use i.LINK:■You may need to install drivers for your i.LINK devices.■Not all i.LINK devices have been tested. Therefore, compatibility with all i.LINK devices cannot be guaranteed.■Some devices might not support standby or automatic off functions.■Do not connect or disconnect an i.LINK device while it is using an application or when the computer is automatically shutting it down to save power. Data might be destroyed.Disconnecting1. Open the Safely Remove Hardware icon on the Task Bar.2. Point to i.LINK (IEEE1394) device and click.3. Disconnect the cable from the computer then from the i.LINK device.i.LINK (IEEE1394)connectori.LINK (IEEE1394)portRefer also to the documentation that came with your i.LINK device.
User’s Manual 3-36Features, Utilities and OptionsTOSHIBA Express Port ReplicatorIn addition to the ports available on the computer, the TOSHIBA Express Port Replicator. The TOSHIBA Express Port Replicator connects directly to the docking interface on the underside of the computer. The AC adaptor connects the TOSHIBA Express Port Replicator to a power source.The following ports and accessories are available on the TOSHIBA Express Port Replicator.■RJ45 LAN jack■External monitor port■DC IN 15V jack■Security lock slot■Universal Serial Bus 2.0 port (four)■DVI port (This port is not supported by the computer)The computer must be configured properly before connecting to a LAN. Logging onto a LAN using the computer’s default settings could cause a malfunction in LAN operation. Check with your LAN administrator regarding set-up procedures.■You must connect the AC adaptor before you connect to a TOSHIBA Express Port Replicator.■When a TOSHIBA Express Port Replicator is connected to the computer, you can not use the following computer’s ports: LAN jack and External monitor port.■When connecting an AC Adaptor to the TOSHIBA Express Port Replicator, use only the AC Adaptor included with TOSHIBA Express Port Replicator. Do not use the computer’s AC Adaptor.■As the port operation of all DVI (Digital Visual Interface) monitors has not been confirmed, some DVI monitors may not function properly.■Set the TOSHIBA Express Port Replicator's Slide Adjuster to SLIDE position #6 when connecting this computer to the TOSHIBA Express Port Replicator. Refer to the TOSHIBA Express Port Replicator User's Manual for more details on connection methods.
User’s Manual 3-37Features, Utilities and OptionsBluetooth USB AdaptorWhen connected to one of the computer's USB ports, the Bluetooth USB adaptor allows wireless communications to be carried out with Bluetooth-compatible equipment.Wireless Optical Mouse with Bluetooth TechnologyThe Wireless optical mouse with Bluetooth Technology is an optical mouse that is compatible with the Bluetooth wireless standard.Wireless Stereo Headset with Bluetooth TechnologyThe Bluetooth Wireless Stereo Headset provides stereo headphones that are compatible with the Bluetooth wireless standard.Security lockSecurity locks enable you to anchor your computer and optional TOSHIBA Express Port Replicator to a desk or other heavy object to help prevent unauthorized removal of the computer or TOSHIBA Express Port Replicator. The computer has a security lock slot on the left side. Attach one end of a cable to a desk and the other end to the security lock slot.1. Turn the computer so the left side faces you.2. Align the holes for the security lock and attach the lock.Figure 3-22 Security lockSecurity lock slot
User’s Manual 3-38Features, Utilities and OptionsOptionsYou can add a number of options to make your computer even more powerful and convenient to use.You can buy the following options from TOSHIBA dealer.DDR2-533 Memory KitA 256, 512 or 1,024 MB memory module (DDR2-533) can easily be installed in the computer. DDR2-667 Memory KitA 256, 512, 1,024 or 2,048 MB memory module (DDR2-667) can easily be installed in the computer. USB FDD Kit The USB floppy disk drive accommodates either 3 1/2" 1.44-megabyte or 720-kilobyte floppy disks through connection to a USB port. Please note that you cannot format 720-kilobyte floppy disks under Windows XP, but you are able to use disks that have been previously formatted.Universal AC AdaptorIf you use your computer at more than one site frequently, it may be convenient to purchase an additional AC adaptor for each site so you will not have to carry the adaptor with you.Battery Pack An additional battery pack can be purchased from your TOSHIBA dealer. Use it as a spare or replacement.Slice Expansion BatteryThis battery pack increases your computer's operating time when a main battery pack is also installed. It is connectable to the Docking Port of the computer.Battery Charger The battery charger lets you charge extra batteries outside the computer.TOSHIBA Express Port ReplicatorThe TOSHIBA Express Port Replicator provides the ports available on the computer in addition to a digital visual interface (DVI) port*, External monitor port, four Universal Serial Bus ports (USB 2.0) and a LAN jack. *This computer is not supported.Tablet PC Pen Additional Tablet PC Pens can be purchased from your TOSHIBA dealer for use as spare items (spare pen tips and a tip draw-out tool are included).Reserve Pen Additional Reserve Pens can be purchased from your TOSHIBA dealer for use in the event the main pen becomes lost or damaged. The Reserve Pen is stored inside the computer.
User’s Manual 3-39Features, Utilities and OptionsBluetooth USB AdaptorWhen connected to one of the computer's USB ports, the Bluetooth USB adaptor allows wireless communications to be carried out with Bluetooth-compatible equipment.Wireless Optical Mouse with Bluetooth TechnologyThe Bluetooth Wireless Mouse is an optical mouse that is compatible with the Bluetooth wireless standard. Wireless Stereo Headset with Bluetooth TechnologyThe Bluetooth Wireless Stereo Headset provides stereo headphones that are compatible with the Bluetooth wireless standard.
User’s Manual 4-1Chapter 4Operating BasicsThis chapter describes the basic operations of your computer and precautions when using it, as well as the handling of CD/DVD.Using the Touch PadTo use the Touch Pad, simply touch and move your fingertip across it in the direction you want the on-screen pointer to go.Figure 4-1 Touch Pad and Touch Pad control buttonsTwo buttons below the Touch Pad are used like the buttons on a mouse pointer. Press the left button to select a menu item or to manipulate text or graphics designated by the pointer. Press the right button to display a menu or other function depending on the software you are using.Touch PadTouch Pad control buttons
User’s Manual 4-2Operating BasicsUsing the Tablet PC Pen and Reserve PenYou can use the Tablet PC Pen to execute actions and enter data. Hold the Tablet PC Pen in a natural position and tap, press or trace on the screen lightly. Before you begin using the your computer for the first time, you will need to calibrate the Tablet PC Pen. Refer to the Pointing device section in Chapter 8, Troubleshooting.Some computers in this series are equipped with a Reserve Pen.Figure 4-2 The Tablet PC Pen (left) and Reserve Pen (right)You can also tap the Touch Pad to perform functions similar to those of the left button.Click: Tap onceDouble-click: Tap twiceDrag and drop: Tap to select the material you want to move. Leave your finger on the Touch Pad after the second tap and move the material.Eraser button You can use this button as an eraser when using a graphics software application. Text based software application enable you to select and delete characters with a one-touch action.Pen button Provides the some function as clicking the right Touch Pad control button.Pen point Provides the some function as clicking the left Touch Pad control button.Eraser buttonPen buttonPen pointPen buttonPen point
User’s Manual 4-3Operating BasicsObserve the following precautions on the handling of the Tablet PC Pen.■Do not tap or press the Tablet PC Pen forcefully against the display as this could damage the Tablet PC Pen and the screen itself.■Avoid using or keeping the Tablet PC Pen in areas where the temperature can change rapidly or in places, such as a car, where the Tablet PC Pen is exposed to direct sunlight. Store the Tablet PC Pen without any pressure being applied to the buttons as this may cause a malfunction or characteristic deterioration.■The Tablet PC Pen is composed of precision parts. Do not drop the Tablet PC Pen. Strong impact causes a malfunction or characteristic deterioration.■Do not apply excessive force to the Tablet PC Pen point and the side switch. Excessive force applied to these parts causes short life or characteristic deterioration (Allowable force to pen point, Eraser button, Pen button: less than 1 kg, for less than 30 seconds).■Avoid water entering the Tablet PC Pen or condensation forming within it as either condition will cause a malfunction.■Do not disassemble the Tablet PC Pen. It causes maladjustment or short life.■Do not stain the Tablet PC Pen with cosmetics or chemicals as this will cause a deterioration in appearance. Use a glass wiping cloth or dry cloth to clean the Tablet PC Pen. Do not use volatile liquids such as alcohol, thinner or petroleum benzine to clean the Tablet PC Pen.■Do not apply excessive force to the Tablet PC Pen point as a bent or deformed pen point will cause a malfunction.■Keep the small parts of the Tablet PC Pen, such as the pen point or the knob of the side switch, away from infants and small children to prevent them from swallowing them.■Do not use a ball point pen instead of the Tablet PC Pen delivered with the product.■Do not use a broken pen tip.■The lead cannot be replaced if it is worn (use the Reserve Pen only).TOSHIBA is not liable for any problems arising on the products due to the use of the Tablet PC Pen in an environment where the above conditions are not satisfied or because of its use by unspecified number of users.
User’s Manual 4-4Operating BasicsRemoving the Tablet PC PenRemove the Tablet PC Pen as described below.1. Gently push the Tablet PC Pen towards the middle of the computer. The pen will then protrude slightly from the side.Figure 4-3 Removing the Tablet PC Pen2. Pull the Tablet PC Pen to remove it from the Tablet PC Pen slot.Inserting the Tablet PC PenThe Tablet PC Pen is included in the accessory tray when purchased. Remove the Tablet PC Pen from the carton and install it to the computer as follows:1. The Tablet PC Pen and the Reserve Pen are different in shape.Figure 4-4 Inserting the Tablet PC PenPen actionsYou can use the Tablet PC Pen to enter data, start programs, move objects and execute other actions.Tablet PC PenTablet PC Pen slotThe Tablet PC Pen and the Reserve Pen are different in shape. Do not insert the Reserve Pen into the Tablet PC Pen slot.Tablet PC Pen slot Tablet PC Pen
User’s Manual 4-5Operating BasicsSingle tapLightly tap the tip of the Tablet PC Pen on an object and lift it immediately to execute an action. A single tap is similar to clicking the left touch pad control button.Double tapLightly tap the tip of the Tablet PC Pen twice on an object and lift it immediately to execute an action. A double-tap is similar to double-clicking the left touch pad control button.Press and holdTouch the tip of the Tablet PC Pen to the display screen and hold it there to display a pop-up menu or other action. Press and hold is similar to clicking the right touch pad control button.DragTouch the Tablet PC Pen to the screen. Without lifting the Tablet PC Pen, drag it across the screen to select text or objects.Drag and dropTouch the Tablet PC Pen to the screen to select an object. Without lifting the Tablet PC Pen, drag it across the screen. Lift the Tablet PC Pen to drop the object to a new location.Replacing the pen tip1. To replace the pen tip, pinch the tip with a draw-out tool and pull it out.Figure 4-5 Replacing the pen tip2. Insert a new tip into the Tablet PC Pen, flat end first, and press it to seat it securely.Draw-out toolPen tip■A short and worn pen point is difficult to pull out. Replace the pen point with a refill before it becomes too short to remove.■It is recommended that you keep another pen set as a spare. You can buy replacement pen sets from your TOSHIBA authorized dealer.
User’s Manual 4-6Operating BasicsRemoving the Reserve PenTo remove the Reserve Pen case, follow the steps below.1. Save your work.2. Turn the computer’s power off. Make sure the Power indicator is off.3. Remove all cables connected to the computer.4. Close the LCD display panel and turn the computer upside down.5. Remove the battery pack.6. Remove the Reserve Pen from the pen holder.Figure 4-6 Removing the Reserve Pen7. Reinstall the battery pack.Inserting the Reserve Pen1. Remove the battery pack.2. Gently push the Reserve Pen into the pen holder to insert it.Figure 4-7 Inserting the Reserve PenDo not continue to use a broken pen tip as this may result in scratching of the LCD display panel. When the pen tip breaks replace it with one of the refills delivered with the Tablet PC Pen. When these refills have run out, you can purchase a new pen set from a TOSHIBA authorized dealer.Reserve PenRefer to the Replacing the battery pack section in Chapter 6, Power and Power-Up Modes for more information on how to remove and reinstall the battery pack.Pen holderReserve Pen
User’s Manual 4-7Operating Basics3. Reinstall the battery pack.Changing to the Tablet modeTo change from laptop mode to the Tablet mode, follow the instructions below.Figure 4-8 Changing to the Tablet mode (1)Refer to the Replacing the battery pack section in Chapter 6, Power and Power-Up Modes for more information on how to remove and reinstall the battery pack.■Place the computer on a stable, flat surface such as a desktop and rotate the LCD display panel slowly, holding the panel at its lower part. The LCD display panel is designed not to rotate more than 180 degrees. Rotating the LCD display panel more than 180 degrees with an excessive force will damage the panel and the computer.■To change from Laptop Mode to Tablet Mode you must rotate the display panel 180 degrees clockwise.Tablet mode icon Turn the LCD display panel to the direction indicated by the Tablet mode icon.To change from Tablet Mode to Laptop Mode you must rotate the display panel 180 degrees counter-clockwise.Laptop mode icon Turn the LCD display panel to the direction indicated by the laptop mode icon.
User’s Manual 4-8Operating Basics1. Open the LCD display panel to the upright position. Check that the angle of the keyboard and the LCD display panel is 90 degrees.2. Rotate the LCD display panel clockwise slowly.Figure 4-9 Changing to the Tablet mode (2)3. Turn the display latch 180 degrees to its down position.4. Close the LCD display panel slowly with display surface facing upwards.Figure 4-10 Changing to the Tablet mode (3)5. Insert the display latch in the slit.■When rotating LCD screen of your computer, be sure to slowly turn the screen in the proper direction, and not apply excessive force or speed.■Do not attempt to rotate the LCD display panel past the maximum rotation point. Forcing the LCD display panel past the maximum rotation point will damage the LCD display panel.Display latch
User’s Manual 4-9Operating Basics6. Press the LCD display panel downward softly.Figure 4-11 Changing to the Tablet mode (4)Changing the screen orientationThe orientation of the computer screen can be changed to one of the following four display modes:Figure 4-12 Four display modesDisplay latchSlitSecondary portraitPrimary portraitSecondary landscapePrimary landscape
User’s Manual 4-10Operating BasicsMethod 1: Changing the screen orientation using TOSHIBA Accelerometer Utilities and TOSHIBA Rotation UtilityWhen the TOSHIBA Accelerometer Utilities and TOSHIBA Rotation Utility are running, changes in the orientation of the top and bottom of the screen is automatically recognized by pressing ESC/Rotation button for more than a second.Method 2: Changing the screen orientation using Cross Function Button1. Press the Cross Function Button for more than one second. The TOSHIBA Tablet Menu will appear.2. Select the Internal Monitor icon in Toshiba Shortcut using the Cross Function Button and then press then Cross Function Button.3. Select the rotation angle using Cross Function Button and then press the Cross Function Button.■Execute the following applications on Primary landscape:■3D game software■3D screen saver■Playback of a motion picture as would be the case using DVD-Video playback on the computer connected to an external DVD-ROM Drive.■The screen cannot automatically rotate in the following cases. You should first quit the running application and then rotate the screen:■Running of an application that changes the screen resolution dynamically, such as a game that is running in full-screen mode.■DOS prompt in full-screen mode.■Running of 3D screen saver.■Do not play 3D game software or replay DVD-Video in a display mode other than Primary landscape. An abnormality will appear on the Windows screen display when you replay a DVD-Video in a mode other than Primary landscape because DVD playback software can boot only in the Primary landscape mode.■An abnormality will appear on the Windows screen display when you change from Tablet Mode to Laptop Mode while a 3D screen saver is running. In this case, press any key while in Laptop Mode to deactivate the 3D screen saver.
User’s Manual 4-11Operating BasicsMethod 3: Changing the screen orientation using Task Bar1. Right click "Change tablet and pen settings" icon in the Task Bar. Click "Change screen orientation" from the menu.The screen orientation is set to change in the following order when purchased.You can change the above sequence through the following procedure:1. Double click Change tablet and pen settings icon in the Task Bar.2. Click Change button in Display tab.3. Select "changing the screen" from the Screen Orientation pull down menu and change the screen.Using Accelerometer UtilitiesYou can set the orientation of the desktop screen just after rotating the display from [Start]-[All Programs]-[TOSHIBA]-[Tablet PC]-[TOSHIBA Rotation Utility].When you shake the computer:■Do not shake the computer too strongly as this may cause the computer to be dropped or hit those people or items around you.■Avoid using the computer in crowded places (e.g. in commuter trains or in busy streets).■This may cause injury to children or adults, or damage to the computer.When the TOSHIBA HDD protection function is turned on and the Tilt function (function to start applications, etc. by waving the computer vertically or horizontally) is used, the TOSHIBA HDD protection message may be displayed on the screen. Turn off the TOSHIBA HDD protection function in order to stop such messages from displaying.
User’s Manual 4-12Operating BasicsIt is safer if you hold the computer with both hands horizontally as shown in the below example.Figure 4-13 Shake the computerChanging to the laptop modeTo change the operating mode to the Laptop Mode, follow the instructions below.1. Press the Display latch and raise the display to the upright position carefully.2. Rotate the display counter-clockwise slowly.3. Turn the display latch toward you ready for the next closing of the display.Using the Fingerprint SensorThis product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints. By enrolling the ID and password onto the fingerprint authentication feature, it is no longer necessary to input the password from the keyboard. Fingerprint feature enables you to:■Logon to Windows and access a security-enabled homepage through IE (Internet Explorer).■Files and folders can be encrypted/decrypted and third party access to them prevented.■Disable the password-protected screen-saver when returning from power-saving (e.g., standby) mode.■Authentication of the User Password (and, if applicable, the HDD(Hard Disk Drive) Password) when booting up the computer (Power-on Security).■Single Sign-on featureThe computer is shaken perpendicularly.The computer is shaken horizontally.
User’s Manual 4-13Operating BasicsHow to Swipe the FingerUsing the following steps when swiping fingers for fingerprint registration or authentication will help to minimize authentication failures:Align the first joint of the finger to the center of the sensor. Lightly touch the sensor and swipe finger levelly towards you when in portrait mode, and sideways when in either landscape mode or Laptop mode.While lightly touching the sensor, swipe the finger towards you when in portrait mode, and sideways when in either landscape mode or Laptop mode until the sensor surface becomes visible.The following illustrations show the recommended way to swipe your finger over the fingerprint sensor.Figure 4-14 Swipe the finger■Avoid swiping with the finger stiff or pressed-on too hardFingerprint reading may fail if the center of the fingerprint is not touching on the sensor, or when finger is swiped while pressing hard. Make sure that the center of the fingerprint is touching the sensor before swiping.■Always confirm the center of the fingerprint whirl so that it is swiped along the centerline of the sensor.■When fingerprint reading is not successfulThere is a possibility of authentication failures if the finger is swiped too quickly or too slowly. Follow the onscreen instructions to adjust the speed of the swipe.
User’s Manual 4-14Operating BasicsPoints to note about the Fingerprint SensorFailure to follow these guidelines might result in (1) damage to the sensor or cause sensor failure, (2) finger recognition problems, or lower finger recognition success rate.■Do not scratch or poke the sensor with your nails or any hard or sharp objects.■Do not press the sensor strongly.■Do not touch the sensor with a wet finger or any wet objects. Keep sensor surface dry and free of water vapor.■Do not touch the sensor with a soiled finger. Minute foreign particles on a soiled or dirty finger may scratch the sensor.■Do not paste stickers or write on the sensor.■Do not touch the sensor with a finger or any object that has a build-up of static electricity on it.Observe the following before you place your finger on the sensor whether for fingerprint enrollment/registration or recognition.■Wash and dry your hands thoroughly.■Remove static electricity from your fingers by touching any metal surface. Static electricity is a common cause of sensor failures, especially when the weather is dry.■Clean the sensor with a lint-free cloth. Do not use detergent to clean the sensor.■Avoid the following finger conditions for enrollment or recognition as they may result in fingerprint enrollment errors or a drop in the fingerprint recognition success rate■Soaked or swollen finger (e.g. after taking bath)■Injured finger■Wet finger■Soiled or oily finger■Extremely dry skin condition on fingerObserve the following to improve the fingerprint recognition success rate.■Enroll two or more fingers.■Enroll additional fingers if recognition failure occurs often using enrolled fingers. ■Check your finger condition. Changed conditions, such as injured, rough, extremely dry, wet, soiled, dirty, oily, soaked, swollen fingers, may lower the recognition success rate. Also if the fingerprint is worn down or the finger becomes thinner or fatter, the recognition success rate may be lowered.■The fingerprint for each finger is different and unique. Please ensure that only the registered or enrolled fingerprint or fingerprints are used for identification.■Check sliding position and speed (see the drawing and information on the following pages).
User’s Manual 4-15Operating BasicsHow to Delete the Fingerprint DataSaved fingerprint data is stored in non-volatile memory inside the fingerprint sensor. If you hand over the computer to others, or dispose of it, it is recommended that you perform the following operations.1. Click start, point to All Programs, point to Protector Suite QL and click Control Center.2. The Protector Suite Software screen is displayed. 3. Click Fingerprints and click Delete.4. Click Settings and click Fingerprint Storage Inspector.5. The Fingerprint Storage Inspector screen is displayed. If other fingerprint data is still displayed on the list, select all fingerprint data and click Remove.6. Check whether all fingerprint data was deleted on the fingerprintStorage inspector screen.Fingerprint Sensor Limitations■The fingerprint sensor compares and analyzes the unique characteristics in a fingerprint.■A warning message will be displayed when recognition is abnormal or recognition is not successful within a fixed duration.■The recognition success rate may differ from user to user.■Toshiba does not guarantee that this fingerprint recognition technology will be error-free.■Toshiba does not guarantee that the fingerprint sensor will recognize the enrolled user or accurately screen out unauthorized users at all times. Toshiba is not liable for any failure or damage that might arise out of the use of this fingerprint recognition software or utility.Points to note about the Fingerprint UtilityIf Windows XP’s file encryption function EFS (Encryption File System) is used to encrypt a file, the file cannot be further encrypted using the encryption function of this software. If the fingerprint sensor and Trusted Platform Module (TPM) security are used as identification devices, install and configure the Infineon TPM Professional package first before configuring the fingerprint utility. Please refer to the TPM (Trusted Platform Module) Installation Guide for the installation and configuration methods for TPM.Backups for saved fingerprint data and saved information in the PasswordBank can be performed in Import or Export User Data under Fingerprint Software Management. However, encrypted files cannot be backed within Mysafe using this function. Instead it is recommended that you backup encrypted files to external media using standard methods such as the file copy process within Windows XP.
User’s Manual 4-16Operating BasicsIn the help file, it is stated that this software's PasswordBank function can be used for the Internet and general applications. However, the Internet PasswordBank function in the fingerprint utility provided in this computer can only be used with IE (Internet Explorer).Set Up ProcedurePlease use the following procedure when first using fingerprint authentication.Fingerprint RegistrationEnroll the required authentication data using the "User Enrollment" Wizard.1. Click start, point to All Programs, point to Protector Suite QL and click User Enrollment Wizard.2. Click Next.3. The User’s Password screen is displayed. Ensure the same Windows logon username is displayed before entering a password into the Enteryour password field. Click Next.4. The Hints for Fingerprint Enrollment screen is displayed.Confirm the message and that there is a checkmark in Run Interactive Tutorial, and click Next.5. The Correct Swipe Procedure screen is displayed. Confirm the message and click Next.6. The Scanning Practice screen is displayed.You can practice swiping your finger and when you have finished practicing swiping your finger, click Next.7. The User’s Fingers screen is displayed. Based on the illustration, select the finger to be recognized, and then click Next. Previously enrolled fingerprints would have green check marks. The fingerprint being enrolled now would have a red check mark. If any of the previously enrolled fingerprints is selected again, the latest information will be enrolled and previous information over-written. 8. The Advanced Security screen is displayed.Select whether to enable the security function, and click Next.9. The Finalization screen is displayed. Click Finish. This completes the fingerprint registration process.■The fingerprint authentication uses the same Windows logon ID and password. If the Windows logon password has not been setup, please do so before registration.■Up to 21 fingerprint patterns can be registered on this sensor.You can also start User Enrollment Wizard using the following method. ■Click the Protector Suite QL icon in the Task Bar.■Swipe your finger across the Fingerprint Sensor.
User’s Manual 4-17Operating BasicsWindow Logon via Fingerprint AuthenticationIn place of the usual Windows logon by ID and password, fingerprint authentication also allows logon to Windows. This is useful especially when many users are using the same computer as it allows the user selection screen to be skipped.Fingerprint Authentication Procedure1. Start up the computer.2. The Logon Authorization screen is displayed. Choose any of the enrolled fingers and swipe the fingerprint on the sensor. If authentication is successful, the user will be logged on to Windows.Fingerprint Power-on Security GeneralThe fingerprint authentication system can be used to replace the keyboard-based User/BIOS Password authentication system when booting up.If you do not want to use the fingerprint authentication system for password authentication when booting up, but prefer to use the keyboard-based system instead, press the BkSP (backspace) key or the ESC/Rotation button when the Fingerprint Power-on Security screen is displayed. This will switch the password input screen to the keyboard-based one.If the fingerprint authentication fails, please logon using the Windows logon password. Please logon using the Windows logon password if the fingerprint authentication failed for three consecutive tries. To logon using the Windows logon password, enter the Windows logon password at the "Welcome" screen as normal.A warning message will be displayed when authentication is abnormal or authentication is not successful within a fixed duration.■It is necessary to register the User Password before using the Fingerprint Power-on Security and its extended function, the Fingerprint Single Sign-on Feature. Please use TOSHIBA Password Utility to register the User Password.■If you fail fingerprint authentication more than five times, you must enter the User Password or Supervisor Password manually to start the computer.■When swiping, please do it slowly and at a constant speed. If this does not improve the authentication rate, please adjust the speed.■If there are any changes in the environment or settings related to authorization, you will be required to provide authorization information such as a User Password (and, if applicable, the HDD(Hard Disk Drive) password).
User’s Manual 4-18Operating BasicsHow to Enable Fingerprint Power-on Security SettingsIt is necessary to first enroll your fingerprint with the Protector Suite QL application prior to enabling and configuring the Fingerprint Power-on Security System. Check that your fingerprint is enrolled before configuring the settings. Refer to the Manual for Fingerprint Registration/Enrollment instructions.1. Swipe your finger across the Fingerprint Sensor.2. MENU appears in the lower right corner of the screen. Swipe (*) your finger on the Fingerprint Sensor, and select Control Center from the MENU items. (*). It is recommended that the keyboard cursor keys (movement) and enter key (selection) or the directional pad be used when selecting an Item from the Menu in laptop or landscape modes.3. The Fingerprint Software Management screen is displayed. Click Settings and click Power-on Security.4. The Power-on Security screen is displayed. Place a checkmark in Replace the power-on and hard drive passwords with the fingerprint reader and click OK.Fingerprint Single Sign-on FeatureGeneralThis is a feature that allows the user to complete the authentication for both the User/BIOS Password (and, if applicable, the HDD(Hard Disk Drive) Password) and logging onto Windows using only one fingerprint authentication when booting up. It is necessary to register the User/BIOS Password and Windows Logon Password before using the Fingerprint Power-on Security and this Fingerprint Single Sign-on Feature. Please use the TOSHIBA Password Utility to register your User/BIOS Password. If Windows Logon is not the default for your system, see Manual to register your Windows Logon Password. Only one fingerprint authentication is required to replace the User/BIOS Password (and, if applicable, the HDD(Hard Disk Drive) Password) and the Windows Logon Password.How to Enable Fingerprint Single Sign-on FeatureIt is necessary to first enroll your fingerprint with the Protector Suite QL application prior to enabling and configuring the How to Enable Fingerprint Single Sign-on Feature. Check that the fingerprint is enrolled before configuring the settings. Refer to the Manual for Fingerprint Registration/Enrollment instructions.1. Swipe your finger across the Fingerprint Sensor.2. MENU appears in the lower right corner of the screen. Swipe (*) your finger on the Fingerprint Sensor, and select Control Center from the MENU items.
User’s Manual 4-19Operating Basics(*). It is recommended that the keyboard cursor keys (movement) and enter key (selection) or the directional pad be used when selecting an Item from the Menu in laptop or landscape modes.3. The Fingerprint Software Management screen is displayed. Click Settings and click System Settings.4. The Protector Suite Settings screen is displayed. Place a checkmark in Allow power-on security single sign-on within Enable logon support and click OK.Fingerprint utility limitationsTOSHIBA does not guarantee that the Fingerprint utility technology will be completely secure or error-free. TOSHIBA does not guarantee that the Fingerprint utility will accurately screen out unauthorized users at all times. TOSHIBA is not liable for any failure or damage that might arise out of the use of the fingerprint software or utility.Using optical disc drivesThe full-size drive provides high-performance execution of CD/DVD-ROM-based programs. You can run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without an adaptor. An ATAPI interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD-ROM, an indicator on the drive glows.If you have a DVD-ROM&CD-R/RW drive, refer also to the Writing CDs on DVD-ROM&CD-R/RW drive section for precautions on writing to CDs.If you have a DVD Super Multi drive, refer also to the Writing CD/DVDs on DVD Super Multi drive section for precautions on writing to CDs/DVDs.Loading discsTo load CD/DVDs, follow the steps below.1. When the computer’s power is on, press the eject button to openthe disc tray slightly.Use the WinDVD application to view DVD-Video discs.When the power of the optical disc drive is off, pressing the Fn +Tab keys will turn the power of the optical disc drive on. Furthermore, it is possible to set it to turn the power of the optical disc drive on and eject the tray at the same time.
User’s Manual 4-20Operating Basics2. Grasp the disc tray gently and pull until it is fully opened.Figure 4-15 Pressing the eject button and pulling the disc tray open3. Lay the CD/DVD, label side up, in the disc tray. Figure 4-16 Inserting a CD/DVDDisc trayLaser lensWhen the disc tray is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the disc tray. After seating the CD/DVD, however, make sure it lies flat.■Do not touch the laser lens or any portion of its surrounding casing as this could cause misalignment.■Prevent foreign objects from entering the drive. Check the surface of the disc tray, especially the area behind the front edge of the disc tray, to make sure there are no such objects before closing the drive.
User’s Manual 4-21Operating Basics4. Press gently at the center of the CD/DVD until you feel it click into place. The CD/DVD should lie below the top of the spindle, flush with the spindle base.5. Push the center of the disc tray to close it. Press gently until it locks into place. Figure 4-17 Closing the CD/DVD disc trayRemoving discsTo remove the CD/DVD, follow the steps below.1. To pop the disc tray partially open, press the eject button. Gently pull the disc tray out until it is fully opened.If the CD/DVD is not seated properly when the disc tray is closed, the CD/DVD might be damaged. Also, the disc tray might not open fully when you press the eject button.Do not press the eject button while the computer is accessing the media drive. Wait for the optical disc drive indicator to go out before you open the disc tray. Also, if the CD/DVD is spinning when you open the disc tray, wait for it to stop before you remove it.When the disc tray pops open slightly, wait a moment to make sure the CD/DVD has stopped spinning before pulling the disc tray fully open.
User’s Manual 4-22Operating Basics2. The CD/DVD extends slightly over the sides of the disc tray so you can grasp it. Gently lift out the CD/DVD.Figure 4-18 Removing a CD/DVD3. Push the center of the disc tray to close it. Press gently until it locks into place.How to remove CD/DVD when the disc tray will not openPressing the eject button will not open the disc tray when the computer power is off. If the power is off, you can open the disc tray by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole near the eject button.Figure 4-19 Manual release with the eject hole15mmEject holeTurn off the power before you use the eject hole. If the CD/DVD is spinning when you open the disc tray, the CD/DVD could fly off the spindle and cause injury.
User’s Manual 4-23Operating BasicsWriting CDs on DVD-ROM&CD-R/RW driveDepending on the type of drive installed, you may be able to write CDs. The DVD-ROM&CD-R/RW drive lets you write as well as read CD-ROMs. Observe the precautions in this section to ensure the best performance for writing CDs. For information on loading and unloading CDs refer to the Using optical disc drives section.Before writing or rewritingPlease observe the following points when you write or rewrite the data.■We recommend the following manufacturers of CD-R and CD-RW media. Media quality can affect write or rewrite success rates.■Refer to the Writable discs, Chapter 2 for the details about the types of writable CD/DVD discs.■Do not turn off the power of the optical disc drive while the computer is accessing the drive. If you turn off the power, you may lose data.■When the power of the optical disc drive is off, the disc tray will not open even if the eject button is pushed. Use the Optical Drive Power to turn the power of the optical disc drive on. Refer to Chapter 3, Special features.When writing to media using an optical drive, always connect the AC adaptor to a power plug socket or power source to ensure maximum performance. If data is written powered by the batteries, writing may sometimes fail due to low battery power and data loss may occur.CD-R:TAIYO YUDEN CO., LTD.MITSUBISHI CHEMICAL CORPORATIONRICOH Co., Ltd.Multi-Speed and High-Speed CD-RW:MITSUBISHI CHEMICAL CORPORATIONRICOH Co., Ltd.Ultra-Speed CD-RW:MITSUBISHI CHEMICAL CORPORATION
User’s Manual 4-24Operating BasicsTOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above. Operation of other media cannot be guaranteed.■The actual number of rewrites to CD-RW media is affected by the quality of the disc and the way it is used. ■Be sure to connect the AC adaptor when you write or rewrite.■Be sure to close all other software programs except the writing software.■Do not run software such as a screen saver which can put a heavy load on the CPU.■Operate the computer at full power. Do not use power-saving features.■Do not write while virus check software is running. Wait for it to finish, then disable virus detection programs including any software that checks files automatically in the background.■Do not use hard disk utilities, including those intended to enhance hard disk drive access speeds. They may cause unstable operation and damage data.■Write from the computer's hard disk drive to the CD. Do not try to write from shared devices such as a LAN server or any other network device.■Writing with software other than Sonic RecordNow! has not been confirmed. Therefore, operation with other software cannot be guaranteed.When writing or rewritingNote the following when you write or rewrite a CD-R or CD-RW.■Always copy data from the hard disk drive to the optical disc. Do not use cut-and-paste as the original data will be lost if there is a write error.■Do not perform any of the following actions:■Change users in the Windows XP operating system.■Operate the computer for any other function, including use of a mouse or Touch Pad, closing/opening the LCD panel.■Start a communication application such as a modem.■Apply impact or vibration to the computer.■Install, remove or connect external devices, including the following:PC card, SD card, Memory Stick/Memory Stick Pro, xD picture card, MultiMediaCard, USB devices, external monitor, i.LINK devices and optical digital devices.■Open the optical disc drive.■If the media is poor in quality, dirty or damaged, writing or rewriting errors may occur.■Set the computer on a level surface and avoid places subject to vibration such as airplanes, trains or cars. Do not use an unstable surface such as a stand.■Keep mobile phones and other wireless communication devices away from the computer.
User’s Manual 4-25Operating BasicsWriting CD/DVDs on DVD Super Multi driveYou can use the DVD Super Multi drive to write data to either CD-R/RW or DVD-R/-R DL/-RW/+R/+R DL/+RW/-RAM discs. The following applicationsfor writing are provided: RecordNow!, and DLA licensed by Sonic Solutions.Important messageBefore you write or rewrite to CD-R/RW or DVD-R/-R DL/-RW/+R/+R DL/+RW/-RAM discs, read and follow all setup and operating instructions in this section. If you fail to do so, the DVD Super Multi drive may not function properly, and you may fail to write or rewrite, lose data or incur other damage.DisclaimerTOSHIBA does not bear responsibility for the following:■Damage to any CD-R/RW or DVD-R/-R DL/-RW/+R/+R DL/+RW/-RAM disc that may be caused by writing or rewriting with this product.■Any change or loss of the recorded contents of CD-R/RW or DVD-R/-R DL/-RW/+R/+R DL/+RW/-RAM disc that may be caused by writing or rewriting with this product, or for any business profit loss or business interruption that may be caused by the change or loss of the recorded contents.■Damage that may be caused by using third party equipment or software.Given the technological limitations of current optical disc writing drives, you may experience unexpected writing or rewriting errors due to disc quality or problems with hardware devices. Also, it is a good idea to make two or more copies of important data, in case of undesired change or loss of the recorded contents.■Refer to the Writable discs, Chapter 2 for the details about the types of writable CD/DVD discs.■Do not turn off the power of the while the computer is accessing the drive. If you turn off the power, you may lose data.■When the power of the optical disc drive is off, the disc tray will not open even if the eject button is pushed. Use the Optical Drive Power icon to turn the power to the drive on. Refer to Chapter 3, Special features.When writing to media using an optical drive, always connect the AC adaptor to a power plug socket or power source to ensure maximum performance. If data is written powered by the batteries, writing may sometimes fail due to low battery power and data loss may occur.
User’s Manual 4-26Operating BasicsBefore writing or rewriting■Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/-R DL/+R/+R DL/-RW/+RW/-RAM disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates.CD-R:TAIYO YUDEN CO., LTD.MITSUBISHI CHEMICAL CORPORATIONRICOH Co., Ltd.CD-RW: (Multi-Speed and High-Speed)MITSUBISHI CHEMICAL CORPORATIONRICOH Co., Ltd.CD-RW: (Ultra-Speed)MITSUBISHI CHEMICAL CORPORATIONDVD-R:DVD Specifications for Recordable Disc for General Version 2.0TAIYO YUDEN CO., LTD.Matsushita Electric Industrial Co., Ltd.DVD-R DL: (Dual Layer supported model only)MITSUBISHI CHEMICAL CORPORATIONDVD+R:MITSUBISHI CHEMICAL CORPORATIONRICOH Co., Ltd.DVD+R DL: (Double Layer supported model only)MITSUBISHI CHEMICAL CORPORATIONDVD-RW:DVD Specifications for Recordable Disc for Version 1.1 or version 1.2VICTOR COMPANY OF JAPAN.LIMITEDMITSUBISHI CHEMICAL CORPORATION
User’s Manual 4-27Operating Basics■If the disc is poor in quality, dirty or damaged, writing or rewriting errors may occur. Be careful to check the disc for dirt or damage before you use it.■The actual number of rewrites to CD-RW, DVD-RW, DVD+RW or DVD-RAM is affected by the quality of the disc and the way it is used.■There are two types of DVD-R discs: authoring and general use discs. Do not use authoring discs. Only general use discs can be written to by a computer drive.■You can use DVD-RAM discs that can be removed from a cartridge and DVD-RAM discs designed without a cartridge. ■Other DVD-ROM drives for computers or other DVD players may not be able to read DVD-R/-R DL/-RW or DVD+R/+R DL/+RW discs.■Data written to a CD-R/DVD-R/-R DL/DVD+R/+R DL disc cannot be deleted either in whole or in part.■Data deleted (erased) from a CD-RW, DVD-RW, DVD+RW and DVD-RAM disc cannot be recovered. Check the content of the disc carefully before you delete it. If multiple drives that can write data to discs are connected, be careful not to delete data from the wrong drive.■In writing to a DVD-R/-R DL/-RW, DVD+R/+R DL/+RW or DVD-RAM disc, some disc space is required for file management, so you may not be able to write the full capacity of the disc.■Since the disc is based on the DVD standard, it might be filled with dummy data if the written data is less than about 1 GB. Even if you write only a small amount of data, it might take time to fill in the dummy data.■DVD-RAM formatted by FAT32 cannot be read in Windows 2000 without DVD-RAM Driver Software.■When multiple drives that can write data to discs are connected, be careful not to write to the wrong drive.■Be sure to connect the AC adaptor before you write or rewrite.DVD+RW:MITSUBISHI CHEMICAL CORPORATIONRICOH Co., Ltd.DVD-RAM:DVD Specifications for DVD-RAM Disc for Version 2.0, Version 2.1 or Version 2.2Hitachi Maxell Ltd.■This drive cannot use discs that allow writing faster than 8 speed (DVD-R, DVD+R), 4 speed (DVD-RW, DVD+RW), 5 speed (DVD-RAM), 2.4 speed (DVD+R DL, Double Layer supported model only), 2 speed (DVD-R DL, Dual Layer supported model only).■2.6GB and 5.2GB DVD-RAM media cannot be read from or written to.■DISC created in DVD-R DL format4 (Layer Jump Recording) cannot be read.
User’s Manual 4-28Operating Basics■Before you enter standby/Hibernation Mode, be sure to finish DVD-RAM writing. Writing is finished if you can eject DVD-RAM media.■Be sure to close all other software programs except the writing software.■Do not run software such as a screen saver, which can put a heavy load on the CPU.■Operate the computer in full-power mode. Do not use power-saving features.■Do not write while virus check software is running. Wait for it to finish and then disable virus detection programs including any software that checks files automatically in the background.■Do not use hard disk utilities, including those intended to enhance hard disk drive access speed. They may cause unstable operation and data damage.■CD-RW (Ultra Speed +) media is not supported. If used, data may be lost or damaged.■Write from the computer’s hard disk drive to the CD/DVD. Do not try to write from shared devices such as a LAN server or any other network device.■Writing with software other than RecordNow! and DLA for TOSHIBA are not recommended.When writing or rewritingPlease observe/consider the following when you write or rewrite to a CD-R/RW, DVD-R/-R DL/-RW/-RAM or DVD+R/+R DL/+RW disc.■Do not perform any of the following actions when writing or rewriting:■Change users in the Windows XP operating system.■Operate the computer for any other function, including using a mouse or Touch Pad or closing/opening the LCD panel.■Start a communication application such as a modem.■Apply impact or vibration to the computer.■Install, remove or connect external devices, including the following:PC card, SD card, Memory Stick/Memory Stick Pro, xD picture card, MultiMediaCard, USB devices, external monitor, i.LINK devices and optical digital devices.■Use the Audio/Video control button to reproduce music or voice.■Open the optical disc drive.■Do not use shut down/log off and standby/hibernation while writing or rewriting.■Make sure writing or rewriting is completed before going into standby/hibernation. Writing is completed if you can open the DVD-ROM&CD-R/RW or DVD Super Multi drive tray.■Set the computer on a level surface and avoid places subject to vibration such as airplanes, trains, or cars. Do not use an unstable surface such as a stand.
User’s Manual 4-29Operating Basics■Keep mobile phones and other wireless communication devices away from the computer.■Always copy data from the hard disk drive to the optical disc. Do not use cut-and-paste. The original data will be lost if there is a write error.RecordNow! Basic for TOSHIBANote the following limitations when you use RecordNow!:■DVD-Video cannot be created using RecordNow!.■DVD-Audio cannot be created using RecordNow!.■You cannot use RecordNow!'s "Audio CD for Car or Home CD Player" function to record music to DVD-R/-R DL/-RW or DVD+R/+R DL/+RW discs.■Do not use the "Exact Copy" function of RecordNow! to copy DVD-Video and DVD-ROM with copyright protection.■DVD-RAM disc cannot be backed up with the "Exact Copy" function of RecordNow!.■You cannot back up a CD-ROM or CD-R/RW to DVD-R/-R DL/-RW or DVD+R/+R DL/+RW using the "Exact Copy" function of RecordNow!.■You cannot back up DVD-ROM, DVD-Video, DVD-R/-R DL/-RW or DVD+R/+R DL/+RW to CD-R/RW using the "Exact Copy" function of RecordNow!.■RecordNow! cannot record in packet format.■You might not be able to use the "Exact Copy" function of RecordNow! to back up a DVD-R/-R DL/-RW or DVD+R/+R DL/+RW disc that was made with other software on a different DVD-R/-R DL/-RW or DVD+R/+R DL/+RW recorder.■If you add data to a DVD-R and DVD+R disc that you have already recorded to, you might not be able to read the added data under some circumstances. It cannot be read in 16-bit operating systems, such as Windows 98SE and Windows Me. In Windows NT4, you will need Service Pack 6 or later to read added data while in Windows 2000, you will need Service Pack 2 or later to read it. Some DVD-ROM and DVD-ROM&CD-R/RW drives cannot read added data regardless of the operating system.■RecordNow! does not support recording to DVD-RAM discs. To record to a DVD-RAM disc, use Explorer or a similar utility.■When you back up a DVD disc, be sure the source drive supports recording to DVD-R/-R DL/-RW or DVD+R/+R DL/+RW discs. If the source drive does not support recording to DVD-R/-R DL/-RW or DVD+R/+R DL/+RW discs, it might not be backed up correctly. ■When you back up a DVD-R, DVD-RW, DVD+R or DVD+RW, be sure to use the same type of disc.■You cannot partially delete any data written to a CD-RW, DVD-RW or DVD+RW disc.Discs created in DVD-R DL format4 (Layer Jump Recording) cannot beread.
User’s Manual 4-30Operating BasicsData VerificationTo verify that data is written or rewritten correctly, follow the steps below before you write or rewrite a Data CD/DVD.1. Click the Options button ( ) on the RecordNow! Console to open the Options panels.2. Select Data from the left-hand menu.3. Mark the Verify data written to the disc after burning check box in the Data Options.4. Click the OK button.DLA for TOSHIBANote the following limitations when you use DLA:■This software supports only rewritable discs (DVD+RW, DVD-RW, and CD-RW). It does not support DVD+R/+R DL, DVD-R/-R DL, and CD-R discs that are not rewritable.■DLA does not support formatting and writing to a DVD-RAM disc - these functions are performed by DVD-RAM Driver Software. Even if the DLA Format menu appears when inserting a DVD-RAM disc and right-clicking the drive icon in Windows Explorer, you should use the "DVDForm" command to format this disc. You can run "DVDForm" by clicking the Start button on the taskbar to display the Start menu and then selecting "All Programs", "DVD-RAM", "DVD-RAM Driver" and "DVDForm" sequentially.■Do not use any discs that have been formatted with packet writing software other than DLA. Similarly, do not use any discs that have been formatted with DLA with any packet writing software other than DLA. When using a disc you are not familiar with, format it by selecting "Full Format" before using it.■Do not use the cut-and-paste function for files and folders. A file or folder that has been cut may be lost if writing fails due to an error on the disc.■When writing any setup files for an application to a disc formatted by DLA, and attempting to start Setup from this disc, an error may occur. In this case, please copy the files to your hard disk and then run Setup from there.
User’s Manual 4-31Operating BasicsMedia careThis section provides tips on protecting data stored on your CD/DVDs and floppy disks.Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them:CD/DVDs1. Store your CD/DVDs in the container they came in to protect them and keep them clean.2. Do not bend the CD/DVD.3. Do not write on, apply a sticker to, or otherwise mar the surface of the CD/DVD that contains data.4. Hold the CD/DVD by its outside edge or the edge on the center hole. Fingerprints on the surface can prevent the drive from properly reading data.5. Do not expose to direct sunlight, extreme heat or cold. Do not place heavy objects on your CD/DVDs.6. If your CD/DVDs become dusty or dirty, wipe them with a clean dry cloth. Wipe from the center out, do not wipe in a circular direction around the CD/DVD. If necessary, use a cloth dampened in water or a neutral cleaner. Do not use benzine, thinner or similar cleaner.Floppy disks1. Store your floppy disks in the container they came in to protect them and keep them clean. If a floppy disk is dirty, do not use cleaning fluid. Clean it with a soft damp cloth.2. Never open the shutter or touch the magnetic surface of your floppy disk. You could permanently damage it and lose data.3. Always handle floppy disks with care, to prevent the loss of stored data. Always apply the floppy disk label in the correct location. Never apply a new label on top of an existing one. The label could come loose and damage the floppy drive.4. Never use a pencil for writing on a floppy disk label. Pencil lead dust could cause a system malfunction. Always use a felt-tipped pen. When writing a title on a label, first write on the label, then apply the label to the floppy disk.5. Never put a floppy disk in a location where water or other liquid may contact it or where it is excessively damp. It could cause data loss. Never use a wet or damp floppy disk. It could damage the floppy disk drive or other devices.6. Data may be lost if the floppy disk is twisted; bent; or exposed to direct sunlight, extreme heat or cold.7. Do not place heavy objects on your floppy disks.8. Do not eat, smoke, or use erasers near your floppy disks. Foreign particles inside the floppy disk’s jacket can damage the magnetic surface.
User’s Manual 4-32Operating Basics9. Magnetic energy can destroy the data on your floppy disks. Keep your floppy disks away from speakers, radios, television sets and other sources of magnetic fields. Sound SystemThis section describes audio controls including sound levels.Volume ControlThe Volume Control utility lets you control the audio volume in Windows for both playback and recording.■To launch Volume Control for playback, click start, point to AllPrograms, point to Accessories, point to Entertainment and click Volume Control.■To launch Recording Control, click Options, point to Properties, select  Realtek HD Audio input and click OK.■To view details of the Volume Control, click Help on the Volume Control.Microphone levelThe change the microphone gain, follow the steps below.1. Click start, point to All Programs, point to Accessories, point to Entertainment and click Volume Control.2. Click Options and point to Properties.3. Select Mic Volume and click OK.4. Click Options and select Advanced Controls.5. Click Advanced.6. Check the Microphone Boost checkbox.TOSHIBA Mic EffectTOSHIBA Mic Effect provides you with a hands-free environment for holding mutual communication via the Internet Protocol or Local Area Network. If you wish to communicate with someone on your computer, you can use a messenger application. However, with such an application, you would hear your own voice returning to you as echo during the communication if you did not use a headset system or headphone. TOSHIBA Mic Effect will reduce these echoes generated on your computer.TOSHIBA Mic Effect also provides you the Microphone Array. The Microphone Array function eliminates sounds and noise originating outside the range by specifying the target range and direction of the microphone input.For more instructions for this software, click start, point to All Programs,point to TOSHIBA, point to Utilities and click TOSHIBA Mic Effect Help.
User’s Manual 4-33Operating BasicsModemThis section describes how to connect and disconnect the internal modem to and from a telephone jack.Click the icon with the secondary mouse button to display the properties menu on the screen.Region selectionTelecommunication regulations vary from one region to another, so you will need to make sure the internal modem’s settings are correct for the region in which it will be used.To select a region, follow the steps below.1. Click start, point to All Programs, point to TOSHIBA, point toNetworking and click Modem Region Select.2. The Region Selection icon will appear in the Windows Task Bar.3. Click the icon with the primary mouse button to display a list of regions that the modem supports. A sub menu for telephony location information will also be displayed. A check will appear next to the currently selected region and telephony location.4. Select a region from the region menu or a telephony location from the sub-menu. ■When you click a region it becomes the modem’s region selection, and the New Location for telephony will be set automatically.■Connection to any communication line other than an analog phone line could cause a PC system failure.■Connect the built-in modem only to ordinary analog phone lines.■Never connect the built-in modem to a digital line (ISDN).■Never connect the built-in modem to the digital connector on a public telephone or to a digital private branch exchange (PBX).■Never connect the built-in modem to a key telephone system for residences or offices. ■Never operate your PC on AC power during a thunderstorm. If you see lightning or hear thunder, immediately turn off the PC. An electric surge caused by the storm, may result in a system failure, loss of data or hardware damage.The built-in modem can be used only in specified countries and regions. Using the modem in an area not specified for use may cause a system failure. Check the specified areas carefully before using it.Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available. If you change the Country/Region in the Control Panel, the change may not take effect.
User’s Manual 4-34Operating Basics■When you select a telephony location, the corresponding region is automatically selected and it becomes the modem’s current region setting.Properties menuClick the icon with the secondary mouse button to display properties menu on the screen.SettingYou can enable or disable the following settings:AutoRun ModeThe Region Select utility starts automatically when you start up the operating system.Open the Dialing Properties dialog box after selecting region.The dialing properties dialog box will be displayed automatically after you select the region.Location list for region selection.A submenu appears displaying location information for telephony.Open dialog box, if the modem and Telephony Current Location region code do not match.A warning dialog box is displayed if current settings for region code and telephony location are incorrect.Modem SelectionIf the computer cannot recognize the internal modem, a dialog box is displayed. Select the COM port for your modem to use.Dialing PropertiesSelect this item to display the dialing properties.If you are using the computer in Japan, the Telecommunications Business Law requires that you select Japan region mode. It is illegal to use the modem in Japan with any other selection.
User’s Manual 4-35Operating BasicsConnectingTo connect the modular cable, follow the steps below. 1. Plug one end of the modular cable into the computer’s modem jack.2. Plug the other end of the modular cable into a telephone jack.Figure 4-20 Connecting the internal modemThe modular cable that comes with the computer must be used to connect the modem. Connect the end of the modular cable with the core to the computer. ■Connection to any communication line other than an analog phone line could cause a PC system failure.■Connect the built-in modem only to ordinary analog phone lines.■Never connect the built-in modem to a digital line (ISDN).■Never connect the built-in modem to the digital connector on a public telephone or to a digital private branch exchange (PBX).■Never connect the built-in modem to a key telephone system for residences or offices. ■Never operate your PC on AC power during a thunderstorm. If you see lightning or hear thunder, immediately turn off the PC. An electric surge caused by the storm, may result in a system failure, loss of data or hardware damage.Modular cableModem jackTelephone jackDo not pull on the cable or move the computer while the cable is connected.
User’s Manual 4-36Operating BasicsDisconnectingTo disconnect the internal modular cable, follow the steps below.1. Pinch the lever on the connector in the telephone jack and pull out the connector.2. Disconnect the cable from the computer’s modem jack in the same manner.Wireless communicationsThe computer’s wireless communication function supports both Wireless LAN and Bluetooth devices.All models are provided with a Wireless communication switch. Some models are equipped with both Wireless LAN and Bluetooth functions.Wireless LANThe Wireless LAN is compatible with other LAN systems based on Direct Sequence Spread Spectrum / Orthogonal Frequency Division Multiplexing radio technology that complies with the IEEE802.11 Wireless LAN standard (Revision A, B or G).■Theoretical maximum speed: 54Mbps (IEEE802.11a, 802.11g)■Theoretical maximum speed: 11Mbps (IEEE802.11b)■Frequency Channel Selection (Revision A: 5 GHz, Revision B/G: 2.4 GHz)■Roaming over multiple channels■Card Power Management■Wired Equivalent Privacy (WEP) data encryption, based on 152 bit encryption algorithm (Atheros module type).If you use a storage device such as an optical drive or hard disk drive connected to a 16-bit PC card, you might experience the following modem problems:■Modem speed is slow or communication is interrupted.■Skips may occur in sound.Do not install or remove an optional memory module while Wake-up on Wireless LAN is enabled.■The Wake-up on Wireless LAN function consumes power even when the system is off. Leave the AC adaptor connected while using this feature.■The Wake-up on Wireless LAN function is effective only when it is connected with an Access Point. This function becomes invalid when the connection is broken.
User’s Manual 4-37Operating Basics■Wired Equivalent Privacy (WEP) data encryption, based on 128 bit encryption algorithm (Intel module type).■Wi-Fi Protected Access (WPA).■Advanced Encryption Standard (AES) data encryption.■Wake-up on Wireless LAN (Intel module type).Setting1. Please make sure that the Wireless Communication Switch is turned on.2. Click start and select Connect to -> Wireless Network Connection.3. Select Set up a wireless network for a home or small office.4. Follow the wizard. You will need the name of the wireless network together with security settings. Consult the documentation accompanied with your router or ask your wireless network administrator for the settings.Security■TOSHIBA strongly recommend that you enable WEP (encryption) functionality, otherwise your computer will be open to illegal access by an outsider using a wireless connection. If this occurs, the outsider may illegally access your system, eavesdrop, or cause the loss or destruction of stored data.■TOSHIBA is not liable for the loss of data due to eavesdropping or illegal access through the wireless LAN and the damage thereof.Bluetooth wireless technologyBluetooth® wireless technology eliminates the need for cables between electronic devices such as desktop computers, printers and mobile phones. You cannot use the built-in Bluetooth functions and an optional Bluetooth SD card simultaneously.Bluetooth wireless technology has the following features:Worldwide operationThe Bluetooth radio transmitter and receiver operate in the 2.4 GHz band, which is license-free and compatible with radio systems in most countries in the world.■The values shown above are the theoretical maximums for Wireless LAN standards. The actual values may differ.■The transmission speed over the wireless LAN, and the distance over which the wireless LAN can reach, may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, client design and software/hardware configurations. The transmission rate described is the theoretical maximum speed as specified under the appropriate standard - the actual transmission speed will be lower than the theoretical maximum speed.
User’s Manual 4-38Operating BasicsRadio linksYou can easily establish links between two or more devices. The link is maintained even if the devices are not within line of sight.SecurityTwo advanced security mechanisms ensure a high level of security:■Authentication prevents access to critical data and makes it impossible to falsify the origin of a message.■Encryption prevents eavesdropping and maintains link privacy.Bluetooth® Stack for Windows® by TOSHIBAPlease note that this software is specifically designed for the following operating systems:■Microsoft® Windows® 2000 Professional■Microsoft® Windows® XPDetailed information regarding the use with these operating systems is listed below. Please refer also to the electronic information which is included with each software. Release Notes related to the Bluetooth® Stack for Windows®by TOSHIBA1. Install:When installing the Bluetooth® Stack for Windows® by TOSHIBA software under Windows 2000 or Windows XP, please be aware that it is not digitally signed.2. Fax application software:There is some fax application software that you cannot use on this Bluetooth® Stack.3. Multi User:On Windows XP, the use of Bluetooth is not supported in a multi-user environment. This means that, when you use Bluetooth, other users logged onto the same computer will not be able to use its Bluetooth functionality.Product Support:The latest information regarding Operating System support, Language Support or available upgrades can be found on our web site http://www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe or www.pcsupport.toshiba.com in the United States.This Bluetooth® Stack is based on the Bluetooth® Version 1.1/1.2/2.0+EDR specification. TOSHIBA cannot confirm compatibility between any PC products and/or other electronic devices that use Bluetooth® other than TOSHIBA mobile computers.
User’s Manual 4-39Operating BasicsWireless communication switchYou can enable or disable Wireless LAN and Bluetooth functions, with the on/off switch. No transmissions are sent or received when the switch is off. Slide the switch to the right to turn it on and to the left to turn it off.Wireless communication IndicatorThe wireless communication indicator indicates the status of the wireless communication functions.If you used the Task Bar to disable the wireless LAN, restart the computer or perform the following procedure to re-enable it : start,Control Panel,System,Hardware, Device Manager,Network adapters, Intel®PRO/Wireless 3945BG/3945ABG Network Connection or Atheros AR5006EG/AR5006EX Wireless Network Adapter and enable.■Do not use the Wireless LAN (Wi-Fi) or Bluetooth functionalities near a microwave oven or in areas subject to radio interference or magnetic fields. Interference from a microwave oven or other source can disrupt Wi-Fi or Bluetooth operation.■Turn Wi-Fi and Bluetooth functionalities off when near a person who may have a cardiac pacemaker implant or other medical electric device. Radio waves may affect pacemaker or medical device operation, possibly resulting in serious injury. Follow the instruction of your medical device when using any Wi-Fi or Bluetooth functionality.■Always turn off Wi-Fi or Bluetooth functionality if the PC is near automatic control equipment or appliances such as automatic doors or fire detectors. Radio waves can cause malfunction of such equipment, possibly resulting in serious injury.Indicator status IndicationIndicator off Wireless communication switch is set to off. Automatic power down because of overheating. Power malfunction.Indicator glows Wireless communication switch is on. Wireless LAN or Bluetooth is turned on by an application.
User’s Manual 4-40Operating BasicsLANThe computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) and Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T).This section describes how to connect/disconnect to a LAN.LAN cable typesIf you are using Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T), be sure to connect with a CAT5E cable or higher. You cannot use a CAT3 or CAT5 cable.If you are using Fast Ethernet LAN (100 megabits per second, 100BASE-TX), be sure to connect with a CAT5 cable or higher. You cannot use a CAT3 cable.If you are using Ethernet LAN (10 megabits per second, 10BASE-T), you can connect with a CAT3 or higher cable.Connecting LAN cableTo connect the LAN cable, follow the steps below.Do not install or remove an optional memory module while Wake-up on LAN is enabled.■The Wake-up on LAN function consumes power even when the system is off. Leave the AC adaptor connected while using this feature.■The Link speed (10/100/1000 megabits per second) changes automatically depending on the network conditions (connected device, cable or noise and so on).The computer must be configured properly before connecting to a LAN. Logging onto a LAN using the computer’s default settings could cause a malfunction in LAN operation. Check with your LAN administrator regarding set-up procedures.■Connect the AC adaptor before connecting the LAN cable. The AC adaptor must remain connected during LAN use. If you disconnect the AC Adaptor while the computer is accessing a LAN, the system may hang up.■Do not connect any other cable to the LAN jack except the LAN cable. Otherwise, malfunctions or damage may occur.■Do not connect any power supplying device to the LAN cable that is connected to the LAN jack. Otherwise, malfunctions or damage may occur.
User’s Manual 4-41Operating Basics1. Turn off the power to the computer and to all external devices connected to the computer.2. Plug one end of the cable into the LAN jack. Press gently until you hear the latch click into place.Figure 4-21 Connecting the LAN cable 3. Plug the other end of the cable into a LAN hub connector. Check with your LAN administrator before connecting to a hub. Disconnecting LAN cableTo disconnect the LAN cable, follow the steps below.1. Pinch the lever on the connector in the computer’s LAN jack and pull out the connector.2. Disconnect the cable from the LAN hub in the same manner. Check with your LAN administrator before disconnecting from the hub.LAN jackLAN connectorWhen the computer is exchanging data with the LAN, the LAN Activeindicator glows orange. When the computer is connected to a LAN hub but is not exchanging data, the Link indicator glows green.Make sure the LAN Active indicator (orange LED) is out before you disconnect the computer from the LAN.
User’s Manual 4-42Operating BasicsCleaning the computerTo help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer.■Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely before you turn it on again.■Clean the computer using a slightly damp (with water) cloth. You can use glass cleaner on the LCD display screen. Spray a small amount of cleaner on a soft, clean cloth and wipe the screen gently with the cloth.Moving the computerThe computer is designed for rugged durability. However, a few simple precautions taken when moving the computer will help ensure trouble-free operation.■Before moving the computer, it is recommended that you change the function of the TOSHIBA HDD Protection. Refer to the section, Using the Hard Disk Drive (HDD) Protection, in this chapter.■Make sure all disk activity has ended before moving the computer. Check the HDD indicator on the computer.■If a CD/DVD is in the drives, remove it. Also make sure the disc tray is securely closed.■Turn off the power to the computer.■Disconnect the AC adaptor and all peripherals before moving the computer.■Close the LCD display panel. Do not pick up the computer by its display panel.■Before carrying your computer, shut down the computer, disconnect the power cable and wait until the PC cools down. Failure to follow this instruction could result in minor injury.■Always turn off the power when you move the computer. If the power button has a lock, set it to the lock position. Also be careful not to subject the computer to impact. Failure to follow this instruction could result in damage to computer, computer failure or loss of data.■Never transport your computer with PC cards installed. This could cause damage to your computer and/or PC card, resulting in product failure.■Use a carrying case when transporting the computer.■When carrying your computer, be sure to hold it securely so that it does not fall or hit anything.■Do not carry your computer by holding any protruding areas.Never spray cleaner directly onto the computer or let liquid run into any part of it. Never use harsh or caustic chemical products to clean the computer.
User’s Manual 4-43Operating BasicsUsing the Hard Disk Drive (HDD) ProtectionThis computer has a function for reducing the risk of damage on the hard disk drive.Using an acceleration sensor built into the computer, TOSHIBA HDD Protection detects vibration shocks and similar signs of movement of the computer, and automatically moves the Hard Disk Drive head to a safe position to reduce the risk of damage that could be caused by head-to-disk contact. When vibration is detected, the following message is displayed, and the icon in the notification area of the taskbar is changed to the protection state. This message is displayed until the OK button is pressed or 30 seconds pass. When vibration subsides, the icon returns to the normal state.Figure 4-22 TOSHIBA HDD Protection MessageTaskbar Icon■This function does not guarantee that the hard disk drive will not be damaged.■The secondary hard disk drive is not supported by the TOSHIBA HDD protection function.State Icon DescriptionNormal TOSHIBA HDD Protection is enabled.Protection TOSHIBA HDD Protection is active. The hard disk drive head is in a safe position.OFF TOSHIBA HDD Protection is disabled.
User’s Manual 4-44Operating BasicsTOSHIBA HDD Protection PropertiesYou can change the TOSHIBA HDD Protection settings by using the TOSHIBA HDD Protection Properties window. To open the window, click start, point to All Programs, point to TOSHIBA, point to Utilities and click HDD Protection Setting. The window can also be started from the icon on the Taskbar or from the Control Panel.Figure 4-23 TOSHIBA HDD Protection PropertiesHDD ProtectionYou can choose whether to enable or disable TOSHIBA HDD Protection.Detection LevelThis function can be set to four levels. The sensitivity levels in which vibrations, impacts and their similar signs are detected can be set to OFF, 1, 2 and 3 in ascending order. Level 3 is recommended for better protection of the computer. However, when the computer is used in a mobile environment or in other unstable conditions, setting the detection level to 3 could result in frequent execution of TOSHIBA HDD Protection, which will slow Hard Disk Drive reading and writing. Set a lower detection level when the speed of Hard Disk Drive reading and writing is a priority.Different detection levels can be set depending on whether the computer is used as handheld or mobile usages, or whether it is used in a stable environment such as on a table in the workplace or at home. By setting different detection levels for the computer depending on whether it runs with the AC power (desktop) or with batteries (handheld or mobile usage), the detection level automatically switches according to the power connection mode.
User’s Manual 4-45Operating BasicsDetailsTo open the Details window, click the Setup Detail button in the TOSHIBA HDD Protection Properties window.Figure 4-24 DetailsDetection Level AmplificationWhen the AC adaptor is disconnected or the lid is closed, HDD Detection assumes that the computer will be carried and sets the detection level to the maximum for 10 seconds.TOSHIBA HDD Protection MessageSpecify whether to display a message when TOSHIBA HDD Protection is active.Heat dispersalTo protect from overheating, the CPU has an internal temperature sensor. If the computer’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered. You can select whether to control the CPU temperature by turning on the fan first, then if necessary, lowering the CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the Cooling Method item of the Basic Setup tab in TOSHIBA Power Saver.When the CPU temperature falls to a normal range, the fan is turned off and the CPU operation returns to standard speed.■This function does not work when the computer is starting, in standby, in hibernation, in transition to hibernation, recovering from hibernation, or powered off. Be sure to not subject the computer to vibration or impact while the function is disabled.■This function only operates with Windows® XP.If the CPU temperature reaches an unacceptably high level with either setting, the system automatically shuts down to prevent damage. Data in memory will be lost.
User’s Manual 5-1Chapter 5The KeyboardThe computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer.The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages are available.There are six types of keys: typewriter keys, function keys, soft keys, Hot keys, Windows special keys and keypad overlay. Typewriter keysThe typewriter keys produce the upper- and lower-case letters, numbers, punctuation marks, and special symbols that appear on the screen.There are some differences, however, between using a typewriter and using a computer keyboard:■Letters and numbers produced in computer text vary in width. Spaces, which are created by a "space character," may also vary depending on line justification and other factors.■The lowercase l (el) and the number 1 (one) are not interchangeable on computers as they are on a typewriter.■The uppercase O (oh) and the 0 (zero) are not interchangeable.■The Caps Lock function key locks only the alphabetic characters in uppercase while the shift lock on a typewriter places all keys in the shifted position.■The Shift keys, the Tab key, and the BkSp (backspace) key perform the same function as their typewriter counterparts but also have special computer functions.Never remove the key caps on your keyboard. Doing so could cause damage to the parts under the key caps.
User’s Manual 5-2The KeyboardFunction keys: F1 … F12The function keys (not to be confused with Fn) are the 12 keys at the top of your keyboard. These keys function differently from other keys.F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fnkey, keys marked with icons execute specific functions on the computer. Refer to the section, Soft keys: Fn key combinations, in this chapter. The function executed by individual keys depends on the software you are using. Soft keys: Fn key combinationsThe Fn (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.Emulating keys on enhanced keyboardFigure 5-1 A 101-key enhanced keyboard layoutThe keyboard is designed to provide all the features of the 101-key enhanced keyboard. The 101/102-key enhanced keyboard has a numeric keypad and scroll lock key. It also has additional Enter and Ctrl keys to the right of the main keyboard. Since the keyboard is smaller and has fewer keys, some of the enhanced keyboard functions must be simulated using two keys instead of one on the larger keyboard.Your software may require you to use keys that the keyboard does not have. Pressing the Fn key and one of the following keys simulates the enhanced keyboard’s functions.Some software may disable or interfere with soft-key operations. Soft-key settings are not restored by the Standby feature.Esc#3Home PgUpBk SpF1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 ! 12$4%568 (9 )0&7_+=PgDnEndShiftDelInsCapsLockShiftEnterQW RTYU I O P {[}]E~`ASDFGHJ KL:;@?/> .< ,MNVCXZB\^*+-TabAltAltEnter    7Home8    9PgUp654  1End2   3PgDn 0InsNumLock  .Del PrtSc Scroll lockPauseBreakCtrlCtrlSysReq/*.,,,
User’s Manual 5-3The KeyboardPress Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the keys with gray markings on the bottom edge become numeric keypad keys (Fn + F11) or cursor control keys (Fn +F10). Refer to the Keypad overlay section in this chapter for more information on how to operate these keys. The power on default for both settings is off.Press Fn +F12 (ScrLock) to lock the cursor on a specific line. The power on default is off.Press Fn +Enter to simulate Enter on the enhanced keyboard’s numeric keypad.Press Fn +Ctrl to simulate the enhanced keyboard’s right Ctrl key.Hot keysHot keys (Fn + a function or Esc key) let you enable or disable certain features of the computer.Sound mute: Pressing Fn + Esc in a Windows environment turns sound on or off. When you press these hot keys, the current setting will change and be displayed as an icon. Pressing the Volume control dial turns Mute off. Refer to the Right side section in Chapter 2 for details.
User’s Manual 5-4The KeyboardInstant security: Press Fn +F1 to blank the screen to prevent others from accessing your data. To restore the screen and original settings, press any key or press the Touch Pad. If a screensaver password is registered, a dialog box will appear. Enter the screensaver password and click OK. If no password is set, the screen will be restored when you press any key or press the Touch Pad.Power save mode: Pressing Fn +F2 changes the power save mode.If you press Fn + F2 in a Windows environment, the settings dialog box for the Power Save Mode will be displayed. Continue holding down Fn, and release and press F2 again to toggle between the settings. Release both Fn and F2 to put the new setting into effect. You can also change this setting through the Profile options in TOSHIBA Power Saver.Standby: When you press Fn + F3, the computer enters the Standby Mode. Before entering Standby, a dialog box appears asking for your confirmation. This dialog box will not be displayed in the future if you click the check box.Hibernation: When you press Fn + F4, the computer enters the Hibernation Mode. Before entering Hibernation, a dialog box appears asking for your confirmation. This dialog box will not be displayed in the future if you click the check box.Display selection: Press Fn +F5 to change the active display device. When you press these hot keys, a dialog box appears. Only selectable devices will be displayed. Hold down Fn and press F5 again to change the device. When you release Fn and F5, the selected device will change. If you hold down these hot keys for five seconds the selection will return to the internal LCD.
User’s Manual 5-5The KeyboardInternal LCD screen Brightness: Pressing Fn + F6 decreases the LCD screen brightness in decrements. When you press these hot keys, the current setting will be displayed for two seconds by an icon. You can also change this setting through the Screen brightness item of the Basic Setup tab in TOSHIBA Power Saver. Internal LCD screen Brightness: Pressing Fn + F7 increases the LCD screen brightness in increments. When you press these hot keys, the current setting will be displayed for two seconds by a pop-up icon. You can also change this setting through the Screen brightness item of the Basic Setup tab in TOSHIBA Power Saver.Wireless setting: If your computer has both Bluetooth and Wireless LAN functions, you can press Fn +F8 to select which type of wireless communication you want to use. When you press these hot keys, a dialog box will appear. Continue holding down Fn and press F8 to change the setting. If wireless communication is turned off, Disabled Wireless Communication Switch will be displayed.Touch Pad: Pressing Fn + F9 in a Windows environment enables or disables the Touch Pad function. When you press these hot keys, the current setting will change and be displayed as an icon.■The brightness level is always set at the maximum value for about 18 seconds, when the internal LCD screen turns on.■LCD screen clarity increases with the brightness level.If no wireless communication device is installed, no dialog box will appear.
User’s Manual 5-6The KeyboardLCD screen resolution selection: Press Fn +Space keys to change the display resolution. Each time when you press these hot keys, the LCD screen resolution changes as follows: The available resolution depends on the model. With WXGA+, you can change the resolution between 800 × 600 and 1440 × 900 pixels.Optical Drive Power: Press the Fn +Tab keys to turn the power of the optical disc drive on or eject the disc tray. A dialog box is displayed when this hotkey is pressed. To choose between the functions, press the Tab key while holding down the Fn key. The chosen function is executed when the Fn +Tab keys are released.TOSHIBA Zooming Utility (reduce): To reduce the icon size on the desktop or the application window, press the 1 key while holding down theFn key.TOSHIBA Zooming Utility (enlarge): To enlarge the icon size on the desktop or the application window, press the 2key while holding down the Fn key.Fn Sticky keyYou can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and then press an "F number" key. To start the TOSHIBA Accessibility Utility, click start, point to AllPrograms, point to TOSHIBA, point to Utilities and click Accessibility.
User’s Manual 5-7The KeyboardWindows special keysThe keyboard provides two keys that have special functions in Windows: Windows logo key activates the start menu and the other, the application key, has the same function as the secondary mouse button.This key activates the Windows start menu.This key has the same function as the secondary mouse button. Keypad overlayYour computer’s keyboard does not have an independent numeric keypad, but its numeric keypad overlay functions like one.The keys in the center of the keyboard with gray letters make up the numeric keypad overlay. The overlay provides the same functions as the numeric keypad on the 101/102-key enhanced keyboard.Turning on the overlaysThe numeric keypad overlay can be used for numeric data input or cursor and page control.Arrow modeTo turn on the Arrow mode, press Fn +F10. The Arrow mode indicator lights. Now try cursor and page control using the keys. Press Fn +F10again to turn off the overlay.
User’s Manual 5-8The KeyboardNumeric modeTo turn on the Numeric mode, press Fn +F11. The Numeric mode indicator lights. Now try numeric data entry using the keys. Press Fn +F11again to turn off the overlay.Figure 5-2 The numeric keypad overlayTemporarily using normal keyboard (overlay on)While using the overlay, you can temporarily access the normal keyboard without turning off the overlay:1. Hold Fn and press any other key. All keys will operate as if the overlay was off.2. Type upper-case characters by holding Fn + Shift and pressing a character key.3. Release Fn to continue using the overlay.Temporarily using overlay (overlay off)While using the normal keyboard, you can temporarily use the keypad overlay without turning it on:1. Press and hold down Fn.2. Check the keyboard indicators. Pressing Fn turns on the most recently used overlay. If the Numeric mode indicator lights, you can use the overlay for numeric entry. If the Arrow mode indicator lights, you can use the overlay for cursor and page control.3. Release Fn to return to normal keyboard operation.
User’s Manual 5-9The KeyboardTemporarily changing modesIf the computer is in Numeric mode, you can switch temporarily to Arrow mode by pressing a shift key. If the computer is in Arrow mode, you can switch temporarily to Numericmode by pressing a shift key. Generating ASCII charactersNot all ASCII characters can be generated using normal keyboard operation. But, you can generate these characters using their ASCII codes.With the overlay on:1. Hold down Alt.2. Using the overlay keys, type the ASCII code.3. Release Alt, and the ASCII character appears on the display screen.With the overlay off:1. Hold down Alt +Fn.2. Using the overlay keys, type the ASCII code.3. Release Alt + Fn, and the ASCII character appears on the display screen.
User’s Manual 6-1Chapter 6Power and Power-Up ModesThe computer’s power resources include the AC adaptor, battery pack and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.Power conditionsThe computer’s operating capability and battery charge status are affected by the power conditions: whether an AC adaptor is connected, whether a battery pack is installed and what the charge level is for the battery. Table 6-1 Power conditions Power onPower off (no operation)ACadaptor connectedMain Battery fully charged  • Operates • No charge • LED: Battery greenDC IN green • No charge • LED: Battery greenDC IN greenMain Battery partially charged or no charge • Operates • Charge*1 • LED: Battery orangeDC IN green • Quick charge*1 • LED: Battery orangeDC IN greenNo Main battery installed   • Operates  • No charge • LED: Battery offDC IN green • No charge • LED: Battery offDC IN green
User’s Manual 6-2Power and Power-Up ModesTable 6-1 Power conditions continued Power onPower off (no operation)ACadaptor connected2nd battery fully charged  • Operates • No charge • LED: 2nd battery greenDC IN green • No charge • LED: 2nd battery greenDC IN green2nd battery partially charged or no charge • Operates • Charge*2 • LED: 2nd battery orangeDC IN green • Quick charge*2 • LED: 2nd battery orangeDC IN greenNo 2nd battery  installed   • Operates  • No charge • LED: 2nd battery offDC IN green • No charge • LED: 2nd battery offDC IN greenACadaptor not connectedMain battery charge is above low battery trigger point • Operates • LED: Battery offDC IN offMain battery charge is below low battery trigger point • Operates • LED: Battery flashes orangeDC IN offMain battery charge is exhausted Computer shuts down *3No main battery installed  • No operation *4 • LED: Battery offDC IN off
User’s Manual 6-3Power and Power-Up ModesTable 6-1 Power conditions continued*1 When the Slice Expansion battery is not charging.*2 When the main battery is not charging.*3 For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window. If a main battery and a Slice Expansion battery are installed, the computer does not shut down until the charge in both batteries is exhausted.*4 When no Slice Expansion battery is installed.*5 When no main battery is installed. Power onPower off (no operation)ACadaptor not connected2nd battery charge is above low battery trigger point • Operates • LED: 2nd battery offDC IN off2nd battery charge is below low battery trigger point • Operates • LED: 2nd batteryflashes orangeDC IN off2nd battery charge is exhaustedComputer shuts down *3No 2nd battery is installed  • No operation *5 • LED: 2nd battery offDC IN offWhen batteries are charged, the main battery is charged first. When it is fully charged, the Slice Expansion battery is charged.
User’s Manual 6-4Power and Power-Up ModesPower indicatorsAs shown in the above table, the Battery, 2nd battery, DC IN and Powerindicators on the system indicator alert you to the computer’s operating capability and battery charge status.Battery indicatorCheck the Battery indicator to determine the status of the main battery and the 2nd battery indicator to determine the status of the Slice Expansion battery. The following indicator lights indicate the battery status:DC IN indicatorCheck the DC IN indicator to determine the power status with the AC adaptor connected:Flashing orange The battery charge is low. The AC adaptor must be connected to recharge the battery.Orange Indicates the AC adaptor is connected and charging the battery.Green Indicates the AC adaptor is connected and the battery is fully charged.No light Under any other conditions, the indicator does not light.If the battery pack becomes too hot while it is being charged, the charge will stop and the Battery indicator will go out. When the battery pack’s temperature falls to a normal range, charge will resume. This occurs whether the computer’s power is on or off.Green Indicates the AC adaptor is connected and supplying proper power to the computer.Flashing orange Indicates a problem with the power supply. Plug the AC adaptor into another power outlet. If it still does not operate properly, contact your dealer.No light Under any other conditions, the indicator does not light.
User’s Manual 6-5Power and Power-Up ModesPower indicatorCheck the Power indicator to determine the power status:Battery typesThe computer has three types of batteries:■Battery pack■Slice Expansion Battery (Provided with some models, or option)■Real Time Clock (RTC) batteryBattery packWhen the AC adaptor is not connected, the computer’s main power source is a removable lithium ion battery pack, also referred to in this manual as the main battery. You can purchase additional battery packs for extended use of the computer away from an AC power source.Do not change the battery pack while the AC adaptor is connected.Before you remove the battery pack, save your data and shut down the computer, or set the computer to Hibernation Mode. While entering Hibernation Mode, the computer saves the contents of memory to the hard disk drive. However, for safety sake, it is best to save your data manually.Green Indicates power is being supplied to the computer and the computer is turned on.Blinking orange Indicates power is being supplied to the computer while the computer is in Standby Mode. The indicator turns on for one second and off for two seconds.No light Under any other conditions, the indicator does not light.■The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements.■Always use the battery pack supplied as an accessory or an equivalent battery pack specified in the User's Manual. Other battery packs have different voltage and terminal polarities. Use of non-conforming battery packs could generate smoke or cause fire or rupture, possibly resulting in serious injury.■Always dispose of used battery packs in compliance with all applicable laws and regulations. Put insulating tape, such as cellophane tape, on the electrode during transportation to avoid a possible short circuit, fire or electric shock. Failure to do so could possibly result in serious injury.
User’s Manual 6-6Power and Power-Up ModesTo ensure that the battery pack maintains its maximum capacity, operate the computer on battery power at least once a month until the battery pack is fully discharged. Refer to Extending battery life in this chapter for procedures. If the computer is continuously operated on AC power through an AC adaptor for an extended period, more than a month, the battery may fail to retain a charge. It may not function efficiently over the expected life of the battery and the Battery indicator may not indicate a low-battery condition.Slice Expansion Battery (Provided with some models, or option)The Slice Expansion Battery is included with some models, or can be purchased separately as an optional accessory.For detailed information on this battery, refer to Slice Expansion Batterysection in Chapter 3.Real Time Clock (RTC) batteryThe Real Time Clock (RTC) battery provides power for the internal real time clock and calendar. It also maintains the system configuration.If the RTC battery becomes completely discharged, the system loses this data and the real time clock and calendar stop working. The following message appears when you turn on the power:S**** RTC battery is low or CMOS checksum is inconsistent ****    Press [F1] key to set Date/Time. You can change the Real Time Clock settings by pressing the F1 key. Refer to Chapter 8 Troubleshooting for detail.■Do not remove the battery pack while the computer is in Standby Mode. Data is stored in RAM, so if the computer loses power it will be lost. When the computer is powered off in Standby Mode, and the AC adaptor is not connected, the battery pack supplies power to maintain data and programs in memory. If the battery pack is completely discharged, Standby Mode will not function and the computer loses all data in memory.The Slice Expansion Battery is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements.The computer’s RTC battery is a Ni-MH battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations.The RTC battery does not charge while the computer is turned off even if the AC adapter is attached.
User’s Manual 6-7Power and Power-Up ModesCare and use of the battery packThe battery pack is a vital component of portable computing. Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your battery pack. Follow the instructions in this section carefully to ensure safe operation and maximum performance.Refer to the enclosed Instruction Manual for Safety & Comfort for detailed precautions and handling instructions.■Make sure the battery is securely installed in the computer before attempting to charge the battery pack. Improper installation could generate smoke or fire, or cause the battery pack to rupture.■Keep the battery pack out of reach of infants and children. It can cause injury.■Use only battery packs recommended by TOSHIBA as replacements.■Charge the battery pack only in an ambient temperature between 5 and 35 degrees Celsius. Otherwise, the electrolyte solution might leak, battery pack performance might deteriorate and the battery life might be shortened.■Never install or remove the battery pack without first turning off the power and disconnecting the AC adaptor. Never remove the battery pack while the computer is in Standby Mode. Data will be lost.■Never remove the battery pack while the Wake-up on LAN function is enabled. Data will be lost. Before you remove a battery pack, disable the Wake-up on LAN function.■Never remove the battery pack while the Wake-up on Wireless LAN function is enabled. Data will be lost. Before you remove a battery pack, disable the Wake-up on Wireless LAN function.■To ensure the battery pack maintains maximum capacity, operate the computer on battery power once a week until the battery pack is fully discharged. Refer to the section Extending battery life in this chapter for procedures. If the computer is continuously operated on AC power for an extended period, more than a week, the battery might fail to retain a charge. It might not function efficiently over the expected life of the battery pack and the Battery indicator might not indicate a low-battery condition.■After the battery pack is charged, avoid leaving the AC adaptor connected and the computer turned off for more than a few hours at a time. Continuing to charge a fully-charged battery pack can damage the battery.
User’s Manual 6-8Power and Power-Up ModesCharging the batteriesWhen the power in the battery pack becomes low, the Battery indicator flashes orange indicating that only a few minutes of battery power remain. If you continue to use the computer while the Battery indicator flashes, the computer enables Hibernation Mode (so you don’t lose data) and automatically turns off.You must recharge a battery pack when it becomes discharged.ProceduresTo recharge a battery pack while it is installed in the computer, connect the AC adaptor to the DC IN 15V jack and plug the other end into a working outlet.The Battery indicator glows orange when the battery is being charged.TimeThe following table shows the approximate time required to fully charge a discharged battery.Charging time (hours)Battery charging noticeThe battery may not charge right away under the following conditions:■The battery is extremely hot or cold. If the battery is extremely hot, it might not charge at all. To ensure the battery charges to its full capacity, charge the battery at room temperature of 10° to 30°C (50° to 88°F). The computer enters Hibernate mode only if Hibernation is enabled in two places: the Hibernate tab in Power Options and Setup Actions tab in TOSHIBA Power Saver.Use only the computer connected to an AC power source or the optional TOSHIBA Battery charger to charge the battery pack. Never attempt to charge the battery pack with any other charger.Battery type Power on Power offBattery pack (4700mAh) about 3.0 to 13.0 about 3.0Slice Expansion Battery (4000mAh) about 3.0 to 9.5 about 3.0RTC battery 8Doesn't chargeThe charging time when the computer is on is affected by ambient temperature, the temperature of the computer and how you use the computer. If you make heavy use of external devices, for example, the battery might scarcely charge at all during operation. Refer also to the section Maximizing battery operating time.
User’s Manual 6-9Power and Power-Up Modes■The battery is nearly completely discharged. Leave the AC adaptor connected for a few minutes and the battery should begin charging.The Battery indicator may show a rapid decrease in battery operating time when you try to charge a battery under the following conditions:■The battery has not been used for a long time.■The battery has completely discharged and been left in the computer for a long time.■A cool battery is installed in a warm computer.In such case, follow the steps below.1. Fully discharge the battery by leaving it in the computer with the power on until the power automatically shuts off.2. Connect the AC adaptor to the DC IN 15V jack of the computer, and the AC adaptor into power outlet.3. Charge the battery until the Battery indicator glows green.Repeat these steps two or three times until the battery recovers normal capacity.Monitoring battery capacityRemaining battery power can be monitored in TOSHIBA Power Saver. Maximizing battery operating timeA battery’s usefulness depends on how long it can supply power on a single charge.How long the charge lasts in a battery depends on:■How you configure the computer (for example, whether you enable battery-power saving options). The computer provides a battery save mode, which can be set in TOSHIBA Power Saver, to conserve battery power. This mode has the following options:■CPU Processing speedLeaving the AC adaptor connected will shorten battery life. At least once a month, run the computer on battery power until the battery is fully discharged, then recharge the battery.■Wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time. The computer needs this time to check the battery’s remaining capacity and to calculate the remaining operating time, based on the current power consumption rate and remaining battery capacity. The actual remaining operating time may differ slightly from the calculated time.■With repeated discharges and recharges, the battery’s capacity will gradually decrease. Therefore, an often used, older battery will not operate for as long as a new battery even when both are fully charged. In this case, TOSHIBA Power Saver will indicate a 100% charge for both the old and new battery, but the displayed estimated time remaining will be shorter for the older battery.
User’s Manual 6-10Power and Power-Up Modes■Screen brightness■Cooling Method■System standby■System Hibernation■Monitor Power off■HDD Power off■How often and how long you use the hard disk, optical disc and the floppy disk drive.■How much charge the battery contained to begin with.■How you use optional devices, such as a PC card, to which the battery supplies power.■Enabling Standby Mode conserves battery power if you are frequently turning the computer off and on.■Where you store your programs and data. ■Closing the LCD display panel when you are not using the keyboard saves power.■Operating time decreases at low temperatures.■The condition of the battery terminals. Make sure the battery terminals stay clean by wiping them with a clean dry cloth before installing the battery pack. Retaining data with power offWhen you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods:Retention timeExtending battery lifeTo maximize the life of your battery pack:■At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps below.Battery type State and Retention TimeBattery pack (4700mAh) about 5 days (Standby Mode)about 60 days (Boot mode)Slice Expansion Battery (4000mAh) about 5 days (Standby Mode)about 50 days (Boot mode)RTC battery 30 days1. Turn off the computer’s power.2. Disconnect the AC adaptor and turn on the computer’s power. If it does not turn on go to step 4.
User’s Manual 6-11Power and Power-Up Modes■If you have extra battery packs, rotate their use.■If you will not be using the system for an extended period, more than one month, remove the battery pack.■Disconnect the AC adaptor when the battery is fully charged. Overcharging makes the battery hot and shortens life.■If you are not going to use the computer for more than eight hours, disconnect the AC adaptor. ■Store spare battery packs in a cool dry place out of direct sunlight.Replacing the battery packThe battery pack is classified as a consumable item.The operating life of the battery pack will gradually reduce through repeated charging and discharging. It will need to be replaced when it reaches the end of its operating life.You might also replace a discharged battery pack with a charged spare when you are operating your computer away from an AC power source. This section explains how to remove and install the battery pack.To remove a discharged battery pack, follow the steps below.1. Save your work.2. Turn the computer’s power off. Make sure the Power indicator is off.3. Remove all cables connected to the computer.4. Close the LCD display panel and turn the computer upside down.3. Operate the computer on battery power for five minutes. If the battery pack has at least five minutes of operating time, continue operating until the battery pack is fully discharged. If the Batteryindicator flashes or there is some other warning to indicate a low battery, go to step 4.4. Connect the AC adaptor to the computer and the power cord to a power outlet. The DC IN indicator should glow green, and the Battery indicator should glow orange to indicate that the battery pack is being charged. If the DC IN indicator does not glow, power is not being supplied. Check the connections for the AC adaptor and power cord.5. Charge the battery pack until the Battery indicator glows green.■Do not remove the battery pack while the computer is in Standby Mode. Data is stored in RAM, so if the computer loses power it will be lost.■In Hibernation Mode, data will be lost if you remove the battery pack or disconnect the AC adaptor before the save is completed. Wait for the HDD indicator to go out.■Do not touch the battery release latch while holding the computer or the battery pack might fall out due to the unintentional release of the battery release latch and cause injuries.
User’s Manual 6-12Power and Power-Up Modes5. Slide the battery safety lock towards the release ( ) position to make the battery release latch movable.Figure 6-1 Releasing the battery pack (1)6. Slide the battery release latch (1) to free the battery pack for removal (2), then slide out the battery pack.Figure 6-2 Releasing the battery pack (2)To install a battery pack, follow the steps below.7. Insert the battery pack (1). Battery packBattery release latchBattery lockBattery release latchBattery packDo not touch the battery release latch while holding the computer. Or you may get injured by the dropped battery pack by unintentional release of the battery release latch.
User’s Manual 6-13Power and Power-Up Modes8. Make sure that the battery pack is securely in place and the battery lock (2) is in the lock position ( ).Figure 6-3 Securing the battery pack9. Return your computer to the upright position.TOSHIBA Password UtilityThe TOSHIBA Password Utility provides two levels of password security: User and Supervisor.User PasswordTo start the utility, point to or click the following items:start -> All Programs -> TOSHIBA -> Utilities ->Password UtilityThe User Password dialog box contains two main fields: User Password and User Token.User authentication may be required to validate user rights when using "TOSHIBA Password Utility" to delete or change passwords, or create tokens, etc. User Password field■Set (button)Click this button to register a password of up to 50 characters. After a password is set, you will be prompted to enter it when you start the computer. Check "Set the same string simultaneously as the HDD User Password" when setting the HDD User Password.Battery packBattery lockPasswords set in the TOSHIBA Password Utility are different from the Windows password.
User’s Manual 6-14Power and Power-Up Modes■Delete (button)Click this button to delete a registered password. Before you can delete a password, you must first enter the current password correctly or insert a proper token. Please use BIOS Setup to change or delete the HDD Passwords or to set the HDD Master Password.■Change (button)Click this button to change a registered password. Before you can change a password, you must first enter the current password correctly or insert a proper token. Please use BIOS Setup to change or delete the HDD Passwords or to set the HDD Master Password.■Owner String (text box)You can use this box to associate text with the password. After you enter text, click Apply or OK. When the computer is started, this text will be displayed together with the prompt asking you to enter a password.■After you set the password, a dialog box will be displayed asking whether you want to save it to a floppy disk or other media. If you forget the password, you can open the password file on another computer. Be sure to keep the media in a safe place.■When entering the character string to register the password, enter from the keyboard character by character and do not enter as ASCII code or copy-and-paste the character string. In addition, ensure that the registered password is correct by outputting the character string to the password file.■If you forget your HDD User Password, TOSHIBA will NOT be able to assist you, and your HDD will be rendered COMPLETELY and PERMANENTLY INOPERABLE. TOSHIBA will NOT be held responsible for any loss of any data, any loss of use or access to your HDD, or for any other losses to you or any other person or organization that result from the loss of access to your HDD. If you can’t accept this risk, don’t register the HDD User Password.■When saving the HDD User Password shut down or restart the computer. If the computer is not shut down or restarted, the saved data may not be correctly reflected. For more information on shutting down or restarting the computer, refer to Turning on the power in Chapter 1. Refer to Starting and Ending the BIOS Setup Program section in Chapter 7 for more information.
User’s Manual 6-15Power and Power-Up ModesUser Token field■Create (button)You can use an SD card token, instead of entering the password. After you have registered a password, insert an SD card in SD card slot and click Create. You can use an SD card of any capacity, but it must be formatted correctly.If an unformatted card or one with an incompatible format is inserted, you will be prompted to format it with a tool named TOSHIBA SD Memory Card Format. To start the format tool, point to or click the following items:start -> All Programs -> TOSHIBA -> Utilities -> SD Memory Card Format■Disable (button)Click this button to invalidate the token. You cannot re-validate old tokens, but you can use the same SD cards to create new tokens.Supervisor PasswordIf you set a Supervisor Password, some functions might be restricted when a user logs on with the User Password. To set a Supervisor Password, execute the file TOSPU.EXE. The file is located at:C:\Program Files\Toshiba\Windows Utilities\SVPWTool\TOSPU.EXEThis utility lets you do the following:■Register, delete or change the Supervisor Password.■Create or invalidate a Supervisor Password token.■Specify restrictions for general users.When you format an SD Memory card, all data will be deleted. Be sure to save data on the card to other media before you format the card.After using the token created for authentication, do not leave it inserted in the SD card slot, ensure that the token is removed from the slot and stored in a safe location. If the token is left in the slot, there is a danger of theft or a third party using it for authentication and operating the user's computer (resulting in extraction, modification or deletion of data) when the user is not at their desk.This function in the TOSHIBA Password Utility lets you invalidate only supervisor tokens or all tokens, including user and supervisor tokens.
User’s Manual 6-16Power and Power-Up ModesStarting the computer by passwordIf you have already registered a password, there are three ways to start the computer:■Insert an SD card token before you turn on the computer. The computer will start normally, without displaying a password prompt.■Swipe your fingerprint on the sensor if you have already registered the fingerprint with the Fingerprint utility and enabled Fingerprint System Boot Authentication. If you would not like to swipe your finger or cannot authenticate the fingerprint for some reasons, push the BkSp key to skip the fingerprint authentication screen. You can try to swipe the fingerprint up to five times. If you failed fingerprint authentication five times, you must enter the password manually to start the computer.■Log on with the Tablet PC Pen when in Tablet mode. Refer to Tablet mode section in this chapter.■Enter the password manually.To enter a password manually, follow these steps:1. Turn on the power as described in Chapter 1, Getting Started. The following message will appear in the LCD:SPassword=2. Enter the Password.3. Press Enter.The password is necessary only if the computer was Shutdown and Hibernation in boot mode.It is not needed in Standby and Restart.If you enter the password incorrectly three times in a row, the computer shuts off. In this case, you must turn the computer back on to retry password entry.
User’s Manual 6-17Power and Power-Up ModesTablet modeEnter your password by tapping the on-screen keyboard using the Tablet PC Pen.Figure 6-4 On-screen keyboard■The beep sounds when tapping the on-screen keyboard with the Tablet PC Pen. An * (asterisk) is displayed after "Password =" and one character is input for every tapping.Power-up modesThe computer has the following power-up modes:■Boot: Computer shuts down without saving data. Always save your work before you turn the computer off in boot mode.■Hibernation: Data in memory is saved to the hard disk drive. ■Standby: Data is maintained in the computer’s memory.Windows utilitiesYou can configure various settings associated with both Standby Mode and Hibernation Mode within TOSHIBA Power Saver.Hot keysYou can use hot keys Fn + F3 to enter Standby Mode and Fn + F4 to enter Hibernation. Refer to Chapter 5, The Keyboard for details.Register your password to the computer in the laptop mode using the standard keyboard. Refer to TOSHIBA Password Utility, in this chapter for the detail.Refer also to the sections Turning on the power and Turning off the powerin Chapter 1, Getting Started.
User’s Manual 6-18Power and Power-Up ModesPanel power on/offYou can set up your computer so that power turns off automatically when you close the display panel. When you open the panel, power will be turned on in Standby Mode or Hibernation Mode but not in boot mode. System Auto OffThis feature turns the system off automatically if it is not used for a set duration. The system shuts down in Standby Mode or Hibernation Mode in Windows.If the panel power off function is enabled and you manually shut down Windows, do not close the computer’s LCD display panel until the shut down process has been completed.
User’s Manual 7-1Chapter 7HW Setup & BIOS SetupThis chapter explains how to use TOSHIBA HW Setup program to configure your computer, and provides information on setting up the Execute-Disable Bit Capability and TPM.Accessing HW SetupTo run HW Setup, click start, click Control Panel, click Printers andOther Hardware and select TOSHIBA HWSetup.HW Setup windowThe HW Setup window contains the following tabs: General, Display, Boot Priority, Keyboard, CPU, LAN, Device Config and USB.There are also three buttons: OK,Cancel and Apply.OK Accepts your changes and closes the HW Setup window. Cancel Closes the window without accepting your changes. Apply Accepts all your changes without closing the HW Setup window.
User’s Manual 7-2HW Setup & BIOS SetupGeneralThis window displays the BIOS version and contains two buttons: Defaultand About.SetupThis field displays BIOS Version and date.DisplayThis tab lets you customize your computer’s display settings for either the internal LCD screen or an external monitor.Power On DisplayLets you select the display to be used when the computer is booted (This setting is only available on Standard VGA mode and is not available on Windows Desktop properties).Default Return all HW Setup values to the factory settings.About Display the HW Setup version. Auto-Selected Selects an external monitor if one is connected. Otherwise, it selects the internal LCD (Default).LCD + Analog RGB Selects both the internal LCD and external monitor for simultaneous display.System LCD Only Selects the internal LCD even if the external monitor is connected.If the connected external monitor does not support the computer's current video mode, selecting the LCD + Analog RGB mode will not display any image on the external monitor.When Windows starts up, the screen will be displayed on the external monitor if it was connected when the notebook was previously switched off and is still connected when the computer is switched on. Otherwise, the screen will be displayed on the internal LCD.
User’s Manual 7-3HW Setup & BIOS SetupBoot PriorityBoot Priority OptionsThis option sets the priority for booting the computer. Select from the following settings:You can override the settings and manually select a boot device by pressing one of the following keys while the computer is booting: *1 The floppy disk drive will be used to start the computer when there is a bootable disk contained in the external drive. If SD memory is installed as well, the external floppy disk drive will be checked first, followed by the SD memory device itself.*2The optical disc drive will be used to start the computer when there is a bootable disk contained in the drive.HDD !FDD !CD-ROM !LANThe computer looks for bootable files in the following order: HDD, floppy disk drive*1, CD-ROM*2 and LAN (Default).FDD !HDD !CD-ROM !LANThe computer looks for bootable files in the following order: floppy disk drive*1, HDD, CD-ROM*2 and LAN.HDD !CD-ROM !LAN !FDDThe computer looks for bootable files in the following order: HDD, CD-ROM*2, LAN and floppy disk drive*1.FDD !CD-ROM !LAN !HDDThe computer looks for bootable files in the following order: floppy disk drive*1, CD-ROM*2,LAN and HDD.CD-ROM !LAN !HDD !FDDThe computer looks for bootable files in the following order: CD-ROM*2, LAN, HDD, floppy disk drive*1.CD-ROM !LAN !FDD !HDDThe computer looks for bootable files in the following order: CD-ROM*2, LAN, floppy disk drive*1 and HDD.USelects the USB floppy disk drive.NSelects the network.1Selects the built-in HDD.CSelects the CD-ROM*2.MSelects the USB Memory.
User’s Manual 7-4HW Setup & BIOS SetupTo change the boot drive, follow the steps below.1. Hold down F12 and boot the computer.2. The following menu will be displayed with the following icons: Built-in HDD, CD-ROM, FDD (or SD memory card), Network (LAN), USB Memory boot.3. Use the left/right cursor keys to highlight the boot device you want and press Enter.A bar will appear only under the selected device.■If only a Supervisor Password has been set, the following should be noted:■The boot device menu will appear when the 'Able to run HW Setup' option has been configured.■The boot device menu will not appear when the 'Unable to run HW Setup' option has been configured.■If both a Supervisor Password and a User Password are set, the following should be noted:■The boot device menu will appear when you use either the Supervisor Password or the User Password to start the computer, and the 'Able to run HW Setup' option has been configured.■The boot device menu will not appear when you use the User Password to start the computer and the 'Unable to run HW Setup' option has been configured.■The boot device menu will appear when you use the Supervisor Password to start the computer, even if the 'Unable to run HW Setup' option has been configured.The boot device selection methods described above will not change the boot priority settings that have been configured in HW Setup. In addition, if you press a key other than one of those listed, or if the selected device is not installed, the system will continue to boot according to the current and available settings in HW Setup.
User’s Manual 7-5HW Setup & BIOS SetupHDD Priority OptionsIf more than one HDD is installed in the computer, this option lets you set the priority for HDD detection. If the first detected HDD has a boot command, the system will boot from the HDD.Network Boot ProtocolThis feature sets the protocol to remotely boot from the network. [PXE] Sets PXE as the protocol (Default).[RPL] Sets RPL as the protocol.USB Memory BIOS Support TypeSet the type of the USB memory as a startup device.KeyboardWake-up on KeyboardWhen this feature is enabled and the computer is in Standby Mode, you can turn on the computer by pressing any key. It is effective only for the internal keyboard and only when the computer is in Standby Mode.Built-in HDD -> USB (Default)The priority is set as Built-in HDD -> USB.USB -> Built-in HDDThe priority is set as USB -> Built-in HDD.■If a boot command is not found on the first detected HDD, the system will not boot from the other HDD. It will search the next device in the boot priority for a boot command.■Some modules may not be displayed.Network Boot Protocol is not displayed for Gigabit Ethernet LAN.HDD Set the type of the USB memory to be equivalent to the HDD (Default).* Based on the [HDD] order in the [Boot Priority Options] item. The order with respect to the other HDD can be set in the [HDD Priority Options] item.FDD Set the type of the USB memory to be equivalent to the FDD.* Based on the [FDD] order in the [Boot Priority Options] item.Enabled Enables the Wake-up on Keyboard function.Disabled Disables the Wake-up on Keyboard function (Default).
User’s Manual 7-6HW Setup & BIOS SetupCPUThis function lets you set the CPU operating mode.Dynamic CPU Frequency ModeThis option lets you choose from the following settings:LANWake-up on LANThis feature lets the computer’s power be turned on when it receives a wake-up signal from the LAN.Built-in LANThis feature enables or disables the Built-in LAN.This option is displayed only for models with an Intel® CoreTM Duo processor and Intel® CoreTM Solo processor.Dynamically SwitchableCPU power consumption and clock speed automatic switching function is enabled. When the computer is in use, CPU operation is automatically switched when necessary (Default).Always High CPU power consumption and clock speed automatic switching function is disabled. The CPU always runs at its fastest speed.Always Low CPU power consumption and clock speed automatic switching function is disabled. The CPU always runs at low power consumption and low speed.Enabled Enables Wake-up on LAN.Disabled Disables Wake-up on LAN (Default).Do not install or remove an optional memory module while Wake-up on LAN is enabled.The Wake-up on LAN function consumes power even when the system is off. Leave the AC adaptor connected while using this feature.Enabled Enables Built-in LAN functions (Default).Disabled Disables Built-in LAN functions.
User’s Manual 7-7HW Setup & BIOS SetupDevice ConfigDevice ConfigurationThis option lets you set the device configuration. USBUSB KB/Mouse Legacy EmulationUse this option to enable or disable USB keyboard/mouse legacy emulation. If your operating system does not support USB, you can still use a USB mouse and keyboard by setting the USB KB/Mouse Legacy Emulation item to Enabled.USB-FDD Legacy EmulationUse this option to enable or disable USB floppy disk drive legacy emulation. If your operating system does not support USB, you can still use a USB floppy disk drive by setting the USB-FDD Legacy Emulation item to Enabled.All Devices BIOS sets all devices.Setup by OS Operating system sets devices that it can control (Default).Enabled Enables the USB KB/Mouse Legacy Emulation function (Default).Disabled Disables the USB KB/Mouse Legacy Emulation function.Enabled Enables the USB floppy disk drive legacy emulation function (Default).Disabled Disables the USB floppy disk drive legacy emulation function.
User’s Manual 7-8HW Setup & BIOS SetupBIOS Setup ProgramSettings for some features are carried out in the BIOS setup program.Starting and Ending the BIOS Setup ProgramStarting the BIOS Setup Program1. Switch on your computer while pressing the Esc key. If "Password =" is displayed, enter either the Supervisor Password, if one is set, or the User Password and press the Enter key.Please refer to Chapter 6, the TOSHIBA Password Utility, for details about the User Password. The "Check system.Then press [F1] key." message is displayed.2. Press the F1 key.The BIOS setup program will start up.Ending the BIOS Setup ProgramSave the changes and end the program.1. Press the End Key.The "Are you sure? (Y/N) The changes you made will cause the system to reboot." message is displayed.2. Press the Y key.The configured settings are saved and the BIOS setup program ends.The computer may reboot depending on the settings that were modified.Notes before using the BIOS Setup■In most cases, changes to the system's configuration should be made within Windows by using applications such as TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Windows Device Manager and so forth. If you make changes to the configuration through the BIOS setup program, please be aware that the configuration set through the Windows applications will take priority.■Changes to the settings within the BIOS setup program will not be erased even if the power supply is switched off and the main battery removed. However, if the built-in Real Time Clock (RTC) battery runs out of power, most of the settings will revert back to their default values. However, please note that the following items will not be affected in this instance:• Password • Hard Disk Drive Password • Security controllerPlease refer to the operating instructions displayed in the settings screen.
User’s Manual 7-9HW Setup & BIOS SetupEnding the BIOS Setup Program HalfwayThe configuration settings can be terminated halfway without saving any of the changes made.1. Press the Esc key.The "Exit without saving? (Y/N)" message is displayed.2. Press the Y key.The BIOS setup program will end.Core Multi - ProcessingThe Core Multi-Processing sets the CPU operating mode. Enabled is Dual Core mode.Disabled is Single Core mode.Virtualization TechnologyVirtualization Technology sets enable or disable of the Intel Virtualization Technology installed in the CPU.Intel Virtualization Technology is the technique that allows one machine to operate as multiple virtual machines.The Disabled command does not allow use of the Intel Virtualization Technology.The Enabled command allows use of the Intel Virtualization Technology.Enhanced C-StatesThis feature enables or disables the Enhanced C-States.This option is displayed only on models with an Intel®CoreTM Duo processor.Enabled Enables Core Multi - Processing functions (Default).Disabled Disables Core Multi - Processing functions.The Virtualization Technology is supported with some models.Enabled Enables Virtualization Technology.Disabled Disables Virtualization Technology (Default).This option is displayed only on models with an Intel®CoreTM Duo processor and Intel®CoreTM Solo processor.Enabled This lowers the power consumption (Default).Disabled This does not lower the power consumption.
User’s Manual 7-10HW Setup & BIOS SetupExecute-Disable Bit CapabilityThis setting, which is displayed on the first page of the setup screen, configures the Execute-Disable Bit function of the CPU. This function is specific to Intel processors and, when activated, helps to reduce security threats to the computer by preventing certain classes of malicious 'buffer overflow' attacks when combined with a supporting operating system such as Windows XP.Security controllerThe security controller settings are available in SYSTEM SETUP (2/2).TPMThis setting enables or disables the security controller known as TPM (Trusted Platform Module).Clear TPM OwnerThis setting is used to erase the data in TPM when disposing of the computer or when the owner of the computer changes, etc. Once this operation is carried out, the TPM configuration settings are erased, such that the encrypted data can no longer be decrypted and the files can no longer be read. Please backup or delete the data as necessary before carrying out this operation.The operating procedure is as follows:1. Move the cursor to the Clear TPM Owner setting and press the Space key or BkSp key.2. A message is displayed. Press the Y,E,S, and Enter keys and the TPM information is erased.3. The TPM setting changes from being displayed as Enable to Disabled,and the setting is no longer displayed.Available Makes the processor's Execute-Disable Bit Capability available for use.Not Available Disables the processor's Execute-Disable Bit Capability so that it is not available for use. (Default).System configuration changes, other than changes to this setting, should be made within Windows by using applications such as TOSHIBA HW Setup,TOSHIBA Password Utility, TOSHIBA Power Saver,Windows Device Manager and so forth.Enabled Enables the TPM.Disabled Disables the TPM (Default).
User’s Manual 7-11HW Setup & BIOS SetupDiagnostic ModeSet whether the BIOS Setup Diagnostic test is enabled.■System configuration changes other than changes to this setting should be made in Windows using TOSHIBA HW Setup,TOSHIBA Password Utility,TOSHIBA Power Saver,Device Manager,etc.■When using TPM, please install the Infineon TPM Installation Guidefrom the TOSHIBA Application Installer.Please ensure that the user reads the Infineon TPM Installation Guide as it contains usage information and notes on using TPM.Disabled The Diagnostic test is disabled (Default).Enabled The Diagnostic test is enabled.
User’s Manual 8-1Chapter 8TroubleshootingTOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause.All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.Problem solving processResolving problems will be much easier if you observe the following guidelines:■Stop immediately when you recognize a problem exists. Further action may result in data loss or damage. You may destroy valuable problem-related information that can help solve the problem.■Observe what is happening. Write down what the system is doing and what actions you performed immediately before the problem occurred. If you have a printer attached, print a copy of the screen using PrtSc.The questions and procedures offered in this chapter are meant as a guide, they are not definitive problem solving techniques. Many problems can be solved simply, but a few may require help from your dealer. If you find you need to consult your dealer or others, be prepared to describe the problem in as much detail as possible.
User’s Manual 8-2TroubleshootingPreliminary checklistConsider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem.■Make sure you turn on all peripheral devices before you turn on the computer. This includes your printer and any other external device you are using.■Before you attach an external device, turn the computer off. When you turn the computer back on it recognizes the new device.■Make sure all options are set properly in the setup program.■Check all cables. Are they correctly and firmly attached? Loose cables can cause signal errors.■Inspect all connecting cables for loose wires and all connectors for loose pins.■Check that your floppy disk or CD/DVD-ROM is correctly inserted and that the floppy disk’s write protect tab is correctly set.Make notes of your observations and keep them in a permanent error log. This will help you describe your problems to your dealer. If a problem recurs, the log will help you identify the problem faster.Analyzing the problemSometimes the system gives clues that can help you identify why it is malfunctioning. Keep the following questions in mind:■Which part of the system is not operating properly: keyboard, floppy disk drives, hard disk drive, optical disc drive, display. Each device produces different symptoms.■Is the operating system configuration set properly? Check the configuration options.■What appears on the display screen? Does it display any messages or random characters? If you have a printer attached, print a copy of the screen using PrtSc. Look up the messages in the software and operating system documentation. Check that all connecting cables are correctly and firmly attached. Loose cables can cause erroneous or intermittent signals.■Do any indicators light? Which ones? What color are they? Do they stay on or blink? Write down what you see.■Do you hear any beeps? How many? Are they long or short? Are they high pitched or low? Is the computer making any unusual noises? Write down what you hear.Record your observations so you can describe them to your dealer.
User’s Manual 8-3TroubleshootingHardware and system checklistThis section discusses problems caused by your computer’s hardware or attached peripherals. Basic problems may occur in the following areas:System start-up When the computer does not start properly, check the following items:■Self Test■Power Sources■Power-on Password Software The problems may be caused by your software or disk. If you cannot load a software package, the media may be damaged or the program might be corrupted. Try loading another copy of the software.If an error message appears while you are using a software package, check the software documentation. These documents usually include a problem solving section or a summary of error messages.Next, check any error messages in the operating system documentation.Hardware If you cannot find a software problem, check your hardware. First run through the items in the preliminary checklist above. If you still cannot correct the problem, try to identify the source. The next section provides checklists for individual components and peripherals.Before using a peripheral device or application software that is not an authorized Toshiba part or product, make sure the device or software can be used with your PC. Use of incompatible devices may cause injury or may damage your PC.■System start-up■Self test■Power■Password■Keyboard■Internal LCD display panel■Hard disk drive■DVD-ROM■DVD-ROM&CD-R/RW drive■DVD Super Multi drive■USB floppy disk drive■PC card■SD card■Memory Stick/Memory Stick Pro■xD picture card■MultiMediaCard■Pointing Device■Fingerprint Sensor■USB device■Memory expansion■Sound system■External monitor■TV output signal■i.LINK (IEEE1394) device■Modem■LAN■Wireless LAN■Bluetooth
User’s Manual 8-4TroubleshootingSelf test When the computer starts up, the self test will be run automatically, and the following will be displayed:This message remains on the screen for a few seconds.If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program.If any of the following conditions are present, the self test failed:■The computer stops and does not proceed to display information or messages except the TOSHIBA logo.■Random characters appear on the screen, and the system does not function normally.■The screen displays an error message.Turn off the computer and check all cable connections. If the test fails again, contact your dealer.PowerWhen the computer is not plugged into an AC outlet, the battery pack is the primary power source. However, your computer has a number of other power resources, including an intelligent power supply and a Real Time Clock battery. These resources are interrelated and any one could affect apparent power problems. This section provides checklists for AC power and the battery. If you cannot resolve a problem after following them, the cause could lie with another power resource. In such case, contact your dealer.Overheating power downIf the computer’s internal temperature becomes too high, the computer will automatically enter Hibernation or Standby Mode and shut down.SIn Touch with TomorrowTOSHIBAProblem ProcedureComputer shuts down and DC IN indicator blinks orangeLeave the computer off until the DC IN indicator stops blinking.It is recommended to leave the computer off until the interior reaches room temperature even though the DC IN indicator stops blinking.
User’s Manual 8-5TroubleshootingAC powerIf you have trouble turning on the computer with the AC adaptor connected, check the DC IN indicator. Refer to Chapter 6, Power and Power-Up Modes for more information.BatteryIf you suspect a problem with the battery, check the DC IN indicator as well as the Battery indicator. For information on indicators and battery operation see Chapter 6, Power and Power-Up Modes.If the computer has reached room temperature and still does not start, or if it starts but shuts down quickly contact your dealer.Computer shuts down and its DC IN indicator is flashing greenIndicates a problem with the heat dispersal system. Please contact your dealer.Problem ProcedureAC adaptor doesn’t power the computer (DC IN indicator does not glow green)Check the connections. Make sure the cord is firmly connected to the computer and a power outlet.Check the condition of the cord and terminals. If the cord is frayed or damaged, replace it. If the terminals are soiled, wipe them with cotton or a clean cloth.If the AC adaptor still does not power the computer, contact your dealer.Problem ProcedureBattery doesn’t power the computer  The battery may be discharged. Connect the AC adaptor to charge the battery.
User’s Manual 8-6TroubleshootingBattery doesn’t charge when the AC adaptor is attached (Batteryindicator does not glow orange.)If the battery is completely discharged, it will not begin charging immediately. Wait a few minutes.If the battery still does not charge, make sure the outlet of the AC adaptor is supplying power. Test it by plugging in an appliance.Check whether the battery is hot or cold to the touch. If the battery is too hot or too cold, it will not charge properly. Let it reach room temperature.Unplug the AC adaptor and remove the battery to make sure the terminals are clean. If necessary wipe them with a soft dry cloth dipped in alcohol.Connect the AC adaptor and replace the battery. Make sure it is securely seated.Check the Battery indicator. If it does not glow, let the computer charge the battery for at least 20 minutes. If the Battery indicator glows after 20 minutes, let the battery continue to charge at least another 20 minutes before turning on the computer.If the indicator still does not glow, the battery may be at the end of its operating life. Replace it.If you do not think the battery is at the end of its operating life, see your dealer.Battery doesn’t power the computer as long as expectedIf you frequently recharge a partially charged battery, the battery might not charge to its full potential. Fully discharge the battery, then try to charge it again.Check the power consumption settings in TOSHIBA Power Saver. Consider using a power saving mode.Problem Procedure
User’s Manual 8-7TroubleshootingReal Time ClockPasswordKeyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, The Keyboard.Problem ProcedureThe following message is Displayed on the LCD screen:RTC battery is low or CMOS checksum is inconsistent. Press [F1] key to set Date/Time.The charge in the RTC battery has run out - you will need to set the date and time in the BIOS setup using the following steps:1. Press F1 key. BIOS setup will boot up.2. Set the date in System Date.3. Set the time in System Time.4. Press End key. Confirmation message will appear.5. Press Y key. BIOS setup will terminate and the computer will be rebooted.Problem ProcedureCannot enter password Refer to the TOSHIBA Password Utility section in Chapter 6, Power and Power-Up Modes.Problem ProcedureSome letter keys produce numbers  Check that the numeric keypad overlay is not selected. Press Fn + F11 and try typing again.Output to screen is garbled Make sure the software you are using is not remapping the keyboard. Remapping involves reassigning the meaning of each key. See your software’s documentation.If you are still unable to use the keyboard, consult your dealer.
User’s Manual 8-8TroubleshootingInternal LCD display panelApparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, HW Setup & BIOS Setup, for more information.Hard disk driveProblem ProcedureNo display Press hotkeys Fn +F5 to change the display priority, to make sure it is not set for an external monitor.Markings appear on the LCD screen. The marks may have come from contact with the keyboard or Touch Pad. Try wiping the LCD screen gently with a clean dry cloth. If markings remain, use a good quality LCD screen cleaner, taking care to ensure you let the LCD screen dry before closing it.Problems above remain unresolved or other problems occurRefer to your software’s documentation to determine if the software is causing the difficulty.Run the diagnostic test.Contact your dealer if the problems continue.Problem ProcedureComputer does not boot from hard disk driveCheck if a floppy disk is in the floppy disk drive or a CD-ROM is in the optical disc drive. Remove any floppy disk and/or CD-ROM and check the Boot priority. Refer to the Boot Priority section in Chapter 7, HW Setup & BIOS Setup.There may be a problem with your operating system files. Refer to your operating system documentation.Slow performance Your files may be fragmented. Run Disk Defragmenter to check the condition of your files and disk. Refer to your operating system’s documentation or online HELP for information on running the Disk Defragmenter.As a last resort, reformat the hard disk. Then, reload the operating system and other files.If problems persist, contact your dealer.
User’s Manual 8-9TroubleshootingDVD-ROM driveFor more information, refer to Chapter 4, Operating Basics.Problem ProcedureYou cannot access a CD/DVD in the drive Make sure the drive’s disc tray is securely closed. Press gently until it clicks into place.Check whether the drive power is on. If the power is off, click on the Optical Drive Power icon in the task tray and turn on the power.Open the disc tray and make sure the CD/DVD is properly seated. It should lie flat with the label facing up.A foreign object in the disc tray could block laser light from reading the CD/DVD. Make sure there is no obstruction. Remove any foreign object.Check whether the CD/DVD is dirty. If it is, wipe it with a clean cloth dipped in water or a neutral cleaner. Refer to the Media caresection in Chapter 4 for details on cleaning.Some CD/DVDs run correctly, but others do not The software or hardware configuration may be causing a problem. Make sure the hardware configuration matches your software’s needs. Check the CD/DVD’s documentation.Check the type of CD/DVD you are using. The drive supports:DVD-ROM: DVD-ROM, DVD-VideoCD-ROM: CD-DA, CD-Text, Photo CDTM(single/multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-EXTRA), Addressing Method 2Check the region code on the DVD. It must match that on the DVD-ROM drive. Region codes are listed in the Optical disc drivessection in Chapter 2, The Grand Tour.If problems persist, contact your dealer.
User’s Manual 8-10TroubleshootingDVD-ROM&CD-R/RW driveFor more information, refer to Chapter 4, Operating Basics.Problem ProcedureYou cannot access a CD/DVD in the drive Make sure the drive’s disc tray is securely closed. Press gently until it clicks into place.Check whether the drive power is on. If the power is off, click on the Optical Drive Power icon in the task tray and turn on the power.Open the disc tray and make sure the CD/DVD is properly seated. It should lie flat with the label facing up.A foreign object in the disc tray could block laser light from reading the CD/DVD. Make sure there is no obstruction. Remove any foreign object.Check whether the CD/DVD is dirty. If it is, wipe it with a clean cloth dipped in water or a neutral cleaner. Refer to the Media care section in Chapter 4 for details on cleaning.Some CD/DVDs run correctly, but others do notThe software or hardware configuration may be causing a problem. Make sure the hardware configuration matches your software’s needs. Check the CD/DVD’s documentation.Check the type of CD/DVD you are using. The drive supports:DVD-ROM: DVD-ROM, DVD-VideoCD-ROM: CD-DA, CD-Text, Photo CDTM(single/multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-EXTRA), Addressing Method 2Recordable CD: CD-R, CD-RWCheck the region code on the DVD. It must match that on the DVD-ROM&CD-R/RW drive. Region codes are listed in the Optical disc drivessection in Chapter 2, The Grand Tour.
User’s Manual 8-11TroubleshootingDVD Super Multi driveFor more information, refer to Chapter 4, Operating Basics.Cannot write correctly  If you have trouble writing, make sure you are observing the following precautions:■Use only media recommended by TOSHIBA.■Do not use the mouse or keyboard during writing.■Use only the software supplied with the computer for recording.■Do not run or start other software during writing.■Do not jar the computer during writing.■Do not connect/disconnect external devices or install/remove internal cards during writing.If problems persist, contact your dealer.Problem ProcedureProblem ProcedureYou cannot access a CD/DVD in the driveMake sure the drive’s disc tray is securely closed.Press gently until it clicks into place.Check whether the drive power is on. If the power is off, click on the Optical Drive Power icon in the task tray and turn on the power.Open the disc tray and make sure the CD/DVD is properly seated. It should lie flat with the label facing up.A foreign object in the disc tray could block laser light from reading the CD/DVD. Make sure there is no obstruction. Remove any foreign object.Check whether the CD/DVD is dirty. If it is, wipe it with a clean cloth dipped in water or a neutral cleaner. Refer to the Media care section in Chapter 4 for details on cleaning.Some CD/DVDs run correctly, but others do notThe software or hardware configuration may be causing a problem. Make sure the hardware configuration matches your software’s needs. Check the CD/DVD's documentation.
User’s Manual 8-12TroubleshootingUSB floppy disk driveFor more information, refer to Chapter 3, Features, Utilities and Options.PC cardRefer also to Chapter 3, Features, Utilities and Options.Check the type of CD/DVD you are using. The drive supports:DVD-ROM: DVD-ROM, DVD-VideoCD-ROM: CD-DA, CD-Text, Photo CDTM(single/multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-EXTRA), Addressing Method 2Recordable DVD: DVD-R/-R DL, DVD+R/+R DL, DVD-RW, DVD+RW, DVD-RAMCheck the region code on the DVD. It must match that on the DVD Super Multi drive. Region codes are listed in the Optical disc drives section in Chapter 2, The Grand Tour.Problem ProcedureDrive does not operate There may be a faulty cable connection. Check the connection to the computer and to the drive.Some programs run correctly but others do notThe software or hardware configuration may be causing a problem. Make sure the hardware configuration matches your software needs.You cannot access the external 3 1/2" floppy disk driveTry another floppy disk. If you can access the floppy disk, the original floppy disk (not the drive) is probably causing the problem.If problems persist, contact your dealer.Problem ProcedurePC card error occurs  Reseat the PC card to make sure it is firmly connected.Make sure the connection between the external device and the card is firm.Check the card’s documentation.If problems persist, contact your dealer.
User’s Manual 8-13TroubleshootingSD cardRefer also to Chapter 3, Features, Utilities and Options.Memory Stick/Memory Stick ProRefer also to Chapter 3, Features, Utilities and Options.xD picture cardRefer also to Chapter 3, Features, Utilities and Options.Problem ProcedureSD card error occurs  Reseat the SD card to make sure it is firmly connected.Check the card’s documentation.You cannot write to an SD memory card Make sure the card is not write protected.You cannot read a file Make sure the target file is on the SD memory card inserted in the slot.If problems persist, contact your dealer.Problem ProcedureMemory Stick/Memory Stick Pro error occurs  Reseat the Memory Stick/Memory Stick Pro to make sure it is firmly connected.Check the card’s documentation.You cannot write to an Memory Stick/Memory Stick ProMake sure the Memory Stick/Memory Stick Pro is not write protected.You cannot read a file Make sure the target file is on the Memory Stick/Memory Stick Pro inserted in the slot.If problems persist, contact your dealer.Problem ProcedurexD picture card error occurs Reseat the xD picture card to make sure it is firmly connected.Check the card’s documentation.You cannot read a file Make sure the target file is on the xD picture card inserted in the slot.If problems persist, contact your dealer.
User’s Manual 8-14TroubleshootingMultiMediaCardRefer also to Chapter 3, Features, Utilities and Options.Pointing deviceIf you are using a USB mouse, also refer to the USB section in this chapter and to your mouse documentation.Touch PadProblem ProcedureMultiMediaCard error occurs  Reseat the MultiMediaCard to make sure it is firmly connected.Check the MultiMediaCard’s documentation.You cannot write to an MultiMediaCard Make sure the MultiMediaCard is not write protected.You cannot read a file Make sure the target file is on the MultiMediaCard inserted in the slot.If problems persist, contact your dealer.Problem ProcedureOn-screen pointer does not respond to Pad operationThe system might be busy. If the pointer is shaped as an hourglass, wait for it to return to its normal shape and try again to move it.Double-tapping does not work Try changing the double-click speed setting in the mouse control utility.1. Click start, click Control Panel, click Printers and Other Hardware and select Mouse icon. 2. Click the Buttons tab.3. Set the double-click speed as required and click OK.
User’s Manual 8-15TroubleshootingUSB mouseThe mouse pointer moves too fast or too slowTry changing the speed setting in the mouse control utility.1. Click start, click Control Panel, click Printers and Other Hardware and select Mouse icon. 2. Click the Pointer Options tab.3. Set the speed as required and click OK.If problems persist, contact your dealer.The reaction of Touch pad is either too sensitive or not sensitive enough.Adjust the touch Sensitivity.1. Click start and open the Control Panel.2. Click the Printers and Other Hardware icon.3. Click the Mouse icon.4. Click the Advanced tab.5. Click the Advanced feature settings button.6. Click Touch Pad tab. Click the Settingsbutton in the Pointer speed and tapping settings.7. Detailed Touch Pad setting is displayed.8. Move the slide of adjust the pointer speed in relation to the standard Windows setting. Click the OK button.9. Click the OK button on Advanced feature setting screen.Problem ProcedureOn-screen pointer does not respond to mouse operationThe system might be busy. If the pointer is shaped as an hourglass, wait for it to resume its normal shape and try again to move it.Make sure the mouse is properly connected to the USB port.Double-clicking does not work Try changing the double-click speed setting in the mouse control utility.1. Click start, click Control Panel, click Printers and Other Hardware and select Mouse icon. 2. Click the Buttons tab.3. Set the double-click speed as required and click OK.Problem Procedure
User’s Manual 8-16TroubleshootingFingerprint SensorThe mouse pointer moves too fast or too slowTry changing the speed setting in the mouse control utility.1. Click start, click Control Panel, click Printers and Other Hardware and select Mouse icon. 2. Click the Pointer Options tab.3. Set the speed as required and click OK.The mouse pointer moves erratically The mouse might be dirty. Refer to your mouse documentation for instructions on cleaning.If problems persist, contact your dealer.Problem ProcedureProblem ProcedureReading of the fingerprint was not successful.Try again using the correct posture. Align your fingertip with the sensor as shown in the drawing and swipe. Refer to Using the Fingerprint Sensorin Chapter 4, Operating Basics.Try the recognition process again using another enrolled finger.The fingerprint cannot be read due to injuries to the finger.Try the recognition process again using another enrolled finger.If fingerprints from all the enrolled fingers cannot be read, please logon by using the keyboard to input the password for the time being.If problems persist, contact your dealer.
User’s Manual 8-17TroubleshootingUSB deviceRefer also to your USB device’s documentation.Memory expansionRefer also to Chapter 3, Features, Utilities and Options, for information on installing memory modules.Problem ProcedureUSB device does not work Check for a firm cable connection between the USB ports on the computer and the USB device.Make sure the USB device drivers are properly installed. Refer to your Windows XP documentation for information on checking the drivers.If you are using an operating system that does not support USB, you can still use a USB mouse and/or USB keyboard. If these devices do not work, make sure the USB KB/Mouse Legacy Emulation item in HW Setup is set to Enabled.If problems persist, contact your dealer.Problem ProcedureIf there is a memory malfunction, the power LED flashes (on for 0.5 seconds, off for 0.5 seconds) in the following ways;If there is only an error in Slot A: repeatedly flashes orange twice, then green.If there is only an error in Slot B: repeatedly flashes orange, then green twice.If there is an error in Slot A and in Slot B: repeatedly flashes orange twice, then green twice.Make sure the memory module installed in the memory slot is compatible with the computer.If an incompatible module has been installed, follow the steps below.1. Turn off the computer.2. Disconnect the AC adaptor and all peripheral devices.3. Remove the battery pack.4. Remove the memory module.5. Install the battery and/or connect the AC adaptor.6. Turn on the power.If problems persist, contact your dealer.
User’s Manual 8-18TroubleshootingSound systemRefer also to documentation for your audio devices.External monitorRefer also to Chapter 3, Features, Utilities and Options, and to your monitor’s documentation.Problem ProcedureNo sound is heard Adjust the volume control dial.Check the software volume settings.Make sure the headphone connection is secure. If problems persist, contact your dealer.Check Windows Device Manager. Make sure the sound function is enabled and that settings for I/O address, Interrupt level and DMA are correct for your software and do not conflict with other hardware devices that you may have connected to the computer.Annoying soundis heardYou may be experiencing feedback. Refer to Sound System in Chapter 4, Operating Basics.If problems persist, contact your dealer.Problem ProcedureMonitor does not turn on Make sure that the external monitor’s power switch is on. Confirm that the external monitor’s power cable is plugged into a working power outlet.No display Try adjusting the contrast and brightness controls on the external monitor.Press hot keys Fn + F5 to change the display priority and make sure it is not set for the internal LCD.Display error occurs Check that the cable connecting the external monitor to the computer is attached firmly.If problems persist, contact your dealer.
User’s Manual 8-19TroubleshootingTV output signali.LINK (IEEE1394) deviceModemRefer to Appendix C, AT Commands and Appendix D,S-registers.Problem ProcedureDisplay on TV is poor Make sure the TV type is correct for your area: NTSC (US, JAPAN), PAL (Europe).No display Try adjusting the contrast and brightness controls on the external monitor.Press hotkeys Fn + F5 to change the display. Refer to Chapter 5, The Keyboard.If problems persist, contact your dealer.If you turn the computer off into Standby Mode while the display is on TV, the computer will select either the internal LCD or an external computer CRT as the display device the next time is switched on.Problem Procedurei.LINK device does not function Make sure the cable is securely connected to the computer and to the device.Make sure the device’s power is turned on.Reinstall the drivers. Open the Windows Control Panel and double-click the AddHardware icon. Follow the on-screen directions.Restart Windows.If problems persist, contact your dealer.Problem ProcedureCommunication software can’t initialize modemMake sure the computer’s internal modem settings are correct. Refer to Phone and ModemProperties in the Control Panel.You can hear a dial tone but can’t make a callIf the call is going through a PBX machine, make sure the communication application’s tone dial detection feature is disabled.You can also use the ATX command. Refer to Appendix C, AT Commands.
User’s Manual 8-20TroubleshootingLANYou place a call, but a connection can’t be madeMake sure the settings are correct in your communications application.After making a call you can’t hear a ring  Make sure the tone or pulse selection in your communications application is set correctly.You can also use the ATD command. Refer to Appendix C, AT Commands.Communication is cut off unexpectedly The computer will automatically cut off communication when connection with the carrier is not successful for a set time interval. Try lengthening this time interval.ACONNECT display is quickly replaced by NOCARRIERCheck the error control setting in your communications application.You can also use the AT\N command. Refer to Appendix C, AT Commands.Character display becomes garbled during a communication sessionIn data transmission, make sure the parity bit and stop bit settings correspond with those of the remote computer.Check the flow control and communication protocol.You cannot receive an incoming call Check the rings before auto answer setting in  your communications application. You can also use the ATS0 command. Refer to Appendix D, S-registers.If problems persist, contact your dealer.Problem ProcedureProblem ProcedureCannot access LAN  Check for a firm cable connection between the LAN jack and the LAN hub.Wake-up on LAN does not work Make sure the AC adaptor is connected. The Wake-up on LAN function consumes power even when the system is off.If problems persist, consult your LAN administrator.
User’s Manual 8-21TroubleshootingWireless LANIf the following procedures do not restore LAN access, consult your LAN administrator. For more information on wireless communication, refer to Chapter 4, Operating Basics.BluetoothFor more information on wireless communication, refer to Chapter 4, Operating Basics.Disposing of PC and PC batteries■Discard this PC in accordance with applicable laws and regulations. For further information, contact your local government.■This PC contains rechargeable batteries. After repeated use, the batteries will finally lose their ability to hold a charge and you will need to replace them. Under certain applicable laws and regulation, it may be illegal to dispose of old batteries by placing them in the trash. ■Please be kind to our shared environment. Check with your local government authority for details regarding where to recycle old batteries or how to dispose of them properly. This product contains mercury. Disposal of this material may be regulated due to environmental considerations. For disposal, reuse or recycling information, please contact your local government.Problem ProcedureCannot access Wireless LAN Make sure the computer’s wireless communication switch is set to on.If problems persist, contact your LAN administrator.Problem ProcedureCannot access Bluetooth device Make sure the computer’s wireless communication switch is set to on.Make sure the Bluetooth Manager is running and the power to the Bluetooth device is turned on.Make sure no optional Bluetooth PC card and Bluetooth SD card are installed in the computer. The built-in Bluetooth function and an optional Bluetooth PC card cannot operate simultaneously. If problems persist, contact your dealer.
User’s Manual 8-22Troubleshooting■If your hard disk or other storage media contains sensitive data, you should be aware that standard deletion procedures do not remove data from the media. These standard deletion procedures include:■Selecting Delete for a target file■Putting files in the Recycle Bin and emptying the Recycle Bin■Reformatting the media■Reinstalling an operating system from the recovery CD-ROMThe procedures above delete only the initial part of the data used for file management. This makes the file invisible to the operating system, but the data can still be read by specialized utilities. If you dispose of the PC, please delete all the data on its hard disk drive. Doing so prevents unauthorized use of such data. To ensure your data is not used for unauthorized purposes, you can:■Physically destroy the hard disk drive■Use a proven specialized utility to overwrite all data■Take the hard disk drive to a professional deletion serviceAll data deletion costs will be borne by you.TOSHIBA supportIf you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance.Before you callSome problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first. Before contacting TOSHIBA, try the following:■Review troubleshooting sections in the documentation for software and peripheral devices.■If a problem occurs when you are running software applications, consult the software documentation for troubleshooting suggestions. Call the software company’s technical support for assistance.■Consult the dealer you purchased your computer and/or software from. They are your best sources for current information and support.
User’s Manual 8-23TroubleshootingWhere to writeIf you are still unable to solve the problem and suspect that it is hardware related, write to TOSHIBA at the nearest location listed below:Outside of Europe In EuropeAustraliaTOSHIBA Australia Pty. Ltd.Information Systems Division 84-92 Talavera RoadNorth Ryde N.S.W. 2113 SydneyGermany & AustriaTOSHIBA Europe (I.E.) GmbHGeschäftsbereich,Deutschland-ÖsterreichHammfelddamm 8, D-41460 Neuss, GermanyCanadaTOSHIBA of Canada Ltd.191 McNabb Street,Markham, OntarioL3R 8H2FranceTOSHIBA Systèms France S.A.7, Rue Ampère B.P. 131,92804 Puteaux CedexChinaTOSHIBA Personal Computer & Network (Shanghai) Co., Ltd.43F, Hong Kong New World Tower,No. 300 Huaihai Zhong Road,Shanghai, P. R. China 200021NetherlandsTOSHIBA Information Systems, Benelux B.V.Rivium Boulevard 41 2909 LK Capelle a/d IJsselSingaporeTOSHIBA Singapore Pte. Ltd.438B Alexandra Road #06-01Alexandra TechnoparkSingapore 119968SpainTOSHIBA Information Systems, ESPAÑAParque Empresarial San FernandoEdificio Europa, la Planta,Escalera A 28830 Madrid
User’s Manual 8-24TroubleshootingUnited States of AmericaTOSHIBA America Information Systems, Inc.9740 Irvine BoulevardIrvine, California 92618USAUnited KingdomTOSHIBA Information Systems (U.K.) Ltd.TOSHIBA CourtWeybridge Business ParkAddlestone RoadWeybridge, Surrey KT15 2ULThe Rest of EuropeTOSHIBA Europe (I.E.) GmbHGeschäftsbereich,Deutschland-ÖsterreichHammfelddamm 8, D-41460 Neuss, GermanyOutside of Europe In Europe
User’s Manual A-1Appendix ASpecificationsThis appendix summarizes the computer’s technical specifications.Physical DimensionsRefer to User’s Manual about Weight.Environmental RequirementsSize 348 (w) × 260 (d) × 39.9 (h) millimeters (not including parts that extend beyond the main body)Conditions Ambient temperature Relative humidityOperating 5°C (41°F) to 35°C (95°F) 20% to 80%Non-operating -20°C (-4°F) to 65°C (149°F) 10% to 90%Thermal Gradient 20°C per hour maximumWet-bulb temperature26°C maximum Conditions Altitude (from sea level)Operating -60 to 3,000 metersNon-operating -60 to 10,000 meters maximum
User’s Manual A-2SpecificationsPower RequirementsBuilt-in ModemAC adaptor 100-240 volts AC50 or 60 hertz (cycles per second)Computer 15 VDC5.0 amperesNetwork control unit (NCU)Type of NCU AAType of line Telephone line (analog only)Type of dialing PulseToneControl command AT commandsEIA-578 commandsMonitor function Computer’s speakerCommunication specificationsCommunication systemData: Full duplexFax: Half duplexCommunication protocolDataITU-T-Rec V.21/V.22/V.22bis/V.32(Former CCITT) /V.32bis/V.34/V.90Bell 103/212AFaxITU-T-Rec V.17/V.29/V.27ter(Former CCITT) /V.21 ch2Communication speedData transmission and reception 300/1200/2400/4800/7200/9600/12000/14400/16800/19200/21600/24000/26400/28800/31200/33600 bpsData reception only with V.9028000/29333/30666/32000/33333/34666/36000/37333/38666/40000/41333/42666/44000/45333/46666/48000/49333/50666/52000/53333/54666/56000 bpsFax2400/4800/7200/9600/12000/14400 bps
User’s Manual A-3SpecificationsNetwork control unit (NCU)Transmitting level -10 dBmReceiving level -10 to -40 dBmInput/outputimpedance600 ohms ±30%Error correcting MNP class 4 and ITU-T V.42Data compression MNP class 5 and ITU-T V.42bisPower supply +3.3V (supplied by computer)
User’s Manual B-1Appendix BDisplay Controller and ModesDisplay controllerThe display controller interprets software commands into hardware commands that turn particular parts on the screen on or off.The display controller also controls the video mode, which uses industry standard rules to govern the screen resolution and the maximum number of colors that can be displayed on screen.Software written for a given video mode will run on any computer that supports the mode.Video modeVideo mode settings are configured via the Display Properties dialog.To open the Display Properties dialog, click on the start button, select Control Panel, and from the Control Panel click on Appearance and Themes and then click on Display, and when the Display Propertiesdialog appears, click on the Settings tab.Because of the LCD’s increased resolution, lines may appear broken in DOS mode.
User’s Manual B-2Display Controller and ModesPowerMizerPowerMizer is a graphics processor installed on this computer. The performance of PowerMizer can be configured in three ways. To define the performance, select the menu options shown below:Display Property -> Settings -> Advanced -> Quadro NVS 110M tab ->Quadro NVS 110M button -> nView Display Settings -> PowerMizerThe graphics processor offers three options, Maximum Power Savings, Balanced and Maximum Performance, in each of the AC power mode and battery power mode.Figure B-1 (Multiple Monitors) and NVIDIA Quadro NVS 110MThe PowerMizer function is only available in nVIDIA models.
User’s Manual C-1Appendix CAT CommandsIn most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so.This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software.The format for entering AT commands is:ATXnwhere X is the AT command, and n is the specific value for that command. After you type in the command press Enter.Any command issued is acknowledged with a response in either text or numeric values known as result codes.All commands and command-values accepted by the modem are described in this section; any entry other than those listed results in an error.+++ Escape sequenceThe escape sequence allows the modem to exit data mode and enter on-line command mode. While in on-line command mode, you can communicate directly to your modem using AT commands. Once you finish, you can return to data mode using the ATO command.A pause, the length of which is set by Escape Guard Time (S12), must be completed after an escape sequence is entered. This pause prevents the modem from interpreting the escape sequence as data.The value of the escape sequence character may be changed using register S2.A/ Repeat last commandThis command repeats the last command string entered. Do not precede this command with an AT prefix or conclude it by pressing Enter.
User’s Manual C-2AT CommandsAAnswer commandThis command instructs the modem to go off-hook and answer an incoming call.Bn Communication standard settingThis command determines the communication standard CCITT or Bell.B0 Selects CCITT V.22 mode when the modem is at 1200 bps. B1 Selects Bell 212A when the modem is at 1200 bps (default).B15 Selects V.21 when the modem is at 300 bps.B16 Selects Bell 103J when the modem is at 300 bps (default).Result Codes:OK n=0,1,15,16ERROR OtherwiseDn DialThis command instructs the modem to dial a telephone number. Enter n(the telephone number and any modifiers) after the ATD command.Any digit or symbol (0-9, *, #, A, B, C, D) may be dialed as touch-tone digits. Characters such as spaces, hyphens, and parentheses do not count. They are ignored by the modem, but you may want to include them to make the number and modifiers easier to read.The following may be used as phone number modifiers:PPulse dialing.TTouch-tone dialing (default).,Pause during dialing. Pause for time specified in Register S8 before processing the next character in the dial string.WWait for dial tone. Modem waits for a second dial tone before processing the dial string.@Wait for quiet answer. Wait for five seconds of silence afterdialing the number. If silence is not detected, the modemsends a NO ANSWER result code back to the caller.!Hook flash. Causes the modem to go on-hook for 0.5 seconds and then return to off-hook.;Return to command mode. Causes the modem to return to command mode after dialing a number, without disconnecting the call.S=n Dial a telephone number previously stored using the &Zn=Xcommand (See &Zn=X command for more information). The range is 0-3.En Echo commandThis command controls whether or not the characters entered from your computer keyboard are displayed on your monitor (echoed) while the modem is in command mode.
User’s Manual C-3AT CommandsE0 Disables echo to the computer.E1 Enables echo to the computer (default).Result Codes:OK n=0,1ERROR OtherwiseHn Hook controlThis command instructs the modem to go on-hook to disconnect a call, or off-hook to make the phone line busy.H0 Modem goes on-hook (default).H1 Modem goes off-hook.Result Codes:OK n=0,1ERROR OtherwiseIn Request ID informationThis command displays product information about the modem.I0 Returns modem identity string and driver version number.I3 Same as I0.I9 Returns region ID in English.Result Codes:OK n=0,3,9ERROR OtherwiseLn Monitor speaker volumeThis command sets speaker volume to low, medium, or high.L0 Low volume.L1 Low volume. (Same as L0)L2 Medium volume (default).L3 High volume.Result Codes:OK n=0,1,2,3ERROR OtherwiseMn Monitor speaker modeThis command turns the speaker on or off.M0 The speaker is off.M1 The speaker is on until the modem detects the carrier signal (default).M2 The speaker is always on when modem is off-hook.M3 Speaker is on until the carrier is detected, except when dialing.
User’s Manual C-4AT CommandsResult Codes:OK n=0,1,2,3ERROR OtherwiseNn Modulation handshakeThis command controls whether or not the local modem performs a negotiated handshake at connection time with the remote modem when the communication speed of the two modems is different.N0 When originating or answering, this is for handshake only at the communication standard specified by S37 and the ATB command.N1 When originating or answering, begin the handshake at the communication standard specified by S37 and the ATB command (default).During handshake, a lower transmission speed may be selected.Result Codes:OK n=0,1ERROR OtherwiseOn Return on-line to data modeO0 Instructs the modem to exit on-line command mode and return to data mode (see AT escape sequence, +++).O1 This command issues a retrain before returning to on-line data mode.O3 This command issues a rate renegotiation before returning to on-line data mode.Result Codes:OK n=0,1,3ERROR OtherwiseP Select pulse dialingThis command configures the modem for pulse (non touch-tone) dialing. Dialed digits are pulsed until a T command or dial modifier is received. Tone dial is the default setting.Qn Result code controlResult codes are informational messages sent from the modem and displayed on your monitor. Basic result codes are OK, CONNECT, RING, NO CARRIER,andERROR. The ATQ command allows the user to turn result codes on or off.Q0 Enables modem to send result codes to the computer (default).Q1 Disables modem from sending result codes to the computer.
User’s Manual C-5AT CommandsResult Codes:OK n=0,1ERROR OtherwiseT Select tone dialingThis command instructs the modem to send DTMF tones while dialing. Dialed digits are tone dialed until a P command or dial modifier is received. This is the default setting.Vn DCE response formatThis command controls whether result codes (including call progress and negotiation progress messages) are displayed as words or their numeric equivalents.V0 Displays result codes as digits.V1 Displays result codes as text (default).Result Codes:OK n=0,1ERROR OtherwiseXn Result code selection, call progress monitoringThis command selects which result codes will be used by the modem.Command Dial tonedetectBusy signaldetectSupported Result CodeX0 Disable Disable OK, CONNECT, RING, NO CARRIER, ERRORX1 Disable Disable OK, RING, NO CARRIER, ERROR, CONNECT <RATE>X2 Enable Disable OK, RING, NO CARRIER, ERROR, NODIALTONE, CONNECT <RATE>X3 Disable Enable OK, RING, NO CARRIER, ERROR, BUSY, CONNECT <RATE>, BLACKLISTEDX4 (default) Enable Enable OK, RING, NO CARRIER, ERROR, NODIALTONE, BUSY, CONNECT <RATE>, DELAYED, BLACKLISTED, REORDER, WARBLE, CALL WAITING DETECTEDX5 Enable Enable OK, RING, NO CARRIER, ERROR, NODIALTONE, BUSY, CONNECT <RATE>, RRING, NO BONGTONE, DELAYED, BLACKLISTED, REORDER, WARBLE, CALL WAITING DETECTED
User’s Manual C-6AT CommandsDial tone detectDisabled:The modem dials a call regardless of whether it detects a dial tone.Enabled:The modem dials only upon detection of a dial tone, and disconnects the call if the dial tone is not detected within 10 seconds.Busy tone detectDisabled:The modem ignores any busy tones it receives.Enabled:The modem monitors for busy tones.Result Codes:OK n=0,1,2,3,4,5ERROR OtherwiseZn Recall stored profileThe modem performs a soft reset and restores (recalls) the configuration profile according to the parameter supplied. If no parameter is specified, zero is assumed. Either Z0 or Z1 restores the profile.Result Codes:OK n=0,1ERROR Otherwise&Cn Data Carrier Detect (DCD) controlData Carrier Detect is a signal from the modem to the computer indicating that a carrier signal is being received from a remote modem. DCD normally turns off when the modem no longer detects the carrier signal.&C0 The state of the carrier from the remote modem is ignored. DCD circuit is always on.&C1 DCD turns on when the remote modem’s carrier signal is detected, and off when the carrier signal is not detected (default).Result Codes:OK n=0,1ERROR Otherwise&Dn DTR controlThis command interprets how the modem responds to the state of the DTR signal and changes to the DTR signal.&D0 Ignore. The modem ignores the true status of DTR and treats it as always on. This should only be used if your communication software does not provide DTR to the modem&D1 If the DTR signal is not detected while in on-line data mode, the modem enters command mode, issues an OK resultcode, and remains connected.
User’s Manual C-7AT Commands&D2 If the DTR signal is not detected while in on-line data mode, the modem disconnects (default).&D3 Reset on the on-to-off DTR transition.Result Codes:OK n=0,1,2,3ERROR Otherwise&F Load factory settingsThis command loads the configuration stored and programmed at the factory. This operation replaces all of the command options and the S-register settings in the active configuration with factory values.&F Recall factory setting as active configuration.&Gn V.22bis guard tone controlThis command determines which guard tone, if any, to transmit while transmitting in the high band (answer mode). This command is only used in V.22 and V.22bis mode. This option is not used in North America and is for international use only.&G0 Guard tone disabled (default).&G1 Sets guard tone to 550 Hz.&G2 Sets guard tone to 1800 Hz.Result Codes:OK n=0,1,2ERROR Otherwise&Kn Local flow control selection&K0 Disable flow control.&K3 Enable CTS/RTS flow control (default).&K4 Enable XON/XOFF flow control.Result Codes:OK n=0,3,4ERROR Otherwise&Pn Select Pulse Dial Make/Break Ratio (WW)&P0 Selects 39% - 61% make/break ratio at 10 pulses per second.&P1 Selects 33% - 67% make/break ratio at 10 pulses per second.&P2 Selects 33% - 67% make/break ratio at 20 pulses per second.Result Codes:OK n=0,1,2ERROR Otherwise
User’s Manual C-8AT Commands&Tn Self-test commandsThese tests can help to isolate problems if you experience periodic data loss or random errors. &T0 Abort. Stops any test in progress.&T1 Local analog loop. This test verifies modem operation, as well as the connection between the modem and computer. Any data entered at the local DTE is modulated, then demodulated, and returned to the local DTE. To work properly, the modem must be off-line.Result Codes:OKn=0CONNECTn=1ERROROtherwise&V Display Current ConfigurationThis command displays the current configuration of the modem. If nonvolatile memory is supported the stored profiles are displayed as well.&V View profiles.&W Store current configurationSaves the current (active) configuration (profile), including S-Registers.The current configuration comprises a list of storable parameters illustrated in the &V command. These settings are restored to the active configuration upon receiving a Zn command or at power up. Refer to the &V command.&W Stores the current configuration.&Zn=x Store telephone numberThis command is used to store up to four dialing strings in the modem’s nonvolatile memory for later dialing. The format for the command is &Zn=“stored number” where n is the location 0-3 to which the number should be written. The dial string may contain up to 34 characters. The ATDS=n command dials using the string stored in location n.Result Codes:OK n=0, 1, 2, 3ERROR Otherwise\Nn Error control mode selectionThis command determines the type of error control used by the modem when sending or receiving data.\N0 Buffer mode. No error control.\N1 Direct mode.\N2 MNP or disconnect mode. The modem attempts to connect using MNP2-4 error control procedures. If this fails, the modem disconnects. This is also known as MNP reliable mode.
User’s Manual C-9AT Commands\N3 V.42, MNP, or buffered (default).The modem attempts to connect in V.42 error control mode. If this fails, it attempts to connect in MNP mode. If this fails, it connects in buffer mode and continues operation. This is also known as V.42/MNP auto reliable mode (same as &Q5).\N4 V.42 or disconnect. The modem attempts to connect in V.42 error control mode. If this fails, the modem disconnects.\N5 V.42. MNP or buffered (same as \N3).\N7 V.42. MNP or buffered (same as \N3).Result Codes:OK n=0,1,2,3,4,5,7ERROR Otherwise\Qn Local flow control selection\Q0 Disable flow control.\Q1 XON/XOFF software flow control.\Q3 CTS/RTS to DTE (default).Result Codes:OK n=0,1,3ERROR Otherwise\Vn Protocol result code\V0 Disable protocol result code appended to DCE speed.\V1 Enable protocol result code appended to DCE speed (default).Result Codes:OK n=0,1ERROR Otherwise%B View numbers in blacklistIf blacklisting is in effect, this command displays the numbers for which the last call attempted in the past two hours failed. The ERROR result code appears in regions that do not require blacklisting.%Cn Data compression controlThis command determines the operation of V.42bis and MNP class 5 data compression. On-line changes do not take effect until a disconnect occurs first.%C0 V.42bis/MNP 5 disabled. No data compression.%C3 V.42bis/MNP 5 enabled. Data compression enabled (default).Result Codes:OK n=0,3ERROR Otherwise
User’s Manual D-1Appendix DS-registersS-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connection fails. You can also customize certain AT commands such as the escape sequence and command line termination. The contents of the registers are changed automatically when you modify corresponding settings in your communication software. If you choose, however, you can display and edit the contents of the registers manually when the modem is in command mode. If the value is out of the acceptable range, then an error is generated.This chapter describes the settings for each S-register.S-register valuesThe format for displaying the value of an S-register is:ATSn?where n is the register number. After you type in the register press Enter.The format for modifying the value of an S-register is:ATSn=rwhere n is the register number, and r is the new register value. After you type in the register and its new value press Enter.S0 Auto answer ring numberThis register determines the number of rings the modem will count before automatically answering a call. Enter 0 (zero) if you do not want the modem to automatically answer at all. When disabled, the modem can only answer with an ATA command.Some registers vary from one country/region to another.
User’s Manual D-2S-registersRange:0-255Default:0Units:ringsS1 Ring counterThis register is read only. The value of S1 is incremented with each ring. If no ring occurs over a six-second interval, this register is cleared.Range:0-225Default:0Units:ringsS2 AT escape character (user defined)This register determines the ASCII values used for an escape sequence. The default is the + character. The escape sequence allows the modem to exit data mode and enter command mode when on-line. Values greater than 127 disable the escape sequence.Range:0-255, ASCII decimalDefault:43Units:ASCIIS3 Command line termination character (user defined)This register determines the ASCII values as the carriage return character. This character is used to end command lines and result codes.Range:0-127, ASCII decimalDefault:13 (carriage return)Units:ASCIIS4 Response formatting character (user defined)This register determines the ASCII value used as the line feed character. The modem uses a line feed character in command mode when it responds to the computer.Range:0-127, ASCII decimalDefault:10 (line feed)Units:ASCII
User’s Manual D-3S-registersS5 Command line editing character (user defined)This register sets the character recognized as a backspace and pertains to asynchronous only. The modem will not recognize the backspace character if it is set to a value that is greater than 32 ASCII. This character can be used to edit a command line. When the echo command is enabled, the modem echoes back to the local DTE the backspace character, an ASCII space character, and a second backspace character. This means a total of three characters are transmitted each time the modem processes the backspace character.Range:0-127, ASCII decimalDefault:8 (backspace)Units:ASCIIS6 Wait before dialingThis register sets the length of time, in seconds, that the modem must wait (pause) after going off-hook before dialing the first digit of the telephone number. The modem always pauses for a minimum of two seconds, even if the value of S6 is less that two seconds. The wait for dial tone call progress feature (W dial modifier in the dial string) will override the value in register S6. This operation, however, may be affected by some ATX options according to country/region restrictions. In some countries/regions, S6 will set dial tone detect time.Range:3-255Default:3Units:secondsS7 Connection completion time-outThis register sets the time, in seconds, that the modem must wait before hanging up because carrier is not detected. The timer is started when the modem finishes dialing (originate), or goes off-hook (answer). In originate mode, the timer is reset upon detection of an answer tone if allowed by county restriction. The timer also specifies the wait for silence time for the @ dial modifier in seconds. S7 is not associated with the W dial modifier.Range:1-255Default:50Units:seconds
User’s Manual D-4S-registersS8 Comma pause timeThis register sets the time, in seconds, that the modem must pause when it encounters a comma (,) in the dial command string. In some countries/regions, S8 will set both wait before dialing and comma pause time.Range:0-255Default:2Units:secondsS11 DTMF dialing speedThis register determines the dialing speed which is prefixed for each country/region. Range:50-255Default:95Units:.001 secondsS12 Escape guard timeThis register sets the value (in 20 millisecond increments) for the required pause after the escape sequence.Range:0-255Default:50Units:.02 seconds
User’s Manual D-5S-registersS37 Dial line rateS37 = 0 (default) maximum modem speedS37 = 1 reservedS37 = 2 1200/75 bpsS37 = 3 300 bpsS37 = 4 reservedS37 = 5 1200 bpsS37 = 6 2400 bpsS37 = 7 4800 bpsS37 = 8 7200 bpsS37 = 9 9600 bpsS37 = 10 12000 bpsS37 = 11 14400 bpsS37 = 12 16800 bpsS37 = 13 19200 bpsS37 = 14 21600 bpsS37 = 15 24000 bpsS37 = 16 26400 bpsS37 = 17 28800 bpsS37 = 18 31200 bpsS37 = 19 33600 bps
User’s Manual D-6S-registersAT command set result codesThe following table shows the result codes.The result code summaryResult Code Numeric DescriptionOK 0 Command executedCONNECT 1 Modem connected to lineRING 2 A ring signal has been detectedNO CARRIER 3 Modem lost carrier signal, or does not detect carrier signal, or does not detect answer toneERROR 4 Invalid commandCONNECT 1200 EC*15 Connection at 1200 bpsNO DIAL TONE 6 No dial tone detectedBUSY 7 Busy signal detectedNO ANSWER 8 No quiet answerCONNECT 2400 EC*110 Connection at 2400 bpsCONNECT 4800 EC*111 Connection at 4800 bpsCONNECT 9600 EC*112 Connection at 9600 bpsCONNECT 14400 EC*113 Connection at 14400 bpsCONNECT 19200 EC*114 Connection at 19200 bpsCONNECT 7200 EC*124 Connection at 7200 bpsCONNECT 12000 EC*125 Connection at 12000 bpsCONNECT 16800 EC*186 Connection at 16800 bpsCONNECT 300 EC*140 Connection at 300 bpsCONNECT 21600 EC*155 Connection at 21600 bpsCONNECT 24000 EC*156 Connection at 24000 bpsCONNECT 26400 EC*157 Connection at 26400 bpsCONNECT 28800 EC*158 Connection at 28800 bpsCONNECT 31200 EC*159 Connection at 31200 bps
User’s Manual D-7S-registers*1: EC only appears when the Extended Result Codes configuration option is enabled. EC is replaced by one of the following symbols, depending upon the error control method used:V.42bis - V.42 error control and V.42bis data compression.V.42 - V.42 error control only.MNP 5 - MNP class 4 error control and MNP class 5 data compression.MNP 4 - MNP class 4 error control only.NoEC - No error control protocol.*2: In some countries/regions, these result codes may not appear.CONNECT 33600 EC*160 Connection at 33600 bpsDELAYED*288 Delay is in effect for the dialed numberBLACKLISTED*289 Dialed number is blacklistedBLACKLIST FULL*290 Blacklist is full
User’s Manual E-1Appendix EV.90The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56kbps (kilobits per second) when connected to an Internet service provider that supports V.90. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably. Therefore, many users will experience throughput in the range of 28-50kbps under normal telephone line conditions. Upstream data flows at the V.34 rate.V.90 modeV.90 rates can be achieved only when one V.90-capable host modem is connected to another. The TOSHIBA Internal modem will select automatically V.34 if the remote modem lacks V.90 capability or if a combination of network and/or phone line conditions prevent V.90 connection.Function Transmission speedData V.90 From 56kbps (maximum) to 28kbps (minimum)Reception only
User’s Manual E-2V.90Table E-1 Result codes for a V.90 connectionNo. Result code Description70 CONNECT 32000 EC* Connection at 32000 bps 72 CONNECT 36000 EC* Connection at 36000 bps 74 CONNECT 40000 EC* Connection at 40000 bps 76 CONNECT 44000 EC* Connection at 44000 bps 78 CONNECT 48000 EC* Connection at 48000 bps 80 CONNECT 52000 EC* Connection at 52000 bps 82 CONNECT 56000 EC* Connection at 56000 bps 100 CONNECT 28000 EC* Connection at 28000 bps 101 CONNECT 29333 EC* Connection at 29333 bps 102 CONNECT 30666 EC* Connection at 30666 bps 103 CONNECT 33333 EC* Connection at 33333 bps 104 CONNECT 34666 EC* Connection at 34666 bps 105 CONNECT 37333 EC* Connection at 37333 bps 106 CONNECT 38666 EC* Connection at 38666 bps 107 CONNECT 41333 EC* Connection at 41333 bps 108 CONNECT 42666 EC* Connection at 42666 bps 109 CONNECT 45333 EC* Connection at 45333 bps 110 CONNECT 46666 EC* Connection at 46666 bps 111 CONNECT 49333 EC* Connection at 49333 bps 112 CONNECT 50666 EC* Connection at 50666 bps 113 CONNECT 53333 EC* Connection at 53333 bps 114 CONNECT 54666 EC* Connection at 54666 bps
User’s Manual E-3V.90 * EC stands for the Error Control method, which appears only when the extended result codes configuration option is enabled. EC is replaced by one of the following symbols, depending on the error control method used.AT CommandV42bis V.42 error control and V.42bis data compressionV42 V.42 error control onlyNoEC No error control protocol-V90=* V.90 Dial Line Rate-V90 sets the maximum V.90 downstream that the modem attempts to connect.-V90=0 V.90 disabled-V90=1 V.90 enabled: automatic speed selection - maximum modem speed (default)
User’s Manual F-1Appendix FWireless LANCard SpecificationsForm Factor PCI Express Mini CardCompatibility ■IEEE 802.11 Standard for Wireless LANS■Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The ‘Wi-Fi CERTIFIED’ logo is a certification mark of the Wi-Fi Alliance. Network OperatingSystem■Microsoft Windows® NetworkingMedia AccessProtocol■CSMA/CA (Collision Avoidance) with Acknowledgment (ACK)Data Rate ■Theoretical maximum speed: 54Mbps (IEEE802.11a/IEEE802.11g: 11b/g, 11a/b/g combo type)■Theoretical maximum speed: 11Mbps (IEEE802.11b)
User’s Manual F-2Wireless LANRadio CharacteristicsRadio Characteristics of Wireless LAN Cards may vary according to:■Country/region where the product was purchased■Type of productWireless communication is often subject to local radio regulations. Although Wireless LAN wireless networking products have been designed for operation in the license-free 2.4GHz and 5GHz band, local radio regulations may impose a number of limitations to the use of wireless communication equipment. The range of the wireless signal is related to the transmit rate of the wireless communication. Communications at lower transmit range may travel larger distances.■The range of your wireless devices can be affected when the antennas are placed near metal surfaces and solid high-density materials.■Range is also impacted due to "obstacles" in the signal path of the radio that may either absorb or reflect the radio signal.Refer to the sheet “Information to the User” for regulatory information that may apply in your country/region.R-F Frequency ■Band 5GHz (5150-5850 MHz) (Revision A)■Band 2.4GHz (2400-2483.5 MHz) (Revision B, G)ModulationTechnique ■DSSS-CCK, DSSS-DQPSK, DSSS-DBPSK(Revision B)■OFDM-BPSK, OFDM-QPSK, OFDM-16QAM, OFDM-64QAM (Revision A, G)
User’s Manual F-3Wireless LANSupported Frequency Sub-bandsSubject to the radio regulations that apply in the countries/regions, your Wireless LAN card may support a different set of 5 GHz/2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in the countries/regions.Wireless IEEE 802.11 Channels Sets (Revision B and G)*1 Factory-set default channels*2 Refer to the sheet Approved Countries/Regions for use for the countries/regions that in which these channels can be used. When installing Wireless LAN cards, the channel configuration is managed as follows:■For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless LAN card will automatically start operation at the channel identified by the Wireless LAN Access Point. When roaming between different access points the station can dynamically switch to another channel if required.Frequency Range Channel ID 2400-2483.5 MHz12412224173242242427524326243772442824479245210 2457*111 246212 2467*213 2472*2
User’s Manual F-4Wireless LAN■For Wireless LAN cards installed in wireless clients that operating in a peer-to-peer mode, the card will use the default channel 10.■In a Wireless LAN Access Point, the Wireless LAN card will use the factory-set default channel (printed in bold), unless the LAN Administrator selected a different channel when configuring the Wireless LAN Access Point device.Wireless IEEE 802.11 Channels Sets (Revision A)Frequency Range Channel ID     5150-5850 MHz 36 518040 520044 522048 524052 526056 528060 530064 5320100 5500104 5520108 5540112 5560116 5580120 5600124 5620128 5640132 5660136 5680140 5700
User’s Manual F-5Wireless LAN149 5745153 5765157 5785161 5805165 5825
User’s Manual G-1Appendix GBluetooth wireless technology InteroperabilityBluetooth® Cards from TOSHIBA are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to:■Bluetooth Specification Ver2.0+EDR, as defined and approved by The Bluetooth Special Interest Group.■Logo certification with Bluetooth wireless technology as defined by The Bluetooth Special interest Group.
User’s Manual G-2Bluetooth wireless technology Interoperability■Bluetooth wireless technology is a new innovative technology, and TOSHIBA has not confirmed compatibility of its Bluetooth® products with all computers and/or equipment using Bluetooth wireless technology other than TOSHIBA portable computers.Always use Bluetooth® Cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA PC product support on Web sitehttp://www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe orhttp://www.pc.support.global.toshiba.com in the United States for more information.■When you use Bluetooth® Cards from TOSHIBA close to 2.4 GHz Wireless LAN devices, Bluetooth transmissions might slow down or cause errors. If you detect certain interference while you use Bluetooth® Cards from TOSHIBA, always change the frequency, move your computer to the area outside of the interference range of 2.4 GHz Wireless LAN devices (40 meters/43.74 yards or more) or stop transmitting from your computer. Please contact TOSHIBA PC product support on Web site http://www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe orhttp://www.pc.support.global.toshiba.com in the United States for more information.■Bluetooth® and Wireless LAN devices operate within the same radio frequency range and may interfere with one another. If you use Bluetooth® and Wireless LAN devices simultaneously, you may occasionally experience a less than optimal network performance or even lose your network connection.If you should experience any such problem, immediately turn off either one of your Bluetooth® or Wireless LAN. Please contact TOSHIBA PC product support on web site http://www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe orhttp://www.pc.support.global.toshiba.com in the United States for more information.
User’s Manual G-3Bluetooth wireless technology InteroperabilityBluetooth wireless technology and your HealthThe products with Bluetooth wireless technology, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by devices with Bluetooth wireless technology however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.Because products with Bluetooth wireless technology operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Bluetooth wireless technology is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.In some situations or environments, the use of Bluetooth wireless technology may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include:■Using the equipment with Bluetooth wireless technology on board of airplanes, or■In any other environment where the risk of interference to other devices or services is perceived or identified as harmful.If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment (e.g. airports), you are encouraged to ask for authorization to use the device with Bluetooth wireless technology prior to turning on the equipment.Regulatory statementsGeneralThis product complies with any mandatory product specification in any country/region where the product is sold. In addition, the product complies with the following.European Union (EU) and EFTAThis equipment complies with the R&TTE directive 1999/5/EC and has been provided with the CE mark accordingly.Canada - Industry Canada (IC)This device complies with RSS 210 of Industry Canada.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.
User’s Manual G-4Bluetooth wireless technology InteroperabilityL ‘ utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’ utilisateur du dispositif doit étre prét à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.The term “IC” before the equipment certification number only signifies that the Industry Canada technical specifications were met.USA-Federal Communications Commission (FCC)This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:■Reorient or relocate the receiving antenna■Increase the distance between the equipment and the receiver.■Connect the equipment to outlet on a circuit different from that to which the receiver is connected.■Consult the dealer or an experienced radio/TV technician for help.TOSHIBA is not responsible for any radio or television interference caused by unauthorized modification of the devices included with this Bluetooth®Card from TOSHIBA, or the substitution or attachment of connecting cables and equipment other than specified by TOSHIBA.The correction of interference caused by such unauthorized modification, substitution or attachment will be the responsibility of the user.
User’s Manual G-5Bluetooth wireless technology InteroperabilityCaution: Exposure to Radio Frequency RadiationThe radiated output power of the Bluetooth® Card from TOSHIBA is far below the FCC radio frequency exposure limits. Nevertheless, the Bluetooth® Card from TOSHIBA shall be used in such a manner that the potential for human contact during normal operation is minimized. The antenna(s) used in this device are located at the upper edge of the LCD screen, and this device has been tested as portable device as defined in Section 2.1093 of FCC rules when the LCD screen is rotated 180 degree and covered the keyboard area.  In addition, Bluetooth has been tested with Wireless LAN transceiver for co-location requirements. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada's website www.hc-sc.gc.ca/rpb.TaiwanArticle 12 Without permission granted by the DGT, any company, enterprise, or user is not allowed to change frequency, enhance transmitting power or alter original characteristic as well as performance to an approved low power radio-frequency devices.Article 14 The low power radio-frequency devices shall not influence aircraft security and interfere legal communications; If found, the user shall cease operating immediately until no interference is achieved.The said legal communications means radio communications is operated in compliance with the Telecommunications Act.The low power radio-frequency devices must be susceptible with the interference from legal communications or ISM radio wave radiated devices.Using Bluetooth® Card from TOSHIBA equipment in JapanIn Japan, the frequency bandwidth of 2,400 - 2,483.5 MHz for second generation low-power data communication systems such as this equipment overlaps that of mobile object identification systems (premises radio station and specified low-power radio station).1. StickerPlease put the following sticker on computer incorporating this product.
User’s Manual G-6Bluetooth wireless technology Interoperability2. IndicationThe indication shown below appears on this equipment.(1) 2.4 : This equipment uses a frequency of 2.4 GHz.(2) FH : This equipment uses FH-SS modulation.(3) 1: The interference range of this equipment is less than 10 m.(4)   This equipment uses a frequency bandwidth from2,400 MHz to 2,483.5 MHz. It is impossible to avoid the band of mobile object identification systems.3. TOSHIBA Direct PCMonday - Friday:  10:00-17:00Toll Free Tel :  0120-15-1048Direct Dial:  03-3457-4850FAX :  03-3457-4868The frequency bandwidth of this equipment may operate within the same range as industrial devices, scientific devices, medical devices, microwave ovens, licensed radio stations and non-licensed specified low-power radio stations for mobile object identification systems (RFID) used in factory production lines (Other Radio Stations).1.  Before using this equipment, ensure that it does not interfere with any of the equipment listed above.2.  If this equipment causes RF interference to other radio stations, promptly change the frequency being used, change the location of use, or turn off the source of emissions.3.  Contact TOSHIBA Direct PC if you have problems with interference caused by this product to Other Radio Stations.
User’s Manual G-7Bluetooth wireless technology InteroperabilityDevice AuthorizationThis device obtains the Technical Conditions Compliance Approval, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Telecommunications Business Law.The Name of the radio equipment: EYXF3CSJAPAN APPROVALS INSTITUTE FOR TELECOMMUNICATIONS EQUIPMENTApproval Number: D05-0074001The following restrictions apply:Do not disassemble or modify the device.Do not install the embedded wireless module into other device.
User’s Manual H-1Appendix HAC Power Cord and ConnectorsThe power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications:Certification agenciesLength: Minimum 2 metersWire size: Minimum 0.75 mm2Current rating: Minimum 2.5 amperesVoltage rating: 125 or 250 VAC (depending on country/region’s power standards)U.S. and Canada: UL listed and CSA certifiedNo. 18 AWG, Type SVT or SPT-2Australia: ASJapan: DENANHOEurope:Austria: OVE Italy: IMQBelgium: CEBEC The Netherlands: KEMADenmark: DEMKO Norway: NEMKO
User’s Manual H-2AC Power Cord and ConnectorsIn Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV-F.For the United States and Canada, two pin plug configuration must be a 2-15P (250V) or 1-15P (125V) and three pin plug configuration must be 6-15P (250V) or 5-15P (125V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical Code Part II.The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia and Europe.Finland: FIMKO Sweden: SEMKOFrance: LCIE Switzerland: SEVGermany: VDE United Kingdom: BSIUSA United KingdomAS approved Approved by theBS approvedUL approvedCSA approvedappropriate agencyAustralia EuropeCanada
User’s Manual I-1Appendix ITOSHIBA Anti-theft Protection Timer This feature allows you to set up a timer-activated BIOS password that will prevent unauthorised system access in the event of theft.When the time limit is exceeded, you are required to provide the Password or fingerprint authentication for the BIOS and Hard Disk Drive to gain access to the system.To set permissions and limits for the TOSHIBA Anti-theft Protection Timer please use the TOSHIBA Password Utility.The settings can only be activated or modified by a user with supervisor authority. If the supervisor password is not set, click on the Set button in Supervisor Password from the supervisor tab in TOSHIBA Password Utility and set the password on the dialog screen that appears.Then, click on the Set button in TOSHIBA Anti-theft Protection Timer.Take the following action if the set limit is exceeded.■If the Supervisor Password is registered but the User Password is not, enter the Supervisor Password to boot up the computer.■If both the Supervisor Password and the User Password are registered, enter either the Supervisor Password, the User Password or the fingerprint authentication to boot up the computer.■The limit counts the number of days from the last time Windows is logged on till the next time the computer is booted up. The range can be set from 1 to 28 days.■Authentication is required if the computer’s clock is significantly modified.■If the Supervisor Password is deleted, this function becomes disabled.
User’s Manual J-1Appendix JLegal FootnotesThis chapter states the Legal Footnotes information applicable to TOSHIBA computers. In the text in this manual, *XX is used to show which Legal Footnotes description is related to TOSHIBA computers.Description(s) related to this computer are marked with a blue *XX in this manual. Clicking on *XX will display the related description.Non-applicable Icons*1Certain notebook chassis are designed to accommodate all possible configurations for an entire product series. Therefore, please be aware that your selected model may not have all the features and specifications corresponding to all of the icons or switches shown on the notebook chassis.CPU*2Central Processing Unit ("CPU") Performance Legal Footnotes.CPU performance in your computer product may vary from specifications under the following conditions:■use of certain external peripheral products■use of battery power instead of AC power ■use of certain multimedia, computer generated graphics or video       applications■use of standard telephone lines or low speed network connections■use of complex modeling software, such as high end computer aided design applications■use of several applications or functionalities simultaneously■use of computer in areas with low air pressure (high altitude >1,000 meters or >3,280 feet above sea level)
User’s Manual J-2Legal Footnotes■use of computer at temperatures outside the range of 5°C to 30°C (41°F to 86°F) or >25°C (77°F) at high altitude (all temperature references are approximate and may vary depending on the specific computer model - please refer to your PC documentation or visit the Toshiba website at www.pcsupport.toshiba.com for details).CPU performance may also vary from specifications due to design configuration.Under some conditions, your computer product may automatically shut-down. This is a normal protective feature designed to reduce the risk of lost data or damage to the product when used outside recommended conditions. To avoid risk of lost data, always make back-up copies of data by periodically storing it on an external storage medium. For optimum performance, use your computer product only under recommended conditions. Read additional restrictions in your product documentation. Contact Toshiba technical service and support, refer to TOSHIBA supportsection in Chapter 8 Troubleshooting for more information.Memory (Main System)*3Part of the main system memory may be used by the graphics system for graphics performance and therefore reduce the amount of main system memory available for other computing activities. The amount of main system memory allocated to support graphics may vary depending on the graphics system, applications utilized, system memory size and other factors. For PC's configured with 4 GB of system memory, the full system memory space for computing activities will be considerably less and will vary by model and system configuration.Battery Life*4Battery life may vary considerably depending on product model, configuration, applications, power management settings and features utilized, as well as the natural performance variations produced by the design of individual components. Published battery life numbers are achieved on select models and configurations tested by Toshiba at the time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power. After going through many charge and discharge cycles, the battery will lose its ability to perform at maximum capacity and will need to be replaced. This is a normal phenomenon for all batteries. To purchase a new battery pack, see the accessories information that is shipped with your computer.
User’s Manual J-3Legal FootnotesHard Disk Drive (HDD) Capacity*51 Gigabyte (GB) means 109 = 1,000,000,000 bytes using powers of 10. The computer operating system, however, reports storage capacity using powers of 2 for the definition of 1 GB = 230 = 1,073,741,824 bytes, and therefore shows less storage capacity. Available storage capacity will also be less if the product includes one or more pre-installed operating systems, such as Microsoft Windows and/or pre-installed software applications, or media content. Actual formatted capacity may vary.LCD*6Over a period of time, and depending on the usage of the computer, the brightness of the LCD screen will deteriorate. This is an intrinsic characteristic of LCD technology.Maximum brightness is only available when operating in AC power mode. The screen will dim when the computer is operated on battery power and you may not be able to increase the brightness of the screen.Graphics Processor Unit ("GPU")*7Graphics processor unit ("GPU") performance may vary depending on product model, design configuration, applications, power management settings and features utilized. GPU performance is only optimized when operating in AC power mode and may decrease considerably when operating in battery power mode.Wireless LAN*8The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configurations.[54Mbps is the theoretical maximum speed under the IEEE802.11 (a/b/g) standard.] The actual transmission speed will be lower than the theoretical maximum speed.Copy Protection*9Copy protection technology included in certain media may prevent or limit recording or viewing of the media.Images*10All images are simulated for purposes of illustration.
User’s Manual Glossary-1GlossaryThe terms in this glossary cover topics related to this manual. Alternate naming is included for reference.AbbreviationsAC:  alternating currentAGP:  accelerated graphics portANSI:  American National Standards InstituteAPM:  advanced power managerASCII:  American Standard Code for Information InterchangeBIOS:  basic input output systemCD-ROM:  Compact Disc-Read Only Memory CD-RW:  Compact Disc-ReWritableCMOS:  complementary metal-oxide semiconductorCPU:  central processing unitCRT:  cathode ray tubeDC:  direct currentDDC:  display data channelDMA:  direct memory accessDOS:  disk operating systemDVD: digital versatile discDVD-R:  Digital Versatile Disc-RecordableDVD-RAM:  Digital Versatile Disc-Random Access MemoryDVD-R DL: Digital Versatile Disc Recordable Dual LayerDVD-ROM:  Digital Versatile Disc-Read Only MemoryDVD-RW:  Digital Versatile Disc-ReWritableDVD+R DL:  Digital Versatile Disc Recordable Double LayerECP:  extended capabilities portFDD:  floppy disk driveFIR:  fast infraredHDD:  hard disk driveIDE:  integrated drive electronicsI/O:  input/outputIrDA:  Infrared Data Association
User’s Manual Glossary-2GlossaryIRQ:  interrupt requestKB:  kilobyteLCD:  liquid crystal displayLED:  light emitting diodeLSI:  large scale integrationMB: megabyteMS-DOS: Microsoft Disk Operating SystemOCR:  optical character recognition (reader)PCB:  printed circuit boardPCI: peripheral component interconnectRAM:  random access memoryRGB:  red, green, and blueROM:  read only memoryRTC:  real time clockSCSI:  small computer system interfaceSIO:  serial input/outputSXGA+:  super extended graphics array plusTFT:  thin-film transistorUART:  universal asynchronous receiver/transmitterUSB:  Universal Serial BusUXGA:  ultra extended graphics arrayVESA:  Video Electronic Standards AssociationVGA:  video graphics array VRT:  voltage reduction technologyWXGA:  wide extended graphics arrayXGA:  extended graphics arrayAadaptor:  A device that provides an interface between two dissimilar electronic devices. For example, the AC adaptor modifies the power from a wall outlet for use by the computer. This term also refers to the add-in circuit cards that control external devices, such as video monitors and magnetic tape devices. allocate:  To assign a space or function for a specific task.alphanumeric:  Keyboard characters including letters, numbers and other symbols, such as punctuation marks or mathematical symbols.alternating current (AC):  Electric current that reverses its direction of flow at regular intervals. analog signal:  A signal whose characteristics such as amplitude and frequency vary in proportion to (are an analog of) the value to be transmitted. Voice communications are analog signals.
User’s Manual Glossary-3GlossaryANSI:  American National Standards Institute. An organization established to adopt and define standards for a variety of technical disciplines. For example, ANSI defined the ASCII standard and other information processing requirements.antistatic:  A material used to prevent the buildup of static electricity.application:  A group of programs that together are used for a specific task such as accounting, financial planning, spreadsheets, word processing and games.ASCII:  American Standard Code for Information Interchange. ASCII code is a set of 256 binary codes that represent the most commonly used letters, numbers, and symbols.async:  Short for asynchronous.asynchronous:  Lacking regular time relationship. As applied to computer communications, asynchronous refers to the method of transmitting data that does not require a steady stream of bits to be transmitted at regular time intervals.Bbackup:  A duplicate copy of files kept as a spare in case the original is destroyed.batch file:  A file that can be executed from the system prompt containing a sequence of operating system commands or executable files. binary:  The base two number system composed of zeros and ones (off or on), used by most digital computers. The right-most digit of a binary number has a value of 1, the next a value of 2, then 4, 8, 16, and so on. For example, the binary number 101 has a value of 5. See alsoASCII.BIOS:  Basic Input Output System. The firmware that controls data flow within the computer. See also firmware.bit:  Derived from "binary digit," the basic unit of information used by the computer. It is either zero or one. Eight bits is one byte. See alsobyte.board:  A circuit board. An internal card containing electronic components, called chips, which perform a specific function or increase the capabilities of the system.boot:  Short for bootstrap. A program that starts or restarts the computer. The program reads instructions from a storage device into the computer’s memory.bps:  Bits per second. Typically used to describe the data transmission speed of a modem.buffer:  The portion of the computer’s memory where data is temporarily stored. Buffers often compensate for differences in the rate of flow from one device to another.bus:  An interface for transmission of signals, data or electric power.
User’s Manual Glossary-4Glossarybyte:  The representation of a single character. A sequence of eight bits treated as a single unit; also the smallest addressable unit within the system.Ccache memory:  High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory. The next time the CPU needs that same data, it looks for it in the cache memory rather than the main memory, which saves time. The computer has two cache levels. Level one is incorporated into the processor and level two resides in external memory.capacity:  The amount of data that can be stored on a magnetic storage device such as a floppy disk or hard disk. It is usually described in terms of kilobytes (KB), where one KB = 1024 bytes and megabytes (MB), where one MB = 1024 KB.card:  Synonym for board. See board.CardBus:  An industry standard bus for 32-bit PC cards.CD-ROM:  A Compact Disc-Read Only Memory is a high capacity disc that can be read from but not written to. The CD-ROM drive uses a laser, rather than magnetic heads, to read data from the disc.CD-R:  A Compact Disc-Recordable disc can be written once and read many times. See also CD-ROM.CD-RW:  A Compact Disc-ReWritable disc can be rewritten many times. See also CD-ROM.character:  Any letter, number, punctuation mark, or symbol used by the computer. Also synonymous with byte.chassis:  The frame containing the computer.chip:  A small semiconductor containing computer logic and circuitry for processing, memory, input/output functions and controlling other chips.CMOS: Complementary Metal-Oxide Semiconductor. An electronic circuit fabricated on a silicon wafer that requires very little power. Integrated circuits implemented in CMOS technology can be tightly packaged and are highly reliable.cold start:  Starting a computer that is currently off (turning on the power).COM1, COM2, COM3 and COM4:  The names assigned to the serial and communication ports.commands:  Instructions you enter at the terminal keyboard that direct the actions of the computer or its peripheral devices.communications:  The means by which a computer transmits and receives data to and from another computer or device. See parallel interface; serial interface.
User’s Manual Glossary-5Glossarycompatibility:  1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred.2) the ability of one device to connect to or communicate with another system or component.components:  Elements or parts (of a system) which make up the whole (system).computer program:  A set of instructions written for a computer that enable it to achieve a desired result.computer system:  A combination of hardware, software, firmware, and peripheral components assembled to process data into useful information.configuration:  The specific components in your system (such as the terminal, printer, and disk drives) and the settings that define how your system works. You use the HW Setup program to control your system configuration.control keys:  A key or sequence of keys you enter from the keyboard to initiate a particular function within a program.controller:  Built-in hardware and software that controls the functions of a specific internal or peripheral device (e.g. keyboard controller).co-processor:  A circuit built into the processor that is dedicated to intensive math calculations.CPS:  Characters Per Second. Typically used to indicate the transmission speed of a printer.CPU:  Central Processing Unit. The portion of the computer that interprets and executes instructions.CRT:  Cathode Ray Tube. A vacuum tube in which beams projected on a fluorescent screen-producing luminous spots. An example is the television set.cursor:  A small, blinking rectangle or line that indicates the current position on the display screen.Ddata:  Information that is factual, measurable or statistical that a computer can process, store, or retrieve.data bits:  A data communications parameter controlling the number of bits (binary digits) used to make up a byte. If data bits = 7 the computer can generate 128 unique characters. If data bits = 8 the computer can generate 256 unique characters.DC:  Direct Current. Electric current that flows in one direction. This type of power is usually supplied by batteries.default:  The parameter value automatically selected by the system when you or the program do not provide instructions. Also called a preset value.
User’s Manual Glossary-6Glossarydelete:  To remove data from a disk or other data storage device. Synonymous with erase.device driver:  A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on.dialog box:  A window that accepts user input to make system settings or record other information.disk drive:  The device that randomly accesses information on a disk and copies it to the computer’s memory. It also writes data from memory to the disk. To accomplish these tasks, the unit physically rotates the disk at high speed past a read-write head.disk storage:  Storing data on magnetic disk. Data is arranged on concentric tracks much like a phonograph record.display:  A CRT, LCD, or other image producing device used to view computer output.documentation:  The set of manuals and/or other instructions written for the users of a computer system or application. Computer system documentation typically includes procedural and tutorial information as well as system functions. DOS:  Disk Operating System. See operating system.driver:  A software program, generally part of the operating system, that controls a specific piece of hardware (frequently a peripheral device such as a printer or mouse).DVD-R (+R, -R):  A Digital Versatile Disc-Recordable disk can be written once and read many times. The DVD-R drive uses a laser to read data from the disc.DVD-RAM:  A Digital Versatile Disc-Random Access Memory is a high-capacity, high performance disc that lets you store large volumes of data. The DVD-ROM drive uses a laser to read data from the disc. DVD-R DL: A disc having two layers on one side with the DVD-R storage capacity about 1.8 times larger than before. The DVD-RW drive uses a laser to read data from the disc.DVD-ROM:  A Digital Versatile Disc-Read Only Memory is a high capacity, high performance disc suitable for play back of video and other high-density files. The DVD-ROM drive uses a laser to read data from the disc. DVD-RW (+RW, -RW):  A Digital Versatile Disc-ReWritable disc can be rewritten many times.DVD+R DL: A disc having two layers on one side with the DVD+R storage capacity about 1.8 times larger than before. The DVD-RW drive uses a laser to read data from the disc.
User’s Manual Glossary-7GlossaryEecho:  To send back a reflection of the transmitted data to the sending device. You can display the information on the screen, or output it to the printer, or both. When a computer receives back data it transmitted to a CRT (or other peripheral device) and then retransmits the data to printer, the printer is said to echo the CRT.erase:  See delete.escape:  1) A code (ASCII code 27), signaling the computer that what follows are commands; used with peripheral devices such as printers and modems. 2) A means of aborting the task currently in progress.escape guard time:  A time before and after an escape code is sent to the modem which distinguishes between escapes that are part of the transmitted data, and escapes that are intended as a command to the modem.execute:  To interpret and execute an instruction.Extended Capability Port:  An industry standard that provides a data buffer, switchable forward and reverse data transmission, and run length encoding (RLE) support.Ffast infrared:  An industry standard that enables cableless infrared serial data transfer at speeds of up to 4 Mbps. file:  A collection of related information; a file can contain data, programs, or both.fingerprint sensor: The fingerprint sensor compares and analyzes the unique characteristics in a fingerprint.firmware:  A set of instructions built into the hardware which controls and directs a microprocessor’s activities.floppy disk:  A removable disk that stores magnetically encoded data. floppy disk drive (FDD):  An electromechanical device that reads and writes to floppy disks.Fn-esse:  A TOSHIBA utility that lets you assign functions to hot keys.folder:  An icon in Windows used to store documents or other folders.format:  The process of readying a blank disk for its first use. Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk.function keys:  The keys labeled F1 through F12 that tell the computer to perform certain functions.Ggigabyte (GB):  A unit of data storage equal to 1024 megabytes. See alsomegabyte.
User’s Manual Glossary-8Glossarygraphics:  Drawings, pictures, or other images, such as charts or graphs, to present information.Hhard disk:  A non-removable disk usually referred to as drive C. The factory installs this disk and only a trained engineer can remove it for servicing. Also called fixed disk.hard disk drive (HDD):  An electromechanical device that reads and writes a hard disk. See also hard disk.hardware:  The physical electronic and mechanical components of a computer system: typically, the computer itself, external disk drives, etc. See also software and firmware.hertz: A unit of wave frequency that equals one cycle per second.hexadecimal:  The base 16 numbering system composed of the digits 0 through 9 and the letters A, B, C, D, E, and F.host computer:  The computer that controls, regulates, and transmits information to a device or another computer.hot key:  The computer’s feature in which certain keys in combination with the extended function key, Fn, can be used to set system parameters, such as speaker volume.HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components.Iicon:  A small graphic image displayed on the screen or in the indicator panel. In Windows, an icon represents an object that the user can manipulate.i.LINK (IEEE1394):  This port enables high-speed data transfer directly from external devices such as digital video cameras.infrared port:  A cableless communications port capable of using infrared signals to send serial data.input: The data or instructions you provide to a computer, communication device or other peripheral device from the keyboard or external or internal storage devices. The data sent (or output) by the sending computer is input for the receiving computer.instruction:  Statements or commands that specify how to perform a particular task.interface:  1) Hardware and/or software components of a system used specifically to connect one system or device to another. 2) To physically connect one system or device to another to exchange information. 3) The point of contact between user, the computer, and the program, for example, the keyboard or a menu.interrupt request:  A signal that gives a component access to the processor.
User’s Manual Glossary-9GlossaryI/O:  Input/output. Refers to acceptance and transfer of data to and from a computer.I/O devices:  Equipment used to communicate with the computer and transfer data to and from it.IrDA 1.1:  An industry standard that enables cableless infrared serial data transfer at speeds of up to 4 Mbps. Jjumper:  A small clip or wire that allows you to change the hardware characteristics by electrically connecting two points of a circuit.KK:  Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power. See also byte and kilobyte.KB: See kilobyte.keyboard:  An input device containing switches that are activated by manually pressing marked keys. Each keystroke activates a switch that transmits a specific code to the computer. For each key, the transmitted code is, in turn, representative of the (ASCII) character marked on the key.kilobyte (KB):  A unit of data storage equal to 1024 bytes. See also byte and megabyte.Llevel 2 cache:  See cache.Light Emitting Diode (LED):  A semiconductor device that emits light when a current is applied.Liquid Crystal Display (LCD):  Liquid crystal sealed between two sheets of glass coated with transparent conducting material. The viewing-side coating is etched into character forming segments with leads that extend to the edge of the glass. Applying a voltage between the glass sheets alters the brightness of the liquid crystal.LSI:  Large Scale Integration.   1) A technology that allows the inclusion of up to 100,000 simple logic gates on a single chip. 2) An integrated circuit that uses large scale integration.Mmain board: See motherboard.megabyte (MB):  A unit of data storage equal to 1024 kilobytes. See alsokilobyte.
User’s Manual Glossary-10Glossarymegahertz:  A unit of wave frequency that equals 1 million cycles per second. See also hertz.menu:  A software interface that displays a list of options on the screen. Also called a screen.microprocessor:  A hardware component contained in a single integrated circuit that carries out instructions. Also called the central processing unit (CPU), one of the main parts of the computer.mode:  A method of operation, for example, the boot mode, Standby Mode or the Hibernation Mode.modem:  Derived from modulator/demodulator, a device that converts (modulates) digital data for transmission over telephone lines and then converts modulated data (demodulates) to digital format where received.monitor: A device that uses rows and columns of pixels to display alphanumeric characters or graphic images. See also CRT.motherboard:  A name sometimes used to refer to the main printed circuit board in processing equipment. It usually contains integrated circuits that perform the processor’s basic functions and provides connectors for adding other boards that perform special functions. Sometimes called a main board.MP3: An audio compression standard that enables high-quality transmission and real-time playback of sound files.Nnon-system disk:  A formatted floppy disk you can use to store programs and data but you cannot use to start the computer. See system disk.nonvolatile memory:  Memory, usually read-only (ROM), that is capable of permanently storing information. Turning the computer’s power off does not alter data stored in nonvolatile memory.numeric keypad overlay:  A feature that allows you to use certain keys on the keyboard to perform numeric entry, or to control cursor and page movement.OOCR:  Optical Character Recognition (reader). A technique or device that uses laser or visible light to identify characters and input them into a storage device.online state:  A functional state of a peripheral device when it is ready to receive or transmit data.operating system:  A group of programs that controls the basic operation of a computer. Operating system functions include interpreting programs, creating data files, and controlling the transmission and receipt (input/output) of data to and from memory and peripheral devices.
User’s Manual Glossary-11Glossaryoutput:  The results of a computer operation. Output commonly indicates data. 1) printed on paper, 2) displayed at a terminal, 3) sent through the serial port of internal modem, or 4) stored on some magnetic media.Pparallel interface:  Refers to a type of information exchange that transmits information one byte (8 bits) at a time. See also serial interface.parity:  1) The symmetrical relationship between two parameter values (integers) both of which are either on or off; odd or even; 0 or 1. 2) In serial communications, an error detection bit that is added to a group of data bits making the sum of the bits even or odd. Parity can be set to none, odd, or even.password:  A unique string of characters used to identify a specific user. The computer provides various levels of password protection such as user, supervisor and eject.pel:  The smallest area of the display that can be addressed by software. Equal in size to a pixel or group of pixels. See pixel.peripheral component interconnect:  An industry standard 32-bit bus.peripheral device:  An I/O device that is external to the central processor and/or main memory such as a printer or a mouse.pixel:  A picture element. The smallest dot that can be made on a display or printer. Also called a pel.plug and play:  A capability with Windows that enables the system to automatically recognize connections of external devices and make the necessary configurations in the computer.port:  The electrical connection through which the computer sends and receives data to and from devices or other computers.Power Saver: A TOSHIBA utility that lets you set the parameters for various power-saving functions.printed circuit board (PCB): A hardware component of a processor to which integrated circuits and other components are attached. The board itself is typically flat and rectangular, and constructed of fiberglass, to form the attachment surface.program:  A set of instructions a computer can execute that enables it to achieve a desired result. See also application.prompt:  A message the computer provides indicating it is ready for or requires information or an action from you.
User’s Manual Glossary-12GlossaryRRadio frequency interference (RFI) shield:  A metal shield enclosing the printed circuit boards of the printer or computer to prevent radio and TV interference. All computer equipment generates radio frequency signals. The FCC regulates the amount of signals a computing device can allow past its shielding. A Class A device is sufficient for office use. Class B provides a more stringent classification for home equipment use. TOSHIBA portable computers comply with Class B computing device regulations.Random Access Memory (RAM):  High speed memory within the computer circuitry that can be read or written to.restart:  Resetting a computer without turning it off (also called "warm boot" or "soft reset"). See also boot.RGB:  Red, green, and blue. A device that uses three input signals, each activating an electron gun for a primary additive color (red, green, and blue) or port for using such a device. See also CRT.RJ11:  A modular telephone jack.RJ45:  A modular LAN jack.ROM: Read Only Memory: A nonvolatile memory chip manufactured to contain information that controls the computer’s basic operation. You cannot access or change information stored in ROM.SSCSI:  Small Computer System Interface is an industry standard interface for connection of a variety of peripheral devices.SD card:  Secure Digital cards are flash memory widely used in a variety of digital devices such as digital cameras and Personal Digital Assistants.serial communications:  A communications technique that uses as few as two interconnecting wires to send bits one after another.serial interface:  Refers to a type of information exchange that transmits information sequentially, one bit at a time. Contrast: Parallel interface. SIO:  Serial Input/Output. The electronic methodology used in serial data transmission.soft key:  Key combinations that emulate keys on the IBM keyboard, change some configuration options, stop program execution, and access the numeric keypad overlay.software:  The set of programs, procedures and related documentation associated with a computer system. Specifically refers to computer programs that direct and control the computer system’s activities. See also hardware.stop bit:  One or more bits of a byte that follow the transmitted character or group codes in asynchronous serial communications.
User’s Manual Glossary-13Glossarysubpixel:  Three elements, one red, one green and blue (RGB), that make up a pixel on the color LCD. The computer sets subpixels independently, each may emit a different degree of brightness. Seealso pixel.synchronous:  Having a constant time interval between successive bits, characters or events.system disk:  A disk that has been formatted with an operating system. For MS-DOS the operating system is contained in two hidden files and the COMMAND.COM file. You can boot a computer using a system disk. Also called an operating system disk.Tterminal:  A typewriter-like keyboard and CRT display screen connected to the computer for data input/output.TFT display:  A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology with thin film transistor (TFT) to drive each cell.Touch Pad:  A pointing device integrated into the TOSHIBA computer palm rest.TTL:  Transistor-transistor logic. A logic circuit design that uses switching transistors for gates and storage.UUniversal Serial Bus:  This serial interface lets you communicate with several devices connected in a chain to a single port on the computer.VVGA:  Video Graphics Array is an industry standard video adaptor that lets you run any popular software.volatile memory:  Random access memory (RAM) that stores information as long as power is supplied to the computer.Wwarm start:  Restarting or resetting a computer without turning it off.window:  A portion of the screen that can display its own application, document or dialog box. Often used to mean a Microsoft Windows window.Wireless LAN:  Local Area Network (LAN) through wireless communication.write protection:  A method for protecting a floppy disk from accidental erasure.
User’s Manual Index-1IndexAAC adaptor 3-3additional 3-28, 3-38connecting 1-6ASCII characters 5-9BBatterycharging 6-8extending life 6-10indicator 2-12, 6-4location 2-7monitoring capacity 6-9real time clock 3-3, 6-6save mode 3-7types 6-5Battery charger 3-29, 3-38Battery pack 2-7, 3-2additional 3-27replacing 6-11BIOS Setup 7-8Bluetooth 3-5, 4-37Bluetooth Stack for Windows by Toshiba 3-9problems 8-21Wireless Optical Mouse with Bluetooth Technology 3-37Wireless Stereo Headset with Blue-tooth Technology 3-37Boot Priority 7-3Bridge media slot 2-4indicator 2-11using 3-15CCache memory 3-1Cleaning the computer 4-42Cooling vents 2-3, 2-7DDC IN indicator 2-11, 6-4Display 3-4automatic power off 3-6brightness decrease 5-5brightness increase 5-5controller B-1hinge 2-9opening 1-8screen 2-9DLA for TOSHIBA 3-11, 4-30Docking port 2-7Documentation list 1-2DVD Super Multi driveproblems 8-11using 4-19writing 4-25DVD-ROM driveproblems 8-9using 4-19DVD-ROM&CD-R/RW driveproblems 8-10using 4-19writing 4-23EEquipment checklist 1-1External monitor 2-6, 3-31problems 8-18
User’s Manual Index-2TECRA M7FFingerprint Sensorlocation 2-8problems 8-16using 4-12Floppy disk care 4-31Fn + Ctrl (enhanced keyboard simulation) 5-3Fn + Enter 5-3Fn + Esc (sound mute) 5-3Fn + F1 (instant security) 5-4Fn + F10 (Arrow mode) 5-3Fn + F11 (Numeric mode) 5-3Fn + F12 (ScrLock) 5-3Fn + F2 (power save mode) 5-4Fn + F3 (standby) 5-4Fn + F4 (hibernation) 5-4Fn + F5 (display selection) 5-4Fn + F6 (internal LCD screen brightness decreases) 5-5Fn + F7 (internal LCD screen brightness in-creases) 5-5Fn + F8 (wireless setting) 5-5Fn + F9 (Touch Pad) 5-5Fn + space (LCD screen resolution selec-tion) 5-6Fn + Tab (Optical disc drive power) 5-6Fn-esse 3-9Function keys 5-2GGraphics controller 3-4HHard disk drive 3-3automatic power off 3-6HDD indicator 2-12Heat dispersal 3-7, 4-45Hibernation 3-8, 5-4Hot keys 3-6display selection 5-4instant security 5-4Internal LCD screen brightness de-crease 5-5Internal LCD screen brightness in-crease 5-5power save mode 5-4sound mute 5-3standby 5-4wireless setting 5-5HW Setup 3-8accessing 7-1Boot priority 7-3CPU 7-6device config 7-7display 7-2general 7-2keyboard 7-5LAN 7-6USB 7-7window 7-1Ii.LINK 2-4, 3-34connecting 3-35disconnecting 3-35precautions 3-34problems 8-19Indicators 2-11, 6-4KKeyboard 5-1emulating enhanced keyboard 5-2Fn Sticky key 5-6Function keys F1...F12 5-2Hot keys 5-3problems 8-7typewriter keys 5-1Windows special keys 5-7Keypad overlay 3-6, 5-7Arrow mode 5-7Numeric mode 5-8temporarily using normal keyboard (overlay on) 5-8temporarily using overlay (overlay off) 5-8turning on the overlays 5-7LLAN 3-5, 4-40cable types 4-40connecting 4-40disconnecting 4-41
User’s Manual Index-3TECRA M7jack 2-6LAN active indicator 2-6Link indicator 2-6problems 8-20MMedia care 3-15, 4-31Card care 3-15CD/DVDs 4-31floppy disks 4-31Memory card care 3-15Memory 3-2expansion 3-22, 3-38installing 3-23problems 8-17removing 3-26Memory Stick/Memory Stick Pro 3-18inserting 3-18problems 8-13removing 3-19Modem 3-5, 4-33connecting 4-35disconnecting 4-36jack 2-5problems 8-19properties menu 4-34region selection 4-33Moving the computer 4-42MultiMediaCard 3-20inserting 3-21problems 8-14removing 3-21PPasswordpower on 3-6problems 8-7starting the computer by 6-16Supervisor 6-15user 6-13PC card 3-13inserting 3-13location of slot 2-3problems 8-12removing 3-14Pointing DeviceReserve Pen 4-2Tablet PC Pen 4-2Touch Pad 2-9, 4-1Touch Pad control buttons 2-9, 4-1Touch Pad location 2-8using 4-1Powerbutton location 2-8conditions 6-1hibernation mode 1-11indicators 6-4panel on/off 3-7, 6-18shut down mode (boot mode) 1-9standby mode 1-10system auto off 6-18turning off 1-9turning on 1-8ProblemsAC power 8-5Analyzing symptoms 8-2Battery 8-5Bluetooth 8-21DVD Super Multi drive 8-11DVD-ROM drive 8-9DVD-ROM&CD-R/RW drive 8-10External monitor 8-18Fingerprint Sensor 8-16Hard disk drive 8-8Hardware and system checklist 8-3i.LINK (IEEE1394) device 8-19Internal LCD display panel 8-8Keyboard 8-7LAN 8-20Memory expansion 8-17Memory Stick/Memory Stick Pro 8-13Modem 8-19MultiMediaCard 8-14Overheating power down 8-4Password 8-7PC card 8-12Pointing device 8-14Power 8-4Real Time Clock 8-7SD card 8-13Self test 8-4Sound system 8-18System start-up 8-3TOSHIBA support 8-22
User’s Manual Index-4TECRA M7Touch Pad 8-14TV output signal 8-19USB device 8-17USB floppy disk drive 8-12USB mouse 8-15Wireless LAN 8-21xD picture card 8-13Processor 3-1RRecordNow! 3-10, 4-29Recovery HDD 1-14Recovery Media 1-14Restarting the computer 1-13SSD card 3-16formatting 3-18inserting 3-16problems 8-13removing 3-17SD memory card 3-17SDIO card 3-18Security lock 3-37location 2-3Slice Expansion Battery 3-38, 6-6Soft keysenhanced keyboard 5-2Enter 5-3right Ctrl key 5-3ScrLock 5-3Sound system 4-32headphone jack 2-2microphone jack 2-2microphones 2-2mute hot keys 5-3problems 8-18Stereo speakers 2-9volume control 2-3Standby 3-8setting 1-10System automatic 3-6TTOSHIBA Assist 3-10TOSHIBA ConfigFree 3-10TOSHIBA Controls 3-8TOSHIBA Express Port Replicator 3-36, 3-38TOSHIBA HDD Protection 3-7TOSHIBA Mic Effect 3-10TOSHIBA Mobile Extension 3-10TOSHIBA PC Diagnostic Tool 3-10TOSHIBA Power Saver 3-8TOSHIBA SD Memory Boot Utility 3-9TOSHIBA Zooming Utility 3-9Touch Pad 8-14TV 3-32UUSB deviceproblems 8-17USB floppy disk driveproblems 8-12VVideo RAM 3-2Volume control 2-3WWireless communication 4-36indicator 2-12, 4-39Wireless communication switch 2-2, 4-39Wireless LAN 3-5, 4-36problems 8-21XxD picture card 3-19inserting 3-20problems 8-13removing 3-20

Navigation menu